[VIA] kt4v-viakt400 chipset memory problems

I am currently running with (2) 256mb ddr400 sticks in the slot 1 and 2 position as registered by the computer evan though the modules say pc3500 Geil ultra . when I try to add a 512mb pc3200 module it refuses to start up . when I remove the module everything works fine . what gives? am I going to have to remove the original modules and install two matched modules in slots 1/2 to achieve my desired goal of 1gb ddr 400 mem or even switch to pc2100/2700 mem to achieve this?

If you don't want problems such as the one you just suffered, you should avoid mixing difs. brand/speed/make memory. So, best way to upgrade your memory is to buy 1 Gb. stick or 2 identical 512 Mb. sticks. As you don't say what FSB CPU are you running in your system, I'll say you should go for same FSB speed to run them 1 : 1

Similar Messages

My original apple id is not an email address . I bought iCloud memory via that same account no problem. When setting up iCloud on iPad you cannot have a primary iCloud account unless it has an email address . Made new account but can you change originalI'

My original apple id is not an email address .
I bought iCloud memory via that same account no problem.
When setting up iCloud on iPad you cannot have a primary iCloud account unless it has an email address .
Made new account as per instruction ie [email protected] works fine
BUT as I want to utilise the money spent on the additional memory it would be great to use the initial account set up as my primary HOWEVER as far as I have tried the initial apple ID CANNOT be changed. Bit confused actually any usefull guidance will be greatly appreciated. Thanks

See Here > Apple ID: Contacting Apple for help with Apple ID account security
Ask to speak with the Account Security Team...
lmerchant wrote:
My new phone has an old apple ID associated with iCloud only. I cannot delete the account as it has "Find my iPhone" turned on.
Activation Lock in iOS 7 > http://support.apple.com/kb/HT5818

Memory problems with PreparedStatements

Driver: 9.0.1 JDBC Thin
I am having memory problems using "PreparedStatement" via jdbc.
After profiling our application, we found that a large number oracle.jdbc.ttc7.TTCItem objects were being created, but not released, even though we were "closing" the ResultSets of a prepared statements.
Tracing through the application, it appears that most of these TTCItem objects are created when the statement is executed (not when prepared), therefore I would have assumed that they would be released when the ResultSet is close, but this does not seem to be the case.
We tend to have a large number of PreparedStatement objects in use (over 100, most with closed ResultSets) and find that our application is using huge amounts of memory when compared to using the same code, but closing the PreparedStatement at the same time as closing the ResultSet.
Has anyone else found similar problems? If so, does anyone have a work-around or know if this is something that Oracle is looking at fixing?
Thanks
Bruce Crosgrove

From your mail, it is not very clear:
a) whether your session is an HTTPSession or an application defined
session.
b) What is meant by saying: JSP/Servlet is growing.
However, some pointers:
a) Are there any timeouts associated with session.
b) Try to profile your code to see what is causing the memory leak.
c) Are there references to stale data in your application code.
Marilla Bax wrote:
hi,
we have some memory - problems with the WebLogic Application Server
4.5.1 on Sun Solaris
In our Customer Projects we are working with EJB's. for each customer
transaction we create a session to the weblogic application server.
now there are some urgent problems with the java process on the server.
for each session there were allocated 200 - 500 kb memory, within a day
the JSP process on our server is growing for each session and don't
reallocate the reserved memory for the old session. as a work around we
now restart the server every night.
How can we solve this problem ?? Is it a problem with the operating
system or the application server or the EJB's ?? Do you have problems
like this before ?
greetings from germany,

MS-6380 Memory Problem

I have a MS-6380E with the latest BIOS and chipset drivers. Athlon 1.5 Ghz processor, Geo4 Ti series card with 64MB ram and latest drivers and an SBLive Platinum 5.1 card, with the latest drivers. Windows XP Pro is the operating system. The system has 2 PC2100 256MB sticks of DDR ram on the board. This past weekend I tried to install a 3rd chip, PC2100 512MB chip to bring the system up to a Gig of ram. The system would reboot immediatly upon logging into Windows. I took the memory back and exchanged it for another. Installed it with similar results. I tried all three slots with the new memory and the two existing. No, I didn't try the new memory by itself. I finally go it to appear stable for a little bit but I also play Dark Age of Camelot and the latest symptoms were that the system would kick me back to the desktop as soon as I got to the initial "connecting" screen in Dark Age. I also had other odd behaviour with the additional ram installed like my modem taking longer to validate my connection. When I went back to the pre-existing configuration 512MB total, everything would stabilize. The DDR brand was Centron, I know it's not the same manufacturor as my other two sticks but I don't recall the brand on those. Also, just in case you needed to know Dark Age of Camelot is an MMORPG. I checked their tech section and nothing on this problem and their game. I've since returned the memory and have resigned to maxing out at 512MB tho the system specs say I can go to 3GB. I really like this board but am frustrated at the memory problem.

http://www.msi.com.tw/program/service/forum/search.php?boardid=
6380 covers a hell of a lot of boards
getting same make and model of ram is generally advisable to

Nokia C5-03 Low memory problems ( Other Files )

Please help. I have a nokia C5-03 the handset is showing phone memory is full. I have checked and uninstalled all unecessay applications. But problem is still there. when i check the phone memory it indicates that i have other files of 42mb installed and using phone memory. however i am unable to check what other files are installed or classfied as other files. Can you please assist me so i can know what these other files consist of or where they are located.

Hi Thetao,
I typed a more extensive reaction before, but it got lost when I pressed "post". Therefore I just respond to the main points that you mentioned (and some I found out myself).
Strange: I can't find the 40 MB Maximum User Storage on the Nokia website anymore (nor the 75 MB). But it sounds very familiar to me. It looks to me as if they removed this from the phone specs, also of other Smartphones by the way.
Yesterday, I deleted some small apps that I don't use (anymore) such as InternetRadio and I also removed Nokia email. Although the apps were below 2 MB together, this freed up over 7 MB of Phone memory (24 MB free now)! I think there were still some old emails stored in C: which I couldn't delete any other way. This helped me a great deal already but I tried your suggestions as well.
1. No map data or CITIES folder on C: 2. Switched messages memory to phone (and phone to offline mode) and I did indeed find a forgotten email account with 30 email messages. Not much but I had 24,7 MB free after that. Of course, I put messages memory back to the memorycard. 3. Used the free edition of Y-Browser to manually delete the cache folder. Not much data in that, but 25,1 MB free after that. Nice tool, with which you can reach folders that normally stay hidden! Used YBrowser to search all C: for files over 300 kB. Only 2 files: boot_space.txt in C:\ (500 kB, contains only the X repeatedly as far as I see, but is probably essential for the operating system) and C:\resource\python25\pyton25.zip (1 MB). It looks like an installation package, but I'm not sure if I can delete it. By the way: YBrowser hasn't made a shortcut in one of the menus. Only way that I found to start it was to look for it using the Phone's search function. Is there a way to make this shortcut myself?
4. Yes I did. No Images folder on C: anymore, nor other big files (see point 3)
5. I use Bluetooth for file transfer sometimes, mainly for installation files (such as YBrowser.sis, but I did this one via USB-cable). However, no big files are left on C: so I don't think I have this problem.
6. I tried to delete Nokia Chat yesterday as well (with the other apps), but it won't be uninstalled the normal way as it says "Uninstall cancelled" (not sure about the exact translation since my phone 'speaks' Dutch) Do you know if there's another way to get rid of this 3 MB app that I don't use at all?
I think I may have found an explanation and a solution for the memory problem while navigating. You mentioned the "memory in use" in the map settings. Above that option there's a slide bar for the % of memory that the navigation can use. Standard is 70%. I always thought this was about storage memory on (in my case) the memorycard. Another topic mentioned that this the working memory (so the RAM) that the navigation may use. Setting it to 70% means there's only 30% left for other apps that run in the background. The other topic states that this is nog enough so the slider should be set to for instance 30% for navigation leaving 70% free for "the phone". From behind my computer, navigation seems much more stable. I'll try this setting in my car soon and let you know how it works.
Thanks a lot for thinking along with me so far! There's already 25,1 MB of space, which is great since it was only 7 MB last Sunday. And navigation looks more stable. I'd appreciate if you have some more answers to my latest questions, but if not I think my phone will work a lot better already!
Regards, Paul

Memory problem with 5330 XpressMusic

Hi,
I seem to have a memory problem with my 5330, I have a 1Gb micro disc installed. My son sent me a photo from his phone, when it arrived I got a warning on the scren that 'there is not enough memory to receive messages', I have tried to delete as much as I can, a lot tells me I can't delete it, but I still get the same warning. This warnig shows up each time I switch on the phone. How can I get myself more space? Can I move things from the phone memory to the memory card?
Gerald
Message Edited by warmbells on 01-Nov-2009 06:19 PM

Are you sure you're using a 5330 XpressMusic? Or is it a 5320 XpressMusic? The former is yet to be released, AFAIK.
Assuming that you are using a 5320, try these steps:
-> Move all photos, music, videos stored in the phone memory to the memory card. You can use the built-in File Manager to accomplish this.
-> Delete all files that you would've received via bluetooth, present in your Inbox. You can save them to the mass storage.
-> Clear the browser cache.
-> Clear the Sent Items folder.
-> Make sure you don't have too many messages in your inbox.
Hope this helps
Cheers,
DeepestBlue
5800 XpressMusic (Rock Stable) | N73 Music Edition (Never Say Die) | 1108 (Old and faithful)
If you find any post useful, click on the Green "Kudos" Button on the left to say Thank You...

Memory Problem With 4gb Crucial Ballistix and Asus M4A785TD-V EVO

motherBoard: ASUS M4A785TD-V EVO
bios Version :2005
Video: amd hd5750
Processor: AMD PHENON II X2 550 3.100MHZ
Memory: Crucial
Modele Memory: blt4g3d1608dt1tx0
Capacity: 4GB
greetings to all
i have asus m4a785td-v evo mobo. i ve bought 4 gb crucial ballistix ram today. it says on product its 1600 mhz and cl8 but it shows on my pc 1333 mhz and cl9. when i was searching for this problem i came across this topic: http://forum.crucial.com/t5/Crucial-Ballistix-gaming-memory/Memory-Probleme-With-8GO-Crucial-Ballistix-and-Asus-M4A785TD-V/td-p/9464 can i apply the same settings? how can i fix that? is it possible via bios settings? thx in advance and sry for my bad english. here is some screenshots:

I am not good at RAM setting but the 'Timings Table' shows there is XMP-1600 profile available so I believe it would be enough to turn on that memory profile in BIOS.

G2Ti Pro (SM-8855) with VIA Apollo Pro133 Chipset!

I am using a MS-8855 (G2Ti Pro / Pro-t) vga card in my Asus P3V133 (VIA Apollo Pro133 Chipset) motherboard and when I play any game my computer freezes , I installed other similar drivers but it continued with the same problem. How I can solve that?
Mother Board: ASUS P3V133 ( agp 2x max)
Chipset: VIA Apollo Pro133
Proc: Pentium 3 733MHz (133)
Mem: 256 pc-133
Video: MSI Geforce2 ti pro-t (sm-8855)
Audio: Creative Live Value!
OS: WinXP SP1, Win98 SE and Linux

BRAZIL-BR,
Make sure you have the latest 4in1 Drivers from Via.
Good Luck,
Richard

K9VGM-V Memory problem

Hello, Bought a new computer parts since i wanted to improve my comp overall. Anyway when i had build it together and tryed to start it, it just gave away beeps. So i called my friends and someone of them said try remove one of the memory's from DIMM2 so i did and it started. But could just run on Safe mode in windows(and change bios), i tryed switch the memory's and both worked on DIMM1. And when i put one of the memory's in DIMM2 it just give away Beep's.
Its my first time i build a computer so i dont know the common misstakes i could done, at last i went to MSI homepage and went to check forum and i saw someother posts about memory problems, tryed those tips out but didnt help. So now im here to ask if anyone of you know what the problem could be, could it possible be that its not dual channel memorys or CMOS or anything else? :P
My comp part's:
Mainboard: K9VGM-V, VIA K8M890, Socket-AM2,m-ATX, DDR2, SATA, LAN, VGA, PCI-Ex16
Processor: AMD Athlon 64 X2 6000+ 3.0GHz Socket AM2 2MB, 90nm(89W), BOXED w/fan
Power Supply: Chieftec Power supply ATX 400W, 120mm Fan, Active PFC, 2xSATA, PCI-E, 20/24pin
Memorys: Crucial DDR2 PC5300 2048MB CL5Kit w/two matched DDR2 PC5300 1024MB CL5
Graphic card: Gainward GeForce 8600GT 512MB GDDR3,PCI-Express, DVI/HDMI/VGA/HDCP, SilentFX

Try with better PSU.
>>> PSU's---2 x 12v---The Dual Rail Myth <<<
>>> Is your problem caused by your PSU? <<<
Good PSU recommendation can be found here:
https://forum-en.msi.com/index.php?topic=112039.msg836246#msg836246

[VIA Series] Help with Memory Type

Can I use high density memory with VIA P4M266A + 8237 Chipset Based?

Yes,
Please give more details of setup first

VIA KT4V and the latest BIOS

Helllo! I have a question:
I have a MSI VIA KT4V MB with the latest BIOS version (04-08-09), and I wonder if this BIOS-version supports Barton XP 3000+ CPU?
Chassi:    Chieftec Dragon Midi Tower
PSU:    Antec True Power 480P (480W) | +5V/38A | +3,3V/30A | +12V/22A |
MB:    MSI KT4 V (VIA KT400 chipset with BIOS v1.9)
Videocard: MSI Geforce 4 ti 4600 128MB
Soundcard: AC97 (integrated on MB)
NIC:    Jensen PCI Fast Ethernet
CPU:    AMD athlon XP Barton 2500+
RAM:    2 * 512MB Kingston PC-2700 (333 MHz FSB)
HD1:    1 * 120GB, 7200rpm, UATA100, 2 MB cache IBM deskstar
HD2:    1 * 120GB, 7200rpm, UATA100, 8 MB cache Western Digital
CD:    1 LG CD/RW 48x/16x/48x
DVD:    1 LG DVD RAM 8x (4081B)
Floppy:    1 st NoName
Monitor: 17" TFT Fujitsu/Siemens scaleo CTM7010
OS:    Windows 2000 Advanced server (SP 4, directX 9.0b)
Keyboard: IBM (PS2)
Mouse:    Logitech MX510 (optical)

Bios version 1.B adds Sempron support. Your board supports the XP3000+ Barton with 333Mhz FSB only not 400Mhz. Details here.

Memory Problem with SEt and GET parameter

hi,
I m doing exits. I have one exit for importing and another one for changing parameter.
SET PARAMETER exit code is ....
*data:v_nba like eban-bsart,
       v_nbc like eban-bsart,
       v_nbo like eban-bsart.
       v_nbc = 'CAPX'.
       v_nbo = 'OPEX'.
       v_nba = 'OVH'.
if im_data_new-werks is initial.
if im_data_new-knttp is initial.
    if im_data_new-bsart = 'NBC' or im_data_new-bsart = 'SERC' or im_data_new-bsart = 'SERI'
       or im_data_new-bsart = 'SER' or im_data_new-bsart = 'SERM' or im_data_new-bsart = 'NBI'.
      set parameter id 'ZC1' field v_nbc.
    elseif im_data_new-bsart = 'NBO' or im_data_new-bsart = 'NBM' or im_data_new-bsart = 'SERO'.
      set parameter id 'ZC2' field v_nbo.
    elseif im_data_new-bsart = 'NBA' or im_data_new-bsart = 'SERA'.
      set parameter id 'ZC3' field v_nba.
    endif.
endif.
endif. *
and GET PARAMETER CODE IS....
get parameter id 'ZC1' field c_fmderive-fund.
get parameter id 'ZC2' field c_fmderive-fund.
get parameter id 'ZC3' field c_fmderive-fund.
FREE MEMORY ID 'ZC1'.
FREE MEMORY ID 'ZC2'.
   FREE MEMORY ID 'ZC3'.
In this code i m facing memory problem.
It is not refreshing the memory every time.
So plz give me proper solution.
Its urgent.
Thanks
Ranveer

Hi,
   I suppose you are trying to store some particular value in memory in one program and then retieve it in another.
If so try using EXPORT data TO MEMORY ID 'ZC1'. and IMPORT data FROM MEMORY ID 'ZC1'.
To use SET PARAMETER/GET PARAMETER the specified parameter name should be in table TPARA. Which I don't think is there in your case.
Sample Code :
Data declarations for the function codes to be transferred
DATA : v_first TYPE syucomm,
       v_second TYPE syucomm.
CONSTANTS : c_memid TYPE char10 VALUE 'ZCCBPR1'.
Move the function codes to the program varaibles
v_first = gv_bdt_fcode.
v_second = sy-ucomm.
Export the function codes to Memory ID
EXPORT v_first
       v_second TO MEMORY ID c_memid.        "ZCCBPR1 --- Here you are sending the values to memory
Then retrieve it.
Retrieve the function codes from the Memory ID
IMPORT v_first TO v_fcode_1
         v_second TO v_fcode_2
FROM MEMORY ID c_memid.                                   "ZCCBPR1
FREE MEMORY ID c_memid.                                   "ZCCBPR1
After reading the values from memory ID free them your problem should be solved.
Thanks
Barada
Edited by: Baradakanta Swain on May 27, 2008 10:20 AM

Memory Problems with Adobe PDF iFilter for 64-bit

In preparation to rebuild my Windows Search Index, I installed the Adobe PDF iFilter for 64-bit on my system (Vista Business 64). When I finally rebuilt the index, I wasn't too surprised by what I saw happen, namely, the SearchFilter.exe process would kick in whenever I wasn't using the system and just eat RAM. One time I turned it on and it had allocated over 4,000 MB (and my system only has 4,030 MB available) so of course it was forcing all the other processes to hard fault (ie. everything was moving like molasses--for example, it took 20 minutes to put the thing to sleep). But I just let it do it's work, figuring that perhaps this was to be expected relative to the small library of PDF's that I've accumulated on my computer, ranging from LaTeX generated text files, to containers for hi-res scans. So, after a day and a half of basically not using my laptop, everything finally calmed down and I enjoyed the benefits of searching the content of my library from the Windows Start menu--for a short while.
However, to my dismay I've encountered the problem that this freezing of my computer would now occur after everytime I download a new PDF (in this particular case they were Google Books scans) and then left the computer to idle. Again, the SearchFilter.exe would allocate all of my RAM for itself and just push everything else onto the Virtual RAM, which means the SLOWEST possibly fetching you can get. I had to uninstall as this was making my computer unusable for 15-30 minutes after each idle. Everything is back in working order without the iFilter, but I would like to know if anyone has reported such problems on x64 systems. Obviously, I will also report the problem to Microsoft, since the search engine should certainly have the precaution to handle such memory problems.   However, it is a problem that is created by the Adobe PDF iFilter interacting with the Windows Search engine.

Hello,
We believe we have figured this out. It looks like it has to do with the length of the default folder location for the Adobe iFilter.
I was able to reproduce the issue and the following resolved it for me. See if this resolves it for you all as well.
Here is how to get Adobe Version 11 PDF filter to work.
1 . If you haven’t already, run the following in SQL Server:
Sp_fulltext_service ‘Load_os_resources’, 1
Go
--you might also need to run:
sp_fulltext_service ‘Verify_signature’,0 --This is used to validate trusted iFilters. 0 disables it. So use with caution.
--go
2. Stop SQL Server. (Make sure FDHost.exe stops)
3.
Uninstall the Adobe ifilter (because it defaulted to having spaces or the folder name is too long).
4.
Reinstall the Adobe iFilter and when it prompts for where to install it, change it to: C:\Program Files\Adobe\PDFiFilter
5.  Once the installation finishes, go the computer’s Environment variables. Add the following to the PATH.
C:\Program Files\Adobe\PDFiFilter\BIN
NOTE: it must include the BIN folder
NOTE: If you had the OLD location that included spaces, remove it from the path environment variable.
6. Start SQL Server
7.  IF you had an existing Full-text index on PDFs, drop the full-text index and recreate it.
8. You should now get results when you run sys.dm_fts_index_keywords('db','tblname') --Note: Change db to be the actual database name and tblname to be the actual table name.
Give this a try and see if this fixes yours.
Sincerely,
Rob Beene, MSFT

Dual Channel memory problems on Neo 875P

I am having considerable trouble getting the NEO 875P to work with dual channel DDR400 DIMMs. I have two Kingston KVR400X64C25 DDR400 256MB memory modules, each of which works correctly by itself. However, once I move one
of the modules to channel B, I cannot boot my operating system (currently Windows XP.) The problem also occurs in Windows 2000, which I also have on the system. I receive blue screen errors that indicate paging/memory problems. I have upgraded my BIOS to the latest version (1.3)* in the hope that it would solve my problems, but it has not. The POST screen detects that there is 512MB of memory working in Dual Channel mode, but even when it does get through the O/S booting process (rarely), it crashes within minutes. Putting just one of the chips in makes the system perfectly stable. If anyone has any information, please let me know!
Thanks,
Jim Keller
http://www.centerfuse.net
* My board was dead after trying to flash the 1.3 BIOS, but after about 10 attempts of using CTRL+HOME method to recover the BIOS, it finally worked with version 1.0. I then re-flashed with 1.3, and it rebooted fine. Are there any updates about all of the problems with v1.3 ?

>I can only answer based on what I've read on this forum
I figured as much, I was just wondering if you knew whether MSI themselves frequents the forums or answers emails sufficiently.
I've had an interesting development though. I stumbled upon Tom's Hardware Guide's article about 875P motherboards at http://www17.tomshardware.com/motherboard/20030519/i875p-01.html
They mentioned that they needed to increase the memory voltage from 2.5 to 2.6 in the BIOS to get some memory modules to work. I did this, and for the first time, I am running in Dual channel DDR mode. However, the article also mentions that "the system does not run completely stably", so I guess I'll have to wait and see if it crashes again. However, I'm far enough beyond the XP splash screen to post this message, so I guess we're getting somewhere!
-Jim Keller
http://www.centerfuse.net

Memory problem with jdk/jre 1.1.8

My name is BERGMANN Yannick.
I'm working for IRM in Li?ge and we developped an application (user interface for an industrial measurement system) in Java (JDK/JRE version : 1.1.8).
We have a big memory problem with this application :
- This user interface is running on a WINDOWS NT PC with 128MB.
- This is the command to lanch our application :
C:\Program Files\JavaSoft\JRE\1.1\bin\jrew.exe" -ms32m -mx32m -cp "\Program Files\HMI\HMI.zip;\Velocis\Add_On\Jdbc\raima.jar;\Program Files\Swing-1.1.1\swingall.jar" be.irm.hmi.kernel.HMI -t15 -d"Velocis rdstcp" -newdb -mf1m -mr20
- When our application is running, everything seems to be OK in memory for it. The garbage collector seems to work properly and our application has always at least 5MB free memory (We use the java instruction "Runtime.getRuntime().freeMemory()" to know this).
- But when we look in the "Windows NT task manager" for the "jrew" application, the memory increases ALWAYS.
- After 5 days our application is completely frozen and blocked ...???
- here is a memory map of our Windows NT PC :
     "jre.exe"     "commit total"     "commit limit"     "commit peak"     "physical total"     "physical available"     "physical file cache"
Monday     92264     109256     194944     109424     130484     19492     6216
Thuesday     106196     123072     194944     123348     130484     6072     5840
Wednesday     110836     132288     194944     132416     130484     4408     5140
Thursday     108200     144980     194944     145140     130484     4888     5148
Friday     109440     158319     194944     161334     130484     4911     4992
Monday     111600     209060     228548     209148     130484     5184     3484
Have you any idea of what is happening with "jrew" in memory ?
We have had this problem for six month and we are totaly out of idea.
If you can give us any idea, we'll appreciate a lot.
Thanks in advance,
BERGMANN Yannick
IRM SA - Software Engineer
Tel. (32)4/239.90.10
Tel. (32)4/239.90.74 (direct)
Fax (32)4/263.40.97
E-mail [email protected]

We had a memory problem with a swing applet in our company. The major reason for this was that we added new components in a JTree and removed them later again, and the components we removed were never garbage collected. This was because with these components we added different listeners, and we didn't remove the listeners after we didn't need the components anymore. After we corrected this, the components where garbage collected.
Perhaps it's a similar problem you have, or I have no idea. Check that you remove actionlisteners, mouselisteners etc from components you want to be garbage collected.
You could also test your application with OptimizeIt to see what objects you create and how many you get of them over time: http://www.vmgear.com

[VIA] kt4v-viakt400 chipset memory problems

Similar Messages

Maybe you are looking for