[VIA] MSI KT3V and old Asus v3400tnt

Simple question....can i use an old Asus v3400tnt on a MSI KT3V ?? I have heard people talking about different volts in the AGP slot....1,5v or 3,3v...but i havent found any answers yet

Hi
This video card appears to be 1x-2x agp compliant so give it a try.  I could not find on the internet any instance of where the video card was used in a similar system.
I did find a lot of complaints about the video quality, especially in 3d environments. 
Low end video cards are very inexpensive and most of them will be a lot better than the old asus card since it appears to be only a 16meg card that used one of the early Riva tnt based chipsets.
See attached link for examples.
http://www.zipzoomfly.com/jsp/ProductList.jsp?ThirdCategoryCode=012203&SortBy=A

Similar Messages

  • MSI KT3V and T-bred 2000+

    Hi everyone!!
    I have bought a MSI KT3V and amd t-bred 2000+....
    My problem is that the BIOS shows CPUtemp: 56celcius and in MB5 it shows 50celcius...
    And I am wondering doesn't a AMD Thourghbred 2000+ go in 1.60v?? My sets a default in 1.65v and I can't get down to 1.60v.... WHAT IS WRONG!!!
    Should I upgrade the BIOS?? What would that help to??
    Please help me!!! ? :D

    1.65v is correct. I would go by the BIOS on the temps as they should be most accurate. http://www.almico.com Download Speedfan. I find most accurate for reading temps.
    56c is a little hot but acceptible.

  • [VIA] MSI-KT4AV and PC3200 RAM

    Hi guys!
    I've got an MSI-KT4AV mainboard, an Athlon XP 1800+, and a 512mb 400mhz Pc3200 module. This is the problem: I changed the DDR module from a 512mb 266mhz module to the 512mb 400mhz module; the mainboard has always worked fine with the first type of DDR module, but with the second one, the PC doesn't boot up. I try to change the memory but there is the problem yet. I try also the DDR Module 400mhz on another MSI Mainboard and that mobo function but not the MSI-KT4AV!!!!!   I'm sure that this mobo support the DDR Module 400mhz but I don't know why the system doesn't boot up. Another important thing: when I press the power button to switch on the PC, the Display is totally black with no signal but I can clearly hear 3 beeps from the motherboard: BEEP BEEP BEEP silence BEEP BEEP BEEP silence BEEP BEEP BEEP and so on....
    Can anyone help me?
    Thank you so much for Your reply....

    Did you try clearing your CMOS?  Look in your mobo manual if you don't know how.  That should fix it. :D.
    If it still doesnt, put your old stck of memory back in, go into your bios, and look under Frequency and Voltage.  Look for Memory voltage/vDimm.  Adjust it to 2.7 or 2.8v.  Save settings and exit.  Wait for windows to boot and shutdown.  Then try your new ram again. =D

  • MSI KT3V and Radeon 9100

    I have this mobo + graphic card, Athlon XP1700, and i have some sort of compatibility problem. When i install Windows 98se, DirectX 9 and any catalyst newer than 3.2 i've got ddhelp error communicate (always when i close simply tetris 4000 game). I check psu, ram, cpu cooling and card in other computer. In my older computer on mobo Aopen AK72(Via KX133) and Athlon 550 with this same via 4in1 drivers and directx i can use any catalyst without a problem. I change hdd too. Only things not tested are mobo and cpu, but i don't have any other. Does abybody knows what is goin on and how i can solve this problem?

    I think no. Only two, usb update and update for hard disk drive with 2MB cache. Do You think that's Windows 98SE problem?

  • MSI KT3V and Barton 2500+ Mobile

    I have those two and can't change the multiplier, which seems to be stuck at default 14x.

    i can tell you as it uses something like 15 as a default multiplier
    you would have to wire trick it
    then you would be able to select up to 12.5
    if you wanted 13,14, etc you would have to wire mod it to them

  • Following a software update, I can no longer access/authorise music purchased via iTunes from my old Apple ID, which I have not used for 8  years, and no longer have password.  Any ideas how I can re-access/recover that music?

    Following a software update, I can no longer access/authorise music purchased via iTunes from my old Apple ID, which I have not used for 8  years, and no longer have password.  Any ideas how I can re-access/recover that music?

    Apple ID FAQs  >  http://support.apple.com/kb/HT5622

  • HT1349 I am unable to download the newest version of iTunes 10.6 as i am missing .msi files and window installer package, can you please remove the old version and reinstall newest version, please?

    missing file to download itunes 10.6 - .msi. file and installation package

    Try to follow this guide to uninstall iTunes and all of its components: http://support.apple.com/kb/HT1925, then reinstall the latest version of iTunes.  You must follow this guide for this to be successful (uninstalling all components in the order specified).  This will not touch your iTunes library or data.

  • MSI KT3V + Sound Blaster Live Problem

    Hello Guys
    First, sorry for my english, i'm polish.
    Yesterday I sold my old motherboard (Shuttle AK32A), and i bought new motherboard MSI KT3V.  After instaling all peripheals I install on formated partition Win2000 SP3, Via 4in1 4.45, Drivers for my GF4 MX440, Network Adpater 3Com-SOHO, and sound blaster Live 1024. After this i instal game IGI2, and try play, After 30 s. in game main menu my computer crashes, screen is black, led on monitor is lights on yellow, after this i hear 10 - 20 second music from main menu in speakers, after this time my computer crashes completely, a hear beeeeeeeeep from speaker, and this moment I can only push reset button :(
    I try install many version drivers, from orginal cd, downloaded from internet. And newest version from 1.03.2002. An nothing :( I remove my Live 1024 from computer, and put friend live 5.1, and no changes, computer crashes :(
    My desktop resolution is 1128x864x32 bits 100hz When i try play  Divx movies after 1 - 2 minuts, frequency of my screen automatic swicth to 50 hz. If I try manualy switch frequency to old value (100 hz) nothing hapend, and i only can restart system :(
    When i work on my desktop (Word, IE, Winamp etc.) after 5 - 20 minutes, my system crashes too (yelow LED on monitoir, black screen, same situation) and I can only push reset button. When i remove card from pc, or turn card off in device manager all works fine.
    I upgarde bios to newer wersion (1.8), reinstall drivers, reinstall windows in APIC options turned off, remove network adapter, and no changes :(
    P.S. On old Mothearboard all works fine :(
    Anyone can help me solve this problem. Please
    Grettings Mark
    My Hardware
    MB: MSI KT3V
    Athlon 1700+
    512 MB DDR 266 Mhz
    3Com-SOHO Network Adapter
    WDC60 GB +  8.4GB Seagate
    GF4MX440 64MB InsideTNC
    CDRW Teac 40x, CD LG52x

    Quote
    Originally posted by maesus
    Also set PCI Delay Transaction enabled.
    This was a solution for my problem :-)
    Thank you very much. You have beer from me :-)
    Grettings

  • Deploy Acrobat Reader 10.1.3 via MSI Group Policy

    The purpose of this thread is to identify EASIEST way to create/obtain an MSI file of the LATEST VERSION of Acrobat Reader (currently 10.1.3 as of 7/19/2012) to be deployed via GPO.  I am not concerned with customizations of Reader settings as I have accomplished this already using Group Policy.
    It sounds so easy, but I have found it to be quite frustrating and extremely time consuming to figure this out.
    Here's what I have so far:
    To download the full installer from Adobe, you must first apply on Adobe's website to distribute Reader:
    http://www.adobe.com/products/reader/rdr_distribution1.html
    Once you submit the request, a short time later you'll get an e-mail with a link to download the full exe file of reader 10.1.3. 
    Here's a link that explains how to extract an MSI from this exe:
    http://blogs.adobe.com/dmcmahon/2010/06/16/how-to-extract-an-msi-file-from-the-exe-
    for-adobe-reader/
    Even with following those steps, I do not end up with an MSI file which will install 10.1.3.
    To try another route:
    There is also an Adobe FTP site.  If you navigate down into the Reader 10.1.0 folder there is an MSI file.  Good - but it's the old version.
    You would think that if you navigate into the 10.1.3 folder there would be an MSI there as well.
    Unfortunately there is not.  However, there is an MSP file found in the misc folder:
    I have tried several methods that are supposed to combine the MSP file with the MSI file - they have not worked.
    I have also tried several methods of modifying MSI files, and using the Adobe Cusomization wizard downloadable here:  http://www.adobe.com/support/downloads/detail.jsp?ftpID=4950
    I am unable to end up with a deployable MSI file for Reader 10.1.3.
    It's amazing that it's so complicated to deploy the latest version of Adobe Reader to my users.
    Does anyone have a comprehensive answer to this simple problem?  I do not want a link to a document with 20 pages explaining the theory of MSP files.  I am looking for a concise, step by step method to obtain an MSI for 10.1.3 quickly and easily.
    Thanks!

    First there isn't a single MSI file that will install Adobe Reader 10.1.3 available. There are two ways in which you can create an installer package that will install Adobe Reader 10.1.3. 
    1.  Bootstrapper
    -  Bootstrapper uses the Setup.ini file to create a chained installation process and is run from Setup.exe with a limited amount of installation switches available. 
    The process is documented in the Enterprise Administration Guide:  http://kb2.adobe.com/cps/837/cpsid_83709/attachments/Acrobat_Enterprise_Administration.pdf #page=77
    Here is a reference video on the process:  http://www.youtube.com/watch?v=9zYTUyOIcNk
    2.  AIP (Administrative Installation Point)
    - AIP uses the Windows Installer to create a decompressed updated full MSI based installer.  The process is documented in the Enterprise Administration Guide:  http://kb2.adobe.com/cps/837/cpsid_83709/attachments/Acrobat_Enterprise_Administration.pdf #page=70
    Here is a reference video on the process: http://www.youtube.com/watch?v=05XOKX0150w&feature=relmfu
    * Please note, that each installation method has it's advantages and disadvantages. Those aspects of each installation type need to be seriously considered for your specific environment and what will and will not work for the IT group and user groups within your enterprise before you decide upon one of them.
    Regards,
    Steve

  • Ti4200: problem with MSI CLOCK and info page

    Help!
    I've just install ti4200 128mb.  Everything runs fine, 3d mark even showing 9300+
    However, everytime I try to go to the MSI clock and information tab under display properties, I get a Microsoft reporting Error!
    I've tried this at W2k and also failed!
    I'm running up-to-date MSI v3000 nivida drivers.
    P4 2.5ghz
    ASUS P4S533
    512mb ddr333 ram
    WD 800jb
    I think its the motherboard, any ideas?!
    Thanks in advance.

    What's all talk about install other drivers ?.
    This is old problem if you would check some old threats.
    Problem lies in ASUS mobo, nothing can fix this, yet.  
    If you have ASUS mobo, use 40.41 Nvidia drivers with Coolbit to overclock you want be sorry.
    There is nothing in this flips that you miss.
    MSI support knows about this problem you can try to send them note, but they will not response.
    MSI support is one of the worst I have ever tried.
    Like you everthing else runs great.  I would be more unhappy about there is no hardware monitoring for G4ti, I thougt first it was in this flips but they only support it for G4 MX cards.  Don't know whey but I'm very angry and I will never get another MSI card.
    Regards
    Finnbogi
    G4ti 4400 VTD
    ASUS P4S533
    P4 1.8 @ 2.2

  • MSI mobos and ATI graphics card incompability!

    I don´t know how well known this problem is but I´ve seen it on this forum and when googling the internet you can find it!
    The issue is that I can´t get my HD5450(Sapphire) to work on my MS-7267 (945GCM5-F V2) mobo! The screen stays blank but the PC boots up and loads Windows.
    The HD5450 works fine on other mobos with different PSU´s ranging from 350 - 600 watts, but when trying different PSU´s on the 945GCM5-F V2 it doesn´t seem to help. I´ve also tried different bios settings, I´ve cleared CMOS, I´ve tried both dvi and vga outputs, I´ve disconnected as much as possible from the mobo except from the graphics card and the PSU, but nothing seems to help!
    Any ideas , someone?
    Tekrar!

    Thanks for all replies!
    I had this question on the AMD forum (AMD Game » AMD Technology » Radeon Graphics » MSI mobos and ATI graphics card incompability!) and here are some of the replies:
    "Well, its a known issue that older chipsets, like even AMD 580X chipset, doesn't work with 5k/6k series cards without a bios update from the manufacturer of the board.
    If its not working / posting / no video ect... You need to bug MSI to update the bios on the board to support the newer 5k/6k video cards. It may or may not happen. Several manufacturers have like Asus, and Gigabyte."
    "Same problem. 5450, MSI MS-7267 (945GCM5-F V2). Done the same plus updated msi mainboard bios using msi live update 5 etc. Waiting for reply from makers of graphics card and mainboard.
    I should add from what I've read in other threads and forums it seems to be an old mainboard problem not just related to the MSI 945GCM5-F V2. Some other manufacturers of mainboards have sent customers bios upgrades to get their cards working.
    As for your pci express version question. Well these problems seem to emerge when people have plugged these pci express version 2.1 cards into their pci express 1st generation slots. What exactly the problem is here? Leave that for manufacturers/experts to answer."
    "Tek , its hit or miss on the board + chipset combination on if the card will work or not. Sometimes they will work in old boards, Sometimes they will not w/o manufacturerer support.
    Its completely random from what I've seen on the forums at the times they were released , when people with old boards were asking why it wasn't working. And what they did to solve it. Most all of them emailed the manufacturer. Some of those said manufactureres provided beta bios back to the customers, some said your out of luck."
    Its true, this MSI MS-7267 (945GCM5-F V2) isn´t a new mobo, but when I get the 5450 to work without problem with an even older fujitsu mobo (last bios update long time ago) and a 350 watts PSU I think something´s wrong.
    So, a bios upgrade would probably fix it if the manufacturer (in this case MSI) just wanted to!
    Tekrar!

  • Updated bios via Live Update and now my Network card isn't detected

    I have an msi Z87-GD65 Gaming Motherboard and I updated some drivers and the bios via msi Live Update 6 last night and now my computer refuses to recognize my network adapter. The adapter is a TRENDnet N600, plugs into PCIe if I'm not mistaken. Wifi if my only option with this computer, I can't use ethernet, so it's really important I get the network card working again. I have had zero issues with it until this.
    The reason I was updating was to try to get my third monitor to work when plugged into the mobo, while my other two were plugged into the graphics card (which I also installed yesterday, but it's working fine). Note that it still was not working, but I had enabled the IGD Multi-Monitor from bios.
    Any suggestions would be appreciated. I did try uninstalling the drivers but it still won't detect the network card. I also tried disconnecting and reconnecting the network card (and I cleaned the port for good measure).
    I've only been using Windows computers for a year, so bear with me if there's stuff I don't know. Thanks in advance. I can try to get a full list of what was installed later tonight, but all of it that I can find has been uninstalled at this point.
    Note: I did not flash the bios when I installed, which I have now heard is a bad idea, apparently. l:

    what OS you are running?
    Quote
    Note: I did not flash the bios when I installed, which I have now heard is a bad idea, apparently. l:
    you said you've updated drivers & BIOS:
    Quote
    I updated some drivers and the bios via msi Live Update 6 last night and now my computer refuses to recognize my network adapter.
    can you clarify is you update BIOS too or not?
    and what is your current bios version?
    Quote
    and I updated some drivers
    what kind of drivers?
    Quote
    I did try uninstalling the drivers but it still won't detect the network card. I also tried disconnecting and reconnecting the network card (and I cleaned the port for good measure).
    have you tried to load last good known configuration or the last windows restore point?
    or to reinstall OS?

  • I recently purchased songs from itunes via my pc and I dont know how to get them onto my iphone? When I click the sync button it says I will lose all the music currently on my iphone.. Help :(

    I recently purchased songs from itunes via my pc and I dont know how to get them onto my iphone? When I click the sync button it says I will lose all the music currently on my iphone.. Help

    If you're syncing with a different iTunes library than the one you previously synced with, then there is no way around it. You're gonna loose the old data. The only way round it would be to make sure that all the music files on your iPhone is also in your iTunes library. If you still have access to the computer with the old library, you could copy the files on to an external harddrive, and then import them into your new iTunes library.
    If it is in fact the same library, then the music currently on your iphone, is also in your itunes library. Just make sure that the artists/albums/playlists, or whatever you sync contains these tracks, that you allready have on your phone and don't want deleted. What i do is, i create a playlist specifically for my iPhone, and i set it up to only sync with this playlist. Whenever i hear a track from my iTunes library or buy a new track that i want on my phone, i just drag it to this playlist and next time i synchronize, it's there without deleting anything else.

  • Loading attribute data via data source and file

    Hi gurus,
    My issue is that when I load excel file(2-column: matnr and werks) and load to master data via IP and DTP. After successful upload all available attriubute values which are retrieved from 0material_attr are gone away. Maybe deleted somehow.
    This is my issue.
    Can you help me which is the method loading some columns via sap extractor and one lıne via excel upload?
    Thanks.
    Eddy.

    Hello Eddy,
    I believe, the reason of getting your old data removing might be you are using the Full Upload via the Excel. In that recent excel you are not haviing the old records .
    Check the files and as suggested by raman ,if you have any changes in your master data then better to make delta relevant data source.
    Hope this helps !
    Regards
    YN

  • MSI blutetooth BToes (old) - which drivers for Win XP SP3?

    Hello,
    I'm using old Btoes bluetooth dongle and it's working fine on my old Win XP. Please help me which driver to download for the PC which runs on Win XP SP3?
    This is my dongle: http://www.msi.com/index.php?func=proddesc&prod_no=116&maincat_no=131&cat2_no=251&cat3_no=257
    I had lots of problem while installing it, so please help me if you were using the exact model. First of all, Windows tends to install its drivers and it works that way as well, but I can not make a serial connection to desired bluetooth device.
    I've tried using Win XP SP2 drivers listed here: http://www.msi.com/index.php?func=downloaddetail&type=driver&maincat_no=131&prod_no=116.
    However, it didn't work, I can not recall why. I had to reinstall the whole Windows after it. On the other computer it demanded presence of Btoes USB dongle in a USB port in order to boot Win. Like I said, lots of problems. It ended by installing the oldest drivers which came with the CD. Some of the options just don't work.
    Finally, when I take a look at properties, it says "Cambrige Sillicon Radio" version (I don't know how to UL a pic).
    I have a clean Win XP SP3 installation and don't want to ruin it -- which drivers to install and how? Thanks a lot!

    Quote from: Stu on 08-July-09, 01:35:58
    In all honesty, I would say yes, a more recent Bluetooth dongle will most probably be a lot easier for you to set up and use. For example, I use the built-in Bluetooth modules in my MSI Wind and Media Live, both of which use Toshiba hardware, and they are a dream to set up and use, compared to an old Trust bluetooth USB adapter I used some years back. They just work, full stop!
    Then I would follow your advice, and not try to use this Btoes 1.0 any more. Can you suggest me which one to purchase (just to be simple to install, uninstall, work fine with XP SP3 and, well, Win 7). Please note I might then use the new dongle for BT headset (which requires better speed?). Thank you.
    Previous discussion on Btoes 1.0 is over, thank you, all of you guys! 

Maybe you are looking for