[VIA Series] pt880 network problems

is anyone running PT880 Neo-LSR motherboard, windows xp sp2 and is able to use the lan port. I have two boards that seem to have the same problem loaded windows xp loaded the newest driver my pc come up fine my os see the nic card with no trouble no error it gets a ip but is unable to communicate in the network. I know is not my cable , switch or network since i am able to use a pci nic card and use the network with no problmes. so it this problem have a solution. Please help I am lost. I have tried several drivers bios and same problem.

Quote from: maralv on 04-September-05, 22:26:42
...loaded the newest driver my pc come up fine my os see the nic card with no trouble no error it gets a ip but is unable to communicate in the network...
maralv I had a similar problem recently. Everything LOOKED ok wrt IPs; the NIC could ping-and-be-pinged, but would not appear on the Windows network.
The problem went away when I uninstalled and reinstalled the NIC (VIA Rhine II) driver, reverting to the earlier MSI driver (sorry I don't recall if from the MSI disk or from the MSI website or from the VIA website--I will look).
EDIT: I'm now running the driver from viaarena.com. It's called Version 41 dated 06-May-05 and v3.44 shows-up in driver properties.
I had gotten an "updated" driver from the MS Windows website, and though it didn't fail right away, the only thing I can think is that it might be buggy in some way.

Similar Messages

[VIA Series] pt880 neo fsr - win xp pro install problem

Can you help me please?
In the course of Windows XP professional installation the Blue screen appear (IRQL_NOT_LESS_OR_EQUAL ***STOP: 0x0000000A) just after formating to ntfs. I have a inovated Bios version 1.9 (p4 3.0Ghz prescott). How next.

Hi,
Clarify:
Ram tested in PT880 chipset MSI mainboard
All DDR 400
1) Corsair 2-2-2-6
2) Twinmos 2.5-3-3-8
3) Infineon 2.5-4-4-8
4) PNY 2.5-4-4-8
5) Generic 3rd on 3rd (Cheap as chips stuff)
All tested in MSI mainboards as well . 865Platinum, 848P Neo-s and 845GE max
Please note:- I buy memory second hand, so I have to run memtest86.........
Also, I use Enermax PSUs.
Here to help
Del

PT880 Network Problem

I have a problem with my network connection and it looks like I can not fix it.
When I open Local Area Connection Status I do not see any activity on received and only a few bytes send. The network connector has 2 LED and only one is lit. The cable is OK because it is working with a different network card. The drivers for the motherboard are up to date.
This is the second PT880 mobo I buy and I have the same problem.
PLEASE HELP!!!!!!!

if this is the second PT880 that has done this to you, than i wouldn't suspect it to be your motherboards... it's got to be something else.. i would try a different cable (maybe it's went bad since you had it working on that other card) i would also try a different port on your hub/switch/router .
please give more details... i.e. what devices you are trying to connect, and for what reasons...

[VIA Series] PT880 doesn't recognize SATA disk at first boot

Hello everybody,
I have an MSI PT880 that works fine since one year with a 40 Gb ATA Maxtor hard drive.
I have just bought a 80 Gb SATA hard drive (Maxtor model 6L080M0) and have a very annoying problem:
- when I power on the computer, the VIA Sata Bios tells me that it doesn't find any Sata disk (and WinXP doesn't boot...),
- then if I press Ctrl-Alt-Del or the Reset button to boot again, the Sata Bios find the Sata disk (and WinXP starts...),
- as long as the computer isn't power off, I can reboot many times, the Sata Bios will always find the Sata disk and boot WinXP,
- but if I power off the computer, then power on, the Sata disk is not recognized.
I'm sure that the hard disk is not defective, because I have tried with another one (same model), and the same problem occurs.
I also tried to flash the Bios to the latest release (1.9), same problem...
My Config:
- MSI PT880 Neo-LSR with latest BIOS available (V1.9)
- INTEL Pentium 4C 2.4 Ghz
- 2 x 256 Infineon PC3200 (Dual mode)
- SAPPHIRE 9800 Pro
- ATA Hard drive: 40 Gb Maxtor (6E030L0) on first IDE controller
- SATA Hard drive: 80 Gb Maxtor (6L080M0) on first SATA controller
- Yamaha CRW-F1E and PIONNER DRV-105 optical drive on second IDE controller
- Win XP SP2

By "booting outside the case", you mean: extracting the motherboard from the case, putting it on a table, and trying to boot with only the mobo, the cpu, a new memory module, a simple video card, and the Sata HDD
I can try that but it' not easy... and the mobo is out of warranty
Don't you think that it could be a Sata Bios bug that appears only with this Maxtor hard drive model
As I've just bought this hard drive, I think that I'm going to exchange it for a Western Digital or a Seagate...

[VIA Series] PT880 Neo-FSR...SOOOO ANGRY!

Hi all,
I bought my PT880 Neo-FSR around late January/early February and until recently I hadn't been doing anything too memory intensive. Recently I bought World of Warcraft and have had many crashes. First it was tolerable, then when it got really bad i thought it was Blizzard's fault. I checked their boards and went throught their steps to rectify. One of which was the memtest86.
I ran the memtest and found that my Corsair was bad, both sticks! So i tried some Kingston. All of it also bad. 7 sticks of memory. I thought, "There's no way that could be right." So I ran memtest on another computer, a cheapie eMachine. Every piece of memory i had was A-ok. I thought i'd get a third PC involved for a final say. I ran the memtest again (mulitple passes each time mind you) and again no errors.
I came here to see if anyone else had a similar problem, and yeah. But no solution for me. This is pretty much my hail-mary. I'd really like help from someone more knowledgeable than myself. I really do not want to buy a new mobo, but WoW is a subscription game...i'd really like to play it as well as edit video, or record stuff with my video card.
If you have any solutions for me PLEASE, I really need help. Thank you for taking the time to read this.

ConeJodc, it's not your memory. Some will tell you it's your pwr supply, some will tell you to change your ddr voltage... it's none of that. This mobo is crap in my opinion because it's got the VIA name on it. Everything I've ever owned that had a VIA chipset eventually blew up (usually it was crap to begin with).
See my latest update in my post regarding this motherboard.
https://forum-en.msi.com/index.php?topic=79880.0
The same memory that tested bad in my PT880 Neo-FSR runs perfectly fine in my new 865PE Neo2.
Return it if you can and get the intel based 478 board.
VIA =
Intel =

[VIA Series] PT880 NEO-FSR

Hi Everyone, I nned your help!!! I have a Intel PIV Prescott 2.4GHz, 533 1MB Cache, 512Mb Ram, 120Gb Hard, and a MSI 16X Burner + 1 MSI PT880 Neo-FSR (601-7043-020) and a MSI FX5200-TD128 (LE) Video Card and the problem is that working under Windows XP I´m having terrible problems and blue screens sayin things like this:
DRIVER_IRQL_NOT_LESS_OR_EQUAL
Technical Situation:
STOP: 0x000000D1 (0x0a060016, 0x00000002,0x00000000,0xffecc216)
Portcls.sys_address F7ECC216 BASE AT F7ECB000 DATE STAMP 41107F13
and other screens that I couldn´t write them down.
Before I bought this PIV, I was usin a K7N2Delta + Athlon 2600+ and I never had this problems!!! So I dont know what to do... Please HELP ME !!!!
Thanks !!!!
Marcelo Siciliano From Argentina - Buenos Aires

Hi again !!! Aicom I´m using a 512 mB DDR Markvision Pc 3200 400Mhz RAM Moduile....
I Think that maybe the problem should be in the compatibility between thwe MOBO and the Video Card... MSI FX5200
Please If U have any Data at all, please let me know...
Thanks from Buenos Aires, Argentina...
Bye

[VIA Series] PT880 Overclocking Issue

Well i can't Overclock as high as i thought i could i can overclock to 3.6 but thats nearly stable any higher then i have to reboot i was thinking of a bios degrade from 1.9 - 1.7 i herad 1.7 unlocks multiplyers so im thinking that that could help my overclocking issue and plus on top of that i can't raise my CPU V Core only my DDR and AGP south Bridge and North Bridge and thats it i found out that overclocking on Factory settings got me a higher overclock and putting the divder and 6/5 166Mhz. Any Ideas on higher overclocking i have a Nice cooler Thermal Take Spark 7+ maybe artic silver 5 would help and well heres my specs-
Intel Pentium 4 3.2E Prescott
MSI PT880 FSR Board (7043)
1 Gigabyte Kingston Hyper X (Dual Channel)
GeForce 4 MX 420 64 Meg (4X)
60 Gigabyte Maxtor Sata
and alot of case fans
350 Watt Power Supply Stock

Hi,
The Prescott is dynamic voltage, therefore you cannot "SET" volltage.
If you are going to "play" with North and South Bridge voltages..........get a heatsink for south bridge!!!!!!!!!!!!!!!!!!
You should post in OVERCLOCKING part of Forum. You may receive better support there.
Del

[VIA Series] PT880 Neo - 2 dead PCI slots?

Scanning through the forums, I didn't see anything relevant so here goes.
I bought my board not too long ago and have been slowly adding peripherals to my system. I try to spread things out when choosing a PCI slot for a new card. Well, looking at my sig, I have discovered that two of my PCI slots are dead.
When I say dead, I mean that I'll install a card there (previously never installed), boot up to Windows, and wait for the Found New Hardware dialog. I think that this is slightly broken, so I go to the Device Manager and none of my new items show up with uninstalled or installed drivers. I crack my case, move the card to one of the working slots, and everything is dandy.
For the record, I refer to PCI 1 as the closest PCI slot to the AGP slot (most central physically on the motherboard). Inheritently, PCI 5 is the slot closest to the corner of the motherboard. I am having problems with slots 2 and 3.
I am hoping that there is a dip switch or a rule similar to memory slot usage that will fix this problem. I have not found a solution yet and am hoping that someone here can help.
Thanks.

Update the BIOS, clear the CMOS, if ur problem is not solved, RMA the mainboard.

[VIA Series] PT880 Neo-FSR hangs during POST after connecting USB device

I "successfully" built a new machine from scratch for the first time. Windows 2000 was installed and working with updates. I connected an iPod to a USB port (during the iTunes software installation) and the machine froze. After a power cycle, the machine will not successfully boot. After the fact, I discovered that the grounding wires on the USB2 connector were no longer connected. I'm not 100% sure that I plugged the iPod into the USB ports connected to USB2, but that's a good assumption.
On reboot, the screen starts normally. When the line "DEL: Setup F11: Boot Menu F12:Network Boot TAB: Logo F10: Flash Recovery" appears, the machine stops. The next line reads "Flash Recovery". The D-Bracket2 indicator lights stop at "Testing Base and Extended Memory".
I'm unable to select any of the options to enter the BIOS setup, etc. I tried clearing the CMOS data using the jumper and I now get the logo screen, but the system still hangs with the same D-Bracket2 lights.
I do not have any spare memory, so if I need to swap it out for diagnostics, I'll have to go shopping.
Is there any way to salvage this board or did I permanently fry it?

No luck on entering BIOS or getting graphic screen to clear.
To clarify, I cleared the CMOS in despiration after the system hung and I couldn't get into BIOS. I don't remember all the details from the original screen (before it was obscured by the graphic!), but I know that there was no "error message" per se. Everything appeared normal except that "Flash Recovery" appeared an additional time below the "DEL: Setup..." line. Before clearing the CMOS, I had no apparent response from any key. (DEL, F10, F11, F12, etc.)
I'm inclined to assume that I managed to actually fry something on the board, but I'm hoping to get that confirmed before buying a replacement.

Can't install HP Color LaserJet 2600n to my new macbook pro with Yosemite ? Message error : "Can't download the software because of a network problem."

Hello,
I'm trying to install my HP Color LaserJet 2600n (USB) to my new macbook pro with Yosemite ? It detects the printer but when I try to install it, I get the message error : "Can't download the software because of a network problem."
I tried to install the software via the HP website. It's not working.
Can someone help me with this one ?
Thanks,

HP Print Drivers

Upgrading OS Mountain Lion - Network problems

Dear all,
I've upgraded my iMAC last week-end. Good job
But... big network problem with ADSL connexion via ethernet
I've installed a CPL network at home because WI-FI range is blocked by big walls. Then no problem before (Modem Belkin connected on time machine and all devices (apple tv, Imac,...) linked by CPL).
WHen I've installed Moutain Lion, no more possibilities to connect throughout Ethernet (no DHCP renew).
Then I've reloaded a WIFI connexion. No problem at this time since this morning. I need to disconnect and reconnect the connection 4/5 times and It's no stable ?
Do you have an advice ? I really would like to find the stability of a CPL-Ethernet connection.
Thanks

If you have more than one user account, these instructions must be carried out as an administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Enter the word "Starting" (without the quotes) in the String Matching text field. You should now see log messages with the words "Starting * backup," where * represents any of the words "automatic," "manual," or "standard." Note the timestamp of the last such message. Clear the text field and scroll back in the log to that time. Select the messages timestamped from then until the end of the backup, or the end of the log if that's not clear. Copy them (command-C) to the Clipboard. Paste (command-V) into a reply to this message.
If there are runs of repeated messages, post only one example of each. Don't post many repetitions of the same message.
When posting a log extract, be selective. Don't post more than is requested.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Some personal information, such as the names of your files, may be included — anonymize before posting.

Nokia Trailers 1.3.31 - Network Problem, N8 Belle

Hi,
Updated to Nokia Trailers 1.3.31 a couple of days ago and as soon as I did the app no longer starts. Instead, I get "Network problem" and then it shuts down.
I've uninstalled and reinstalled the app to no avail.
Network is fine, wifi and 3g, all other apps (mail, fb, twitter, maps, foursquare, store, cutebox, etc) are working, so what's up with Trailers?
Attachments:
Scr000032.jpg ‏54 KB

Fixed the problem with Trailers on my N8 last night by doing a format, hard reset and firmware reinstall via Nokia Software Updater.
This also fixed the problem I was having with Google Maps, Nokia Drop and Maps voice guidance via bluetooth to the car stereo.
Happy days!

Creating Wireless Network via existing Ethernet Network

Hello
I have a problem with setting up my network in my new place, where internet was already available via existing Ethernet network. I tired to solve the problem with the Designing Networks with Airport but I think my case is not described there. First of all let me describe how the Ethernet works. Network is setup by a Modem/router device that was supplied from the ISP, it is connected to the switch that divides the service over 4 different apartments, since it is a quite good connection there is no bandwidth problem, but the ISP device assigns only 5 IP addresses that can get internet service, everything above 5th IP is just an IP without Internet. From my basic knowledge I think that i need at least 4 IP to cover my needs. Time Capsule, Mac book, iTouch and my xbox. IF i set up my TC into a bridge mode it all works, but i am taking to much internet IP's and my neighbors are stuck with the IP's that don't allow them to connect to internet. What I need to know is a detailed instruction how to use one IP address from the 5 available, and using time capsule provide local IP to all of my devices at home so the rest of IPs generated by the ISP device will not be assigned to me.
I tired to set up the time capsule to option Share a public IP address, or static IP's option, but in both cases my devices fail to connect to internet, however they do have assigned IP's by the TC. I have a strange feeling there is a small detail I am missing that keeps me from a successful set up, but of course I might be wrong, because I am relatively new in Mac community and have only basic knowledge in network stuff.
I am sure that I was not the only one that has this problem so if there is another topic about this subject, which I have failed to find, I would appreciate a link. Thanks for help in advance, if any other info is required please don't hesitate to ask, hopefully I can solve my problem with Your help very soon.
Regards

+my Xobox fails to connect to xbox live claiming that I have NAT set as moderate (the NAT map porting is enabled) and I dont know what to do about that. I have googled a bit and there are some suggestions that my TC puts additional layer of NAT on top of my ISP modem/router and that's why it is confused.+
As William has pointed out, in your particular setup, there may be no way around the double layer of NAT. The Time Capsule must be set to "Share a single IP address" if you want to connect multiple devices.
Might be worth confirming that you really do have the additional NAT layer on your network.
Open Hard Drive > Applications > Utilities > Network Utility
Click on the Traceroute tab
Enter an address like "www.mac.com" (without the quotation marks) in the box
Click Trace
Let the trace run for a minute or two and then click Stop
Look at Line 2 only in the log.
If you see a 192.168 or 10.x.x.x address in this line, you have the additional NAT layer on your network.
If that's the case, I'm afraid that the only way to eliminate the NAT service on the Time Capsule is to place it in "bridge" mode. But, I understand that you have limited IP addresses to work with there.
Any way to have more IP addresses authorized for that location? That would appear to be the only solution if you want the Xbox to connect to Xbox live.

LaCie MiniHD connect network problem

I have a LaCie MiniHD connect in my local network. Did everything LaCie told me to do so I could write to the USB attached LaCie drive.
Formatted the drive in OS X EXtended but not journalized.
Tried to connect via smb://MiniHD.smb.tcp.local and the network told me to enter my ID and Password, I don't know why.
So I brought back the disk drive to my mac and changed the whole drive permission to read and write for everyone.
Brought back the drive to my TV and now I could transfer anything from my mac to the drive.
I was glad of that, but having shut down the drive and the MiniHD connect, when I opened it again to transfer something from my mac to the drive, I still got the same problem again with the same message.
"One or more elements cannot be copied to "LaCie_750" because you don't have the permission to read. Do you want to copy the elements you are authorized to read."
I suspect the software on the Lacie MiniHD connect to block OS X when it initialises the drive on startup.
In particular I see a folder named _HF2VN~W appearing in the root level of the drive.
Can any one help me with thi samba network problem on Mac OX 10.6.5?

I have since had a reply from LaCie to say that this issue has been identified and is being worked on - however I'm afraid that I don't have any timeline for when this will be fixed.

Uploading using Adobe Premiere Elements 12 Network problems

Hi,
Is there a place in Adobe Premiere Elements 12 that we can insert our company proxy details, the reason being. When I go to Publish and Share and click "Social Websites" and want to upload a video to youtube and push next it gives the following error "Online Services encountered an error. The services will be terminated or paused if possible."
If I use a 3G card it allows us to upload. Our network must be blocking this link or programme, yet we have made sure from our side adobe is not blocked on the network and I have access to all websites.
My question is can we insert proxy details somewhere or can I get the link of where that link is taking us to when pushing next trying to upload with youtube via adobe . I know it is going to youtube but I need the exact URL to make sure we allow this link to work.
Anyone have the answer for me?

MaudeSt
This is not Adobe. Rather user to user. For network problems when using the current version which is now Premiere Elements 12, please contact Adobe via its Adobe Chat.
Click on the following link, and then find and click on Chat Panel to discuss
Premiere Elements
Downloading, Installing, Setting Up
Downloading, Installing
Chat Panel
Contact Customer Care
I have set the web page to the Chat Panel level. If it does not hold the setting, then you will need to navigate to Adobe Chat using the topics
above as guidelines. If you end up seeing only Ask the Community instead of Chat Panel, then try again later. Chat has been having in times
when it is unavailable due to updating. It is an on and off situation lately. Chat has the option to do remote control of your computer for
troubleshooting purposes. We do not.
At the moment that I am hitting the "Add Reply" for this post, only Ask the Community option is being displayed at the Adobe Chat contact link.
Please let us know the outcome.
Thank you.
ATR

[VIA Series] pt880 network problems

Similar Messages

Maybe you are looking for