Vibration specification of the 6500 serie switch

We are doing heavy contruction work near an important network room and we want to know what kind of vibration the 6509 switch can tolerate. In the specsheet (http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/hardware/Chassis_Installation/Cat6500/6500_ins/01over.html), there are vibration specifications but it is unclear what is the permitted level during operation. I guess the vibration section is what I'm looking for:
Operational—3 Hz to 500 Hz,
Power Spectral Density (PSD)—0.0005 G2/Hz at 10 Hz and 200 Hz. 5 dB/octave roll off at each end. 0.5 hours per axis (1.12 Grms).
I believe that the specified value refers to a test that is done on the unit (using in the specified PSD shape). The test is repeated in each axis for 0.5 hour. What about the 1.12Grms? I though it would be the sqare root of the intregration of the PSD from 3 to 500 Hz, but it doesn't seem to add up.
That being said, would it be right to use the PSD shape a the vibration limit not to go over?
thank you.

Similar Messages

How to remove the WiSM2 from the Catalyst 6500 series switch?

Hello, can you explain to me how to safely remove the WiSM2 from the Catalyst 6500 series switch?
According to the documentation "Catalyst 6500 Series Wireless Services Module 2 Installation and Verification Note":
To remove the WiSM2, perform these steps:
Step1     Shut down the module by one of these methods:
In privileged mode from the router prompt, enter the hw-mod module mod shutdown command. NoteIf you enter this command to shut down the module, you must enter the following commands in global configuration mode to restart (power down, and then power up) the module:
Router# no power enable module modRouter# power enable module mod
If the module does not respond to any commands, press the SHUTDOWN button located on the front panel of the module.
Step2     Verify that the WiSM2 shuts down. Do not remove the module from the switch until the POWER LEDis off.
But, in the case of Step1 (1st methods) I do not see a option "shutdown" in the command "hw-mod module 3"...
All I prompted to enter is:
c6500#hw-module module 3 ?
boot           Specify boot options for the module through Power Management Bus control register
reset          Reset specified component
simulate Simulate options for the module
Is it hidden options? IOS version of c6500 is 12.2(33)SXJ1
In the case of Step2 (2nd methods) there is not any button on the front panel of the module?
And yet, it is better to remove the module configuration manually or use the command module clear-config prior to removing the module?

Good catch.
Which one is true, will get back to you on this if i've something soon.
http://www.cisco.com/en/US/docs/wireless/module/wism2/installation/note/WiSM_2.html#wp34727
The above link is procedure to remove wism2. This procedure doesn’t look like wism2 is hot swapable.
http://www.cisco.com/en/US/docs/wireless/module/wism2/installation/note/WiSM_2.html#wp34621
All modules, including the supervisor engine (if you have redundant supervisor engines), support hot swapping. You can add, replace, or remove modules without interrupting the system power or causing other software or interfaces to shut down. For more information about hot-swapping modules, see the Catalyst 6500 Series Switch Module Installation Guide.

Multicast in 6500 series switch

We have one customer who have config Ipsec over GRE end to end for all remote locations.Now customer want to upload large file to all remote locations.So we have to config multicast in our backbone network.
We have 6500 Series Switch thorough which all routing is done.But how multicast traffic will flow thorough IPsec tunnel.Is any one having such case pls let me know.
TIA
Regards
SAM

check out the following link Multicast over IPsec VPN Design Guide, this should help :
http://www.cisco.com/application/pdf/en/us/guest/netsol/ns656/c649/cdccont_0900aecd80402f07.pdf

APs unable to receive IP address from DHCP (core 6500 series switch)

Dear Friends,
a week ago I had stable wireless network APs were getting IPS from 6500 series switch (DHCP) but unfortunately some WISM got rebooted and now APs are unable to receive IP address from Core 6500 DHCP, to cater this issue I have another DHCP server configured on windows 2008 i created another subnet and and put APs in that vlan now all APs are are successfully receiving IPS from windows DHCP server I don't know why APs are not able to receive IPs from core 6500 series DHCP.
please advice
Thanks
Faysal

Thanks george for stepping up here is DHCP config
ip dhcp excluded-address 10.10.30.1 10.10.30.20
ip dhcp excluded-address 10.10.8.1 10.10.8.10
ip dhcp excluded-address 192.168.10.1 192.168.10.5
ip dhcp excluded-address 10.9.20.1 10.9.20.30
ip dhcp pool vlan_30
network 10.10.30.0 255.255.254.0
default-router 10.10.30.1
option 60 ascii """"""""""""""""""""""""CiscoAPc1250""""""""""""""""""""""""
option 43 hex f110.0a0a.1e0b.0a0a.1e0d.0a0a.1e0f.0a0a.1e11
dns-server 10.10.2.11
lease infinite
ip dhcp pool WiSM1_SP
network 192.168.10.0 255.255.255.248
default-router 192.168.10.1

What's the password to logon the 3560 series switch on express setup

what's the password to logon the 3560 series switch on express setup

Hi Samuel,
The 3560 doesn't have a password configured on it by default. You may want to double check the procedure for accessing Express Setup in case a step was missed:
http://www.cisco.com/en/US/partner/docs/switches/lan/catalyst3560/hardware/quick/guide/3560gsg_08.html#wp49930
If that still doesn't work, you can reset the switch to factory defaults by following this guide:
http://www.cisco.com/en/US/partner/docs/switches/lan/catalyst3560/hardware/quick/guide/3560gsg_08.html#wp46478
Hope that helps.
-Mike

5508 WLC-6500 Series Switch Etherchannel

Hi,
I have a 5508 controller connected to a 6500 VSS pair. Below is the port channel configuration and port configuration. I am just wondering whether we still have to configure a load balancing method as cisco recommends “port-channel load-balance src-dst-ip” as best practice.
Does this still applicable for 5508 controller-6500 Series uplink as the etherchannel is L2 etherchannel?
Port Channel Config:
interface Port-channel1
description To 5508 WLC
switchport
switchport trunk encapsulation dot1q
switchport trunk native vlan 9
switchport trunk allowed vlan 10,11,12
switchport mode trunk
mls qos trust dscp
end
Interface Config:
interface GigabitEthernet1/1/42
description To 5508 WLC
switchport
switchport trunk encapsulation dot1q
switchport trunk native vlan 9
switchport trunk allowed vlan 10,11,12
switchport mode trunk
wrr-queue bandwidth 5 25 70
wrr-queue queue-limit 5 25 40
wrr-queue random-detect min-threshold 1 80 100 100 100 100 100 100 100
wrr-queue random-detect min-threshold 2 80 100 100 100 100 100 100 100
wrr-queue random-detect min-threshold 3 50 60 70 80 90 100 100 100
wrr-queue random-detect max-threshold 1 100 100 100 100 100 100 100 100
wrr-queue random-detect max-threshold 2 100 100 100 100 100 100 100 100
wrr-queue random-detect max-threshold 3 60 70 80 90 100 100 100 100
wrr-queue cos-map 1 1 1
wrr-queue cos-map 2 1 0
wrr-queue cos-map 3 1 4
wrr-queue cos-map 3 2 2
wrr-queue cos-map 3 3 3
wrr-queue cos-map 3 4 6
wrr-queue cos-map 3 5 7
mls qos trust dscp
channel-group 1 mode on
end

Hello,
Please check to following link regarding load balancing between 5508 and WLC 6500:
http://www.learnios.com/viewtopic.php?f=5&t=34555

Where is the 300 series switch with 48 gigabit ports and PoE?

Love the 300 series but surprised that Cisco did not put out a 48 port model with gigabit and PoE. Would love to hear from Cisco on the reasoning behind that and if there are any plans to introduce one? Given that gigabit and VoIP is the future at many companies it only makes sense.

The switches use the SFPs to link to each other. The SG500 has ports for 1G or 5G and the SG500X has 10G ports. Whichever port you select will be the speed at which the switches pass traffic and stack control information. These same ports can be 'reclaimed' if you were to set the switch to stand alone mode. I have put a chart below which details the ports you can use and the speed of these ports.
Header 1
Header 2
Header 3
Header 4
Header 5
Units in Stack
SG500X
SG500X
SG500
SG500
Stack Port Name
S1,S2-XG
S1,S2-5G
S1,S2
S3,S4
Stack Port Speeds
10G/1G
1G/5G
1G
1G/5G

Switch support for NAC CCA for 6500 series switch

per the 4.0 document "switch support for Cisco NAC" there is a note that says
Catalyst 6000/6500 on IOS do not support mac-notification
Does this mean you cannot deploy layer 2 OOB mode, as snmp notification to the CAM will not happen with the 6k platform?

Probably, the configuration guide will give you better idea about your problem.
http://www.cisco.com/en/US/products/hw/switches/ps708/products_configuration_guide_book09186a00803f5611.html

Any one ever worked on 6500 series Cisco switches QOS or 6503 or 6524 QOS(Urgent help needed)

Hi All,
I am having issue specifally doing QOS configuration on 6503 or 6524 or 6509 switches. I am unable to match any EF(voice) traffic for eompls(vlan based) on 6503 cisco switch. If i use any other router as 2811 or 2821 my QOS configuration works perfect but if i put 6503 as PE2 it does not work.i am using vlan based eompls.
Below is the scenario & configuration which i am having issue.
CE1(2821 router)(dot1Q)--------->PE1(2821 router)------->P(6524 switch)-------->PE2(6503 switch)------->(dot1Q)(2821 switch)CE2.
On CE1 i can match ip-precedence 5 traffic and mark that traffic to cos5 on outbound port.On PE1 i can match cos5 packet and mark with mpls exp top5 on inbound port, on outbound port i can match mpls exp 5.
On PE2(6503) i am unable to match that mpls exp5 packet on inbound port. none of the configuration worked on 6500 series switches with mls qos, ,mls qos trust dscp,mls qos trust cos etc. Although i can match cos5 traffic on CE2 on inbound interface.i can not match mpls exp 5 traffic on 6503 and all i can see traffic as default-class on 6503 switch. I tried many things and many configurations on 6503 but nothing worked.If i put 2821 router as PE2 instead of 6503 my qos configuration works. but why if i put 6503 my same qos configuration does not work?
---match means=classification or classify
Can anyone tell me how qos works on 6500 series switches or where i am having issue in my scenario.
i am using this ios on 6503: s72033-advipservicesk9_wan-mz.122-33.SXI3.bin.
below r my questions for 6503 qos:
1.do i need to use some other map tables,am i using correct map tables on 6503 as cos-dscp,dscp-cos,exp-dscp etc.
2.any other configutaion of qos needed on 6503?
3.i am unable to match anything on outbound port of 6503.
4.on 6503 i am using sup720 and PFC3BXL.any specific configuration needed for PFC3bxl.
5. 6503 not allowing me to match qos-group on inbound interface, not allowing me to set cos5 on outbound interface. not allowing me to set cos5 as an inbound interface.
CE1(2821) config:
class-map match-any EF
match ip precedence 5
class-map match-any data
match ip precedence 3
policy-map ip2mpls
class EF
set cos 5
class data
set cos 3
interface FastEthernet0/0
no ip address
duplex auto
speed auto
interface FastEthernet0/0.455
encapsulation dot1Q 455
ip address 172.16.15.1 255.255.255.252
service-policy output EF
PE1(2821) config:
mls qos map cos-dscp 0 8 16 24 32 40 48 56
class-map match-all exp_3
match mpls experimental topmost 3
class-map match-all mpls_exp
match mpls experimental topmost 5
class-map match-any cos3
match cos 3
class-map match-any LOO1
match cos 5
policy-map EF
class LOO1
set mpls experimental imposition 5
class cos3
set mpls experimental imposition 3
policy-map QOS_G_5
class mpls_exp
priority
class exp_3
bandwidth 500
interface Loopback0
ip address 3.3.3.3 255.255.255.255
interface FastEthernet0/0
ip address 192.168.23.2 255.255.255.0
ip ospf network point-to-point
duplex auto
speed auto
mpls ip
service-policy output QOS_G_5
interface FastEthernet0/1.455
encapsulation dot1Q 455
xconnect 5.5.5.5 455 encapsulation mpls
service-policy input EF
PE2(6503 qos):
R1#show module
Mod Ports Card Type Model Serial No.
1 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE SAL09401U2L
2 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL114247YN
3 16 16 port 1000mb GBIC ethernet WS-X6416-GBIC SAL0712AM69
4 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL10019J4N
5 2 Supervisor Engine 720 (Hot) WS-SUP720-3BXL SAD102805VM
6 2 Supervisor Engine 720 (Active) WS-SUP720-BASE SAD0846060F
Mod Sub-Module Model Serial Hw Status
1 Distributed Forwarding Card WS-F6700-DFC3BXL SAD102504EF 5.3 Ok
2 Centralized Forwarding Card WS-F6700-CFC SAD111300PD 3.1 Ok
4 Centralized Forwarding Card WS-F6700-CFC SAL1004BQ2A 2.0 Ok
5 Policy Feature Card 3 WS-F6K-PFC3BXL SAD10270189 1.8 Ok
5 MSFC3 Daughterboard WS-SUP720 SAD102801G5 2.5 Ok
6 Policy Feature Card 3 WS-F6K-PFC3BXL SAL1415FE95 1.11 Ok
6 MSFC3 Daughterboard WS-SUP720 SAD08440794 2.4 Ok
R1#show mls qos maps
Normal Burst Policed-dscp map: (dscp= d1d2)
d1 : d2 0 1 2 3 4 5 6 7 8 9
0 : 01 01 02 03 04 05 06 07 08 09
1 : 10 11 12 13 14 15 16 17 18 19
2 : 20 21 22 23 24 25 26 27 28 29
3 : 30 31 32 33 34 35 36 37 38 39
4 : 40 41 42 43 44 45 01 47 48 49
5 : 50 51 52 53 54 55 56 57 58 59
6 : 60 61 62 63
Maximum Burst Policed-dscp map: (dscp= d1d2)
d1 : d2 0 1 2 3 4 5 6 7 8 9
0 : 00 01 02 03 04 05 06 07 08 09
1 : 10 11 12 13 14 15 16 17 18 19
2 : 20 21 22 23 24 25 26 27 28 29
3 : 30 31 32 33 34 35 36 37 38 39
4 : 40 41 42 43 44 45 46 47 48 49
5 : 50 51 52 53 54 55 56 57 58 59
6 : 60 61 62 63
Dscp-cos map: (dscp= d1d2)
d1 : d2 0 1 2 3 4 5 6 7 8 9
0 : 00 00 00 00 00 00 00 00 01 01
1 : 01 01 01 01 01 01 02 02 02 02
2 : 02 02 02 02 03 03 03 03 03 03
3 : 03 03 04 04 04 04 04 04 04 04
4 : 05 05 05 05 05 05 05 05 06 06
5 : 06 06 06 06 06 06 07 07 07 07
6 : 07 07 07 07
Dscp-exp map: (dscp= d1d2)
d1 : d2 0 1 2 3 4 5 6 7 8 9
0 : 00 00 00 00 00 00 00 00 01 01
1 : 01 01 01 01 01 01 02 02 02 02
2 : 02 02 02 02 03 03 03 03 03 03
3 : 03 03 04 04 04 04 04 04 04 04
4 : 05 05 05 05 05 05 05 05 06 06
5 : 06 06 06 06 06 06 07 07 07 07
6 : 07 07 07 07
Cos-dscp map:
cos: 0 1 2 3 4 5 6 7
dscp: 0 10 18 24 34 46 48 56
IpPrecedence-dscp map:
ipprec: 0 1 2 3 4 5 6 7
dscp: 0 8 16 24 32 40 48 56
Exp-dscp map:
exp: 0 1 2 3 4 5 6 7
dscp: 0 8 16 24 32 40 48 56
mls netflow interface
mls qos map cos-dscp 0 10 18 24 34 46 48 56
mls qos
class-map match-all exp_3
match mpls experimental topmost 3
class-map match-all EXP_5
match mpls experimental topmost 5
class-map match-all QOS_GROUP_5
match qos-group 5
class-map match-all prec5
match ip precedence 5
class-map match-all cos5
match cos 5
policy-map mpls2ip
class QOS_GROUP_5
set cos 5
policy-map IN_FROM_R3
class EXP_5
set qos-group 5
interface Loopback0
ip address 5.5.5.5 255.255.255.255
interface GigabitEthernet2/2
mls qos trust cos
or <------------ (tried both individually but none worked)
mls qos trust dscp
interface GigabitEthernet2/2.455
encapsulation dot1Q 455
xconnect 3.3.3.3 455 encapsulation mpls
service-policy output mpls2ip
interface GigabitEthernet2/1
ip address 192.168.34.4 255.255.255.0
ip ospf network point-to-point
mls qos trust cos
or <------------ (tried both individually but none worked)
mls qos trust dscp
mpls ip
service-policy input IN_FROM_R4
Thanks & regards,
Ahsan Rasheed

Hi All,.
I am still having issue on 6503 or 6524 Cisco Switch.
" Can any one give me any sample of 6524 or 6503 QOS working configuration, i would be really thankful "
As i have mentioned in my prevoius post of configuration of 6503. I am unable to match mpls exp 5 packet on 6503. My qos configuration on PE1(2811 router) is working perfectly. I am unable to classify mpls ex5 or mpls exp3 on 6503 switch. Am i missing something on configuration?
PE2 config:"6503 switch"
class-map match-all mpls_exp
match mpls experimental topmost 5
policy-map EF
class mpls_exp
R!#mls qos
int Gi2/4
service-policy input EF
mls qos trust cos
dscp: 0 10 18 24 34 46 48 56
Exp-dscp map:
exp: 0 1 2 3 4 5 6 7
dscp: 0 10 18 24 34 46 48 56
Thanks,
Ahsan Rasheed

Maximum 29XX switches on a 6500 series

Hello,
is there a recommended maximum of user ports i can connect directly to a 6500 series core switch?
So I have a situation with about 80 24-ports switches (in stacks of 2 or 3) connected with fiber to the core switch. Now one of the network managers states we need a distribution layer cause performance in the 6500 will drop. Reason for this is that the 29XX series switches do not support layer 3.
Is this correct? And does the added layer 3 functionality in a (extra) distribution layer increase performance in the core? Even though almost all traffic is user - server traffic and servers are connected to core?
Anyone know? THanks!

Hi Friend,
Which sup engine do you have and is there any switch fabric module you are running. Cat6500' are cross-fabric chassis which gives 32GBPS backplane switch capacity bedefualt. If you have SFM (switch fabric module) installed then it will give 256 GBPS of backplane capacity.
If you are running Sup720, you have 720 GBPS backplane capacity and you will see a greater performance by cat65K.
If you dont have SFM or sup 720, then yes with direct access switches uplink to Core might slow down the performance of the core switch.
If that's the case I would suggest to got for hierarchical design and add another layer of the architecture i.e distribution layer.Now what you can do with this additional layer, is that you can uplink your access layer to it, have your inter-vlan routing done on thius layer, have to access control policy deployed at this layer.
This addtion layer and the above functionalities will off load the processing of traffic at core and core will be efficient enough to process the traffic as fast as it can. This is a abosultely correct approach.
Please, write back for any qurstions.
HTH, Please rate if it does.
-amit singh

Flash file location in 6500 Core switch

Hi ,
Please guide me what is location of flash file in 6500 Series switch and how can we take back of IOS image for 6500 series.
Thank you

You're welcome.
People seldom backup the actual IOS image binary file since it is usually just as easy to pull a new copy from cisco.com.
The more useful file is the running-config. You can most easily get a one time copy of that by just setting terminal length to 0 ("term len 0"), turning on logging on your shell tool and then typing "show run". The log file will now have a local copy of your running-config. You can also copy it via the cli using tftp, ftp, scp etc. transport methods.
Many open source and commercial products also allow you to automate that whole process for many devices. RANCID, Kiwi CatTools, SolarWinds NCM, Cisco Prime LMS, etc. all do that (and much more).
Please rate helpful posts and mark your question as answered when it is.

Traceroute and Ping from GUI on 300 series switches?

Any hopes of being able to do Pings and Traceroutes from the GUI? It's a little frustrating having to telnet/ssh to do those basic things.
It would also be nice to be able to switch to Layer3 mode through the web GUI.

Hi,
Thank you for participating in the Small Business support community. My name is Nico Muselle from Cisco Sofia SBSC.
With pleasure I can announce that the ping and traceroute function will be available in the next firmware release of the Sx300 series switches. Changing the system mode however is not (as far as I know). The firmware to be release will contain major updates and addition of functions like TextView (command line interface), CDP, smartports, QinQ etc ...
A little patience before this maintenance release is available, it will be certainly worth waiting for !
Best regards,
Nico Muselle
Sr. Network Engineer - CCNA

SSH on SG200 series switches

Community,
Can someone tell me what the intention behind adding SSH to the SG200 series switches was. Is it to allow SCP copies to and from the switch for configuration and firmware updates OR is it to allow CLI access to the switches.
I have tried to SSH to the switch using PuTTY from Windows and native SSH from Linux/Unix clients, but nothing happens.
Is there some other area of configuration to enable communcation via SSH?
Thanks.

Hi, any access feature would be under security -> tcp/udp services
SSH, telnet, etc is not included there.
The only SG200 switch which supports a CLI is the SG200E models (which has supported CLI for as long as I can remember , at least 2 yrs).
Please reference the documentation, Chapter 18 start page 276.
http://www.cisco.com/en/US/docs/switches/lan/csbss/sf20x_sg20x/administration_guide/78-21139.pdf
As far as I can tell this is for things like Secure Copy.
There is also CLI information in chapter 19, here's the excerpt. This is in context with SSD.
The Menu CLI interface is only allowed to users if their read permissions are Both
or Plaintext Only. Other users are rejected. Sensitive data in the Menu CLI is always
displayed as plaintext.
Password recovery is currently activated from the boot menu and allows the user
to log on to the terminal without authentica
tion. If SSD is supported, this option is
only permitted if the local passphrase is identical to the default passphrase. If a
device is configured with a user-defined passphrase, the user is unable to activate
password recovery.
-Tom
Please mark answered for helpful posts

Are the SG500P SMB switchs supported for Cisco Network Assistant?

Hi, we need to enroll some SG500-28P switches to a CNA? Is this possible? I suppose that CDP feature allow this. Actually, i have installed CNA Ver. 6.0. Thanks in advance.

Hello Fernando,
Thank you for visiting the Cisco Support Community!
Here is a list of all the devices supported by the Cisco Network Assistant for the 6.0 version and later. Many of the 500 series switches, including the SG500-28P Managed Switch, are supported by the CNA. This page will also give you any additional information you may need such as the features of the CNA 6.0 version, any system requirements, and more.
If this post was helpful, please remember to mark this question as resolved to help others in the community! If you have any further questions, please do not hesitate to ask!
Best,
LP

Firmware upgrade question for 300 series switches

Hi-
I have a customer that is investigating a strategy and solution for centralized firmware management of the 300 series switches. They have found an issue in the lab where they were trying to roll back the firmware to a previous version They can not roll back to the previous firmware version, which is desirable in the case of finding an issue in the new firmware that causes them to have need to rollback to a known working version.
We have read in the cisco 300 switch admin guide that there are two images (active and inactive) and that a new downloaded firmware always replaces the inactive image and is active until explicitly set. The admin guide does not mention inability to make an older firmware image as active image when the switch has previously run on a new release firmware image. My customer's engineers testing have informed me that an older image can not be made active after a newer image has booted. Can you please verify if this if a fallback is supposed to work as it is causing a lot of concern-
Thanks-
Jena

Jena,
The release notes -
http://www.cisco.com/en/US/docs/switches/lan/csbms/sf30x_sg30x/release_notes/Sx200-Sx300_R1.1.2.x.pdf
What firmware is the switches currently on?
Major Changes and Defects Corrected
• Hardware version 1.0 devices that were upgraded to software version 1.1
can now be downgraded to software version 1.0. You must delete the
startup configuration file before rebooting the device to software version
1.0. Otherwise the device may have problems when booting up. You may
backup your running configuration before the reboot, and re-import the
configuration afterward. Major Changes and Defects Corrected
• Hardware version 1.0 devices that were upgraded to software version 1.1
can now be downgraded to software version 1.0. You must delete the
startup configuration file before rebooting the device to software version
1.0. Otherwise the device may have problems when booting up. You may
backup your running configuration before the reboot, and re-import the
configuration afterward.
Please read full release notes for other work arounds
Hope this helps,
Jasbryan

Vibration specification of the 6500 serie switch

Similar Messages

Maybe you are looking for