Vic card not initializing

I have recently got a router - 1751v
and also a voice card - vic-2fxs
The card is not getting initialized
amber light is glowing contineously
error showing card not initializing, unknown hardware found in slot1.
here is the sh tech support details of the router
the card is vic-2fxs
------------------ show version ------------------
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-SV8Y-M), Version 12.2(13)T16, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Thu 14-Apr-05 19:25 by yiyan
Image text-base: 0x80008120, data-base: 0x81190E44
ROM: System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
ROM: C1700 Software (C1700-SV8Y-M), Version 12.2(13)T16, RELEASE SOFTWARE (fc1)
yourname uptime is 4 minutes
System returned to ROM by power-on
System image file is "flash:c1700-sv8y-mz.122-13.T16.bin"
cisco 1751 (MPC860P) processor (revision 0x400) with 83979K/14325K bytes of memory.
Processor board ID FOC08310YEZ (1669471188), with hardware revision 0000
MPC860P processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
------------------ show diag ------------------
Slot 0:
C1751 1FE VE DV Mainboard Port adapter, 3 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 4.0
PCB Serial Number : FOC08310YEZ
Part Number : 73-7241-04
Board Revision : B0
Fab Version : 04
Product Number : Unknown
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 02 4D 41 04 00 C1 8B 46 4F 43 30 38 33
0x10: 31 30 59 45 5A 82 49 1C 49 04 42 42 30 02 04 FF
0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Packet Voice DSP Module Slot 0:
Hardware Revision : 3.2
Part Number : 73-6726-01
Board Revision : A0
Deviation Number : 0-0
Fab Version : 03
PCB Serial Number : VIC09267FBE
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 02
Number of DSP's : 1
DSP memory size(in kwords): 256
Type of DSP : TMS320C549
Product Number : PVDM-256K-4=
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 02 AC 41 03 02 82 49 1A 46 01 42 41 30
0x10: 80 00 00 00 00 02 03 C1 8B 56 49 43 30 39 32 36
0x20: 37 46 42 45 03 00 81 00 00 00 00 04 00 09 02 FF
Packet Voice DSP Module Slot 1:
Not populated
WIC/VIC Slot 0:
Serial 2T (12in1)
Hardware revision 1.0 Board revision D0
Serial number 0024047013 Part number 800-03181-01
FRU Part Number WIC-2T=
Test history 0x00 RMA number 00-00-00
Connector type PCI
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 12 01 00 01 6E ED A5 50 0C 6D 01 00 00 00 00
0x30: 68 00 00 00 00 10 12 00 FF FF FF FF FF FF FF FF
can anyone pls help....

are you sure it is a vic-2fxs and not a vic2-2fxs ?
If so then either a defective card or you may have a counterfeit card (they are out there ) does card have a sticker on it that shows an american flag and made in USA ? if so it is a counterfeit card. If it is a vic2-2fxs you cannot use it in a 1751.

Similar Messages

Voice card not initializing

I have recently got a router - 1751v
and also a voice card - vip2-2fxs
The card is not getting initialized
error showing card not initializing, unknown hardware found in slot1.
is there any patch for the card to be initialized
pls reply

Hi Amit,
Thank you for ur response
here is the sh tech support details of the router
the card is vic-2fxs
------------------ show version ------------------
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-SV8Y-M), Version 12.2(13)T16, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Thu 14-Apr-05 19:25 by yiyan
Image text-base: 0x80008120, data-base: 0x81190E44
ROM: System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
ROM: C1700 Software (C1700-SV8Y-M), Version 12.2(13)T16, RELEASE SOFTWARE (fc1)
yourname uptime is 4 minutes
System returned to ROM by power-on
System image file is "flash:c1700-sv8y-mz.122-13.T16.bin"
cisco 1751 (MPC860P) processor (revision 0x400) with 83979K/14325K bytes of memory.
Processor board ID FOC08310YEZ (1669471188), with hardware revision 0000
MPC860P processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
------------------ show diag ------------------
Slot 0:
C1751 1FE VE DV Mainboard Port adapter, 3 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 4.0
PCB Serial Number : FOC08310YEZ
Part Number : 73-7241-04
Board Revision : B0
Fab Version : 04
Product Number : Unknown
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 02 4D 41 04 00 C1 8B 46 4F 43 30 38 33
0x10: 31 30 59 45 5A 82 49 1C 49 04 42 42 30 02 04 FF
0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Packet Voice DSP Module Slot 0:
Hardware Revision : 3.2
Part Number : 73-6726-01
Board Revision : A0
Deviation Number : 0-0
Fab Version : 03
PCB Serial Number : VIC09267FBE
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 02
Number of DSP's : 1
DSP memory size(in kwords): 256
Type of DSP : TMS320C549
Product Number : PVDM-256K-4=
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 02 AC 41 03 02 82 49 1A 46 01 42 41 30
0x10: 80 00 00 00 00 02 03 C1 8B 56 49 43 30 39 32 36
0x20: 37 46 42 45 03 00 81 00 00 00 00 04 00 09 02 FF
Packet Voice DSP Module Slot 1:
Not populated
WIC/VIC Slot 0:
Serial 2T (12in1)
Hardware revision 1.0 Board revision D0
Serial number 0024047013 Part number 800-03181-01
FRU Part Number WIC-2T=
Test history 0x00 RMA number 00-00-00
Connector type PCI
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 12 01 00 01 6E ED A5 50 0C 6D 01 00 00 00 00
0x30: 68 00 00 00 00 10 12 00 FF FF FF FF FF FF FF FF
can u pls help....

Xd card "not initialized"

I just started getting this error message on the LCD screeen on my Fugi S7000.
"card not initialized"
I have tried clearing the card of all media and am unsure of what to do next.
I have tried to 'repair/restore' it in the disk utility and it comes back as verified and no restoration needed...
Any advice.
I am not sure how to re-initialize this xd card.

waimeagirl:
Check your menu in the Fugi camera for a format option. Every camera will have one. I always reformat my card with the camera after each upload to my Mac. That's the safest way to clear out the card for the next use. Don't use the computer to reformat or erase.
There will be a menu option somewhere for that. The camera's manual should list it.
If you can't fine it you can try MediaRECOVER for reformatting the card. I believe you can use it in demo mode for that. Just not for recovering deleted files.
Do you Twango?
TIP: For insurance against the iPhoto database corruption that many users have experienced I recommend making a backup copy of the Library6.iPhoto database file and keep it current. If problems crop up where iPhoto suddenly can't see any photos or thinks there are no photos in the library, replacing the working Library6.iPhoto file with the backup will often get the library back. By keeping it current I mean backup after each import and/or any serious editing or work on books, slideshows, calendars, cards, etc. That insures that if a problem pops up and you do need to replace the database file, you'll retain all those efforts. It doesn't take long to make the backup and it's good insurance.
I've written an Automator workflow application (requires Tiger), iPhoto dB File Backup, that will copy the selected Library6.iPhoto file from your iPhoto Library folder to the Pictures folder, replacing any previous version of it. You can download it at Toad's Cellar. Be sure to read the Read Me pdf file.

MacPro RAID card not initiating recovery after defective drive replaced

One of my artists is using an Early 2009 Mac Pro on 10.9.5 (13F1077). On Saturday morning, while he was not in the office, Drive 1 warned that SMART was reporting early signs of failure. The RAID card degraded the RAID set. I replaced Drive 1 and marked it as a global spare; but recovery is not initiating. I have, subsequent to installing the drive and marking it as a global spare, rebooted the Mac Pro; but the RAID Utility is not showing any Tasks running, and especially nothing about rebuilding the RAID set. As of now, the RAID set and RAID volume are not available. It appears that I can either try to preserve the data on the drives, or I can attempt to manually rebuild the RAID set; but not both. Unfortunately, the artist had all of his projects on the RAID and had not backed them up to servers at the time of the failure.

If a Disk Fails If a RAID set or volume becomes degraded because a disk has failed, you can use RAID Utility to identify the disk that needs to be replaced.
Note: If your RAID setup includes a spare drive, it is automatically incorporated into the RAID set, and the set switches from degraded to good as soon as the recovery process finishes. If there is no spare, the set will remain degraded until you replace the failed drive, and if a second drive fails before you replace the first, you could lose data.
To replace a failed disk:
1 Open RAID Utility, select the RAID set or volume that is displaying a problem status indicator, and look for a drive bay with a red status indicator. The bay numbers in RAID Utility correspond to the numbered drive bays in your Mac Pro or Xserve.
2 Replace the bad drive module.
3 Use the Make Spare command to set up the new drive as a global spare. If no spare was available when the original drive failed, the RAID card uses the new spare immediately to rebuild the affected RAID set and volumes. If a spare was available at the time of the failure, it is already incorporated into the affected RAID set, and the new spare remains available until it is needed.
https://manuals.info.apple.com/MANUALS/0/MA318/en_US/RAID_Utility_User_Guide.pdf

Runtime error R6025 message after log on to Vista - Flash Card not working

Hi
I'm a newbie & would appreciate any advice.
I am getting a runtime error message R6025 when I log on to Windows Vista.
When I click out of the box I then get a message saying Toshiba Flash Card not working.
I cancel that and my laptop is ok except I don't know if the flashcard is working or not because I don't know what it does.
Sorry if I sound thick
Thanks
Neelie

Hi
I found this MS knowledge base article:
+Description of the R6025 run-time error in Visual C++\+
http://support.microsoft.com/kb/125749
But I doubt this description would be useful for you or anyone here. It describes this error in Visual C++ and this is programming language.
However, I think you should simply reinstall the Value Added Package which you could download firstly from the Toshiba European page.
At first you have to remove the old Value Added Package from the system, then reboot the notebook and follow with new VAP installation.
Bye

What's the difference between a not-initialed object and a null object

hi guys, i wanna know the difference between a not-initialed object and a null object.
for eg.
Car c1;
Car c2 = null;after the 2 lines , 2 Car obj-referance have been created, but no Car obj.
1.so c2 is not refering to any object, so where do we put the null?in the heap?
2.as no c2 is not refering to any object, what's the difference between c2 and c1?
3.and where we store the difference-information?in the heap?

For local variables you can't have "Car c1;" the compiler will complain.That's not true. It will only complain if you try to use it without initializing it.
You can have (never used, so compiler doesn't care):
public void doSomething()
   Car c1;
   System.out.println("Hello");
}or you can have (definitely initialized, so doesn't have to be initialized where declared):
public void doSomething(boolean goldClubMember)
   Car c1;
   if (goldClubMember)
       c1 = new Car("Lexus");
   else
       c1 = new Car("Kia");
   System.out.println("You can rent a " + c1.getMake());
}

GeForce4 TI Video Card Not Recognized Anymore?

For about almost a year, the fan on the GeForce4 TI video card would occasionally make a grinding noise, although it has always been easily fixed by lightly sticking a finger on the fan to stop it for a second and it would go back to normal.
However, about a month ago this little fix stopped working. The grinding noise was unbearable. After searching the Internet for a few minutes, I found out that I wasn't the only one suffering from this problem, and some even offered tips on how to replace the fan.
I followed the steps very carefully and made sure the card was not harmed. After installing the new fan, which was very easy, I stuck it back into the Power Mac and boot it up. However the monitor didn't find a signal.
I was glad that I installed Remote Desktop on the Power Mac so I was able to connect to it and see what's going on. I opened Apple System Profiler and noticed that the computer isn't properly recognizing the graphics card anymore! Instead of the very detailed information I'm used to seeing, this is what I saw below:
pci10de,a:
Type: VGA-Compatible Controller
Bus: AGP
Slot: SLOT-1
Vendor: nVIDIA (0x10de)
Device ID: 0x252
Revision ID: 0x00a3
I have no clue what this means as it seems like the computer still recognizes A video card. Also this also gave me the impression that the Power Mac is missing the drivers, but that's impossible as I haven't touched the software on the hard drive and nVidia drivers are part of OS X.
If the card is broken then fine, I'll take my losses and buy a new one as I would hate to just throw the computer away since it still more than fulfill my needs. But I just hope the AGP slot isn't broken.
Any ideas? Thanks in advance.

Just for clarification:
You have two systems based on the same MS-7008 mainboard, correct? Both use the same BIOS Version?
In one system, the card is functioning, running in AGP 3.0 Mode x8 and in the other, same mainboard model, what are the symptoms of "video card not recognized" besides the AGP 2.0 Mode x4 limitation?
I mean, if you can see the BIOS Setup, the card is putting something out on the screen, right?

How to download a pdf file in external storage(sd-card) not use a isolated storage wp8

i have a url for download pdf file return by webservices
and i have attach this link in hypertext button this is start a download but in browser . and when i am google for this purpose the give me "
Background file transfer
" Process and then code is also using a isolated storage but i want a external storage process Please Help me
how to download a pdf file in external storage(sd-card) not use a isolated storage wp8

Hello,
This forum is for discussions and questions regarding profiles and Microsoft's recognition system on the MSDN and TechNet sites. It is not for products/technologies.
As it's off-topic here, I am moving the question to the
Where is the forum for... forum.
Karl
When you see answers and helpful posts, please click Vote As Helpful, Propose As Answer, and/or Mark As Answer.
My Blog: Unlock PowerShell
My Book: Windows PowerShell 2.0 Bible
My E-mail: -join ('6F6C646B61726C40686F746D61696C2E636F6D'-split'(?<=\G.{2})'|%{if($_){[char][int]"0x$_"}})

I have installed the agent 10 or 15 times and one installation hasfailed, no error appeared during the installation but I am havinginconsistent issues with my ethernet card not working here and there. Werebooted and can log into Novell client but th

I have installed the agent 10 or 15 times and one installation has failed, no error appeared during the installation but I am having inconsistent issues with my ethernet card not working here and there. We rebooted and can log into Novell client but the login prompt did not appear for ESM client or the icon was not in the systray. Everything seems to work, besides at times (a couple times today) it terminates his ethernet card/connection. I would re-image his computer but he has several applications and it would take several hours, so I am hoping someone has an idea to fix this issue. So I was trying to figure out why he did not get the prompt to login and why it's not in the systray and it appears to not have completed the install? I checked the add/remove programs, its not listed within their, I also checked the registry and found nothing for endpoint within their, but the files are within c:\program files\novell\zenworks endpoint security.
I have also tried uninstalling it but that fails due to it "not being installed", and it will not reinstall over itself either.
I did notice that stuninstdrv.exe is running in task manager. Any help would be great...
Windows xp sp3
ESM 3.5.154
Thanks,
Andy

If you are searching the registry, check for the "Senforce" string. It should be at HKLM\Software\Senforce
Try running the install program for the ZSC with the following command line:
setup.exe /V"STUNINSTALL=1"
If you've specified an uninstall password, try this one instead:
setup.exe /V"STUNINSTALL=1 STUIP=password"" (please note the double quote at the end)
Let me know if that helped you.
Daniel
>>>
From: Andy_DeWees<[email protected] du>
To:novell.support.zenworks.endpoint-security-management
Date: 2/5/2009 12:52 PM
Subject: I have installed the agent 10 or 15 times and one installation hasfailed, no error appeared during the installation but I am havinginconsistent issues with my ethernet card not working here and there. Werebooted and can log into Novell client but the login prompt did not appearfor ESM client or the icon was not in the systray. Everything seems towork, besides at times (a couple times today) it terminates his ethernetcard/connection. I would re-image his computer but he has severalapplications and
I have installed the agent 10 or 15 times and one installation has failed, no error appeared during the installation but I am having inconsistent issues with my ethernet card not working here and there. We rebooted and can log into Novell client but the login prompt did not appear for ESM client or the icon was not in the systray. Everything seems to work, besides at times (a couple times today) it terminates his ethernet card/connection. I would re-image his computer but he has several applications and it would take several hours, so I am hoping someone has an idea to fix this issue. So I was trying to figure out why he did not get the prompt to login and why it's not in the systray and it appears to not have completed the install? I checked the add/remove programs, its not listed within their, I also checked the registry and found nothing for endpoint within their, but the files are within c:\program files\novell\zenworks endpoint security.
I have also tried uninstalling it but that fails due to it "not being installed", and it will not reinstall over itself either.
I did notice that stuninstdrv.exe is running in task manager. Any help would be great...
Windows xp sp3
ESM 3.5.154
Thanks,
Andy

SB04100 Sound Blaster Card not working after computer rebuild

=SB0400 Sound Blaster Card not working after computer rebuildZ I did a full disk format and reinstall for a friend on a Dimension 3000, running XP SP3. There is no sound at all. Speakers are good, tested on another system. Model number on the back of the sound card is SB0400, so I assume this is an older 24 bit PCI SoundBlaster card. Although I reinstalled all drivers from Dell, I found no drivers for this. The Creative site has no listing for this model.
Computer does not seem to recognize the card. Have not opened the box yet but I assume if I were to remove and then reinstall the card it would be recognized (?) I then have to find an SB0400 driver.
Does anyone know where I can find an SB0400 driver ? Does the strategy of pulling and reinstalling the card make sense ? (I have really avoided tampering with any of the hardware on this box -- since it is not mine.)

Re: SB0400 Sound Blaster Card not working after computer rebuild? Thanks much for your response. Problem solved for now. I removed the board and then reinserted it, after which I was able to download the drivers directly. Some of my difficulty with this whole process has been ) I didn't know there was no working speaker in the computer and 2) I apparently misunderstood the BIOS settings for this. I re-set it up as an add-on board during the troubleshooting process. After loading the driver, I went back to the original setting (don't recall what it was but it was for integrated sound). The setting for integrated sound works fine, with external speakers and the new 24 bit driver. Still some noise (popping and static) but this board shares the bus with 2 other cards one of which is a wireless network card. May be a PCI latency issue but I'm reluctant to change that because the network card is a bit shaky anyway.
Everything works for now -- I'll be glad to get this particular computer out of my house !

SD Card not mounting with Yosemite, Disk Utility Yes, Finder No

Hi Everyone!
mid-2012 15" rMBP
2.7 GHz i7
16 GB 1600 MHz DDR3
Yosemite 10.10
Installed Yosemite about 2 weeks ago. So far things have been fine.
Just this morning tried reading a Nikon formatted Sony Class 10 (40MB/s) 16 GB SD card through the internal SD card reader - and nothing happened. After some poking around I noticed that the SD card is recognized by both the Disk Utility and the System Software, but not by Finder. The SD card will not mount.
It is not the SD card because it will mount on my buddies MBP running Mavericks (I had to upload the photos through Dropbox off his MBP).
I have already tried resetting both the PRAM and the SMC - it did not change anything. The system would still not mount the SD Card.
Here is the interesting thing. I have taken an old Class 4 8GB SD card which also wasn't being recognized and using Disk Utility, reformatted from MS DOS FAT to EXFat. Now Finder will in fact mount the drive. However, my Nikon or other devices will not accept an ExFAT formatted SD Card.
Check this out:
Anyone have any ideas?
THANKS IN ADVANCE!!!

Re: SD Card not working on Yosemite
Reset NVRAM/PRAM
Reset SMC

Error :Receiver File Channel not Initialized

Hi all,
I am using a file adapter at the receiver side with file content conversion option. When i post a message it shows an error in the message monitoring as "Reciever File Channel not initialized : Unable to proceed : null"
Please Help.....

Hi,
Check if the adapter is active or
check on this thread:
File Adapter Not Initialized Error
the error might be due to FCC. Jsut remove that and see ift he adapter works.
Regards
vijaya

Error in communication channel " not initialized"

Hi All,
I'm working in FIle to mail scenario. In this scenario whenever i upload a text file to the R/3 application server. that file should be sent (as a attachment with a mail) to any email id. I did all the required configuration in IR. but i'm verymuch confused in ID configuration. I have created both sender and receiver communication channel in the same business system which refers a sender (R/3) System.sender communication channel is working fine. but when i activate the receiver communication channel it shows an error "not initialized".
So kindly let me know,
1. Should i use business system for my receiver end?,If so how do i create it?
2. is receiver agreement, receiver determination, interface mapping necessary? If so, how do i configure it? because i'm not using any recever service since i'm sending mail to my mail box.
note:
It would be very helpful if u refer any link to find out the recever determination and interface determination configuration for this type of scenario.
Thanks & Regards,
hari.

Provide us the XML formed after mapping.
make sure that the msg type name is Mail and the name space name is http://sap.com/xi/XI/Mail/30.
regards
krishna

No Aapter registered for the channel and not initialized

Hi Guys,
I am working on Mail 2 File scenario. when the scenario is executed i am getting the below error in sender MAIL adapter communication channel.
No adapter registerd for the channel & not initialized
Thnx,
Siva

Hi,
Depending on your XI/PI version, apply one of the notes below to correct import the ESR content:
PI 7.1X:
#1152640 - SAP NetWeaver 7.1 including EHP 1: Importing ESR content
XI 7.0:
#836200 - SAP NetWeaver 7.0: Importing Process Integration Content
XI 3.0:
#705541 - XI 3.0 (SP1 and higher): Importing XI Content
Also, check if the service for the adapters are running. Restart the J2EE Engine.
If not solved, you may try redeploying the adapter's driver.
Regards,
Caio Cagnani

BPM error:Container element in step transformation is not initialized

Hello Experts,
I am new to the concept of BPM.
I'm trying to create an integration process in which I'm taking an Idoc and processing it in many ways. The process contains many transformation steps. There two such transformation steps which have been placed in block step in a fork. And i get this error: Container element XXX in step transformation is not initialized
What could be the problem?
Regards,
Akhil

Hi
if u are getting the messaga with red sigh then it means it will craete the error while running the scenario.
but if it is in blue then i think it will not create any error.
the meaning of that statement is that the container u have defind is not used anywhere. it is just giving u a warning message.
Thanks
Rinku

Vic card not initializing

Similar Messages

Maybe you are looking for