VIC3-2FXS/DID VS VIC3-2FXS-E/DID

hi all,
we'll upgrade our router from 2811 to 2911.
the current 2811 uses VIC2-2FXS but saw on cisco's website that we need a VIC3 instead.
i saw there's two versions of this card, the other has an 'E'.
what's the difference between the two? can i just get a VIC3-2FXS/DID?

Hi John,
The difference is explained in the following link
http://www.cisco.com/c/en/us/products/collateral/interfaces-modules/ip-communications-voice-fax-network-modules/product_data_sheet0900aecd801c595e.html
VIC3-2FXS-E/DID is designated as an "Off-Premise Extension Lite" product offering. This means that while the module addresses a subset of the off-premise extension applications, it should be noted that the module is not in full compliance for off-premise usage.
HTH
Manish

Similar Messages

  • How to install 2-port vic3 2fxs/DID and 2-port vic2 fxo on cisco 2801 router

    Hello
    I'm looking for information on how to install 2 newly purchased cards  and keep running into dead links. The cards I bought are for a  CISCO-2801-CCME/K9 with PVDM2-8, FL-CCME-25, SP Services 128F/256D cisco  router:
    vic3 2fxs/DID and a vic2 2fxo.
    I keep finding documents on how to  install these cards but all links are dead and leading to nowhere.
    http://www.cisco.com/en/US/docs/routers/access/interfaces/ic/hardware/installation/guide/2port_FXS_DID_VIC.html#wp1065062
    The  2 documents i'm looking for are: how to install a 2-port vic2 fxo cards on cisco  2801 router and how to install 2-port vic3 2fxs/DID cards on the same 2801 cisco  router.
    NOTE: I've never installed these cards and am not sure if:
    Does my  ios support both of these cards?
    and which slots do I install those in the  router.
    I have 4 slots like this:
    slot 0: This slot only accepts VIC's   ***This could be used for the vic3 2fxs/DID card correct?
    slot 1: Nothing  written here  ****What can i install in this slot?
    slot 2: This slot only  accepts VIC's and WIC's  ***If I buy a WIC and install here which other slot can  i install my VIC2-2FXO card in ?
    slot 3: Nothing written here  ***What can i  install in this slot?
    Any chance someone can help me out with this.
    Thanks  very much

    Ok
    I was able to figure out what goes where and found out that the IOS i had c-2801-spservicesk9-mz.124-15.T10.bin with cme-full-4.1.0.2 tar didn't support the vic3 2fxs/DID card. I then found the one that works which is the c2801-spservicesk9-mz.124-22.YB5.bin.I am now able to see my new hardware interfaces. The question I have now is since the previous version ran with cme-full-4.1.0.2 tar i'm not sure if this needs to be changed since in the compatibility matrix i found this IOS c2801-spservicesk9-mz.124-22.YB5.bin to be compatible with cme-full-7.1.0.0 tar
    Do i need to remove cme-full-4.1.0.2 tar and install the cme-full-7.1.0.0 tar?
    If yes, i know how to install the cme-full-7.1.0.0 tar but how do i remove the other cme-full-4.1.0.2 tar file in order to be able to install the other version?
    Thanks

  • Vic3-2FXS/DID fax problem

    I have a network in Beijing China below,
    (1) E1 Pri interface to PSTN
    (2) Vic3-2FXS/DID to fax machine
    all these modules installed on Cisco 2900, when I call my fax machine from PSTN, the fax machine answered, but fax can't start.
    I want to know is there any special consideration about the fax configuration to be worked.
    Thanks for your advice.
    Robert
    2011/2/18

    Hey Robert.
    Since you have PRI and the fxs port on the same card, in theory there is not a whole lot you need to do with regards to the fax or port configuration on the router if this is H323 or SIP.  On our initial voip gateways even on port to port calls we would invoke fax relay, but on the ISR line with the internal tdm backplane, the dsp should be dropped from the call with minimal impairment of the connection through the gateway.
    Now, this is true as long as you don't have "no local-bypass' configured under the voice-card.  Default is that this is not configured but it you do, you should change it to local-bypass.  "show voice dsp active" will show if the dsp is still in the loop on the call as well.
    Definitely check the E1 controller ("show controller e1") for slips and errors.  This will kill a fax if present.
    Looking back at your previous post though, I would not expect you to be seeing G722 on the output of the show voice call summary when the call connects between the two ports.
    Are you using MGCP?
    When the call is active between the two ports, what is the output of "show call active voice brief" and "show call active fax brief"?
    There are a few good resources for troubleshooting fax issues.  An excellent source if the CiscoPress publication "Fax, Modem and Text for IP Telephony".  If you would like some of the scaled down versions, I have posted a couple of links that would be useful.
    Bryan
    https://supportforums.cisco.com/community/netpro/collaboration-voice-video/ip-telephony/blog/2010/10/26/fax-configuration-and-troubleshooting-project
    http://www.cisco.com/en/US/docs/ios/12_3/vvf_c/voice_troubleshooting/old/vts_fax.html

  • VIC3-2FXS/DID

    Hi everybody,
    We have a CCM version 4.x and we need to connect two fax extensions on a VIC3-2FXS/DID card.
    The problem is that the faxs are 6 floors up the CCM. Between floors are connected by Optical fiber thought Cisco Switchs. We can configure these faxs on that card?
    Thanks!!

    VIC3-2FXS/DID
    If you have copper pairs to connect, yes.<-- means that if we connect the faxs to a switch and the VIC3-2FXS/DID  to the other switch with Ethernet cable it will work?
    VIC3-2FXS/DID

  • ATA vs VG202 vs VIC3-2FXS-E/DID & Wireless

    What is best solution moving forward?
    Fax server probably two years out.
    Background:
    I have 34 locations
    30 locations have 2 analog devices
    4 Operations have 26, 14, 15, 10 analog devices
    Currently we use ATA 188 and 186 and one VIC2-2FXS
    We Have intermittent problems receiving faxes from Fax servers or other customers in general.

    The VG20x are nice because you can use them as a full blown router (VPN, IGP, etc).
    I think you'll have more cost per port using a VIC3 rather than VG204. Their capabilities will be equal, as opposed to when the ATAs were in use.
    The ATAs are on their way out, and I think you'll find the VG20x to be an easier product to use and it will work better with faxes/modems. The ATAs don't have great fax/modem support where the VG20x will have T38 support and modem support.
    For the locations with 15+ devices it may be worth looking into the VG224 as well, depending on usage.
    -nick

  • Why the ringing voltage closely 0v for VIC3-2FXS/DID port?

    Initially, I have tested every port of FXS module on ISR with an analog phone. There
    was ringing tone and I was able to communicate to other as normal. The second
    test involved measuring the ringing voltage on the same ports by using a pair cable and multimeter. The
    'idle voltage' measured was around 44V and when there was an incoming call, the measured 'ringing
    voltage' was close to 0V.
    So why the ringing voltage is drop to 0V?
    Please advice.

    You cannot measure ringing voltage with a common multimeter. Read why:
    http://www.sandman.com/ringvoltbul.html

  • VIC3-4FXO/DID module not detect in 2801 Router.

    Hi Team,
    I have Cisco 2801 router with 2 DSP 16 Channel, 128 MB DRAM and 128 MB flash. I am using IOS c2801-spservicesk9-mz.124-3i but the VIC3-4FXO/DID module is not detected. I tried to upgrade the IOS to 15.0 and 15.1 but the router is not boot up due to insufficient memory.  In that IOS the FXO card is detected.  I checked the data sheet of both router and FXO card it support 12.4T IOS but when I upload the IOS and try to boot same problem I have faced (router not boot due to insufficient memory).  Kindly help me find out the appropriate IOS to resolve the issue.
    Thanks in advance.
    Regards, 
    Manas Ranjan

    VIC3-4FXO card is not supported in 2801 according to table4 
    Table 4. Software and Memory Requirements for Voice/Fax Network Modules and Voice Interface Cards
    Product
    Cisco 2800 Series
    Cisco 3800 Series
    Cisco 2900 and 3900 Series
    NM-HD-1V
    NM-HD-2V
    NM-HD-2VE
    • Cisco IOS Software
    • Release 12.3(8)T4
    • "IP Voice" images
    • Cisco IOS Software
    • Release 12.3(11)T
    • "IP Voice" images
    • Cisco IOS Software Release 15.0(1)M
    • "UC Technology" images
    VIC2-2FXO
    VIC2-4FXO
    VIC2-2BRI-NT/TE
    • Cisco IOS Software
    • Release 12.3(8)T4
    • "IP Voice" images
    • Cisco IOS Software
    • Release 12.3(11)T
    • "IP Voice" images
    • Cisco IOS Software Release 15.0(1)M
    • "UC Technology" images
    VWIC2-xMFT-xx
    • Cisco IOS Software
    • Release 12.3(14)T
    • "IP Voice" images
    • Cisco IOS Software
    • Release 12.3(14)T
    • "IP Voice" images
    • Cisco IOS Software Release 15.0(1)M
    • "UC Technology" images
    VIC3-2E/M
    • Cisco IOS Software
    • Release 12.4(15)XW or 12.4(20)T
    • "IP Voice" images
    • Cisco IOS Software
    • Release 12.4(15)XW or 12.4(20)T
    • "IP Voice" images
    • Cisco IOS Software Release 15.0(1)M
    • "UC Technology" images
    VIC3-2FXS/DID
    VIC3-2FXS-E/DID
    VIC3-4FXS/DID
    • Cisco IOS Software
    • Release 12.4(15)XZ or 12.4(20)T
    • "IP Voice" images
    • Cisco IOS Software
    • Release 12.4(15)XZ or 12.4(20)T
    • "IP Voice" images
    • Cisco IOS Software Release 15.0(1)M
    • "UC Technology" images

  • DSP Resource for VIC3-4FXS/DID on NM-HDV2

    Hi,
    If only PVDM3 is installed on the C3945 motherboard (Slot 0), and I have VIC3-4FXS/DID inserted in the NM-HDV2 and but without PVDM2 installed in the NM-HDV2, can I still enable the FXS port?
    Do I need to have this command to enable dsp sharing with the NM-HDV2?
    voice-card 1
    dsp tdm pooling
    Also, should the FXS ports appear in the "show voice port summary"?
    Thank you.

    Hi,
    just refer this
    http://www.cisco.com/c/en/us/products/interfaces-modules/2800-3800-high-density-packet-voice-digital-signal-processor/index.html
    Are the PVDM3 modules supported in a NM-HDV2?
    A. No. You cannot install PVDM3 modules directly on the PVDM slots of an NM-HDV2, only the PVDM2s are
    supported by the NM-HDV2. However, an NM-HDV2 that has no PVDMs installed at all can share PVDM3 DSP
    resources from the router motherboard PVDM slots across the chassis backplane.
    Q. Do the PVDM2 modules work with the Cisco 2900 and 3900 Series platforms?
    A. Yes. You can install PVDM2 modules on the motherboard PVDM slots using special adaptor cards (PVDM2-
    ADPTR). You can also insert an NM-HDV2 module with PVDM2 modules into the service-module slot of the
    Cisco 2900 and 3900 Series platforms using the network-to-server module adaptor card (SM-NM-ADPTR).
    regds,
    aman

  • 2801 can not detect VIC3-2FXS card.

    Hi,
    I have the 2801 router with a VIC3-2FXS card that is not detecting, I see it with sh diag command like Unkown WAN card.
    The IOS that I´m using is:
    Cisco IOS Software, 2801 Software (C2801-SPSERVICESK9-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3)
    System image file is "flash:c2801-spservicesk9-mz.124-15.T7.bin"
    I checked the details and It can support it.
    Do you have any idea what I can do ?.
    Thank you, best regards.

    Thank you by your support.
    Do you know If I can use next IOS:
    c2801-ipvoicek9-mz.124-24.T2.bin 
    Release Date: 22/Oct/2009
    Size: 39192.34 KB  (40132948 bytes)
    Minimum Memory: DRAM:192 MB  Flash:64 MB
    Thank you, best regards.

  • Analog Lines to E1 DID/DOD configuration need for CCME

    Dear,
    I have one of our remote site have the following configuration:
    * 2 X CCME running on C3845.
    * 1 X CUE installed on one of the C3845
    * Around 70 IPT (7910, 7941 & 7941) registres in the CCME.
    * 8 * analog lines connected to FXO ports that provide land lind connectivity for the site.
    * 4 * FXS ports to provide FAX.
    and becasue of unstability issue with the out/ingoing call we requested 4 X voice E1 DID/DOD. and want to know what is the required configuration to consider in migrating my remote site.
    regards

    Hello, thanks for your responses  helped me very much.
    I have the commands and errors completes:
    When I enter the command:
    ds0-group 0 timeslots 1-15,17-25 type r2-digital r2-compelled ani into the controller e1, I receive this error:
    % Not enough DSP resources available to configure ds0-group 0 on controller E1 0/0/0
    % The remaining dsp resources are enough for 20 time slots.
    % For current codec complexity, 1 extra dsp(s) are required to create this voiceport.
    This the inventory in the router:
    GW-VOSS(config-controller)#do sh inv
    NAME: "2821 chassis", DESCR: "2821 chassis" PID: CISCO2821         , VID: V05 , SN: FTX1336AHFS
    NAME: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1"  PID: VWIC2-1MFT-T1/E1  , VID: V01 , SN: FOC133129NF
    NAME: "2nd generation two port FXO voice interface daughtercard on Slot 0 SubSlot 1", DESCR: "2nd generation two port FXO voice interface daughtercard"PID: VIC2-2FXO         , VID: V02 , SN: FOC13332NDZ
    NAME: "3rd generation two port FXS DID voice interface daughtercard on Slot 0 SubSlot 2", DESCR: "3rd generation two port FXS DID voice interface daughtercard" PID: VIC3-2FXS/DID     , VID: V01 , SN: FOC132526S0
    NAME: "PVDMII DSP SIMM with four DSPs on Slot 0 SubSlot 4", DESCR: "PVDMII DSP S IMM with four DSPs" PID: PVDM2-64          , VID: V01 , SN: FOC13341ZE1.
    I  have the transcoding:
    dspfarm profile 1 transcode 
    codec g711ulaw
    codec g711alaw
    codec g729ar8
    codec g729abr8
    codec g729r8
    codec g729br8
    maximum sessions 15
    associate application SCCP
    I have CUCM 7.0, Contac Center 6.0, SIP trunk, 1 E1.
    I need another PVDM card? The router can be have two PVDM card? Which PVDM card you recommend ?
    Regards

  • I am having macbook air recently my iphotos did not open and was showing report apple and reopen but i came to know that by pressing alt and iphotos i open an new photo library and stored the pics but now how can i get the pics which i had in the earlier

    i am having macbook air recently my iphotos did not open and was showing report apple and reopen but i came to know that by pressing alt and iphotos i open an new photo library and stored the pics but now how can i get the pics which i had in the earlier photo please help me to recover my photos

    Well I'll guess you're using iPhoto 11:
    Option 1
    Back Up and try rebuild the library: hold down the command and option (or alt) keys while launching iPhoto. Use the resulting dialogue to rebuild. Choose to Repair Database. If that doesn't help, then try again, this time using Rebuild Database.
    If that fails:
    Option 2
    Download iPhoto Library Manager and use its rebuild function. (In early versions of Library Manager it's the File -> Rebuild command. In later versions it's under the Library menu.)
    This will create an entirely new library. It will then copy (or try to) your photos and all the associated metadata and versions to this new Library, and arrange it as close as it can to what you had in the damaged Library. It does this based on information it finds in the iPhoto sharing mechanism - but that means that things not shared won't be there, so no slideshows, books or calendars, for instance - but it should get all your events, albums and keywords, faces and places back.
    Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one.  
    Regards
    TD

  • I create a birthday calendar in iCal and then click on it in iphoto at the begining of the calendar project each year.  Some how the birthday did not populate the photo calendar.  Is there a way to add the birthday iCal calendar into the calendar project?

    I created a birthday calendar to use in iphoto for calendar.  When a new calendar project is started each year, I click on it in.  Some how the birthday did not populate the photo calendar this year.  The photo calendar is almost complete.  Is there a way to add the birthday iCal calendar into the calendar project? I would prefer not to start over.

    Hi,
    If you first select the calendar on the left, so that its background is highlighted blue/grey, when you make a new events they should be added to that calendar.
    Best wishes
    John M

  • HP LaserJet Enterprise 500 551dn - where did the drivers go?

    I go to the download page to download the drivers for this 551dn.  I download all windows 7, 8, 8.1, 2008, 2012, so that i can put them on my print server.  I downloaded them from here..
    <http>//h20564.www2.hp.com/hpsc/swd/public/readIndex?sp4ts.oid=5081348&lang=en&lang=en&cc=lamerica_n...
    when i get the file, lets say for windows 7/64bit, i choose...
    HP LaserJet Enterprise 500 color M551 Printer Series PCL6 Print Driver (no Installer) 61.130.04.12834
    24 Sep 2014 21.3
    I get the file downloaded (LJEnt-color-M551-Drv-no-installer_12297.exe), i run it, get the security warning and Run.  the file extracts - then POOF, the installer is gone.
    where did the files go?  They aren't on the root of the C: drive, a folder/files were not created on my desktop, no files or folder created in my downloads folder.
    I was never asked for a file save location.... ???  really?   is this this basic stuff? 
    Where are the files?  this $$$ printer is a brick until i get drivers! 
    Thanks!
    Jason
    UPDATE- I FOUND THE FILES!!
    First of all, HP... i'm not impressed.
    All the files for all the drivers are in a series of temp folders...
    C:\Users\-myusername-\AppData\Local\Temp\3\7zS4A73
    really?
    hope this helps someone. 

    There is no change to this problem after 6 months since the last post. Put simply, and as stated in the previous posts, there is no way to scan a document and receive the image on your PC. If you are working with graphics for any length of time or want to create an image for inclusion as an image in a document or web page using this piece of equipment will not allow you to do so.
    Great shame as every other function works well - it cannot be beyond the wit of HP to include a Windows application that enables you to scan an image, receive it in the software you are using at the time (e.g. Outlook, Word, Photoshop...) and use it in your work.
    HP Printers several years older than this £1000+ Enterprise printer were able to do this simple job and have done so for a great many years. Just being able to use Microsoft's Fax and Scan would be start.

  • How to find out list user who did the printing

    Dear All,
    We are using network print server using HP LaserJet 5550 and jetdirect, since our number of users is more than 500 staff in one place, sometimes they do the unresponsible printing such as print full color photos for personal use, print a novel and anything that not related to the business purpose.
    Today, our director found out that someone print out a whole story book and spend a lot of paper... he challenge me to find out who is the user who did this? I can log on to the printer web console, but I can't find user log printing...
    Any help will be much appreciated.
    Thanks & Regards,
    Franky

    This seems to be a commercial product. For the best chance at finding a solution I would suggest posting in the forum for HP Business Support!
    You can find the Commercial Jetdirect board here:
    http://h30499.www3.hp.com/t5/Print-Servers-Network​-Storage/bd-p/bsc-254
    Best of Luck!
    You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

  • Did You Know -- Ten Innovations

    Good afternoon Did You Know fans! 
    Did you know HP customers can now print anything from anywhere with HP’s web-connected printing?  HP announced this exciting news along with other industry-first innovations unveiled by HP just Monday of this week.  Our teams are hard at work bringing the latest cutting edge technology straight to you.  Here’s some highlights of the news we announced this week that include driverless printing and the world’s smallest and one of the world’s most energy efficient color laser printers
    Some of our industry-first innovations include:
    The planet’s first PVC-free printer, the HP ENVY100 e-All-in-One, which lends cutting-edge design with wireless, Web-connected printing and access to HP‘s  “advanced apps”
    The industry’s first Web-ready large-format printer, the HP Designjet T2300 eMFP, featuring scan, print and copy functionality, with:
    Driverless printing from a laptop or USB drive for the first time, eliminating print driver and network constraints
    World’s first color touch-screen interface on a large-format printer
    World’s first large-format multi-function device at price point below $8,500, opening the door to in-house large-format printing for more customers
    The world’s first wide-format all-in-one device with web connectivity on the HP Officejet 7500A Wide Format e-All-in-One
    The world’s smallest color laser printer and one of the world‘s most energy efficient color laser printers, the HP LaserJet Pro 1025nw Color Printer
    World’s first consumer All-in-One printer with full Web browser and detachable touchscreen display on the HP Photosmart eStation All-in-One
    For the first time, enabling two-way print through the cloud for businesses, using HP Print Apps, creating an unparalleled web experience for business customers to access, manage, and share content from templates and stored documents
    World’s fastest production photo large-format printer within its class – the HP Designjet Z6200 Printer, increasing productivity for the graphics professional
    Check out the official news here in HP’s newsroom!
    HP Product Expert for the Officejet Pro X Series.
    Was your question answered? Mark it as an Accepted Solution!
    See a great post? Give it a Kudos!

    I do hope others find the videos useful. 
    ↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

Maybe you are looking for