VIC3-4FXO/DID module not detect in 2801 Router.

Hi Team,
I have Cisco 2801 router with 2 DSP 16 Channel, 128 MB DRAM and 128 MB flash. I am using IOS c2801-spservicesk9-mz.124-3i but the VIC3-4FXO/DID module is not detected. I tried to upgrade the IOS to 15.0 and 15.1 but the router is not boot up due to insufficient memory. In that IOS the FXO card is detected. I checked the data sheet of both router and FXO card it support 12.4T IOS but when I upload the IOS and try to boot same problem I have faced (router not boot due to insufficient memory). Kindly help me find out the appropriate IOS to resolve the issue.
Thanks in advance.
Regards,
Manas Ranjan

VIC3-4FXO card is not supported in 2801 according to table4
Table 4. Software and Memory Requirements for Voice/Fax Network Modules and Voice Interface Cards
Product
Cisco 2800 Series
Cisco 3800 Series
Cisco 2900 and 3900 Series
NM-HD-1V
NM-HD-2V
NM-HD-2VE
• Cisco IOS Software
• Release 12.3(8)T4
• "IP Voice" images
• Cisco IOS Software
• Release 12.3(11)T
• "IP Voice" images
• Cisco IOS Software Release 15.0(1)M
• "UC Technology" images
VIC2-2FXO
VIC2-4FXO
VIC2-2BRI-NT/TE
• Cisco IOS Software
• Release 12.3(8)T4
• "IP Voice" images
• Cisco IOS Software
• Release 12.3(11)T
• "IP Voice" images
• Cisco IOS Software Release 15.0(1)M
• "UC Technology" images
VWIC2-xMFT-xx
• Cisco IOS Software
• Release 12.3(14)T
• "IP Voice" images
• Cisco IOS Software
• Release 12.3(14)T
• "IP Voice" images
• Cisco IOS Software Release 15.0(1)M
• "UC Technology" images
VIC3-2E/M
• Cisco IOS Software
• Release 12.4(15)XW or 12.4(20)T
• "IP Voice" images
• Cisco IOS Software
• Release 12.4(15)XW or 12.4(20)T
• "IP Voice" images
• Cisco IOS Software Release 15.0(1)M
• "UC Technology" images
VIC3-2FXS/DID
VIC3-2FXS-E/DID
VIC3-4FXS/DID
• Cisco IOS Software
• Release 12.4(15)XZ or 12.4(20)T
• "IP Voice" images
• Cisco IOS Software
• Release 12.4(15)XZ or 12.4(20)T
• "IP Voice" images
• Cisco IOS Software Release 15.0(1)M
• "UC Technology" images

Similar Messages

Yoga 10 not detecting ASUS wireless router

Hello,
I had recently purchased a yoga 10 tablet and it worked fine with the wireless router(ASUS RT-N13U).
Suddenly today it doesn't detect the wireless router anymore. It does show other wireless networks in our apartment but not ours.
Any help on this, will a factory reset help?
Thanks,
Jafar

Same problem here on yoga 8, wireless routers with same SSID and password in different locations will suddenly disconnect and appear out of range. Most times I have to forget the ssid, turn off Wlan, reboot the router then switch on wlan and set up the connection again. This is not a minor glitch and does not happen on any of my other android devices, I was hoping the 4.4.2-01-021 build would fix this but no such luck. I really like the yoga 8 design but along with other stupid basic problems I.e.google maps I'm begining to think I've brought a polished turd.

SPA modules not detected n LMS 3.1

Dear Friends,
Does anyone knows why my SPA modules are not getting detected in LMS 3.1. however SIP 200 / 400 modules are getting detected. is this some kind of limitations?
Regards,
Rajiv

hi,
Thanx for your prompt response.
We have done below configration at LMS end but we have not recd E-mail notification when module goes down and up.
LMS Configuration:
Trap Subscription Summary: Edit
Subscription Name: Module
Notification Group: MODULESALERT
Recipient(s): Hostname Port Comments
GUR-SC01.quest.com 162 Snmp-on-18-01-2010
GUR-SC02.quest.com 162 Snmp-on-18-01-2010

T1/E1 card not detected on the Router

I ordered a router for CME,with a T1/EI (1MFT-T1/E1) card. I have just realized that when I try to run the controller command, it says unrecognized command. When i show run,I dont see the controller interface. How ever, i tried another E1 card (1MFT-E1) on the same router, and it saw it.
Please advice, is there any command to activate the 1MFT-T1/E1 card?
How do confirm if its bad?

I recently ordered a 1MFT-T1/E1 card as well, and was in the same boat. When you do a show running, it will say something like "you must select the card type in slot 0" or whatever. This command is necessary to tell the card what mode to run in since it is both a T1 and E1.
Try this if you haven't already done so.
card type e1
If you've already done this, let us know and we can start helping out.
Lelio
Please rate helpful posts

How to install 2-port vic3 2fxs/DID and 2-port vic2 fxo on cisco 2801 router

Hello
I'm looking for information on how to install 2 newly purchased cards and keep running into dead links. The cards I bought are for a CISCO-2801-CCME/K9 with PVDM2-8, FL-CCME-25, SP Services 128F/256D cisco router:
vic3 2fxs/DID and a vic2 2fxo.
I keep finding documents on how to install these cards but all links are dead and leading to nowhere.
http://www.cisco.com/en/US/docs/routers/access/interfaces/ic/hardware/installation/guide/2port_FXS_DID_VIC.html#wp1065062
The 2 documents i'm looking for are: how to install a 2-port vic2 fxo cards on cisco 2801 router and how to install 2-port vic3 2fxs/DID cards on the same 2801 cisco router.
NOTE: I've never installed these cards and am not sure if:
Does my ios support both of these cards?
and which slots do I install those in the router.
I have 4 slots like this:
slot 0: This slot only accepts VIC's ***This could be used for the vic3 2fxs/DID card correct?
slot 1: Nothing written here ****What can i install in this slot?
slot 2: This slot only accepts VIC's and WIC's ***If I buy a WIC and install here which other slot can i install my VIC2-2FXO card in ?
slot 3: Nothing written here ***What can i install in this slot?
Any chance someone can help me out with this.
Thanks very much

Ok
I was able to figure out what goes where and found out that the IOS i had c-2801-spservicesk9-mz.124-15.T10.bin with cme-full-4.1.0.2 tar didn't support the vic3 2fxs/DID card. I then found the one that works which is the c2801-spservicesk9-mz.124-22.YB5.bin.I am now able to see my new hardware interfaces. The question I have now is since the previous version ran with cme-full-4.1.0.2 tar i'm not sure if this needs to be changed since in the compatibility matrix i found this IOS c2801-spservicesk9-mz.124-22.YB5.bin to be compatible with cme-full-7.1.0.0 tar
Do i need to remove cme-full-4.1.0.2 tar and install the cme-full-7.1.0.0 tar?
If yes, i know how to install the cme-full-7.1.0.0 tar but how do i remove the other cme-full-4.1.0.2 tar file in order to be able to install the other version?
Thanks

E63 doesn't detect my Netgear Router (wgr614 v6)

E63 does not detect my netgear router (wgr614 v6). My T-Mobile SDA and T-Mobile Shadow, can detect it easily and also connect successfully.
Here are the settings I have on router:
Security: WEP
Auth: Automatic
Encrypt: 64 bit
Channel: 6
Mode: g and b
All my laptops also connect through this router, but E63 cant even detect it.. is there something wrong..? My router broadcasts, I mean it is not hidden.. any help/suggestion..?

I had a similar experience a few years ago with an N80. In that instance the problem was resolved when I changed the router setting from b and g to g only.
You should also try updating the firmware on the router as there have been problems connecting to Netgear routers which were resolved with router firmware updates.

2801 can not detect VIC3-2FXS card.

Hi,
I have the 2801 router with a VIC3-2FXS card that is not detecting, I see it with sh diag command like Unkown WAN card.
The IOS that I´m using is:
Cisco IOS Software, 2801 Software (C2801-SPSERVICESK9-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3)
System image file is "flash:c2801-spservicesk9-mz.124-15.T7.bin"
I checked the details and It can support it.
Do you have any idea what I can do ?.
Thank you, best regards.

Thank you by your support.
Do you know If I can use next IOS:
c2801-ipvoicek9-mz.124-24.T2.bin
Release Date: 22/Oct/2009
Size: 39192.34 KB (40132948 bytes)
Minimum Memory: DRAM:192 MB Flash:64 MB
Thank you, best regards.

SBRIO slot 1 thermocouple module 9213 not detected on aluminum plate, while in other 2 slots working fine, any reason ?

Hi,
i have a peculiar problem,
I have a sbrio 9642XT mounted on an aluminum plate (also connected to earth ground) along with 9213 thermocouple on slot 1 and 9477 digital out module on slot 3.
previously this setup used to be on an acryllic plastic plate. and now when i shifted to the aluminum plate the thermocouple module is not being detected by labview project under chasis, while the 9477 is still being detected.at slot 3
i placed an analog inpt 9205 module on slot 1 just to see if there is a problem with slot 1, and yes the new module is also not detected on slot 1,
so placed it on slot 2 and now the thermocouple module is detected and works fine on slot 2.
the attached picture shows the Ungrounded T- type of Thermocouple Probes that I use , these are immersed in ice water and in some other inert liquids to read the temperature
so my question is, is the problem related to grounding issue caused by liquids and did it ruin the slot of the SBRIO some how or is the sbrio just got faulty after using for an year. or is it got something to do with the mounting on aluminum plate (earth ground)
also i never used slot 2 before.
is there a way to test in any other way to know if the slot 1 is ruined because of the above reasons or is it a software issue
i dont want to ruin the slot 2 of the sbrio by placing that thermocouple module. please help
many thanks,
Attachments:
thermocouple picture.pdf ‏105 KB

Hi Freemason,
Nothing you have described should be causing a slot to stop working; as long as the sbRIO is properly mounted and not touching the backplane, it shouldn't be a problem. If your slot 1 is not working, you could also send the board in to National Instruments for repair. Are you still under warranty?

Surface Pro 3 / "Windows did not detect a properly installed network adapter"

Hi all,
I've been running the Windows 10 Technical Preview (9926) on my Surface Pro 3 successfully
since January. Unfortunately, I lost all internet connectivity today.
The problem started when I noticed the type cover wasn't working (pressing keys on the type
cover wasn't registering any typing on my screen) and my USB mouse wasn't working either. I tried removing and reattaching the type keyboard but this didn't fix the issue. I had to use the accessibility on-screen keyboard to sign into Windows (thankfully touch
was still working). Once I signed in, I still didn't have typing or cursor ability, so I decided to restart the computer.
Then it got worse. I noticed the Surface Pro 3 was stuck on "restarting" and wouldn't
actually restart. Since it wasn't responding, I held down the power button for about 10 seconds until it turned off. When I turned it back on, the type cover and mouse started working again.
Unfortunately, this is when the WIFI problems began. I had WIFI for a few seconds, and then
I lost internet. I disconnected/reconnected but there was a yellow triangle telling me there was some sort of problem. So I restarted the Surface Pro 3.
When it came back on, there were suddenly NO connections available at all. Opening the "Network
& Internet" settings page gave me the message "Windows did not detect a properly installed network adapter". And here I am, without internet on my Surface Pro 3, borrowing my friend's computer so I can type this message (he is also running
Windows 10 build 9926 on his laptop and is able to connect to my WIFI with no problems, whereas my Surface Pro 3 cannot even detect any networks). I have not dropped or damaged the SP3 in any way, and there have been no storms or power outages or anything
of that sort. Any ideas what could have happened to the WIFI on my Surface Pro 3?
Thanks for your help...
Ethan

Hi Ethan,
Currently, there are a few compatibility issue between the current hardware and Windows 10 Technical Preview (9926 build), this is mostly related to driver compatibility issue.
I suggest you download the latest network adapter driver package to install, when it is finished, check if it appears under Device Manager.
Surface Pro 3, Surface Pro 2, and Surface Pro firmware and driver packs
https://www.microsoft.com/surface/en-us/support/networking-and-connectivity/install-wireless-drivers
You can check if you can install the latest firmware package for your device.
Here is an article to talk about such things:
Windows 10 January Technical Preview on Surface
https://www.microsoft.com/surface/en-us/support/install-update-activate/windows-technical-preview#Known
Regards,
Alex Zhao
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Hi, I got a virus that does not let me use Safari. I downloaded an av from the app.store but it did not detect anything. I am thinking in formatting the HD. How can I do it and will I lose?

Hi, I got a virus that does not let me use Safari. I downloaded an av from the app.store but it did not detect anything. I am thinking in formatting the HD. How can I do it and will I lose?

1. Force Quit .
    Press command + option + esc keys together at the same time. Wait.
    When Force Quit window appears, select the Safari if not already.
    Press Force Quit button at the bottom of the window.   Wait.
    Safari will quit.
    Relaunch Safari holding the shift key down.
2. Safari > Preferences > Extensions
    Turn those off and try Safari.
3. Safari > Preferences > Privacy > Cookies and other website data:
    Press “Remove all website data” button.
4. If adware is installed without your knowledge,
    download free AdwareMedic by clicking “Download ” from here
    http://www.adwaremedic.com
   Install , open, and run it by clicking “Scan for Adware” button   to remove adware.
   Once done scanning and removing the adware, quit the app by clicking AdMedic in the menubar
    and selecting “Quit AdwareMedic”.

Wndows did not detect any biometric devices on this computer..

I have an HP ProBook 4540s running Windows 7 Professional w/IE11. I had to do a clean install of Windows 7 Pro and since then I cannot get my fingerprint reader to work at all. In my Control panel, under Biometric Devices, I recieve the message "Windows did not detect any biometrics devices on this computer". However, under Computer , Properties, Device Manager, Biometric Devices, the is Validity Sensors (WBF) (PID=003d).
I have tried to update, uninstall, re-install HP Simplepass, drivers, etc from the HP website, but nothing is working. Also I cannot find exactly what fingerpriint reader hardware is installed on the computer even though it is physically there as part of the original configuration.
I appreciate any assistance in resolving this issue.
Mark

Hello Mark531,
Welcome at the HP forums,
Are you searching for the following driver?
http://ftp.hp.com/pub/softpaq/sp64001-64500/sp64338.exe
Winos.
The doors of wisdom are never shut. Benjamin Franklin
We must use time wisely and forever realize that the time is always ripe to do right. Nelson Mandela

Windows did not detect any networking hardware, Windows 7, New Hard Drive

Message "Windows did not detect any networking hardware"
Satellite P505 S8980 Windows 7 Home Premium.
I replaced the Toshiba 500 GB HD with 500 GB Seagate.
Device Manager icon for any device with yellow exclamation mark,
Click on "Update Driver". Lan eNet details as follows:
Antheo - R8132 PCI-E Fast Ethernet Controller (NDIS 6.20)
Browse to the folder where the setup program has the driver...
Message: "The best driver software is already installed."
(But the yellow exclamation mark still harasses me.)
--- Go to "Setup new connection" ---
"Choose a connection option"
Click on "Connect to the Internet"
Response: "Windows did not detect networking hardware"
As near as I can tell, that translates from error 0x8E5E0247
I have this same error on other yellow exclamation marks respective of what kind of device it is.
=> To test my sanity, I put the old hard drive (same size) back in and except for the impact of slowness due to error retries, everything works okay.
Note:
Same issue (hardware not detected) for Video adapter and Audio.
I bought new USB Wireless adapter to test, and the driver installed but not activated because "not digitally signed", and that same issue fits all the above hardware. I down loaded them from Toshiba, and they are confirmed installed, but not accepted with digitally signed. I have uninstalled and reinstalled with same results.
Solved!
Go to Solution.

I'm discovering I am not as well as I thought... running on the AF hard drive which was built with a copy drive from old format drive which was the product of system recovery disc set.
Review for context: Advanced Function HDD
Scenario that exposes harm caused by cloning data from 4K blocks drive to 512 bytes blocked drive (AF)
Toshiba supplied Windows-7 System Restore Discs: to factory state
Then I built the Windows-7 Repair Disc... used later.
Hard drive was replaced when it caused SMART warning at every system boot.
Acronis was only utility that quickly detected problem (3 sectors had permanent read errors.) Active@Disk Image and Power Quest Drive Image (Ghost) did not detect the issue.
I tried Seagate 500 GB and Western digital 500 GB HDD drives as copy target.
That new drive would not boot: "Required source not found"
Booted My newly created Windows-7 repair disc, and used to to fix startup.
See images.
That worked and then the ST9500423AS disc booted.
Now... next day I discovered Window Update is not working.
I get message:
Windows Update cannot currently check for updates, because the service is not running. You need to restart your computer.
I ran Microsoft Fixit for updates. It says it fixed two items.
I still have the problem.
The service shows "started"
Control Panel/ ACTION Center/ Maintenance/ Check for Updates
"No action needed"
"Windows Update does not require any action"
I checked Update History...
... It is empty, else window is vacant... blank.
Soooo..... for a sanity check, I swap out hard drive; go back to the old format (which is the one I copied).
It works! 7 updates to install, including SP1... but I did NOT install them.
Switch back to the AF drive... Update doesn't work. I am broke again.
Is this another strange problem caused by the Advance Format issue?
What to do?
By the way... I did install an Intel storage Matrix driver update, but I do not have RAID chip, so that driver is not for me... unless I missed out on something.
Carl

Windows did not detect any networking hardware iMac 27' 2013 model

Installed windows 7 using bootcamp now when I go to connect to a network it says windows did not detect any networking hardware

Did you install the windows drivers as well?

I just tranfer all my photo from my Mac though itune to my iPhone so I can setup Mac back to factory setting after doing I try to put my photo vac to my Mac I photo did not detect any of the photo that I had tranfer from itune it only detectPLAESE HELP!

I just tranfer all my photo from my Mac from itune to my Iphone so I can setup Mac back to factory setting after I don't with that, I try to put my photo back to my Mac and Iphoto did not detect any of the photo that I had tranfer from itune it only detect the one rhat i took with the Iphone PLAESE HELP!!!!!!

Hello Partii,
It sounds like you may use a POP account for your email. With a POP account, email applications like Mail and Outlook can remove emails from the server, so when another device tries to check the server for new emails, it doesn't see any.
You may need to adjust settings in Outlook so that the emails are not removed from the server when downloaded. I found an article with more information:
When using a POP email account with multiple devices, email messages may only appear on the first device that receives them. This occurs when an email client is configured to automatically remove email from the server once an email client has received it. You can configure your email client (or clients) either to keep a copy of the email on the server, remove it after a certain number of days have passed, or keep it until you move it from your Inbox.
I recommend reviewing the full article for steps on adjusting these settings; you can find the full article here:
Using a POP account with multiple devices
http://support.apple.com/kb/HT3228
Thank you for using Apple Support Communities.
Best,
Sheila M.

M2N78-LA Motherboard BIOS did not detect any Hard Drive

Hi,
I have M2N78-LA Motherboard and the BIOS did not detect ANY hard drive
I tried
1- Replaced the HD with another one. did not work
2- Changed the jumper of HD. did not work
3- Changed the SATA data cable and power cable. did not work.
4- Reset the BIOS by removing the battery and also by positioning the cmos jumber. did not work.
I still all time get no hard drive detected, and some time jam on Detecting storage devices ....
then after hours get no booting device.
Any Idea will be good

M2N78-LA Motherboard BIOS did not detect any Hard Drive, does anyone have an answer to this problem.

VIC3-4FXO/DID module not detect in 2801 Router.

Similar Messages

Maybe you are looking for