Video advantage 2.0.2.0 and 7985

Has anyone managed to get a video call working between these 2 systems? I am running CCM 4.1(3) sr3b. Any help please!
Thanks
Steve

Hi Steve,
Still running into problems? I've done this quite a few times with any glitches. Try upgrading the firmware on the 7985 to 4.1.2, I know that one works fine.
Regards,
Baris

Similar Messages

3511 MCU with video Advantage

1.DOe the 3511 MCU supports cisco Unified video advantage ( PC- USB camer based video product) for 3 or more party video conferencing ?
2. Does the video advantge endpoint can do video conference with IP phone 7985G ?

Answer is 'Yes' for both questions.
You can configure 3511 to use either Skinny or H323 protocol. If configure as Skinny, then it is just another CFB in CM; CM will allocate it as per MRG and MRGL configuration. If configured as H323, then you have to configure 3511 as H323 gateway in callmanager and have a RP to point to the gateway. Typically, the RP will be your conference ID number.
7985 is just another video phone like VTA with an IP Phone; and they do support same type of codecs. Hence you can use 7985 to do video call with VTA as well to do conference with an MCU.

Using Video advantage with IP Communicator on CME 4.0

I am having issues getting video advantage to work with IP communicator. I am using VA 2.0.2.0 and IPC 2.0.2.0 and CME 4.0. I added the commands
voice service voip
h323
call start slow
telephony-service
service phone videoCapability 1
call-park system redirect
create cnf-files
and added the video command under the ephone. If you have any suggestions I would appreciate it.
Thanks,
Andrew

Paal
I am not using Call Manager. I am using Call Manager Express. There is no version 4.1 the documentation says that it should work with 4.0. that is the latest version of CME. Do you have any insight on this.
Thanks,
Andrew

Best camera for Cisco Video Advantage

Hi,
I am looking for a camera which is having the best specifications for Video advantage. It looks like the Microsoft LifeCam NX-6000 is the one. (1600 x 1190 with 30 fps) Does anyone have experience with this camera or who has good experience with a camera which is not listed in the "tested" camera list:
Cisco VT Camera II
â¢ Cisco VT Camera
â¢ Logitech QuickCam Fusion
â¢ Logitech QuickCam for Notebooks Pro
â¢ Logitech QuickCam Pro 5000
â¢ Logitech QuickCam Ultra Vision
â¢ Microsoft LifeCam VX-6000
â¢ Microsoft LifeCam NX-6000 Webcam
â¢ Creative Webcam Live Pro USB 2.0 Webcam
Thanks in advance,
Jeroen

Hi Mark,
Thanks a lot for your reply. We tried several models which are not in the list. They all worked. The only problem is that the Video Advantage narrows down the format. I tried the Logitech Quickcam Sphere AF. In the Logitech application it's a great Webcam in with HD quality but these are the Specifications of Video advantage:
â¢ H.263 and H.264 video codecs: Bit rates from 50 kbps to 1.5 Mbps
â¢ Video formats (up to 30 frames per second): 352 x 288, 320 x 240, 176 x 144, and 160 x 120
â¢ Interoperable with most third-party H.323 video terminals from verified IP video telephony partners
So it's only working at 352 x 288. I hope the next version of Video advantage is able to increase the resolution.
I would also like to know if there is a way to enable the camera automatically when a phone call is established.
I don't have a MCU to do video conferencing but is there a way to conference a none-video phone into an video conversation?
Thanks!
Regards,
Jeroen

Hi..Iam an Architect...I would like to purchase a macbook pro 15.4 inch 512 gb, 16 gb.So i would like to know the possibilities and advantages of using 3d softwares and autocad.And also is 3dsmax available for mac os or should i install it with windows.

hi..Iam an Architect...I would like to purchase a macbook pro 15.4 inch 512 gb, 16 gb.So i would like to know the possibilities and advantages of using 3d softwares and autocad.And also is 3dsmax available for mac os or should i install it with windows.

System Requirements for AutoCAD 2013 for Mac:
Apple® Mac OS® X v10.8.0 or later (Mountain Lion), OS X v10.7.2 or later (Lion), or OS X v10.6.8 or later (Snow Leopard) with 64-bit Intel processor
Apple® Mac® Pro 4.1 or later; MacBook® Pro 5.1 or later (MacBook Pro 6.1 or later recommended); iMac® 8.1 or later (iMac 11.1 or later recommended); Mac® mini 3.1 or later (Mac mini 4.1 or later recommended); MacBook Air® 2.1 or later; MacBook® 5.1 or later (MacBook 7.1 or later recommended)
3 GB of RAM (4 GB recommended)
2.5 GB free disk space for download and installation (3 GB recommended)
All graphics cards on supported hardware
1,280 x 800 display with true color (1,600 x 1,200 recommended)
All Mac OS X supported language operating systems
Apple® Mouse, Apple Magic Mouse, Magic Trackpad, MacBook® Pro trackpad, or Microsoft-compliant mouse.
Mac OS X-compliant printer
Additional Requirements for 3D Modeling (All Configurations)
Pentium 4 or Athlon processor, 3 GHz or greater or Intel or AMD dual-core processor, 2 GHz or greater
4 GB RAM or more
6 GB hard disk space available in addition to free space required for installation
1,280 x 1,024 true color video display adapter 128 MB or greater, Pixel Shader 3.0 or greater, Direct3D®-capable workstation-class graphics card
3ds Max 2014 and 3ds Max Design 2014 are available for windows only:
System requirements for 3ds Max 2014 and 3ds Max Design 2014
Windows 8 or Windows® 7 64-bit Professional operating system
64-bit Intel or AMD multi core processor
4 GB RAM minimum (8 GB recommended)
4.5 GB free disk space for installation
3-button mouse
Latest version of Microsoft® Internet Explorer®, Apple® Safari®, or Mozilla® Firefox® web browser
Recommened Mac:
15-inch MacBook Pro with Retina display : 15.4-inch (diagonal) LED-backlit display with IPS technology
2880-by-1800 native resolution at 220 pixels per inch with support for millions of colors
Hardware
2.4GHz quad-core Quad-core Intel Core i7
16GB 1600MHz DDR3L SDRAM
512GB Flash Storage
Autodesk AutoCAD 2014 for Windows vs AutoCAD 2013 for Mac
USER INTERACTION Windows Mac
Command line
✓
✓
Multifunctional grips
✓
✓
Dynamic input
✓
✓
Auto-complete command entry2
✓
✓
Hide and isolate objects
✓
✓
Create and select similar objects
✓
✓
Delete duplicate objects
✓
✓
Properties palette
✓
✓
Quick properties palette
✓
Quick view
✓
✓
In-canvas viewport controls
✓
✓
Editable UCS icon
✓
✓
Layer tools3
✓
✓
Layer groups
✓
✓
Layer state manager4
✓
New layer notification
✓
Filter
✓
Quick select
✓
DesignCenter
✓
Tool palettes
✓
Content palette
✓
Navigation bar
✓
ShowMotion
✓
Coverflow navigation
✓
Multi-touch gestures
✓
AutoCorrect command entry
✓
File tabs
✓
DOCUMENTATION
Geometry creation & measurement tools
✓
✓
Parametric constraints
✓
✓
Associative arrays
✓
✓
Copy array
✓
✓
Object and layer transparency
✓
✓
Strike-through text
✓
✓
Blend curves
✓
✓
Multiple hatch editing
✓
✓
Sheet set manager
✓
Project manager
✓
Dynamic blocks5
✓
✓
Model documentation tools
✓
Table style editing
✓
Hatch creation preview
✓
Multiline style creation
✓
Digitizer integration
✓
Change space
✓
Express tools6
✓
Text align
✓
DESIGN
Solid, surface, and mesh modeling
✓
✓
Surface curve extraction
✓
✓
PressPull
✓
✓
Autodesk materials library
✓
✓
Material creation, editing, and mapping
✓
Basic rendering
✓
✓
Sun properties7
✓
✓
Visual styles7
✓
✓
Advanced rendering settings
✓
Camera creation
✓
Walkthroughs, flybys, and animations
✓
Autodesk ReCap point cloud tool
✓
Import Sketchup files (SKP)
✓
Geographic location
✓
CONNECTIVITY
External references (DWG)
✓
✓
Image underlays
✓
✓
PDF underlays
✓
✓
DWF underlays
✓
DGN underlays
✓
In-place editing of DWG references
✓
✓
Batch publish
✓
✓
Publish or plot to PDF
✓
✓
Plot styles
✓
✓
Plot style table editor
✓
✓
AutoCAD WS connectivity
✓
✓
Autodesk 360 connectivity
✓
Data links
✓
Data extraction
✓
Hyperlinks
✓
Markup set manager
✓
dbConnect manager
✓
eTransmit
✓
WMF import and export
✓
FBX import and export
✓
SAT import and export
✓
✓
Additional model import
✓
Design feed
✓
Share on Facebook
✓
LICENSING
Standalone licensing
✓
✓
Network licensing
✓
✓
Cross-platform licensing
✓

Video Advantage 2.0 problem

My problem here is that when I start up video advantage I see the same image in the local and remote window. This is also happening whenever I make a phone call as well. This is only happening to a few people. Any ideas?

Hello,
I have the same problem for CCM and CME with telephone 7941/61, when I use IP Communicator, VT works fine.
Is there any configuration for telephony 79XX different from Ip communicator?
CCM 5.1
CME 4.1 (IOS 12.4.15T)
Thanks,
Cassio

Cisco Unified Video Advantage - CDP Driver Not Installed- Windows 7 64-bit

OK, so I'm sure the problem is Windows 7 64-bit, but after installing version 2.1.2 of Video Advantage, although everything goes in with no problem... it's not connecting to either my CUPC soft-phone or the attached video enabled Cisco IP Phone . When I click on About, there is no version listed next to the CDP Driver Version. When I go into Device Manager, I don't even see the Cisco CDP Driver listed. There were no error messages during the install, but it would appear that the CDP Driver didn't get installed during setup. This, of course, would explain why the phones are not being detected (since it uses CDP for discovery).
Has anyone come across this and come up with a workaround ??

If you download the PDF for Cisco Unified Communications Support for Microsoft Windows 7 that was published on 10-22-2009 you will see that currently there are no plans to support Video Advantage on Windows 7. I haven’t tried installing it on my 64 bit Windows 7 system yet but have you tried installing it using the program compatibility wizard? If that doesn’t work you can install the XP Mode which is a virtual machine of Windows XP that would allow you to install it there. The XP Mode virtual machine has worked for me on every app so far that doesn’t work with Windows 7.

Video Advantage / CDP Problem

Dera All,
We have a problem with several Cisco IP Phones CP-7941G and the Video Advantage Software. The phones are running the SCCP41.8-3-3SR2S firmware but problem exists also with the SCCP41.8-3-3S firmware.
As far as I can see the phone does not send out CDP packets on the PC switch port. Within CSCsk11000 an error in the CDP implementation is described for the firmware version SCCP41.8-3-2SR1S.
Attached you find Wireshark Sniffer File describing the issue. A capture filter limiting the traffic source to the phone was applied.
Here are some comments what happened outside the wire:
Packet Comment
3 The phone was restarted to enable the settings access. It was then assured that not only in the Phone configuration on the CallManager (Version 6.01) CDP on the PC port was enabled but also on the phone itself. As you can see there are no CDP packets. Within the Video Advantage Software there is no connection between the phone and the camera.
4 The phone was reset. CDP packets are sent out immediately.
22 or 23 Within the Video Advantage Software the phone is connected to the camera.
In all our investigated cases a reset of the phone while the Video Advantage Software is running was successful.

I tried the three most recent versions
SCCP41.8-3-2S
SCCP41.8-3-3S
SCCP41.8-3-3SR2S
With all three versions VTA works if the phone was reset while the Video Advantage Software was running. After a while (between a day and a week) the phone stops sending the CDP packets and VTA is no more working at the next start. The SCCP41.8-3-2S version seems to be the most stable regarding this issue.
The mentioned bug does not fit as we run CCM6.
Thanks for your help.
Thomas

Camera for use with Cisco Unified Video advantage?

Cisco is EOLing the Cisco Unified video advantage product that we thought would be a good fit for us to integrate video with some of our IP Phones. I can still order the Video Advantage software until later in the year from Cisco but they have discontinued the Cisco VT Camera III that was previously used with this product.
They list the Logitech C920-C web cam as a replacement for this product, but it seems to be difficult to locate. The realease notes say you can use a 3rd party camera but Cisco does not officially support it.
Has anyone used any third party cameras with Cisco Unified Video advantage and if so which would you recomend. I was hoping to use the Logitech HD Pro Webcam C920 (the generic non Cisco version) but wasn't sure if it would work ok?
What do you think? This will be using Unified Video Advantage 2.3.
Jim

Hi,
We have been using Video advantage v 2.1.2 with 7940 series phone since long, it works fine with almost all 3rd party camera`s and even with the inbuilt laptop cameras.
v 2.3 is an enhanced version as compared the one which we are using. So i would suggest you to go ahead and try it with any good qaulity webcameras available in market.
Further to add there are certain PC requirements which needs to be met, the same can be found in the below link.
http://www.cisco.com/en/US/docs/video/cuva/2_3/release/notes/relnote_cuva23.html#wp1118706

Can't make Offnet Calls with Video Advantage on

I am no expert so I could be missing something basic. However, I have a Cisco phone that is logged in and is enabled for video. I installed the Video Advantage and all works well. I can make onNet calls with Video advantage on. However, I cannot make offnet calls. If I exit video advantage I can once again make offNet calls.
Any Ideas?
Ryan

Have you tried this:
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a0080569b65.shtml
Best regards.

Use two streams to manager client video/audio,Can i combine streams and record it with server AS API

Use two streams to manager client video/audio,Can i combine streams and record it with server AS API
I tried Stream.play()
var s=Stream.get("combine");
s.play("video");
s.play("audio",null,null,false);
s.record("append");
it's don't work!!

Thanks, that's what I had thought. Our domain.com zone is sourced internally and replicated to our advertisers for external users, so there's no way to change the result for internal vs external users.
This is a rudimentary question that I should already know but I sort of inherited this after it was built: Can I have users sign in with their email address ([email protected]) but under the hood, their SIP address is [email protected]? This would let users
sign in with an address they expect, but it would take advantage of the the local lyncdiscoverinternal record.
Thanks,
Matt

Cannot mke offnet calls with Video Advantage running

I have Video Advantage version 2.1.2. When I make an offnet call via an h323 gateway, I hear a fast busy and the called person hear the phone ring. When they answer the phone, they get dead air. When I close or disable Video Advantage, I have not problems with calls.

When running Video Telephony Advantage (VTA), outbound calls fail from Cisco CallManager through H.323 gateways to PSTN. An invalid bearer capability IE field is indicated in the release_comp message
http://www.ciscotaccc.com/kaidara-advisor/voice/showcase?case=K18460760
HTH
java
if this helps, please rate

Video Advantage OS supported

Hi,
I was wondering if Cisco Unified Video Advantage was supported in operating systems other than Windows?
Any help is much appreciated.

No. CUVA uses a Windows-only CDP driver to make that magic happen. Either way CUVA is EoS and it's functionality is being carried forward in the CUPC/Jabber products.

I tried to sync my iPod touch to a new laptop and it deleted all of my music and videos. I called tech support and they told me to email iTunes and they would give it back to me. How do I do this??

I tried to sync my iPod touch to a new MacPro laptop and it deleted all of my music and videos. I called tech support and they told me to email iTunes and they would give it back to me. How do I do this??

Correct. When you update via iTunes all synced media that is not in your iTunes library will be lost.
As IO said before:
You can redownload most iTunes pruchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store
I do not think it included audio books.

Need to convert music videos that are tagged as "Movies" and re-rag them as "Music Videos" to get them out of my movies library and into the Music Video folder. Likewise, I ha e some educational videos that belong in "Podcasts." Help?

Need to convert music videos that are tagged as "Movies" and re-rag them as "Music Videos" to get them out of my movies library and into the Music Video folder. Likewise, I have some educational videos that belong in "Podcasts." Help?

Select/highlight the ones that you want to change in your iTunes library, do Get-Info (control-I) and change their Media Kind on their Options tab to 'Music Video' - and then similarly for the podcasts.

Video advantage 2.0.2.0 and 7985

Similar Messages

Maybe you are looking for