Video card error - No resources when sound card installed.

Hi
I hope that someone can help me here :/
I just bought a x-fi Sound Blaster card... I installed it and booted up PC.. When windows loads the screen and colours are at their minimum.. I look in device manager and there is a yellow warning icon on the device (GeForce 6800 Ultra).. It says, unable to find enough resources, please disable another device in the system.. I disable the sound card and re-boot..no change.. I tried to go on the internet but the browser kept crashing.. I took the sound card out of the PC and everything is fine now.
Has anyone come across this before? I'd appreciate any help on this
Thanks
JonSince it's the sound card causing the problem, I thought it'd be ok to post here

Hi?Thanks for the replies... I've tried 4 PCI slots with no luck.. My AGP was already set to 256 ?One thing that I did notice was that after installing the SB software.. The test signal would only come through the left speaker... The speakers work fine with the on-board sound (which has been disabled btw).. I checked the settings and everything seemed as it should be...So this is either to do with the conflict or it's a faulty sound card.. IRQ's are a tricky subject for me.. There are lots of settings in the bios..Everything is set to auto currently. With the Sound Card out, the graphic card takes IRQ 6 (as told by device manager) in the bios it says it's assigned IRQ .. When the SB was installed, I forget what IRQ it had but I'm sure it was neither or 6.. Thanks for any further suggestions?Jon

Similar Messages

I'm getting an error code (A12E1) when trying to install Creative Cloud for photographers. Agraphers

I'm getting error code A12E1 when trying to install the Creative Cloud app for photographers. Can anyone help me get installed?

Hi Redrock,
Could you try the solutions described here:
http://helpx.adobe.com/creative-cloud/kb/a12e1-error-downloading-creative-cloud.html
Thanks,
-Dave B

Error about HKEY_LOCAL_MACHINE when trying to install QuickTime 7.2

This is the error I receive when trying to install Quicktime: "Could not open key: HKEYLOCALMACHINE|Software|Classes|QuickTimePlayerLib.QuickTimePlayerApp|CLSID. Verify that you have access to that key."
I have manually edited the Regedit permissions to include all, restarted the computer, and tried again... get the same Error message. I have also uninstalled both iTunes and QuickTime first, and used a Windows Cleanup utility.
Thanks, Merber

If you go to Start>Settings>Control Panel and open the User Accounts control panel. Does the account name that is being used to log onto the computer, appear in there as a Computer administrator? Also if you right click on CLSID go to Permissions>Advanced>Owner, is this account name showing up in there?

HT1925 I receive error code 2349 when trying to install iTunes. Any idea what that code means and how to correct?

receive error code 2349 when trying to install iTunes. Any idea what that code means and how to correct?

It's a better bet with a 2330, but the first thing I'd try with that is running a disk check (chkdsk) over your C drive.
XP instructions in the following document: How to perform disk error checking in Windows XP
Vista instructions in the following document: Check your hard disk for errors
Windows 7 instructions in the following document: How to use CHKDSK (Check Disk)
Select both Automatically fix file system errors and Scan for and attempt recovery of bad sectors, or use chkdsk /r (depending on which way you decide to go about doing this). You'll almost certainly have to schedule the chkdsk to run on startup. The scan should take quite a while ... if it quits after a few minutes or seconds, something's interfering with the scan.
Does the chkdsk find/repair any damage? If so, can you get an install to go through properly afterwards?

Getting error code A12E1 when trying to install CC update -- help! (Mac OS 10.7.5)

Getting error code A12E1 when trying to install CC update -- help! (Mac OS 10.7.5) I have disabled my security software, but that doesn't help. Any ideas?

http://helpx.adobe.com/creative-cloud/kb/a12e1-error-downloading-creative-cloud.html

Error code 0x80070BC9 when trying to install itunes

I'm getting error code 0x80070BC9 when trying to install iTunes

These ones are typically caused by underlying problems on the PC that also often cause Windows Updates to fail to install. If we can fix the Windows Update trouble, we can usually get the iTunes trouble cleaned up en passant.
Go into your Windows update and try to check for new updates. If updates install, stock up on the ones you're behind on, restarting the PC if requested to do so. After the restart, try installing iTunes again. Does it go through this time for you?
If windows updates fail to install, go into your Update History and doubleclick the failures. What alphanumeric codes appear for you? Are they also 80070BC9, or some other number? (If they're another number, what number are you getting?)

Error 1406 & 1603 when trying to install quicktine version 7

After installing the latest itunes upgrade and then having to install Quicktime 7 stand alone I get Error 1406 & 1603 when trying to install quicktine version 7.
My itunes no longer opens stating i do not have the latest version of Quicktime!!!
I spotted this on another thread but could see no answers
HELP!

hi Scooby2!
have you worked through this document yet?
Error 1406 or 1402 appears when you install iTunes or QuickTime for Windows
love, b

Error Code 80070005 when attempting to install KB2931356

After confirming that I am not an active victim of a virus or malware, I disable my Avast AV software and once again received Error Code 80070005 when trying to install Security Update for Microsoft .NET Framework 3.5.1 on Windows 7 and Windows Server 2008
R2 SP1 for x64-based Systems (KB2931356).
When I attempted to implement the solutions described in http://social.technet.microsoft.com/Forums/windows/en-US/61ce9777-aaac-41b5-ac02-eae76759d1d3/windows-update-error-80070005 and http://support.microsoft.com/kb/968003/en-us, which are slightly
different, I received the following output immediately after running the respectively prescribed Reset file.
I know not what to do next!
Any suggestions?
Thanks!
Jim

Yolanda,
Thank you very much for your concern and your assistance!
Unless you instructor otherwise, I will implement the following steps:
1. Download the System Update Readiness Tool from http://windows.microsoft.com/en-in/windows7/what-is-the-system-update-readiness-tool and run.
2. Shutdown PC.
3. Start PC.
4. Disable Avast Free A/V SW.
5. Install Security Update for Microsoft .NET Framework 3.5.1 on Windows 7 and Windows Server 2008 R2 SP1 for x64-based Systems (KB2931356).
6. Post outcome here.
7. If install fails, upload the cbs file (windows\logs\cbs) and windows update log (%windir%\Windowsupdate.log) here for further analysis.
Thank you, again, for helping me.
Sincerely,
Jim Kochanski
I followed all of the steps above.
When I went to install the update, seven were available and all seven failed (see below).
The log files were too large to cut and paste therefore you can find them at:
http://www.mediafire.com/view/vqm41z2bghb85fq/WindowsUpdate.log
http://www.mediafire.com/view/q9dc84kf6ftm31d/CBS.log
I was just wondering if anyone was trying to help me with this?
Thanks!
Jim

What does Error 1321 mean when trying to install Reader?

What does Error 1321 mean when trying to install Reader?

Hi ReadyToGo3 and welcome to the Adobe Reader Forums.
Please note you're not providing us with minimun info as to be able to assist you properly:
- What OS and version / What Browser and version,
- What Adobe Reader version / Is it a new install or an update you're being prompted to install
- A brief description of your problem (How & When), the exact error message you are receiving and steps already taken to try to resolve the issue.
Having said that, please note that error 1321 can occur for several reasons but mainly due to the installer not able to write a file due to a permissions issue or system error(s). To resolve the issue you may try to update the privileges on the parent folder of the file or source listed in the error message.
You may try helping yourself from here:
http://helpx.adobe.com/acrobat/kb/update-errors-acrobat-reader-windows.html#main_Update_er rors
Or alternatively:
http://helpx.adobe.com/acrobat/kb/quick-fix-install-download-reader.html#main__More_soluti ons
Lets us know how it goes. Good Luck!

Chimes, no video, no boot when video card installed. Cause?

Dual G5 2.0 (late '04?)
Used for 5 years, then system started suddenly powering off. Eventually wouldn't boot. Tried swapping out ATI X800XT vid card for a 9600 (both AGP) & it worked again for a couple days, then wouldn't boot again. Put it aside for a while, came back to it yesterday, and came to these conclusions:
1) with X800XT installed, the system (PSU) clicks once, then nothing. no chime, no lights, no fans.
2) with 9600 installed, it chimes, power light on & steady, fans start, I hear the HDD click once, then nothing. no video out. eventually the fans go into overdrive.
3) WITHOUT a video card, it chimes, light on, fans OK, and I hear the HDD running through what I assume to be a boot sequence.
4) I have reset the PMU and replaced the battery. Also tried CMD-CNTL-O-F. Nothing.
Thinking it might be the power supply? Where do I go from here to diagnose the cause?
If it's the logic board, I'll tear out the guts & sell on ebay. If it's the PSU, I've read about someone replacing it with a standard PC ATX supply (don't want to spend the $$ for a G5 PSU.)
Thanks for any suggestions!

OK, assuming you have file sharing enabled, when you bring the machine up without video card, can you connect to it from another computer on the same LAN?
The fact that either video card blocks the boot is suggestive of maybe a power supply problem, though in my experience an overload condition perceived by the power supply will result in a click from the supply and the machine powering down completely.
That was a situation I had some time ago before replacing the supply. What would happen was that in a non-safe boot, when the kexts for the Ultra6800 loaded, the current draw would increase and the supply would trip itself off. (Puzzling mystery solution revealed just now in formulating the reply. Thanks.)
That being said, the fact that safe boot doesn't help plus the other differential symptoms between the cards really does suggest a failing power supply. A new supply around the web is on the order of $200, but there are plenty of used ones on eBay for much less, occasionally even a new one goes at a bargain.
One thing you could do is blow the probably well-stocked dust supply out of the power supply. Better to remove and do that outside, but you can make something of a dent with the power supply in the enclosure. Just be sure to do it outside, because the dust that can come out will probably be pretty nasty. (Of this I have personal experience!) Of course, under what you have reported, this has a slim chance of actually helping.

Constant loud piercing beep upon startup when GeForce88000 GT video card installed.

I purchased a 2008 2.8 GHz Mac Pro that has a Quadro FX 1800 Windows video card and Windows 7 installed .
OSX not re-installed yet (I'm trying to get there).
So I installed a GeForce88000 GT video card, which is listed as compatible with this machine for Mac OS, and immediately upon power up, and I mean before I can even pull my finger back out after pushing the button in, the beep starts (and never stops).
This occured when I had both cards installed and when I only had the Mac GeForce88000 GT installed (in that customary first slot).
When I had both cards installed, Windows booted up normally, there was just this unglodly screeeching beep providing a certan "vibe" for the proceedings.
Windows still verifies all 16 GB of RAM.
I tried to search for other posts regarding this issue but came up empty.

Don't care what Nvidia says.
It needs aux power.
All performance PCIe cards need aux power.........
The following photograph shows a comparison to two other cards. The GeForce 8800 GT (left) is about the same size, and also uses a single-slot cooler. The previous generation Radeon X1900 XT (right) is somewhat longer due to its fixing frame. (Note that the cooler on the X1900XT is not the original one, but as the original it's a two-slot cooler). All of these cards need auxiliary power, the power connectors are on the bottom right on each card.
http://www.xlr8yourmac.com/graphics/ati_3870_mac_pc_review/radeonhd3870_review.h tml
Don't have a cable? Get one:
http://www.ebay.com/itm/Mac-Apple-6-pin-Power-Cable-7800-GT-GTX-8800GT-GTX-285-/ 280414703219?pt=US_Power_Cables_Connectors&hash=item414a04ce73#ht_1326wt_840

Cannot view video get error message and only sound.

cannot view video, get error message and sound only. Message Error Code:c000005, address:2568b7ab

I am just finally posting a reply. Looks as though the sound card went out. I was told that I could purchase a new open and install myself. I did not do that, but rather my step-dad just decided it was time to buy a new Mac Mini.

How do I get my NX6600GT-TD128E (PCIE) video card installed on a K8N NEO4-F Mb ?

I have received two new NX6600GT-TD128E (MS-8983) vdeo cards to install on my new K8N NEO4-F (MS-7125) motherboard flashed with BIOS ver 1.B.
First video card turned out to be bad. The replacement card allows view of bios screens and post screen, but when Windows XP (pro) starts up, the video goes blank and Windows XP locks up dead.
Any suggestions as to what I need to do to get the video card up and running?

Quote from: macprmgr on 19-March-06, 11:23:16
I have received two new NX6600GT-TD128E (MS-8983) vdeo cards to install on my new K8N NEO4-F (MS-7125) motherboard flashed with BIOS ver 1.B.
First video card turned out to be bad. The replacement card allows view of bios screens and post screen, but when Windows XP (pro) starts up, the video goes blank and Windows XP locks up dead.
Any suggestions as to what I need to do to get the video card up and running?
Can you tell us what other parts you have
Please read and comply with the Forum Rules.
I know you want the problem fixed but its hard to help if we don't know the basic's. Check the rules you will find they are a good place to start and for you to help yourself as well as others have an idea to help you

Mid 2007 24" imac only boots without video card installed

, do i need a new one or is it something else?
one day it decided to not boot. No chime, black screen. Can hear fans and cd/dvd spin. Diag. leds 1,2&3 lit 4 is not. Did some googling, and eventually found out that if i take the MMX ATI 2600HD video card out of the computer and turn it on, it boots up fine (still no chime however) and i am able to use screen sharing from my other mac to access it. Everything looks and works as normal, only there is no screen of its own. the keyboard wors fine, mouse, cd/dvd drive etc. I have already purchased and installed a new PSU at $120 which did not fix a thing, so i am hesitant to just assume that buying a new video card will solve my problem. so my first question is, will buying and installing a new video card fix it? and if so can i purchase an upgraded video card other than the stock ATI 2600HD? i have heard that there is an NVIDIA card that is compatible a GeForce 8800 GS 512MB i believe. and third, if it is compatible, will it work with the Heatsink for the ATI 2600HD or do i need to buy that as well??
I am trying to avoid the BS canned answer that apple loves to give as a solution, which is replace the logic Board. At nearly $1,000 I'll spend my time and effort it may take to actually find the reason it broke and attempt to fix it rather than just replace the whole thing with a new one. any suggestions or advice graetly appreciated.

so, a strange development on my imac problem. I have ordered a new video card for it, a 2600hd pro. today out of curiosity i punched the numbers i could find from the card that was in there and it comes up as a ati 2400xt card. that card was the one for the 20" model not my 24". whats up with that? does that mean that when my new 2600hd pro gets here it will not work in my system? I sure hope so or apple has some splaining to do!

Video Card install problems

I have been having problems getting past the video card setup. I have a ATI Rage Pro 8m/b, whenever I select it as an option and test it (or any other card in the family like xpert@play ) the xserver reports it could not find a mach64 controller. The only way I can get the install to complete is to use the generic 64x480 16 colors driver. Now that it is installed and semi-working, could someone let me know how I can change the driver after the O/S is installed. I have not patched the O/S yet.
-Chris

If "dtlogin" is running, stop it with "Options" ->
"Command line login". Login on the text console
as user "root", then run "kdmconfig" to configure
the video card.
When you logout from the text console, dtlogin is
restarted automatically with the new settings after
10-15 seconds.

Video card error - No resources when sound card installed.

Similar Messages

Maybe you are looking for