Video playback change from iTunes9

Watching a video (Movie, TV Episode, Podcast) in iTunes9 I was able to hit the spacebar [to pause] then hit 'esc' to get back to a standard iTunes window.
In iTunes10, when I hit the 'esc' key, the video seperates off from iTunes so I have to close that to get back to my iTunes window.
How can I get back to the two key combo I used to do. This was majorly handy when watching a podcast on my laptop so I could quick switch to a browser to check something, or switch over to another application.

yea, this is annoying. quicktime issue maybe?

Similar Messages

  • How can i monitor network traffic to debug video playback issues from a NAS?

    I am having problems playing videos on my new Mini that i am using as an HTPC. 
    I have a brand new Mac Mini running Lion with a 2.7 i7 processor and 8GB of RAM with a wired connection to a switch. .
    My switch is a NETGEAR ProSafe GS108T-200NAS set to default settings. I haven't had a chance to start messing with VLAN settings or anything else. There is a bit of a learning curve on my part on this end.
    My NAS is a ReadyNAS Pro (RNDP6000) with 3 x 1 TB hitachi ultrastar (HUA722010CLA330) drives and a 1.5 TB seagate (ST31500341AS) drive setup in RAID config using X-RAID2.
    The problem I am having is video playback when accessing large video files off of the NAS.  These are typically 1080 HD mkv files. 
    I have tested movies as small as 7.5GB with only slight stutters on occasion.  I tried a 10.5GB movie and the stalling was much more pronounced. Movies larger than 11GB are completely unwatchable stalling every minute or so. 
    I have also tried large movies on the local drive and that is not a problem at all - they play back just fine.  Beautiful playback in hidef.  Mind you, some of these are the same files that were stalling over the network.
    I have also noticed that some other network devices get kicked off the network when a movie is playing.
    I think it has something to do with the transfer speed of files over the network and the switch - i am no expert at this mind you.
    I am wondering if there is some sort of utility that i can use to monitor network activity on the mini so that i can fix my problem.  Or has anyone made chages in their switch settings to optimize data trasfer speeds.
    Any advice or recommendations on. 
    Thank you all!

    OK, I did a couple of things and ran things a couple of times. 
    First what I did settings wise:
    I enabled jumbo frames on the Mac Mini, ReadyNAS Pro, and the Netgear GS108T switch.  All with MTU set to 9000.
    I went ahead and enabled jumbo frames on the rest of the computers on the network just in case.
    After these changes I ran into the same problems with videos timing out - very annoying and frustrating as you can imagine.
    Then I started playing with device configurations.  My original configuration was NAS > Netgear switch > Mac Mini. I went ahead and switched the switch to an Airport Extreme I have as my WAP and the setup looked like this - NAS > Airport Extreme > Mac Mini. 
    Well, long story short, no go.  It appears to me that the NAS is the one having issues providing the necessary data at the proper speed.  I also tried playing sopme movies off of the NAS onto a desktop i have and had the same issues - choppy frames and crashing movies.  I even tried connecting wirelessly to see if that would work. 
    BTW, I have the Mac accessing the file system using CIFS. 
    I don't know what else I could do.
    I am going to have to go to the Netgear forums to see if i can figure this out.  Hopefully, I can get things going to be able to help some people out.
    If anyone has any ideas, they would be greatly appreciated.
    My only other alternative is spending $2000 for the thunderbolt capable NAS that Apple sells - it's only money!
    Cesar

  • Video Rate Changes from Cinema Tools to Final Cut

    I have a problem that exists on serveral levels. Hopefully I can explain:
    1. I directed a concert shoot with eight cameras. All cameras were Panasonic DVX100A configured for 24p Advanced except one, which was a Panasonic SDX900 configured for 24p (which I later discovered was laid down with a 3:2 pulldown instead of a 2:3:3:2 advanced pulldown like the DVX100A cameras).
    2. It was planned from the beginning to use the multiclip feature in FCP to edit the footage.
    3. The tapes from each camera were captured from beginning to end—about an hour each tape, four tapes per camera—at full resolution, the pulldown was removed, and the clips were then recompressed to Photo JPEG EXCEPT the tapes from the SDX900.
    4. When I finally figured out that the footage from the SDX900 used a 3:2 pulldown, I opened the captured clips in Cinema Tools and attempted to remove the pulldown. The problem I ran into there was that CT can't handle files larger than 9 GB. Each captured clip (four of them—one for each tape) ranged between 10 and 13 GB.
    5. My solution to this was to open each clip in QuickTime Pro and split the clip in half, open each half in CT and remove the pulldown on the smaller files, then open the smaller halves in QT again and join them back together into a single clip.
    6. When I open the new master clips in Cinema Tools and analyze them, the video/frame rate is 23.98 as expected. BUT, when I import the clips into Final Cut Pro, the video/frame rate is 29.97 and I can't understand why. If I try to do a pulldown removal (again) from FCP, it doesn't work—I get an error that it can't find a clip with a pulldown to remove (duh!).
    Is this a bug, and is there any way to fix this and make it work? I need to make all of the assets available for my class at school.

    I have a problem that exists on serveral levels. Hopefully I can explain:
    1. I directed a concert shoot with eight cameras. All cameras were Panasonic DVX100A configured for 24p Advanced except one, which was a Panasonic SDX900 configured for 24p (which I later discovered was laid down with a 3:2 pulldown instead of a 2:3:3:2 advanced pulldown like the DVX100A cameras).
    2. It was planned from the beginning to use the multiclip feature in FCP to edit the footage.
    3. The tapes from each camera were captured from beginning to end—about an hour each tape, four tapes per camera—at full resolution, the pulldown was removed, and the clips were then recompressed to Photo JPEG EXCEPT the tapes from the SDX900.
    4. When I finally figured out that the footage from the SDX900 used a 3:2 pulldown, I opened the captured clips in Cinema Tools and attempted to remove the pulldown. The problem I ran into there was that CT can't handle files larger than 9 GB. Each captured clip (four of them—one for each tape) ranged between 10 and 13 GB.
    5. My solution to this was to open each clip in QuickTime Pro and split the clip in half, open each half in CT and remove the pulldown on the smaller files, then open the smaller halves in QT again and join them back together into a single clip.
    6. When I open the new master clips in Cinema Tools and analyze them, the video/frame rate is 23.98 as expected. BUT, when I import the clips into Final Cut Pro, the video/frame rate is 29.97 and I can't understand why. If I try to do a pulldown removal (again) from FCP, it doesn't work—I get an error that it can't find a clip with a pulldown to remove (duh!).
    Is this a bug, and is there any way to fix this and make it work? I need to make all of the assets available for my class at school.

  • Portege R700 - Issues with video playback with resolution over 360p

    I've got this video playback issue from day one. While for instance on YouTube, videos with resolution above 360p freeze up while the sound is ok.
    I've contacted Toshiba through which I got a linke to the latest bios and drivers. After the upgrade issue persists. I sometimes get a green screen while watching flash video as well. I'm guessing this is a graphic card hardware issue. Any ideas? Thanks! (Portege R700 19L, win7 pro 64)

    Hello
    Have you tried watching videos in high performance mode and tested different Internet browsers?

  • Video playback fullscreen

    While watching a video in full screen mode I press the pasue button and the whole movie window fades out and disappears. The normal functionality would be for the movie to pause. The movie then stops. No window or anything.The only way to start the movie back up is to go into itunes and restart the movie.

    Don't know what's going on there...works here with two Cinema Displays.
    I've got Apple FireWire NTSC (mirror on desktop-checked) in my A/V devices tab of Audio/Video Settings...(nothing selected in 'Different Output for Edit to Tape/Print to Video, because I'm not using that function in this workflow)
    I can then just go to View/Video Playback/Fullscreen from the main menu and it goes right out to my second display.
    Maybe has something to do with your Mac System Monitor preferences.?.?...not sure.
    K

  • Video Playback Fullscreen (missing)

    I recently took my iMac in to have the logic board replaced, which was quick and painless, by the way, but when I got back to work on it, the Command-F12 -Fullscreen preview wouldn't work. Under the Preferences menu, the video preview option comes up (missing). Any Ideas? thanks!

    Don't know what's going on there...works here with two Cinema Displays.
    I've got Apple FireWire NTSC (mirror on desktop-checked) in my A/V devices tab of Audio/Video Settings...(nothing selected in 'Different Output for Edit to Tape/Print to Video, because I'm not using that function in this workflow)
    I can then just go to View/Video Playback/Fullscreen from the main menu and it goes right out to my second display.
    Maybe has something to do with your Mac System Monitor preferences.?.?...not sure.
    K

  • Apple TV 2 choppy video playback when mirroring from Macbook Pro (Yosemite) and Macbook Air (Yosemite) but not iOS devices

    Video playback is choppy (cuts out every 30-45 seconds) when air playing from both my MacBook Air 1.3 GHz Intel Core i5 running Yosemite and my husbands new MacBook Pro, but runs perfectly when mirroring from any of our iOS devices (iPhone 6+, iPad mini 3, etc.) We have Apple TV 2. This problem just started a few weeks ago, was working fine around Christmas. The problem seems to have coincidentally started right after our son tried plugging in and setting up his Chromecast on our tv. I disconnected the Chromecast, but we still have the problem. All of our software if up to date and I've tried disconnecting blue tooth, we do not have a microwave and our wifi network has a very strong signal. We have an Airport Extreme base station. Is there a solution to our problem?

    Hi leahmturner,
    I see that you are experiencing an issue with choppiness while AirPlay Mirroring from your computers to your Apple TV. I have an article that contains some helpful troubleshooting steps for you regarding this issue:
    About AirPlay Mirroring in OS X - Apple Support
    http://support.apple.com/en-us/HT201343
    Optimizing image quality
    Resolution matching modes
    You can choose between two desktop resolution matching modes that let you select which display will have the best image. When AirPlay Mirroring is turned on, select an option under "Match Desktop Size To:" in the AirPlay Mirroring menu extra.
    Match Desktop Size To: Apple TV
    AirPlay Mirroring changes the desktop resolution to best match your Apple TV, resulting in a 16:9 image that fills the HDTV screen. This setting often produces the sharpest image on the HDTV. The aspect ratio and/or resolution of the built-in Mac display may change to accommodate the Apple TV.
    Match Desktop Size To: This Mac
    AirPlay Mirroring scales the contents of the desktop to fit on the Apple TV, leaving the resolution of your Mac's display unchanged. Use this setting for the sharpest image on your Mac's display. Depending on your Mac model, the resulting image may not fill the HDTV screen.
    Troubleshooting AirPlay Mirroring
    If you don't see mirroring options
    If your Mac and Apple TV are on the same network, but no AirPlay Mirroring menu appears, your Apple TV may be asleep. Simply press a button on your Apple TV remote to wake it up. After a few seconds, the AirPlay Mirroring menu extra appears. If you still don't see the options you expect, make sure your Apple TV has the current software update installed. Also make sure that you have the "Show mirroring options in the menu bar when available" option selected in the Displays pane of System Preferences.
    If the menu bar or Dock is cropped
    Some HDTVs have bezels that cover a small percentage of the screen. This can result in a slight cropping of a full-resolution HDTV image. Depending on the HDTV model, AirPlay Mirroring may automatically adjust the picture size to prevent cropping.  If you are using OS X Mountain Lion or later, and you see cropping of the menu bar or Dock when using AirPlay Mirroring, toggle the Overscan correction option in Displays preferences.
    Minimize video post-processing
    HDTVs often apply picture quality enhancements intended to improve the look of film and video sources. In some cases, these enhancements can lead to over-sharpening artifacts when displaying your Mac desktop. Some HDTV models have built-in settings to change or disable the enhancements for use with a computer (computer, presentation, or game modes). Otherwise, the controls for sharpness, detail enhancement and noise reduction can be used to optimize the appearance of the Mac desktop. Consult your HDTV’s manual for guidance on the appropriate settings for use with a computer.
    Firewall security settings
    If you use a firewall, make sure the following firewall security options have been set to allow AirPlay Mirroring to work:
    Choose System Preferences from the Apple menu ().
    Click Security & Privacy, then click Firewall.
    Click the lock icon to unlock it if it's locked, then type an administrator name and password.
    Click Firewall Options.
    Deselect (uncheck) the “Block all incoming connections” checkbox.
    Select (check) the “Automatically allow signed software to receive incoming connections” checkbox.
    Thanks for coming to the Apple Support Communities!
    Regards,
    Braden

  • I just moved my itunes library from a win 7 computer to a win 8.1 computer. Getting an error message "iTunes has detected a problem with your audio configuration. Audio/Video playback may not operate properly. Can't play CDs or get audio file from web!

    Help! I just moved my itunes library from a Win 7 computer to a new Win 8.1 computer following the instructions on the itunes website. Everything is good except I'm getting an error message on the Win 8 computer if I try to play a CD or get an audio file off of the internet. I get an error message that says "iTunes has detected a problem with your audio configuration. Audio/Video playback may not operate properly. I don't know where to look for or fix the audio configuration on the win 8 computer. As far as I can tell the iTunes configuration looks the same as on the other computers in the house. At this point I don't dare plug my ipod touch into the Win 8 computer for fear it will get messed up.

    I have the same problem and I know that it is due to my PCI Audio driver not being compatible with WIndows 8.1.
    iTunes isn't the only program that can't direct sound to the built-in speakers anymore. The obvious solution would be to update the drivers, but unfortunately Dell does not provide an updated driver for my model, so I am stuck with that.
    However, saying that, only my laptop speakers are affected by this. I can use sound fine on applications where I can choose the output device and direct sound to the head phones, but for some reason iTunes does not let you choose the audio device manually.
    To listen to music I imported the iTunes Library in Windows Media Player and changed the audio output using the following instructions: http://windows.microsoft.com/en-us/windows7/c00d11ba
    However, I would also like to rent movie's from iTunes, 
    Would be great if iTunes would let you choose the output device, too, like most other applications using sound  from Skype to Windows Media Player,...

  • Video frame rate change from video to video

    HI all ,
    when I use labview 2013 I found some strange in acquiring avi video
     when I acquire video from my computer the fps change from video to another one
    some video fps reach 800 fps and other reach 180 fps what is the problem 

    A lower frame rate is actually expected behavior if you are playing video through LabVIEW. This KB explains that LabVIEW analyzes the video one frame at a time and keeps it in the system memory on the CPU.  This can result in slower frame rates during playback. If you would like to simply view video through your front panel, it may be a good idea to embed Windows Media Player in the VI through an ActiveX control.
    -Erik S
    Applications Engineer
    National Instruments

  • Video playback from Final Cut Pro studders over HDMI

    I have a problem playing back video from FCP. The video output will studder during horizontal pans when I output via HDMI. The audio output is not affected.
    I have been playing video successfully using FireWire for output in FCP, however, my new video switcher system will not support FireWire output.
    What are some possible causes of this problem?
    System stats:
    * Mac Mini (2010 model)
    * 8GB RAM
    * OS X 10.6.4 (Snow Leopard)
    * Final Cut Pro 7.0.3 (Final Cut Studio 3)

    @ Studio X : The files were originally created with Final Cut Pro, rendered out to QuickTime, then are being played back with Final Cut Pro. The file that has the most noticable studdering is a 60-minute timeline sequence in Final Cut. All files are being stored and played back from the Mac Mini's internal hard drive. Everything was originally shot on DV and formatted for a 4:3 aspect ratio.
    @ Shane Ross : Are there any settings in the MacOS or FCP where I can improve the HDMI video signal? Or do you know of / have any experience with Firewire to HDMI converters? Unfortunately, my new signal path relies on HDMI from the video playback.
    My current setup uses the Firewire output, which is then converted to composite video & analog audio using a pair of ageing DV tape decks. That setup is becoming troublesome due to age.

  • How do I stop my itunes video playback from skipping

    We just bought a full season of a show and while trying to watch it the video playback is either really slow or it stops and skips while the audio keeps playing. Any suggestions how to fix?

    Try:
    - Reset the iOS device. Nothing will be lost      
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Unsync/delete all music and resync
    To delete all music go to Settings>General>Usage>Storage>Music>Tap edit in upper right and then tap the minus sign by All Music
    - Reset all settings                            
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:                                               
    iOS: Back up and restore your iOS device with iCloud or iTunes
    - Restore to factory settings/new iOS device.                       

  • Apple TV speeds up video playback on files ripped from DVDs - it looks like it's being fastforwarded slightly.

    I just set up my Apple TV 2, only to find playback issues from the start.
    Whenever I try to play videos from iTunes, the playback is noticeably faster than it should be. It's almost as if the video is slightly sped up, and the audio is in sync with this. The aspect ratio is also very different on some of these videos (and this doesn't correct on my TV as it does on my laptop screen) - by which I mean that the picture appears stretched on some, but not others. These are files I have ripped from my DVD collection.
    What can I do about this?

    Ok, now I understand.
    I haven't directly used those digital copies, per your original post it sounds is as it plays fine in iTunes but just not on apple tv
    Here is the compatibility list for ATV2, in iTunes right click and get info for one of the files to see if it falls within
    H.264 video up to 720p, 30 frames per second, Main Profile level 3.1 with AAC-LC audio up to 160 Kbps per channel, 48kHz, stereo audio in .m4v, .mp4, and .mov file formats
    MPEG-4 video, up to 2.5 Mbps, 640 by 480 pixels, 30 frames per second, Simple Profile with AAC-LC audio up to 160 Kbps, 48kHz, stereo audio in .m4v, .mp4, and .mov file formats
    Motion JPEG (M-JPEG) up to 35 Mbps, 1280 by 720 pixels, 30 frames per second, audio in ulaw, PCM stereo audio in .avi file format

  • Aperture Video Import Problem - from Lumix GH4: Imported clips have their dates changed to the import date.  The files show up on the hard drive but many are not showing up in Aperture.

    Aperture Video Import Problem - from Lumix GH4: Imported clips have their dates changed to the import date.  The files show up on the hard drive with import date not created date, but many of these same files are not showing up in Aperture. Sometimes the clips actually show up with the current import but take on the video information from a previously imported file.

    It was suggested I move this question to IPhoto or IMovie which I did. 
    Well moving to a different discussion group did not provide an answer to this question either. But what I finally did was import one batch of photos and videos into IPhoto for a given day at a time. Working with these I could change the date and times in order to get them in the original sequench taken. Then I would create an album with that batch. These would all be on the same day (IMove was closed for this phase). Then I would open IMovie, generate the thumbnails for that album, and select the album I had created. This was necessary because the importing process in IPhoto was using incorrect dates for my video so it was a real struggle finding them in IMove until I developed this approach.
    I believe that this whole process was so screwy because I was importing from an external hard drive not a camera. I had these photos on a PC and did not have the original cameras to use to import directly which I am fairly sure would have made this easier!

  • Video playback in Oracle 10g , Video JavaBean or playing video from a file

    Hi, I am making an online encyclopaedia using Oracle Forms 10g and was wondering whether it is possible to have video playback from files on my computer or on a database.
    Is there a way of linking forms at runtime to the file on my harddrive and playing via windows media player?
    Or can anyone suggest anything similar such as video javabeans etc.
    I am using Windows XP not NT/2000 so intermedia is not an option.
    Thanks

    Hello there,
    In Forms 6, one could use an OLE container which could be populated with an actual Windows Media Player object for video playback. Unfortunately being on 10g means the OLE objects are gone too... the best bet is to find a bean or pluggable java component that minics the functionality. There must be one on the web somewhere if you do a bit of searching!

  • Fullscreen Video Playback, from Button? Video Question

    I have used the external URL to link directly to a video and it opened in an HTML window, not just fullscreen.
    I would like to emulate what is seen in this example.
    LINK:
    http://youtu.be/-YMyQZki0bY?hd=1&t=1m2s

    So after some experimenting, I was able to get what you suggested to work. Interesting method.
    Is there a way to edit the media container to load from external URL while the interaction looks the same to the user?
    I tried to:
    1) Place media on stage (MP4)
    2) With the MP4 placed and selected, use the MEDIA panel to change the poster to NONE.
    3) Still in the MEDIA panel with MP4 selected, click "Place a Video from a URL" and type in URL of external MP4.
    I figured this would just swap the source, but no. It didn't work correctly.
    So, now I have two choices to show video that I can make work.
    EXTERNAL VIDEO:
    Open URL from button, straight to MP4. Opens in HTML window, so the look isn't the cleanest.
    INTERNAL VIDEO:
    Place video on page.
    Select video and then MEDIA panel.
    Choose NONE for poster image.
    You can put an image behind this "container" or place it atop something that looks like a button and clicking it will trigger the video.
    Correct?

Maybe you are looking for