Video playlife too short

I just recently returned my iPod because the video life was too short. What I mean by this is whenever I would watch a video the battery is always depleted whenever I finish. When I sent it back to Apple, they said that there was no problem with it. But, clearly there is a problem if my iPod dies everytime I watch a video. Its also funny how it took Apple 5 days ,after shipdate, to figure out that my iPod had no problems!? To me, this is too confusing so any help will be appreciated!
Windows Windows XP

How short are we talking here? Videos drain the battery very quickly. When I can't sleep, I sometimes watch an episode of South Park. They're about 20 minutes long and whenever I finish, the battery is nearly always in the red no matter how full the charge was previously.
That said, there are a number of steps you can take to ensure you're getting the most out of your iPod. Have a look at Apple's iPod battery page:
http://www.apple.com/batteries/ipods.html

Similar Messages

Is LED display video cord too short to use with Mac Pro?

I've seen the new 24-in cinema display used with a macbook and noted how short the cord is. Now I'm thinking of getting the new Mac Pro with that same display but won't the cord be too short for me to set the tower near the floor on the side of my desk? I don't want to have to set that tower ON my desktop just so the connector will reach the minidisplay port.
Any thoughts?

I have exactly this set up, and it (just) works for me.
The cable is about 42" from the back of the monitor to the three connectors at the other end, which allows me to have the Mac Pro on the floor, and the monitor on my desk. Obviously, it will depend on your desk height, cable access, etc., but it was a bit of tight fit, so you might want to get out a tape measure and see it will work for you.

Video scrubbing too coarse

I have a collection of mp4 videos that are relatively short (less than 10 secs) and want to have finer control when scrubbing. The scrubbing on Quicktime Player is exactly what I want. Is there some way to get MPMoviePlayerController to give me finer control? On the iPad scrubbing seems to operate in 1 second increments, but on the Mac Quicktime Player I get per frame control.
Thanks
Hank

I have tried this. The drop down only ever shows "Hi Speed Scrubbing". My guess is the the videos are too short for the half/quarter/fine stuff to kick in. I do see the other options when viewing a longer video. Could this be a property of the video?

Premiere Pro CC 2014 Video is too LARGE

Hi all,
Just getting started with Premiere Pro CC 2014. I've imported a short clip to practice on, and the first thing I noticed is that the output video is too large for the screen:
Is there a way to fix this?
I don't know if this is related or not, but I also keep getting this:
It says the minimum screen resolution required is 1024 x 768. My screen resolution is 1366 x 768. Isn't that large enough?
Any help would be great - thanks!!

I think I've figured out the scaling issue. Any ideas on the screen resolution would be awesome.

Burn failure because "Video Bitrate Too High"

Hi all, I'm trying to burn a dvd with 10 short films on it and just got this error:
Starting DVD Build TESTING_DVD...
Compiler Initializing...
Precompiling Project TESTING_DVD
Compiling VMG Information...
Created 25 PGCs in VTSM1
Created 5 PGCs in VTSM2
Created 13 PGCs in VMG.
19 Menu(s) will be created...
Compiling Menu PGCs...
Compiling Menu#1 (Ravens)...
Rendering Menu:Ravens,Language:1...
Compiling Menu#2 (Cowboys in Kosovo)...
Rendering Menu:Cowboys in Kosovo,Language:1...
Compiling Menu#3 (Red Rubber Boots)...
Rendering Menu:Red Rubber Boots,Language:1...
Compiling Menu#4 (Images From the Corner)...
Rendering Menu:Images From the Corner,Language:1...
Compiling Menu#5 (House of Wisdom)...
Rendering Menu:House of Wisdom,Language:1...
Compiling Menu#6 (A Conversation with Haris)...
Rendering Menu:A Conversation with Haris,Language:1...
Compiling Menu#7 (Its Only Mine)...
Rendering Menu:Its Only Mine,Language:1...
Compiling Menu#8 (I Don't Know Where)...
Rendering Menu:I Don't Know Where,Language:1...
Compiling Menu#9 (Father, Son, Holy Ghost)...
Rendering Menu:Father, Son, Holy Ghost,Language:1...
Compiling Menu#10 (Menu 1)...
Rendering Menu:Menu 1,Language:1...
Compiling Menu#11 (Menu 3)...
Rendering Menu:Menu 3,Language:1...
Compiling Menu#12 (About AMMAM)...
Rendering Menu:About AMMAM,Language:1...
Compiling Menu#13 (Zel bio)...
Rendering Menu:Zel bio,Language:1...
Compiling Menu#14 (Roberto bio)...
Rendering Menu:Roberto bio,Language:1...
Compiling Menu#15 (Corrine bio)...
Rendering Menu:Corrine bio,Language:1...
Compiling Menu#16 (Jasmila bio)...
Rendering Menu:Jasmila bio,Language:1...
Compiling Menu#17 (Sheila bio)...
Rendering Menu:Sheila bio,Language:1...
Compiling Menu#18 (HoW statement)...
Rendering Menu:HoW statement,Language:1...
Compiling Menu#19 (CiK statement)...
Rendering Menu:CiK statement,Language:1...
Writing VIDEO_TS.VOB
Compiling Menu PGCs...
Writing VTS020.VOB
2 VTSs and 12 Titles will be created...
Compiling VTS#1 (Animation demo)...
Muxing VTS011.VOB
Done.
Compiling VTS#2 (Play All)...
Writing VTS020.VOB
Muxing VTS021.VOB
Video Bitrate Too High
Build cancelled
Formatting finished.
Building was not successful. See log.
Does this mean the first film in the Play All track needs to be adjusted? Or that they all need to be adjusted? And adjusted to what? They fit on the disc in terms of space. Please help!
Message was edited by: ErinSayHi

Hi.
I'm having a similar problem here.
This is the log I get:
Starting DVD Build DEMOREELOMARVELAZQUEZ...
Compiler Initializing...
Precompiling Project DEMOREELOMARVELAZQUEZ
Parsing Assets...
Encoding Assets...
Compiling VMG Information...
Created 7 PGCs in VTSM1
Created 5 PGCs in VTSM2
Created 14 PGCs in VMG.
1 Menu(s) will be created...
Compiling Menu PGCs...
Compiling Menu#1 (Menu Principal)...
Writing VIDEO_TS.VOB
Compiling Menu PGCs...
Writing VTS020.VOB
2 VTSs and 4 Titles will be created...
Compiling VTS#1 (Pizarra Lúdica Omar)...
Muxing VTS011.VOB
Done.
Compiling VTS#2 (Track Spots)...
Writing VTS020.VOB
Muxing VTS021.VOB
Video Bitrate Too High
Build cancelled
Formatting finished.
Building was not successful. See log.
This is a project that I already had burned to DVD with no problems whatsoever, but I recently moved from OSX 10.4 to OSX 10.5 and also moved from DVDSP 3 to DVDSP 4 and there my problem began. At the moment I have 768mb of RAM and I'm aware that DVDSP 4 is asking me for at least 1gb to work properly. Would the RAM be the problem?.
I hope you can help me out.
Thanx.
Omar

My nouveau driver file is too short? [Solved]

Yesterday I had this error when I was starting Xorg and it said my file was too short in the Xorg.0.log. I changed the device driver in my xorg.conf to "nouveau". (I do have a NVDIA card and nouveau is installed.)
I have this youtube video to document the error. (It still doesn't work but I changed the device driver to "fbdev")
(Yes, I am young! Please don't make fun of me!)
https://www.youtube.com/watch?v=oDYtZUNcYB8
Last edited by JacobGuy7805 (2014-09-01 17:24:25)

Trilby wrote:
pacman -Sc will not remove currently installed packages from the cache - so that likely did not do anything. You need to actually remove the package file, or use -Scc (and answer yes) to remove the cached file(s).
Then reinstall. It should show that it is being downloaded before installing.
You can also check whether this is actually the issue by comparing the output of the following two commands to the output I'm getting (as long as you are on x86_64):
$ ls -l /usr/lib/xorg/modules/drivers/nouveau_drv.so
-rwxr-xr-x 1 root root 203232 Jul 18 07:13 /usr/lib/xorg/modules/drivers/nouveau_drv.so
$ md5sum /usr/lib/xorg/modules/drivers/nouveau_drv.so
4eb8a6bd9ec92637a17ae70adaa9ef1f /usr/lib/xorg/modules/drivers/nouveau_drv.so
I had to pacman -Scc and then when I did "pacman -S {,lib32-}nouveau-dri xf86-video-nouveau" it said that a whole bunch of files existed in the filesystem (although when I did pacman -R and the packages it kept insisting I did not download those packages) so I ended up just removing the files manually with rm. I then installed the packages and things seem fine now. I'm going to reboot.
EDIT: IT WORKED! I had to generate a new Xorg.conf, and then I just changed some things, and it worked!
Last edited by JacobGuy7805 (2014-09-01 17:24:05)

Multiple 30" Cinema Displays, cable length too short

I have two 23" Cinema Displays, and they work great! Power adapters have long clean leads and can put them away from my G5 and place the displays where I want. Then I bought a 30" Cinema Display to try in prep for a "Nehalem" machine. I discovered that the power adapter has to be 6 inches away from the back of the computer and the monitor cable is SHORT. I want to use two 30" displays, but the cables are too SHORT and I don't want those two white bricks (power adapters) behind a new Nehalem. Apple says you can run up to eight 30" displays, with the necessary video cards, but no mention how to reach the second display let alone the 8th display!! Does Apple have cables in a male-female configuration? I have looked at Gefen.com and their extensions are Male-Male for the Apple Combo Extension Cables for dual link (30"). I could say demeaning things right now, but I won't.

Thank you for the quick reply, I can place the power adapter where I want with your solution. You would have posted if you knew about an extension with an "elegant breakout for connection to DVI, USB and FireWire ports" but I will still ask if you know of that kind also so that all monitors have USB and FireWire.

Apple Mini DVI to DVI Adapter - Too short?

I want to connect my iMac 2.8 ghz, 24" screen to an external Philips 190B LCD monitor and use the Extended Desktop function.
The Philips Monitor model is the 190B6CG/00 and it is a single link monitor (Philips tell me it is DVI-D Receptacle Connector 24 pin = single link).
I'm looking at the Apple Mini DVI to DVI adapter here on the Apple Store. It looks like it should plug into my iMac one end then the other end into my Philips. However it looks like it is too short to reach my Philips Monitor. They are not a fantastic distance apart. In fact they are sat side by side - but I somehow can't see the Apple Adapter being long enough (unless it crosses a 3-sphere).
Presumably then, some sort of extension is required between the DVI end of the Apple adapter and the Philips Monitor's DVI input.
Does anyone know what this extension could be and where is may be purchased?
Regards

Hello to everyone who has replied to my cry for help.
Thank you all. I will apply points to everyone who has responded (so quickly too).
Scorpie
I totally agree. I have been thinking along these lines too. However, searching on the internet whilst researching, I found it difficult to decide what I needed because of the 'photos' supplied. They were ok as such but most didn't show very well the pin outs. Further research into the matter (and one website in particular - i.e. Maplin) made me realise that GENDER was involved. Also, with DVI, females look like males in web photos until you find a photo from the right angle. Same goes for VGA I reckon.
I'm certain most people looking at DVI (and VGA) cable/connectors can't tell the difference when the devices are only viewed from 'above' . In my opinion they need to be viewed more or less end-on to show where they have pins or holes. I mean full end-on, not at an angle where (as I found above) detail as to pin or hole is lost in digital or compression noise. This is what I have experienced in all but one of the web sites I have visited. Another thing, most websites have an 'enlarged version' button which, if selected, shows the same photo exactly the same size. No help whatsoever. But then there's no doubt you must already be well aware of this.
MyHighway
You are correct. The Philips did come with a VGA cable. However I want to connect to my iMac digitally (if I can) using DVI (it looks like a 'female' connector on inspection of the back of the Monitor). I have found it almost impossible to tell the difference from most photos on the web even with my new huge screen iMac. One of the reasons I'm am a little nonplussed I think.
mrtotes
Good point. If I take a photo of the back of my Philips and take the Apple connector down to Maplin perhaps I can compare and contrast with real specimens. Yo!!
I think I will give that a go.
You have all been very helpful indeed. Opened my eyes somewhat.
I wish a Merry Christmas to all my new Mac friends

DVI to VGA adapter. Too short?

Hello.
Please do not blame me for being ignorant, I recently had to do a project and in order to connect to the screen, I need to use a DVI to VGA adapter, which is provided when I bought my MBP.
But then, isnt it too short? How do I connect it then? Must I buy a extension? Do help me as my project is due next friday and I must present next friday. Thank you.

Allan Jones wrote:
The sequence would be:
Mac > Adaptor > VGA cable > Monitor or projector
Right - except when actually hooking them up, they should be connected in the reverse of that sequence; the projector should be on and seeking an input, the cable and adapter should be connected, and the final step is to connect the adapter to the MBP.

DVI to VGA adapter Isn't it too short

I bought a MB Pro and I wanted to use the DVI to VGA adapter but it's too short, is there a longer one or is this it?

Maybe http://www.microcenter.com/singleproduct_results.phtml?productid=0201448 if you need a male-to-female. In other words, that product should work if the port on the TV has pins sticking out. If it has holes that pins should be stuck into, then http://www.microcenter.com/singleproduct_results.phtml?productid=0201735 is a male-to-male. Make sure you double check the photos against your adapter and your TV before you buy. Also try your local electronics or computer store.
dapeter2: Thanks for your clarification.

MacBook Pro to TV, Video Output Too Dark

Hi,
I have an 2010 model 15" MacBook Pro i5.
I got this video converter for Christmas:
http://www.amazon.com/VideoSecu-VGA2TV-Computer-Presentation-Converter/dp/B000X3 FAJU/ref=sr14?ie=UTF8&qid=1295210644&sr=8-4
Using this in conjunction with an Apple Mini DisplayPort-to-VGA adapter and a standard RCA video cable, I am able to connect my MacBook to my TV so I can stream video from sites like Hulu.
My TV is a Sanyo flat screen CRT that's, probably, 6-7 years old (exact model probably isn't important).
I have no issues with the quality of the video output I'm getting (i.e. resolution, color). The issue I'm having is that the video is too dark. The video looks great on my MacBook screen, but the TV display is too dark. I have tried playing with the settings on the TV and on the converter (through which I can adjust brightness, contrast, saturation, hue, and sharpness) and I can't, for the life of me, get the output to my TV brightened up to an acceptable level.
I have tried to use the display calibration tool in the Mac's display preferences and that didn't seem to help (I'll admit that I don't think I'm doing it correctly).
Can anyone suggest some steps that I might try in order to improve my video output?
Thanks.

No Answer, but related problem...please see my original post: http://discussions.apple.com/thread.jspa?threadID=2773439&stqc=true

Videos are too dark to watch on Macbook pro?

Ever since I got my Macbook pro a year ago, videos are too dark to watch at any setting.

Hi Paul,
Sorry for the late answer. I live in Europe, so that's why I was asleep ;-)
Basically the command tells your computer to unhide everything on your Desktop, so if you don't have a Desktop, something is definitely wrong.
My guess is that there's something wrong with your account on that computer. You can check that by creating a new account in System Preferences (click on Accounts, click the lock in the bottom-left corner and then click the "+" button just above).
Then try mounting "some" media and see if it appears on the new user's Desktop. If not, I would highly recommend to reinstall Mac OS X.
HTH,
Jasper.

HT1920 I have got a Activation Lock on my iPhone and I need to get it activated. I don't know what Apple ID I was using with my iPhone. It shows as U***@h******.uk which is too short to be my email address. I have reset all my Apple ID passwords and none

I have got a Activation Lock on my iPhone and I need to get it activated. I don't know what Apple ID I was using with my iPhone. It shows as U***@h******.uk which is too short to be my email address. I have reset all my Apple ID passwords and none are activating my iPhone. I have also been into the apple store and they have tried to find out the Apple ID my iPhone was using but this was not successful. The serial number of my iPhone is: C32JN641DTWF

You are going to need to change the email address you use with your old ID. Once you have got access to your old account you will then log into both accounts at the same time on your Mac and transfer your data to a single account. We can do this later, but need you to get access to your old account first.
My Apple ID

Error "602" System error: AK Datapart too short

Hi all,
Ok, I have looked just about everywhere for an answer to this but to no avail...I even tried under a few rocks we have laying around.
Anyway here it is:
While running a compression in BW we get Error "602" System error: AK Datapart too short.
This is happening while doing a select statement during the compression of the infocube. It does not happen all the time, just kind like when ever it feels like. The only note I could find in OSS was one about Live Cache and it does not seem to apply.
Here is the dump which I really hate doing this, but it gives all the info needed :
untime Error          DBIF_DSQL2_SQL_ERROR
Except.                CX_SY_NATIVE_SQL_ERROR
Date and Time          08/15/2007 12:23:09
ShrtText
An SQL error occurred when executing Native SQL.
What happened?
Error "-602" occurred in the current database connection "DEFAULT".
What can you do?
Print out the error message (using the "Print" function)
and make a note of the actions and input that caused the
error.
To resolve the problem, contact your SAP system administrator.
You can use transaction ST22 (ABAP Dump Analysis) to view and administer
termination messages, especially those beyond their normal deletion
date.
is especially useful if you want to keep a particular message.
How to correct the error
Database error text........: "System error: AK Datapart too short"
Database error code .......: "-602"
Triggering SQL statement...: "INSERT INTO "/BIC/EZPSD_C03" ( "KEY_ZPSD_C03P",
"KEY_ZPSD_C03T", "KEY_ZPSD_C03U", "KEY_ZPSD_C031", "KEY_ZPSD_C032",
"KEY_ZPSD_C033", "KEY_ZPSD_C034", "/BIC/ZNET_ASP" ) SELECT ? ,
F."KEY_ZPSD_C03T", F."KEY_ZPSD_C03U", F."KEY_ZPSD_C031", F."KEY_ZPSD_C032","
Internal call code.........: "[DBDS/NEW DSQL]"
Please check the entries in the system log (Transaction SM21).
You may able to find an interim solution to the problem
in the SAP note system. If you have access to the note system yourself,
use the following search criteria:
"DBIF_DSQL2_SQL_ERROR" CX_SY_NATIVE_SQL_ERRORC
"GP31VIZWJDTT90894L1IA5YAC7G" or "GP31VIZWJDTT90894L1IA5YAC7G"
"TRANSFER_ALL"
If you cannot solve the problem yourself and you wish to send
an error message to SAP, include the following documents:
1. A printout of the problem description (short dump)
To obtain this, select in the current display "System->List->
Save->Local File (unconverted)".
2. A suitable printout of the system log
To obtain this, call the system log through transaction SM21.
Limit the time interval to 10 minutes before and 5 minutes
after the short dump. In the display, then select the function
"System->List->Save->Local File (unconverted)".
3. If the programs are your own programs or modified SAP programs,
supply the source code.
To do this, select the Editor function "Further Utilities->
Upload/Download->Download".
4. Details regarding the conditions under which the error occurred
or which actions and input led to the error.
The exception must either be prevented, caught within the procedure
"TRANSFER_ALL"
"(FORM)", or declared in the procedure's RAISING clause.
To prevent the exception, note the following:
System environment
SAP Release.............. "640"
Application server....... "sdcbw03"
Network address.......... "10.64.18.76"
Operating system......... "Linux"
Release.................. "2.6.9-55.ELsmp"
Hardware type............ "x86_64"
Character length......... 16 Bits
Pointer length........... 64 Bits
Work process number...... 21
Short dump setting....... "full"
Database server.......... "sdcbw03"
Database type............ "ADABAS D"
Database name............ "BWP"
Database owner........... "SAPBWP"
Character set............ "C"
SAP kernel............... "640"
Created on............... "Nov 5 2006 19:46:34"
Created in............... "Linux GNU SLES-9 x86_64 cc3.3.3"
Database version......... "SAPDB 7.5.0.030 "
Patch level.............. "156"
Patch text............... " "
Supported environment....
Database................. "MaxDB 7.5.0"
SAP database version..... "640"
Operating system......... "Linux 2.6"
Memory usage.............
Roll..................... 16192
EM....................... 20949280
Heap..................... 0
Page..................... 24576
MM Used.................. 9235016
MM Free.................. 3331560
SAP Release.............. "640"
User and Transaction
Client.............. 011
User................ "ALEREMOTE"
Language key........ "E"
Transaction......... " "
Program............. "GP31VIZWJDTT90894L1IA5YAC7G"
Screen.............. "SAPMSSY0 1000"
Screen line......... 6
Information on where terminated
The termination occurred in the ABAP program "GP31VIZWJDTT90894L1IA5YAC7G" in
"TRANSFER_ALL".
The main program was "RSPROCESS ".
The termination occurred in line 573 of the source code of the (Include)
program "GP31VIZWJDTT90894L1IA5YAC7G"
of the source code of program "GP31VIZWJDTT90894L1IA5YAC7G" (when calling the
editor 5730).
The program "GP31VIZWJDTT90894L1IA5YAC7G" was started as a background job.
Job name........ "BI_PROCESS_COMPRESS"
Job initiator... "ALEREMOTE"
Job number...... 12185102
Processing was terminated because the exception "CX_SY_NATIVE_SQL_ERROR"
occurred in the
procedure "TRANSFER_ALL" "(FORM)" but was not handled locally, not declared in
the
RAISING clause of the procedure.
The procedure is in the program "GP31VIZWJDTT90894L1IA5YAC7G ". Its source code
starts in line 557
of the (Include) program "GP31VIZWJDTT90894L1IA5YAC7G ".
Source Code Extract
Line
SourceCde
543
ENDIF.
544
545
COMMIT WORK.   " commit and close cursors
546
547
l_str = i_max_requid.
548
PERFORM msg_append(saplrscondense)
549
USING    'S' '355' l_str space space space
550
CHANGING c_t_msg.
551
552
ENDFORM.                               " CONDENSE_FACTTABLE_NEW
553
554
555
     Form TRANSFER_ALL
556
557
FORM TRANSFER_ALL USING i_ref_update       TYPE rs_bool
558
i_pdimid           TYPE I
559
i_pdimid_ref_point TYPE rsd_sid
560
i_pdimid_normal    TYPE rsd_sid
561
i_recordtp         TYPE rsd_sid
562
CHANGING e_ref_ins_cnt TYPE I
563
e_ins_cnt     TYPE I
564
c_t_msg       TYPE rs_t_msg.
565
566
CALL FUNCTION 'RSDU_INFOCUBE_INDEXES_DROP'
567
EXPORTING
568
I_INFOCUBE = 'ZPSD_C03'
569
I_FACTTAB = '/BIC/EZPSD_C03'.
570
571
572
EXEC SQL.
>>>>>
INSERT INTO "/BIC/EZPSD_C03"
574
( "KEY_ZPSD_C03P"
575
, "KEY_ZPSD_C03T"
576
, "KEY_ZPSD_C03U"
577
, "KEY_ZPSD_C031"
578
, "KEY_ZPSD_C032"
579
, "KEY_ZPSD_C033"
580
, "KEY_ZPSD_C034"
581
, "/BIC/ZNET_ASP"
582
583
SELECT :i_pdimid_normal
584
, F."KEY_ZPSD_C03T"
585
, F."KEY_ZPSD_C03U"
586
, F."KEY_ZPSD_C031"
587
, F."KEY_ZPSD_C032"
588
, F."KEY_ZPSD_C033"
589
, F."KEY_ZPSD_C034"
590
, SUM( F."/BIC/ZNET_ASP" )
591
FROM "/BIC/FZPSD_C03" F
592
WHERE F."KEY_ZPSD_C03P" = :i_pdimid
Any thoughts would be helpful,
Thanks,
David

This error usually occurs when there is a database lock or no space in teh database. Got DB02 and Click on Space critical objects to see whether any entries are there. If yes contact your basis to increase the space.
Hope this helps
Thanks,
Satish

Postal code is too short or invalid when trying to sign up for windows azure

https://account.windowsazure.com/signup?offer=ms-azr-0044p
language is Netherlands
country is Belgium
postal code is "8870" but is considered too short
I also tried "BE8870" or "BE-8870" but these are considered invalid
how do I continue?

HI
May be you can try "8870 Emelgem".
If still can't help Please contactsupport team by creating a support ticket at
http://www.windowsazure.com/en-us/support/contact/
Or if that doesn't work because you don't have an active subscription you will need to contact general customer support to have them create a support ticket for you
http://support.microsoft.com/gp/customer-service-phone-numbers?wa=wsignin1.0
Dino He
MSDN Community Support | Feedback to us
Develop and promote your apps in Windows Store
Please remember to mark the replies as answers if they help and unmark them if they provide no help.

Video playlife too short

Similar Messages

Maybe you are looking for