Video through HDMI, audio through headphones

Because of the way my sound system/TV is set up, I can't stream sound from the TV to the sound system; the sound system is picky about its input. I'd like to be able to use the HDMI to connect the video from my iPhone to the TV, but use the standard audio jack to connect to the sound system's Audio In. Is it possible to split the audio and video to different outputs?

first of all, make sure you connect the cable before you switching on the device and connec it well.
secondly, try to update drivers and bios.

Similar Messages

Captured video only plays audio through one speaker

I captured video from a mini dv and when I play the clip in FCP the audio only plays out of one speaker and it only shows on one audio meter in FCP. I captured this video with a DSR-20 and it displayed NS Audio on the screen. Both meters were playing on the deck and in FCP while previewing and also through my headphones. Does anyone know what I need to do this to correct this?

First I'd verify how the audio was captured. Did you have it set for Ch 1 + Ch 2, or Stereo, or Ch 1 [only], or Ch 2 [only] or as a mono mix?
Next, verify that you actually had two channels of audio on the tape, not just one channel.
Assuming that there are two channels on the tape, load the captured clip into the Viewer and see if there is an audio waveform on both channels. If there is, check to see if both channels are panned the same - if they are, pan one left and one right or both to center.
If there were no waveforms on one of the channels, try capturing a short segment of the same tape using another Firewire cable.
-DH

HDMI audio through TV "mix" issues

Hi All,
I've got my ATV2 connected vai HDMI to my Phillips LCD TV, it seems there is a phasing problem or something....I listen to music I am familiar with and the vocals seem mixed very low, and I know it's not right. Most likely the issue is with the TV, but I have adjusted as many settings as I could find, and there seems to be no fix. In fact, if I turn off the "Super Surround" audio mode, I get some really terrible sounding phase cancellation/comb filtering sounds. Just wondering if anyone has heard anything like this.
Thanks!

If you connect the MacBook using a Mini DisplayPort to HDMI adapter you will probably need to use external speakers or a 3.5mm stereo headphone jack to RCA sound plugs connected to a stereo sound system if your TV doesn't have separate RCA input plugs or a 3.5mm stereo input plug for audio with the HDMI plug. The Mini DisplayPort to HDMI doesn't carry audio unless you have the Mid 2010 model 7,1 and there're no audio plugs on most TVs to work with HDMI since it's expecting audio with the HDMI.
If you have the Late 2008 model 5,1 Aluminum Unibody or Late 2009 model 6,1 White Unibody with the Mini DisplayPort rather than the Mini-DVI there is an adapter that uses the Mini DisplayPort and a USB port to combine video and audio to HDMI. It's only 2 channel stereo not 5.1 Dolby Surround.
http://www.monoprice.com/products/product.asp?c_id=104&cp_id=10428&cs_id=1042802 &p_id=5969&seq=1&format=2
To see which model you have go to the Apple in the upper left corner and select About This Mac, then click on More Info (and then System Report if you’re running 10.7 Lion). When System Profiler comes up check the Model Identifier and post it back here.

HDMI Audio through Mini Displayport?

Hi all
I've just ordered a mini-display port/HDMI adapter that supports audio which I assume would work on my 13"MBP. However I have just been looking at a few pages on the net that put me in some doubt. My MBP was purchased mid May 2010 and I was told in the Apple store at the time that it was the latest model, just in, as the line up was revised April 2010? But there appears to be a lot of confused surround it and if it supports audio via the mini-display port.
Can anyone confirm the functionality on this model?
Model Name: MacBook Pro
Model Identifier: MacBookPro7,1
Processor Name: Intel Core 2 Duo
Processor Speed: 2.4 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache: 3 MB
Memory: 4 GB
Bus Speed: 1.07 GHz
Boot ROM Version: MBP71.0039.B0B
SMC Version (system): 1.62f5
Serial Number (system):
Hardware UUID: 6C518889-5B72-53DE-ADF9-22E85CFC96D0
Sudden Motion Sensor:
State: Enabled
Many Thanks
Matt.
Message was edited by: mattcastledine

Yes, the MBP 7,1 supports audio via mini-Displayport, so assuming your adapter also supports audio as advertised, it should do what you bought it for.

HT204291 Airplay video but no audio through Safari

I have a problem with Airplay not allowing audio from Safari based media. I am trying to steam an NFL game but the audio will not transfer from built in speakers to Airplay. I have noticed this is an issue on the discussion boards and have done all they suggest. Help!

Hi,
Many vendors, if not all have not released drivers for Windows 8 officially therefore we have to wait. The following forum may help:
http://www.forumswindows8.com/
Good luck.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Trouble running DVI video and HDMI audio out of 6950

Twin frozr iii 6950 2gb (X2 crossfire)
Asus VG236 Monitor
Windows 7
MSI P67A-G43 Motherboard
Yamaha RX-V371 Receiver
I have two Twin Frozr iii 2gb 6950 cards and am attempting to use the HDMI on the video card solely for 5.1 audio out to my receiver while using video through the DVI jack of the same card directly to my monitor without success.
-Audio functions if I run the HDMI from the card into my receiver, then out to my Asus VG236 monitor.
-Audio functions when I run from the card to my receiver then out to my plasma tv.
-Audio functions if I have the DVI run directly to the Asus VG236 monitor and HDMI to the receiver then plasma tv (only in dual display and the tv must be on for audio to function this way. If I turn the tv off even though the receiver is still on the audio stops working and windows sound lists the 'AMD HDMI Output' as not plugged in).
-Audio even fuctions when I run DVI to the monitor and HDMI to the receiver, then out to the HDMI port on the same monitor but the monitor will only run at 60hz this way even when DVI is selected on the monitor, as though it defaults to the HDMI when dvi and hdmi are both plugged into the monitor.
And if i run the hdmi to the receiver "HDMI IN" port without using the "HDMI OUT" port from the receiver to anything, like my tv or monitor, the sound doesn't work and in windows sound the "AMD HDMI Output" is listed as "not plugged in" .
I purchased this monitor for the true 120hz capabilities, the HDMI on this monitor doesn't support 120hz, the maximum is 60hz. DVI is required to run at 120hz. I don't see any option in windows sound settings or CCC to resolve this.
I have also tried disabling onboard audio in BIOS with no effect.
For now i'm running the audio out my MOBO jack through an optical cable to the receiver but optical only supports 2.1 sound.
Any suggestions you can offer would be appreciated, thank you

bump,
Anybody?

How do you setup HDMI audio with "Nvidia Quadro 4000 for Mac"?

So I just purchased a new Mac Pro:
Mac Pro (5,1) 3.33 GHz 6-Core
8 GB Ram
ATI Radeon HD 5770
1TB HDD
OS 10.8.3
I also purchased a new Nvidia Quadro 4000 for Mac Graphics Card because the 3D animation software I'm using (Blender) requires this card to accelerate render times.
I have installed the card and all is working well as far as I can tell except for the HDMI audio. According to the specs on Nvidia for this card, it DOES support HDMI audio through the Display port. I have my HDMI cable plugged up and the video works great. However the audio option does not show up in the System Preferences. (Here is the page for the graphics card. Look under "specifications" at the bottom for the audio part. http://www.nvidia.com/object/product-quadro-4000-mac-us.html).
I did find a link for a kernel addition for HDMI audio but it stated "non-Apple Nvidia cards" and this one is specifically for Mac. Here is that link: http://forums.macrumors.com/showthread.php?t=1499797. (I also plan on posing the same question there.)
The reason I want the HDMI to work is I'm using a TV as my monitor.
Now I did try the HDMI with the ATI Card and both the audio and video work great.
What I did for a quick work around is install both cards and use the GPU processor on the Nvidia for the animation program and use the ATI for the actual port and this fixes the hdmi audio issue. However this takes up pretty much all of my PCI slots and seems like a waste of space and power.
Has anyone else run into this problem and found a solution?? Any guidance would be greatly appreciated.
Thanks!

I went ahead and tried that extension that I found. It worked!
I guess Mac just didn't include the audio support in the driver that it includes. Below is were I found the instructions and download. It includes a shell script that installs the kernal from the Terminal prompt. The instructions were clear and installed with out a hitch. There were also instructions to remove it if there were issues.
Here is the link:
http://forums.macrumors.com/showthread.php?t=1499797
Thanks again and hope this helps.

[Solved] HDMI audio broken after upgrading to kernel 3.13.4

Hi,
Yesterday I upgraded to kernel 3.13.4 from 3.12.9 and
HDMI audio through my nVidia GTX660 card stopped working.
The problem occurs both with nouveau and nVidia drivers.
My system is an aged Intel quadcore Q9400 on a Intel motherboard.
By typing "aplay -l" I get:
card 0: Intel [HDA Intel], device 0: 92HD73E1X5 Analog [92HD73E1X5 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: Intel [HDA Intel], device 1: 92HD73E1X5 Digital [92HD73E1X5 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: NVidia [HDA NVidia], device 7: HDMI 1 [HDMI 1]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: NVidia [HDA NVidia], device 8: HDMI 2 [HDMI 2]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: NVidia [HDA NVidia], device 9: HDMI 3 [HDMI 3]
Subdevices: 1/1
Subdevice #0: subdevice #0
Strangely the alsa card number changed from 1 to 2
after the kernel upgrade.
I would really appreciate any help.
Thanks
Last edited by tenoriocalc (2014-02-23 16:02:46)

Thank you very much, silenceleaf.
I managed to make it work with some tweaking like you said.
But only after a deep power cycle, unpluging any power to the system.
Just turning off the machine's power button was not enough. Odd!
Last edited by tenoriocalc (2014-02-23 16:09:44)

Is there a way to play video through HDMI and have the audio via the headphone socket?

I would like to be able to play movies through the HDMI adapter to a projector, but to have the audio via the headphone socket to a separate audio system. What I find is that as soon as I connect the projector via HDMI, the audio via the headphone sockeet is cut off. Any ideas?

Yes, there is a very simple way to get audio out through the iPad headphone jack even while connected to HDMI to play movies on a projector or TV. In fact, I just did it last night for a presentation.
With the HDMI adapter connected to the projector and your audio jack plugged into your iPad headphone jack, go ahead and start the movie. Then simply unplug the headphone jack and plug it back in. The audio is now routed through the headphone jack again.
I found I only had to do this once per session. That is, Iwas able to stop the movie, go to the beginning of my presentation, wait the 20 minutes for the meeting to begin, and when I got to the video clip the audio still played out through the headphone jack to the PA system.
I had built a presentation in a Web oriented training tool and it was running on Safari iOS7 with the latest update. I have not tried it with Keynote yet.
iPad mini (original version)

How can i use audio through hdmi on mac book pro i have video no audio version10.6.8

how can i use audio through hdmi on mac book pro i have video no audio version 10.6.8 in audio it just has internal speaker options

Hello,
Open Audio Midi Setup in Applications>Utilities, see the input & output options & KHz setting there.

Can you airplay video from iPhone to Apple TV but listen to the audio through iPhone headphones?

I know this is a very specific use, but my wife sleeps during the day while I'm at home. To keep the house quiet, is it possible to airplay a video on my iphone to the Apple TV, but listen to the audio through my headphones plugged into the iPhone?

No, you would need to connect the headphones to the audtio out on the TV or strero being used.

No audio / video through hdmi from vista home premium

dear friends
am using dv6000 with vista home premium
trying to connect tv output through hdmi but unable to show show either audio or video
with the same cable, i tried in diff laptop and it works fine
pls advise me
i have my windows and all drivers updated

When you run Lenovo driver installer downloads, the drivers are not installed. This is normal (!). The drivers are unpacked into a directory on your disk, usually under C:\DRIVERS. You have to follow the installation instructions (on the same page you downloaded from). Usually they say go to the directory where the drivers were unpacked and run setup.exe, but not always, so you have to pay attention if you choose to install the drivers this way.
The simplest way out of your situation is to manually install the Ethernet drivers, plug into the Internet, then download and install ThinkVantage System Update, and run it. It should churn away and automatically install all the right stuff.
Whether you choose to install the ThinkVantage stuff manually or automatically using System Update is up to you.
BTW it sounds like you MAY have blown away the Lenovo Rescue & Recovery partition when doing your "upgrade". If you did, and you want to get that back, you will need to call Lenovo for a recovery DVD, and start from scratch.
Message Edited by bananaman on 02-28-2009 10:20 AM
I don't work for Lenovo. I'm a crazy volunteer!

Trying to record Stereo Mix with a monitor through my headphones. Using Screenium to record Audio and Video, using Avid MBox Mini with MXL 909 Microphone for the audio through the interface.

Basically, what I am trying to do is this:
Record my screen through Screeenium, record my voice as audio through an Avid MBox Mini (interface) with a MXL 909 microphone to pick up the audio. I have all that figured out. I'm able to efficiently record my audio and screenplay through these instruments and programs. What I am having trouble with is the stereo mix. I am running into a slew of problems here... My goal: Add on the audio of a game that I am playing (for example, Amneisia) so that the audio for my game will be picked up internally, and not through the speakers to be recorded through the microphone. I want there to be no external sound except me talking into my microphone. I also want to be able to HEAR the audio of the game through my headphones (and if possible, myself as well, through a monitor maybe?)
Problems I have run into so far:
-Haven't gotten it to pick up in game audio at all while using headphone. Can't figure this out
-Downloaded soundflower, have the output as soundflower. Not picking up anything, will put all my sound and midi settings at the end.
-When I do record through my microphone, it is only picking up a single channel (left earpiece only, no right channel)
-I have figured out it is NOT the equipment, I use Pro Tools and am able to pick up both channels with my mic, recorded a few tests. It's settings and I can't figure it out
-Trying not to run 16 million programs while running the game, will cause lag.
Summed up:
Trying to record:
-Audio from gameplay of any game I am playing through alternative route of speakers (do NOT want to record game audio through speakers, internally)
-Record voice through Avid MBox Mini and MXL 909 microphone.
-Record screen gameplay through Screenium
I followed a guide that told me to achieve "stereo mix'' I need to download soundflower and follow "X" steps. That is done and these are my current settings:
Audio Midi Setup - Stereo Mix custom Aggregate Device, Soundflower (2ch) selected, Avid Mbox Mini selected, Soundflower Output #1 has 2 channels (1-2), using Avid MBox mini for "Input" in order to record. Using Soundflower AND Avid MBox mini as "Output" in order to hear the sounds and replay game sounds (could be the problem? Maybe?)
Sound Settings - Output Stereo Mix (custom channel) Input Avid MBox Mini (recording)
I'm hoping this isn't too hard to understand.. I'm VERY bad at explaining information regarding computers.. It's hard becuase I don't understand it. I can clarify anything that I am able to, so any help on finding certain things would be greatly appreciated.
My computer: Macbook Pro MAC OS X Lion (11G63) 10.7.5 2.4 GHz Intel Core i7 4GB 13333 MGz DDR3 (If any of this is imporant)

Hey guys,
I tried to do some research and it looks like you need to have an external device and its drivers, such as an external microphone, installed on the computer to record audio that can be saved as a sound file. Another Suggestion is to try an auxiliary spliter for your headphones and external speakers?
What software are you using to record your game?
If anyone knows anything different, please let me know.
Thank you for being a part of the Lenovo Family,
Catie
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Donate KUDOS and Click "Accepted Solution"

How to make my computer send all the audio through optical audio cable instead of headphone jack?

Howdy,
To listen to online radios or CD's played from my computer, I used to connect the computer to my home entertainment system from the computer's headphone jack to the AUX port on my home entertainment system.
I now wanted to get better sound and purchased the optical audio cable. However, I don't know how to tell my computer to send the audio signal to the home entertainmeny system through the optical digital cable rather than through the headphone jack. If I just unplug the cable connecting the headphone jack and the AUX port and only have the PC and the system connected with the optical audio cable, I don't hear any sounds. I suspect the computer isn't sending any data through the optical audio port. I'm not able to find how I can adjust the settings on my computer so that from now all sounds are output through the optical audio.
1) I'd like to do that mainly for my HP desktop (configuration below) and any advice on how to do that would be appreciated.
2) I also have a HP laptop (configuration below) and was wondering if that would be doable too (even though it doesn't appear to have a audio out, but it has HDMI out - can one convert it to optical audio?
Thanks in advance!
My desktop is:
ENVY h8xt,
• Windows 8 64
• 3rd Generation Intel(R) Core(TM) i7-3770 quad-core processor [3.4GHz, 8MB Shared Cache]
• 12GB DDR3-1333MHz SDRAM [3 DIMMs]
• 1TB 7200 rpm SATA hard drive
• No secondary hard drive
• 1GB AMD Radeon HD 7570 [DVI, HDMI, DP, VGA adapter]
• 300W Power supply
• SuperMulti DVD Burner
• Wireless-N LAN card (1x1)
• 15-in-1 memory card reader, 2 USB 2.0 (front), 2 USB 3.0 (top)
• No Additional Office Software
• No additional Security Software
• No TV Tuner
• Beats Audio (tm) -- integrated studio quality sound
• HP USB volume control keyboard and mouse with Win 8 keyboard
• Adobe Premiere Elements & Photoshop Elements 10
And the laptop:
HP ENVY 15t Quad
• Windows 8.1 64
• 4th generation Intel(R) Core(TM) i7-4700MQ Processor
• NVIDIA(R) GeForce(R) GT 740M Graphics with 2048MB of dedicated video memory
• 15.6-inch diagonal Full HD BrightView LED-backlit Display (1920x1080)
• 8GB DDR3 System Memory (1 Dimm)
• 1TB 5400 rpm Hard Drive
• 24GB flash Hard Drive Acceleration Cache
• No Additional Office Software
• Security Software Trial
• 6-Cell Lithium-Ion Battery
• No Internal DVD or CD Drive
• Standard Keyboard
• HP TrueVision HD Webcam w/ integrated digital mic
• 802.11 AC WLAN and Bluetooth(R) [2x2]
This question was solved.
View Solution.

Hello @_goma,
Welcome to the HP Forums, I hope you enjoy your experience!
I have read your post on how you are looking to make your computer send all the audio through an optical audio cable instead of the headphone jack, and I would be happy to assist you in this matter!
To configure your desktop to enable the optical audio cable, I recommend following the steps below:
Step 1. Click the Windows Key Button on your desktop
Step 2. Type "Control Panel"
Step 3. Select "Control Panel" in the top right-hand corner
Step 4. Select Sound
Step 5. Under the Playback tab, right-click the white area below the devices available
Step 6. Select "Show Disabled" and "Show Disconnected Devices"
Step 7. Connect your Optical Audio Cable
Step 8. Select your Optical Audio Cable as the default device and click "Enable"
Since it is not possible to convert the HDMI out to audio out on your notebook computer, it is unfortunate that the notebook is not able to connect with an optical audio cord.
Please re-post with the results of your troubleshooting, and I look forward to your reply!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

HP HDX Laptop - Solution for no audio through HDMI

Hi Guys,
Just want to share, how i resolved the HDMI Audio issue. I have a HP HDX16t laptop with latest Vista 32bit nvidia drivers (GeForce 9600MGT - 186.03 June 9, 2009) and last week i tried to connect it with my new Philips 32" LCD TV. I was disappointed to only see the video and couldn't hear audio through my TV. I tried to change the default playback device as SPDIF, but no luck as the 'NVidia HDMI Output' was always showing as disconnected. Somewhere in the internet i read that HDMI sound was working fine untill they updated nvidia drivers!! I tried to rollback my nvidia drivers and it restored the previous release 185.85 May'09 which didn't work. So I searched nvidia website to find the archived drivers and found 179.29, Dec'08 release to work flawlessly. Now everytime I connect the HDMI cable, Nvidia HDMI output is selected automatically and when i unplug it, built-in speakers and headphones are selected.
http://www.nvidia.com/object/geforce_notebook_winvista_179.28_beta.html
I need to check if I can have the latest video drivers in combination with the audio drivers from 179.29 release.
Sorry for my bad english...just trying to save your time

Hello
The issue is because 185 and 186 version recognize HDMI connector like DVI conector ¿?., something is wrong with this actual versions.
Nvidia just tell me the following: "The issue you are experiencing is not a general behavior of the graphics card or the graphics driver.I will forward this issue to the concerned department to analyze the issue and if we're able to reproduce this issue then, will definitely try coming up with a fix in the future driver."
Go to complain about this issue to Nvidia Support in order to let them know that I´m not the only person on this world having this issueBy the way, their time response is less than 2 hours, go for it.To find this NVidia Support, just follow these instructions:
Go to visit "Nvidia webpage" // go to "Support" // go to "Knowledgebase" // then find "Ask a Question". Login will be requested, you´ll need to fill a very short form.
Message Edited by Dantew on 06-29-2009 02:56 PM

Video through HDMI, audio through headphones

Similar Messages

Maybe you are looking for