VideoConference MCU

In the web page of the MCU, I try to Create a Conference, I select the prefix (default 81 type Video) and I enter the unique number and when I do click in the boton "create" this message is showed: Error: No Resource are available. And the EMP module is registered in the MCU the conference with meet-me and ad-hoc conference works withou problem ... Why happen this ?

81 is for h323 by default.
and probably you use all video ports for SCCP, go to MCU>Protocol>SCCP and check how many ports are assigned for sccp.

Similar Messages

Videoconfrence : Help with MCU to configure in CCM

Hi,
I have a confusion with the configuration of the MCU in CallManager when i want to have a multipoint videoconference where 3 SCCP viedo endpoints(7985) and 1 Polycom video endpoint (H.323) participate all in the same confenrence!
Here is attached the architecture of my videoconference deseign.
I have activated SCCP and H.323 on the MCU.
I have added the MCU as a conference bridge in CCM, and configured MRGL to use this Conference Bridge.i associated the MRGL with the 3 video SCCP endpoint(7985) and now i can do Multipoint videoconference between the three video endpoints (7985)!!
The problem that i want to the Polycom participate and to initiate a videoconference with the other SCCP endpoints.
I have added a gatekeeper, i registered the MCU (H.323 activated) with the gatekeeper!! In CCM i added the gatekeeper and added a trunk Gatekeeper controlled!!
Now here is my problem: what else to do in CCM??
Should i create a route pattern that points to the trunk ??
or should i add the MCU as a H.323 gateway and a route pattern that points to the this H.323 gateway???
PLz help me, i really have a serious problem.
Thx

Hi,
i think that the most difficult part is done now.
plz can u tell me first of all if the bridge is registered with the callmanager?in the administration page of the CCM, click SERVICE >> MEDIA RESOURCE >> CONFERENCE BRIDGE.
Then u have to find your bridge configured (u should see it's IP address).
If this is done, so u need to configure a service (SCCP activated)in the MCU.
U need to login to ur mcu with a browser, then click SERVICES >> ADD , and u need to activate the SCCP field, then choose ur video and audio parameters.
If this is done so to start a videoconference(between 3 persons for example) all u have to do is :
If u have 3 persons : A,B and C (and u'r the person A)
so A calls B normally, here a point to point videocall should be established (done by the CCM), then to make multipoint videoconference, u shoud click on the button MORE of ur phone, u'll see the word CONF, click CONF, u enter the number of the third person and when he hangs on the phone u click an other once on CONF. then a Multipoint videoconference should be established using the bridge this once.
unfortunately i can't have picture of my configuration because i did it in a production in another entreprise but u the online course (ICRMC) an e-learning course, had helped me a lot an there is flash videos that can give u an idea:
http://www.cisco.com/web/learning/le36/learning_partner_e-learning_connection_tool_launch.html
i hope this helps,
If there is an other problem plz contact me.

Help with MCU 3515 in SCCP with CCM 6.1

Hi,
I have CCM6.1 + MCU3515 configured for skinny only.
I want to have a multipoint videoconference between 3 SCCP video endpoints (7970+VTA).
If I try to make an adhoc conference, I only have audio, no video.
If I try to initiate the conference from the MCU, everything works fine.
12 videos ports are allocated to the SCCP protocol profile.
MCU version is 5.5
Any idea on what could be the problem ?
Thanx,
Bastien.

Yes, it was simply a problem of regions and locations.
My locations wasn't well configured (no enough bandwith defined).

Videoconference

Hi I have a MCU 3545 integrate with the Cisco Call Manager version 6, the MCU is the main conference bridge in the CCM. The video endpoints are 7985, CUVA and VSX Polycom 7000, the videoconference work Fine. I connect a Polycom View Station in the videoconference but only audio is available and only hear the audio and automatically disconnected after a minute.
What is the problem?

Did you enable dynamic bandwidth setting on the VSX? It may be occasionally causing the endpoint to down speed to a level below the tolerance limit for the MCU to maintain an open video channel and calls were connecting audio only.

Multipoint videoconference problem

We have in our company(ISP) a videoconference network that consists of 35 videoconference points connected to a central point consisting of a Cisco 7200 gatekeeper, a Cisco IP/VC 3540 videoconference system with a MCU MC06A. The equipment from these 35 points are 23 ViaVideo II systems, 10 PictureTel 550 video systems and 2 PictureTel 600 Series video systems(from 2 main points). Ok. What is the problem? A videoconference session is taking place with all these 35 points connected(without problems). Surposing site number 2(a ViaVideo) is talking with one main site(a PictureTel 600) but suddenly a crashing noise appears(for less than 1 second) and video switchs to another site, for example site number 24. We see that site number 24 doesn't have his microphone connected. After some minutes it happens again and video switchs to another site(only video - audio is muted at that site). Something it's going wrong. All sites have good connection between them.
Any idea what's the matter? Or where I can found exact information about this?

! No configuration change since last restart
version 12.2
no service pad
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec
service password-encryption
hostname Video-GK
logging queue-limit 100
enable secret xxxxxxxxxxxxxxxxxxxxxxxxxxx
username admin privilege 15 password xxxxxxxxxxxxxxx
clock timezone EET 2
clock summer-time EET recurring last Sun Mar 2:00 last Sun Oct 3:00
clock calendar-valid
ip subnet-zero
ip cef
no ip domain lookup
ip domain name xxxxxxxxx.xx
ip name-server x.x.x.x
ip name-server x.x.x.x
no ip bootp server
no voice hpi capture buffer
no voice hpi capture destination
mta receive maximum-recipients 0
proxy h323
interface FastEthernet0/0
description -= Local Switch 2690G Link =-
ip address x.x.x.x 255.255.255.240
ip route-cache same-interface
load-interval 30
duplex full
speed 100
no cdp enable
h323 interface
h323 qos ip-precedence 4
h323 h323-id Video-GK-proxy
h323 gatekeeper id Video-GK ipaddr x.x.x.x
h323 t120 bypass
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
no cdp enable
ip classless
ip route 0.0.0.0 0.0.0.0 x.x.x.x
no ip http server
no cdp run
call rsvp-sync
mgcp profile default
dial-peer cor custom
gatekeeper
zone local Video-GK MTC_Video x.x.x.x
lrq forward-queries
no use-proxy Video-GK default inbound-to terminal
use-proxy Video-GK default inbound-to gateway
use-proxy Video-GK default inbound-to mcu
no use-proxy Video-GK default outbound-from terminal
use-proxy Video-GK default outbound-from gateway
use-proxy Video-GK default outbound-from mcu
no shutdown
banner incoming ^C +++ Welcome to Cisco 7200 Video Gatekeeper +++ ^C
banner login ^C +++ Welcome to Cisco 7200 Video Gatekeeper +++ ^C
line con 0
stopbits 1
line aux 0
stopbits 1
line vty 0 4
exec-timeout 0 0
login local
ntp clock-period 17180162
ntp peer x.x.x.x
end

Welcome Message MCU

I have the Cisco IPVC-3545 version 5.5, and when I start a videoconference I see and hear a welcome message which is in English. I can change the language of this message ?

you can create a "Welcome to the conference, you are the first participant" message in your language and upload it as the initial MCU prompt.
The download you need is on CCO (software downloads/IPVC)
IPVC-MCU-Voice-Prompts.zip

Does MCU 3515 supports direct ip dialling?

Hi,
Does anyone knows if MCU 3515 supports direct ip dialling? we want to establish videoconferences but participants should be able to dial to an IP address without registering to a gatekeeper.

Direct IP dialing is supported on MCU 3515 only in version 5.6. In order to do so, you have to do the following :
- Put a fake gatekeeper address (if you don't have any gatekeeper) i.e. 1.1.1.1 (do not use an ip address ending with 0).
- Enable Auto Attendant IVR
- Choose a Default Service Prefix previously configured as Service Type : "HD/SD Continuous Presence".
- Disable "Register conference ID" on Advanced Settings.
Now you can Dial through the MCU IP address.

Cisco 3545 MCU/EMP

Hello all,
I'm deploying a videoconference solution with a Cisco 3545 with one MCU and one EMP. I've done the basic configurations. The MCU has the ip 10.10.0.170 and the EMP with the 10.10.0.171, mask 255.255.255.240. The problem is that the EMP card never appears in the Media Processing tab in the MCU of the MCU admin page, and on the EMP console keeps popping up the message "NO MCU detected at this IP address: 10.10.0.170".
Do you have any idea?
Best regards.

I was just troubleshooting a video issue recently, and although our problems were different, I learned a few troubleshooting tools.
1. Go on your MCU and see if you can schedule Video meetings directly on the MCU, just to see if that piece works.
2. If that is working, go on your Video Admin web interface and go under Admin/Resource Management...click the MCU tab and then click on the link to the MCU. There is an Update button down there. Click the Update button, then try again.
What I have discovered is if that at any point your restart your MCU and don't click that Update button after, the Video Admin will get out of sync with the MCU and not be able to schedule Video.
So that is something to try to start with.

Jabber Client through Collab Edge dials MCU - no Video

Hi There,
I think this is a licensing issue, but would need clarification as to what is required.
We have Jabber Clients externally connecting through Collab Edge, Jabber to Jabber video works great, but when conferencing the client gets only Audio. (this is expected).
We have implemented a software MCU via a SIP trunk from the CUCM which works fine internally, but when Jabber clients dial this through Collab Edge, no video is received or sent.
My understanding is some "Rich Media" license is required on VCSe or VCSc? Can someone explain what is required or another way to accomplish multiparty video using external jabber clients?
Thanks

Rich media sessions licenses are only required if you need to video call people outside of your organization, that is the registration of the remote user's endpoint doesnt register to the CUCM that is integrated with MRA.
Are you using device mobility by any chance and have you set certain locations for users who come in through MRA? Does this location have enough bandwidth for video?

Logic Pro X inaccessible after waking from sleep when using an MCU Control Surface

I'm having a problem I cannot seem to get around without force quitting Logic every time. If I have a Control Surface setup as a Mackie Control (v1.0); and if the computer goes to sleep, and then i turn off the controller while the computer is asleep (for any reason), and then wake the computer without turning on the controller first, Logic becomes completely unusable and must be force quit.
My controller in this example is Solid State Logic's Nucleus controller, however it happens with other Mackie Control compatible controllers (i have another one i tested against), BUT not a real Mackie Controller sold by Mackie (i tested with that as well); more details below.
For the SSL controller, Logic automatically sets it up like this:
Now if the computer goes to sleep, and i wake it up, i get the following dialog, which is fine:
After clicking on "Continue" button or hitting the enter key, Logic is rendered useless, as if there is a modal dialog still open somewhere. Clicking anywhere on the gui results in white flashes and nothing else. doing cmd+Q to quit actually makes it try to quit (a save dialog appears), but it never does successfully quit, making me resort to force-quitting. For an example, here's a pic of the file menu at this point:
I also have a regular Mackie Control Unit (MCU Pro) and the strange thing is with that unit, everything works fine after sleep, turning off controller, and re-awakening. However, there is a difference in what kind of dialog is displayed after the sleep, which probably has something to do with this issue.
Here is the setup screen of the MCU Pro:
And here is the dialog for the missing ports after waking from sleep:
This dialog is completely different than the other control surface's missing ports dialog. When clicking on "Keep unassigned" here, Logic resumes working fine.
The project is as minimal as possible; nothing is loaded, all that's there is an empty instrument track and a Control Surface configured.
I'm using a Mac Mini (late 2012)
Processor 2,6 GHz Intel Core i7
Memory 16 GB 1600 MHz DDR3
Graphics Intel HD Graphics 4000
Software OS X 10.9.4 (13E28)
with Logic Pro X 10.0.7
Any help would be greatly appreciated!!

Did you ever figure out a solution to this problem?
I just pulled out my original Emagic Logic Control (MIDI) and I have having the same problem.

How to create a video only conference at MCU 5320 .. ?

How to create a video only conference at MCU 5320 .. ?

Hi,
This community is for Cisco Webex Meetings Server and Cisco Unified MeetingPlace products. For questions about Telepresence MCU, I would advise you post this question under Telepresence community to get a TP expert answer it.
I hope this helps.
-Dejan

H.323 videoconference client

Hi,
i´ve been searching some standard videoconference client H.323
to install in my director´s company notebook and i cannot find any software to communicate with our videoconference system Policom.
I need a client like Netmeeting, that can manage this types of protocols.
Somebody knows about this kind of software?
Thank you in advance.
J.

Hi Swordfish --
Check out the info here: http://www.ncsu.edu/it/multimedia/netmeeting/netmeeting.html - near the bottom of the linked page. See if that helps.
This thread also seems potentially helpful: http://capmac.org/phpbb2/viewtopic.php?t=2349&
Both threads mention ohphonex, though they indicate it doesn't have all of netmeeting's capabilities: http://www.versiontracker.com/dyn/moreinfo/macosx/18544
-- JDee

Connection problems between logic Pro X and Mackie MCU PRO

Hello, I need help.
I bought a mackie MCU control PRO and don´t work on my Logic Pro x. Does anyone know if I have to do something in the logic to configure? or should it automatically go?
Thanks for your help
This is my equipment list if you have any questions;
MAc Book Pro, Maverik IOX
Motu Ultralite
Mackie MCU PRO
Logic Pro X

Not enough information to help you.

Mac to Pc bonjour videoconference

hi you all, i don't know if this can be done but, does anyone know how to videoconference between a Mac and a Pc with bonjour? meaning no internet, just the local network.
Thanks

Possible but not checked.
Trillian Pro still says Rendezvous
I believe the Trial is of the Pro version for 7 days.
(Rendezvous is the old name in Panther for what is now Bonjour).
As iChat uses the same codec to Audio or Video chats in Bonjour as it does in any AIM or Jabber (iChat to iChat) contact you may get this to invoke the AIM Codecs in Trillian
10:03 PM Monday; December 8, 2008

IPVC-3511-MCU - Can't see all persions at the same time on conference

Hello,
I can't see all persion at the same time on conference. I also can't see seperate screen on LCD pannel or CVTA on PC.
Does IPVC-3511-MCU support multiple conference with multiple video screen?
Regards,
John.

Hi -
This feature is called continuous presence - there are a number of references on Cisco's web site for the 3511. Here is one - http://www.cisco.com/en/US/customer/products/hw/video/ps1870/products_administration_guide_chapter09186a00804fc993.html and possibly another - http://www.cisco.com/en/US/customer/products/hw/video/ps1870/products_data_sheet0900aecd801c5e66.html
You did not mention the release of the 3511 software you are running. Knowing that might help too.
Ginger

VideoConference MCU

Similar Messages

Maybe you are looking for