Viewing firewire external device and VGA monitor with mirroring off

My mac laptop is connected to an external monitor via the VGA port and I keep mirroring off to maximize display space. When using FCP I want to run firewire out to a professional DVcam deck for both capture, and to view the timeline on an external monitor that I see by using 'RCA monitor out' on the DVcam deck to the monitor. However, as soon as I turn mirroring off, the deck no longer sees the firewire. How can I see the firewire out and the VGA display monitor when mirroring is off. thanks

Is the ADVC powered? When you connect firewire to the back of the unit, it gets powered by that connector, but the firewire jack on the front is only 4-pin and doesn't support power.
If you have a 6-pin to 6-pin firewire cable, try connecting it to the back of the ADVC110 and then the front of the box should light up, indicating power.
I'm having a similar issue. I can print to tape via the Canopus box, but I want to be able to drive a monitor with it just so I can have an NTSC monitor while I'm editing. I can't seem to make it work. Any ideas?

Similar Messages

Using DVI and VGA monitor simultaneously on MacPro

using DVI and VGA monitor simultaneously on MacPro!
2008 MacPro - running the latest Yosemite
for the last few years, I've had two monitors attached - both DVI monitors in the DVI port.
today, one of the two monitors died on me! Just wouldn't turn on.
As it happens, I also have an older VGA monitor. So, this evening I bought a VGA-to-DVI adaptor.
when I plugged it in, something buggy happened ... the image was fine at the first, but then for a while, the active application started flashing off & on, it flashed between the image of the APP and a white panel... just the active APP. the background apps looked fine.
now it seems to have stopped .. .but I fear it may come back?
no idea what may be causing it! is it NOT a good idea to use DVI and VGA monitors simultaneously on a 2008 MacPro?
Hope it doesn't come back. right now I'm in safe start-up mode, I'll see what happens when I run normal start-up mode tom'w morning.
thanks for any feedback / insight!
will

this is all the info from ABOUT THIS MAC
I believe the video card is the original from 2008 - I don't think I've changed that since the machine was new :
ATI Radeon HD 2600 XT:
Chipset Model: ATI Radeon HD 2600
Type: GPU
Bus: PCIe
Slot: Slot-1
PCIe Lane Width: x16
VRAM (Total): 256 MB
Vendor: ATI (0x1002)
Device ID: 0x9588
Revision ID: 0x0000
ROM Revision: 113-B1480A-252
EFI Driver Version: 01.00.252
Displays:
SyncMaster:
Resolution: 1280 x 1024 @ 60 Hz
Pixel Depth: 32-Bit Color (ARGB8888)
Display Serial Number: HCJX844788
Main Display: Yes
Mirror: Off
Online: Yes
Rotation: Supported
LCD19D(TMDS):
Resolution: 1280 x 1024
Pixel Depth: 32-Bit Color (ARGB8888)
Display Serial Number: WCCE5100535
Mirror: Off
Online: Yes
Rotation: Supported
thanks again!
minor update: I went back to the DVI monitor, using another 12V AC cable, and it seemed to work, but then that one just started flickering (after being on for an hour or so...) the flickering stopped after a few minutes, but something tells me that I'm not out of the woods yet...
w

Is it possible to output to a projector and a monitor with Keynote?

Hi, I am looking to set up my Macbook Pro for a presentation, I have hooked up two extra output displays - a projector through the DVI for the main presentation and a monitor with an Iogear USB - VGA connector on stage for the speakers notes. The Macbook will be side stage. Is it possible in Keynote to display the main presentation on the projector and the speakers notes to the monitor? I have tried mirroring the laptop to the monitor but this has caused problems with it only working when the projector is designated the home screen (with the dock) meaning people will see what is going on through the projector. When the laptop is the home screen and keynote is started a message appears saying there's not enought virtual memory. Is there anyway around this?

This is not possible with a mini.

I have an iPhone and iPad. I would like to get my husband an iPhone. Are we able to sync all devices and share info with both iPhones and the iPad, using a single email address?

I have an iPhone and iPad. I would like to get my husband an iPhone. Are we able to sync all devices and share info with both iPhones and the iPad, using a single email address?

Thanks for that. He is one of the last holdouts in IT so an email address for him would just mean I have 2 to check so that is what I am trying to avoid as we move into retirement:)

How can I delete an Apple ID from one device and replace it with a different ID on that same device?

How can I delete an Apple ID from one device and replace it with a different ID on that same device?

Tthe brute force method: start with Settings > iCloud and turn off Find My (you will need the password), then change the iCloud ID, then go to the apps such as Messages, FaceTime, etc, and delete the Apple ID and enter the new one.

Can I back up an external drive and an airbook with a third drive

I would like to back up an external drive and an airbook with a third drive. This was the setup I used with my Imac. The third drive was linked to the external drive which was linked to the imac. I used time machine. Both the third drive and the external drive were visible on the desktop of the imac. Now I want to use this system to back up the airbook and the external drive, but the third drive doesn't appear on the airbook's desk top, in fact it is invisible and doesn't seem to be recognized in finder or anywhere else from the airbook. Is there some distinction that prevents the airbook from allowing this back up configuration, but that allowed the imac to work in this configuration.
Thanks,
Daviiiiiiid

Of course, always that the external drive is formatted in “Mac OS Extended (Journaled)”. Apart from that, you shouldn't have any issue,
Then, open System Preferences > Time Machine > Options, and remove the external drive from excluded items. The next backup will include your external drive.
Note that you may not be able to back up the external drive if it's connected to your Time Capsule. If it doesn't work, connect the external drive to your computer

I need to update my iTunes and iPod touch,iPad and iPhone but they were set up with a hp laptop that i sold i tried to update my iTunes and apple devices but it tell's me if i update i will lose all media on my devices and to update with the original com

I need to update my iTunes and iPod touch,iPad and iPhone but they were set up with a hp laptop that i sold i tried to update my iTunes and apple devices but it tell's me if i update i will lose all media on my devices and to update with the original computr

Go to www.ecamm.com and d/l PhoneView.
To prevent a sync when plugging in the iPod/iPhone - hold down the 'option' and the 'command' keys when plugging in the iPod/iPhone - key the keys down until the iPod/iPhone is listed under the Devices list in iTunes - this will prevent a sync from taking place.
With PhoneView you can take the content from the device to the iTunes library.
MJ

Sync mail on iOS devices and a PC with icloud

Is it possible to sync mail on iOS devices and a PC with icloud such that when a mail is deleted on one device it is deleted on all devices?

You should be able to use iCloud mail on your Mac, however you will have to enter the settings manually. Unfortunately you will not be able to use the other features of iCloud for which lion is required. (calendars, contacts etc)

Mixing VGA and DVI monitors with 5770

Hi everyone,
I've seen the Apple articles and the forum posts about this, but before I need to check my configuration will work before it has to be used on a show at work (the MP is running screens in a venue). I've seen lots of scenarios with people using all DVI monitors or all VGA, but can't find any examples where they are mixed.
Here is my proposed setup:
DVI output - 800 x 600 - First device (DVI input only)
Mini Display Port 1 - also 800 x 600 - Second device (DVI/VGA input but strongly prefer to use DVI) via Mini Display Port -> DVI adapter (passive?)
Mini Display Port 2 - 1376 x 7?? - Monitor running the UI (VGA input) via Mini Display Port -> VGA adapter (active?)
My worry is that there is only one active adapter in the system?
If this won't work, I have two backup plans, which I would also like to know if it will work or not, please. One of the DVI devices has a buffered DVI link out, so I could use that to feed the other DVI device.
So Backup plan 1:
DVI output - 800 x 600 - DVI in of first device
Mini Display Port 1 - 1376 x 7?? - Monitor running the UI (VGA input) via Mini Display Port -> VGA adapter (active?)
MDP 2 not used.
Backup plan 2:
DVI output - 800 x 600 - DVI in of first device
Mini Display Port 1 - also 800 x 600 - Second device, VGA input via Mini Display Port -> VGA adapter
Mini Display Port 2 - 1376 x 7?? - Monitor running the UI (VGA input) via Mini Display Port -> VGA adapter
Phew, sorry for the essay everyone. Been a long day of trying to research all of this...
Thanks in advance.

Obviously backup plan 1 is no problem with only two monitors connected.
You have a relatively easy set of conditions. Two of your monitors are single link DVI (resolutions less than 1920 x 1200). One is vga. So a mini-displayport (mDP) to VGA counts as one active adapter and all you need is a a mini-displayport to single linke DVI active adapter for one of the others.
If you look at AMD Eyefinity Validated Dongles chart you would find that a Accell B087B-006B qualifies as an mini-displayport to single link DVI active adapter.
So a possible setup would be:
DVI --> 800 x 600 DVI display #1
mDP --> B087B-006B --> 800 x 600 DVI display #2
mDP --> VGA adapter --> 1376 x 7?? display #3

Ultra 10 with Creator 3D and VGA monitor

On the back of my Ultra 10 there are two connectors for monitors: one is the usual VGA connector and appears to be connected to the motherboard, the other is the traditional 13W3 Sun connector, apparently located on a Creator 3D card that came with the system.
I have a Sun monitor, and I can use it with the Ultra 10 using the 13W3 connector; unfortunately, however, it is quite old and would like to connect the box to a newer monitor. So I tried to simply unplug the Sun monitor and plug in a VGA one, but nothing happened. Uhm, what am I forgetting to do?
Incidentally, another silly question: supposing I do manage to connect a VGA monitor, what device will generate the display? The Creator 3D (that does NOT have a VGA connector) or the onboard device, whatever that is (since the VGA socket is connected to the motherboard, apparently). This could be relevant for the speed of graphics rendering, I suppose.

This topic seems to re-appear every so often.
<img src="images/smiley_icons/icon_cool.gif" border=0 alt="Cool">
The UPA framebuffer will be more capable that the onboard ATI Rage chipset,
which only has 4mb of video RAM and you will not get 24bit color if you set its resolution higher than 1152x900.
You could also consider reconfiguring the system to run dual monitors.
Search these hardware forums, keyword "xservers" (plural)
I just saw about 35 hits.
Then when you're ready, review the complete contents of the following file (case sensitive):
<b>/usr/dt/config/Xservers</b>
Depending on how you customize that file, you choose which monitor is console and which is the 'other one' ; you decide which is the left output and which is the right-hand screen; you could even run the output in a monitor spanning single GUI mode, although with disparate monitor models and different framebuffer chipsets, that may not be pleasing to the eye.
( see the man page for Xinerama )
If I recall correctly, you can also find the user profile for a contributor named <u>ultraspec</u> and glance through a few of their postings, where they mention a DB13W3 to HD15 adapter cable.
Edit: Oh, until such time as you do invoke the Xservers file within Solaris, I think the onboard circuit is disabled so long as the Creator card is physically inside. Remove the Creator card and the onboard is spontaneously your graphics output.

Older iPod and Viewsonic Monitor with dock

Hello All,
I just bought the 22" Viewsonic LCD monitor with iPod dock on it. I have an older 40gig iPod. (almost 4 years old)
The doc sync's with my iPod and iTunes just fine, BUT it does not charge. I originally thought that it was an issue with the monitor, but after repacking and replacing it, I still have the issue on my new monitor.
Is there some kind of charging issue with the older iPods and this dock? Any thoughts would be appreciated.
Thank you,
v

I just purchased the 22" View Sonic and my 5th Gen Video iPod won't even sync with iTunes. In fact I get an error messagage from windows saying the devices is not working.

FireWire external drives and bootable DVD's

I have 2 Mac Pro running 10.5.2 with all recent updates:
1) Mac Pro *****UXYL model MacPro3,1 (early 2008)
2) Mac Pro *****00PX model MacPro1,1 ROM de démarrage : MP11.005D.B00
On the second I can mount and boot with a FireWire external drive. I can also use an utility DVD or CD like DiskWarrior.
On the first one, nothing of this is possible : I cannot mount a FireWire drive only an USB drive. I cannot use CD or DVD bootables except of course Install Disks (version 1.1)
I tried to obtain an answer from Apple support without any success.
<post edited by host>

The ROM has been reported in the past to be one element of the issue, but in general Apple has made it abundently clear that you can't install an older operating system on a Mac nor boot from an older operating system than the Mac than came with it in these two articles:
http://docs.info.apple.com/article.html?artnum=303315
http://docs.info.apple.com/article.html?artnum=25517
And as far as I know no one has been able to downgrade the ROM to an older version than it shipped with either to force boot an older operating system.

Agent Desktop Recording and Silent Monitoring with IP Communicator.

Reading through the forums I have seen several posts which make me think this should work, but I can't seem to get silent monitoring or recording using the agent desktop to work when the agent is connected through IP communicator. Currently I have help desk agents using extension mobility to log into 7962s that are connected to thier desktops running agent desktop connecting to UCCX 7.01. Silent monitoring and recording work fine with thier hard phones. When I install IP communicator on the PC and log into it using EM, the agent desktop takes control of the IPC just fine and will distribute calls to it, but my recordings are blank and silent monitoring from an supervisor station fails to initialize. Is there something I am missing in the configuration that is special when using IPC instead of a hard phone? Thanks in advance.

Couple of things I've learned about the CIPC and monitoring/recording:
No named devices. Use the SEP + Mac Address of the local Ethernet interface.
Ensure the Ethernet interface can be put into permiscuous mode.
Ensure you are NOT using a shared line appearance for the IPCC Extension.
If you are using CAD to do the monitoring/recording, launch the CIPC before you launch CAD
If you are using SPAN, ensure the CIPC RTP traffic will traverse the network where the SPAN interface is located.
If you are calling phone-to-phone, know that the CIPC will attempt to negoitiate G.722. UCCX cannot monitor/record G.722. Set the region or call to the PSTN where you can guarantee a G.711 or G.729 call.

Powermac g4 and VGA monitor

I am trying to get a VGA monitor to work with a Powermac G4 (digital audio). I am using a DVI to VGA adapter. I get it booted and get to the gray screen but them it goes to "Mode not supported". If it was a windows machine I would just go to "Safe Mode"(f8) and set up the monitor. How do I do it with this machine? The operating system is 10.?? and none of my old Mac monitors have the correct plugs for this machine.

Thanks I tried that and was able to get to safe mode. I still couldn't get a display. I dug out an old multi-sync monitor and was able to get it to work. The LCD monitor apparently didn't like the refresh rate. I'll see what it takes to get the LCD to work, I'm "off-the-grid" and can't afford to use all the juice the multi-sync monitor takes.
Thanks again

Can I connect dual vga monitors with the HP Pavilion p6724y

I'm looking at purchasing the HP Pavilion p6724y and currently have 2 vga monitors I'd like to use. Is this possiable?

Hi Stacey ,
Welcome to forum..
You need to get a video card with 2 VGA port .,, and install it on the computer to attach both monitor,,,
You can check local computer store for video card with 2 VGA port..
Click on the Kudos sign on left to say Thanks...

Viewing firewire external device and VGA monitor with mirroring off

Similar Messages

Maybe you are looking for