VIN 2 - Access failed. Unknown error...

Hi all,
I made the deployment of VIN 2.0. Apparently all is well. I entered the license and enabled the discovery. After the first moments when VIN shows the message "First Discovery pending ..." then I get out of all VMs, including the same VIN, the message "Access failed. Unknown error while retrieving data from Infrastructure Navigator".
Any suggestions? I tried to restart it several times.
Matrix

Hi Matrix,
There could be many reasons for this.
Please check for the following:
1. Does the VIN VA have access to the VC?
2. Is the above VC configured to use non standard ports for HTTP/HTTPS communication (not 80/443)?
3. Does the VIN VA have access to the ESX hosts that host those VMs?
Have you contacted your sales engineer / PSO regarding this issue?
Is there an SR open on this?
It will be very helpful to get a support package from the VA to analyze what happened, as this is a very general error.
Regards,
Boris

Similar Messages

The attempt to burn a disc failed, unknown error (261). Can't back up to CD

The attempt to burn a disc failed, unknown error (261). I get this message every time I try to back up my music from itunes on to a CD. It doesn't matter if I try to back up all music or only music purchased from itunes. So far I have not been able to back up anything. Can someone please help me!!!! I have tried everything on the support website from apple, and nothing has worked. I am beginning to get very frustrated.
Thanks

+I know my computer is up to date on firmware, because I just bought this laptop 4 months ago - it's a brand new Dell Inspiron 1721.+
Actually, in that case I definitely think you should check your firmware. I just had a look at the 32-bit Vista downloads page at Dell for your Inspiron 1721, and there's firmware updates listed there for four different drive models, all dated within the last four months.
Head to the following Dell page and enter your model information to get to your Downloads page:
Dell drivers and downloads

The attempt to burn a disc failed, unknown error (261) Can't back up on CD

The attempt to burn a disc failed, unknown error (261). I get this message every time I try to back up my music from itunes on to a CD. It doesn't matter if I try to back up all music or only music purchased from itunes. So far I have not been able to back up anything. Can someone please help me!!!! I have tried everything on the support website from apple, and nothing has worked. I am beginning to get very frustrated.
Thanks

+I know my computer is up to date on firmware, because I just bought this laptop 4 months ago - it's a brand new Dell Inspiron 1721.+
Actually, in that case I definitely think you should check your firmware. I just had a look at the 32-bit Vista downloads page at Dell for your Inspiron 1721, and there's firmware updates listed there for four different drive models, all dated within the last four months.
Head to the following Dell page and enter your model information to get to your Downloads page:
Dell drivers and downloads

TFTP 'configuration update' from 5508 WLC fails stating reason as '%Error: Config file transfer failed – Unknown error –refer to log'

Dear Experts,
I have two WLCs and other management devices as part of same subnet. I am able to upload ‘configs’ from all the devices on to my TFTP server. However when I am attempting to do the same from one of my WLC, it is failing consistently stating error message as:
‘%Error: Config file transfer failed – Unknown error –refer to log
Has anyone else too faced the same issue and how would we overcome this? Any specific debug that could help get more details on it?
Though the error message says, refer to log but still I don’t see anything that gets reflected in ‘Monitor logs’ which is related to ‘configuration file’ upload failure.
WLC code: 7.4.100.0
PFA as the error snippet.
Thanks and Regards,
Adnan

Hi Kaneswaran,
Just a soft reboot helped me solved the problem :). Still I am on 7.4 and facing no issues after this.
Apologies for coming too late to respond. Getting a down time window was not that easy and so was much delayed to try soft reload. I am still on 7.4 and facing no issue.
Glad that in your case it starting working all of a sudden. Could you please verify from 'show tech-support' to confirm if by chance your WLC had undergone any crash that could have caused the WLC to reload and thus accidently fixing the issue :)
Best Regards,
Muhammed Adnan

IPhone 5 firmware restore failed (unknown error 1)

hi everyone,
I updated my iPhone 5 from ISO 6.1.2 to 7.1.1 via iTunes by restoring and it was working fine but when 7.1.2 update came n I was trying to install via wifi, it failed a lot of times. so I connect my iphone to iTunes n tried by restore iphone, during this my phone was restated and it never showed up on iTunes so I disconnect iphone, since that time iphone is in recovey mode, now whenever I connects iphone to iTunes, a msg pop up on iTunes "iTunes detected an iphone in recovery mode. You must restore this iPhone before it can be used with iTunes." so I click on and then I click on restore and update. it goes for Extracting Software> Restoring iPhone software>verifying iPhone software>restoring iPhone firmware but never completes, a msg comes on iTunes iPhone restore failed. unknown error(1) I does the same like I m putting a link from someone for iphone 5s.
https://www.youtube.com/watch?v=vQq9P0xiSGk
if someone has a solution please share with me asap.
Thanks

Check for hardware issues
Related errors: 1, 3, 10, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1000, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
These errors mean that your device or computer may have a hardware issue that's preventing the update or restore from completing.
Check that your security software and settings aren't preventing your device from communicating with the Apple update server.
Then try to restore your iOS device two more times while connected with a cable, computer, and network you know are good.
Confirm that your security software and settings are allowing communication between your device and update servers.
If you still see the error message when you update or restore, contact Apple support.

Attempt to Burn Disc Failed Unknown Error (4450)

Attempt to Burn Disc Failed Unknown Error (4450) this is what i get whenever i try to burn a disc, help?

I've been having the exact same problem and it's really making me angery cause every CD I try and burn ends up with not even a full song on it and the computer ejects it with error4450 popping up on the screen any help would be greatly apreciated

Installation operation failed.Unknown error (code:...

I am trying to intall the latest version of Nokia Ovi Suite 2.2.1.23 And keep getting Installation operation failed.Unknown error (code: 1612).
Have tried:-
Nokia PC Suite Cleaner
Uninstall Ovi Suite, PC Connectivity solution and Nokia Connectivity cable drivers from Add/remove program Delete the files from...
C:\Documents and Settings\User\Application Data\Nokia\Ovi Suite C:\Documents and Settings\user\Local Settings\Application Data\Nokia C:\Documents and Settings\All Users\Application Data\OviInstallerCache Used MSI clean up utility Restart PC.
Any solutions please...
using :-
Nokia 5800 XpressMusic
V50.0.005
Windows 7 (32 bit)

These errors is coming up, becasue the windows installer is corrupted. Please reinstall windows installer from the link provided below.
http://support.microsoft.com/kb/2438651/en-us
This should defnitely work..
All the best and good luck.
Cheers
Show appreciation by clicking the kudos star :-), or gesture by typing thanks

System image utility fails "Unknown error has occurred"

Hi,
I can create disk images from 10.8.3 clients but when i'm putting them through system utility on the 10.8 server it fails after hours of running.
The log is set to debug and shows the image creates upto 83% then jumps to 100% and later shows unknown errors and failed to create image from restore souce.
I've created several disk images and saved them to different locations on the server as the source and final image.
Below i've put in the debug log. Someone please help!!
Workflow Started (2012-01-02 13:56:58 +0000)
OS X Server 10.8.3 (12D78), System Image Utility 10.8.3 (624)
Starting action: Define Image Source (1.4)
Finished running action: Define Image Source
Starting action: Create Image (1.7.2)
Starting image creation process...
Create NetRestore Image
Initiating NetRestore from installed volume.
progressPrefix="_progress"
++ progressPrefix=_progress
scriptsDebugKey="DEBUG"
++ scriptsDebugKey=DEBUG
imageIsUDIFKey="1"
++ imageIsUDIFKey=1
imageFormatKey="UDZO"
++ imageFormatKey=UDZO
mountPoint=""
++ mountPoint=
ownershipInfoKey="501:20"
++ ownershipInfoKey=501:20
blockCopyDeviceKey="0"
++ blockCopyDeviceKey=0
dmgTarget="NetInstall"
++ dmgTarget=NetInstall
potentialRecoveryDevice="disk3s3"
++ potentialRecoveryDevice=disk3s3
asrSource="ASRInstall.pkg"
++ asrSource=ASRInstall.pkg
destPath="/Volumes/Macintosh HD/Library/NetBoot/NetBootSP0/NetRestore of Macintosh 10-8_2.nbi"
++ destPath='/Volumes/Macintosh HD/Library/NetBoot/NetBootSP0/NetRestore of Macintosh 10-8_2.nbi'
skipReorderingKey="0"
++ skipReorderingKey=0
sourceVol="/Volumes/Macintosh HD 1"
++ sourceVol='/Volumes/Macintosh HD 1'
postInstallHelperKey="1"
++ postInstallHelperKey=1
. "${1}/createCommon.sh"
+ . /tmp/niutemp.YPRmigsL/createCommon.sh
# createCommon.sh
# Common functionality for the Image creation process.
# sourced in by the various SIU scripts
# Copyright © 2007-2012 Apple Inc. All rights reserved.
# Using dscl, create a user account
AddLocalUser()
# $1 volume whose local node database to modify
# $2 long name
# $3 short name
# $4 isAdminUser key
# $5 password data
# $6 password hint
# $7 user picture path
# $8 Language string
local databasePath="/Local/Default/Users/${3}"
local targetVol="${1}"
# Find a free UID between 501 and 599
for ((i=501; i<600; i++)); do
output=`/usr/bin/dscl -f "${targetVol}/var/db/dslocal/nodes/Default" localonly -search /Local/Default/Users UniqueID $i`
# If there is already an account dscl returns it, so we're looking for an empty return value.
if [ "$output" == "" ]; then
break
fi
done
# Create the user record
/usr/bin/dscl -f "${targetVol}/var/db/dslocal/nodes/Default" localonly -create $databasePath
if [ $? != 0 ]; then
echo "Failed to create '${databasePath}'."
return 1
fi
# Add long name
/usr/bin/dscl -f "${targetVol}/var/db/dslocal/nodes/Default" localonly -append $databasePath RealName "${2}"
if [ $? != 0 ]; then
echo "Failed to set the RealName."
return 1
fi
# Set up the users group information
/usr/bin/dscl -f "${targetVol}/var/db/dslocal/nodes/Default" localonly -append $databasePath PrimaryGroupID 20
if [ $? != 0 ]; then
echo "Failed to set the PrimaryGroupID."
return 1
fi
# Add some additional stuff if the user is an admin
if [ "${4}" == 1 ]; then
/usr/bin/dscl -f "${targetVol}/var/db/dslocal/nodes/Default" localonly -append "/Local/Default/Groups/admin" GroupMembership "${3}"
if [ $? != 0 ]; then
echo "Failed to add the user to the admin group."
return 1
fi
/usr/bin/dscl -f "${targetVol}/var/db/dslocal/nodes/Default" localonly -append "/Local/Default/Groups/_appserveradm" GroupMembership "${3}"
if [ $? != 0 ]; then
echo "Failed to add the user to the _appserveradm group."
return 1
fi
/usr/bin/dscl -f "${targetVol}/var/db/dslocal/nodes/Default" localonly -append "/Local/Default/Groups/_appserverusr" GroupMembership "${3}"
if [ $? != 0 ]; then
echo "Failed to add the user to the _appserverusr group."
return 1
fi
fi
# Add UniqueID
/usr/bin/dscl -f "${targetVol}/var/db/dslocal/nodes/Default" localonly -append $databasePath UniqueID ${i}
if [ $? != 0 ]; then
echo "Failed to set the UniqueID."
return 1
fi
# Add Home Directory entry
/usr/bin/dscl -f "${targetVol}/var/db/dslocal/nodes/Default" localonly -append $databasePath NFSHomeDirectory /Users/${3}
if [ $? != 0 ]; then
echo "Failed to set the NFSHomeDirectory."
fi
if [ "${6}" != "" ]; then
/usr/bin/dscl -f "${targetVol}/var/db/dslocal/nodes/Default" localonly -append $databasePath AuthenticationHint "${6}"
if [ $? != 0 ]; then
echo "Failed to set the AuthenticationHint."
return 1
fi
fi
/usr/bin/dscl -f "${targetVol}/var/db/dslocal/nodes/Default" localonly -append $databasePath picture "${7}"
if [ $? != 0 ]; then
echo "Failed to set the picture."
return 1
fi
/usr/bin/dscl -f "${targetVol}/var/db/dslocal/nodes/Default" localonly -passwd $databasePath "${5}"
if [ $? != 0 ]; then
echo "Failed to set the passwd."
return 1
fi
# Add shell
/usr/bin/dscl -f "${targetVol}/var/db/dslocal/nodes/Default" localonly -append $databasePath UserShell "/bin/bash"
if [ $? != 0 ]; then
echo "Failed to set the UserShell."
return 1
fi
# Create Home directory
if [ -e "/System/Library/User Template/${8}.lproj/" ]; then
/usr/bin/ditto "/System/Library/User Template/${8}.lproj/" "${targetVol}/Users/${3}"
else
/usr/bin/ditto "/System/Library/User Template/English.lproj/" "${targetVol}/Users/${3}"
fi
if [ $? != 0 ]; then
echo "Failed to copy the User Template."
return 1
fi
/usr/sbin/chown -R $i:$i "${targetVol}/Users/${3}"
if [ $? != 0 ]; then
echo "Failed to set ownership on the User folder."
return 1
fi
# Copies a list of files (full paths contained in the file at $1) from source to the path specified in $2
CopyEntriesFromFileToPath()
local theFile="$1"
local theDest="$2"
local opt=""
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
opt="-v"
fi
while read FILE
do
if [ -e "${FILE}" ]; then
local leafName=`basename "${FILE}"`
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Copying ${FILE}."
fi
/usr/bin/ditto $opt "${FILE}" "${theDest}/${leafName}" || return 1
fi
done < "${theFile}"
return 0
# Copies a list of packages (full path, destination pairs contained in the file at $1) from source to .../System/Installation/Packages/
CopyPackagesWithDestinationsFromFile()
local theFile="$1"
local opt=""
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
opt="-v"
fi
while read FILE
do
if [ -e "${FILE}" ]; then
local leafName=`basename "${FILE}"`
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Copying ${FILE}."
fi
read SUB_PATH
/usr/bin/ditto $opt "${FILE}" "${mountPoint}/Packages/${SUB_PATH}${leafName}" || return 1
fi
done < "${theFile}"
return 0
# Create an installer package in ${1} wrapping the supplied script ${2}
CreateInstallPackageForScript()
local tempDir="$1"
local scriptPath="$2"
local scriptName=`basename "${scriptPath}"`
local entryDir=`pwd`
local opt=""
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Create installer for script ${scriptName}"
opt="-v"
fi
# shouldn't exist on entry...
if [ -e "${tempDir}/emptyDir" ]; then
/bin/rm -rf "${tempDir}/emptyDir"
fi
# make some directories to work in
/bin/mkdir $opt -p "${tempDir}/${scriptName}.pkg/Contents/Resources" || return 1
/bin/mkdir $opt "${tempDir}/emptyDir" || return 1
# Create Archive.pax.gz
cd "${tempDir}/emptyDir"
/bin/pax -w -x cpio -f "${tempDir}/${scriptName}.pkg/Contents/Archive.pax" .
/usr/bin/gzip "${tempDir}/${scriptName}.pkg/Contents/Archive.pax"
cd "${entryDir}"
# Create the Archive.bom file
/usr/bin/mkbom "${tempDir}/emptyDir/" "${tempDir}/${scriptName}.pkg/Contents/Archive.bom" || return 1
# Create the Info.plist
/bin/cat > "${tempDir}/${scriptName}.pkg/Contents/Info.plist" << END
<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
<plist version="1.0">
<dict>
<key>CFBundleIdentifier</key>
<string>com.apple.SystemImageUtility.${scriptName}</string>
<key>CFBundleShortVersionString</key>
<string>1</string>
<key>IFMajorVersion</key>
<integer>1</integer>
<key>IFMinorVersion</key>
<integer>0</integer>
<key>IFPkgFlagDefaultLocation</key>
<string>/tmp</string>
<key>IFPkgFlagInstallFat</key>
<false/>
<key>IFPkgFlagIsRequired</key>
<false/>
<key>IFPkgFormatVersion</key>
<real>0.10000000149011612</real>
</dict>
</plist>
END
echo "pkmkrpkg1" > "${tempDir}/${scriptName}.pkg/Contents/PkgInfo"
echo "major: 1\nminor: 0" > "${tempDir}/${scriptName}.pkg/Contents/Resources/package_version"
# Copy the script
/bin/cp "$scriptPath" "${tempDir}/${scriptName}.pkg/Contents/Resources/postflight"
# clean up
/bin/rm -r "${tempDir}/emptyDir"
return 0
# Validate or create the requested directory
CreateOrValidatePath()
local targetDir="$1"
if [ ! -d "${targetDir}" ]; then
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Creating working path at ${targetDir}"
fi
/bin/mkdir -p "${targetDir}" || return 1
fi
# If any exist, apply any user accounts
CreateUserAccounts()
# $1 volume whose local node database to modify
local count="${#userFullName[*]}"
local targetVol="${1}"
if [ $count -gt 0 ]; then
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Adding $count user account(s) to the image"
fi
for ((index=0; index<$count; index++)); do
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Adding user ${userFullName[$index]}"
fi
#lay down user here
AddLocalUser "${targetVol}" "${userFullName[$index]}" "${userUnixName[$index]}" "${userIsAdmin[$index]}" "${userPassword[$index]}" "${userPassHint[$index]}" "${userImagePath[$index]}" "${userLanguage[$index]}"
if [ $? != 0 ]; then
echo "Failed to create the User '${userUnixName[$index]}'."
return 1
fi
#suppress the Apple ID request
DisableAppleIDRequestForUser "${targetVol}" "${userUnixName[$index]}"
done
# "touch"
/usr/bin/touch "${targetVol}/private/var/db/.AppleSetupDone"
/usr/bin/touch "${targetVol}/Library/Receipts/.SetupRegComplete"
fi
# retry the hdiutil detach until we either time out or it succeeds
retry_hdiutil_detach()
local mount_point="${1}"
local tries=0
local forceAt=0
local limit=24
local opt=""
forceAt=$(($limit - 1))
while [ $tries -lt $limit ]; do
tries=$(( tries + 1 ))
/bin/sleep 5
echo "Attempting to detach the disk image again..."
/usr/bin/hdiutil detach "${mount_point}" $opt
if [ $? -ne 0 ]; then
# Dump a list of any still open files on the mountPoint
if [ "${scriptsDebugKey}" == "DEBUG" ]; then
/usr/sbin/lsof +fg "${mount_point}"
fi
if [ $tries -eq $forceAt ]; then
echo "Failed to detach disk image at '${mount_point}' normally, adding -force."
opt="-force"
fi
if [ $tries -eq $limit ]; then
echo "Failed to detach disk image at '${mount_point}'."
exit 1
fi
else
tries=$limit
fi
done
# Create the dyld shared cache files
DetachAndRemoveMount()
local theMount="${1}"
local mountLoc=`mount | grep "${theMount}"`
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Detaching disk image"
# Dump a list of any still open files on the mountPoint
if [ "${scriptsDebugKey}" == "DEBUG" ]; then
/usr/sbin/lsof +fg "${theMount}"
fi
fi
# Finally detach the mount (if it's actually mounted) and dispose the mountPoint directory
if [ "${mountLoc}" != "" ]; then
/usr/bin/hdiutil detach "${theMount}" || retry_hdiutil_detach "${theMount}" || return 1
fi
/bin/rmdir "${theMount}" || return 1
return 0
# Turn off the Apple ID request that happens on first boot after installing the OS
DisableAppleIDRequestForUser()
local targetUserLib="${1}/Users/${2}/Library"
# Only do this if the file doesn't exist
if [ ! -e "${targetUserLib}/Preferences/com.apple.SetupAssistant.plist" ]; then
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Disabling Apple ID request for user '${2}'"
fi
/usr/libexec/PlistBuddy -c "Add :DidSeeCloudSetup bool 1" "${targetUserLib}/Preferences/com.apple.SetupAssistant.plist" > /dev/null 2>&1
/usr/libexec/PlistBuddy -c "Add :LastSeenCloudProductVersion string 10.8" "${targetUserLib}/Preferences/com.apple.SetupAssistant.plist" > /dev/null 2>&1
fi
return 0
# If the pieces exist, enable remote access for the shell image
EnableRemoteAccess()
local srcVol="${1}"
local opt=""
if [ -e "${srcVol}/usr/lib/pam/pam_serialnumber.so.2" ]; then
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Enabling shell image remote access support"
opt="-v"
fi
# install some things (again which aren't part of BaseSystem) needed for remote ASR installs
/usr/bin/ditto $opt "${srcVol}/usr/lib/pam/pam_serialnumber.so.2" "${mountPoint}/usr/lib/pam/pam_serialnumber.so.2" || return 1
if [ -e "${srcVol}/usr/sbin/installer" ]; then
/usr/bin/ditto $opt "${srcVol}/usr/sbin/installer" "${mountPoint}/usr/sbin/installer" || return 1
fi
# copy the sshd config and add our keys to the end of it
if [ -e "${srcVol}/etc/sshd_config" ]; then
/bin/cat "${srcVol}/etc/sshd_config" - > "${mountPoint}/etc/sshd_config" << END
HostKey /private/var/tmp/ssh_host_key
HostKey /private/var/tmp/ssh_host_rsa_key
HostKey /private/var/tmp/ssh_host_dsa_key
END
fi
fi
return 0
# If it exists, install the sharing names and/or directory binding support to the install image
HandleNetBootClientHelper()
local tempDir="${1}"
local targetVol="${2}"
local opt=""
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
opt="-v"
fi
if [ -e "${tempDir}/bindingNames.plist" ]; then
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Installing Directory Service binding information"
fi
/usr/bin/ditto $opt "${tempDir}/bindingNames.plist" "${targetVol}/etc/bindingNames.plist" || return 1
/usr/sbin/chown root:wheel "${targetVol}/etc/bindingNames.plist"
/bin/chmod 644 "${targetVol}/etc/bindingNames.plist"
fi
if [ -e "${tempDir}/sharingNames.plist" ]; then
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Installing Sharing Names support"
fi
/usr/bin/ditto $opt "${tempDir}/sharingNames.plist" "${targetVol}/etc/sharingNames.plist" || return 1
/usr/sbin/chown root:wheel "${targetVol}/etc/sharingNames.plist"
/bin/chmod 644 "${targetVol}/etc/sharingNames.plist"
fi
if [ -e "${tempDir}/NetBootClientHelper" ]; then
/usr/bin/ditto $opt "${tempDir}/NetBootClientHelper" "${targetVol}/usr/sbin/NetBootClientHelper" || return 1
/usr/sbin/chown root:wheel "${targetVol}/usr/sbin/NetBootClientHelper"
/bin/chmod 555 "${targetVol}/usr/sbin/NetBootClientHelper"
/usr/bin/ditto $opt "${tempDir}/com.apple.NetBootClientHelper.plist" "${targetVol}/System/Library/LaunchDaemons/com.apple.NetBootClientHelper.plist" || return 1
/usr/sbin/chown root:wheel "${targetVol}/System/Library/LaunchDaemons/com.apple.NetBootClientHelper.plist"
/bin/chmod 644 "${targetVol}/System/Library/LaunchDaemons/com.apple.NetBootClientHelper.plist"
# finally, make sure it isn't disabled...
/usr/libexec/PlistBuddy -c "Delete :com.apple.NetBootClientHelper" "${targetVol}/var/db/launchd.db/com.apple.launchd/overrides.plist" > /dev/null 2>&1
fi
return 0
# If any exist, install configuration profiles to the install image
InstallConfigurationProfiles()
local tempDir="${1}"
local targetVol="${2}"
local profilesDir="${targetVol}/var/db/ConfigurationProfiles"
if [ -e "${tempDir}/configProfiles.txt" ]; then
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Installing Configuration Profiles"
fi
/bin/mkdir -p "${profilesDir}/Setup" || return 1
# Make sure the perms are correct
/usr/sbin/chown root:wheel "${profilesDir}"
/bin/chmod 755 "${profilesDir}"
/usr/sbin/chown root:wheel "${profilesDir}/Setup"
/bin/chmod 755 "${profilesDir}/Setup"
/usr/bin/touch "${profilesDir}/.profilesAreInstalled"
CopyEntriesFromFileToPath "${tempDir}/configProfiles.txt" "${profilesDir}/Setup" || return 1
# Enable MCX debugging
if [ 1 == 1 ]; then
if [ -e "${targetVol}/Library/Preferences/com.apple.MCXDebug.plist" ]; then
/usr/libexec/PlistBuddy -c "Delete :debugOutput" "${targetVol}/Library/Preferences/com.apple.MCXDebug.plist" > /dev/null 2>&1
/usr/libexec/PlistBuddy -c "Delete :collateLogs" "${targetVol}/Library/Preferences/com.apple.MCXDebug.plist" > /dev/null 2>&1
fi
/usr/libexec/PlistBuddy -c "Add :debugOutput string -2" "${targetVol}/Library/Preferences/com.apple.MCXDebug.plist" > /dev/null 2>&1
/usr/libexec/PlistBuddy -c "Add :collateLogs string 1" "${targetVol}/Library/Preferences/com.apple.MCXDebug.plist" > /dev/null 2>&1
fi
fi
# Converts a list of scripts (full paths contained in the file at $1) into packages in $3
InstallScriptsFromFile()
local tempDir="${1}"
local theFile="${2}"
local targetDir="${3}"
local opt=""
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Converting scripts into install packages"
opt="-v"
fi
while read FILE
do
if [ -e "${FILE}" ]; then
# make an installer package out of the script
CreateInstallPackageForScript "$tempDir" "${FILE}" || return 1
# copy the resulting package to the Packages directory
local leafName=`basename "${FILE}"`
/usr/bin/ditto $opt "${tempDir}/${leafName}.pkg" "${targetDir}/${leafName}.pkg" || return 1
# clean up
/bin/rm -r "${tempDir}/${leafName}.pkg"
fi
done < "${theFile}"
return 0
# Prepare the source by deleting stuff we don't want to copy if sourcing a volume
PostFlightDestination()
local tempDir="${1}"
local destDir="${2}"
local opt=""
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Performing post install cleanup"
opt="-v"
fi
# delete the DS indices to force reindexing...
if [ -e "${mountPoint}/var/db/dslocal/indices/Default/index" ]; then
/bin/rm $opt "${mountPoint}/var/db/dslocal/indices/Default/index"
fi
# detach the disk and remove the mount folder
DetachAndRemoveMount "${mountPoint}"
if [ $? != 0 ]; then
echo "Failed to detach and clean up the mount at '${mountPoint}'."
return 1
fi
echo "Correcting permissions. ${ownershipInfoKey} $destDir"
/usr/sbin/chown -R "${ownershipInfoKey}" "$destDir"
# Prepare the source by deleting stuff we don't want to copy if sourcing a volume
PreCleanSource()
local srcVol="$1"
local opt=""
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
opt="-v"
fi
if [ -e "$srcVol/private/var/vm/swapfile*" ]; then
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Removing swapfiles on $1"
fi
/bin/rm $opt "$srcVol/private/var/vm/swapfile*"
fi
if [ -e "$srcVol/private/var/vm/sleepimage" ]; then
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Removing sleepimage on $1"
fi
/bin/rm $opt "$srcVol/private/var/vm/sleepimage"
fi
if [ -d "$srcVol/private/tmp" ]; then
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Cleaning out /private/tmp on $1"
fi
/bin/rm -r $opt "$srcVol/private/tmp/*" > /dev/null 2>&1
fi
if [ -d "$srcVol/private/var/tmp" ]; then
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Cleaning out /private/var/tmp on $1"
fi
/bin/rm -r $opt "$srcVol/private/var/tmp/*" > /dev/null 2>&1
fi
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Cleaning out devices and volumes on $1"
fi
if [ -d "$srcVol/Volumes" ]; then
/bin/rm -r $opt "$srcVol/Volumes/*" > /dev/null 2>&1
fi
if [ -d "$srcVol/dev" ]; then
/bin/rm $opt "$srcVol/dev/*" > /dev/null 2>&1
fi
if [ -d "$srcVol/private/var/run" ]; then
/bin/rm -r $opt "$srcVol/private/var/run/*" > /dev/null 2>&1
fi
# Copy kernel and build the kext cache on the boot image
PrepareKernelAndKextCache()
local srcDir="$1"
local destDir="$2"
local opt=""
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Preparing the kernel and kext cache for the boot image"
opt="-v"
fi
# Insure the kext cache on our source volume (the boot shell) is up to date
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Updating kext cache on source volume"
fi
/usr/sbin/kextcache -update-volume "${srcDir}" || return 1
# Copy the i386 and, if it exists, the x86_64 architecture
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Installing the kext cache to the boot image"
fi
# make sure this doesn't exist
if [ -e "${destDir}/i386" ]; then
/bin/rm -rf "${destDir}/i386"
fi
# Install kextcaches to the nbi folder
if [ "${scriptsDebugKey}" == "VERBOSE" -o "${scriptsDebugKey}" == "DEBUG" ]; then
echo "Creating a kernelcache for the boot shell"
fi
/bin/mkdir -p $opt "${destDir}/i386/x86_64" || return 1
/usr/sbin/kextcache -arch x86_64 -L -N -S -z -K "${srcDir}/mach_kernel" -c "${destDir}/i386/x86_64/kernelcache" "${srcDir}/System/Library/Extensions" || return 1

I am seeing a very similar output trying to make a netrestore image of a 10.8.4 Macbook Air on a 10.8.4 Mac Mini running OSX Server. Gets to 84% and then shows the -1 progress and then just hangs until I cancel it (I haven't tried leaving it over night but left it that way for hours).
Did you ever figure out what was going on or have a workaround to create an image?
Thanks!

Attempt to burn a disc failed - unknown error 4260

I see there are lots of topics about not being able to burn CDs in iTunes but I can't find one with the exact same error message as mine - 4260. I've not had any problems before (I haven't tried to burn a CD for some months), but today I tried to burn a CD with purchased tracks from iTunes Store, and it seemed to have burned okay. Then when I played it in the car, the first 3 tracks were fine and then the rest were jumpy and had an awful background noise. Came home and found it wouldn't play properly in the computer (froze iTunes at track 4) or on my CD player. Tried again to burn to another disc, iTunes went through the motions, no problem, then said it was finalising the disc, then suddenly said it was cancelling the burn, and "Attempt to burn a disc failed. An unknown error [4260] occurred". Again the first three tracks play okay, but the rest do not. The first 11 tracks are from an album I only downloaded yesterday, they play from the library and are authorised to play on my computer, so that's not the problem.
I can't find a reference to this particular error on iTunes support base online or in this forum. If anyone can help I'd be very grateful but I realise that it's a big problem for a lot of people. I don't understand why it worked alright before but now doesn't. I upgraded to the latest version of iTunes recently (v.6.0.4.2), so perhaps that's the problem?
Here is the report from the CD diagnostic run on iTunes:
Microsoft Windows XP Professional Service Pack 2 (Build 2600)
MICRO-STAR INTERNATIONAL CO., LTD MS-6330
iTunes 6.0.4.2
CD Driver 2.0.4.3
CD Driver DLL 2.0.3.2
LowerFilters: ASAPIW2K (6.0.2.0),
UpperFilters: InCDPass (4.3.14.1), incdrm (4.3.14.1), GEARAspiWDM (2.0.4.3),
Video Driver: NVIDIA RIVA TNT2 Model 64/Model 64 Pro\RIVA TNT2 Model 64/Model 64 Pro
Found aspi32 running.
IDE\DiskIBM-DPTA-372050_______________________P76OA30A, Bus Type ATA, Bus Address [1,0]
IDE\DiskST313032A______________________________3.09___, Bus Type ATA, Bus Address [0,0]
SBP2\GENESYSLOGIC&1394_TOIDE&CmdSetId104D8&GenDisk, Bus Type IEEE 1394
USBSTOR\DiskHP_____psc_2210_______1.00, Bus Type USB
IDE\CdRomATAPIDVD_RW_8XMax______________________130D___, Bus Type ATA, Bus Address [1,0]
IDE\CdRomLGCD-ROM_CRD-8521B_____________________1.04___, Bus Type ATA, Bus Address [0,0]
If you have multiple drives on the same IDE or SCSI bus, these drives may interfere with each other.
Some computers need an update to the ATA or IDE bus driver, or Intel chipset. If iTunes has problems recognizing CDs or hanging or crashing while importing or burning CDs, check the support site for the manufacturer of your computer or motherboard.
Current user is administrator.
F: ATAPI DVD RW 8XMax, Rev 130D
Audio CD in drive.
Found 22 songs on CD, playing time 75:39 on Audio CD.
Track 1, start time 00:02:00
Track 2, start time 04:26:60
Track 3, start time 08:06:35
Track 4, start time 12:29:15
Track 5, start time 14:48:47
Track 6, start time 18:31:10
Track 7, start time 21:31:12
Track 8, start time 23:43:07
Track 9, start time 26:55:27
Track 10, start time 29:40:62
Track 11, start time 32:54:35
Track 12, start time 35:06:00
Track 13, start time 38:08:42
Track 14, start time 41:35:50
Track 15, start time 44:56:25
Track 16, start time 48:27:45
Track 17, start time 52:18:55
Track 18, start time 56:08:45
Track 19, start time 59:15:15
Track 20, start time 62:38:27
Track 21, start time 66:04:40
Track 22, start time 70:58:45
Audio CD reading succeeded.
Get drive speed succeeded.
The drive CDR speeds are: 16.
The drive CDRW speeds are: 16.
The drive DVDR speeds are: 16.
The drive DVDRW speeds are: 16.
G: LG CD-ROM CRD-8521B, Rev 1.04
Drive is empty.
The last failed audio CD burn had error code 4260(0x000010a4). It happened on drive F: ATAPI DVD RW 8XMax on CDR media at speed 24X.
Thanks for any help. Anyone from Apple out there??
Mal
AMD Athlon XP 2000+ Windows XP Pro
AMD Athlon XP 2000+ Windows XP Pro

In case anyone reads this, I managed to burn my CD by changing the speed of the burn in iTunes. It was set on Maximum possible and I noticed from the CD Diagnostic report (see previous article) that the speed of the drive was listed as 16, but the burn had failed at 24x, so I reduced it to 12 to be safe, and it worked. It plays okay in the car but I have noticed that when I restart the player, it doesn't seem to recognise the CD and ejects it so that I have to push it back in, and it then starts at track 1 again. Not sure if this is to do with the way it was burned, but at least its playing the tracks!
Mal
AMD Athlon XP 2000+ Windows XP Pro

Syncing fails: unknown error (-50)

Using iTunes v.9.0.2 music syncs properly to my iPod touch with 3.1.2, but photos and films will not sync. Backup completes but then the sync stops with the warning:
"The iPod cannot be synced. An unknown error occured (-50)".
Any suggestions. The only ref I have seen to error (-50) relates to iTunes on Windows.

This is a big question here--I've seen it asked a lot and have found no answers. I visited a Genius Bar today and had no luck there either. There is an apple support document regarding it, but I can't access it, receiving an alert stating that the "language code supplied is not valid." The document I'm trying to see is labelled:
May get alert stating "Unknown Error (-50)" when syncing from iPhoto to iPhone, iPod, or Apple TV
May get alert stating " Unknown Error (- 50 )" when syncing from iPhoto to iPhone, iPod, or Apple TV
http://support.apple.com/kb/TS2985
Maybe you'll have better luck with it than I did. This seems to be a growing problem which Apple has yet to address. I can't sync my iPhone or AppleTV because of this condition, and the only workaround I've come up with is to create a new user account and move everything to that. It *****.

Im trying to publish a web gallery to BC, my settings seem correct but I'm still getting an error: FTP transfer failed ' unknown error'. Techs on BC, say FTP working fine. Please help!

Hey peeps,
Im trying to publish a web gallery to be hosted on BC. Despite having what seem the correct settings im getting an error: FTP transfer failed ' unknown message'. Have checked with techs on BC. They say FTP working fine that end.
Any suggestions?

Have you tried connecting to another FTP server in Lightroom?
For example, if you get a free Flickr account, can you login to it and upload a file to it?
If you can't upload to any server, then you have a general FTP-in-Lr problem, but if problem is only with BC then, well, it's time to start scrutinizing the BC settings..
PS - All my FTP'ing plugins have an enhanced FTP settings test feature designed to help you debug FTP settings, so another option is to download one of them, for example:
robcole.com - FTPAggregator
and experiment with settings tester:
To get here, you have to click 'View / Edit Additional Settings' (in plugin manager), then choose 'New' or 'Edit' from 'Sync Pairs' drop-down menu.
If test is unsuccessful, enable verbose logging (top section of plugin manager), and review the log file after test, or send to me.
If you have a problem running plugin, please contact me directly:
robcole.com - Contact Me
Rob

Encoding failed: unknown error in CS4 Windows 7

I'm getting the following error near the end of an Adobe Premiere CS4 sequence that I'm trying to encode:
- Source File: X:\scripts\rubyconf2009\premiere\19-nov-2009-14-10-east-meets-west-yuki-sonoda.prproj
- Output File: X:\scripts\rubyconf2009\premiere\19-nov-2009-14-10-east-meets-west-yuki-sonoda-large.mp4
- Preset Used: Custom
- Video: NTSC, 1280x720, 29.97 [fps], Progressive
- Audio: AAC, 64 [kbps], 48 kHz, Mono
- Bitrate: VBR, 1 Pass, Target 0,50, Max 1,00 [Mbps]
- Encoding Time: 01:03:33
25.01.2010 13:45:17 : Encoding Failed
Error compiling movie.
Unknown error.
I'm really not sure what the problem is. Everything seems fine in all my other movies but something in this one (and one other one) seem to be causing these failures. Any advice you could give would be really appreciated.

What are the source files in this (and the other offending) Project? Do they match those Sequence/Project Presets?
Does the Audio in these source files differ in any way?
What is different about this/these Project(s), from the others?
Often, Encoding will fail because of gaps in the Video. However, the error message is usually "Failure to Return Frame."
Good luck,
Hunt

"Attempting to copy to disk ipod failed unknown error occurred (-69)"

wat is happening to my ipod ? im using a 3rd generation 15gb ipod. after i try to refort using the lastest ipod updater it become like this ? and my connector is using a firewire. can any one help me with this ? pls .

ok in short it is like this
I have a fire wire ipod.
I know the device is recognized by the PC because it shows up in "my computer" and I can see what is on the ipod.
When I try to update the songs in Itunes the Ipod is recognized but updates fail.
The error reads: "attempting to copy to disk "IPOD" Unknown error -69"
I try to run the IPOD update /restore software and that give an error also.
"IPOD Manager internal error" and then the window closes.
so after everything i went to check my ipod drive to see if there is any folders in it . this is all i got calander notes and contacts. tat is all i have and if i put files into my ipod folders. it can. but it jus cant transfer music over from itune. man im at my wit end

Copying music failed, unknown error (-50)

Trying to move my library from one external hard drive to another external hard drive. Did it by going to Preferences-Advanced and changing the drive/folder location and then going to Advanced-Consolidate Library. All seemed to be going ok and then the process stopped (about 40% done) with the error "copying music failed. An unknown error has occurred (-50)". I've searched the forums and Google without luck. There was some mention of filenames. However, the songs with the longest pathname made it over to the new drive just fine. So it's not length. A quick check in iTunes using "GetInfo" showed some songs on the old drive and some on the new drive. At what point do these get updated in the consolidation process? As they are getting copied (one song at a time) or all songs before the copying process starts???
For the moment, I have changed the drive back and consolidated the library back to the original drive and that seems to be ok. Still want to move the library but don't know what caused it to stop the first time so thought I'd ask here before trying again.
Thanks.

hi usablues!
hmmmm. i've been seeing this particular kind of "anomalous" (-50) off and on since 4.9.
this is experimental. but we've been seeing different sorts of strange unknown error codes under similar circumstances when antivirus or antispyware is interfering with itunes' ability to read the library files.
... so ... can you get a consolidate to go through properly if you have your antivirus/antispyware switched off?
love, b

Importing changlist failed: unknown error has occured

Hello,
while importing a changelist from mas-test to mas-prod-system I get
error in transport service:
Importing changelist failed: unknwon error has occured, trying to reconnect.
I reinstalled the service, connections are ok, but this didn't solve the probelm.
What I have seen is that in the tile set 'imported changelist to be released'
my released changelist is about 25 times there - I think that is not normal.
Does anybody know where the problem could be ?
Thanks Gerd

Hi Gerd,
I don't know how to solve that particular issue but as a workaround I suggest to manually export and import the CL.
In 4.0 use these commands:
1. Export
Transport.exe /DBDars_db /DBUarsadmin /DBP /EXPexport /DIR"C:\temp" /CIDXX43748642B841409C5F03XXXXXXXXXX
where:
/DBD = Dsn of DB
/DBU = Administrator user(ARSAdmin)
/DBP = Password
/EXP = Operation(either export or import)
/DIR = Path to save the files to(during export) as well as path from where to pick up the CLs from(during import)
/CID = ChangelistID to be exported/imported
2. Import
Transport.exe /DBDars_db /DBUarsadmin /DBP /EXPimport /DIR"C:\temp" /CIDXX43748642B841409C5F03CXXXXXXXXX
If you are on .net use the Import / Export Manager. If you need that tool please contact me directly.
Regards
Whity

VIN 2 - Access failed. Unknown error...

Similar Messages

Maybe you are looking for