'Vintage' MacBook has lost all wifi connection suddenly and stored settings. I've tried to manually input my IP address and DNS number but it just times out when trying to connect to the network can anyone help?
'Vintage' MacBook has lost all wifi connection suddenly and stored settings. I've tried to manually input my IP address and DNS number but it just times out when trying to connect to the network can anyone help?
You said:
We still couldn't get it to stop timing out. I tried to download the firmware from iClarified but iTunes said it didn't recognise the software.
Just what did yo do to gt iTunes to see the download:
Similar Messages
-
its just all black and wont turn on or show any light. ive had it for about 2 years now. its a ipod touch 5th generation and blue not sure what to be but it has everything on it thats so important.. i need help and im unsure about the IOS :/
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
i m working in an organization where web-sense is installed to block all irrelevant sites, i have installed itunes but it does not run a window pops up with message 'itunes is not connected to the network' can anyone help me out?
There's a whole lot to read in your post, and frankly I have not read it all.
Having said that, this troubleshooting guide should help:
http://support.apple.com/kb/TS1538
In particular, pay attention to the mobile device support sections near the bottom, assuming you have already done the items above it. -
my ipod isnt turning on but it still makes a noise when i plug it into the charger can anyone help me?
Hey there cameronw99,
It sounds like you are unable to see your iPod Touch screen, as it stays black but it makes the connection tone when you plug in the USB cable. Use these steps to resolve the issue with the iPod from the following article:
iOS: Not responding or does not turn on
chttp://support.apple.com/kb/ts3281
If there is no video or if the screen remains black, verify that the device has enough charge to turn on:
If you are using an iPad, ensure that it's connected to the USB Power Adapter supplied with the device.
Let it charge for at least twenty minutes, then see if it starts normally.
If there is no image on the screen, press the Sleep/Wake button to attempt to wake the device.
If the screen displays a red battery icon, continue charging the device until the battery is fully charged. Learn more about charging iPhone and iPod touch, or iPad.
If the above steps do not resolve the issue, or the if the screen remains black or shows a persistent Apple logo, try restoring with iTunes:
Connect the device to your computer and open iTunes.
If the device appears in iTunes, select and click Restore on the Summary pane. Learn more aboutrestoring iOS software.
If the device doesn't appear in iTunes, try to force the device into recovery mode, and then restore it.
If the above steps do not resolve the issue, contact Apple.
Thank you for using Apple Support Communities.
Take care,
Sterling -
Hi, my ipad mini has suddenly stopped working and I cannot turn it off or connect it to the computer, can anyone help me on this??
Try this - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.) No data/files will be erased. http://support.apple.com/kb/ht1430
Frozen or unresponsive iPad
Resolve these most common issues:
• Display remains black or blank
• Touch screen not responding
• Application unexpectedly closes or freezes
http://www.apple.com/support/ipad/assistant/ipad/
iPhone, iPad, iPod Touch: Troubleshooting Touchscreen Response
http://support.apple.com/kb/ts1827
iPad Frozen, not responding, how to fix
http://appletoolbox.com/2012/07/ipad-frozen-not-responding-how-to-fix/
iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
Black or Blank Screen on iPad or iPhone
http://appletoolbox.com/2012/10/black-or-blank-screen-on-ipad-or-iphone/
What to Do When Your iPad Won't Turn On
http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
iPad: Basic troubleshooting
http://support.apple.com/kb/TS3274
Cheers, Tom -
I need to export a photo at around 1meg file size,and dont seem to be able to do it in the presets can anyone help please ,I shoot on a canon 5d
I believe Frank is referring to the end use (e.g., for print or on-screen use).
Until he returns, I can tell you that I ran a quick test using an image from the Aperture 3 training book library which was as follows:
Camera = Canon EOS 5D Mark II
Master resolution = 5616 x 3744 (21 MP)
I was able to export to a JPEG with end file size of 1 MB as follows:
Export Presets drop-down > select 'Edit' option
Selected preset name 'JPEG - 50% of Original Size' > change percentage value to 40% > change DPI value to '300' > click OK to set as current default > Export version to desktop.
The exported JPEG has a resolution of 2246 x 1498 and appears on screen to have the same image quality of the original in Aperture.
Note - I did not change the default Image Quality slider in the Export Preset dialog (which left it at 10).
Basically, you will need to play around with the settings until you find the appropriate values to arrive at an image version you want. -
I'm new to iPhone and iCloud... I have lots of pics on my iPhone but only some appear on my iPad, they're in Camera Roll on the phone but random ones only have come into Photos on the iPad - can anyone help? Thanks!
Welcome to the Apple Community.
Photostream when enabled will only add photos from the camera roll that were taken post photostream activation. (Photostream does not currently share video)
Photostream only syncs photos over Wi-Fi, make sure you are connected to Wi-Fi to begin with.
Photostream only syncs when the camera app is closed, ensure it is closed.
Photostream only syncs when the battery is above 20%, try recharging the device
Try disabling photo stream on your device (settings > iCloud), restarting your device and then re-enabling photo stream. -
My ipad 1 isnt working it is just showing the apple logo on the screen can anyone help me?
my ipad 1 isnt working it is just showing the apple logo on the screen can anyone help me?
If you can help me facetime me at [email protected] or msg me.It would help to know whether it ever did work, or is this a new iPad for you? If new, you need to connect it to a Mac/PC that's running iTunes in order to register and initialize it. If it used to work, try doing a reset.
-
Hi.Since I upgraded to Maverick my scanner which is Fuji Xerox Docuprint CM205 fw could not be used for scanning as mac wouldn't find the scanner.Can anyone help please?
There's an alternative ...
Using Image Capture as a scanner:
Connect the scanner to your Mac whether Wi-Fi or USB.
Launch Image Capture.
Click the very small black box bottom right side of the Image Capture window.
You'll see this pop up menu: Connecting this (device) opens:
You can select a default app to scan (Image Capture) and select a folder from the Imort To pop up menu on the right to save scanned files to. -
My LR2 is missing the templates can anyone help?
I am in LR2, print mode/contact sheet/grid. I have 36 photo's I am attempting to template in a 4x5 contact sheet.
However my templates are empty and I am so new to the program I do not know what to do. This assignment is due today and I have ran out of options on what to do or where to go.
When I click on the contact sheet/grid it is only showing me one of the 36 photos I have and according to the school tutorial it is suppose to show me all the pictures.
Can anyone help???? I am so very lost and frustrated.It was until my son came home and said, "Mom you have to do it like this......" I feel like such an idiot. I do thank you for asking.
My other issue is that every time I attempt to move the pictures from my memory card in RAW format into LR2, it tells me the files or corrupt. However I can use my other conversion program and they will convert. The only issue with this is it makes my teacher mad that I am not doing it through LR2. I do not know why it is telling me the RAW files are corrupt and the other program will open them.
This has been my luck with this program, and yes I am new to using it.
Thank you for your time.
Thank you!!Tammy
EMAILING FOR THE GREATER GOOD
Join me
Date: Mon, 16 Nov 2009 17:09:21 -0700
From: [email protected]
To: [email protected]
Subject: My LR2 is missing the templates can anyone help?
Just so I'm clear, you're saying that the 2nd panel from the top on the left side of the screen called "Template Browser" is empty?
DLS
> -
i connected to itunes and it says i have 2.11 GB of space taken up under OTHER , i cant figure out what is taking up so much space can anyone help?
I believe the new IOS 8 system takes up 1.3 Gb on it's own. Then plus anything else you may have loaded.
-
I have an error message coming up when trying to send an email which says 'sending the message failed because you're exceeding the limit' can anyone help me to resolve this please
Try reentering the password in your iCloud mail settings.
-
neither my ipad or ipod are being recognized by itunes so i can't transfer songs from itunes playlists to the two devices. this is new, as far as a week ago i transferred music from the computer to the ipod. can anyone help?
Hey lightc,
If you are having an issue with iTunes not recognizing your iPad and iPod on your Windows computer, I would suggest that you troubleshoot using the steps in this article -
iPhone, iPad, or iPod not recognized in iTunes for Windows
Thanks for using Apple Support Communities.
Happy computing,
Brett L -
When publishing a captivate I get the message "Swf compilation failed. Note: Please verify if any of the actionscript keywords is used as user variable name." and it won't allow me to publish the Captivate, can anyone help?
Hi There,
Can you tell me the Operating System and Captivate version you are using?
Also can you confirm if you are getting this issue will this one project or all the projects? Try to copy paste this project on a new blank project and then try to publish.
Regards,
Mayank -
My backlight is always on,im unable to off the light,can anyone help me?
my backlight is always on,im unable to off the light,can anyone help me?
This discussion may help.
It mostly depends on the camera. Some cameras have a Transfer Mode, which does not attempt to charge while transferring pictures. does yours have such a setting?
Alternatively you can try to plug a powered USB hub between the camera and the USB connector so the power is provided by the HUB rather than the iPad.
Other than that, yes the Memory card reader may be a better option assuming your Camera uses Secure Digital (SD) type memory cards.
Maybe you are looking for
-
How can i connect home sharing and the control app with 2 IP addresses?
i am using my macbook pro at school and i also take it back home, and when i'm home the home sharing with my iPhone 5's Remote app works perfectly fine, just that when i'm back to res at school it doesn't work for some unknown reason. i've checked ev
-
Standard way of Handling Escalation process in CRM Complaint Management
Dear experts, What is the standard way of mapping Escalation process in SAP CRM Complaints management? We need to escalate the complaint to next level if it is not resolved with in the a specific time. How can we configure this scenario in SAP CRM. P
-
ITunes won't pull up the songs on my iPod!!!!
Just updates to iTunes 7, and everytime I try to access the songs on my iPod, it gives me a list of utter garbage: Summary, Musci, Movies, TV Shows, etc. When I click on "Music", it asks me if I want to sync my iPod and my library, thereby erasing ev
-
File To File with merging and two sources one receiver.
Hi Experts, My scenario is File to File In this I need to pick Files from two different Directories on different systems: Sys1 and Sys2 In Sys1 i have 7 Files File1 to File7 In sys2 i have 8 Files File 8 to File14 and File_EOPM Now <B>I need to merge
-
Hello There's a page which contains the following 3 components: Input textfield, Button, Tree I made the following settings of them: I set the "event action" at the tree node, and so did I at the button properties. When I click on the button, the act