Virtual Appliance for FirePOWER appliance

Hello folks,
I've got some questions re: FirePower appliance. We have mixed up environment from ASA 5505/5520/5540 to ASA 5525X models. We know we can get a software module on X model and start using FirePOWER - PoC completed.
Here's the concern:
- Can we use FirePOWER standalone appliance to integrate with traditional ASA firewalls?
- Is there ANY virtualization options because we do not want to buy hardware
Your answer would be greatly appreciated!
Thanks
G1

You can put the Cisco-branded legacy Sourcefire hardware appliances in line with your older (or newer) ASAs that don't have FirePOWER modules.
You can similarly route your traffic through a virtual sensor if your VMware ESXi (or Xen or RHEV) hosts can be configured to sit in the proper place in your network. Here is a link to the data sheet (still in the old Sourcefire salesforce.com location).

Similar Messages

Error when installing virtual appliance for r12.2.4

Hello
I have downloaded Oracle Virtual Appliance for Oracle E-Business r12.2.4 in a following step by step manner but I am running into an error. As per the readme, I have gone through the Note:1928303.1 but it does not address the issue.
That said, is there any comprehensive, step by step document that outlines installation and implementation of Oracle Virtual Appliance for r12.2.4?
Below are steps I ran.
Step 1: Downloaded and Installed Oracle Virtual Box version 4.3.22.
Step 2: I want to install Oracle EBS r12.2.4 single node installation on My Windows 8.1 64 bit laptop with 1 TB of HDD and 8GB RAM.
Step 3: Downloaded following files for single node vision appliance.
There are two zip files for each part, so I downloaded total 16 zip files.
V52470-01 Oracle E-Business Suite Release 12.2.4 Single Node Vision Install X86 (64 bit) (Part 1 of 8) Linux x86-64
V52471-01 Oracle E-Business Suite Release 12.2.4 Single Node Vision Install X86 (64 bit) (Part 2 of 8) Linux x86-64
V52472-01 Oracle E-Business Suite Release 12.2.4 Single Node Vision Install X86 (64 bit) (Part 3 of 8) Linux x86-64
V52473-01 Oracle E-Business Suite Release 12.2.4 Single Node Vision Install X86 (64 bit) (Part 4 of 8) Linux x86-64
V52474-01 Oracle E-Business Suite Release 12.2.4 Single Node Vision Install X86 (64 bit) (Part 5 of 8) Linux x86-64
V52475-01 Oracle E-Business Suite Release 12.2.4 Single Node Vision Install X86 (64 bit) (Part 6 of 8) Linux x86-64
V52476-01 Oracle E-Business Suite Release 12.2.4 Single Node Vision Install X86 (64 bit) (Part 7 of 8) Linux x86-64
V52477-01 Oracle E-Business Suite Release 12.2.4 Single Node Vision Install X86 (64 bit) (Part 8 of 8) Linux x86-64
Step 4: Unzipped these files
Step 5: After unzip, unzipped filename looked like following. So I removed the last digit in the extension so that Oracle virtual box can recognize .ova extension.
Unzipped file name:
Oracle-E-Business-Suite-12.2.4_VISION_INSTALL.ova.01
renamed to
01_Oracle-E-Business-Suite-12.2.4_VISION_INSTALL.ova
Step 6. In Oracle virtual box, attempted to import these ova files using "Import Appliance". This is when I am getting following error.
Oracle VM Virtual Appliances for Oracle E-Business Suite (Linux)
Failed to import appliance C:\ova\EBS\INSTALLATION OPTIONS\Option 1 Single Node ALL\0_Oracle-E-Business-Suite-12.2.4_VISION_INSTALL.ova.
Could not create the imported medium 'C:\Users\ova\VirtualBox VMs\Oracle-E-Business-Suite-12.2.4_VISION_INSTALL\Oracle-E-Business-Suite-12.2.4_VISION_INSTALL-disk1.vmdk'.
VMDK: Compressed image is corrupted 'C:\Users\ova\Oracle-E-Business-Suite-12.2.4_VISION_INSTALL-disk1.vmdk' (VERR_ZIP_CORRUPTED).
Result Code: (0x80BB0004)
Component: Appliance
Interface: IAppliance {3059cf9e-25c7-4f0b-9fa5-3c42e441670b}
This is happening with each and every file in above list.
Please advise what am I missing? And if there is a comprehensive document somewhere that outlines details about implementation. The above mentioned metalink note is not enough.
Darsh

You need to merge all of the downloaded files first, before importing into Virtualbox. Google for my blog for detailed steps.

Is there an associated Linux GUI Desktop available with the VM Virtual Appliances for Oracle E-Business Suite 12.2.4 64 bit or is it all command line?

I have downloaded the 16 pieces of Oracle VM Virtual Appliances for Oracle E-Business Suite (12.2.4) for x86 64 bit V52470-01 Parts 1 & 2 thru V52477-01 Parts 1 & 2 and unzipped and created the .ova.
I then imported that into VBox 4.3.22.
I went thru and changed the passwords for root, oracle, and applmgr as requested and entered a static IP.
I have not configured the DB or Applications yet.
However, I want to know if there is a typical GUI Desktop that can be brought up.
Thank you.

I have not been able to find a GUI desktop - I believe it is disabled or not included in the media.

Virtual Appliance for Solaris 10

I am planning to be running Solaris on windows with help of VMware player. Could anyone please guide me to the exact and recent download link for the disk image of preinstall solaris 10 virtual appliance.
Since this would be my first hands on VMware and initial setup guide will be very much appreciated.
Thank you!
unix.sagi

Try the Virtual servers on Sun's Developer site.
http://developers.sun.com/solaris/downloads/solaris_apps/index.jsp
or check out the OS category on VMware's Marketplace.
http://www.vmware.com/appliances/directory/cat/45

Is there any Ironport Virtual Appliance for Testing Purpose ?

Hi Everyone,
Advance Thanks to Every One.
Is there any Ironport Virtual Appliance for Testing Purpose ?
Regards,
Bala Krishna G

Looks like there are a couple of vendors who have virtual options. Here's one.
http://www.ironportstore.com/VirtualEvalRequest.asp
Also, IronPort has a 30-day free trial of their product.
http://pages.ironport.com/evalrequest.html?source=eval_req
Hope this helps.
Brandon

Can ISE 1.2 Virtual Appliance assign VPN address pool like ACS does?

Dear friends,
I have observed that Cisco ISE Virtual Appliance (VMware) can act as a RADIUS server in the same manner as ACS does, but I cannot find the way of assigning an IP address to a remote VPN client (only assigning a VLAN).
At this point I don't know if it is strictly necessary to have the IP address assignment for the remote VPN clients done in the external firewall (i. e. Cisco ASA) in this case.
Is there any way of defining an IP address pool in the ISE itself for VPN clients authenticated against that ISE?
If the answer is not, which ones could be the options for that assignment other than the ASA pool assignment? Could it be possible defining the corresponding address pool in an internal DHCP server that could provide the IP address to the VPN client after successful authentication through ISE?
Any help would be really appreciated to clarifying these questions.
Thank you and best regards.

Please find the link below for the may help you to get the answer related to comparision and even for deployment.
http://pmbuwiki.cisco.com/Products/ISE/Technical/Design-Config/Guest_and_Web_Portal_Services

LMS 4.2.2 virtual appliance fresh install : DCR Server Error

Hello,
I have installed a new version of LMS 4.2 on virtual appliance (VMware 4.1) and I have an issue.
When I go the "Device Administration --> Manage Device State" I have the following error :
Server Error
Error
Error in communicating with DCR Server. For more details click here.
DCR Server may be down. Please start the DCR Server and then refresh the page.
Following the details link I have : (I did all the check written below).
DCR Server Error
The communication error may be due to the following reasons:
The DNS resolution does not match with server assigned IP Address. Workaround: DNS resolvable IP Address should be same as server IP Address. DHCP is enabled in the server. Workaround: DHCP should be disabled in the server. The server’s original IP Address may have changed. Workaround: Restart Cisco Prime Daemon Manager. CTM registry corruption has occurred due to rebooting the server without stopping the Cisco Prime Daemon Manager. Workaround: Delete the ctmregistry and ctmregistry.backup file in NMSROOT/MDC/tomcat/webapps/cwhp/WEB-INF/LIB and then restart the Cisco Prime Daemon Manager. DCR Server and related process might be down. Workaround: Check the processes to make sure DCR Server is running, and restart it if not. The hostname change is not done by the hostnamechange.pl in LMS. Workaround: Hostname change should be done using NMSROOT/bin/hostnamechange.pl in LMS. LMS self signed certificate would have been expired. Workaround: Regenerate the certificate and restart the daemon manager.
I try to reinstall LMS 4.2 with or without patches 4.2.1 and 4.2.2 I always have the same problem. The DCR server process is running.
Here the result of the show application status LMS in SSH :
S-CISCO-LAN-MS/sysadmin# show application status LMS
Process               State                                     Pi
d
ESS                   Program started - No mgt msgs received    27
14
EssMonitor            Running normally                          29
50
EventFramework        Program started - No mgt msgs received    32
95
SyslogCollector       Running normally                          32
96
RMEDbEngine           Program started - No mgt msgs received    32
97
DfmBroker             Running normally                          34
24
DfmServer             Running normally                          36
62
DfmServer1            Running normally                          36
63
FHDbEngine            Program started - No mgt msgs received    36
64
EPMDbEngine           Program started - No mgt msgs received    40
81
EPMServer             Running normally                          42
20
AdapterServer         Program started - No mgt msgs received    43
20
AdapterServer1        Program started - No mgt msgs received    43
21
FHServer              Running normally                          43
22
INVDbEngine           Program started - No mgt msgs received    43
23
PMServer              Running normally                          4582
IpmDbEngine           Program started - No mgt msgs received    4708
UPMDbEngine           Program started - No mgt msgs received    4840
UPMDbMonitor          Running normally                          4949
ANIDbEngine           Program started - No mgt msgs received    4953
MACUHIC               Running normally                          4990
UTLITE                Running normally                          4991
CmfDbEngine           Program started - No mgt msgs received    4992
CmfDbMonitor          Running normally                          5104
DFMLogServer          Program started - No mgt msgs received    5106
DFMCTMStartup         Administrator has shut down this server   0
FHPurgeTask           Never started                             0
DFMMultiProcLogger    Program started - No mgt msgs received    5108
CSDiscovery           Never started                             0
DCRDevicePoll         Never started                             0
CSRegistryServer      Running normally                          5109
Tomcat                Program started - No mgt msgs received    5110
TomcatMonitor         Running normally                          5206
Apache                Running normally                          5567
DCRServer             Running normally                          5580
CMFOGSServer          Program started - No mgt msgs received    5641
TISServer             Program started - No mgt msgs received    5642
DFMOGSServer          Program started - No mgt msgs received    5757
NOSServer             Running normally                          5795
PTMServer             Running normally                          5796
InventoryCollector    Running normally                          5797
Interactor            Program started - No mgt msgs received    5885
InventoryCollector1   Program started - No mgt msgs received    5886
Interactor1           Program started - No mgt msgs received    6116
UPMProcess            Running normally                          6117
WlseUHIC              Running normally                          6118
UTManager             Running normally                          6119
VNMServer             Program started - No mgt msgs received    6120
EssentialsDM          Running normally                          6121
ICServer              Running normally                          6310
EnergyWise            Running normally                          6581
ConfigMgmtServer      Running normally                          6582
PMCOGSServer          Program started - No mgt msgs received    6583
ConfigUtilityService Running normally                          6584
CAAMServer            Running normally                          6585
IPMOGSServer          Program started - No mgt msgs received    6586
TopoServer            Program started - No mgt msgs received    6587
LicenseServer         Program started - No mgt msgs received    6588
FDRewinder            Never started                             0
NameServer            Program started - No mgt msgs received    6591
NameServiceMonitor    Program started - No mgt msgs received    6792
EDS                   Running normally                          6870
ANIServer             Running with busy flag set                7224
UTMajorAcquisition    Never started                             0
EDS-GCF               Running normally                          7257
jrm                   Running normally                          7258
DataPurge             Administrator has shut down this server   0
IPMProcess            Program started - No mgt msgs received    7535
CTMJrmServer          Administrator has shut down this server   0
SyslogAnalyzer        Never started                             0
ChangeAudit           Never started                             0
diskWatcher           Running normally                          8381
I run out of ideas...
Regards,
Abel

Hi Afroz!
Thanks for the quick reply!
1) I checked files - and indeed, the third link of the file was empty.
I restored contents of the same test server (as an attachment - original files) - now everything is working fine. Many thanks for your advice!
Because of what could this happen?
Current settings are as follows (i did not change them):
[lms42/root-ade etc]# ls -la /opt/CSCOpx/MDC/tomcat/shared/lib/ctm_config.txt
-rw-r--r-- 1 casuser casusers 1037 Jul 22 13:54 /opt/CSCOpx/MDC/tomcat/shared/lib/ctm_config.txt
[lms42/root-ade etc]# ls -la /opt/CSCOpx/MDC/tomcat/webapps/cwhp/WEB-INF/lib/ctm_config.txt
-rw-r--r-- 1 casuser casusers 1084 Jul 22 13:54 /opt/CSCOpx/MDC/tomcat/webapps/cwhp/WEB-INF/lib/ctm_config.txt
[lms42/root-ade etc]# ls -la /opt/CSCOpx/MDC/tomcat/lib/ctm_config.txt
-rwxr-xr-x 1 casuser casusers 1104 Aug 20 12:07 /opt/CSCOpx/MDC/tomcat/lib/ctm_config.txt
2) It was also noted that if address on the link "Inventory>Device Administration>Discovery>Schedule", then an error message appears:
Error
Error in getting the Discovery configuration information, please configure Standard / Custom Discovery and start the schedule.
- no any records for Discovery Schedule and not accessible button Add (for add new Discovery Jobs).
This is related errors?

LMS 4.2 virtual appliance: How to export archive devices configs on a network drive

Hello,
I will install a new LMS 4.2 based on a virtual Linux Red Hat appliance.
I would like to export archive devices configurations based on /var/adm/CSCOpx/files/rme/dcma/shadow on an external drive.
Do we have embedded tools on LMS 4.2 Linux to share a network drive or do we use NFS commands ?
Thanks for your help.
Patrice

there are no such embedded tools.
I am awaiting Ciscos return with a solution for bringing the backup out of the VA (Virtual Appliance) and to a safekeeping place.
Same issue all around - the VA is now a client only !
I saw a hack around the SCP user inorder to use WinSCP for faster file browsing etc, and that might work, but I want a supported fix for this issue. And by that I mean Cisco needs to tell me what can be done and how its supported.
please share any knowledge you might get on this topic.

Demo License key issue in Cisco Content Secuirty managment Virtual appliance

Hi,
I have installed a Cisco content security management appliance for customer evaluation. I have downloaded 45 day demo license key but unable to update the license key neither in GUI nor in CLI. I have referred installation guide and user guide but did not helped at all.
Snapshot from GUI

Would suggest to re-copy and paste the XML license - as most likely you have extra white space that is causing the malform when pasting/loading. If using Windows, try avoid using wordpad --- and use Notepad++ or similar.
http://www.cisco.com/c/en/us/support/docs/security/email-security-virtual-appliance/118301-technote-esa-00.html
-Robert

Virtual appliance oel5u5-64bit-soabpm-11gr1-ps5-2-0-M: Can't deploy

Greetings,
After having installed the mentioned virtual appliance and created the dev_bpm domain, trying to deploy from Jdeveloper to app server raises the following:
[04:55:41 PM] Deploying profile...
[04:55:42 PM] Updating revision id for the SOA Project 'SalesQuoteToContractDemo.jpr' to '1.0'..
[04:55:43 PM] Wrote Archive Module to /home/oracle/jdeveloper/mywork/FusionNX_Application/SalesQuoteToContractDemo/deploy/sca_SalesQuoteToContractDemo_rev1.0.jar
[04:55:43 PM] #### Deployment incomplete. ####
[04:55:43 PM] No SOA configured servers found for deploying the archive file:/home/oracle/jdeveloper/mywork/FusionNX_Application/SalesQuoteToContractDemo/deploy/sca_SalesQuoteToContractDemo_rev1.0.jar
(oracle.tip.tools.ide.fabric.deploy.common.SOARemoteDeployer)
It seems that the admin server in the dev_bpm domain is not configured for SOA. However, the documentation says:
"This domain is configured using the development template for SOA and BPM, which targets all the SOA and BPM applications to the AdminServer."
What am I doing wrong ?
Kind regards,
Nicolas

Does any body feel concerned ?

Upgrade path from Riverbed Whitewater V110 to AltaVault Virtual Appliance

Hi,
We have users on the V110 model of the virtual appliances of Whitewater (Riverbed edition) that haven't transitioned to the NetApp varients as yet.
What would be the upgrade path if they wanted to keep running a virtual on-premise SteelStore/AltaVault?
Would there need to be an intermediate step to SteelStore 3.2 between Whitewater (3.1.2a) and AltaVault?
Thanks
Garth

Hi Garth,To get to the AltaVault release, you'll do this in 2 phases. 1. Upgrade the software. This is done by downloading the 3.2.2 code from mysupport.netapp.com and then installing it on the current v110. Use the Configure > Maintenance > Service page to stop the optimization service, then use the Configure > Maintenance > Software upgrade page to update it with the downloaded image. Reboot after the update is done. 2. Migrate to AltaVault software. This is done by following the instructions in Appendix A. of the Install Guide for Virtual Appliances:https://library.netapp.com/ecm/ecm_download_file/ECMP12455064 Regards,Christopher

Cisco ISE Virtual Appliance HyperV Support

Hi,
ISE Virtual Appliance Supports VMWare ESXi as Hypervisor. Is there any Plan on the roadmap that ISE will be supported on HyperV (or possibly XEN) in the future, because some customers don't have VMWare but using only HyperV.
The same question may be for other Virtual Appliances as well such as vWAAS, vASA etc.
Best Regards,

David,
There is currently no documentation on this process. This is not a supported installation/upgrade/migration path so, therefore, any documentation would be third party, prepared by the partner or end user that has done this.
If you're starting from a VM, you have the wrong approach. You'll want to install from .iso for best results.
Please Rate Helpful posts and mark this question as answered if, in fact, this does answer your question. Otherwise, feel free to post follow-up questions.
Charles Moreton

Oracle VM Virtual Appliances

Hi all,
Oracle VM Virtual Appliances for Oracle E-Business Suite Deployment Guide, Release 12.2.4 (Doc ID 1928303.1)
The docs said that:
But when I login to root on my VM system, and run :
[root@db etc]# cat /etc/oracle-release
Oracle Linux Server release 6.6
Does this mean the doc is not updated? or the /etc/oracle-release is not updated?
Please help how to check.
Thanks a lot,
mk

Hi,
I know that this is an old discussion and you probably figured out the answer yourself.
Just to publish an answer and close it, the document is not up to date with the software you downloaded.
Nothing to worry about.
Regards,
Bashar

Question about ANM Virtual Appliance ESX support

Hello,
I have a question:
I need to install ANM 5.2 on a virtual appliance (using the .ova file).
What ESX and vSphere versions does ANM 5.2 support?
I don't see any information regarding this on the release notes or installation guide.
Thanks.

Looks like the only requirement is Vcenter and Vsphere 4 client. So version 4.0 and up is supported.
http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/application_networking_manager/5.1/device_support/table/sdt.html
ANM 5.2 and 5.1 includes a plug-in that allows you to integrate ANM into a VMware virtual data center environment. VMware is a third-party product for creating and managing virtual data centers. Using VMware vSphere Client, you can access ANM functionality and manage the ACE real servers that provide load-balancing services for the virtual machines in your virtual data center.
To use the ANM 5.2/5.1 plug-in, you must use VMware vCenter Server and VMware vSphere Client 4.
For more information about using ANM in a VMware virtual data center environment, see the User Guide for the Cisco Application Networking Manager 5.2/5.1.

Oracle BigDataLite Virtual Appliance confirmation

I'm trying to follow the instructions for installing the
Oracle BigDataLite Virtual Appliance
Oracle BigDataLite Virtual Machine
I'm running VirtualBox 4.3.6
7-Zip 9.2
Running on Windows 7 Home Premium 64 SP1 with AMD FX 8120 with 16 GB (a stock aspire M3450)
And there seems to be a disconnect in the PDF for the quickdeploy, as if in the rush to create the quick deploy document something was left out, or the process was not tested before posting for download
Specifically: from the PDF
After all zip files are downloaded, extract them with 7zip.
In Windows:
Right-click on file BigDataLite-xxx.zip.001 file and select 7-zip->Extract Here
The extraction will create the BigDataLite-xxx.ova appliance file.
Well the above is NOT happening
First the files are named at OTN as
BigDataLite-2.4.1.001
BigDataLite-2.4.1.002
BigDataLite-2.4.1.003
BigDataLite-2.4.1.004
BigDataLite-2.4.1.005
BigDataLite-2.4.1.006
Not as the naming convention in the PDF documentation which is requesting a .zip.001 extension
Can someone run a confirmation that a ova file can be created?

Thanks for replying:
I'm getting the correct checksum for 4-5-6
What seems to be happening is that I'm getting a bad download
Bad Checksum
md5sum BigDataLite-2.4.1.001
70728c177aee531710804183d9ba407b
Not
0eefb04ec725b2aba21c017f0c54ccfd
md5sum BigDataLite-2.4.1.002
fe8fd773feadc01b08f4cdc802b188db
Not
a19c4d8713a7ec0b765a831e710db04e
md5sum BigDataLite-2.4.1.003
997670eb5f5d9cd8c66f2a071415d738
Not
83f35179b44c58b50e2e19d36701b5df
I'm downloading "yet again", even if you did get good files then could you do me the favor of downloading any of the three and confirming the issue?
Possibly tossing a file in some dropbox app that works?
I hate asking, but what you got at dev-days on media might not be the same?
I'll give you a helpful for the response, but honestly I usually don't mess these things up, get to one reston way myself... and believe there is an issue
But again thanks
BigDataLite-2.4.1.004, BigDataLite-2.4.1.005, BigDataLite-2.4.1.006 were correct

Problems to download the VIRTUAL APPLIANCE of LiveCyle ES

Hi,
I tried to download the VM offered at Download the Evaluation Virtual Appliance trial of Adobe LiveCycle Enterprise Suite Update 1 but the given user & password failed. In addition the FTP Help link just leads back to the main ES page ?!
Mailed to Adobe help : NO ANSWER SINCE 2 days !
Does anybody succededd with downloading the VM ?
Any hints are welcome.
snoopje

I tested it from a Windows command prompt (using the Windows FTP client) and it does not work right now. Adobe is closed this week but we will get this fixed next week. Sorry about the inconvenience.
ftp eftp.adobe.com
Connected to eftp.adobe.com.
220-GlobalSCAPE Enhanced File Transfer Server (v. 5.0)
220-Welcome to eftp.adobe.com!
220 ###########################################################
User (eftp.adobe.com:(none)): lc-trial
331 Password required for lc-trial.
Password: livecycle
530 Not logged in.
Login failed.
ftp> quit
221 Service closing control connection.

Virtual Appliance for FirePOWER appliance

Similar Messages

Maybe you are looking for