Visio Stencil for HWIC-1GE-SFP
Does anyone know if there is a visio stencil for the HWIC-1GE-SFP for a 2951 router? I have looked through the index of stencils, but it is not listed there. Any suggestions would be appreciated. Thanks!
Gil
Hi Bruno,
I have just emailed the product group to request funding for the following:
EHWIC-4ESG
EHWIC-4ESG-P
EHWIC-D-8ESG
EHWIC-D-8ESG-
EHWIC-4SHDSL-EA
EHWIC-1GE-SFP-CU
Those are all of the EHWIC module part numbers that I could find. We are dependent upon the product groups to authorize and fund the Visio work and hopefully I will hear from them soon.
Regards,
Brett Newman
Cisco Visio Production
Visimation Inc.
www.shapesource.com
Similar Messages
-
Visio stencil request - EHWIC-1GE-SFP-CU
I need a visio stencil for the EHWIC-1GE-SFP-CU module. I can't find it in the Cisco Visio Stencil packages that are readily available on cisco.com.
Any chance I can get one of these, or does anybody know where it can be found?
Thanks for your helpHi Bruno,
I have just emailed the product group to request funding for the following:
EHWIC-4ESG
EHWIC-4ESG-P
EHWIC-D-8ESG
EHWIC-D-8ESG-
EHWIC-4SHDSL-EA
EHWIC-1GE-SFP-CU
Those are all of the EHWIC module part numbers that I could find. We are dependent upon the product groups to authorize and fund the Visio work and hopefully I will hear from them soon.
Regards,
Brett Newman
Cisco Visio Production
Visimation Inc.
www.shapesource.com -
Hi,
I'm trying to use a HWIC-1GE-SFP and it doesn't seem to support Fast ethernet.
It seems to just support Gig eth full duplex because there are no configurable options for speed or duplex. Is this just an IOS issue that might be rectified in later revisions? or is there any way to work around this?Hi,
HWIC-1GE-SFP only supports 1000 Mbps in full duplex. "Speed" or "duplex" commands are not supported under the interface.
http://www.cisco.com/en/US/products/ps5855/products_qanda_item0900aecd80169bf0.shtml
HTH, Please rate if it does.
-amit singh -
I want to download Visio Stencils for ADF Faces
Dear members
I read about Visio Stencils for ADF Faces and I really Like it.
https://blogs.oracle.com/jdeveloperpm/entry/adf_faces_stencils_for_visio_available_on_samplecode
And I want to download it. Has any one tried it before.Can any one tell me where can I download it.
The articular says that it is Available through samplecode.oracle.com but i cannot find it
please help
thankshttp://www.oracle.com/technetwork/indexes/samplecode/jdeveloper-adf-sample-522118.html
Still down to http://download.oracle.com/otn/samplecode/ADF_Faces_Stencils_for_Visio.zip
you need to accept the license before download.
Timo -
Unable to find visio stencil for 6506-E FourX Adapter
Hi
Where can i find the visio stencil for Cisco 6506-E FourX Adapter for 10 Gigabit Ethernet Mode. I found the WS-X6904-40G-2T module but I unable to find the FourX 10G Adapter for it.
Thanks in advance,
Martin JohnHi,
I was also getting same error, which is solved now.
For reference following is what we need to check.
- Proper mapping of source data to endeca dimension is made.
- You have made entries in "dimension_values.csv" but dimension is not specified in "schema.csv"
HTH
MS -
I've been searching but i can't find the visio stencil for the ACE-10 or ACE-20 module.
Can anyone point me in the right direction or is this stencil yet to be made ?I don't think they are available yet. I needed them a few months ago, couldn't find them, and ended up making my own.
In case you need it, here's a link to the stencils Cisco provides.
http://www.cisco.com/en/US/products/prod_visio_icon_list.html -
Visio stencil for ASA 5585-X?
Hello,
Can anybody help pointing me to where I can get a visio stencil for a asa-5585-x.
I really appreciate it.
Thanks,
JohnHi John,
The official Cisco Visio stencils can be found here:
http://www.cisco.com/en/US/partner/products/hw/prod_cat_visios.html
I don't see the 5585 there yet, but once it's available that set should be updated.
-Mike -
Hi
Would it be possible to update the Visio stencils for the Unified Computing System. There are a number of servers missing as the stencil hasn't been updated since 2012, one in particular is missing and that's the C240M3 LFF chassis. Also there is no option for disks etc
Many thanks
MikeI too am looking for stencils. Even the Voice_IP_phone stencil is
missing all the new series phones, such as the 69xx, 89xx and 99xx models.
Anyone know where to even open a request for the new ones, or is everyone not using Visio anymore? -
Visio Stencils for Cisco Equipment
Does anyone know where you can obtain some good visio stencils for cisco equipment like routers, switches, gateways, cables, ports, etc. The default ones in Visio leave much to be desired. Any input appreciated - thanks.
I too am looking for stencils. Even the Voice_IP_phone stencil is
missing all the new series phones, such as the 69xx, 89xx and 99xx models.
Anyone know where to even open a request for the new ones, or is everyone not using Visio anymore? -
Hi all,
May I know how many vlan can HWIC-1GE-SFP support?
Thanks
makHello Mak,
I think there is no limit related to the card itself. The limit would be the speed of the card (1 Gigabit); I do not see a relationship between the amount of VLANs carried over the interface other than that 1 Gigabit.
Check these two links, they do not actually relate to your question, but might be useful anyway:
Cisco Gigabit Ethernet High-Speed WAN Interface Card
DATA SHEET
http://www.cisco.com/en/US/partner/products/ps5949/products_data_sheet0900aecd8016be8d.html
Cisco Gigabit Ethernet High-Speed WAN Interface Card
Q&A
http://www.cisco.com/en/US/partner/products/ps5949/products_qanda_item0900aecd80169bf0.shtml
HTH,
GP -
Does anyone have current Visio stencils for the newer wireless products?
Does anyone have the latest Visio stencils for Cisco's wireless products? Specifically looking for 3502 and 1260 series access points and the 5508 series controllers.
Thanks in advance!Cisco does not seem to have an official stencil for the 5508. However I found this link and it seems to have 5508 stencils:
http://www.4shared.com/file/m_dueG18/Cisco-WLC-5508.html -
I need a visio stencil for the 3500XL series switches. I've found the ones offered on the cisco site for 3500 series switches but they are only for the 3550 switches. Can anyone point me in the right direction or happen to have the old 3500XL stencils??
They are similar ... but not the same. I've heard there are older stencils for the 3500XL out there but can't seem to track it down.
-
Cisco Visio Stencils for newer modules
I have been trying to find stencils for 6500 modules released in the last couple of years, and have had very limited success. I need stencils for WS-X6748 modules, WS-X6724 modules, WS-X6848 modules, WS-X6816-2T modules and SUP-2T modules, as well as the NAM3.
If anyone can tell me where these can be found, it will be greatly appreciated.Hi,
Most of what you listed are on the latest Switches-Catalyst 6500 located on the Visio download page:
http://www.cisco.com/en/US/products/hw/prod_cat_visios.html
The WS-X6748 and WS-X6724 modules are not in that file. I will ask the product group if they will approve production of those items.
Regards,
Brett Newman
Cisco Visio Production
Visimation Inc.
www.shapesource.com -
Where are the latest VISIO stencils for logical network device icons
I want to use the same icons commonly used in the Cisco white paper documentation. Where is the stencil for VISIO?
Microsoft provided many Visio Stencils at Visio websites, however, if you want to create your own Visio Stencils you can create it in Visio 2010 in the following way
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin-top:0in;
mso-para-margin-right:0in;
mso-para-margin-bottom:10.0pt;
mso-para-margin-left:0in;
line-height:115%;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
1. On the File menu, point to Shapes, and then click New Stencil.
2. To save the stencil, right-click the stencil title bar, and then click Save.
3. Type a name for your stencil, and then click Save.. -
New Visio Stencils for Catalyst 3750, Telepresence 1300
In response to customer requests, there are new images on the Visio Stencils web page at http://www.cisco.com/en/US/products/hw/prod_cat_visios.html
The updates include images for:
ASA 5510 Rear
ASA 5520 Front
ASA 5520 Rear
ASA 5540 Front
ASA 5540 Rear
ASA 5580 Front
ASA 5580 Rear
ME-C6524GT-8S Front
ME-C6524GT-8S Rear
ME-C6524GS-8S Front
ME-C6524GS-8S Rear
PWR-400W-AC - 400W AC
PWR-400W-DC - 400W DC
Catalyst 3750 Metro Front
Catalyst 3750 Metro Rear
PWR-ME3750-AC
PWR-ME3750-DC
CTS-1300-47
CTS-1300-65Hi Kevin,
We updated the 3750 on 2/23/12 and the CRS on 2/20/12. Please check the download page.
Regards,
Brett Newman
Cisco Visio Development
Visimation Inc.
Maybe you are looking for
-
Hi and Welcome to the Community! With a strong carrier network signal (e.g., not merely WiFi), I suggest the following steps, in order, even if they seem redundant to what you have already tried (step 1 should result in a message coming to your BB...
-
Special characters in passwords
Where can I get documentation for restrictions on passwords. Like what special characters can be used in passwords? Maximum length etc?
-
Firewire 800 enough for burn using dual burners? And what drive to buy?
I have a Mac Pro with a SuperDrive. (I think it's a Pioneer). Tomorrow I'll open the lid and check if the connectors are SATA or IDE. Being either one, I now wonder if I can continue to burn from my external FW800 disc, using the "multiple burner opt
-
How can we create a new terms of payment where installments represent other payment terms. i..e my payment term zzz1 will include 3 installments where each installment represents another existing payment term.
-
Error in Connecting to MS SQL 2005 via JDBC Driver
Here's the setup CF MX7 resides on a centOS wid Apache 2.0 webserver box. I need to established a datasource connection between the Coldfusion server and a MSSQL 2005 Express+SP1 database sitting on a remote XP wid SP2 setup. I've also downloaded and