Vlan Assigment WLC
Dear Friends,
is there any guide or document to make VLAN assigment work, i found only video in youtube that do this using flex connect feature mapping?
thank you
Dynamic VLAN Assignment with RADIUS Server and Wireless LAN Controller Configuration Example
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-vlan/71683-dynamicvlan-config.html
Similar Messages
-
Hello,
Designing a configuration for a Wireless solution. Have a 2951 with SRE-WLC and 4 port switch module. The documentation at
http://www.cisco.com/en/US/docs/wireless/controller/controller_modules/sre/installation/guide/wlcsreinst.html#wp1072942 arised couple of questions. Exact part of diagram from documentation is attached.
The question is that VLANs configured on SRE-WLC and ones configured on local switched belong to different subnets. Why? For example on SRE-WLC VLAN 20 - 55.20.0.0/24, but on switch - VLAN 20 - 20.1.1.0/24. Why?
Thanks!Hi George,
Today i tried implementing APs on different VLAN than MGMT. Here is what I got:
1. New out-of-box APs didnt join to WLC once placed directly to APs VLAN. However they were able to join the WLC once I put them back to MGMT Vlan. They upgraded their IOS from WLC, joined compeletely. After that I moved them back to APs VLAN and they started to join. So, here is the procedure - Open new AP from box, connect it to MGMT VLAN, wait for joining to WLC and then move them to APs VLAN. This is a little bit strange. Also I noticed that they were unable to join teh WLC even on MGMT vlan if MGMT vlan is tagged on WLC and that tagged vlan is allowed on trunk. I have WLC on SRE, MGF trunk, VLANS and DHCP pools with option 43 configured. Will continue to investigate tomorrow.
2. What was the most difficult and problematic issue is that the LED was disabled on all APs after joining the WLC. I have been thinking that there is an error but only then found that APs by default turned off LED after joining the WLC. Issuing config ap led-status enable all on wlc solved the problem.
3. Also I regularly have been receiving
%PARSER-4-BADCFG: Unexpected end of configuration file.
during the AP joining to WLC. Dont know why. My APs are LAP1041n.
ANyways, will continue digging tomorrow, hopefully will find a stable solution. My ideal solution will be:
1. WLC Management is on MGMT VLAN - tagged vlan 20, static IP assignments.
2. APs on separate AP VLAN - tagged vlan 15 - dynamic IP assignments from DHCP pool on ISR with option 43.
3. Clients are on separate USERS VLAN - tagged vlan 10
The native VLAN will be other VLAN - VLAN 25. -
Hi,
In reviewing the lab for WLC configuration, they used a dedicated vlan for all APs and the WLC to communicate with CAPWAP.
In the production environment I'm designing for, a campus network that has many LAN connected sites all with different vlans at the edge, that would entail trunking another vlan out to the edge switches. It also requires the MetroEthernet provider to provision the same beforehand.
One of the advantages of the WLC is the ability to avoid having to add vlans at the edge for WLANs, but what about a dedicated vlan for the APs and WLC to communicate with CAPWAP? A best practice?
Thanks.As best practice we've only two options, keep the AP on L2 vlan(not scalable) of management or on any L3(vlan that is not part of dynamic interface of WLC) which is scalable and good for highavailability.
-
HI,
I went through below link
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008073c723.shtml
I have the same setup except the dhcp.
I have dhcp server which is givng IP to clients; I want to divide clients as bulding 1 and building 2 with vlan
But they should get IP from same dhcp server
how can I do it?Configure it like this
Create AP-Groups in the WLC for each of the building
Create dynamic interfaces for each building
Under WLAN>Ap-Groups, add each AP in each building, in the respective AP-Groups
Map the WLAN to the AP-groups to the interface for each building ( you can see an option, Add interface mapping in the document you sent)
Thanks
NikhiL -
Hi guys,
Let’s say I want to put WLC’s management interface and APs in a separate VLAN than the native/untagged one as Cisco recommends that as a good design practice to use only tagged VLANs on the WLC:
Management Interface VLAN Identifier (0 = untagged): 60
Now on the switchport which connects to the WLC, can I just do the following:
interface GigabitEthernet1/0/1
description Trunk Port to Cisco WLC
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 2-4,60
switchport mode trunk
no shutdown
or I need to add this command as well to make it work? :
switchport trunk native vlan 60
In other word, can I put the management interface in a tagged VLAN but not changing the native/untagged VLAN? The reason that I don’t want to touch native VLAN is that the non-Cisco L3 device in the network doesn’t let me to change its untagged VLAN.
Regards,
Samanf you are setting the wlc vlan to 0 which is untagged, then you need the switchport trunk native vlan 60
If I'm using default untagged 0, then why do I bother changing naive VLAN to 60 on the switch?
where did you get that VLAN 60 from? Am I missing something or you made a typo?
By the way, here is my point of confusion:
Please go to this link . You'll see the following on WLC:
Management Interface VLAN Identifier (0 = untagged): 60
and the following on the switch:
interface GigabitEthernet1/0/1
description Trunk Port to Cisco WLC
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 2-4,60
switchport mode trunk
no shutdown
Now go to this link and you will see this on WLC:
Management Interface VLAN Identifier (0 = untagged): 60
and this on the Switch:
interface GigabitEthernet1/0/1
description Trunk Port to Cisco WLC
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 3-4,60
switchport mode trunk
switchport trunk native vlan 60
no shutdown -
VLAN for WLC interface (ISE Policies Based on SSID)
I have ISE 1.1 and WLC 2504
I used this link http://www.cisco.com/en/US/products/ps11640/products_configuration_example09186a0080bed902.shtml
But I am confuse on the WLC configuration
If I have only one ESSID for corporate user(and many DATA vlan because each AD group is assosiated to one specific VLAN)
I have already created Management interface associated with management Vlan
Wich interface interface should I associate on the corparate WAN ( WLAN -->General --->Interface/interface group) ?
Should I create another interface ? wich Vlan ID should I associate to this interface
or should I use Management interface
Please advisecheck the following links , they are very helpful:
http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a00808c9bd1.shtml
http://www.cisco.com/en/US/products/ps10315/products_configuration_example09186a0080bc8129.shtml
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml
Please make sure to rate correct answers -
I am setting up a 2504. I would like to set up 1 WLAN to connect directly to an ISP switch to use as a PUBLIC network. I configured port 2 on the 2504, set up interface with an address, then created a WLAN and SSID. (Port 1 is set up as internal and connects to the Catalyst 3850) It seems to work. When I change it to different VLAN ID, it does not work. Although port 2 is directly connected to the ISP device, do I have to make any changes on the catalyst for this to work or am I overlooking something. Thanks.
Hi,
Go on below link, it possibly will be helpful for you.
https://supportforums.cisco.com/discussion/11585281/2504-wlc-and-2-vlans -
Dynamic Vlan Assigment on 2950 with acs 4.2
Hello to everyone
We have a problem with Cisco 2950G 48 EI and ACS (version 4.2) providing dynamic Vlan assignment based on groups
On the ACS we configured the following attributes for the specific group
64 = VLAN
65 = 802
81 = VLAN Name
We tried for the 81 attribute both Vlan name and Vlan ID but we get the same results
In detail, we need the machine to be placed on Vlan ID 6 named vlan_sio so we inserted these value in the attribute field
Before we configured the switch to speak with ACS:
aaa new-model
aaa group server radius Switch
server 172.16.0.93 auth-port 1812 acct-port 1813
dot1x system-auth-control
radius-server host 172.16.0.93 auth-port 1812 acct-port 1813 key xxxxxx
radius-server retransmit 3
Configured the ports for the use of dot1.x.
switchport mode access
dot1x port-control auto
dot1x guest-vlan 7
spanning-tree portfast
The users are correctly authenticated but the ports are always connected to the default Vlan of the ports
We tried to debug with the debug dot1.x events command and we get the following errors:
Feb 16 12:00:04.017: Attribute 64 6 0100000D
Feb 16 12:00:04.017: Attribute 65 6 01000006
Feb 16 12:00:04.017: Attribute 81 4 01360806
Feb 16 12:00:04.025: dot1x-ev:Received VLAN is No Vlan
Feb 16 12:00:04.037: dot1x-ev:Received VLAN Id -1
Feb 16 12:00:04.041: dot1x-ev:dot1x_port_authorized: clearing HA table from vlan 1
Feb 16 12:00:04.049: dot1x-ev:dot1x_port_authorized: Added 0006.1bdb.6a09 to HA table on vlan 1
Does anyone know what we could have missed?
Thank’ssolved
It was just missing the command
aaa authorization network default group XXXX -
Restrict Access Vlan with WLC 4402
Folks, I have three SSID configured on WLC and three groups configured on ACS and I need to restrict SSID access based on ACS group.
I tried to use this guide below.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00807669af.shtml
How you can see, this example is aplicable to 802.1x and work out fine with 2 SSIDs that I have but the third SSID don't work because it use the NAC Web login to Auth the user, I needed to fallback because this configuration blocked my NAC Authentication.
Although I have configured NAR just Group2 and Group3, users on Group1 that are Auth with NAC were blocked.
Anyone Know Why this or How can i configure this restriction on WLC and ACS?
thanks a lotHi,
You could be hitting DDTS CSCdu52690.
I will suggest to do an upgrade ACS version 3.0 is old and unsupported.
Thanks, -
Creating "guest" VLAN on WLC 4400, created interface not selectable
Presently have an internal network WLAN (HREAP) setup and running. I'm trying to create a guest Internet-only WLAN referencing this link http://www.cisco.rw/en/US/tech/tk722/tk809/technologies_configuration_example09186a008070ba8f.shtml
Created dynamic interface "corp-26" and verified it was enabled. When I create the Internet-only WLAN... under Interface Name, only "management" appears in the drop down list; "corp-26" doesn't appear.
How do I assign "corp-26" to my Internet-only WLAN?The management & ap-management are for the APs themselves. You will want a seperate vlan/wlan/subnet for your guest ssids altogether.
You can provide dhcp from the controller or from a dedicated server.
if you select override for dhcp under the wlan settings, provide a dhcp server address, otherwise add the dhcp server entries under the interface settings.
What is really cool is that 1.1.1.1 appears as the dhcp server (unless you changed it on the controller to something else.) It has caused some confusion at times -
I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN .
HI All,
I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN . the WLC are providing the HQ and one of the Branches the Wireless services .
Am using all the available 9 SSIDs at the HQ , and am using only 4 of it at the Brnche.
The problem that i have are happening only at the Branch office as i cant room between the SSIDs within Diferent VLANs but i can do it with the one that pointing to the same VLAN. Once the client ( Laptop/Phone ) connected to one of the SSIDs. it imposiible to have him connected to the other ones with Different VLAN. meanwhile, It says its connected to the other SSID but its not getting IP from that pool.
here is the Show Run-Config from my WLC .. and the Problem happening between the SSID AMOBILE and ASTAFF. i have the Debug while am switching between the SSIDs if needed .
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.11.04 10:20:47 =~=~=~=~=~=~=~=~=~=~=~=
show run-config
Press Enter to continue...
System Inventory
NAME: "Chassis" , DESCR: "Cisco 5500 Series Wireless LAN Controller"
PID: AIR-CT5508-K9, VID: V01, SN: FCW1535L01G
Burned-in MAC Address............................ 30:E4:DB:1B:99:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 12
Press Enter to continue or <ctrl-z> to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.235.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
Build Type....................................... DATA + WPS
System Name...................................... WLAN Controller 5508
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 10.125.18.15
Last Reset....................................... Software reset
System Up Time................................... 41 days 5 hrs 14 mins 42 secs
System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada)
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... US - United States
--More or (q)uit current module or <ctrl-z> to abort
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +20 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 10
Number of Active Clients......................... 61
Burned-in MAC Address............................ 30:E4:DB:1B:99:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 12
Press Enter to continue or <ctrl-z> to abort
AP Bundle Information
Primary AP Image Size
ap3g1 5804
ap801 5192
ap802 5232
c1100 3096
c1130 4972
c1140 4992
c1200 3364
c1240 4812
c1250 5512
c1310 3136
c1520 6412
c3201 4324
c602i 3716
Secondary AP Image Size
ap801 4964
c1100 3036
--More or (q)uit current module or <ctrl-z> to abort
c1130 4884
c1140 4492
c1200 3316
c1240 4712
c1250 5064
c1310 3084
c1520 5244
c3201 4264
Press Enter to continue or <ctrl-z> to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Strong Password Check Features:
case-check ...........Enabled
consecutive-check ....Enabled
default-check .......Enabled
username-check ......Enabled
Press Enter to continue or <ctrl-z> to abort
Network Information
RF-Network Name............................. OGR
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
--More or (q)uit current module or <ctrl-z> to abort
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Web Auth Proxy Redirect ................... Disable
Fast SSID Change ........................... Enabled
AP Discovery - NAT IP Only ................. Enabled
IP/MAC Addr Binding Check .................. Enabled
Press Enter to continue or <ctrl-z> to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE SFPType
1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseTX
2 Normal Disa Enable Auto Auto Down Enable N/A Not Present
3 Normal Disa Enable Auto Auto Down Enable N/A Not Present
4 Normal Disa Enable Auto Auto Down Enable N/A Not Present
5 Normal Disa Enable Auto Auto Down Enable N/A Not Present
6 Normal Disa Enable Auto Auto Down Enable N/A Not Present
7 Normal Disa Enable Auto Auto Down Enable N/A Not Present
8 Normal Disa Enable Auto Auto Down Enable N/A Not Present
Press Enter to continue or <ctrl-z> to abort
AP Summary
Number of APs.................................... 8
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KNOWLOGY_DC01 2 AIR-LAP1131AG-A-K9 00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1 US 1
KNOWLOGY_DC02 2 AIR-LAP1131AG-A-K9 00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1 US 1
KN1252_AP01 2 AIR-LAP1252AG-A-K9 00:21:d8:ef:06:50 Knowlogy Confere 1 US 1
KN1252_AP02 2 AIR-LAP1252AG-A-K9 00:22:55:8e:2e:d4 Server Room Side 1 US 1
Anham_AP03 2 AIR-LAP1142N-A-K9 70:81:05:88:15:b5 default location 1 US 1
ANHAM_AP01 2 AIR-LAP1142N-A-K9 70:81:05:b0:e4:62 Small Conference 1 US 1
ANHAM_AP04 2 AIR-LAP1131AG-A-K9 00:1d:45:86:e1:b8 Conference room 1 US 1
ANHAM_AP02 2 AIR-LAP1142N-A-K9 70:81:05:96:7a:49 Copy Room 1 US 1
AP Tcp-Mss-Adjust Info
AP Name TCP State MSS Size
KNOWLOGY_DC01 disabled -
KNOWLOGY_DC02 disabled -
--More or (q)uit current module or <ctrl-z> to abort
KN1252_AP01 disabled -
KN1252_AP02 disabled -
Anham_AP03 disabled -
ANHAM_AP01 disabled -
ANHAM_AP04 disabled -
ANHAM_AP02 disabled -
Press Enter to continue or <ctrl-z> to abort
AP Location
Total Number of AP Groups........................ 3
Site Name........................................ ANHAM8075
Site Description................................. ANHAM 8075 Location
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
9 knowlogy_ogr Disabled None
7 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Anham_AP03 2 AIR-LAP1142N-A-K9 70:81:05:88:15:b5 default location 1 US 1
ANHAM_AP01 2 AIR-LAP1142N-A-K9 70:81:05:b0:e4:62 Small Conference 1 US 1
ANHAM_AP04 2 AIR-LAP1131AG-A-K9 00:1d:45:86:e1:b8 Conference room 1 US 1
ANHAM_AP02 2 AIR-LAP1142N-A-K9 70:81:05:96:7a:49 Copy Room 1 US 1
Site Name........................................ Knowlogy_DC
--More or (q)uit current module or <ctrl-z> to abort
Site Description................................. DC Center Access points
WLAN ID Interface Network Admission Control Radio Policy
2 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
3 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KNOWLOGY_DC01 2 AIR-LAP1131AG-A-K9 00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1 US 1
KNOWLOGY_DC02 2 AIR-LAP1131AG-A-K9 00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1 US 1
Site Name........................................ OGR
Site Description................................. 1934 OGR Office
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
2 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
--More or (q)uit current module or <ctrl-z> to abort
7 knowlogy_ogr Disabled None
9 knowlogy_ogr Disabled None
8 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KN1252_AP01 2 AIR-LAP1252AG-A-K9 00:21:d8:ef:06:50 Knowlogy Confere 1 US 1
KN1252_AP02 2 AIR-LAP1252AG-A-K9 00:22:55:8e:2e:d4 Server Room Side 1 US 1
Site Name........................................ default-group
Site Description................................. <none>
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
2 knowlogy_ogr Disabled None
3 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
5 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
7 knowlogy_ogr Disabled None
8 knowlogy_ogr Disabled None
--More or (q)uit current module or <ctrl-z> to abort
9 knowlogy_ogr Disabled None
10 management Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Press Enter to continue or <ctrl-z> to abort
AP Config
Cisco AP Identifier.............................. 6
Cisco AP Name.................................... KNOWLOGY_DC01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:86:ed:4e
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.100
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................ wireless.knowlogy.com
Primary Cisco Switch IP Address.................. 10.125.18.15
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or <ctrl-z> to abortIP Address.................. 10.125.18.15
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
--More or (q)uit current module or <ctrl-z> to abort
Reset Button..................................... Enabled
AP Serial Number................................. FTX1134T0QG
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 48 days, 20 h 19 m 18 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:33 2013
Join Taken Time.................................. 0 days, 00 h 10 m 47 s
--More or (q)uit current module or <ctrl-z> to abort
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211b
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:71:09:8f:90
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
--More or (q)uit current module or <ctrl-z> to abort
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
--More or (q)uit current module or <ctrl-z> to abort
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 11
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
--More or (q)uit current module or <ctrl-z> to abort
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 6
Cisco AP Name.................................... KNOWLOGY_DC01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:86:ed:4e
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.100
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
--More or (q)uit current module or <ctrl-z> to abort
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................ wireless.knowlogy.com
Primary Cisco Switch Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
--More or (q)uit current module or <ctrl-z> to abort
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
AP Serial Number................................. FTX1134T0QG
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or <ctrl-z> to abort
AP Up Time....................................... 48 days, 20 h 19 m 18 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:33 2013
Join Taken Time.................................. 0 days, 00 h 10 m 47 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:71:09:8f:90
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 20
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or <ctrl-z> to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 15 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 44
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140,
......................................... 149,153,157,161
TI Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
--More or (q)uit current module or <ctrl-z> to abort
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Press Enter to continue or <ctrl-z> to abort
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... KNOWLOGY_DC02
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:36:c5:c4
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.101
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
--More or (q)uit current module or <ctrl-z> to abort
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
--More or (q)uit current module or <ctrl-z> to abort
AP Serial Number................................. FTX1230T24F
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 48 days, 20 h 24 m 41 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:35 2013
Join Taken Time.................................. 0 days, 00 h 10 m 48 s
--More or (q)uit current module or <ctrl-z> to abort
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211b
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:a5:0c:30
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
--More or (q)uit current module or <ctrl-z> to abort
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
--More or (q)uit current module or <ctrl-z> to abort
Current Tx Power Level .................... 1
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
--More or (q)uit current module or <ctrl-z> to abort
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... KNOWLOGY_DC02
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:36:c5:c4
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.101
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
--More or (q)uit current module or <ctrl-z> to abort
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
--More or (q)uit current module or <ctrl-z> to abort
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
AP Serial Number................................. FTX1230T24F
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or <ctrl-z> to abort
AP Up Time....................................... 48 days, 20 h 24 m 41 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:35 2013
Join Taken Time.................................. 0 days, 00 h 10 m 48 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:a5:0c:30
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 20
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or <ctrl-z> to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 15 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140,
......................................... 149,153,157,161
TI Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
--More or (q)uit current module or <ctrl-z> to abort
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Press Enter to continue or <ctrl-z> to abort
Cisco AP Identifier.............................. 5
Cisco AP Name.................................... KN1252_AP01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:ef:06:50
IP Address Configuration......................... DHCP
IP Address....................................... 10.125.18.101
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 10.125.18.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Enabled
Ssh State........................................ Disabled
Cisco AP Location................................ Knowlogy Conference Rooms Side
Cisco AP Group Name.............................. OGR
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or <ctrl-z> to abort
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.4.10.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. PoE/Medium Power (15.4 W)
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1252AG-A-K9
AP Image......................................... C1250-K9W8-M
IOS Version...................................... 12.4(23c)JA5
--More or (q)uit current module or <ctrl-z> to abort
Reset Button..................................... Enabled
AP Serial Number................................. FTX122990L5
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 118
WLAN 1 :........................................ 111
WLAN 2 :........................................ 111
WLAN 4 :........................................ 112
WLAN 6 :........................................ 112
WLAN 7 :........................................ 111
WLAN 9 :........................................ 112
WLAN 8 :........................................ 112
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 26 days, 00 h 24 m 39 s
--More or (q)uit current module or <ctrl-z> to abort
AP LWAPP Up Time................................. 26 days, 00 h 23 m 48 s
Join Date and Time............................... Wed Oct 9 10:59:07 2013
Join Taken Time.................................. 0 days, 00 h 00 m 50 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 7
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:df:a5:90
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
11000 Kilo Bits.......................... MANDATORY
MCS Set
MCS 0.................................... SUPPORTED
MCS 1.................................... SUPPORTED
MCS 2.................................... SUPPORTED
MCS 3.................................... SUPPORTED
MCS 4.................................... SUPPORTED
MCS 5.................................... SUPPORTED
MCS 6.................................... SUPPORTED
MCS 7.................................... SUPPORTED
MCS 8.................................... SUPPORTED
MCS 9.................................... SUPPORTED
MCS 10................................... SUPPORTED
MCS 11................................... SUPPORTED
MCS 12................................... SUPPORTED
MCS 13................................... SUPPORTED
MCS 14................................... SUPPORTED
MCS 15................................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
--More or (q)uit current module or <ctrl-z> to abort
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 ..........Well you need to understand the behavior of h-reap or what it's called now, FlexConnect. In this mode, the clients are still remembers on the WLC until the session timer/idle timer expires. So switching between SSID's in h-reap will not be the same when switching when the AP's are in local mode.
Take a look at the client when connected in FlexConnect in the WLC GUI monitor tab. Thus will show you what ssid and vlan the client is on. Now switch to a different ssid and compare this. It's probably the same because the client has not timed out. Now go back to the other ssid and look again. Now on the WLC, remove or delete the client and then switch to the other ssid at the same time. Or switch SSID's and then remove the client. The client will join the new ssid and in the monitor tab, you should see the info.
There is no need to have clients have multiple SSID's unless your testing. Devices should only have one ssid profile configured to eliminate any connectivity issues from the device wanting to switch SSID's.
Sent from Cisco Technical Support iPhone App -
WLC, FlexConnect, ISE: Dynamic VLAN not working
Hi,
Not sure if this is a WLC or ISE problem, but since I am unsure of the WLC config I will try here first.
Equipment:
WiSM2 7.2.111.3
ISE 1.1.1.268
AP 3502 in FlexConnect
What I want to achive:
One SSID, multiple VLAN
Devices gets profiled in ISE and based on type of device it gets asigned to a VLAN
Problem:
When the device connects the first time it ends up in native VLAN and not switched to the right VLAN, but when I reconnect then it is added to the right VLAN.
WLC config (I know you like images so here you go ):
I must be missing something but I can't figure out what. I will be attaching a debug aaa event enable for when the client connect the first time.
In ISE I have an Authorization Profile that just say VLAN ID/Tag 158 (the VLAN that the device should go to) an it is added to the Authorization rule of the profiled device. CoA is set to Reauth.
When the client connects I get three events in ISE:
1.
Authentication failed :
22056 Subject not found in the applicable identity store(s)
2. Authentication Success. With the results:
UserName=00:18:DE:A2:BC:3A
User-Name=00-18-DE-A2-BC-3A
State=ReauthSession:c20e8b2f0000027e50ed27f8
Class=CACS:c20e8b2f0000027e50ed27f8:ISE01/144259326/671335
Termination-Action=RADIUS-Request
Tunnel-Type=(tag=1) VLAN
Tunnel-Medium-Type=(tag=1) 802
Tunnel-Private-Group-ID=(tag=1) 158
cisco-av-pair=profile-name=AX-Intel-Device
3.
Dynamic Authorization failed :
11213 No response received from Network Access Device
Has anyone got this to work? Do I need to add FlexConnect groups? If so then why?
Regards,
PhilipI think you're hitting CSCua58554
The bugtoolkit description is horrible.... From what I recall when I ran into it, I believe that Flex connect is having a problem with Mac filtering based AAA override on open wlans (and/or CWA based). In general, AAA override works fine when it is from like an eap authentication.
We had to use a 7.3 ES to resolve it.....
Looks like it is implemented in 7.4 though..... If you dont want to join the 7.4 bandwagon quite yet, you might could ask TAC for an ES of 7.3, don't think they have a 7.2 build. -
WLC- dynamic Vlan assignment with Radius
Hello, we would like to use this feature in our company and because of that I am now testing it. But I found one problem.
I created one testing SSID and two Vlans on WLC. On ACS I use an IETF atributes (064,065,081) for my account and I am changing Vlan ID (081) during testing.
It works with LEAP but when I use PEAP-GTC (which we use commonly in our company) the ip address is not assigned properly (ip which was assigned before remains).
Could you please help me?There is good document which explains how to configure Dynamic VLAN Assignment with RADIUS Server and Wireless LAN Controller. This will help you. You will find the document at http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml
-
Hello
I have WLC connect to MLS and 30 AP connect to Access SW, my question is the best practice is to put WLC in separate vlan [means this vlan have two IP only, one for WLC and another for SVI], and separate vlan to AP?
Also should to be AP Manager IP for WLC in same vlan for WLC or AP VLAN?
Thanks in advanced...AP manager interface required only in 44xx, WiSM1 (old hardware). In these platforms ap manager & management interface should be on the same vlan.
5508/2504/etc you only required the management interface.
AP vlan does not have any relation to those. So it can be completely different vlan. If it is a small deployment you can put AP on the same vlan as wlc management. Then AP will discover WLC using L3 broadcast. If you put AP on different vlan to wlc management, you have to use WLC discovery method (like DHCP option 43, DNS, etc) for AP to find the WLC.
HTH
Rasika
**** Pls rate all useful responses **** -
Wlc management port can't trunk other than native vlan
Hello,
Ihave installed my first WLC 5508 with this topology :
WLC Connected trought distrubtion SFP 1Gb port to Core Switch port configured as Trunk port permetting 3 Wireless VLAN :
- Management WLC, Wireless Voice and Wireless Data Vlan (native Vlan is management WLAN).
- I have created 2 dynamic interface on WLC regarding my Wireless VLAN :
10.7.1.0/24 : Defaut Management Virtual Interface when installing WLC +
10.7.6.0/24 : Voice Virtual Interface and
10.7.2.0/24 : Wireless Data Virtual Interface trought GUI.
DHCP configured on each dynamic interface is the L3 vlan interface for equal VLAN subent for CORE SWITCH contining IP DHCP Pool.
WLC Management Inerface IP adress is : 10.7.1.10/24
I Have create 2 WLAN with SSID named Data ID 1 & Voice ID2.
I have create and AP Groupe named APGRP1 containing the AP registered on WLC and using both SSID WLAN.
Both AP are connected to Switch acess port configured as access port to native management WLC VLAN.
I have create 3 IP DHCP pool on Core switch with related L3 Interfaces for Inter VLAN routing.
Problem: when I try to connect from laptop to Data SSID I get IP Address from management WLC VLAN a non DATA VLAN.
the same case from Wireless IP Phone configured with Voice SSID.
What can I modifie that permet to both device to get IP address from the correct VLAN?
ThnksHi Adil,
Q1 >> AP access port on the switch must be configured on an Access port mode or trunk mode?
ANS - The LWAPP/ CAPWAP APs connected to the switchport should be a Access port not trunk.
Q2>> if the first case, setting the port on, the same VLAN like WLC Management VLAN will support other WLAN Vlans (voice and data)?
ANS - Yes it does support, since the traffic which involes the WLAN will be inside the LWAPP/CAPWAP logical tunnel.
Q3>> I will verify the interface mapping between WLAN and Dynamic Interfaces and i will tell you.
ANS - I will be waiting for your response!!
lemme know if this answered your question..
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull
Maybe you are looking for
-
I purchased Lion 10.7 on Christmas Day, I received my redemption code a week later. I've tried to download Lion to no avail. I've been in contact with Apple Support and they haven't been much help so far. My computer is currently running Snow Leopart
-
I guess this all goes back to me wanting to sync my photos from my phone to my computer. In iTunes I don't have the option to sync from my phone to the computer. I just have the ability to sync from Computer to the Phone. Thanks in advance
-
Acrobat 9.5.5 multiple .pdf files open without toolbars displaying
Recently, I noticed that, when I open one .pdf file, all toolbars I have selected as customized are displayed. But, upon opening additional ,pdf files, those files do not display my toolbars at the top - only the file menu shows up. If I try to clo
-
Illustrator CS4 will not open in XP Professional
Hello, Although I am running Windows XP Professional AI CS4 will not open on my computer. Photoshop and InDesign work perfectly but Illustrator seems unable to recognize the XP operating system and gives an error message accordingly. Please see the a
-
I was working on a document doing Track Changes when Microsoft Word crashed. Word recovered my document and I began working on that document doing Track Changes. I saved it several times, hitting "replace." I then exited out when I finished. I cannot