VLAN assignment without ACS on Cisco Wireless Controller 5508
I was wondering if it is possible to do dynamic VLAN assignment on the Cisco Wireless Controller 5508 without using Cisco ACS but use Microsoft NPS server instead? Is there a manual or article that someone can point me in the right direction?
Thank you!
Any RADIUS server will allow you to do the dynamic vlan assignment if you configure the right RADIUS attributes (64, 65 and 81 that Steve mentioned above).
This doc shows example of dynamic vlan assignment with WLC and ACS.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml
Same config on WLC is needed. However, on the RADIUS you need to configure the same attributes on the NPS instead.
HTH
Amjad
Rating useful replies is more useful than saying "Thank you"
Similar Messages
-
802.1x dynamic vlan assignment using ACS 4.2
Hi
we have 10 switches 2960 configured with 802.1x authentication against ACS server 4.2.
we have 2 vlans configured on the switches for administrator and endusers. the end user vlan id is 10 and the administartor vlan is is 100.
we need to apply the following scenario, if the enduser PC - that is connected to vlan 10 - has an issue and the administrator will login to the PC with the administrator account to fix that issue, the switch should dynamically reconfigure the port with the administrator vlan ( 100 ) .
is the above scenario doable using dot1x with the ACS server?
waiting your replies
MohamedHi,
I have the following scenario
2 bulidings with multiple floor
Each floor should be in different VLAN.
The network should be authenticated with 802.1x and each switch port should be assigned with dynamic VLAN from ACS.
Each
user should be able to connect and roam around between any building.
when ever a user is connecting his laptop to any floor, he should be
made part of that respective vlan. It is not requred to have the same
IP rage to be allocated, but the dynamic VLAN should be based on the
switch port location.
Can
I configure ACS in such a way that, the ACS will allocate dynamic VLAN
for every 802.1x authentication based on the Network Device Group.
Please refer the attached diagram
Hi,
Check out the below link for your requirement for dynamic vlan assignement using ACS
http://www.ciscosystems.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml
Hope to Help !!
Ganesh.H
Remember to rate the helpful post -
802.1x Dynamic Vlan assignment using ACS
Hi,
I have the following scenario
2 bulidings with multiple floor
Each floor should be in different VLAN.
The network should be authenticated with 802.1x and each switch port should be assigned with dynamic VLAN from ACS.
Each user should be able to connect and roam around between any building. when ever a user is connecting his laptop to any floor, he should be made part of that respective vlan. It is not requred to have the same IP rage to be allocated, but the dynamic VLAN should be based on the switch port location.
Can I configure ACS in such a way that, the ACS will allocate dynamic VLAN for every 802.1x authentication based on the Network Device Group. Please refer the attached diagramHi,
I have the following scenario
2 bulidings with multiple floor
Each floor should be in different VLAN.
The network should be authenticated with 802.1x and each switch port should be assigned with dynamic VLAN from ACS.
Each
user should be able to connect and roam around between any building.
when ever a user is connecting his laptop to any floor, he should be
made part of that respective vlan. It is not requred to have the same
IP rage to be allocated, but the dynamic VLAN should be based on the
switch port location.
Can
I configure ACS in such a way that, the ACS will allocate dynamic VLAN
for every 802.1x authentication based on the Network Device Group.
Please refer the attached diagram
Hi,
Check out the below link for your requirement for dynamic vlan assignement using ACS
http://www.ciscosystems.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml
Hope to Help !!
Ganesh.H
Remember to rate the helpful post -
Cisco wireless controller 4400
Hey all,
I was wondering does the Cisco Wireless controller 4400 come with any management software such as the Cisco Wireless Controller system software?
regards,
MarkWCS doesn't come with your WLC purchase you can down load a trial version of WCS from Cisco site. I think it is a 15 or 30 day trial.
You would have to purchase a license to run a full blown WCS. You can get this in either Linux or Windows.
Hope this helps you.
You can find info on this at:
http://www.cisco.com/en/US/prod/collateral/wireless/ps5755/ps6301/ps6305/product_data_sheet0900aecd804b4646_ps3915_Products_Data_Sheet.html -
Clients are unable to access a New wireless Controller 5508
Clients are unable to access the public ssid, which is wide open(or any other ssids).
I'm using LAG and I can ping each interface on the controller. Ap's show a total of 2 and 2 are up.
interface name is public vlan identifier 107, ip add 10.1.255.252, interface dynamic
Software version 7.0.98.0
Model No.
AIR-CT5508-K9
Burned-in MAC Address
50:3D:E5:1A:2F:60
Maximum number of APs supported
25
FIPS Prerequisite Mode
Disable
UDI :
Product Identifier Description
AIR-CT5508-K9
Version Identifier Description
V01
Serial Number
FCW1508L0KT
Entity Name
Chassis
Entity Description
Cisco Wireless Controller
Profile Name
Type
SSID
Status
Enabled
Security Policies
(Modifications done under security tab will appear after applying the changes.)
Radio Policy
All 802.11a only 802.11a/g only 802.11g only 802.11b/g only
Interface
jmhmanagementpublicspacelabsvoice
Broadcast SSID
Enabled
Layer 2 security none
Below is the errors that are in the controller's log.
spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-DECODE_ERR: spam_lrad.c:1932 Error decoding join request from AP 00:00:00:00:00:00
*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-JOIN_DB_ERR: spam_lrad.c:6216 Could not allocate an entry in the database for AP 00:00:00:00:00:00 - dropping the join request (# of APs joined = 2)
*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-AP_DB_CREATE_ERR: spam_lrad.c:4945 Unable to create an entry for AP 00:00:00:00:00:00 in the database - invalid mac address
*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-PAYLOAD_MISSING: spam_lrad.c:5400 Join request does not contain BOARD_DATA payload
*spamApTask0: Dec 06 14:54:24.728: %LWAPP-3-DECODE_ERR: spam_lrad.c:1932 Error decoding join request from AP 00:00:00:00:00:00
*spamApTask0: Dec 06 14:54:24.728: %LWAPP-3-JOIN_DB_ERR: spam_lrad.c:6216 Could not allocate an entry in the database for AP spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-DECODE_ERR: spam_lrad.c:1932 Error decoding join request from AP 00:00:00:00:00:00
*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-JOIN_DB_ERR: spam_lrad.c:6216 Could not allocate an entry in the database for AP 00:00:00:00:00:00 - dropping the join request (# of APs joined = 2)
*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-AP_DB_CREATE_ERR: spam_lrad.c:4945 Unable to create an entry for AP 00:00:00:00:00:00 in the database - invalid mac address
*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-PAYLOAD_MISSING: spam_lrad.c:5400 Join request does not contain BOARD_DATA payload
*spamApTask0: Dec 06 14:54:24.728: %LWAPP-3-DECODE_ERR: spam_lrad.c:1932 Error decoding join request from AP 00:00:00:00:00:00
*spamApTask0: Dec 06 14:54:24.728: %LWAPP-3-JOIN_DB_ERR: spam_lrad.c:6216 Could not allocate an entry in the database for AP
I have attached show run-config and show running-configFor the public WLAN, what is 10.1.1.1? Is it a real DHCP server, is it a FW? If it's a FW, then you'll need to disable dhcp proxy:
CLI config dhcp proxy disable
GUI Controller > Advanced > DHCp, and uncheck the box for proxy.
As for all of your other SSID, they are all pointd at the management interface. Double check the WLAN config, and point them to the interface you want the user to get an IP address in.
HTH,
Steve
Please remember to rate helpful posts or to mark the question as answered so that it can be found later. -
Multiple Wireless Controller 5508 in WCS 7.0
I have two Wireless Controller 5508 that are IDENTICAL in configurations and they will work as an ACTIVE/STANDBY scenario because right now we only have 30 APs, which one of the controller should be fine dealing with them...
Now, the way we used to work was everytime we had to add a new WLAN, or change an ACL, etc..we had to both controllers and do the exact same things, so both would be ready in case of a failure of the MAIN controller....so in order to avoid this extra work, we bought the WCS 7.0, thinking we would only have to do it once, and the WCS would update both WLC...but I cant find that option..Ive read all the configuration guide, and cant find a way to keep this two controller completaly sync......I read something about templates..but I still have to do "extra" work in order to keep them sync..
How do you guys keep your WLC sync??
THanks!Carlos, make sure you also look at config groups. When you place a template into a config group and if you enable the background task for nightly configuration audits you do get a tally of which controllers are "in sync" and which ones are not. Cisco does not automatically apply any configurations from WCS/NCS to controllers, nor would I ever want them to in all honesty.
NCS is a nice product and has a lot in the roadmap that will hopefully add more value to having your switches loaded. I can see in the future being able to have port templates for voice, data, etc, and then applying those to switch ports at a help desk tech level, they don't need to know how to configure the port, they just need to select a port and then a template. -
VLAN assignment from ACS not applied
WLC 4402 5.2.157.0
ACS Express 5.0.0.18
We have an issue where the VLAN assigned on the ACS isn't applied on the 4402 WLC.
We have 'Allow AAA Override' checked on the WLAN, the QoS is overridden to bronze properly, but the VLAN stays at 0 and the interface at management. The VLAN interface is configured on the WLC.
On the ACS the following are configured for the RADIUS response:
Radius-IETF Tunnel-Medium-Type 802
Radius-IETF Tunnel-Type VLAN
Radius-IETF Tunnel-Private-Group-ID 44
Cisco Airespace Airespace-QoS-Level Bronze
The accounting log shows:
Wed, 04 Feb 2009 09:50:02
User-Name = guest
NAS-IP-Address = 10.30.1.2
NAS-Port = 1
Framed-IP-Address = 10.30.1.12
Called-Station-Id = 10.30.1.2
Calling-Station-Id = 10.30.1.12
NAS-Identifier = Cisco4402WLC
Acct-Status-Type = Start
Acct-Session-Id = 4989b927/00:1a:73:ed:bf:ca/2
Acct-Authentic = RADIUS
Airespace-WLAN-Id = 2
Thanks for any help or advice you can provide to troubleshoot this issue.
-BrianFrom the Clients -> Details screen on the WLC...
CLIENT PROPERTIES
MAC Address 00:1a:73:ed:bf:ca
IP Address 10.30.1.12
Client Type Regular
User Name guest
Port Number 1
Interface management
VLAN ID 0
CCX Version CCXv4
E2E Version Not Supported
Mobility Role Local
Mobility Peer IP Address N/A
Policy Manager State RUN
Mirror Mode Disable
Management Frame Protection No
SECURITY INFORMATION
Security Policy Completed Yes
Policy Type N/A
Encryption Cipher None
EAP Type N/A
NAC State Access
QUALITY OF SERVICE PROPERTIES
WMM State Enabled
U-APSD Support Disabled
QoS Level Bronze
Diff Serv Code Point (DSCP) disabled
802.1p Tag disabled
Average Data Rate disabled
Average Real-Time Rate disabled
Burst Data Rate disabled
Burst Real-Time Rate disabled -
VLAN Assignment of SSID using Cisco AV Pair or Dot1x ?
Hi.
I am looking to setup wireless access to 2 of my internal VLANs. I am using Cisco 1130AG, PEAP and RADIUS for the authentication as one network is for employees only and one restricted to guests only.
I was wondering which was the most recommended solution.
1. To have 2 SSIDs, with one in each VLAN with the access restricted using the Cisco AV Pair attribute in RADIUS
or
2. Use one SSID and use Dot1x and the Tunnel attribute to assign the VLAN?
This option I feel is more complicated and I am still unsure how this works in reality as the SSID itself can only be part of one VLAN????
Do I have to configure a Dot11Radio and Fastethernet interface for each intended vlan in this case?
Could someone please explain and suggest their preferred option.
Thanks.You should have two ssid's one for your internal and one for guest. You should use 802.1x for your internal and your guest should be open with a Login page of some sort. You can still use dynamic vlan assignments so that your internal users who try to access the guest page will be put on the internal vlan. Of course the guest will always be placed on the guest vlan. If you have a WLC, the login page and setup is easier, because in autonomous you will have to use something like ZoneCD for guest if you want a HotSpot type wifi.
-
Syslog on Cisco Wireless Controller
Hi everyone
I have question about syslog on wireless controller. I need to know what is information in the syslog from controller. I had read paper in the community some siad it has not much in the syslog but it has not detial what is the information in the syslog sent. I know that almost information such as client, authentication, and much benefit logging in the SNMP. So, anyone have any idea or information please give me the idea or information.
Thanks
VYou just need to setup the sylog and try different logging levels to see if it gives you the information you need. YOu might not get what you want or if you find a syslog level that gives you the info you want, you might get a lot of stuff you don't want to see.
http://www.cisco.com/en/US/products/ps6307/products_configuration_example09186a00809a2d76.shtml
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered" -
How i configure cisco wireless controller
how i can confiure cisco wireless controller
Cisco Wireless LAN Controller Configuration Guide, Release 7.0:
http://www.cisco.com/c/en/us/td/docs/wireless/controller/7-0/configuration/guide/c70.html -
Cisco Wireless controller CT 5760
Does this above mentioned Wireless controller support :
•- Port Based Access Control
•- What is the Switching capacity speed
•- What is the MAC Address table size
Regards,
DravvyHello,
May the link below help you out:-
http://www.cisco.com/en/US/prod/collateral/wireless/ps6302/ps8322/ps12598/data_sheet_c78-722607.html -
Save config of Wireless Controller 5508 by SNMP
On Catalyst switches one can save the running config with SNMP by using the CISCO-CONFIG-COPY-MIB.
Is there an equivalent way of doing this on a 5508 Wireless Controller ?
Many thanks
chrisIs it Cisco best practices to create one large Vlan that contains both controllers, ap's and clients all in the same network ? Or should I be segmenting the network a particular way?
Not best practice. Segmentation is up to how you want to do it for the most part
With my current Wireless Controllers is it possible to segment the wireless network by building into seperate networks (vlans) but still allow clients to connect to the (mmg_wireless) ssid and roam throughout the campus without mobility and roaming issues?
yes, you could use AP groups and do a subnet per building. the traffic will still backhaul to the WLC then to the core. So if the latency is the fiber between the buildings you would still have an issue. you could also use FlexConnect, but would need to know more on how the application is supposed to work to answer that better
Is it necessary to segment my wireless network by creating more vlans instead of putting all of the ap's controllers and clients all in the same network? Will having all of my wireless devices in the same subnet degrade my wireless network because everything is in the same broadcast domain?
IMHO, I think the AP should be in their own VLAN, and the WLC can live in the 'server' vlan if you want.
Is there a maximum recommended number of ap's that should be on a controller at any given moment? I currently have 200 ap's on one controller.
with 672 clients currently conencted to them. (360 of them are connected to the mmg_wireless ssid) .
how many ports are you using to connect to teh 6509? if you are using all 8 ports you should be fine.
Is it best practice to seperate the maangement ip's of the controllers and ap's from the client vlans?
answered above -
Wireless Controller 5508 dropping MAC Addresses
Our 5508 Wireless Controller will drop MAC addresses clean out of the system. Addresses that are in use everyday just disappear. It is not a limitation issue because we are adding iPads everyday. And it is not a daily occurance, but maybe once or twice a week. Has anyone come accross this issue? Everything has been updated and it is more of a hassle than anything, I am just trying to understand what is happening.
Shannon,
can you be a bit more specific, when you say it's dropping mac addresses?
is that from the user list? the macfilter? -
Cisco wireless controller and AP-binding domain how do you integrate wireless domain authentication?
With Cisco equipment wlc 2500 and AP 1600 combines windows 2008 r2 domain controller to achieve the following purposes,
1, all cell phones and laptops can access the wireless network with a domain user authentication.
2, the guest network should how to do it?
My idea is:
Made a total of two ssid below
Mobile users cnnewcity_mobile: Use webportal certification, so the center certification, local forwarding
Computer users cnnewcity_wifi: transparent certification, local forwarding, local authentication
The basic steps are as follows:
1, set the Radius server clients (AP or controller)
2, locking authorization group --- this should be based on the domain user group authorization radius server
3, the mobile roaming - different locations on the DHCP server choose to do this you have to consider the next 43
4, the establishment of a two vlan to a mobile user to the computer user, create a DCHP scope on the DHCP
I do not know if you have wood there are better ways?Integrating the AD to the WLC Requires:
1. AD to be registered:
AT: Security->AAA
AT: LDAP
CLICK: New
Server IP: <AD IP>
Port Number: 389
Simple Bind: Authenticated
Bind User: CN=Administrator,CN=Users,DC=testing,DC=local,DC=com
Bind Pass: <LDAP Admin pass>
Confirm Pass: <LDAP Admin pass>
User Base DN: OU=WebAuth_Users,DC=testing,DC=local,DC=com
User Attrib: sAMAccountName
User Obj. Type: person
Enable at WLAN Profile
1. AT: WLAN->WLANs
CLICK: <Desired WLAN> -typically web authentication
2. AT: Security Tab
AT: AAA Servers
3. AT: LDAP Servers
**Select Created LDAP
4. Apply to Save
Source: Tried it in implementations :)) -
Wireless Network is slow after putting cisco wireless controller
Hello Guys,
My wireless network was very good before putting Cisco WLC 4402 with version 3.2.171.6.
In my network there are two SSID's one for official and another for guest, which is working one single LAP 1142.( Total 12 LWAP is here)
we decided to manage all the ap and deployed WLC but now wireless network is very slow, local gateways is pinging with 80 ms. before WLC it was 1 ms.
Pls. suggest or come up with question to reach a solution.
reg
sanjeevHi,
yah it's gigabit support and i have connected with fibre patch cord.
My SWITCH port config is below.
interface GigabitEthernet1/0/25
switchport trunk encapsulation dot1q
switchport mode trunk
Controller sh run
System Inventory
Switch Description............................... Cisco Controller
Machine Model.................................... AIR-WLC4402-12-K9
Serial Number.................................... FOC1105F01E
Burned-in MAC Address............................ 00:1A:6D:DD:23:00
Crypto Accelerator 1............................. Absent
Crypto Accelerator 2............................. Absent
Power Supply 1................................... Absent
Power Supply 2................................... Present, OK
Press Enter to continue Or to abort
System Information
Manufacturer's Name.............................. Cisco Systems, Inc
Product Name..................................... Cisco Controller
Product Version.................................. 3.2.171.6
RTOS Version..................................... 3.2.171.6
Bootloader Version............................... 3.2.171.6
Build Type....................................... DATA + WPS
System Name...................................... SFA-CTRL2-HQ
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.14179.1.1.4.3
IP Address....................................... 10.156.11.231
System Up Time................................... 0 days 11 hrs 9 mins 43 secs
Configured Country............................... United States
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +38 C
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 4
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 115
Press Enter to continue Or to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
Current LWAPP Transport Mode..................... Layer 3
LWAPP Transport Mode after next switch reboot.... Layer 3
FIPS prerequisite features....................... Disabled
Press Enter to continue Or to abort
Network Information
RF-Network Name............................. UNISFA
Web Mode.................................... Enable
Secure Web Mode............................. Enable
Secure Shell (ssh).......................... Enable
Telnet...................................... Enable
Ethernet Multicast Mode..................... Disable Mode: Ucast
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
ARP Unicast Mode............................ Disabled
Cisco AP Default Master..................... Disable
Mgmt Via Wireless Interface................. Enable
Bridge AP Zero Config....................... Enable
Bridge Shared Secret........................ youshouldsetme
Allow Old Bridging Aps To Authenticate...... Enable
Over The Air Provisioning of AP's........... Enable
Mobile Peer to Peer Blocking................ Disable
Apple Talk ................................. Disable
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Fast SSID Change ........................... Disabled
Press Enter to continue Or to abort
Port Summary
STP Admin Physical Physical Link Link Mcast
Pr Type Stat Mode Mode Status Status Trap Appliance POE
1 Normal Forw Enable Auto 1000 Full Up Enable Enable N/A
2 Normal Disa Enable Auto 1000 Full Down Enable Enable N/A
Press Enter to continue Or to abort
AP Summary
AP Name Slots AP Model Ethernet MAC Location Port
AP_MHQ_CMS_OFFICE 2 AIR-LAP1242AG-A-K9 00:19:30:76:75:42 default location 1
AP01-MHQ-HOM 2 AIR-LAP1242AG-A-K9 00:19:30:76:74:be default location 1
AP01_MHQ_AIROPS 2 AIR-LAP1242AG-A-K9 00:1d:45:36:6c:84 default location 1
AP01_MSA_HOM_RES 2 AIR-LAP1242AG-A-K9 00:1d:45:36:6b:e2 default location 1
AP10-MHQ-CCITS 2 AIR-LAP1242AG-A-K9 00:19:30:76:74:82 default location 1
AP01-MSA2-TC5 2 AIR-LAP1242AG-A-K9 00:1d:45:36:6d:44 default location 1
AP01_MSA_CableTV_Room 2 AIR-LAP1242AG-A-K9 00:19:30:76:83:aa default location 1
AP01_MSA_RUS_ROOM 2 AIR-LAP1242AG-A-K9 00:19:30:76:83:00 default location 1
AP01-MHQ-JLOC 2 AIR-LAP1242AG-A-K9 00:19:30:76:7f:d0 default location 1
AP01-MSA-C2-D 2 AIR-LAP1242AG-A-K9 00:19:30:76:74:90 default location 1
AP01_MSA_DA7 2 AIR-LAP1242AG-A-K9 00:19:30:76:80:38 default location 1
AP01_MSA_CMS_RES 2 AIR-LAP1242AG-A-K9 00:19:30:76:83:f0 default location 1
Press Enter to continue Or to abort
AP Config
Cisco AP Identifier.............................. 1
Cisco AP Name.................................... AP_MHQ_CMS_OFFICE
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:75:42
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.240
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1107B3U8
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211g
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1a:a2:d9:d3:60
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 1
Cisco AP Name.................................... AP_MHQ_CMS_OFFICE
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:75:42
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.240
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1107B3U8
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1a:a2:d9:d3:60
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
9000 Kilo Bits........................... MANDATORY
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 15 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 24
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 2
Cisco AP Name.................................... AP01-MHQ-HOM
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:74:be
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.238
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1107B3W4
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211g
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1a:30:e7:fc:30
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 2
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 11
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. Side A or Right Connector
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 2
Cisco AP Name.................................... AP01-MHQ-HOM
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:74:be
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.238
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1107B3W4
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1a:30:e7:fc:30
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
9000 Kilo Bits........................... MANDATORY
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 15 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... AP01_MHQ_AIROPS
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:36:6c:84
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.232
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1135B2X7
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211g
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:46:7e:d9:60
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 6
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. Side A or Right Connector
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... AP01_MHQ_AIROPS
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:36:6c:84
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.232
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1135B2X7
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:46:7e:d9:60
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
9000 Kilo Bits........................... MANDATORY
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 15 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 4
Cisco AP Name.................................... AP01_MSA_HOM_RES
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:36:6b:e2
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.239
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1135B2X1
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211g
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:46:7e:d4:30
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 11
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 4
Cisco AP Name.................................... AP01_MSA_HOM_RES
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:36:6b:e2
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.239
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1135B2X1
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:46:7e:d4:30
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
9000 Kilo Bits........................... MANDATORY
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 15 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 149
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 5
Cisco AP Name.................................... AP10-MHQ-CCITS
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:74:82
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.233
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1107B3TJ
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211g
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1a:30:e7:fa:60
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 5
Cisco AP Name.................................... AP10-MHQ-CCITS
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:74:82
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.233
IP NetMask.........
Maybe you are looking for
-
IT0185 Field value is not getting displayed on the Payslip
Hi Friends, I have the similar issue of this post as Unable to View the IT0185 Subtype National Ins# (ICNUM) in Payslip. Little confused with PE51_CheckTab entries and other stuff. Could anybody please suggest as to how to resolve this? thanks in adv
-
Is there a way to use the 'search' function outside the search menu
Is it possible, to activate the 'search function' outside the 'search menu' on the iPod classic ? With 30000 songs and more on an iPod, it would be great, if I could use this option i.e. in cover flow, display songs, or display albums. This way, I wo
-
URGENT: Problem in printing Character Mode Report in Chinese Version
Hello, I am working with Reports 6i. i have developed one Character mode report. This report is working and printing fine in Windows 2000 Server (English Version). But, this report is not working properly in Windows 2000 Professional (Traditional Chi
-
Slightly off-topic: app for ripping dvd of film in public domain
Hi I want to use a few snippets of a film in the public domain, The Green Promise, in a music video for this flick I'm working on. Archive.org, where I can download it, only has what they call a 512kb.mpeg4 version (I take it an mpeg4 export of a 512
-
Oracle insert speed (92k records)
I am inserting 92,000 records into oracle (nightly job) I am just trying to speed things up (is my first C#/Oracle app) at the moment, I have 2 ways of inserting the records using Oracle.DataAccess.Client; using Oracle.DataAccess.Types; 1) command.Co