VLAN error in CCA
Hi,
Im new to the whole VOIP area and the UC520 so I would appreciate some help.
I have set up the UC520 which was fairly simple but I get a Select Vlan ID error in the telephony voice section of CCA. When I try to select a VLAN the drop down list is emtpy and it prevents me from saving any other information associated with the user and analog extentions etc.
I have changed the Data Vlan 1 to a different subnet but left the phone VLAN 100 as it was.
I did read somewhere that the CCA will error if you change the default VLAN's. the interesting thing is the information for the VLAN is all there just no VLAN ID. can anyone tell me a work around.
Any help would be much appreciated
Regards
Hi,
Sorted it out, turns out the was and issue with the vlan100 once I recreated it it work fine
Regards
Similar Messages
-
UC500 Multisite manager error in CCA
I am getting message when I click on Multisite Manager within CCA
"Multisite Manager was not able to retrieve the current configuration
Please make sure that device descovery has completed and then press Cancel below and restart Multisite Manager
If the problem persists, please contact Cisco support for further assistance"
I have already reset the UC540 to factory default but getting same error message, also update Java. can anyone advise
Thanks
HasratHi Shawn,
Multisite manager is used to configure a VPN that allows calls between 2 or more UC’s. New additions to CCA allow the multisite manager to also create just a data VPN without the dial plans to another router.
The multisite manger will configure the crypto maps and ACL’s on the UC. So if you are doing this remotely through a VPN there is always a chance that you will lose your connection. If you need additional information on the Multisite manger please let me know.
Thank you,
Jason Nickle -
Hi there,
This time I had strange messages while implementing CCA retractor and found following -
Error - You have no authorisation to change planning of Cost center DE1010511.
When I debugged found that below function module was throwing errors.
BAPI_COSTACTPLN_CHECKPRIMCOST
Does this mean that I dont have access to this cost center or its the ALEREMOTE user?
Anybody has an idea on this.?
regards
GRai
Edited by: G Rai on Jul 2, 2008 10:20 AMHi Rai,
Your RFC connection user Id does not have the authorisation for the cost center planning in the target system. If you give the necessary authorisation, it should work.
Regards,
Mike -
Catlyst Express 500 - ASA 5520 (VLAN Error)
Hello,
I am currently attempting to configure 2 VLANs on my ASA5520 and allow them to communication with my Catalyst 500 switch. The ASA Setup is fairly simple (to start) its 2 Sub-ints on the g0/0 interface. The Switch IP is 66.38.173.xxx 255.255.255.224
Int g0/0.1 vlan 10 Nameif outside66 ip: 66.38.173.xxx 255.255.255.224
Int g0/0.2 vlan 20 Nameif outside64 ip: 64.187.16.xxx 255.255.255.224
G0/0 Port on the ASA is connected to port 2 on my Catalyst. I set the Smartport on port 2 of the Catalyst to be Router for trunking purposes (I also tried Switch during testing). For some reason I cant ping from the ASA to the switch? I have also set up an access list to Allow ICMP Any any on the ASA.
I get a notification error on the Catalyst saying "Undersized frames detected from the connected device" (which is my ASA). This notification comes up each time I try to ping from the ASA to the Catalyst... does anyone have a suggestion? Or a link to sample config.
Thanks,
ChrisThe issue may be due to NIC card or there was a Xerox printer that had Netware support enabled; switching this off may
drop the undersized count. -
CCA 3.2.1 - Changing voice VLAN gets java.lang.nullPointerException
Hi,
I am trying to change the default VLAN number for voice to 32 from 100. At the time of apply changes, I get java.lang.nullpointerException error in CCA. If I make changes to the device command line then Cisco would not support + all command line changes are not showing up in the CCA anymore.
How to get out of this frustrating issue?
I know this is not a Java version or laptop issue because I tried latest version of Java on 3 different PC and all of them report this issue.
Thanks,
SamI having a similar problem. The java console reports:
1.0
100
SmartPortsGlobalSettings
07:14:03,033 [CLI ] CLIEngine: Executed: https://192.168.16.1/exec/show/vlan-switch/CR
07:14:03,126 [CLI ] CLIEngine: Executed: https://192.168.16.1/exec/show/vlan-switch/CR
07:14:03,204 [CLI ] CLIEngine: Executed: https://192.168.16.1/configure/vlan/100/CR
07:14:03,392 [CLI ] CLIEngine: Executed: https://192.168.16.1/config-vlan/100/name/Cisco-Voice/CR
07:14:03,392 [DEBUG] Could not set name to extended vlan
07:14:03,470 [CLI ] CLIEngine: Executed: https://192.168.16.1/config-vlan/100/state/active/CR
07:14:03,470 [DEBUG] Could not set name to extended vlan
07:14:03,548 [CLI ] CLIEngine: Executed: https://192.168.16.1/exec/show/parse/macro/description/CR
07:14:03,829 [CLI ] CLIEngine: Executed: https://192.168.16.1/exec/show/running-config/CR
07:14:05,407 [ERROR] java.lang.NullPointerException
07:14:05,407 [ERROR] at com.cisco.cpnm.features.mcebu.c2K.vlan.C2KVlanConfigTask.fillOldandNewIPInfo(C2KVlanConfigTask.java:1095)
07:14:05,407 [ERROR] at com.cisco.cpnm.features.mcebu.c2K.vlan.C2KVlanConfigTask.updateDeviceFromMirror(C2KVlanConfigTask.java:840)
07:14:05,407 [ERROR] at com.cisco.cpnm.frmwrk.gen.wd.WDComponent.updateDeviceFromMirror(WDComponent.java:646)
07:14:05,407 [ERROR] at com.cisco.cpnm.frmwrk.gen.wd.WDContainer.updateDeviceFromMirror(WDContainer.java:887)
07:14:05,407 [ERROR] at com.cisco.cpnm.frmwrk.net.wd.EventAwareTask.updateDeviceFromMirror(EventAwareTask.java:419)
07:14:05,407 [ERROR] at com.cisco.cpnm.frmwrk.gen.wd.WDContainer.updateDeviceFromMirror(WDContainer.java:887)
07:14:05,407 [ERROR] at com.cisco.cpnm.frmwrk.net.wd.EventAwareTask.updateDeviceFromMirror(EventAwareTask.java:419)
07:14:05,407 [ERROR] at com.cisco.cpnm.frmwrk.gen.wd.WDContainer.updateDeviceFromMirror(WDContainer.java:887)
07:14:05,407 [ERROR] at com.cisco.cpnm.frmwrk.gen.wd.WDTask$SetConfigRunnable.run(WDTask.java:1339)
07:14:05,407 [ERROR] at java.lang.Thread.run(Unknown Source)
07:14:05,469 [DEBUG]
[MULTIWINDOW] ****dialogStateChanged state = 1 component = VLANUI **** -
Error while opening excel integration with sap
Hi
While view planning with excel integration in SAP, I am getting error. I am getting this error in CCA and COPA also.
Can anybody help me how to resolve the issue. Please see the meessage
Error while opening document
Message no. SOFFICEINTEGRATION143
Diagnosis
An error occurred in the desktop application while opening a document.
Procedure
Check first whether you can insert a document from this desktop application as an embedded object in another application. The necessary menu item is usually 'Insert --> Object'. The application then lists all of the OLE document types. Choose the type corresponding to the desktop applciation. If the insertion fails, the error is in the desktop application itself.
This error has various causes. Often, it is caused by activating certain add-ins. Sometimes, the desktop application is wrongly installed. The error should not recur once you have disabled any add-ins or reinstalled the desktop application.
Procedure for System Administration
If you cannot solve the problem as described above, enter a problem message. There are notes relating to how to generate the log file using the program SAPROFFICEINTEGRATIONTRACE.
Regards
Sekhar DattaHi ,
I think you are using older version,use microsoft excel 2007 version,then it will opens.
Regrads,
SVS
Edited by: svskumar on Aug 19, 2010 12:18 PM -
Hi All,
I'm currently (pain-stakingly) trying to do what should be a simple task of upgrading a number of 7945's on a UC520.
CCA is 3.3.2 and the UC520 on 8.6.
The 7945's are on 8.3.2, Im trying to go to 8.5.2.
Any attempt to drag and drop results in the cursor icon symbolising the drag/drop feature (of any type) is not supported.
So to confirm no errors, no CCA prompts or notifications of any type, just what looks like a windows icon suggesting its not possible.
TFTP server is operational as I can upload software packs etc. and download configs.
Am I missing something, surely this should be a simple task...?
Any help would be very much appreciated.
Thanks,
GaryHello,
Please review the follow document to verify connection requirements:
https://supportforums.cisco.com/docs/DOC-9779
What is the file you are uploading? It should be a ZIP file.
Is there a reason you don't want to upgrade to 9.1.1 which is included in the software pack?
Nevermind, I doublechecked the release notes from 9.1.1SR1 which states:
For all SCCP firmware upgrades from firmware release versions earlier than 8.3(3) to version 8.5(2)SR1 or greater, you must first upgrade your firmware to version 8.5(2). Once you have upgraded to version 8.5(2), you can upgrade your IP Phone to version 9.1(1)SR1 or later.
http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/firmware/9_1_1/english/release/notes/7900_911.html#wp42493
Thanks,
-john -
L3 LWAPP Discovery reject wrong vlan...
Hi,
I have 10 APs (Static IP) connected to my existing Wireless LAN controller in subnet of 192.168.1.x network in VLAN 127.
The WLC (ver 4.1.171) is connected to a switch in trunk mode carrying VLANs 127-128. The managemet interface is configured as 10.1.1.1 part of VLAN 128 subnet. AP Manager interface is configured under VLAN 127 and having IP address 192.168.1.2.
Now, I am getting L3 LWAPP Discovery reject messages on WLC giving the Wrong VLAN error.
Is there any solution for this?
And also, I am able to create WLAN interfaces (like WIFI for VLAN 128) but not able to assign the same interface in SSID config page. It's getting defaulted to Management interface and NOT giving option to choose any other interface. What's the use of creation of dynamic interfaces in this case?
Regards...
-Ashok.It is totally OK to have different subnets for management an AP manager. The message you are seeing is because the APs send a broadcast discovery and since they are on AP manager subnet, they reach the WLC on that vlan with discoveries (and discovery requests are expected on the management interface).
The message is not a problem by itself if you configured DNS resolution or any other mechanism for the AP to learn the management ip of the WLC. You also need a gateway to route between those 2 subnets.
To create dynamic interfaces you need to assign them extra vlans on top of your 127,128. -
I have a CAM/CAS deployment in L2 OOB - vlan 545 trunked to untrusted and vlan 245 trunked to the trusted side. The switch/device/port profiles are setup via snmpv3. The switchport is not being bounced since the IP address is not being changed from auth vlan to access vlan. I hook a PC up and I get the CCA login page when I try and access a website on the trusted network. I put in some valid credentials and I see the snmp information being sent to the switch. Howerver, the switchport never changes to the access vlan and the CCA login page re-displays itself. What could I be missing here?
Hello,
Logically I would say that SNMP is not configured correctly.
Could you try to change to version 1 and see if that works? Then you are sure that the NAC appliance is configured correctly.
Can you tell us what kind of switch you are using as access switch?
If you're switch is L3 (on network level, not on NAC level) then C6500 and C4500, no problem. C3750/C3560 must be running 12.2(25)SEE or higher. C3550 is not supported to be in L3.
For more detail, see following matrix: http://www.cisco.com/univercd/cc/td/doc/product/vpn/ciscosec/cca/cca40/switch.htm#wp60598
hope this helps. -
Doubt with Dynamic Interfaces and VLANs
Hello.
I am trying to get wirelles clientes and APs to be on the same VLAN/subnet, now is working with management interface on my WLC 5508. My problem comes up when I change them to a new dynamic interface.
Before any change:
VLAN: 8
Management Interface IP: 192.168.9.2/23
Gateway: 192.168.8.1
DHCP Server: 192.168.8.2
WLAN SSID linked to Managment interface: Ray123
APs on VLAN 8 and subnet static IP range192.168.9.0/23
There is no dynamic interface.
After changes.
VLAN: 0
Management Interface: 192.168.6.2/23
Gateway: 192.168.6.1
DHCP Server: 192.168.6.2
Dynamic interface name: Wireless-1
VLAN: 8
Management Interface IP: 192.168.9.2/23
Gateway: 192.168.8.1
DHCP Server: 192.168.8.2
WLAN SSID linked to Dynamic interface: Ray123
APs still on VLAN 8 and subnet static IP range192.168.9.0/23
After all this done i can see by cdp neighbors all my APs i can ping them and management interface too, but APs are not registered, no clients too.
According to this guide:
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00805e7a24.shtml
Dynamic interfaces and APs should be on the same VLAN.
But this another guide states the opposite:
http://www.cisco.com/en/US/docs/wireless/controller/7.0/configuration/guide/c70mint.html
"Set the APs in a VLAN that is different from the dynamic interface configured on the Controller. If the APs are in the same VLAN as the dynamic interface, the APs are not registered on the Controller and the 'LWAPP discovery rejected' and 'Layer 3 discovery request not received on management VLAN' errors are logged on the Controller"
I cant understand why VLANs for APs and dynamic interfaces should be on different, it has no sense to configure a vlan intended for APs which shouldnt be on the same vlan.
Please tell me what is wrong.
Thanks in advance.You have to tell the APs where the WLC lives now, 192.168.6.2.
You can do this in the following ways:
Manual Prime the APs
option 43
dns
ip forward udp 5246
move the aps to the same vlan as the management interface let them join and then chnage the vlan
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
"I'm in a serious relationship with my Wi-Fi. You could say we have a connection." -
How to run ccastart in background?
Hi,
Is there any way to run the ccastart in Linux, so it remains started even when the session that started it, has finished? The idea is that I can login into the server, start the ccastart and close the window I used to started.... Now whenever I close the Xming (which I use to connect to the server), the ccastart stops and the scheduled jobs are not run because of it.
Environment: OWB 11gR2 (11.2.0.2),
- Jobs to run mappings successfully working when Xming console opened,
- When I close my Xming session, and later on I check the Control Center - Scheduled tab, I can see that the jobs are not ok, and the reported error is: CCA-1536: the control center agent is not available, re-start it. Details: error reading application-server descriptor. Error communicating with server. Connection refused.
Any help will be appreciated.
Cheers,
AnaInclude in start shell (ccastart) -Djava.awt.headless=true
$JAVA_HOME/bin/java $JAVA64FLAG -Djava.awt.headless=true -Dapi.ext.dirs=$OWB_HOME/owb/lib/ext -Doracle.home=$OC4J_HOME -Doracle.j2ee.home=$OWB_JRT_RUN_HOME -Dpython.path=$OWB_JRT_RUN_HOME/applications/jrt/jython_lib.zip:$OWB_JRT_RUN_HOME/applications/jrt/jython_owblib.jar $JRT_JVM_XOPTS $JRT_JVM_DOPTS $OWB_JVM_OPTS -Xmx896M -jar $OC4J_HOME/j2ee/home/oc4j.jar -config $OWB_JRT_RUN_HOME/config/server.xml >> $LOG_FILE 2>&1 &
and to start :
nohup ./ccastart > $FICHLOG 2>&1 &
cheers -
Integration Chat Siebel cca813
Hi, I imported the driver multichannelC.def (Language : PTB) in Siebel and configured the agents, but when I login, it loads the toolbar and shows the message 'disconected'.
Could you help me please?
Tks
Log tw-summit_xxxxx.log
CustomId: 352003
[10/28/2009 14:36:24:625]:INFO:Opening ADMIN Application Session succeed!
[10/28/2009 14:36:24:625]:INFO:Starting GetAllMsgFunc Thread succeed!
[10/28/2009 14:36:24:625]:INFO:Starting ParseSOAPFunc Thread succeed!
[10/28/2009 14:36:24:625]:DEBUG:Starting GetAllMsgFunc Thread
[10/28/2009 14:36:24:625]:DEBUG:Starting ParseSOAPFunc Thread
[10/28/2009 14:36:24:625]:DEBUG:Starting ProcessEventFunc Thread
[10/28/2009 14:36:24:625]:DEBUG:Begin: ProcessEventFunc
[10/28/2009 14:36:24:625]:DEBUG:End: ProcessEventFunc
[10/28/2009 14:36:24:625]:INFO:Starting ProcessEventFunc Thread succeed!
[10/28/2009 14:36:24:625]:INFO:Driver initialization succeed!
[10/28/2009 14:36:24:625]:INFO:Add driver instance into driver list.
[10/28/2009 14:36:24:625]:INFO:Driver increases reference, count=1
[10/28/2009 14:36:24:640]:DEBUG:Add new service into service list.
[10/28/2009 14:36:25:687]:ERROR:ParseSOAPFunc: CCA Erro! Empresa inatingivel. (*CCA Error! Company unattainable.*)
[10/28/2009 14:36:25:687]:DEBUG:ParseSOAPFunc : Failed count=1
[10/28/2009 14:36:26:718]:ERROR:ParseSOAPFunc: CCA Erro! Empresa inatingivel.
[10/28/2009 14:36:26:718]:DEBUG:ParseSOAPFunc : Failed count=2
[10/28/2009 14:36:27:734]:ERROR:ParseSOAPFunc: CCA Erro! Empresa inatingivel.
[10/28/2009 14:36:27:734]:DEBUG:ParseSOAPFunc : Failed count=3
[10/28/2009 14:36:28:765]:ERROR:ParseSOAPFunc: CCA Erro! Empresa inatingivel.
[10/28/2009 14:36:28:765]:DEBUG:ParseSOAPFunc : Failed count=4
[10/28/2009 14:36:29:781]:ERROR:ParseSOAPFunc: CCA Erro! Empresa inatingivel.
[10/28/2009 14:36:29:781]:DEBUG:ParseSOAPFunc : Failed count=5
[10/28/2009 14:36:30:828]:ERROR:ParseSOAPFunc: CCA Erro! Empresa inatingivel.
[10/28/2009 14:36:30:828]:DEBUG:ParseSOAPFunc : Failed count=6
[10/28/2009 14:36:31:828]:ERROR:ParseSOAPFunc: CCA Erro! Empresa inatingivel.
[10/28/2009 14:36:31:843]:DEBUG:ParseSOAPFunc : Failed count=7
[10/28/2009 14:36:32:875]:ERROR:ParseSOAPFunc: CCA Erro! Empresa inatingivel.
[10/28/2009 14:36:32:875]:DEBUG:ParseSOAPFunc : Failed count=8
[10/28/2009 14:36:33:875]:ERROR:ParseSOAPFunc: CCA Erro! Empresa inatingivel.
[10/28/2009 14:36:33:875]:DEBUG:ParseSOAPFunc : Failed count=9
[10/28/2009 14:36:34:937]:ERROR:ParseSOAPFunc: CCA Erro! Empresa inatingivel.
[10/28/2009 14:36:34:937]:DEBUG:ParseSOAPFunc : Failed count=10
[10/28/2009 14:36:34:937]:ERROR:No backup CCA server configured, couldn't complete switch!
[10/28/2009 14:36:34:937]:FATAL:ParseSOAPFunc : Shutting Down!
[10/28/2009 14:36:34:937]:INFO:LogoutAgent: Erro fatal! Servidor CCA desconectado! Logout automático!
[10/28/2009 14:36:39:984]:INFO:Stopping GetAllMsg Thread succeed!
[10/28/2009 14:36:40:078]:DEBUG:Exiting GetAllMsgFunc Thread
[10/28/2009 14:36:44:984]:INFO:Stopping ParseSOAP Thread succeed!
[10/28/2009 14:36:49:984]:INFO:Stopping ProcessEvent Thread succeed!
[10/28/2009 14:36:49:984]:DEBUG:Exiting ParseSOAPFunc Thread
[10/28/2009 14:36:50:062]:DEBUG:Exiting ProcessEventFunc Thread
[10/28/2009 14:38:30:875]:DEBUG:Remove service from service list.
[10/28/2009 14:38:30:875]:INFO:Driver descrease reference,count=0
[10/28/2009 14:38:30:875]:INFO:Remove driver instance from driver list.
[10/28/2009 14:58:05:703]:INFO:Max Connection: 2
[10/28/2009 14:58:05:703]:INFO:GetUniqueID
[10/28/2009 14:58:05:703]:DEBUG:ProcessId : 3520, Seed : 4
[10/28/2009 14:58:05:703]:DEBUG:TaW Driver Parameter:
URL = http://172.23.2.12:8080/CCA/services/
AutoProxyRefreshInterval = -1
LogSOAPFile = twsoap-summit.log
BackupURL =
EventRetry = 10
UnknownCCAValue = ??
RefreshUserExtensionInterval = 3600
LogFile = tw-summit.log
SOAPRetry = 3
OnHookAtLogout = TRUE
ProxyLocation =
CountryCodeDelimiter = .
DefaultCountryCode = 1
ProxySupport = Disabled
MaxMessageNumber = 50
MessageInterval = 1000
MaxLogKB = 90240
AdminUserName = admin
CompanyName = system
MaxAgentNumber = -1
ReleaseLogHandle = TRUE
VoiceDescription = [ANI]
EnableSOAPTrace = FALSE
LogDebug = TRUE
AdminPassword = adminYou will need to configure your communications driver parameters to match your CCA settings such as company alias. The error is saying that the company is not found. The defualt in the DEF file is company summit which is probably not in your CCA.
-
Hi
Just bought this router as Cisco have a good reputation, but i've never owned a product that's so Beta'ish. Allmost nothing is working as it should with firmware 1.0.4.17, and it has not been updated since August 2012.
I've tried to setup normal portforward, without luck, i've tried to setup PPTP VPN, but having problems, if i do it like the manual says(Same network as VLan error). Simple things that should be working on a product like this, without any problems.
I'm for sure going to return this router to the seller.
Best regards
ThomasHi Thomas,
I would have thoght that August 2012 release firmware would still count as current. To release firmware in a complex product requires a lot of testing (hopefully!) and 1.0.4.17 did fix a lot of bugs. I would hope that Cisco is working a new release however I would not have expected it to be released yet.
Your problem sounds like it could be a set-up problem. It seems that a lot of users have got PPTP VPN working. If you are still having problems then provide some information for the forum People like Tom are very helpful and seem very
knowledgeable. Alternatively you can place a call with Cisco.
Goold luck,
David -
What is the "ingress over sub drops" counter // ASR1000?
Hello,
can you tell me what is the "ingress over sub drops" counter in the following output (ASR1004, 15.2(2)S1)?
asr#show controllers
<...>
TenGigabitEthernet0/1/0
21830397 input vlan errors
7712082 ingress over sub drops
18 Number of sub-interface configured
<...>
Thank you,
best regards,
GergelyHello,
thank you for your reply!
This is a tengig interface which is not likely to oversubscribe (typical traffic rate is below 2.5 Gbps) however there could be some bursty traffic concerning this counter.
There is no input queue drop on the interface - I wonder if the "input queue drop" related to "ingress over sub drops"?
Best regards,
Gergely
asr#sh int ten 0/1/0 controller
TenGigabitEthernet0/1/0 is up, line protocol is up
Hardware is SPA-1X10GE-L-V2, address is a493.4cd0.c510 (bia a493.4cd0.c510)
MTU 9216 bytes, BW 10000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 60/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 1., loopback not set
Keepalive not supported
Full Duplex, 10000Mbps, link type is force-up, media type is 10GBase-SR
output flow-control is on, input flow-control is on
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:01:29, output hang never
Last clearing of "show interface" counters never
Input queue: 0/375/0/0 (size/max/drops/flushes); Total output drops: 195
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 2371308000 bits/sec, 218149 packets/sec
30 second output rate 2000 bits/sec, 4 packets/sec
295771623646 packets input, 401390419037397 bytes, 0 no buffer
Received 17352252 broadcasts (294214973196 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 2559103491 multicast, 0 pause input
205479375 packets output, 266095482233 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
TenGigabitEthernet0/1/0
21831585 input vlan errors
7712082 ingress over sub drops
18 Number of sub-interface configured
asr# -
Getting error about VLAN not existing on radio
When I try to enable the 5ghz radio on my AIR-AP1142N-A-K9 I get the following error:
VLAN '100' doesn't exist on 'Radio1-802.11N 5GHz' (see Services>VLAN)
In the vlan it is enabled. What gives?
Config below:
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap-1140-southwing
logging rate-limit console 9
enable secret xxxxxxxxxxxxxxxxxxxx
aaa new-model
aaa group server radius rad_eap
server 192.168.1.187 auth-port 1812 acct-port 1813
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
server 192.168.1.187 auth-port 1812 acct-port 1813
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
clock timezone CST -6
clock summer-time CDT recurring
dot11 syslog
dot11 vlan-name 5gwifi vlan 300
dot11 vlan-name jchcenterprise vlan 130
dot11 vlan-name public vlan 100
dot11 ssid jchccorp
vlan 120
authentication open
authentication key-management wpa version 2
mbssid guest-mode
wpa-psk ascii 7 115A4A50461808040778797478
dot11 ssid jchcpublic
vlan 100
authentication open
mbssid guest-mode
username Cisco password 7 10640C1C15435C5B
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 120 mode ciphers aes-ccm tkip
encryption vlan 130 mode ciphers aes-ccm tkip
ssid jchccorp
ssid jchcpublic
antenna gain 0
mbssid
channel width 40-below
channel 2422
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.100
encapsulation dot1Q 100
no ip route-cache
bridge-group 100
bridge-group 100 subscriber-loop-control
bridge-group 100 block-unknown-source
no bridge-group 100 source-learning
no bridge-group 100 unicast-flooding
bridge-group 100 spanning-disabled
interface Dot11Radio0.120
encapsulation dot1Q 120
no ip route-cache
bridge-group 120
bridge-group 120 subscriber-loop-control
bridge-group 120 block-unknown-source
no bridge-group 120 source-learning
no bridge-group 120 unicast-flooding
bridge-group 120 spanning-disabled
interface Dot11Radio0.130
encapsulation dot1Q 130
no ip route-cache
bridge-group 130
bridge-group 130 subscriber-loop-control
bridge-group 130 block-unknown-source
no bridge-group 130 source-learning
no bridge-group 130 unicast-flooding
bridge-group 130 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 120 mode ciphers aes-ccm tkip
encryption vlan 300 mode ciphers aes-ccm tkip
ssid jchccorp
antenna gain 0
dfs band 3 block
mbssid
speed basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel width 40-above
channel 5180
station-role root
bridge-group 1
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1.100
encapsulation dot1Q 100
no ip route-cache
bridge-group 100
bridge-group 100 subscriber-loop-control
bridge-group 100 block-unknown-source
no bridge-group 100 source-learning
no bridge-group 100 unicast-flooding
bridge-group 100 spanning-disabled
interface Dot11Radio1.120
encapsulation dot1Q 120
no ip route-cache
bridge-group 120
bridge-group 120 subscriber-loop-control
bridge-group 120 block-unknown-source
no bridge-group 120 source-learning
no bridge-group 120 unicast-flooding
bridge-group 120 spanning-disabled
interface Dot11Radio1.300
encapsulation dot1Q 300
no ip route-cache
bridge-group 255
bridge-group 255 subscriber-loop-control
bridge-group 255 block-unknown-source
no bridge-group 255 source-learning
no bridge-group 255 unicast-flooding
bridge-group 255 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface GigabitEthernet0.100
encapsulation dot1Q 100
no ip route-cache
bridge-group 100
no bridge-group 100 source-learning
bridge-group 100 spanning-disabled
interface GigabitEthernet0.120
encapsulation dot1Q 120
no ip route-cache
bridge-group 120
no bridge-group 120 source-learning
bridge-group 120 spanning-disabled
interface GigabitEthernet0.130
encapsulation dot1Q 130
no ip route-cache
bridge-group 130
no bridge-group 130 source-learning
bridge-group 130 spanning-disabled
interface GigabitEthernet0.300
encapsulation dot1Q 300
no ip route-cache
bridge-group 255
no bridge-group 255 source-learning
bridge-group 255 spanning-disabled
interface BVI1
ip address 192.168.1.195 255.255.255.0
no ip route-cache
ip default-gateway 192.168.1.35
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
radius-server attribute 32 include-in-access-req format %h
radius-server host 192.168.1.187 auth-port 1812 acct-port 1813 key 7 002E161650155B
radius-server vsa send accounting
bridge 1 route ip
line con 0
line vty 0 4
enddot11 ssid jchccorp
vlan 120
authentication open
authentication key-management wpa version 2
mbssid guest-mode
wpa-psk ascii 7 115A4A50461808040778797478
dot11 ssid jchcpublic
vlan 100
authentication open
mbssid guest-mode
You have 2 SSID's defined using vlan 120 and vlan 100, if you need another SSID, you need to define the vlan also. If you just want jchcorp on the 5ghz:
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 120 mode ciphers aes-ccm tkip
ssid jchccorp
interface Dot11Radio1.100
encapsulation dot1Q 100
no ip route-cache
bridge-group 100
bridge-group 100 subscriber-loop-control
bridge-group 100 block-unknown-source
no bridge-group 100 source-learning
no bridge-group 100 unicast-flooding
bridge-group 100 spanning-disabled
interface Dot11Radio1.120
encapsulation dot1Q 120
no ip route-cache
bridge-group 120
bridge-group 120 subscriber-loop-control
bridge-group 120 block-unknown-source
no bridge-group 120 source-learning
no bridge-group 120 unicast-flooding
bridge-group 120 spanning-disabled
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"
Maybe you are looking for
-
Getting Error in Windows 8.1 XAML code when using Microsoft.PlayerFramework
Error Is: The specified value cannot be assigned to the collection. the following type was expected UIelement xmlns:player="using:Microsoft.PlayerFramework" <Border x:Name="Border" DataContext="{TemplateBinding ViewModel}"> <Border.Resources> <player
-
Hello folks. This is my last attempt to locate a solution for why my DWMX is not displaying all my files in my local or remote folder. I have a new client who has put us in charge of moving their site to a new server. When I create a new site in DWMX
-
Assignment field in Payment Proposal Display
Hi, I would like to have Assignment field in Payment Proposal Display. I checked in Tcode O7Z6 but could not find the option Can anyone let me is this possibel..if yes what is the way thanks, JR
-
Reader 10.0.1 errors when opening in IE8 browser window on win7 x64
These errors are being seen inconsistently on several of the 200+ test machines Adr 10.0.1 has been rolled out to. Some PDFs or websites are causing the Rdr app to throw the following errors: "There is a problem with Adobe Acrobat/Reader. If it is r
-
Xcelsius with SAP netweaver connection extremely slow when executing
Hi everybody, I am building a quite complex Xcelsius dashboard with multiple connections and many components with individual mappings. My initial load time is now around 5 minutes (the netweaver portal loading icon) and the initialization is around 1