VLAN for WLC interface (ISE Policies Based on SSID)

I have ISE 1.1 and WLC 2504
I used this link http://www.cisco.com/en/US/products/ps11640/products_configuration_example09186a0080bed902.shtml
But I am confuse on the WLC configuration
If I have only one ESSID for corporate user(and many DATA vlan because each AD group is assosiated to one specific VLAN)
I have already created Management interface associated with management Vlan
Wich interface interface should I associate on the corparate WAN ( WLAN -->General --->Interface/interface group) ?
Should I create another interface ? wich Vlan ID should I associate to this interface
or should I use Management interface
Please advise

check the following links , they are very helpful:
http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a00808c9bd1.shtml
http://www.cisco.com/en/US/products/ps10315/products_configuration_example09186a0080bc8129.shtml
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml
Please make sure to rate correct answers

Similar Messages

Dedicated vlan for WLC

Hi,
In reviewing the lab for WLC configuration, they used a dedicated vlan for all APs and the WLC to communicate with CAPWAP.
In the production environment I'm designing for, a campus network that has many LAN connected sites all with different vlans at the edge, that would entail trunking another vlan out to the edge switches. It also requires the MetroEthernet provider to provision the same beforehand.
One of the advantages of the WLC is the ability to avoid having to add vlans at the edge for WLANs, but what about a dedicated vlan for the APs and WLC to communicate with CAPWAP? A best practice?
Thanks.

As best practice we've only two options, keep the AP on L2 vlan(not scalable) of management or on any L3(vlan that is not part of dynamic interface of WLC) which is scalable and good for highavailability.

VLAN for AP interface

Hello,
could you help me is it best practice to place LAP-AP interfaces to magement VLAN?
Thanks in advance

ok, is it safe to place LAPs to in-band management VLAN?

WLC, FlexConnect, ISE: Dynamic VLAN not working

Hi,
Not sure if this is a WLC or ISE problem, but since I am unsure of the WLC config I will try here first.
Equipment:
WiSM2 7.2.111.3
ISE 1.1.1.268
AP 3502 in FlexConnect
What I want to achive:
One SSID, multiple VLAN
Devices gets profiled in ISE and based on type of device it gets asigned to a VLAN
Problem:
When the device connects the first time it ends up in native VLAN and not switched to the right VLAN, but when I reconnect then it is added to the right VLAN.
WLC config (I know you like images so here you go ):
I must be missing something but I can't figure out what. I will be attaching a debug aaa event enable for when the client connect the first time.
In ISE I have an Authorization Profile that just say VLAN ID/Tag 158 (the VLAN that the device should go to) an it is added to the Authorization rule of the profiled device. CoA is set to Reauth.
When the client connects I get three events in ISE:
1.
Authentication failed :
22056 Subject not found in the applicable identity store(s)
2. Authentication Success. With the results:
UserName=00:18:DE:A2:BC:3A
User-Name=00-18-DE-A2-BC-3A
State=ReauthSession:c20e8b2f0000027e50ed27f8
Class=CACS:c20e8b2f0000027e50ed27f8:ISE01/144259326/671335
Termination-Action=RADIUS-Request
Tunnel-Type=(tag=1) VLAN
Tunnel-Medium-Type=(tag=1) 802
Tunnel-Private-Group-ID=(tag=1) 158
cisco-av-pair=profile-name=AX-Intel-Device
3.
Dynamic Authorization failed :
11213 No response received from Network Access Device
Has anyone got this to work? Do I need to add FlexConnect groups? If so then why?
Regards,
Philip

I think you're hitting CSCua58554
The bugtoolkit description is horrible.... From what I recall when I ran into it, I believe that Flex connect is having a problem with Mac filtering based AAA override on open wlans (and/or CWA based). In general, AAA override works fine when it is from like an eap authentication.
We had to use a 7.3 ES to resolve it.....
Looks like it is implemented in 7.4 though..... If you dont want to join the 7.4 bandwagon quite yet, you might could ask TAC for an ES of 7.3, don't think they have a 7.2 build.

WLC to ISE authentication for Guest

Hi Experts,
Hope if you could guide me with our setup for Guest users. Below is what we are doing
a)     Guest connects to SSID
b)     WLC is being used to redirect Guest HTTP to WLC internal Portal
c)     WLC forwards guest authentication details to cisco ISE [ISE and WLC radius]
The guest connects to SSID and does get WLC portal for authentication, when the username and password entered on Cisco ISE i see error message as
'User Identity not found in any of Identity Store' though it is going through correct Store and the Guest name is certainly configured on Cisco ISE. ISE version is 1.2 and WLC is 7.4, please let me know if i am missing anything here.
Appreciate your help

The first method is local web authentication. In this case, the WLC redirects the HTTP traffic to an internal or external server where the user is prompted to authenticate. The WLC then fetches the credentials (sent back via an HTTP GET request in the case of external server) and makes a RADIUS authentication. In the case of a guest user, an external server (such as Identity Services Engine (ISE) or NAC Guest Server (NGS)) is required as the portal provides features such as device registering and self-provisioning. The flow includes these steps:
Please follow below guide for step by step configuration:
http://www.cisco.com/en/US/products/ps11640/products_configuration_example09186a0080bead09.shtml

Different VLAN for AP and WLC

I have a problem when I rebulid my client's wireless network
My client's AP is using static IP address on AP1131AG in VLAN 50, but the controller is at VLAN 100
A DHCP with option 43 and 60 is running on core switch, that's meaning if the AP is no IP setting that will work fine with on DHCP with option 43 and 60, this point I understood.
But in the AP which using static IP address, there has no DNS / WLC IP address setting can be found on the it, why the AP can associate to the controller without DNS / WLC IP address? I checked the configuration many times but no luck, hope someone can explain this to me, thanks a lot!

Thanks for your reply, i am asking why is it working......
As all APs have associated to the controller at the moment, I don't know why it's work on day one, as no broadcast forwarding setting on the corss VLAN L3 switch, and the DNS is no CAPWAP / LWAPP entry for WLC, so it's a big question mark to me, how the AP which running static IP is work fine even I shut it down for 10 hours and bring it back.
As you said, once the AP is joined the WLC, the AP won't to proceed the discovery, then....
Where is the WLC IP address stored in the AP? I used show run command but cannot found any ascii or hex value for WLC IP address
If I need to add a new AP in this enviroment, am i need to configura a static IP address and enable the boardcast forwarding on the L3 switch? But in case I enabled the boardcast forwarding, how's the AP in VLAN 50 can communicate with VLAN 100 through CAPWAP and join the WLC? and how is the AP can find the WLC IP address with no DNS IP configured in the APs.
I think the guys who setup this enviroment was enabled the boardcast forwarding, but disabled it after all of the APs joined the WLC, is it possible? I am looking forward for your reply, thanks!

ISE posture based upon switch user is connected to

OK, I am a new ISE user and definitely an early beginner on creating ISE policies. I have successfully created a policy that can determine if you are using a corporate asset or not and using 802.1x authentication grant you access to corporate resources or not. This policy also assigns the VLAN the user is placed into. Seems to work quite well so far at least as a baby step in policy creation.
Our building has different VLANS based upon floors and the like and I would like the policy(s) take this into consideration when assigning the VLAN. Is there a way to include which switch the postureing process is flowing through to assist in assigning the VLAN? I am thinking I would have separate policies based upon the switch / stack but not sure how to include that in the logic. I figured it would be similar to my policy where I check corporate assets and that you are wireless and that you have a valid AD account but have been unable to figure out the endpoint part. I have created network groups for my network devices but am stumped after that. Is there something else I should or could be doing instead? Do I need a completely different train of thought?
Brent

Hello Brent, using "Network Device Groups" can definitely make this possible for you. For instance, you can create a "Location" based group hierarchy that looks like something like this:
All Locations > HQ > Floor-1
All Locations > HQ > Floor-2
All Locations > DR > Floor-1
etc
Then you can reference that group in your authorization policy by using something like this
If "Conditions > Device > Location" = All Locations > HQ > Floor-1
then
Permissions = "HQ_Floor-1-Posture"
If "Conditions > Device > Location" = All Locations > HQ > Floor-2
then
Permissions = "HQ_Floor-2-Posture"
I hope this helps and addresses your issue.
Thank you for rating helpful posts!

Multiple WLANs pointing to same WLC interface

I would like to have a guest Web auth based WLAN that points to an Interface that I also have configured for a separate 802.1X authentication that allows access to my private network. I should note that I already have web auth configured for Guest access that only allows Internet access via separate WALN/VLAN. This would allow me to setup access for a vendor that is on-site using the Lobby Ambassador .
Is this possible and what do I need to do? I have created the seperate WLAN with Web auth and pointed it to the same WLC interface that I use for the 802.1X and this does not seem to work.

This has been resolved. I found I had AP groups setup and had not added the WALN to the correct group.

Question about Load Balancing Wireless connections using WLC- F5- ISE

Hi all,
Can anyone give me some orientation how the radius auth process/handshake between the WLC and ISE changes once the F5 is installed in the middle in order to perform load balancing?
We can do some kind of load balancing by configuring different radius servers on each WLC for which, I must configure the same shared secret in the WLC and ISE so the radius request/accept could be processed.
Now that we have the F5 in the middle, do I need to create/configure the same shared secret in the F5 so radius transactions can be processed by this device?. Based on the following link, I must configure the F5 in the ISE like another NAD device (similar to the WLC) but I do not know if this additional configuration in the ISE includes the Auth parameter to be added in the ISE NAD (F5) configuration.
How to properly use a load balancer in Cisco's Identity Services Engine
http://www.networkworld.com/community/blog/load-balancing-cisco-identity-services-engine
Our sheme is shown next,

When you covert the pair into SSO, all the APs will go to the ACTIVE unit. No unit will "live" in the standby unit because this unit will "share" the AP-support license between the two.
This is the first step you need to get sorted. Send an email to [email protected] and give them the exact details of what you want to do (i. e. AP SSO) and then provide the serial number of your nominated active WLC and the serial number of your nominated standby WLC.

Wlc interface

I created an interface (from Controller > Interface) assign an ip address on /24 subnet. Tested and it works fine. Now here's the confusion.
I remove the routing for that subnet. I can't ping the ip address of the interface created above, but I can still connect to the ssid. Any idea why? What is the purpose of using this interface?

Interfaces on WLC are Layer-2 and you need external L3 device for routing.
it is like SVI on switch but no Layer3(however it does some L3 for out of band management using static route config on wlc). With atleast one configured tagged vlan on WLC to its connected switch physical interface should always be trunked.
every active ssid(layer-1) needs to have interface/vlan(layer-2) mapped to it, without that it is an switch port with no vlan(including native) attached to it, however WLC mandate to select interface for all wlan created(default is management).
you should be able to ping the WLC interface ip, if the w.less client(with ip) connected wlan has same interface mapped to it or other interface with inter-vlan/L3 access.
Purpose of management interface is to carry AP traffic(that includes all wlan traffic), wlans can also be mapped to management interface(should avoid for security reasons), Dynamic interfaces mapped to wlans uses that subnet/vlan to talk to wired infrastructure from WLC to its connected switch using dynamic interface mapped physical interface. there is no wlan's mapped vlan id between wireless client until ingress physical port of WLC via AP, it is only wlc that tags the packet before forwarding to its upstream infrastruture device.

Cisco WLC with ISE - need to restrict access during non-business hours

Hello,
We have a requirement to turn off our wireless during non-business hours. We have a 5508 WLC with ISE. What is the best way to accomplish this task?
Thank you in advance.
Beth

Aside from Steve's respond, there are several methods of doing this and this will all depend on how complex your network is and how technical you want to do this.
1. As what Steve said, use PI and you can define several schedules when to turn off/on the SSID;
2. If you have corporate access, you can use AD to schedule non-business hours;
3. If you have Cisco PoE switches, you can enable EnergyWise to power off the APs;
4. If you manage your core network, you can enable time-based ACL to disable the default gateway of the dynamic interface which is attached to your SSID.
The most "destructive" method is option #3, because there are chances that your AP won't power up properly, if not power up at all.

Why is IP address needed for WLC WLANs?

I'm familiar with autonomous APs but am new to the WLC. Is there a way to just bridge the WLAN traffic to a VLAN? I don't understand why the WLC requires an IP address for the VLAN when the clients essentially are already on that VLAN. How is it used?
Thanks.
(Edit: fixed typo.)

the parameters specific to this VLAN. Some of the parameters include the IP Address, Netmask, Gateway, and the DHCP server IP address.
The IP address assigned to this interface acts as the DHCP relay for a client to obtain an IP address from the DHCP server. For example, when a client attempts to associate to a WLAN/SSID (see step 5 in this configuration) mapped to this dynamic interface, it performs a local subnet broadcast to identify the DHCP server. The controller sends a request to the DHCP server (or to itself if it is the DHCP server for the segment) with the IP address of this dynamic interface as relay IP to the DHCP server configured for this interface. The DHCP server assigns an IP address to the client from the configured DHCP scope.
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-vlan/68100-wlan-controllers-vlans.html

I Need Interactive Report for displaying vendor information. Based on the s

Interactive Report for displaying vendor information. Based on the selection made by the corresponding Vendor Bank Details are listed such that the line selected in the basic list was visible along with the secondary list.

hi
Hi
Use the Table LFA1 and LFB1 in the basic list
and LFBK table details in the secondary list
see the sample code related to customer Sales orders
modify it with the Vendor tables
REPORT ZTEJ_INTAB1 LINE-SIZE 103 LINE-COUNT 35(5) NO STANDARD PAGE
HEADING.
*TABLES DECLARATION
TABLES : KNA1, VBAK, VBAP.
*SELECT OPTIONS
SELECT-OPTIONS: CUST_NO FOR KNA1-KUNNR.
*INITIALIZATION
INITIALIZATION.
CUST_NO-LOW = '01'.
CUST_NO-HIGH = '5000'.
CUST_NO-SIGN = 'I'.
CUST_NO-OPTION = 'BT'.
APPEND CUST_NO.
*SELECTION SCREEN VALIDATION
AT SELECTION-SCREEN ON CUST_NO.
LOOP AT SCREEN.
IF CUST_NO-LOW < 1 OR CUST_NO-HIGH > 5000.
MESSAGE E001(ZTJ1).
ENDIF.
ENDLOOP.
*BASIC LIST SELECTION
START-OF-SELECTION.
SELECT KUNNR NAME1 ORT01 LAND1 INTO
(KNA1-KUNNR, KNA1-NAME1,KNA1-ORT01,KNA1-LAND1)
FROM KNA1
WHERE KUNNR IN CUST_NO.
WRITE:/1 SY-VLINE,
KNA1-KUNNR UNDER 'CUSTOMER NO.' HOTSPOT ON,
16 SY-VLINE,
KNA1-NAME1 UNDER 'NAME',
61 SY-VLINE,
KNA1-ORT01 UNDER 'CITY',
86 SY-VLINE,
KNA1-LAND1 UNDER 'COUNTRY',
103 SY-VLINE.
HIDE: KNA1-KUNNR.
ENDSELECT.
ULINE.
*SECONDARY LIST ACCESS
AT user-command.
IF SY-UCOMM = 'IONE'.
PERFORM SALES_ORD.
ENDIF.
IF SY-UCOMM = 'ITWO'.
PERFORM ITEM_DET.
ENDIF.
*TOP OF PAGE
TOP-OF-PAGE.
FORMAT COLOR 1.
WRITE : 'CUSTOMER DETAILS'.
FORMAT COLOR 1 OFF.
ULINE.
FORMAT COLOR 3.
WRITE : 1 SY-VLINE,
3 'CUSTOMER NO.',
16 SY-VLINE,
18 'NAME',
61 SY-VLINE,
63 'CITY',
86 SY-VLINE,
88 'COUNTRY',
103 SY-VLINE.
ULINE.
FORMAT COLOR 3 OFF.
*TOP OF PAGE FOR SECONDARY LISTS
TOP-OF-PAGE DURING LINE-SELECTION.
*TOP OF PAGE FOR 1ST SECONDARY LIST
IF SY-UCOMM = 'IONE'.
ULINE.
FORMAT COLOR 1.
WRITE : 'SALES ORDER DETAILS'.
ULINE.
FORMAT COLOR 1 OFF.
FORMAT COLOR 3.
WRITE : 1 SY-VLINE,
3 'CUSTOMER NO.',
16 SY-VLINE,
18 'SALES ORDER NO.',
40 SY-VLINE,
42 'DATE',
60 SY-VLINE,
62 'CREATOR',
85 SY-VLINE,
87 'DOC DATE',
103 SY-VLINE.
ULINE.
ENDIF.
FORMAT COLOR 3 OFF.
*TOP OF PAGE FOR 2ND SECONDARY LIST
IF SY-UCOMM = 'ITWO'.
ULINE.
FORMAT COLOR 1.
WRITE : 'ITEM DETAILS'.
ULINE.
FORMAT COLOR 1 OFF.
FORMAT COLOR 3.
WRITE : 1 SY-VLINE,
3 'SALES ORDER NO.',
40 SY-VLINE,
42 'SALES ITEM NO.',
60 SY-VLINE,
62 'ORDER QUANTITY',
103 SY-VLINE.
ULINE.
ENDIF.
FORMAT COLOR 3 OFF.
*END OF PAGE
END-OF-PAGE.
ULINE.
WRITE :'USER :',SY-UNAME,/,'DATE :', SY-DATUM, 85 'END OF PAGE:',
SY-PAGNO.
SKIP.
*& Form SALES_ORD
*& FIRST SECONDARY LIST FORM
FORM SALES_ORD .
SELECT KUNNR VBELN ERDAT ERNAM AUDAT INTO
(VBAK-KUNNR, VBAK-VBELN, VBAK-ERDAT, VBAK-ERNAM, VBAK-AUDAT)
FROM VBAK
WHERE KUNNR = KNA1-KUNNR.
WRITE:/1 SY-VLINE,
VBAK-KUNNR UNDER 'CUSTOMER NO.' HOTSPOT ON,
16 SY-VLINE,
VBAK-VBELN UNDER 'SALES ORDER NO.' HOTSPOT ON,
40 SY-VLINE,
VBAK-ERDAT UNDER 'DATE',
60 SY-VLINE,
VBAK-ERNAM UNDER 'CREATOR',
85 SY-VLINE,
VBAK-AUDAT UNDER 'DOC DATE',
103 SY-VLINE.
HIDE : VBAK-VBELN.
ENDSELECT.
ULINE.
ENDFORM. " SALES_ORD
*& Form ITEM_DET
*& SECOND SECONDARY LIST FORM
FORM ITEM_DET .
SELECT VBELN POSNR KWMENG INTO
(VBAP-VBELN, VBAP-POSNR, VBAP-KWMENG)
FROM VBAP
WHERE VBELN = VBAK-VBELN.
WRITE : /1 SY-VLINE,
VBAP-VBELN UNDER 'SALES ORDER NO.',
40 SY-VLINE,
VBAP-POSNR UNDER 'SALES ITEM NO.',
60 SY-VLINE,
VBAP-KWMENG UNDER 'ORDER QUANTITY',
103 SY-VLINE.
ENDSELECT.
ULINE.
ENDFORM. " ITEM_DET
REPORT demo_list_at_pf.
START-OF-SELECTION.
WRITE 'Basic List, Press PF5, PF6, PF7, or PF8'.
AT pf5.
PERFORM out.
AT pf6.
PERFORM out.
AT pf7.
PERFORM out.
AT pf8.
PERFORM out.
FORM out.
WRITE: 'Secondary List by PF-Key Selection',
/ 'SY-LSIND =', sy-lsind,
/ 'SY-UCOMM =', sy-ucomm.
ENDFORM.
After executing the program, the system displays the basic list. The user can press the function keys F5 , F6 , F7 , and F8 to create secondary lists. If, for example, the 14th key the user presses is F6 , the output on the displayed secondary list looks as follows:
Secondary List by PF-Key Selection
SY-LSIND = 14
SY-UCOMM = PF06
Example for AT USER-COMMAND.
REPORT demo_list_at_user_command NO STANDARD PAGE HEADING.
START-OF-SELECTION.
WRITE: 'Basic List',
/ 'SY-LSIND:', sy-lsind.
TOP-OF-PAGE.
WRITE 'Top-of-Page'.
ULINE.
TOP-OF-PAGE DURING LINE-SELECTION.
CASE sy-pfkey.
WHEN 'TEST'.
WRITE 'Self-defined GUI for Function Codes'.
ULINE.
ENDCASE.
AT LINE-SELECTION.
SET PF-STATUS 'TEST' EXCLUDING 'PICK'.
PERFORM out.
sy-lsind = sy-lsind - 1.
AT USER-COMMAND.
CASE sy-ucomm.
WHEN 'FC1'.
PERFORM out.
WRITE / 'Button FUN 1 was pressed'.
WHEN 'FC2'.
PERFORM out.
WRITE / 'Button FUN 2 was pressed'.
WHEN 'FC3'.
PERFORM out.
WRITE / 'Button FUN 3 was pressed'.
WHEN 'FC4'.
PERFORM out.
WRITE / 'Button FUN 4 was pressed'.
WHEN 'FC5'.
PERFORM out.
WRITE / 'Button FUN 5 was pressed'.
ENDCASE.
sy-lsind = sy-lsind - 1.
FORM out.
WRITE: 'Secondary List',
/ 'SY-LSIND:', sy-lsind,
/ 'SY-PFKEY:', sy-pfkey.
ENDFORM.
<b>Vendor performance report</b>
See this sample code
*"Table declarations...................................................
TABLES:
EKKO, " Purchasing Document Header
CDHDR, " Change document header
SSCRFIELDS. " Fields on selection screens
*"Selection screen elements............................................
SELECT-OPTIONS:
S_EBELN FOR EKKO-EBELN, " Purchasing Document Number
S_LIFNR FOR EKKO-LIFNR, " Vendor's account number
S_EKGRP FOR EKKO-EKGRP, " Purchasing group
S_BEDAT FOR EKKO-BEDAT, " Purchasing Document Date
S_UDATE FOR CDHDR-UDATE. " Creation date of the change
" document
*" Data declarations...................................................
Field String to hold Purchase Document Number *
DATA:
BEGIN OF FS_EBELN,
EBELN(90) TYPE C, " Purchase Document Number
ERNAM TYPE EKKO-ERNAM, " Name of Person who Created
" the Object
LIFNR TYPE EKKO-LIFNR, " Vendor's account number
EKGRP TYPE EKKO-EKGRP, " Purchasing group
BEDAT TYPE EKKO-BEDAT, " Purchasing Document Date
END OF FS_EBELN,
Field String to hold Purchase Document Header *
BEGIN OF FS_EKKO,
EBELN TYPE EKKO-EBELN, " Purchasing Document Number
ERNAM TYPE EKKO-ERNAM, " Name of Person who Created the
" Object
LIFNR TYPE EKKO-LIFNR, " Vendor's account number
EKGRP TYPE EKKO-EKGRP, " Purchasing group
BEDAT TYPE EKKO-BEDAT, " Purchasing Document Date
END OF FS_EKKO,
Field String to hold Account Number and name of the Vendor *
BEGIN OF FS_LFA1,
LIFNR TYPE LFA1-LIFNR, " Account Number of Vendor
NAME1 TYPE LFA1-NAME1, " Name1
END OF FS_LFA1,
Field String to hold Change date and the name of the user *
BEGIN OF FS_CDHDR,
OBJECTCLAS TYPE CDHDR-OBJECTCLAS, " Object Class
OBJECTID TYPE CDHDR-OBJECTID, " Object value
CHANGENR TYPE CDHDR-CHANGENR, " Document change number
USERNAME TYPE CDHDR-USERNAME, " User name
UDATE TYPE CDHDR-UDATE, " Creation date of the change
" document
END OF FS_CDHDR,
Field String to hold Change document items *
BEGIN OF FS_CDPOS,
OBJECTCLAS TYPE CDPOS-OBJECTCLAS," Object class
OBJECTID(10) TYPE C, " Object Value
CHANGENR TYPE CDPOS-CHANGENR, " Document change number
TABNAME TYPE CDPOS-TABNAME, " Table Name
FNAME TYPE CDPOS-FNAME, " Field Name
VALUE_NEW TYPE CDPOS-VALUE_NEW, " New contents of changed field
VALUE_OLD TYPE CDPOS-VALUE_OLD, " Old contents of changed field
END OF FS_CDPOS,
Field String to hold Date Element Name *
BEGIN OF FS_DATAELE,
TABNAME TYPE DD03L-TABNAME, " Table Name
FIELDNAME TYPE DD03L-FIELDNAME, " Field Name
ROLLNAME TYPE DD03L-ROLLNAME, " Data element (semantic domain)
END OF FS_DATAELE,
Field String to hold Short Text of the Date Element *
BEGIN OF FS_TEXT,
ROLLNAME TYPE DD04T-ROLLNAME, " Data element (semantic domain)
DDTEXT TYPE DD04T-DDTEXT, " Short Text Describing R/3
" Repository Objects
END OF FS_TEXT,
Field String to hold data to be displayed on the ALV grid *
BEGIN OF FS_OUTTAB,
EBELN TYPE EKKO-EBELN, " Purchasing Document Number
ERNAM TYPE EKKO-ERNAM, " Name of Person who Created the
" Object
LIFNR TYPE EKKO-LIFNR, " Vendor's account number
EKGRP TYPE EKKO-EKGRP, " Purchasing group
BEDAT TYPE EKKO-BEDAT, " Purchasing Document Date
WERKS TYPE LFA1-WERKS, " Plant
NAME1 TYPE LFA1-NAME1, " Name1
USERNAME TYPE CDHDR-USERNAME, " User name
UDATE TYPE CDHDR-UDATE, " Creation date of the change
" document
DDTEXT TYPE DD04T-DDTEXT, " Short Text Describing R/3
" Repository Objects
VALUE_NEW TYPE CDPOS-VALUE_NEW, " New contents of changed field
VALUE_OLD TYPE CDPOS-VALUE_OLD, " Old contents of changed field
END OF FS_OUTTAB,
Internal table to hold Purchase Document Number *
T_EBELN LIKE STANDARD TABLE
OF FS_EBELN,
Internal table to hold Purchase Document Header *
T_EKKO LIKE STANDARD TABLE
OF FS_EKKO,
Temp Internal table to hold Purchase Document Header *
T_EKKO_TEMP LIKE STANDARD TABLE
OF FS_EKKO,
Internal table to hold Account number and Name of the Vendor *
T_LFA1 LIKE STANDARD TABLE
OF FS_LFA1,
Internal Table to hold Change date and the name of the user *
T_CDHDR LIKE STANDARD TABLE
OF FS_CDHDR,
Internal Table to hold Change document items *
T_CDPOS LIKE STANDARD TABLE
OF FS_CDPOS,
Temp. Internal Table to hold Change document items *
T_CDPOS_TEMP LIKE STANDARD TABLE
OF FS_CDPOS,
Internal Table to hold Data Element Name *
T_DATAELE LIKE STANDARD TABLE
OF FS_DATAELE,
Temp. Internal Table to hold Data Element Name *
T_DATAELE_TEMP LIKE STANDARD TABLE
OF FS_DATAELE,
Internal Table to hold Short Text of the Date Element *
T_TEXT LIKE STANDARD TABLE
OF FS_TEXT,
Internal Table to hold data to be displayed on the ALV grid *
T_OUTTAB LIKE STANDARD TABLE
OF FS_OUTTAB.
C L A S S D E F I N I T I O N *
CLASS LCL_EVENT_HANDLER DEFINITION DEFERRED.
*" Data declarations...................................................
Work variables *
DATA:
W_EBELN TYPE EKKO-EBELN, " Purchasing Document Number
W_LIFNR TYPE EKKO-LIFNR, " Vendor's account number
W_EKGRP TYPE EKKO-EKGRP, " Purchasing group
W_VALUE TYPE EKKO-EBELN, " Reflected Value
W_SPACE VALUE ' ', " Space
W_FLAG TYPE I, " Flag Variable
W_VARIANT TYPE DISVARIANT, " Variant
*--- ALV Grid
W_GRID TYPE REF TO CL_GUI_ALV_GRID,
*--- Event Handler
W_EVENT_CLICK TYPE REF TO LCL_EVENT_HANDLER,
*--- Field catalog table
T_FIELDCAT TYPE LVC_T_FCAT.
AT SELECTION-SCREEN EVENT *
AT SELECTION-SCREEN ON S_EBELN.
Subroutine to validate Purchase Document Number.
PERFORM VALIDATE_PD_NUM.
AT SELECTION-SCREEN ON S_LIFNR.
Subroutine to validate Vendor Number.
PERFORM VALIDATE_VEN_NUM.
AT SELECTION-SCREEN ON S_EKGRP.
Subroutine to validate Purchase Group.
PERFORM VALIDATE_PUR_GRP.
START-OF-SELECTION EVENT *
START-OF-SELECTION.
Subroutine to select all Purchase orders.
PERFORM SELECT_PO.
CHECK W_FLAG EQ 0.
Subroutine to select Object values.
PERFORM SELECT_OBJ_ID.
CHECK W_FLAG EQ 0.
Subroutine to select Changed values.
PERFORM SELECT_CHANGED_VALUE.
CHECK W_FLAG EQ 0.
Subroutine to Select Purchase Orders.
PERFORM SELECT_PUR_DOC.
Subroutine to select Vendor Details.
PERFORM SELECT_VENDOR.
Subroutine to select Text for the Changed values.
PERFORM DESCRIPTION.
END-OF-SELECTION EVENT *
END-OF-SELECTION.
IF NOT T_EKKO IS INITIAL.
Subroutine to populate the Output Table.
PERFORM FILL_OUTTAB.
Subroutine to build Field Catalog.
PERFORM PREPARE_FIELD_CATALOG CHANGING T_FIELDCAT.
CALL SCREEN 100.
ENDIF. " IF NOT T_EKKO...
CLASS LCL_EVENT_HANDLER DEFINITION
Defining Class which handles events
CLASS LCL_EVENT_HANDLER DEFINITION .
PUBLIC SECTION .
METHODS:
HANDLE_HOTSPOT_CLICK
FOR EVENT HOTSPOT_CLICK OF CL_GUI_ALV_GRID
IMPORTING E_ROW_ID E_COLUMN_ID.
ENDCLASS. " LCL_EVENT_HANDLER DEFINITION
CLASS LCL_EVENT_HANDLER IMPLEMENTATION
Implementing the Class which can handle events
CLASS LCL_EVENT_HANDLER IMPLEMENTATION .
*---Handle Double Click
METHOD HANDLE_HOTSPOT_CLICK .
Subroutine to get the HotSpot Cell information.
PERFORM GET_CELL_INFO.
SET PARAMETER ID 'BES' FIELD W_VALUE.
CALL TRANSACTION 'ME23N'.
ENDMETHOD. " HANDLE_HOTSPOT_CLICK
ENDCLASS. " LCL_EVENT_HANDLER
*& Module STATUS_0100 OUTPUT
PBO Event
MODULE STATUS_0100 OUTPUT.
SET PF-STATUS 'OOPS'.
SET TITLEBAR 'TIT'.
Subroutine to fill the Variant Structure
PERFORM FILL_VARIANT.
IF W_GRID IS INITIAL.
CREATE OBJECT W_GRID
EXPORTING
I_SHELLSTYLE = 0
I_LIFETIME =
I_PARENT = CL_GUI_CONTAINER=>SCREEN0
I_APPL_EVENTS =
I_PARENTDBG =
I_APPLOGPARENT =
I_GRAPHICSPARENT =
I_NAME =
I_FCAT_COMPLETE = SPACE
EXCEPTIONS
ERROR_CNTL_CREATE = 1
ERROR_CNTL_INIT = 2
ERROR_CNTL_LINK = 3
ERROR_DP_CREATE = 4
OTHERS = 5.
IF SY-SUBRC <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF. " IF SY-SUBRC <> 0
CALL METHOD W_GRID->SET_TABLE_FOR_FIRST_DISPLAY
EXPORTING
I_BUFFER_ACTIVE =
I_BYPASSING_BUFFER =
I_CONSISTENCY_CHECK =
I_STRUCTURE_NAME =
IS_VARIANT = W_VARIANT
I_SAVE = 'A'
I_DEFAULT = 'X'
IS_LAYOUT =
IS_PRINT =
IT_SPECIAL_GROUPS =
IT_TOOLBAR_EXCLUDING =
IT_HYPERLINK =
IT_ALV_GRAPHICS =
IT_EXCEPT_QINFO =
IR_SALV_ADAPTER =
CHANGING
IT_OUTTAB = T_OUTTAB
IT_FIELDCATALOG = T_FIELDCAT
IT_SORT =
IT_FILTER =
EXCEPTIONS
INVALID_PARAMETER_COMBINATION = 1
PROGRAM_ERROR = 2
TOO_MANY_LINES = 3
OTHERS = 4
IF SY-SUBRC <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF. " IF SY-SUBRC <> 0.
ENDIF. " IF W_GRID IS INITIAL
CREATE OBJECT W_EVENT_CLICK.
SET HANDLER W_EVENT_CLICK->HANDLE_HOTSPOT_CLICK FOR W_GRID.
ENDMODULE. " STATUS_0100 OUTPUT
*& Module USER_COMMAND_0100 INPUT
PAI Event
MODULE USER_COMMAND_0100 INPUT.
CASE SY-UCOMM.
WHEN 'BACK'.
LEAVE TO SCREEN 0.
WHEN 'EXIT'.
LEAVE PROGRAM.
WHEN 'CANCEL'.
LEAVE TO SCREEN 0.
ENDCASE.
ENDMODULE. " USER_COMMAND_0100 INPUT
*& Form PREPARE_FIELD_CATALOG
Subroutine to build the Field catalog
<--P_T_FIELDCAT Field Catalog Table
FORM PREPARE_FIELD_CATALOG CHANGING PT_FIELDCAT TYPE LVC_T_FCAT .
DATA LS_FCAT TYPE LVC_S_FCAT.
Purchasing group...
LS_FCAT-FIELDNAME = 'EKGRP'.
LS_FCAT-REF_TABLE = 'EKKO'.
LS_FCAT-INTTYPE = 'C'.
LS_FCAT-OUTPUTLEN = '10'.
APPEND LS_FCAT TO PT_FIELDCAT.
CLEAR LS_FCAT.
Purchasing Document Number...
LS_FCAT-FIELDNAME = 'EBELN'.
LS_FCAT-REF_TABLE = 'EKKO' .
LS_FCAT-EMPHASIZE = 'C411'.
LS_FCAT-INTTYPE = 'C'.
LS_FCAT-OUTPUTLEN = '10'.
LS_FCAT-HOTSPOT = 'X'.
APPEND LS_FCAT TO PT_FIELDCAT .
CLEAR LS_FCAT .
Name of Person who Created the Object...
LS_FCAT-FIELDNAME = 'ERNAM'.
LS_FCAT-REF_TABLE = 'EKKO'.
LS_FCAT-OUTPUTLEN = '15' .
APPEND LS_FCAT TO PT_FIELDCAT.
CLEAR LS_FCAT.
Purchasing Document Date...
LS_FCAT-FIELDNAME = 'BEDAT'.
LS_FCAT-REF_TABLE = 'EKKO'.
LS_FCAT-INTTYPE = 'C'.
LS_FCAT-OUTPUTLEN = '10'.
APPEND LS_FCAT TO PT_FIELDCAT.
CLEAR LS_FCAT.
Vendor's account number...
LS_FCAT-FIELDNAME = 'LIFNR'.
LS_FCAT-REF_TABLE = 'EKKO'.
LS_FCAT-INTTYPE = 'C'.
LS_FCAT-OUTPUTLEN = '10'.
APPEND LS_FCAT TO PT_FIELDCAT.
CLEAR LS_FCAT.
Account Number of Vendor or Creditor...
LS_FCAT-FIELDNAME = 'NAME1'.
LS_FCAT-REF_TABLE = 'LFA1'.
LS_FCAT-INTTYPE = 'C'.
LS_FCAT-OUTPUTLEN = '10'.
LS_FCAT-COLTEXT = 'Vendor Name'(001).
LS_FCAT-SELTEXT = 'Vendor Name'(001).
APPEND LS_FCAT TO PT_FIELDCAT.
CLEAR LS_FCAT.
Creation date of the change document...
LS_FCAT-FIELDNAME = 'UDATE'.
LS_FCAT-REF_TABLE = 'CDHDR'.
LS_FCAT-INTTYPE = 'C'.
LS_FCAT-OUTPUTLEN = '10'.
LS_FCAT-COLTEXT = 'Change Date'(002).
LS_FCAT-SELTEXT = 'Change Date'(002).
APPEND LS_FCAT TO PT_FIELDCAT.
CLEAR LS_FCAT.
User name of the person responsible in change document...
LS_FCAT-FIELDNAME = 'USERNAME'.
LS_FCAT-REF_TABLE = 'CDHDR'.
LS_FCAT-INTTYPE = 'C'.
LS_FCAT-OUTPUTLEN = '10'.
LS_FCAT-COLTEXT = 'Modified by'(003).
LS_FCAT-SELTEXT = 'Modified by'(003).
APPEND LS_FCAT TO PT_FIELDCAT.
CLEAR LS_FCAT.
Short Text Describing R/3 Repository Objects...
LS_FCAT-FIELDNAME = 'DDTEXT'.
LS_FCAT-REF_TABLE = 'DD04T'.
LS_FCAT-INTTYPE = 'C'.
LS_FCAT-OUTPUTLEN = '15'.
APPEND LS_FCAT TO PT_FIELDCAT.
CLEAR LS_FCAT.
Old contents of changed field...
LS_FCAT-FIELDNAME = 'VALUE_OLD'.
LS_FCAT-REF_TABLE = 'CDPOS'.
LS_FCAT-INTTYPE = 'C'.
LS_FCAT-OUTPUTLEN = '12'.
APPEND LS_FCAT TO PT_FIELDCAT.
CLEAR LS_FCAT.
New contents of changed field...
LS_FCAT-FIELDNAME = 'VALUE_NEW'.
LS_FCAT-REF_TABLE = 'CDPOS'.
LS_FCAT-INTTYPE = 'C'.
LS_FCAT-OUTPUTLEN = '12'.
APPEND LS_FCAT TO PT_FIELDCAT.
CLEAR LS_FCAT.
ENDFORM. " PREPARE_FIELD_CATALOG
*& Form SELECT_PO
Subroutine to select all the Purchase Orders
There are no interface parameters to be passed to this subroutine.
FORM SELECT_PO .
SELECT EBELN " Purchasing Document Number
ERNAM " Name of Person who Created
" the Object
LIFNR " Vendor's account number
EKGRP " Purchasing group
BEDAT " Purchasing Document Date
FROM EKKO
PACKAGE SIZE 10000
APPENDING TABLE T_EBELN
WHERE EBELN IN S_EBELN
AND BEDAT IN S_BEDAT.
ENDSELECT.
IF SY-SUBRC NE 0.
W_FLAG = 1.
MESSAGE S401(M8).
ENDIF. " IF SY-SUBRC NE 0
ENDFORM. " SELECT_PO
*& Form SELECT_OBJ_ID
Subroutine to select Object ID
There are no interface parameters to be passed to this subroutine.
FORM SELECT_OBJ_ID .
IF NOT T_EBELN IS INITIAL.
SELECT OBJECTCLAS " Object Class
OBJECTID " Object value
CHANGENR " Document change number
USERNAME " User name
UDATE " Creation date
FROM CDHDR
INTO TABLE T_CDHDR
FOR ALL ENTRIES IN T_EBELN
WHERE OBJECTID EQ T_EBELN-EBELN
AND UDATE IN S_UDATE
AND TCODE IN ('ME21N','ME22N','ME23N').
ENDSELECT.
IF SY-SUBRC NE 0.
W_FLAG = 1.
MESSAGE S833(M8) WITH 'Header Not Found'(031).
ENDIF. " IF SY-SUBRC NE 0.
ENDIF. " IF NOT T_EBELN IS INITIAL
ENDFORM. " SELECT_OBJ_ID
*& Form SELECT_CHANGED_VALUE
Subroutine to select Changed Values
There are no interface parameters to be passed to this subroutine.
FORM SELECT_CHANGED_VALUE .
IF NOT T_CDHDR IS INITIAL.
SELECT OBJECTCLAS " Object class
OBJECTID " Object value
CHANGENR " Document change number
TABNAME " Table Name
FNAME " Field Name
VALUE_NEW " New contents of changed field
VALUE_OLD " Old contents of changed field
FROM CDPOS
PACKAGE SIZE 10000
APPENDING TABLE T_CDPOS
FOR ALL ENTRIES IN T_CDHDR
WHERE OBJECTCLAS EQ T_CDHDR-OBJECTCLAS
AND OBJECTID EQ T_CDHDR-OBJECTID
AND CHANGENR EQ T_CDHDR-CHANGENR.
ENDSELECT.
IF SY-SUBRC NE 0.
W_FLAG = 1.
MESSAGE S833(M8) WITH 'Item Not Found'(032).
ENDIF. " IF SY-SUBRC NE 0.
ENDIF. " IF NOT T_CDHDR IS INITIAL
T_CDPOS_TEMP[] = T_CDPOS[].
ENDFORM. " SELECT_CHANGED_VALUE
*& Form SELECT_PUR_DOC
Subroutine to select Purchase Order Details
There are no interface parameters to be passed to this subroutine.
FORM SELECT_PUR_DOC .
IF NOT T_CDPOS IS INITIAL.
SORT T_EBELN BY EBELN.
LOOP AT T_CDPOS INTO FS_CDPOS.
READ TABLE T_EBELN INTO FS_EBELN WITH KEY EBELN =
FS_CDPOS-OBJECTID BINARY SEARCH.
IF SY-SUBRC NE 0.
DELETE TABLE T_EBELN FROM FS_EBELN.
ENDIF. " IF SY-SUBRC NE 0.
ENDLOOP. " LOOP AT T_CDPOS...
LOOP AT T_EBELN INTO FS_EBELN.
MOVE FS_EBELN-EBELN TO FS_EKKO-EBELN.
MOVE FS_EBELN-ERNAM TO FS_EKKO-ERNAM.
MOVE FS_EBELN-LIFNR TO FS_EKKO-LIFNR.
MOVE FS_EBELN-EKGRP TO FS_EKKO-EKGRP.
MOVE FS_EBELN-BEDAT TO FS_EKKO-BEDAT.
APPEND FS_EKKO TO T_EKKO.
ENDLOOP. " LOOP AT T_EBELN...
T_EKKO_TEMP[] = T_EKKO[].
ENDIF. " IF NOT T_CDPOS IS INITIAL
ENDFORM. " SELECT_PUR_DOC
*& Form SELECT_VENDOR
Subroutine to select Vendor details
There are no interface parameters to be passed to this subroutine.
FORM SELECT_VENDOR .
IF NOT T_EKKO IS INITIAL.
SORT T_EKKO_TEMP BY LIFNR.
DELETE ADJACENT DUPLICATES FROM T_EKKO_TEMP COMPARING LIFNR.
SELECT LIFNR " Account Number of Vendor or
" Creditor
NAME1 " Name 1
FROM LFA1
INTO TABLE T_LFA1
FOR ALL ENTRIES IN T_EKKO_TEMP
WHERE LIFNR EQ T_EKKO_TEMP-LIFNR.
IF SY-SUBRC NE 0.
MESSAGE S002(M8) WITH 'Master Details'(033).
ENDIF. " IF SY-SUBRC NE 0.
ENDIF. " IF NOT T_EKKO IS INITIAL
ENDFORM. " SELECT_VENDOR
*& Form DESCRIPTION
Subroutine to get the description
There are no interface parameters to be passed to this subroutine.
FORM DESCRIPTION .
IF NOT T_CDPOS IS INITIAL.
SORT T_CDPOS_TEMP BY TABNAME FNAME.
DELETE ADJACENT DUPLICATES FROM T_CDPOS_TEMP COMPARING TABNAME FNAME
SELECT TABNAME " Table Name
FIELDNAME " Field Name
ROLLNAME " Data element
FROM DD03L
INTO TABLE T_DATAELE
FOR ALL ENTRIES IN T_CDPOS_TEMP
WHERE TABNAME EQ T_CDPOS_TEMP-TABNAME
AND FIELDNAME EQ T_CDPOS_TEMP-FNAME.
IF NOT T_DATAELE IS INITIAL.
T_DATAELE_TEMP[] = T_DATAELE[].
SORT T_DATAELE_TEMP BY ROLLNAME.
DELETE ADJACENT DUPLICATES FROM T_DATAELE_TEMP COMPARING ROLLNAME.
SELECT ROLLNAME " Data element
DDTEXT " Short Text Describing R/3
" Repository Objects
FROM DD04T
INTO TABLE T_TEXT
FOR ALL ENTRIES IN T_DATAELE_TEMP
WHERE ROLLNAME EQ T_DATAELE_TEMP-ROLLNAME
AND DDLANGUAGE EQ SY-LANGU.
IF SY-SUBRC NE 0.
EXIT.
ENDIF. " IF SY-SUBRC NE 0.
ENDIF. " IF NOT T_DATAELE IS INITIAL.
ENDIF. " IF NOT T_CDPOS IS INITIAL.
ENDFORM. " DESCRIPTION
*& Form FILL_OUTTAB
Subroutine to populate the Outtab
There are no interface parameters to be passed to this subroutine.
FORM FILL_OUTTAB .
SORT T_CDHDR BY OBJECTCLAS OBJECTID CHANGENR.
SORT T_EKKO BY EBELN.
SORT T_LFA1 BY LIFNR.
SORT T_DATAELE BY TABNAME FIELDNAME.
SORT T_TEXT BY ROLLNAME.
LOOP AT T_CDPOS INTO FS_CDPOS.
READ TABLE T_CDHDR INTO FS_CDHDR WITH KEY
OBJECTCLAS = FS_CDPOS-OBJECTCLAS
OBJECTID = FS_CDPOS-OBJECTID
CHANGENR = FS_CDPOS-CHANGENR
BINARY SEARCH.
IF SY-SUBRC EQ 0.
MOVE FS_CDHDR-USERNAME TO FS_OUTTAB-USERNAME.
MOVE FS_CDHDR-UDATE TO FS_OUTTAB-UDATE.
READ TABLE T_EKKO INTO FS_EKKO WITH KEY
EBELN = FS_CDHDR-OBJECTID
BINARY SEARCH.
IF SY-SUBRC EQ 0.
MOVE FS_EKKO-EBELN TO FS_OUTTAB-EBELN.
MOVE FS_EKKO-ERNAM TO FS_OUTTAB-ERNAM.
MOVE FS_EKKO-LIFNR TO FS_OUTTAB-LIFNR.
MOVE FS_EKKO-EKGRP TO FS_OUTTAB-EKGRP.
MOVE FS_EKKO-BEDAT TO FS_OUTTAB-BEDAT.
READ TABLE T_LFA1 INTO FS_LFA1 WITH KEY
LIFNR = FS_EKKO-LIFNR
BINARY SEARCH.
IF SY-SUBRC EQ 0.
MOVE FS_LFA1-NAME1 TO FS_OUTTAB-NAME1.
ENDIF. " IF SY-SUBRC EQ 0.
ENDIF. " IF SY-SUBRC EQ 0.
ENDIF. " IF SY-SUBRC EQ 0.
MOVE FS_CDPOS-VALUE_NEW TO FS_OUTTAB-VALUE_NEW.
MOVE FS_CDPOS-VALUE_OLD TO FS_OUTTAB-VALUE_OLD.
READ TABLE T_DATAELE INTO FS_DATAELE WITH KEY
TABNAME = FS_CDPOS-TABNAME
FIELDNAME = FS_CDPOS-FNAME
BINARY SEARCH.
IF SY-SUBRC EQ 0.
READ TABLE T_TEXT INTO FS_TEXT WITH KEY
ROLLNAME = FS_DATAELE-ROLLNAME
BINARY SEARCH.
IF SY-SUBRC EQ 0.
MOVE FS_TEXT-DDTEXT TO FS_OUTTAB-DDTEXT.
ENDIF. " IF SY-SUBRC EQ 0.
ENDIF. " IF SY-SUBRC EQ 0.
APPEND FS_OUTTAB TO T_OUTTAB.
CLEAR FS_OUTTAB.
ENDLOOP.
ENDFORM. " FILL_OUTTAB
*& Form GET_CELL_INFO
Subroutine to get the Cell Information
--> W_VALUE Holds the value of Hotspot clicked
FORM GET_CELL_INFO .
CALL METHOD W_GRID->GET_CURRENT_CELL
IMPORTING
E_ROW =
E_VALUE = W_VALUE
E_COL =
ES_ROW_ID =
ES_COL_ID =
ES_ROW_NO =
ENDFORM. " GET_CELL_INFO
*& Form VALIDATE_PD_NUM
Subroutine to validate Purchase Document Number
There are no interface parameters to be passed to this subroutine.
FORM VALIDATE_PD_NUM .
IF NOT S_EBELN[] IS INITIAL.
SELECT EBELN " Purchase Document Number
FROM EKKO
INTO W_EBELN
UP TO 1 ROWS
WHERE EBELN IN S_EBELN.
ENDSELECT.
IF SY-SUBRC NE 0.
CLEAR SSCRFIELDS-UCOMM.
MESSAGE E717(M8).
ENDIF. " IF SY-SUBRC NE 0
ENDIF. " IF NOT S_EBELN[]...
ENDFORM. " VALIDATE_PD_NUM
*& Form VALIDATE_VEN_NUM
Subroutine to validate Vendor Number
There are no interface parameters to be passed to this subroutine.
FORM VALIDATE_VEN_NUM .
IF NOT S_LIFNR[] IS INITIAL.
SELECT LIFNR " Vendor Number
FROM LFA1
INTO W_LIFNR
UP TO 1 ROWS
WHERE LIFNR IN S_LIFNR.
ENDSELECT.
IF SY-SUBRC NE 0.
CLEAR SSCRFIELDS-UCOMM.
MESSAGE E002(M8) WITH W_SPACE.
ENDIF. " IF SY-SUBRC NE 0
ENDIF. " IF NOT S_LIFNR[]...
ENDFORM. " VALIDATE_VEN_NUM
*& Form VALIDATE_PUR_GRP
Subroutine to validate the Purchase Group
There are no interface parameters to be passed to this subroutine.
FORM VALIDATE_PUR_GRP .
IF NOT S_EKGRP[] IS INITIAL.
SELECT EKGRP " Purchase Group
FROM T024
INTO W_EKGRP
UP TO 1 ROWS
WHERE EKGRP IN S_EKGRP.
ENDSELECT.
IF SY-SUBRC NE 0.
CLEAR SSCRFIELDS-UCOMM.
MESSAGE E622(M8) WITH W_SPACE.
ENDIF. " IF SY-SUBRC NE 0
ENDIF. " IF NOT S_EKFRP[]...
ENDFORM. " VALIDATE_PUR_GRP
*& Form FILL_VARIANT
Subroutine to fill the Variant Structure
There are no interface parameters to be passed to this subroutine
FORM FILL_VARIANT .
Filling the Variant structure
W_VARIANT-REPORT = SY-REPID.
W_VARIANT-USERNAME = SY-UNAME.
ENDFORM. " FILL_VARIANT
<b>Reward if usefull</b>

2K8 - Best practice for setting the DNS server list on a DC/DNS server for an interface

We have been referencing the article
"DNS: DNS servers on <adapter name> should include their own IP addresses on their interface lists of DNS servers"
http://technet.microsoft.com/en-us/library/dd378900%28WS.10%29.aspx but there are some parts that are a bit confusing. In particular is this statement
"The inclusion of its own IP address in the list of DNS servers improves performance and increases availability of DNS servers. However, if the DNS server is also a domain
controller and it points only to itself for name resolution, it can become an island and fail to replicate with other domain controllers. For this reason, use caution when configuring the loopback address on an adapter if the server is also a domain controller.
The loopback address should be configured only as a secondary or tertiary DNS server on a domain controller.”
The paragraph switches from using the term "its own IP address" to "loopback" address. This is confusing becasuse technically they are not the same. Loppback addresses are 127.0.0.1 through 127.255.255.255. The resolution section then
goes on and adds the "loopback address" 127.0.0.1 to the list of DNS servers for each interface.
In the past we always setup DCs to use their own IP address as the primary DNS server, not 127.0.0.1. Based on my experience and reading the article I am under the impression we could use the following setup.
Primary DNS: Locally assigned IP of the DC (i.e. 192.168.1.5)
Secondary DNS: The assigned IP of another DC (i.e. 192.168.1.6)
Tertiary DNS: 127.0.0.1
I guess the secondary and tertiary addresses could be swapped based on the article. Is there a document that provides clearer guidance on how to setup the DNS server list properly on Windows 2008 R2 DC/DNS servers? I have seen some other discussions
that talk about the pros and cons of using another DC/DNS as the Primary. MS should have clear guidance on this somewhere.

Actually, my suggestion, which seems to be the mostly agreed method, is:
Primary DNS: Locally assigned IP of the DC (i.e. 192.168.1.5)
Secondary DNS: The assigned IP of another DC (i.e. 192.168.1.6)
Tertiary DNS: empty
The tertiary more than likely won't be hit, (besides it being superfluous and the list will reset back to the first one) due to the client side resolver algorithm time out process, as I mentioned earlier. Here's a full explanation on how
it works and why:
This article discusses:
WINS NetBIOS, Browser Service, Disabling NetBIOS, & Direct Hosted SMB (DirectSMB).
The DNS Client Side Resolver algorithm.
If one DC or DNS goes down, does a client logon to another DC?
DNS Forwarders Algorithm and multiple DNS addresses (if you've configured more than one forwarders)
Client side resolution process chart
http://msmvps.com/blogs/acefekay/archive/2009/11/29/dns-wins-netbios-amp-the-client-side-resolver-browser-service-disabling-netbios-direct-hosted-smb-directsmb-if-one-dc-is-down-does-a-client-
logon-to-another-dc-and-dns-forwarders-algorithm.aspx
DNS
Client side resolver service
http://technet.microsoft.com/en-us/library/cc779517.aspx
The DNS Client Service Does Not Revert to Using the First Server in the List in Windows XP
http://support.microsoft.com/kb/320760
Ace Fekay
MVP, MCT, MCITP EA, MCTS Windows 2008 & Exchange 2007 & Exchange 2010, Exchange 2010 Enterprise Administrator, MCSE & MCSA 2003/2000, MCSA Messaging 2003
Microsoft Certified Trainer
Microsoft MVP - Directory Services
Complete List of Technical Blogs: http://www.delawarecountycomputerconsulting.com/technicalblogs.php
This posting is provided AS-IS with no warranties or guarantees and confers no rights.
I agree with this proposed solution as well:
Primary DNS: Locally assigned IP of the DC (i.e. 192.168.1.5)
Secondary DNS: The assigned IP of another DC (i.e. 192.168.1.6)
Tertiary DNS: empty
One thing to note, in this configuration the Best Practice Analyzer will throw the error:
The network adapter Local Area Connection 2 does not list the loopback IP address as a DNS server, or it is configured as the first entry.
Even if you add the loopback address as a Tertiary DNS address the error will still appear. The only way I've seen this error eliminated is to add the loopback address as the second entry in DNS, so:
Primary DNS: The assigned IP of another DC (i.e. 192.168.1.6)
Secondary DNS: 127.0.0.1
Tertiary DNS: empty
I'm not comfortable not having the local DC/DNS address listed so I'm going with the solution Ace offers.
Opinion?

How to exclude synchronous interfaces from component based message alerting

Hi Pi experts,
We are configuiring Alerts in PI 7.3 single stack.If we have 'n'number of interfaces, and if we configured general alerts for all.How to exclude synchronous interfaces in that.Alerting is for asynchronous interfaces only.How to do that.
Please advice on this.
Regards
Suneel

Hello,
>>What are your approaches regarding this requirement in the context of java-only?
I would suggest you to schedule jobs like this:
Customize Alerts Using Job in PI 7.31/PO
>> alerts are consumed according to the given interval and not in "real time" when error occurs, today solution using BADI is "real time" - if possible I would prefer "real time" solution
Check this:
Michal's PI tips: How to trigger an alert for Component Based Message Alerts (CBMA) via "API" ?
>>an separate service determine the actual alert count would be helpful to provide the correct value for maxAlerts, this have to be called beforehand
I haven't tried it but i think u can do that, since these consumers are nothing but JMS queues only so i think there will be a method to read number of alert counts.
>>In history I saw emails generated by the standard alert consumer which only contain details for the first alert, in my case I need details especially the message id for all errorneous messages
If ur max alert parameter is greater than 1 then u should see multiple alert text (along with message id and other details) in ur email message.
Thanks
Amit Srivastava

VLAN for WLC interface (ISE Policies Based on SSID)

Similar Messages

Maybe you are looking for