VLAN RUNNING Config fetch Failed
Hi;
I have running Ciscowork LSM 3.2 with RME Ver 4.3 and Running SNMP V3 on all device. Out of 134 device 12-13 shows me Vlan running Config fetch failed. Please also find the dcmaservice.log in attachment.
I already verify the Crediential number or times, I can access the devices from SSH and Telnet, on Cisco works RME shows Running and Startup Config success while VLAN Running Config fetch failed. and on some device it show following
Protocol and Platforms passed = TELNET , RMEIOS
trying for Telnet
Failed to get CmdSvc from DeviceContext....
Thanks,
Best regards;
Shoaib Ahmed
HI Shoaib,
Try ssh\telnet into the device manually and issue the command copy flash:vlan.dat tftp: and
enter the IP address of the LMS server? Does it work? If that works fine, try to increase
the tftp timeout.
This can be done under RME> Admin> System Preferences> RME Device Attributes.
if it failed with an Error as below :
%Error opening tftp: ............
Then check if there any firewall in between these device and LMS blocking TFTP as TFTP is the only protocal
that fetch the vlan.dat from the device.
Thanks--
Afroj
Similar Messages
-
The error message below is from a device that I am trying to sync a configuration, device is using TACACS:
RUNNING
CM0151 PRIMARY RUNNING config fetch failed for ROUTER Cause: TELNET: Failed to establish a Telnet connection to
X.X.X.X Cause connection refused.
SSH: Same message as aboove except authentication failed on device 3 times.
ACTION: Check if protocal is supported and required on device package is installed.The error about authentication is usually correct. Go to Common Services > Device and Credentials > Device Management, select the device in question, then export the credentials. Look at the CSV export, and take the username and password, and try to SSH to the device from the LMS server. Verify you can login and get into enable mode using the same credentials in DCR.
-
LMS 4: VLAN config fetch failing for all devices
LMS 4.0.1, standalone on W2K8 R2, new install
Vlan config fetch is failing for all devices. If I attempt to put a vlan.dat file in tftpboot and then manually copy a vlan.dat file from a device, the following is returned:
TFTP: error code 2 received - 16739
%Error opening tftp://server_name/vlan.dat (Permission denied)
The Windows application logs ont the server log this:
Log Name: Application
Source: CRMtftp
Date: 6/15/2011 2:07:49 PM
Event ID: 3
Task Category: None
Level: Error
Keywords: Classic
User: N/A
Computer: server_name
Description:
GetEffectiveRightsFromAcl failed: Overlapped I/O operation is in progress.
(997)
I tried restarting crmtftp, but no luck. Any ideas what may be causing this?
-JeffI have the same issue with a freshly installed 4.2 version now:
Log Name: Application
Source: CRMtftp
Date: 2/24/2012 12:30:50 PM
Event ID: 3
Task Category: None
Level: Error
Keywords: Classic
User: N/A
Computer: srvwienlms.nts.local
Description:
GetNamedSecurityInfo failed failed: The operation completed successfully.
(0)
I will also open a TAC case, lets see if we still have to stick with a3.x TFTP binary...
br.herwig -
Cisco VG248 config archive fails
I beleive in the past these devices could not be managed bij RME config management, but now it says in the supported device table:
The following features are supported:
Network Topology Layer 2 Services
Fault Management
Inventory Collection
Configuration Deploy Protocols: TELNET, SSH, TFTP, RCP
Configuration Fetch Protocols: TELNET, SSH, TFTP, RCP
The password and enable pasword are correct and simply work when I try a telnet from the server.
The gui is not CLI but menu driven.
RME just says:
TELNET: Failed to establish TELNET connection to 10.1.1.7 - Cause: Authentication failed on device 3 times. PRIMARY-RUNNING config Fetch Operation failed for TFTP. Could not detect SSH protocols running on the device.
What can be wrong?
Cheers,
MichelHi Michel,
Thanks for the screenshot. I found that you now have customized prompts in tacacspropmt.ini file.
[ Fri Aug 26 11:30:26 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Checking for user prompt : Username: *
[ Fri Aug 26 11:30:26 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Checking for user prompt : username: *
[ Fri Aug 26 11:30:26 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Checking for user prompt : login: *
[ Fri Aug 26 11:30:26 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Checking for user prompt : Username:*
[ Fri Aug 26 11:30:26 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Checking for user prompt : username:*
[ Fri Aug 26 11:30:26 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Checking for user prompt : login:*
[ Fri Aug 26 11:30:26 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Checking for user prompt : username:*
[ Fri Aug 26 11:30:26 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Checking for user prompt : Username:*
[ Fri Aug 26 11:30:26 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Checking for password prompt : Password: *
and look like RME is able to login to device as well now :-
[ Fri Aug 26 11:29:11 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,State traversal for telnet login:
[ Fri Aug 26 11:29:11 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Connected
[ Fri Aug 26 11:29:11 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Verify
[ Fri Aug 26 11:29:11 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Success
[ Fri Aug 26 11:29:11 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,login succeeded
Kindly run the credentials verification job and let me know the results --> Is the device still failing for the telnet and enable password ?
Also navigate to CSCOpx\objects\cmf\data and uncomment the following on file cmdsvc.properties like this :-
InitialTransportTimeout=50000
TransportTimeout=90000
TuneSleepMillis=3000
DelayAfterConnect=1000
LMS was not able to login to device successfully yet or it could be timeout issue. After this LMS try to get the config of the device using SNMP and tftp, but look like tftp is blocked in network too, See this :-
[ Fri Aug 26 11:31:04 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.pkgs.SharedDcmaGeneric.transport.GenericTftpOperator,fetchConfig,170,Initialized SNMP
[ Fri Aug 26 11:31:04 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.pkgs.LibCommon.snmp.ConfigCopyMib,copyFromRunning,119,FileName= 20110826113104185-10.13.192.9.cfg tftpDir = User = password = serverAddr = 10.1.3.156
[ Fri Aug 26 11:31:04 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.pkgs.LibCommon.snmp.ConfigCopyMib,copyFromRunning,130,Cannot create variable binding list com.cisco.nm.lib.snmp.lib.SnmpException: SnmpResponseGenErr on 10.13.192.9 while performing SnmpSet at index = 0
[ Fri Aug 26 11:31:04 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.pkgs.SharedDcmaGeneric.transport.GenericTftpOperator,fetchConfig,182,Fetch completed
[ Fri Aug 26 11:31:04 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.pkgs.SharedDcmaGeneric.transport.GenericTftpOperator,fetchConfig,190,PRIMARY-RUNNING config Fetch Operation failed
[ Fri Aug 26 11:31:04 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.pkgs.SharedDcmaGeneric.transport.GenericTftpOperator,fetchConfig,196,PRIMARY-RUNNING config Fetch Operation failed for TFTP. java.lang.Exception: PRIMARY-RUNNING config Fetch Operation failed for TFTP.
at com.cisco.nm.xms.xdi.pkgs.SharedDcmaGeneric.transport.GenericTftpOperator.fetchConfig(GenericTftpOperator.java:192)
at com.cisco.nm.xms.xdi.pkgs.SharedDcmaGeneric.transport.GenericTftpOperator.fetchConfig(GenericTftpOperator.java:93)
at com.cisco.nm.xms.xdi.pkgs.LibDcma.persistor.SimpleFetchOperation.performOperation(SimpleFetchOperation.java:61)
at com.cisco.nm.xms.xdi.pkgs.LibDcma.persistor.ConfigOperation.doConfigOperation(ConfigOperation.java:111)
at com.cisco.nm.xms.xdi.pkgs.SharedDcmaGeneric.transport.GenericConfigOperator.fetchConfig(GenericConfigOperator.java:72)
at com.cisco.nm.rmeng.dcma.configmanager.ConfigManager.updateArchiveForDevice(ConfigManager.java:1317)
at com.cisco.nm.rmeng.dcma.configmanager.ConfigManager.performCollection(ConfigManager.java:3307)
at com.cisco.nm.rmeng.dcma.configmanager.CfgUpdateThread.run(CfgUpdateThread.java:27)
So, in summary, kindly edit the cmdsvc.properties file and make the changes as I suggested . Also let me know the results of the credentials verification job and run the packet capture while running the credentials verification job.
Many Thanks,
Gaganjeet -
I have devices loaded but new devices keep getting this error "Authentication failed on device 3 times. Failed to detect SSH version running on the device. PRIMARY-STARTUP config Fetch Operation failed for TFTP" - which trying to get configurations. I am using LMS 3.0.1
I tried to TELNET on devices via Putty port 22 no good. Please help?
Name Version License Status Size CiscoWorks Common Services 3.1.1 Licensed Not applicable Campus Manager 5.0.3 Purchased 1500 CiscoView 6.1.7 Licensed Not applicable CiscoWorks Assistant 1.0.1 Licensed Not applicable Device Fault Manager 3.0.3 Purchased 1500 Internetwork Performance Monitor 4.0.1 Purchased 1500 Integration Utility 1.7.1 Licensed Not applicable LMS Portal 1.0.1 Licensed Not applicable Resource Manager Essentials 4.1.1 Purchased 1500Showing 1-1 of 1 records
Go to page:
of 1 pages
Device Name
SysObjectID
Model
Device Status
Inventory Status
Inventory Last Updated Time
Config Status
Config Last Updated Time
1.
R2020012_01
.1.3.6.1.4.1.9.1.576
Cisco 2811 Integrated Services Router
Normal
Success
Jan 13 2011 10:43:49 EST
Failed
Jan 13 2011 10:37:24 EST
Rows per page:
20 50 100 500
Go to page:
of 1 pages -
has anyone seen this on their dot1x configurations where the vlan info is missing on the show running-config? see port fast 2/0/3 below. the 3750 POE switch is running 12.2.55-SE7.
interface FastEthernet2/0/1
switchport access vlan 18
switchport mode access
switchport nonegotiate
switchport voice vlan 101
srr-queue bandwidth share 10 10 60 20
srr-queue bandwidth shape 10 0 0 0
priority-queue out
authentication event fail action authorize vlan 34
authentication event server dead action authorize
authentication event server dead action authorize voice
authentication event no-response action authorize vlan 34
authentication host-mode multi-domain
authentication order dot1x mab
authentication port-control auto
authentication violation restrict
mab
mls qos trust dscp
auto qos voip trust
dot1x pae authenticator
dot1x timeout quiet-period 3
dot1x timeout tx-period 3
dot1x timeout supp-timeout 3
storm-control broadcast level 1.00
spanning-tree portfast
spanning-tree bpduguard enable
interface FastEthernet2/0/2
switchport access vlan 18
switchport mode access
switchport nonegotiate
switchport voice vlan 101
srr-queue bandwidth share 10 10 60 20
srr-queue bandwidth shape 10 0 0 0
priority-queue out
authentication event fail action authorize vlan 34
authentication event server dead action authorize
authentication event server dead action authorize voice
authentication event no-response action authorize vlan 34
authentication host-mode multi-domain
authentication order dot1x mab
authentication port-control auto
authentication violation restrict
mab
mls qos trust dscp
auto qos voip trust
dot1x pae authenticator
dot1x timeout quiet-period 3
dot1x timeout tx-period 3
dot1x timeout supp-timeout 3
storm-control broadcast level 1.00
spanning-tree portfast
spanning-tree bpduguard enable
interface FastEthernet2/0/3
switchport access vlan 18
switchport mode access
switchport nonegotiate
switchport voice vlan 101
srr-queue bandwidth share 10 10 60 20
srr-queue bandwidth shape 10 0 0 0
priority-queue out
authentication event fail action authorize
authentication event server dead action authorize
authentication event server dead action authorize voice
authentication event no-response action authorize vlan 34
authentication host-mode multi-domain
authentication order dot1x mab
authentication port-control auto
authentication violation restrict
mab
mls qos trust dscp
auto qos voip trust
dot1x pae authenticator
dot1x timeout quiet-period 3
dot1x timeout tx-period 3
dot1x timeout supp-timeout 3
storm-control broadcast level 1.00
spanning-tree portfast
spanning-tree bpduguard enable
interface FastEthernet2/0/4
switchport access vlan 18
switchport mode access
switchport nonegotiate
switchport voice vlan 101
srr-queue bandwidth share 10 10 60 20
srr-queue bandwidth shape 10 0 0 0
priority-queue out
authentication event fail action authorize
authentication event server dead action authorize
authentication event server dead action authorize voice
authentication event no-response action authorize vlan 34
authentication host-mode multi-domain
authentication order dot1x mab
authentication port-control auto
authentication violation restrict
mab
mls qos trust dscp
auto qos voip trust
dot1x pae authenticator
dot1x timeout quiet-period 3
dot1x timeout tx-period 3
dot1x timeout supp-timeout 3
storm-control broadcast level 1.00
spanning-tree portfast
spanning-tree bpduguard enable
interface FastEthernet2/0/5
switchport access vlan 18
switchport mode access
switchport nonegotiate
switchport voice vlan 101
srr-queue bandwidth share 10 10 60 20
srr-queue bandwidth shape 10 0 0 0
priority-queue out
authentication event fail action authorize
authentication event server dead action authorize
authentication event server dead action authorize voice
authentication event no-response action authorize vlan 34
authentication host-mode multi-domain
authentication order dot1x mab
authentication port-control auto
authentication violation restrict
mab
mls qos trust dscp
auto qos voip trust
dot1x pae authenticator
dot1x timeout quiet-period 3
dot1x timeout tx-period 3
dot1x timeout supp-timeout 3
storm-control broadcast level 1.00
spanning-tree portfast
spanning-tree bpduguard enable
interface FastEthernet2/0/6
switchport access vlan 18
switchport mode access
switchport nonegotiate
switchport voice vlan 101
srr-queue bandwidth share 10 10 60 20
srr-queue bandwidth shape 10 0 0 0
priority-queue out
authentication event fail action authorize vlan 34
authentication event server dead action authorize
authentication event server dead action authorize voice
authentication event no-response action authorize vlan 34
authentication host-mode multi-domain
authentication order dot1x mab
authentication port-control auto
authentication violation restrict
mab
mls qos trust dscp
auto qos voip trust
dot1x pae authenticator
dot1x timeout quiet-period 3
dot1x timeout tx-period 3
dot1x timeout supp-timeout 3
storm-control broadcast level 1.00
spanning-tree portfast
spanning-tree bpduguard enableThe vlan info isn't missing, you have the option of either specifying which VLAN you want it dropped in to, or you can just say authorize the vlan that is configured with the 'switchport access vlan' command.
-
Get running config to ftp server failed
i has already set every one read and write in folder named tin in desktop in window 7, but still can not create file and write file after using ftp
static ip of network card i set 192.168.1.207 in window 7 connected to one of switchport mode access port in switch
first i use filezilla
as01#copy running-config ftp:
Address or name of remote host []? 192.168.1.207
Destination filename [as01-confg]?
Writing as01-confg
%Error writing ftp://192.168.1.207/as01-confg (Undefined error)
then i use tftpd32 , set binding address 192.168.1.207
as01#copy running-config ftp:
Address or name of remote host []? 192.168.1.207
Destination filename [as01-confg]?
Writing as01-confg
%Error writing ftp://192.168.1.207/as01-confg (Undefined error)
then i change to use IIS 's ftp, it can upload file by drag and drop , but right click do not have create file
when i see cisco is writing, i do not know whether it is uploading or creating file and write to itthe switch can ping
as01#ping 192.168.1.207
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.207, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
i have tried tftp
as01#copy system:running-config tftp:
Address or name of remote host []? 192.168.1.207
Destination filename [as01-confg]?
%Error opening tftp://192.168.1.207/as01-confg (Timed out)
tried no passive still failed
noc01as01#sh run | be FastEthernet0/21
ip tftp source-interface FastEthernet0/21
conf t
int FastEthernet0/21
switchport mode access
end
sh run | be FastEthernet0/21
copy running-config tftp:
conf t
no ip ftp passive
ip ftp user noc
ip ftp password 123
end
finally i use wireshark to see, there is no ftp protocol connection with my notebook
then off Macfee IPS, firewall,
and filter with ftp in wireshark , there is no ftp show in wireshark -
N5K - commit imported config always failed
Hello al.
I have upgrade a N5K (5010) cluster to SW version 5.0(2)N1(1)
When I want to commit a configuration into a switch profile I always receive the error "Failed: Verify Failed"
Neither I want to commit only one rule I still receive the same error.
Any Idea what I'm doing wrong?
I followed the Release Notes for 5.0(2
http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/release/notes/Rel_5_0_2_N1_1/Nexus5000_Release_Notes_5_0_2_N1_1.html
HI16955# configure sync
Enter configuration commands, one per line. End with CNTL/Z.
HI16955(config-sync)# switch-profile SYNC
Switch-Profile started, Profile ID is 1
HI16955(config-sync-sp)# import running-config
HI16955(config-sync-sp-import)# show switch-profile SYNC buffer
switch-profile : SYNC
Seq-no Command
4 vlan 3
4.1 name 3_vlan_3
5 vlan 4
5.1 name 4_mgmt_mon
6 vlan 5
6.1 name 5_tp_router
7 vlan 6
7.1 name 6_int_servers
8 vlan 8
8.1 name 8_vpn_lan
9 vlan 10
9.1 name 10_dmz1
HI16955(config-sync-sp-import)# commit
Failed: Verify Failed
HI16955(config-sync-sp-import)#
Regards
Tom LauwereinsHello al.
I have upgrade a N5K (5010) cluster to SW version 5.0(2)N1(1)
When I want to commit a configuration into a switch profile I always receive the error "Failed: Verify Failed"
Neither I want to commit only one rule I still receive the same error.
Any Idea what I'm doing wrong?
I followed the Release Notes for 5.0(2
http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/release/notes/Rel_5_0_2_N1_1/Nexus5000_Release_Notes_5_0_2_N1_1.html
HI16955# configure sync
Enter configuration commands, one per line. End with CNTL/Z.
HI16955(config-sync)# switch-profile SYNC
Switch-Profile started, Profile ID is 1
HI16955(config-sync-sp)# import running-config
HI16955(config-sync-sp-import)# show switch-profile SYNC buffer
switch-profile : SYNC
Seq-no Command
4 vlan 3
4.1 name 3_vlan_3
5 vlan 4
5.1 name 4_mgmt_mon
6 vlan 5
6.1 name 5_tp_router
7 vlan 6
7.1 name 6_int_servers
8 vlan 8
8.1 name 8_vpn_lan
9 vlan 10
9.1 name 10_dmz1
HI16955(config-sync-sp-import)# commit
Failed: Verify Failed
HI16955(config-sync-sp-import)#
Regards
Tom Lauwereins -
Boot system flash: does not appear on 2960 running config
Dear friends,
On the 2960, i have two .bin images and i am pointing to the latest one.
However, the boot system flash: command along with the new image does not appear in the running config but it appears in the
show boot command.
t3a.sidradc.dmz.01#dir flash:
Directory of flash:/
2 -rwx 2131 Jan 3 2010 07:30:45 +03:00 private-config.text
4 -rwx 8040418 Mar 1 1993 05:31:51 +03:00 c2960-lanbasek9-mz.122-50.SE3.bin
5 -rwx 676 Jan 3 2010 07:28:50 +03:00 vlan.dat
6 drwx 128 Mar 1 1993 03:02:32 +03:00 c2960-lanbasek9-mz.122-44.SE6
546 -rwx 4120 Jan 3 2010 07:30:45 +03:00 multiple-fs
548 -rwx 9001 Jan 3 2010 07:30:45 +03:00 config.text
32514048 bytes total (21123072 bytes free)
t3a.sidradc.dmz.01(config)#boot system flash:c2960-lanbasek9-mz.122-50.SE3.bin
t3a.sidradc.dmz.01(config)#exit
t3a.sidradc.dmz.01#wr
Building configuration...
[OK]
t3a.sidradc.dmz.01#sh boot
BOOT path-list : flash:c2960-lanbasek9-mz.122-50.SE3.bin
Config file : flash:/config.text
Private Config file : flash:/private-config.text
Enable Break : no
Manual Boot : no
HELPER path-list :
Auto upgrade : yes
Auto upgrade path :
NVRAM/Config file
buffer size: 65536
Timeout for Config
Download: 0 seconds
Config Download
via DHCP: disabled (next boot: disabled)
t3a.sidradc.dmz.01#sh run | inc boot
boot-start-marker
boot-end-marker
Are you aware of any reasons for this?
Thanks a lot
Gautamand the other being the issue where IOS can return the prompt before it's done unpacking the files
Ok, now what EXACTLY is the appliance and IOS version? The only time I know of this bug is the Metro Ethernet (ME) switches and when the current appliance is upgraded FROM an IOS version 15.2(1)S.
But there is a "workaround" which Cisco doesn't want to publish (don't ask me why not): Use "archive tar /x" and, optionally, delete the old IOS sub-directory.
Personally, I wouldn't recommend anyone using the "copy the BIN file" method unless you know what you are doing or you've put extra measures in place. The "archive /x tar" and/or "archive download-sw" was developed so that it could be automated and the operator can see the result at the end. The "copy the BIN file" method doesn't give anyone a result whether or not the file was copied or not or was the file copied completely.
Regularly, I would upgrade our switches (2960/2960S, ME-3800X, 3560E/3560CG, 3750X) fleet using the "archive download-sw" method and I don't use scripts. I just copy-and-paste the command. So far, since 2009, I've "lost" only 6 switches when I upgraded the switch to upgrade the wrong file (another IOS bug on it's own) and I had to physically show up and upgrade using ROMmon. Every time I would upgrade, about 900 switches (some in a stack), it would take me about 4 days. Even though I work with three guys who's very good at almost any scripting but we've come to a unanimous conclusion NOT to use scripting.
Moving on, if "copy the BIN file" is still a preferred choice, I would like to know how do you go about verifying the file was copied completely? Whenever I resort to the "copy the BIN file", I ensure the file copied is complete by verifying the MD5 hash value against the MD5 hash value found in the Cisco website. Trust me, adding this additional "layer" of security saved me doing ROMmon upgrade so many times. -
[nQSError: 17012] Bulk fetch failed. (HY000)
Hi All,
Some times my report through's the following error message:
ORA-03135: Attached the query which results into an error after running for 31 minutes. Below is the error:
State: HY000. Code: 10058. [NQODBC] [SQL_STATE: HY000] [nQSError: 10058] A general error has occurred. [nQSError: 43113] Message returned from OBIS. [nQSError: 43119] Query Failed: [nQSError: 17001] Oracle Error code: 3135, message: ORA-03135: connection lost contact Process ID: 25523 Session ID: 774 Serial number: 19622 at OCI call OCIStmtFetch. [nQSError: 17012] Bulk fetch failed. (HY000)
Please give me the solution.
Thanks&Regards,
Nantha.I see the irony was lost as your reply remained unprecise and un-informative. "Server side everything ok" - what does that even mean? BI server? Database server? What about the network? What about firewall issues with the expire_time parameter in the sqlnet.ora? Are you working with virtual machines on either side (or both)?
http://catb.org/~esr/faqs/smart-questions.html -
Getting "File copy Config Sync Failed. Commit unsuccessful! " on CSS-11155
Getting a strange error "FILE copy Config Sync Failed. Commit unsuccessful!" from the following and I am not sure what it exactly means:
cce01-c35-in# sh app
APP CONFIGURATION:
Enabled PortNumber: 5001 MaxFrameSize: 10240
cce01-c35-in# sh app session
App Session Information 'no hostname':
Session ID: 839f0990 IP Address: 10.10.10.2 State: APP_SESSION_UP
css-c09-nz# commit_redundConfig "10.10.10.2"
Verifying app and redundancy configs ... -
Checking local and remote switch versions ...|
Checking Backup app session up.... \
Checking redundancy state.... -
Working /
Waiting for completion signal from remote switch .../
Verifying running-config copy success ...-
File copy Config Sync Failed. Commit unsuccessful!
localconfig: 6238 bytes
remoteconfig : 6150 bytes
css-c09-nz#there is at least one know bug :
CSCdx89818 - config sync fails
I could not check if this applies to you since you did not provide your version.
This bug was fixed in the following release :
006.010(000.004) 05.3(00.18)S 05.0(00.54)S 05.10(01.03)S
Gilles. -
Cisco LMS netconfig job not saving running config to startup
Hi,
I'm running LMS3.2 and RME 4.3.1. I deployed a netconfig job to our network which consisted of approximately 800 devices.
The report said that the job completed successfully however some of the devices didn't save thier running config to startup. Has anyone experienced this before?
Is it possible to add a command or issue another netconfig job just to save the running config, so I can identify if the job fails on some devices? Using the tick box in the netconfig job doesn't seem to alert you if its not successful.
Thanks,I have seen in the past where someone is running a netconfig job with the cmd to "wr mem" as a line in the netconfig job.
Sven is correct, there is an option; radio button/check box to save the running config to startup after the job is completed.
if your job is strictly meant to "wr mem/write the config" then run a show command in config mode (non-enable) mode and select the option to save running config after job is completed. -
Cisco WLC 5500 ver.8 running config
Does anybody have a complete "show-run" running config from a 5500 series controller, "sanitized" of course, they would care to post to share?
I need to create some config examples and do not have a piece of hardware to work with.
Thanks=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2015.01.13 14:15:58 =~=~=~=~=~=~=~=~=~=~=~=
config paging disable
Press Enter to continue...
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.130.2
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... Viten_2504
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 192.168.162.20
Last Reset....................................... Software reset
System Up Time................................... 1 days 2 hrs 23 mins 10 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... US - United States
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +27 C
External Temperature............................. +30 C
Fan Status....................................... 4100 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 2
Number of Active Clients......................... 0
Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown
Burned-in MAC Address............................ 50:06:04:CB:76:C0
Maximum number of APs supported.................. 25
AP Bundle Information
Primary AP Image Size
ap1g2 9588
ap3g1 11308
ap3g2 11216
ap801 7172
ap802 8588
c1130 5072
c1140 9428
c1250 6964
c1520 8072
c602i 3744
Secondary AP Image Size
ap1g2 9576
ap3g1 11296
ap3g2 11208
ap801 7164
ap802 8576
c1130 5072
c1140 9428
c1250 6964
c1520 8064
c602i 3736
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Strong Password Check Features:
case-check ...........Enabled
consecutive-check ....Enabled
default-check .......Enabled
username-check ......Enabled
Network Information
RF-Network Name............................. wnbu
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Disable
Secure Web Mode RC4 Cipher Preference....... Disable
Secure Web Mode SSL Protocol................ Disable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Multicast Address : 0.0.0.0
IGMP snooping............................... Enabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
MLD snooping................................ Disabled
MLD timeout................................. 60 seconds
MLD query interval.......................... 20 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Disable
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
AP Fallback ................................ Enable
Web Auth CMCC Support ...................... Disabled
Web Auth Redirect Ports .................... 80
Web Auth Proxy Redirect ................... Disable
Web Auth Captive-Bypass .................. Disable
Web Auth Secure Web ....................... Enable
Fast SSID Change ........................... Enabled
AP Discovery - NAT IP Only ................. Enabled
IP/MAC Addr Binding Check .................. Enabled
CCX-lite status ............................ Disable
oeap-600 dual-rlan-ports ................... Disable
oeap-600 local-network ..................... Enable
mDNS snooping............................... Disabled
mDNS Query Interval......................... 15 minutes
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE
1 Normal Forw Enable Auto 1000 Full Up Enable N/A
2 Normal Disa Enable Auto Auto Down Enable N/A
3 Normal Disa Enable Auto Auto Down Enable N/A
4 Normal Disa Enable Auto Auto Down Enable N/A
AP Summary
Number of APs.................................... 3
Global AP User Name.............................. admin
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Viten_1142_2 2 AIR-LAP1142N-A-K9 00:22:bd:19:d5:80 default location LAG US 1
Viten_1142_1 2 AIR-LAP1142N-A-K9 00:22:90:90:df:6c default location LAG US 1
Viten_2602_2 2 AIR-CAP2602I-A-K9 c0:67:af:58:e0:db default location LAG US 1
AP Tcp-Mss-Adjust Info
AP Name TCP State MSS Size
Viten_1142_2 disabled -
Viten_1142_1 disabled -
Viten_2602_2 disabled -
AP Location
Total Number of AP Groups........................ 0
Site Name........................................ default-group
Site Description................................. <none>
NAS-identifier................................... Viten_2504
AP Operating Class............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
1 management Disabled None
4 management Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Viten_1142_2 2 AIR-LAP1142N-A-K9 00:22:bd:19:d5:80 default location LAG US 1
Viten_1142_1 2 AIR-LAP1142N-A-K9 00:22:90:90:df:6c default location LAG US 1
Viten_2602_2 2 AIR-CAP2602I-A-K9 c0:67:af:58:e0:db default location LAG US 1
RF Profile
Number of RF Profiles............................ 7
Out Of Box State................................. Disabled
RF Profile Name Band Description 11n-client-only
High-Client-Density-(802.11a) 5 GHz <none> disable No
High-Client-Density-(802.11bg) 2.4 GHz <none> disable No
Low-Client-Density-(802.11a) 5 GHz <none> disable No
Low-Client-Density-(802.11bg) 2.4 GHz <none> disable No
Typical-Client-Density(802.11bg) 2.4 GHz <none> disable No
Typical-Client-Density-(802.11a) 5 GHz <none> disable No
test 5 GHz <none> disable No
RF Profile name................................ High-Client-Density-(802.11a)
Description...................................... <none>
11n-client-only.................................. disabled
Radio policy..................................... 5 GHz
Transmit Power Threshold v1...................... -65 dBm
Transmit Power Threshold v2...................... -67 dBm
Min Transmit Power............................... 7 dBm
Max Transmit Power............................... 30 dBm
802.11a Operational Rates
802.11a 6M Rate.............................. Mandatory
802.11a 9M Rate.............................. Supported
802.11a 12M Rate............................. Mandatory
802.11a 18M Rate............................. Supported
802.11a 24M Rate............................. Mandatory
802.11a 36M Rate............................. Supported
802.11a 48M Rate............................. Supported
802.11a 54M Rate............................. Supported
Max Clients...................................... 200
WLAN ID maxClients
Client Trap Threshold............................ 50
Multicast Data Rate.............................. 0
Rx Sop Threshold................................. -78 dBm
Cca Threshold.................................... 0 dBm
Slot Admin State:................................ Enabled
Band Select Probe Response....................... Disabled
Band Select Cycle Count.......................... 2 cycles
Band Select Cycle Threshold...................... 200 milliseconds
Band Select Expire Suppression................... 20 seconds
Band Select Expire Dual Band..................... 60 seconds
Band Select Client Rssi.......................... -80 dBm
Load Balancing Denial............................ 3 count
Load Balancing Window............................ 5 clients
Coverage Data.................................... -80 dBm
Coverage Voice................................... -80 dBm
Coverage Exception............................... 3 clients
Coverage Level................................... 25 %
802.11n MCS Rates
MCS-00 Rate.................................. enabled
MCS-01 Rate.................................. enabled
MCS-02 Rate.................................. enabled
MCS-03 Rate.................................. enabled
MCS-04 Rate.................................. enabled
MCS-05 Rate.................................. enabled
MCS-06 Rate.................................. enabled
MCS-07 Rate.................................. enabled
MCS-08 Rate.................................. enabled
MCS-09 Rate.................................. enabled
MCS-10 Rate.................................. enabled
MCS-11 Rate.................................. enabled
MCS-12 Rate.................................. enabled
MCS-13 Rate.................................. enabled
MCS-14 Rate.................................. enabled
MCS-15 Rate.................................. enabled
MCS-16 Rate.................................. enabled
MCS-17 Rate.................................. enabled
MCS-18 Rate.................................. enabled
MCS-19 Rate.................................. enabled
MCS-20 Rate.................................. enabled
MCS-21 Rate.................................. enabled
MCS-22 Rate.................................. enabled
MCS-23 Rate.................................. enabled
RF Profile name................................ High-Client-Density-(802.11bg)
Description...................................... <none>
11n-client-only.................................. disabled
Radio policy..................................... 2.4 GHz
Transmit Power Threshold v1...................... -70 dBm
Transmit Power Threshold v2...................... -67 dBm
Min Transmit Power............................... 7 dBm
Max Transmit Power............................... 30 dBm
802.11b/g Operational Rates
802.11b/g 1M Rate............................ Disabled
802.11b/g 2M Rate............................ Disabled
802.11b/g 5.5M Rate.......................... Disabled
802.11b/g 11M Rate........................... Disabled
802.11g 6M Rate.............................. Disabled
802.11g 9M Rate.............................. Supported
802.11g 12M Rate............................. Mandatory
802.11g 18M Rate............................. Supported
802.11g 24M Rate............................. Supported
802.11g 36M Rate............................. Supported
802.11g 48M Rate............................. Supported
802.11g 54M Rate............................. Supported
Max Clients...................................... 200
WLAN ID maxClients
Client Trap Threshold............................ 50
Multicast Data Rate.............................. 0
Rx Sop Threshold................................. -82 dBm
Cca Threshold.................................... 0 dBm
Slot Admin State:................................ Enabled
Band Select Probe Response....................... Disabled
Band Select Cycle Count.......................... 2 cycles
Band Select Cycle Threshold...................... 200 milliseconds
Band Select Expire Suppression................... 20 seconds
Band Select Expire Dual Band..................... 60 seconds
Band Select Client Rssi.......................... -80 dBm
Load Balancing Denial............................ 3 count
Load Balancing Window............................ 5 clients
Coverage Data.................................... -80 dBm
Coverage Voice................................... -80 dBm
Coverage Exception............................... 3 clients
Coverage Level................................... 25 %
802.11n MCS Rates
MCS-00 Rate.................................. enabled
MCS-01 Rate.................................. enabled
MCS-02 Rate.................................. enabled
MCS-03 Rate.................................. enabled
MCS-04 Rate.................................. enabled
MCS-05 Rate.................................. enabled
MCS-06 Rate.................................. enabled
MCS-07 Rate.................................. enabled
MCS-08 Rate.................................. enabled
MCS-09 Rate.................................. enabled
MCS-10 Rate.................................. enabled
MCS-11 Rate.................................. enabled
MCS-12 Rate.................................. enabled
MCS-13 Rate.................................. enabled
MCS-14 Rate.................................. enabled
MCS-15 Rate.................................. enabled
MCS-16 Rate.................................. enabled
MCS-17 Rate.................................. enabled
MCS-18 Rate.................................. enabled
MCS-19 Rate.................................. enabled
MCS-20 Rate.................................. enabled
MCS-21 Rate.................................. enabled
MCS-22 Rate.................................. enabled
MCS-23 Rate.................................. enabled
RF Profile name................................ Low-Client-Density-(802.11a)
Description...................................... <none>
11n-client-only.................................. disabled
Radio policy..................................... 5 GHz
Transmit Power Threshold v1...................... -60 dBm
Transmit Power Threshold v2...................... -67 dBm
Min Transmit Power............................... -10 dBm
Max Transmit Power............................... 30 dBm
802.11a Operational Rates
802.11a 6M Rate.............................. Mandatory
802.11a 9M Rate.............................. Supported
802.11a 12M Rate............................. Mandatory
802.11a 18M Rate............................. Supported
802.11a 24M Rate............................. Mandatory
802.11a 36M Rate............................. Supported
802.11a 48M Rate............................. Supported
802.11a 54M Rate............................. Supported
Max Clients...................................... 200
WLAN ID maxClients
Client Trap Threshold............................ 50
Multicast Data Rate.............................. 0
Rx Sop Threshold................................. -80 dBm
Cca Threshold.................................... 0 dBm
Slot Admin State:................................ Enabled
Band Select Probe Response....................... Disabled
Band Select Cycle Count.......................... 2 cycles
Band Select Cycle Threshold...................... 200 milliseconds
Band Select Expire Suppression................... 20 seconds
Band Select Expire Dual Band..................... 60 seconds
Band Select Client Rssi.......................... -80 dBm
Load Balancing Denial............................ 3 count
Load Balancing Window............................ 5 clients
Coverage Data.................................... -90 dBm
Coverage Voice................................... -90 dBm
Coverage Exception............................... 3 clients
Coverage Level................................... 25 %
802.11n MCS Rates
MCS-00 Rate.................................. enabled
MCS-01 Rate.................................. enabled
MCS-02 Rate.................................. enabled
MCS-03 Rate.................................. enabled
MCS-04 Rate.................................. enabled
MCS-05 Rate.................................. enabled
MCS-06 Rate.................................. enabled
MCS-07 Rate.................................. enabled
MCS-08 Rate.................................. enabled
MCS-09 Rate.................................. enabled
MCS-10 Rate.................................. enabled
MCS-11 Rate.................................. enabled
MCS-12 Rate.................................. enabled
MCS-13 Rate.................................. enabled
MCS-14 Rate.................................. enabled
MCS-15 Rate.................................. enabled
MCS-16 Rate.................................. enabled
MCS-17 Rate.................................. enabled
MCS-18 Rate.................................. enabled
MCS-19 Rate.................................. enabled
MCS-20 Rate.................................. enabled
MCS-21 Rate.................................. enabled
MCS-22 Rate.................................. enabled
MCS-23 Rate.................................. enabled
RF Profile name................................ Low-Client-Density-(802.11bg)
Description...................................... <none>
11n-client-only.................................. disabled
Radio policy..................................... 2.4 GHz
Transmit Power Threshold v1...................... -65 dBm
Transmit Power Threshold v2...................... -67 dBm
Min Transmit Power............................... -10 dBm
Max Transmit Power............................... 30 dBm
802.11b/g Operational Rates
802.11b/g 1M Rate............................ Mandatory
802.11b/g 2M Rate............................ Mandatory
802.11b/g 5.5M Rate.......................... Mandatory
802.11b/g 11M Rate........................... Mandatory
802.11g 6M Rate.............................. Supported
802.11g 9M Rate.............................. Supported
802.11g 12M Rate............................. Supported
802.11g 18M Rate............................. Supported
802.11g 24M Rate............................. Supported
802.11g 36M Rate............................. Supported
802.11g 48M Rate............................. Supported
802.11g 54M Rate............................. Supported
Max Clients...................................... 200
WLAN ID maxClients
Client Trap Threshold............................ 50
Multicast Data Rate.............................. 0
Rx Sop Threshold................................. -85 dBm
Cca Threshold.................................... 0 dBm
Slot Admin State:................................ Enabled
Band Select Probe Response....................... Disabled
Band Select Cycle Count.......................... 2 cycles
Band Select Cycle Threshold...................... 200 milliseconds
Band Select Expire Suppression................... 20 seconds
Band Select Expire Dual Band..................... 60 seconds
Band Select Client Rssi.......................... -80 dBm
Load Balancing Denial............................ 3 count
Load Balancing Window............................ 5 clients
Coverage Data.................................... -90 dBm
Coverage Voice................................... -90 dBm
Coverage Exception............................... 3 clients
Coverage Level................................... 25 %
802.11n MCS Rates
MCS-00 Rate.................................. enabled
MCS-01 Rate.................................. enabled
MCS-02 Rate.................................. enabled
MCS-03 Rate.................................. enabled
MCS-04 Rate.................................. enabled
MCS-05 Rate.................................. enabled
MCS-06 Rate.................................. enabled
MCS-07 Rate.................................. enabled
MCS-08 Rate.................................. enabled
MCS-09 Rate.................................. enabled
MCS-10 Rate.................................. enabled
MCS-11 Rate.................................. enabled
MCS-12 Rate.................................. enabled
MCS-13 Rate.................................. enabled
MCS-14 Rate.................................. enabled
MCS-15 Rate.................................. enabled
MCS-16 Rate.................................. enabled
MCS-17 Rate.................................. enabled
MCS-18 Rate.................................. enabled
MCS-19 Rate.................................. enabled
MCS-20 Rate.................................. enabled
MCS-21 Rate.................................. enabled
MCS-22 Rate.................................. enabled
MCS-23 Rate.................................. enabled
RF Profile name................................ Typical-Client-Density(802.11bg)
Description...................................... <none>
11n-client-only.................................. disabled
Radio policy..................................... 2.4 GHz
Transmit Power Threshold v1...................... -70 dBm
Transmit Power Threshold v2...................... -67 dBm
Min Transmit Power............................... -10 dBm
Max Transmit Power............................... 30 dBm
802.11b/g Operational Rates
802.11b/g 1M Rate............................ Disabled
802.11b/g 2M Rate............................ Disabled
802.11b/g 5.5M Rate.......................... Disabled
802.11b/g 11M Rate........................... Disabled
802.11g 6M Rate.............................. Disabled
802.11g 9M Rate.............................. Supported
802.11g 12M Rate............................. Mandatory
802.11g 18M Rate............................. Supported
802.11g 24M Rate............................. Supported
802.11g 36M Rate............................. Supported
802.11g 48M Rate............................. Supported
802.11g 54M Rate............................. Supported
Max Clients...................................... 200
WLAN ID maxClients
Client Trap Threshold............................ 50
Multicast Data Rate.............................. 0
Rx Sop Threshold................................. 0 dBm
Cca Threshold.................................... 0 dBm
Slot Admin State:................................ Enabled
Band Select Probe Response....................... Disabled
Band Select Cycle Count.......................... 2 cycles
Band Select Cycle Threshold...................... 200 milliseconds
Band Select Expire Suppression................... 20 seconds
Band Select Expire Dual Band..................... 60 seconds
Band Select Client Rssi.......................... -80 dBm
Load Balancing Denial............................ 3 count
Load Balancing Window............................ 5 clients
Coverage Data.................................... -80 dBm
Coverage Voice................................... -80 dBm
Coverage Exception............................... 3 clients
Coverage Level................................... 25 %
802.11n MCS Rates
MCS-00 Rate.................................. enabled
MCS-01 Rate.................................. enabled
MCS-02 Rate.................................. enabled
MCS-03 Rate.................................. enabled
MCS-04 Rate.................................. enabled
MCS-05 Rate.................................. enabled
MCS-06 Rate.................................. enabled
MCS-07 Rate.................................. enabled
MCS-08 Rate.................................. enabled
MCS-09 Rate.................................. enabled
MCS-10 Rate.................................. enabled
MCS-11 Rate.................................. enabled
MCS-12 Rate.................................. enabled
MCS-13 Rate.................................. enabled
MCS-14 Rate.................................. enabled
MCS-15 Rate.................................. enabled
MCS-16 Rate.................................. enabled
MCS-17 Rate.................................. enabled
MCS-18 Rate.................................. enabled
MCS-19 Rate.................................. enabled
MCS-20 Rate.................................. enabled
MCS-21 Rate.................................. enabled
MCS-22 Rate.................................. enabled
MCS-23 Rate.................................. enabled
RF Profile name................................ Typical-Client-Density-(802.11a)
Description...................................... <none>
11n-client-only.................................. disabled
Radio policy..................................... 5 GHz
Transmit Power Threshold v1...................... -70 dBm
Transmit Power Threshold v2...................... -67 dBm
Min Transmit Power............................... -10 dBm
Max Transmit Power............................... 30 dBm
802.11a Operational Rates
802.11a 6M Rate.............................. Mandatory
802.11a 9M Rate.............................. Supported
802.11a 12M Rate............................. Mandatory
802.11a 18M Rate............................. Supported
802.11a 24M Rate............................. Mandatory
802.11a 36M Rate............................. Supported
802.11a 48M Rate............................. Supported
802.11a 54M Rate............................. Supported
Max Clients...................................... 200
WLAN ID maxClients
Client Trap Threshold............................ 50
Multicast Data Rate.............................. 0
Rx Sop Threshold................................. 0 dBm
Cca Threshold.................................... 0 dBm
Slot Admin State:................................ Enabled
Band Select Probe Response....................... Disabled
Band Select Cycle Count.......................... 2 cycles
Band Select Cycle Threshold...................... 200 milliseconds
Band Select Expire Suppression................... 20 seconds
Band Select Expire Dual Band..................... 60 seconds
Band Select Client Rssi.......................... -80 dBm
Load Balancing Denial............................ 3 count
Load Balancing Window............................ 5 clients
Coverage Data.................................... -80 dBm
Coverage Voice................................... -80 dBm
Coverage Exception............................... 3 clients
Coverage Level................................... 25 %
802.11n MCS Rates
MCS-00 Rate.................................. enabled
MCS-01 Rate.................................. enabled
MCS-02 Rate.................................. enabled
MCS-03 Rate.................................. enabled
MCS-04 Rate.................................. enabled
MCS-05 Rate.................................. enabled
MCS-06 Rate.................................. enabled
MCS-07 Rate.................................. enabled
MCS-08 Rate.................................. enabled
MCS-09 Rate.................................. enabled
MCS-10 Rate.................................. enabled
MCS-11 Rate.................................. enabled
MCS-12 Rate.................................. enabled
MCS-13 Rate.................................. enabled
MCS-14 Rate.................................. enabled
MCS-15 Rate.................................. enabled
MCS-16 Rate.................................. enabled
MCS-17 Rate.................................. enabled
MCS-18 Rate.................................. enabled
MCS-19 Rate.................................. enabled
MCS-20 Rate.................................. enabled
MCS-21 Rate.................................. enabled
MCS-22 Rate.................................. enabled
MCS-23 Rate.................................. enabled
RF Profile name................................ test
Description...................................... <none>
11n-client-only.................................. disabled
Radio policy..................................... 5 GHz
Transmit Power Threshold v1...................... -70 dBm
Transmit Power Threshold v2...................... -67 dBm
Min Transmit Power............................... -10 dBm
Max Transmit Power............................... 30 dBm
802.11a Operational Rates
802.11a 6M Rate.............................. Mandatory
802.11a 9M Rate.............................. Supported
802.11a 12M Rate............................. Mandatory
802.11a 18M Rate............................. Supported
802.11a 24M Rate............................. Mandatory
802.11a 36M Rate............................. Supported
802.11a 48M Rate............................. Supported
802.11a 54M Rate............................. Supported
Max Clients...................................... 200
WLAN ID maxClients
Client Trap Threshold............................ 50
Multicast Data Rate.............................. 0
Rx Sop Threshold................................. 0 dBm
Cca Threshold.................................... 0 dBm
Slot Admin State:................................ Enabled
Band Select Probe Response....................... Disabled
Band Select Cycle Count.......................... 2 cycles
Band Select Cycle Threshold...................... 200 milliseconds
Band Select Expire Suppression................... 20 seconds
Band Select Expire Dual Band..................... 60 seconds
Band Select Client Rssi.......................... -80 dBm
Load Balancing Denial............................ 3 count
Load Balancing Window............................ 5 clients
Coverage Data.................................... -80 dBm
Coverage Voice................................... -80 dBm
Coverage Exception............................... 3 clients
Coverage Level................................... 25 %
802.11n MCS Rates
MCS-00 Rate.................................. enabled
MCS-01 Rate.................................. enabled
MCS-02 Rate.................................. enabled
MCS-03 Rate.................................. enabled
MCS-04 Rate.................................. enabled
MCS-05 Rate.................................. enabled
MCS-06 Rate.................................. enabled
MCS-07 Rate.................................. enabled
MCS-08 Rate.................................. enabled
MCS-09 Rate.................................. enabled
MCS-10 Rate.................................. enabled
MCS-11 Rate.................................. enabled
MCS-12 Rate.................................. enabled
MCS-13 Rate.................................. enabled
MCS-14 Rate.................................. enabled
MCS-15 Rate.................................. enabled
MCS-16 Rate.................................. enabled
MCS-17 Rate.................................. enabled
MCS-18 Rate.................................. enabled
MCS-19 Rate.................................. enabled
MCS-20 Rate.................................. enabled
MCS-21 Rate.................................. enabled
MCS-22 Rate.................................. enabled
MCS-23 Rate.................................. enabled
AP Config
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... Viten_1142_2
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 13
MAC Address...................................... 00:22:bd:19:d5:80
IP Address Configuration......................... DHCP
IP Address....................................... 192.168.162.110
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 192.168.162.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Enabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Floor Label............................. 0
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................ Viten_2504
Primary Cisco Switch IP Address.................. 192.168.162.20
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... FlexConnect
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... system
S/W Version .................................... 7.4.130.2
Boot Version ................................... 12.4.18.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
Stats Collection Mode ........................... normal
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1142N-A-K9
AP Image......................................... C1140-K9W8-M
IOS Version...................................... 15.2(20150109:075323)$
Reset Button..................................... Enabled
AP Serial Number................................. FTX1332SBYY
AP Certificate Type.............................. Manufacture Installed
FlexConnect Vlan mode :.......................... Disabled
FlexConnect Group................................ Not a member of any group
Group VLAN ACL Mappings
FlexConnect Local-Split ACLs :
WLAN ID PROFILE NAME ACL TYPE
Flexconnect Central-Dhcp Values :
WLAN ID PROFILE NAME Central-Dhcp DNS Override Nat-Pat Type
4 test123 False False False Wlan
FlexConnect Backup Auth Radius Servers :
Primary Radius Server........................... Disabled
Secondary Radius Server......................... Disabled
AP User Mode..................................... CUSTOMIZED
AP User Name..................................... admin
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 10.6.0.25
AP Up Time....................................... 1 days, 02 h 13 m 41 s
AP LWAPP Up Time................................. 1 days, 02 h 12 m 25 s
Join Date and Time............................... Mon Jan 12 12:55:07 2015
Join Taken Time.................................. 0 days, 00 h 01 m 15 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_DISABLED
Operation State ............................. DOWN
Operation State Down Cause................... Radio is exiting inline CDP low power mode holddown.
Operation State Down Code.................... RADIO_RC_EXIT_LOW_PWR
Radio Role .................................. ACCESS
Radio Mode .................................. Remote
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 1
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:23:eb:dc:c6:90
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
MCS Set
MCS 0.................................... SUPPORTED
MCS 1.................................... SUPPORTED
MCS 2.................................... SUPPORTED
MCS 3.................................... SUPPORTED
MCS 4.................................... SUPPORTED
MCS 5.................................... SUPPORTED
MCS 6.................................... SUPPORTED
MCS 7.................................... SUPPORTED
MCS 8.................................... SUPPORTED
MCS 9.................................... SUPPORTED
MCS 10................................... SUPPORTED
MCS 11................................... SUPPORTED
MCS 12................................... SUPPORTED
MCS 13................................... SUPPORTED
MCS 14................................... SUPPORTED
MCS 15................................... SUPPORTED
MCS 16................................... DISABLED
MCS 17................................... DISABLED
MCS 18................................... DISABLED
MCS 19................................... DISABLED
MCS 20................................... DISABLED
MCS 21................................... DISABLED
MCS 22................................... DISABLED
MCS 23................................... DISABLED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 6
Tx Power Assigned By ...................... DTPC
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 11
Channel Assigned By ....................... DCA
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
TI Threshold .............................. -50
Legacy Tx Beamforming Configuration ....... AUTOMATIC
Legacy Tx Beamforming ..................... DISABLED
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
802.11n Antennas
A....................................... ENABLED
B....................................... ENABLED
C....................................... ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... Viten_1142_2
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 13
MAC Address...................................... 00:22:bd:19:d5:80
IP Address Configuration......................... DHCP
IP Address....................................... 192.168.162.110
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 192.168.162.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Enabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Floor Label............................. 0
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................ Viten_2504
Primary Cisco Switch IP Address.................. 192.168.162.20
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... FlexConnect
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... system
S/W Version .................................... 7.4.130.2
Boot Version ................................... 12.4.18.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
Stats Collection Mode ........................... normal
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1142N-A-K9
AP Image......................................... C1140-K9W8-M
IOS Version...................................... 15.2(20150109:075323)$
Reset Button..................................... Enabled
AP Serial Number................................. FTX1332SBYY
AP Certificate Type.............................. Manufacture Installed
FlexConnect Vlan mode :.......................... Disabled
FlexConnect Group................................ Not a member of any group
Group VLAN ACL Mappings
FlexConnect Local-Split ACLs :
WLAN ID PROFILE NAME ACL TYPE
Flexconnect Central-Dhcp Values :
WLAN ID PROFILE NAME Central-Dhcp DNS Override Nat-Pat Type
4 test123 False False False Wlan
FlexConnect Backup Auth Radius Servers :
Primary Radius Server........................... Disabled
Secondary Radius Server......................... Disabled
AP User Mode..................................... CUSTOMIZED
AP User Name..................................... admin
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 10.6.0.25
AP Up Time....................................... 1 days, 02 h 13 m 41 s
AP LWAPP Up Time................................. 1 days, 02 h 12 m 25 s
Join Date and Time............................... Mon Jan 12 12:55:07 2015
Join Taken Time.................................. 0 days, 00 h 01 m 15 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211n-5
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
Radio Mode .................................. Remote
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 1
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:23:eb:dc:c6:90
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
MCS Set
MCS 0.................................... SUPPORTED
MCS 1.................................... SUPPORTED
MCS 2.................................... SUPPORTED
MCS 3.................................... SUPPORTED
MCS 4.................................... SUPPORTED
MCS 5.................................... SUPPORTED
MCS 6.................................... SUPPORTED
MCS 7.................................... SUPPORTED
MCS 8.................................... SUPPORTED
MCS 9.................................... SUPPORTED
MCS 10................................... SUPPORTED
MCS 11................................... SUPPORTED
MCS 12................................... SUPPORTED
MCS 13................................... SUPPORTED
MCS 14................................... SUPPORTED
MCS 15................................... SUPPORTED
MCS 16................................... DISABLED
MCS 17................................... DISABLED
MCS 18................................... DISABLED
MCS 19................................... DISABLED
MCS 20................................... DISABLED
MCS 21................................... DISABLED
MCS 22................................... DISABLED
MCS 23................................... DISABLED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 21
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 6
Tx Power Level 1 .......................... 14 dBm
Tx Power Level 2 .......................... 11 dBm
Tx Power Level 3 .......................... 8 dBm
Tx Power Level 4 .......................... 5 dBm
Tx Power Level 5 .......................... 2 dBm
Tx Power Level 6 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Tx Power Assigned By ...................... DTPC
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 48
Channel Assigned By ....................... DCA
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140,
......................................... 149,153,157,161,165
TI Threshold .............................. -50
Legacy Tx Beamforming Configuration ....... AUTOMATIC
Legacy Tx Beamforming ..................... DISABLED
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
802.11n Antennas
A....................................... ENABLED
B....................................... ENABLED
C....................................... ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 4
Cisco AP Name.................................... Viten_1142_1
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 13
MAC Address...................................... 00:22:90:90:df:6c
IP Address Configuration......................... DHCP
IP Address....................................... 192.168.162.117
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 192.168.162.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Enabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Floor Label............................. 0
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................ Viten_2504
Primary Cisco Switch IP Address.................. 192.168.162.20
Secondary Cisco Switch Name...................... Viten_5508_1
Secondary Cisco Switch IP Address................ 192.168.162.22
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_DISABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... FlexConnect
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... system
S/W Version .................................... 7.4.130.2
Boot Version ................................... 12.4.18.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
Stats Collection Mode ........................... normal
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1142N-A-K9
AP Image......................................... C1140-K9W8-M
IOS Version...................................... 15.2(20150109:075323)$
Reset Button..................................... Enabled
AP Serial Number................................. FTX1308S2H3
AP Certificate Type.............................. Manufacture Installed
FlexConnect Vlan mode :.......................... Disabled
FlexConnect Group................................ Not a member of any group
Group VLAN ACL Mappings
FlexConnect Loc -
Copy startup or running config from 2811 rommon
I have a 2811 that has a bad CF slot. I don't have a USB stick small enough (4GB is the smallest, unless it'll use it partitioned as a 2GB) to copy IOS to the 2811. Right now I'm trying to copy the IOS image via xmodem into DRAM and booting that way. TFTP kept failing.
If this doesn't work, is there a way to copy the startup/running-config from rommon? Even if I can just view the config that would be fine. I thought I had the config copied off of it, but can't find it for the life of me.TFTP transfers fail, I've tried it a couple of times. I'm going to try xmodem again.
I can get into priv mode, but meminfo will not give me the hex addresses needed to dump. I get the hex address of the start of the main memory, nothing else.
Edit: The xmodem download completed, but I get the same error as trying to boot from the CF card:
Error : uncompressed image checksum is incorrect 0x5D7BD774
Expected a checksum of 0x357BD795
*** System received a Software forced crash ***
signal= 0x17, code= 0x9, context= 0x80014dc0
PC = 0x8000f0d4, Cause = 0x20, Status Reg = 0x3040a803 -
Copy startup-config running-config
I am replacing a css-11150 switch. I received as version 4.01; therefore I upgraded it to version 6.10-405. The upgrade went fine.
Then I ftp the config file to the css box and copy it to startup-config. It worked ok also.
The problem started here -> when I copy startup-config to running-config, it appeared copied ok (no error message), but when I did a "sh run", the running config is empty, (no statements at all). My startup config has about 100 lines of coding. I hate to type in every single line.
Do any one running into this kind of strange problem?
thanks.I upgraded from Ver 4 to ver 6.10 using the upgrade script.
upgrade
To upload the startup-config
copy ftp
Below is the "sh start", "sh run" "sh ver",
as you can see, when I did a sh run, it returns nothing. (i deleted some lines on sh start here since it is too big to post)
CSS11150# sh startup-config
!*************************** GLOBAL ***************************
sntp server 168.38.250.142 version 1
snmp location "701 West 51 st, Austin, TX 78751 "
snmp community Shirt1 read-only
snmp contact "Network Engineer, NGIT, (512)377-2222"
ip route 0.0.0.0 0.0.0.0 168.38.131.1 1
!************************* INTERFACE *************************
interface e1
bridge vlan 12
phy 100Mbits-FD
interface e2
bridge vlan 12
phy 100Mbits-FD
interface e3
bridge vlan 12
phy 100Mbits-FD
interface e4
bridge vlan 12
phy 100Mbits-FD
interface e5
bridge vlan 12
phy 100Mbits-FD
interface e6
bridge vlan 12
phy 100Mbits-FD
interface e7
bridge vlan 12
phy 100Mbits-FD
interface e8
bridge vlan 12
phy 100Mbits-FD
interface e9
bridge vlan 12
phy 100Mbits-FD
interface e10
--Cancelled---
CSS11150# sh run
CSS11150# copy startup-config running-config
Copying(\)
CSS11150# sh run
CSS11150# sh start
^
%% Invalid input detected at '^' marker.
CSS11150# sh startup-config
!*************************** GLOBAL ***************************
sntp server 168.38.250.142 version 1
snmp location "701 West 51 st, Austin, TX 78751 "
snmp community Shirt1 read-only
snmp contact "Network Engineer, NGIT, (512)377-2222"
ip route 0.0.0.0 0.0.0.0 168.38.x.x
!************************* INTERFACE *************************
interface e1
bridge vlan 12
phy 100Mbits-FD
interface e2
bridge vlan 12
phy 100Mbits-FD
interface e3
bridge vlan 12
phy 100Mbits-FD
interface e4
bridge vlan 12
phy 100Mbits-FD
interface e5
bridge vlan 12
phy 100Mbits-FD
interface e6
bridge vlan 12
phy 100Mbits-FD
interface e7
bridge vlan 12
phy 100Mbits-FD
interface e8
bridge vlan 12
phy 100Mbits-FD
interface e9
bridge vlan 12
phy 100Mbits-FD
interface e10
bridge vlan 12
phy 100Mbits-FD
interface e11
bridge vlan 12
phy 100Mbits-FD
interface e12
bridge vlan 12
phy 100Mbits-FD
interface e15
bridge vlan 12
phy 100Mbits-FD
description "Link to PRSSWINTERS1-7/21"
interface e16
phy 100Mbits-FD
description "Link to PRSSWINTERS1-7/1"
!************************** CIRCUIT **************************
circuit VLAN1
ip address 168.38.x.x 255.255.255.128
circuit VLAN12
ip address 168.38.x.y 255.255.255.128
!************************** SERVICE **************************
service Web29-tare.dfps.state.tx.us
ip address 168.38.49.122
protocol tcp
port 8010
keepalive type tcp
service Web29-tarefile.dfps.state.tx.us
ip address 168.38x.x
protocol tcp
keepalive type tcp
port 8010
service iws-86
protocol tcp
ip address 168.38.x.x
keepalive port 80
keepalive type tcp
active
content www.txabusehotline.org
add service www.txabusehotline.org-113
vip address 168.38.x.x
protocol tcp
advanced-balance sticky-srcip
active
CSS11150#
CSS11150# sh run
CSS11150# sh version
Version: ap0610405 (6.10 Build 405)
Flash (Locked): 4.01 Build 32
Flash (Operational): 6.10 Build 405
Type: PRIMARY
Licensed Cmd Set(s): Standard Feature Set
CSS11150#
CSS11150#
Maybe you are looking for
-
I've been working on an ibook in author now for 2 months. I've had some upds and downs with the format, but finally have a product that's close to finished. I updated my ibooks author software to 1.1 yesterday and now I can't open my file. Please hel
-
In Flex Mobile Release Build arguments.callee cause crash
This is my code in a simpler way: In my main MXML: private var applicationData:AppData = AppData.getInstance(); My AppData Class package { public class AppData { private static var instance:AppData; public function AppData(caller:
-
Is the small email viewing window in Mail, the same as actually opening an email?
I'm wondering if opening Mail, clicking once on an email, which then appears in the small box, is like actually opening an email in a window (two clicks)? It's problem considered a stupid question, but I want to know.... I think that it's just like a
-
Hi everybody I need to write a simple query result to a xl format file, how can I do that?
-
My 2001 version of Photoshop elements stops during installation.
Installation seems fine at first, then I get error message ' requires Internet explorer 4 or higher' then it exits, I have the latest IE on my computer! I have had this version forever and have installed it on my computers over the years with XP, Vi