Vlan traffic is not passing through Wireless Bridge

Hi,
Recently we have placed wireless bridge in our network (Cisco AIR-BR1410A-E-K9 model). Now after installing the bridge we are facing the issue like only the management interface traffic is reachable through bridge, but not able to reach other vlan traffic.
like management range is in vlan 1 (which inlcudes AP' Switch and router) and the bridge IP's are also in Vlan 1.
Switch port is kept in trunk mode both ends of bridge. still other vlan traffic is not reachable, do we have to place any special configuration for this ?
all the business users are in Vlan 3
all the sale team users are in vlan 123.
now problem is other end switches are reachable for me through bridge that is in vlan 1, but vlan 3 and vlan 123 are not reachable for me.users are not getting IP's, when we assigned the static ip address and tested still it is not working.
i am attaching my wireless bridge configuration in the discussion, please help on this issue.
Root Bridge ---- Non--Rootbridge--- Cisco Switch--Cisco Switch..
now i am able to those two switch also, but not able to reach the vlan 3 users who are connected to that switches.

Hi,
infrastructure-ssid has been placed at both end still not able to get IP's to the devices.
I am not able to attach txt files in the reply, could you please let me know your email ID so that i will send the config files to your ID.

Similar Messages

GRE traffic can not pass through LRT224 IPSec Tunnel

Hi,
We have a trouble when using Cisco Router GRE tunnel plus LRT224 IPSec Gateway-Gateway Tunnel.
We found after reboot, GRE packets can not pass trough LRT224 IPSec tunnel. need to restart serval time then gre will back to normal.
Besides that, GRE keepalive packets can not pass trough LRT224 IPSec Tunnel.
please help. I had tried to upgrade to latest firmware version.
Firmware Version : v1.0.3.09 (Dec 26 2014 14:28:46)
A-END:
interface Tunnel1
ip address 10.216.80.105 255.255.255.252
ip mtu 1400
ip nat outside
ip virtual-reassembly in
ip tcp adjust-mss 1360
ip ospf network point-to-point
ip ospf hello-interval 3
ip ospf cost 10000
tunnel source 10.216.81.2
tunnel destination 10.216.80.90
end
B-END:
interface Tunnel11
ip address 10.216.80.110 255.255.255.252
ip mtu 1400
ip tcp adjust-mss 1360
ip ospf network point-to-point
ip ospf cost 10000
ip ospf hello-interval 3
tunnel source 10.216.80.91
tunnel destination 10.216.81.3
end
CISCO2911 <> LRT224 <> INTERNET <> LRT224 <> CISCO 2621
San

Can you post the results from the below command for the Cisco Routers?
IOS Command: "sh version"
Why not static route without NAT through the LRT224 IPSec VPN?
Just curious why did you use LRT224's for the Site to Site VPN instead of the Cisco Routers?
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

WLC not pass DHCP past bridged units

I have a WLC 5508 with LWAP 1242 with wireless bridges connected to the APs I cannot get DHCP to pass through the bridge to the PC connected to the bridge.

Some third-party WGBs need to operate in non-DHCP relay mode. If problems occur with the DHCP assignment on devices behind the non-Cisco WGB, use the following commands:
–config dhcp proxy disable
–config dhcp proxy disable bootp-broadcast disable
The default state is DHCP proxy enabled.
the above commands introduced from 7.0.116.0.

I can not make a wireless bridge in the band 2.4 Linksys wrt1900ac

I can not make a wireless bridge in the band 2.4 I make the same settings on band 5 and runs perfect

I'd check to see if the 1900AC can bridge two WiFi connections at the same time. It may only beable to bridge one or the other radio at a time. I know that with the 5Ghz radio is bridged on the 1900AC, the 2.4Ghz radio is running and working as a wireless AP.

Cisco 300 - VLAN DHCP packets not passing

I am seeing a problem with our Cisco 300 switches. We use these switches as access switches, with a stacked 3750-G at the core, two 2960-S at the distribution layer, and about 10 300 Series switches at the access layer (10 port and 28 ports, all PoE).
We use Voice VLAN (VLAN 14) for our Mitel phones – there is a DHCP server on the Mitel system. Phones come up, get tagged VLAN 14 (LLDP), Traffic flows (including Broadcast for DHCP etc…). The system works, and has worked for months.
One day, suddenly, I find that all the Mitel phones on a particular access switch are not working. I look on the Mitel system and the lease on DHCP has expired, and the phone is stuck on renewing its DHCP IP address. I run port mirroring on the switch for VLAN 14 to see what is happening. The phones are stuck on DHCP discover, and I see the DHCP Discover broadcast packets on the switch but nothing else, no DHCP offer packets – hence the phone stuck at boot cycle.
I then do a port mirror from another access switch (that is currently working) – I can see the broadcast packets from the Mitel phones on the broken switch, but on this switch I can also see the DHCP offer packets from the Mitel system. I run two port mirrors simultaneous from the two switches (one working, one not) and I can see that the DHCP offer packets are not coming through to the broken switch. Panic ensues – I look at the distribution layer and there is no problem what so ever.
For some strange reason, the Cisco 300 28 port has stopped passing DHCP broadcast packets on a particular VLAN, even though they are being sent. I power cycle the switch – and hey presto, DHCP offer packets are coming through, and the phones get an IP address and boot properly.
I wipe the sweat off my brow, note the issue down and carry on my daily duties.
Forward a couple of weeks later, and to today. I have another phone that is showing the same symptoms, luckily it is the only phone on this particular Cisco 300 28 port. The same issue is occurring as described above. I gather as much diagnostic information I can then reboot the switch – but still no joy. I then remember that this switch is not directly attached to the distribution layer and instead gets trunked to another Cisco 300 28 port. I give that a reboot and 5 minutes later, DHCP broadcast offers are passing and the phone boots.
I am listing this problem as not just a ‘one off’ now, and is recurring. It has happened to two of my 300 28 port switches.
All Switches running 1.1.2.0.
No link to up time – first instance of the problem, switch was up for 14 days – second instance (another switch) uptime of 39 days
LLDP is working fine on the switches, as is Voice-VLAN (Port is tagged and broadcasts out DHCP Discover which is seen by other devices throughout network)
Nothing in the log file on the access switch
Nothing on the Dist/Core regarding STP – Spanning tree set up is fine throughout
Has anyone else experienced same? I’m hoping this is a bug that is getting fixed.
Many Thanks
Tim

Hello Tim
Brayton Hackworth had a similar post as yours, found here;
https://supportforums.cisco.com/message/3684179#3684179
Brayton is using the Mitel 5330 phones where the LLDP no longer fed VLAN information to the phone network. But, he reverted to use a DHCP server to provide the VLAN information.
Unfortunately, I (personally) cannot test any Mitel resources (since I don't have them) so my labs usually only consist of either 7900 series or SPA500/900 series phones.
The best thing I can really recommend to you is to make a package of data consisting of;
Topology which consists of;
Modem type
Router including IP
All devices including IP of switches
Servers / relevant workstations
# of attached devices and # of users on the LAN
Switch config file + show tech on a notepad
Syslog output from the switch
Working PCAP
PCAP showing failure
PCAP legend showing what IP address are who (unless topology contains all IP)
Where the PCAP is taken from and method
We then can create a service request for you and pass it for review.
-Tom

Web server return traffic does not go through ACE

Hi ,
I had configured ACE for my web servers ,
when i tried to hit VIP of webserver, return traffic directly tries to hit client.
Is there any command to instruct ACE (like group in CSS) for same.
Thanks
Aniruddha

Are you running ACE in routed/Bridge mode? If you are running it in routed mode then make sure that server side vlan SVI is not configured on MSFC.
When you configure a source group in CSS, a CSS provides network address translation (NAT) of source IP addresses and port address translation (PAT) of source ports.
This can be achieved in ACE as well
class-map nat
match source-address any
policy-map multi-match nat
class nat
nat dynamic 1 vlan 100
interface vlan 20 <-- Client Vlan
ip address 10.20.10.1 255.255.255.0
service-policy input nat
interface vlan 100 <-- Server Vlan
ip address 10.10.10.100 255.255.255.0
nat-pool 1 10.10.10.18 netmask 255.255.255.255 pat
With the above config all traffic will be source nated to 10.10.10.18 before hitting the real server. Return traffic from servers will be destined to 10.10.10.18 and as a result will end up to ACE.
Hope it helps
Syed Iftekhar Ahmed

Environment variables not passed through to player in flexunit 4.1.0-beta3

fyi, to get flexunit-4.1.0-beta3 FlexUnit4AntTasks invocation of flashplayer to not be rejected by the vncserver, i needed to modify the FlexUnitLauncher to pass through the environment variables to the command environment.
the reason this is required, i think, is the use of Runtime.exec() directly in CustomPlayerCommand -- in flexunit-4.0.0, the same function was accomplished using the ant executor, which does passthrough by default.
anyway, curious if anyone else has seen this issue, or if i'm doing something dumb.
--- flexunit/flexunit-4.1.0-beta3/flexunit-flexunit-da29198/FlexUnit4AntTasks/src/org/flexuni t/ant/launcher/FlexUnitLauncher.java    (revision 7250)
+++ flexunit/flexunit-4.1.0-beta3/flexunit-flexunit-da29198/FlexUnit4AntTasks/src/org/flexuni t/ant/launcher/FlexUnitLauncher.java    (revision 7251)
@@ -79,7 +82,13 @@
       command.setSwf(swf);
       if (runHeadless())
-         command.setEnvironment(new String[]{ "DISPLAY=:" + xvncStart.getCurrentDisplay() });
+         Map<String, String> env = System.getenv();
+         List<String> envArgs = new ArrayList<String>();
+         for (Map.Entry<String, String> entry : env.entrySet()) {
+            envArgs.add(entry.getKey() + "=" + entry.getValue());
+         }
+         envArgs.add("DISPLAY=:"+xvncStart.getCurrentDisplay());
+         command.setEnvironment(envArgs.toArray(new String[0]));
          LoggingUtil.log("Setting DISPLAY=:" + xvncStart.getCurrentDisplay());

ok. i went looking for a JIRA link somewhere around here and couldn't find it. do you have a URL handy?
there are a couple of other things too:
you probably want trustDirectory.mkdirs() rather than mkdir() in TrustFile.java
you probably want CustomPlayerCommand.setLocalTrusted() -- my player command isn't in the machine's path, but i still want to be able to touch the trust file. So I copied the trustFile.add() stuff from FlashPlayerCommand.launch() into CustomPlayerCommand.launch(). probably a better solution would be refactoring CustomPlayerCommand to be more like FlashPlayerCommand.
anyway, if you want patches, tell me where to put them and i'll post some.

Guest LAN and DHCP Options not passing through

Managed to get the Guest LAN up and running for wired clients and all's working well. Users are sat behind a proxy and if I force the use of a appropriate wpad file I can get the WLC auth to happen and then push off to the proxy.
I'm trying to use option 252 in DHCP to present the WPAD url. Only issue that happens is that while the DHCP server on the egress interface is handing out addresses to clients on the ingress interface correctly, the WLC doesn't appear to be handing through the option 252 I have set in DHCP. I've used network monitor to see what the dhcp request process is dishing out in terms of options, and all look good if I'm not behind the WLC.
Anyone know if theres a limitation on the WLC that prevents DHCP options being passed through to the guest LAN?
TIA

When configured as a DHCP server, some of the firewalls do not support DHCP requests from a relay agent. The WLC is a relay agent for the client. The firewall configured as a DHCP server ignores these requests. Clients must be directly connected to the firewall and cannot send requests through another relay agent or router. The firewall can work as a simple DHCP server for internal hosts that are directly connected to it. This allows the firewall to maintain its table based on the MAC addresses that are directly connected and that it can see. This is why an attempt to assign addresses from a DHCP relay are not available and the packets are discarded. PIX Firewall has this limitation.
For more information please refer to the link-http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008070ba8f.shtml

MF4890dw not scanning through wireless with win7,win8.1 or OSX 10.9

I use iMac with OSX 10.9.2. I installed latest version of MF Toolbox, upgraded the firmware to 15.04. I can scan with USB. Wireless works because I can print with wireless. However, when I disconnect USB and try to scan through wireless network, either from iMac or from MF4890dw, it will scan the first page and hangs for a while, then MF2890 will show "An error has occurred [close]" and the computer will pop up an error window:
"Cannot communicate with the scanner.
The cable may be disconnected, or the scanner may be turned off.
Check the scanner status and try again.
Scanner driver will be terminated.
Error code: 200010"
When I use with win 7- 64 or win8-64, I also get the same question.
"Cannot communicate with the scanner.
The cable may be disconnected, or the scanner may be turned off.
Check the scanner status and try again.
Scanner driver will be terminated.
Error code: 155 0 0"
Any help is appreciated.

Same problem here, with Windows 7. Appeared out of nowhere. Reinstalling drivers and MF Toolbox did not help.

MF4890dw not scanning through wireless

I use iMac with OSX 10.9.2. I installed latest version of MF Toolbox, upgraded the firmware to 15.04. I can scan with USB. Wireless works because I can print with wireless. However, when I disconnect USB and try to scan through wireless network, either from iMac or from MF4890dw, it will scan the first page and hangs for a while, then MF2890 will show "An error has occurred [close]" and the computer will pop up an error window:
"Cannot communicate with the scanner.
The cable may be disconnected, or the scanner may be turned off.
Check the scanner status and try again.
Scanner driver will be terminated.
Error code: 200010"
MF4890dw is communicating with iMac because it will scan the first page and it will tell me to put paper in the feeder.
Any help is appreciated.

I'm having the same error on my 4880 wireless. It previews the scan but it comes up with that **bleep** error. Why hasn't the tech responded? Clearly his generic answer didn't help.

Pass Through Theme Still Not "Passing Through"

So I'm working on this project and it looks completely AWESOME on my computer with the "pass through" theme, but when I burn it to DVD I just get a blurry picture behind a "white" scrolling title. I know this has been addressed before and I've checked out all the "fixes" so far on this issue from past topics but I'm still pulling my hair out.
I've tried "deleting my preferences" and "repairing my permissions" but still end up with the same thing... a white scrolling text over a blurry picture. My Mac is only 2 months old!
Perhaps the solution is to just fly my family out to watch the dvd on my computer???
Help! Anyone? Bueller?

Nevermind!
I went back to an awesome answer by Rich839 who suggested the following:
+Sometimes permissions and preferences can get corrupted. Whenever iDVD starts acting funny, a common maintenance procedure is to do the following: Delete preferences by closing iDVD and trashing the file com.apple.iDVD.plist found in User (the House icon)/Library/Preferences. Then do a permissions repair using the Utilities/Disk Utility App on your Mac. Open the Disk Utilities window and select the Mac hard drive icon at the top of the side pane at the left. Then click on the Repair Permissions button. When you have repaired permissions and deleted preferences, restart your computer and launch iDVD. iDVD will replace the .plist file that you deleted. Be sure also that you have sufficient free disk space on your hard drive for iDVD to function correctly. 25GB often is recommended by users of this forum. After doing all of the above, relaunch iDVD and see whether you still have the problem.+
I failed to restart my computer after deleting and repairing, but after I did the above seemed to work! *crosses fingers* At least the "Pass Through" feature seems to be working in the little preview window while it's burning. Before, the scrolling text in the preview window was just white!
Hope this somehow helps others who've had the same issue!

Traffic not passing through firewall

Ive got a problem with passing traffic through a Cisco 515e firewall.
im trying to telnet to devices on the inside net, 172.16.x.x fom an outside net 10.x.x.x
ive configured a group called infrastructure and added the 10.x.x.x addresses.
ive configured acl 101 inbound on the outside interface:
access-list 101 permit tcp object-group INFRASTRUCTURE any eq telnet
theres a route to the inside net:
inside 172.16.0.0 255.255.0.0 172.16.163.1
and theres a translation:
static (inside,outside) 10.4.4.34 10.4.4.34 netmask 255.255.255.255
when i try and connect, using a packet capture I can see traffic from 10.4.4.34 to the inside device 172.x.x.x on the inside interface but i cant see the traffic leave the outside interface
ive used the same group infrastructure group before to connect to VM machines on the 172.x.x.x net on RDP and this wrks ok.
access-list 101 permit tcp object-group INFRASTRUCTURE object-group VMs eq 3389
does anyone have any idea what is wrong?

Hi Michael,
Please post the output from below command.
packet-tracer input outside icmp 10.4.4.34 8 0 172.16.163.7
You may have to allow icmp travers temporarily on the ACL 101, to check the reachability.
Look forward to hear from you.
thanks
Rizwan Rafeek
Message was edited by: Rizwan Mohamed

HP Photosmart Plus e-All-in-One Printer B210e Does Not Print Through Wireless

I am using Mac OS X 10.7.3 on a wireless connection. I went to print, HP Utility gave me the following error message:
The printer may not exist or is unavailable at this time
It was not being used by anything else at the time. Then 2-3 minutes after I got that first error message HP Utility gave me another error message:
The printer is not responding
Then on the printer touch screen display I touched the wireless icon, chose Run Wireless Network Test, and got an error message:
Load paper into Main Tray.
The tray had plain white paper (10-15 sheets) in a nice neat stack as far back as it would go. I took the stack just to be sure it was still in a neat stack and put it in as far as it would go and pressed OK on the touch screen display and I still got the same message. Then I decide to turn the printer off using the power button, waited about a minute, and then pressed the power button to turn it on. When I did I got another error message:
Improper Shutdown
To avoid damage, use On button to shut down. Do not unplug the power cord or turn off the power outlet to shut down the device.
How is that an improper shutdown when I did use the power button to turn it off. Why is it telling me that I need to use the power button to turn it off then back on when I did use the power button to do that. What is the issue and how do I fix it. I did not have this issue with Mac OS X 10.7.2, but I do now agter the 10.7.3 update. As of right now the only way I can print from Mac OS X is using a USB connection. I can print through a wireless connection using my Windows 7 partition on the same MacBook. I am starting to think that this printer is not Mac OS X 10.7 Lion compatible.
I have a Time Capsule (3rd Generation) with the current firmware for it and the current the current AirPort Utility for Mac OS X installed.

SthrnDixieCowgirl wrote:
I don't know how to remove and add printers unless I had to format my hard drive for a completely different reason and reinstalled the printer that way.
To remove the printer, open System Preferences > Print & Scan. You will see the HP in the Printers list. Click on it once to select it and then press the minus button under the Printers list to remove it.
With this done, click the plus button under the Printers list to add the printer. With the Add Printer window open and the Default view selected, the HP should appear in this view. Select it and the Print Using menu should change to the supporting printer driver. When this happens, click the Add button to complete the creation of the printer queue.
SthrnDixieCowgirl wrote:
I have heard other people have issues with 10.7.3 for other reasons and I should have waited until 10.7.4 came out before updating and I didn't and now there is nothing I can do to go back to 10.7.2
You cannot believe everything you read. For every person that had a problem after installing the .3 update, a hundred more had no problem.
But if you wanted to go back to 10.7.2, then you can use Time Machine to do this. If you are not using Time Machine then you need to start doing so. At least the update only stopped you from network printing. What if it had stopped you from using the Mac?

HT4241 Audio not passing through

I purchased my MiniDisplay port to HDMI adapter from Apple and it doesn't pass the audio through. It doesn't make sense to me that they would sell an adapter that doesn't work like the article above describes. Any advice? Am I missing something?

The adaptor almost certainly works as described. How old is your MBP? MBPs earlier than mid-2010 do not support audio through the mini-displayport - as described in the article you reference. If your MBP is a recent one, then option click on the speaker icon on the menu bar and check under 'Output device'.

Itunes Server (Synology 107+) not seen through Wireless sharing.

I have set up all my music on a server (Synology 107+).
But I can not see my music folder via Itunes over the wireless.(Airport Extreme).
I can see it if I am connected on the ethernet.
What am I doing wrong?
I HAVE GONE to preferences and checked "look for shared libraries"
I HAVE GONE to sys pref/sharing/file sharing. And turned it on.
What else is there?
Why would it see through the ethernet (and play Great) but not wireless.
ALSO I CAN mount the music folder on the server via wireless but just not in itunes.
Any insight would be great.
Also: I have a ATT Uverse Router. The Airport is hooked to the Router as is the Synology 107+ server.
thanks

I have the same issue - can use AirPlay with wired devices - wireless is hit or miss; mostly miss... Using Netgear WNDR3700v2. Did you fix the issue?
Anyone else has any advice?

Vlan traffic is not passing through Wireless Bridge

Similar Messages

Maybe you are looking for