VM-605 auto redials when pressing the front panel.
I just got this VM-605 for my Bold 9700 and when I follow the instructions to Press and hold the front panel until you heaer a beep... to make a call, the VM-605 automatically redials the last called number rather than listening for my command.
Anyone come across this?
From reading this forum, this product seems like a real hit and miss.
Hey curtistimmer,
You may find some useful information in the following post.
http://supportforums.blackberry.com/t5/BlackBerry-Accessories/VM-605-FAILURES/m-p/434678
Have a look at the post by dannytobin
<snip>
07-07-2010 02:05 PM
I have just encountered a problem with my vm-605 whilst toying around with it. The thing froze up and all the lights come on.
If you look at the back of the device just to the left above the label is a hole. Gently poke with a paperclip until you here a faint click.
This has fixed my problem!!
<snip>
Let us know if this works for you.
-SR
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!
Similar Messages
-
What should I do if I want to display on the front panel in real time the values from Polarizer #, P1, P2 and the last calculated value (P2/P1 * 100) called T% in a table or some graphical representation like that? What would I have to do? It could just be Polarizer # and T% if that would be simpler. I just want to let the user know the values in a list, spreadsheet or table as they go. One last thing is that I would like to be able to stop the program at any point in time as soon as the stop button is pressed. As of now, when the button is pressed it goes through the iteration currently in progress and then one afterwards. I want the program to end as soon as the stop button is pressed no matter what sequence it is. What can I do to achieve this? Could you give me an example or modify my program to show me this.
Thanks,
Steve
Stephen Coward
Northrop Grumman
[email protected]
Attachments:
EPM2000 almost done.vi 50 KBPut a single frame sequence structure around your stop button and then wire from the error cluster going into the error handler to the edge of the sequence structure. Now your code will stop at the end of the current iteration. To see why this works, watch you code execute with execution highlighting turned on and review the section of the manual talking about "Dataflow".
Mike...
Certified Professional Instructor
Certified LabVIEW Architect
LabVIEW Champion
"... after all, He's not a tame lion..."
Be thinking ahead and mark your dance card for NI Week 2015 now: TS 6139 - Object Oriented First Steps -
How to see the full program on the front panel when it is running?
Hi, my program is really big, and when I run it and obverserve the program on the front panel, I cannot drag the window to see the other parts. Also, I tried the method like hold control, then press + to zoom in or press - to zoom out. However, labview seems doesnt have this function. Does anyone know how I can see the full program then it is running, maybe zoom out or drag the windows? thanks!
Attachments:
not running.png 85 KB
running.png 72 KBYou should use a Tab control. Group your front panel objects together and put the grouped items in tabs. Then you can select the Tab you want to display while the program is running.
It is never a good idea to make your screen too big to fit on one display. This goes for the block diagram also. If you have to scroll to see it all, use more subvi's. Make it modular. A state machine is a good way to put a lot of code on one display screen.
- tbob
Inventor of the WORM Global -
Having several windows appear ...
Hi,
You can't create several windows for one VI. But you can use the "Tab Control" and change tab's in the program. Or you can use sub VI's and show ther front panels.
To show the front panel of a sub VI you have to open the VI you want to show and select "File->VI Properties". In the VI Properties window select Category "Window Appearance" and click Customize...
In the Customize Window Appearence window, here you can set a number of attributes for how the window will appear, select "Show front panel when called" and "Close afterwards if originally closed" click OK and OK and save the VI, done.
Now the VI front panel will appear then you use it as a sub VI.
/Thomas -
My mini ipod appears off and not respond to any commands when pressed the buttons to reset, apple logo appeared and then the apple support site and it shuts down. already tried all the steps, but none worked, and when I plug it into my computer it does not appear in the iTunes bar. what do I do?
If MacKeeper corrupted the Recovery partition then even I underestimated its potential for damage. Garbage "cleaning" apps will cause misery but I have not found that the Recovery partition to have been affected by using MacKeeper or anything like it. I doubt that it did so, but I have learned not to underestimate the potential for such things to result in system corruption.
Before concluding your Mac has a hardware failure, try booting OS X Internet Recovery by holding command option r on startup (three fingers). That will force your iMac to bypass the Recovery partition altogether, and convey the ability to create a new one.
An Internet connection will be required (wired or wireless).
At the Mac OS X Utilities screen, select Disk Utility. Select your startup volume (usually named "Macintosh HD") and click the Repair Disk button. Describe any errors it reports in red. If Disk Utility reports "The volume Macintosh HD appears to be OK" in green then you can be reasonably (though not completely) assured your hard disk is in good working order.
Assuming the HD remains usable you can then use Disk Utility to erase it. Reinstall OS X, restore your essential software and other files, and don't reinstall the junk. -
Analog output to the DAQ that changes when controls on the front panel change
I'm using the PCI-6024E, and trying to output an analog waveform that can change when one of the two controls on the front panel change. It outputs fine setting it to continuous output and using a simple while loop around the "Is Task Done" VI, but if I put the "Write" VI in the while loop, it doesn't output steadily. I then tried to use an event structure, so that I'd only have to write every time something on the front panel changes, but for some reason it was writing finite samples, even though I set the Timing VI to continuous. I looked around the NI site, and found an article about this with an example. I tried to change it around to use my waveform, but whenever I run it, I get a memory underflow error. Has anyone needed to do this before? Thanks in advance.
-- Josh MatloffHi Josh-
It looks like you forgot to post the code still, but I'll take a stab at the problem anyway. It sounds like you're looking for a way to update a continuous waveform at runtime.
You will need to stop the task in order to replace the write buffer information, but this will only be a small gap in operation. I have attached a modified LabVIEW shipping example that shows how to use value change events for any of the pertinent waveform parameters to either programmatically stop the task, replace the buffer, set timing and restart or to just pass the task information straight through. This will lead to continuous operation with no breaks at the output.
Please let us know if this clears up your questions.
Thanks-
Tom W
National Instruments
Attachments:
Cont Gen Voltage Wfm-Int Clk with Runtime Update.vi 134 KB -
my apps are not being updated when pressing the update all button. It just says installing and no update is being done., my apps are not being updated when pressing the update all button. It just says installing and no update is being done.
Must be serious because you have stated the problem 4 times now.
Here are a number of things that you can try and maybe one of them will help.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.
Make sure that you do not have a stalled download in iTunes - a song or podcast .... if you have a download in there that did not finish, complete that one first. Only one thing can download at a time on the iPad so that could be what is causing the problem.
If that doesn't work - sign out of your account, restart the iPad and then sign in again.
Settings>iTunes & App Store>Apple ID. Tap your ID and sign out. Restart the iPad by holding down on the sleep button until the red slider appears and then slide to shut off. To power up hold the sleep button until the Apple logo appears and let go of the button.
Go back to Settings>iTunes & App Store>Sign in and then try to update again. Tap one waiting icon only if necessary to start the download stream.
You can also try deleting the waiting icons - tap and hold down on an icon until it wiggles - the tap the X on the icon to delete it. Then try to download again.
You can try resetting all settings. Settings>General>Reset>Reset All Settings. You will have to enter all of your app preferences and device settings again.
You can also try going to the App Store, find an app that needs an update, tap on the app icon to bring up the description page, then tap on install that way, rather than using the Update option from the app updates screen.
And ... You can always install the updates in iTunes on your computer and then sync them to the iPad. -
Looking for a way to programmatically set the visible portion of the front panel when a subVI opens
I am looking for a way to programmatically set the visible portion of the front panel when a subVI opens. Haven't found any posts that relate, but I'm not sure how to ask the right question. To be clear, I want to write a helper VI to go through a list of subVIs to make sure the background images are all in the same place when their respective subVIs open. I hate manually playing with scroll bars before I save each of the VIs... I'm figuring I need to find the top/left location of the background image (know how to do this already) and then set a VI FP property to these values or some offset, but I can't find the relevant property. FP:run-timeposition:custom looked promissing, but only affects the location of the window, not the area of the front panel the window is displaying.
Solved!
Go to Solution.Cool. Getting closer. The way I implemented your suggestion affects the subVI only if it is open. I can use this to do what I'm after, perhaps putting the code into each subVI. Maybe open all subs, run the helper, and save. Seems like I'm missing the elegant version...
My proof of concept code: -
HELP. How do I lock a line to a shape so it will auto extend when dragging the shape?
How do I lock a line to a shape so it will auto extend when dragging the shape? I cant figure out how to turn this feature on and off.
Edit: JET got there first but I believe your problem is not as complex as he would have you believe :-)
Complex? What is simpler for the user than being able to connect pre-shaped text frames (not limited to Illustrator's silly Convert To Shape options) with rules, and then be able to move the text frames and have the rules auto-adjust (automatically avoiding other objects, automatically reshaping right-angle bends, etc. etc,) accordingly. What's "complex" about drawing a flowchart?
One can properly construct a dozen such diagrams in a program that provides proper connector lines in the time it takes to fuss and twiddle with Illustrator for such a simple task. FreeHand, Draw, Canvas, Visio all provide connector lines features.
The diagramming features in the draw module of Open Office is as good as any of them for the purpose of mundane decision tree diagrams, org charts, and flowcharts; and OpenOffice can be had for free. The same is true of Inkscape. You can download and install either one in less time than it will take to build a single typical such diagram in Illustrator. Using such tools is vastly more intuitive for a beginner than futzing about with Illustrator's "direct selection" routines.
JET -
How to run a subVI without poping up normally, but when clicking a button, popup the front panel?
I know pop-up the front panel of a subVi when called by selecting VI Properties>>Windows apperence.
But what I need to do is: always run the SubVI inside the parent VI as the nornal subVI do without poping up. But when I click a button"show front panel", the SubVI popup the front panel.
Is there anyway to do this?
Thanks,ossoo,
You can use a static VI reference to the subVI and then use the Front Panel Open invoke method to show the front panel when you want. I have attached two VIs that show this. I saved these VIs for LabVIEW 2009 so you should be able to open them up and run them in 2009 or later. Add.VI is the subVI that you are calling. The Caller.VI is just a While Loop that contiually calls the Add subVI. Inside of the While Loop is also a Case Structure with a Static VI Reference (you might need to change the path this is pointing to after downloading the VIs to your computer for this to work) and the Front Panel Open invoke method. You can run the Caller.VI and interact with the main Front Panel as normal and see the subVI but then you can click the Open subVI? boolean button and it will open the subVI's front panel. You can continue to interact with the main front panel and see the values update on the subVI's front panel as well. You can just close the subVI's front panel when you are done viewing it. Does this help?
Grant H.
National Instruments
LabVIEW Product Marketing Manager
Attachments:
Caller.vi 19 KB
Add.vi 23 KB -
How to when press the button and can change the value in the table?
this is my code so far with a table and a button..how can i make it when press the button and the data in table change..
* SimpleTableDemo.java is a 1.4 application that requires no other files.
import java.awt.BorderLayout;
import java.awt.Button;
import java.awt.Color;
import java.awt.Dimension;
import java.awt.event.MouseAdapter;
import java.awt.event.MouseEvent;
import javax.swing.JButton;
import javax.swing.JFrame;
import javax.swing.JPanel;
import javax.swing.JScrollPane;
import javax.swing.JTable;
public class SimpleTableDemo extends JPanel {
private boolean DEBUG = false;
private JPanel button;
private JButton enter;
public SimpleTableDemo() {
super(new BorderLayout());
//button.setBackground(Color.pink);
//setForeground(Color.pink);
String[] columnNames = {"First Name",
"Last Name",
"Sport",
"# of Years",
"Vegetarian"};
Object[][] data = {
{"Mary", "Campione",
"Snowboarding", new Integer(5), new Boolean(false)},
{"Alison", "Huml",
"Rowing", new Integer(3), new Boolean(true)},
{"Kathy", "Walrath",
"Knitting", new Integer(2), new Boolean(false)},
{"Sharon", "Zakhour",
"Speed reading", new Integer(20), new Boolean(true)},
{"Philip", "Milne",
"Pool", new Integer(10), new Boolean(false)}
final JTable table = new JTable(data, columnNames);
table.setPreferredScrollableViewportSize(new Dimension(500, 70));
if (DEBUG) {
table.addMouseListener(new MouseAdapter() {
public void mouseClicked(MouseEvent e) {
printDebugData(table);
//Create the scroll pane and add the table to it.
JScrollPane scrollPane = new JScrollPane(table);
enter = new JButton("Press me");
//Add the scroll pane to this panel.
buildButton();
add(scrollPane, BorderLayout.NORTH);
add(button, BorderLayout.CENTER);
private void buildButton(){
button = new JPanel();
button.add(enter);
private void printDebugData(JTable table) {
int numRows = table.getRowCount();
int numCols = table.getColumnCount();
javax.swing.table.TableModel model = table.getModel();
System.out.println("Value of data: ");
for (int i=0; i < numRows; i++) {
System.out.print(" row " + i + ":");
for (int j=0; j < numCols; j++) {
System.out.print(" " + model.getValueAt(i, j));
System.out.println();
System.out.println("--------------------------");
* Create the GUI and show it. For thread safety,
* this method should be invoked from the
* event-dispatching thread.
private static void createAndShowGUI() {
//Make sure we have nice window decorations.
JFrame.setDefaultLookAndFeelDecorated(true);
//Create and set up the window.
JFrame frame = new JFrame("SimpleTableDemo");
frame.setDefaultCloseOperation(JFrame.EXIT_ON_CLOSE);
//Create and set up the content pane.
SimpleTableDemo newContentPane = new SimpleTableDemo();
newContentPane.setOpaque(true); //content panes must be opaque
frame.setContentPane(newContentPane);
//Display the window.
frame.pack();
frame.setVisible(true);
public static void main(String[] args) {
//Schedule a job for the event-dispatching thread:
//creating and showing this application's GUI.
javax.swing.SwingUtilities.invokeLater(new Runnable() {
public void run() {
createAndShowGUI();
}Cross-post:
http://forum.java.sun.com/thread.jspa?threadID=676105 -
Emails get sent in Mail when pressing the space bar whilst spell checking
Why do emails get sent in Mail when pressing the space bar whilst spell checking ?? This is beyond annoying. It's been happening for ages on my MBP. I have seen others complain and I can't understadn why this simple bug has not been fixed. Any help on this would be very much appreciated. thank you.
Hi
In composing I have Check Spelling "when I click send" selected. I tried on my iMac, my Mail account is sync'd via iCloud etc.. I got the same thing, when you hit send and review your spelling, I need to do that a lot, as well as insert missing words. As soon as you hit the space bar off goes the email. I have seen others complain of this on the google. I have now switched to check as I type but when i make a typo Mail just puts a red line under the word, it doesn't open up the Spell Checker dialog.
Is there away of resetting my Mail Apps database ? MAybe something is corrupt.
thanks. -
HT1619 menu does not appear when pressing the menu bottom from the apple remote
I got a apple remote but the menu does not appear on the computer when pressing the menu bottom!?
Prior to Lion, it used to invoke the menu of the FrontRow application. FrontRow is no longer available with Lion. The menu button will work with apple TV.
Regards,
Captfred -
How to find VI's connected terminals when controls are hidden on the front panel?
When working with a sub-VI which has terminals connected to hidden controls is there a straight-forward way to find the terminals on the block diagram?
I click on the terminal and an outline appears on the front panel but when I try to click on that outline I can not unhide the control.
The only way I have discovered to find the terminal of the connected control is just check each terminal on the block diagram which looks like it might be connected.
I'm using LV7.1 but also use 8.5.
Thanks,
DaveyBen wrote:
smercurio_fc wrote:
If I understood the premise of the question it sounds like you have controls/indicators wired to the VI connector pane, but for some reason these controls/indicators are hidden. If this is a VI you wrote slap yourself. If this is a VI someone else wrote, go slap them.
One way that you can find the terminals on the block diagram by performing a search by text. The context help will show you the names of the controls/indicators. The only problem with this approach is that if the control/indicator has the caption visible rather than the label, then the context help will show the caption, not the label.
Another method is to use scripting. Not sure if it's worth the effort for just one VI, though.
Before we get all slap-happy I have to ask...
If I have a sub-VI which is set for Print on completion and the controls in/out for the icon connector are NOT supposed to show up on the final report, isn't setting those objects as hidden a viable option?
Ben
Well, of course, Ben. My comment was not meant to be taken seriously... hence the smiley happy icon. To respond to your question in a more serious matter, though, there's always exceptions to rules. That's why they're rules - they're meant to be broken. Otherwise they wouldn't be rules. It's a strange state of the universe, isn't it? Although, one could probably just place the control behind another object. That sort of hides it, doesn't it? -
When pressing the "R" key on the keyboard to record the following pops up - "Beta-only warning message-not to be localized. Can't create record file, Please Report" I press O.K. and this pops up - "Error occurred Result= -48". Can't figure out why. First time I have every had problems> What's up with this?
a -48 error is a duplicate filename.
the first things i'd try are the oddball problems fixes:
http://www.bulletsandbones.com/GB/GBFAQ.html#oddballprobs
(Let the page FULLY load. The link to your answer is at the top of your screen)
Maybe you are looking for
-
Works fine in JDK 6.0 but not in jdk 1.5.???????
Hi all, This code converts english date to japanese date but it is working fine in english only. can any body answer why it is so. Note : No Comiplation problem in jdk 1.5 This code works fine in JDK 6.0 but not in JDK 1.5, Why.....? SimpleDateFormat
-
Itunes will not let my view any of the tabs like apps, music, tv shows, and it only allows me to view itunes u. i don't know why. i have been having this issue for a very long time now!
-
How can I send photos via email using play memories online
Hi...I'm unable to email my photos...can anyone help me please. I log on, drag my photos over click on upload...and it goes south from there
-
Hi all We have a server client setup where teh client reads from an xml feed and then passes objects representing the xml along to the server, which processes them. So two JVMs running (each with 2 threads). We are using the standard socket/ObjectInp
-
I just bought a philips fidelio docking speaker and when I plug my iPod touch 4th gen it charges but dosent play music through the speaker.