VM's state Off-Critical

Hello,
I have an issue with my Hyper-V lab.
I have disconnected my hard drives from the motherboard due to some other issues I had at the time, and now, after reconnecting the drives to the mobo, powering on the station and launching Hyper-V, all my VM's (4 in total) are shown as Off-critical.
If I try to power on a VM, I get the following error:
Failed to lock virtual machine's configuration "C:\ProgramData\Microsoft\Windows\Hyper-V\VirtualMachines\386F7A11-991F-4859-934A-A7732CC4519C.xml": 'Unspecified error"(0x80004005)
I must mention that my virtual hard disks and VM Configuration Files are on a second drive than the one where the C:\ partition is, and where, of course Hyper-V is installed.
My OS is Windows Server 2012 Datacenter Evaluation, build 9200.
Does anybody have any idea why this happened, and what I can do to get my VM's back?
Thank so much for your input and help!

Most likely the drive did not mount properly in the OS. Or the drive letter changed, or the GUID mount point changed.
Be sure that your drives are online, in the same location. And then restart the Virtual Machine Management Service service.
It sounds as if you did not shut down your VMs before doing this.
The C:\ reference is a virtual pointer to the actual configuration file.
Brian Ehlert
http://ITProctology.blogspot.com
Learn. Apply. Repeat.

Similar Messages

BPEL process state "Off"

Hi,
I had created one BPEL process which reads from FTP Remote server and writes to local file directory.
After reading from Remote FTP server I am deleting file from the server. In the remote server I had created on user to interact with FTP server with all permissions. When the BPEL process executed FTP Adapter is deleting the File successfully from remote location but BPEL state is changed to “Off”.
When I checked the logs, I found there is problem with Delete permission. Actually as mentioned above file is deleted successfully in the remote location.
OPMN logs:
<File Adapter::Outbound> Processing file : /click/xelusparts/feeds/jabilparts/outbound/process/\po_28.txt
<File Adapter::Outbound> Sending message to Adapter Framework for posting to BPEL engine: {
file=/click/xelusparts/feeds/jabilparts/outbound/process/\po_28.txt
<2007-06-11 19:00:42,677> <DEBUG> <default.collaxa.cube.engine.deployment> <CubeProcessHolder::loadAndBind> Check if process FTPRetrieveTOFileWriteProcess, revision 1.0 needs to be reloaded
<2007-06-11 19:00:42,709> <DEBUG> <default.collaxa.cube.ws> <WSDLManager::getWSDL> registered wsdl at http://dt1521-localhost.com:80/orabpel/default/FTPRetrieveTOFileWriteProcess/1.0/_FTPRetrieveTOFileWriteProcess.wsdl
<2007-06-11 19:00:42,709> <DEBUG> <default.collaxa.cube.ws> <WSDLManager::getWSDL> got wsdl at: http://dt1521-localhost.com:80/orabpel/default/FTPRetrieveTOFileWriteProcess/1.0/_FTPRetrieveTOFileWriteProcess.wsdl
<2007-06-11 19:00:42,724> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> Sucessfully sent message : /click/xelusparts/feeds/jabilparts/outbound/process/\po_28.txt to Adapter Framework.
<2007-06-11 19:00:42,724> <INFO> <default.collaxa.cube.ws> <File Adapter::Outbound> Deleting file : /click/xelusparts/feeds/jabilparts/outbound/process/\po_28.txt after processing.
<2007-06-11 19:00:42,724> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> Host name is 'DT1521-localhost.com'.
<2007-06-11 19:00:42,724> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> Reading reply from DT1521-localhost.com
<2007-06-11 19:00:42,818> <DEBUG> <default.collaxa.cube.ws> <WSInvocationManager::invoke> operation: Write, partnerLink: <partnerLink name="FileWriter" partnerLinkType="{http://xmlns.oracle.com/pcbpel/adapter/file/Write/}Write_plt">
<myRole name="null">
<ServiceName>null</ServiceName>
<PortType>null</PortType>
<Address>null</Address>
</myRole>
<partnerRole name="Write_role">
<ServiceName>null</ServiceName>
<PortType>{http://xmlns.oracle.com/pcbpel/adapter/file/Write/}Write_ptt</PortType>
<Address>null</Address>
</partnerRole>
<conversationId>bpel://localhost/default/FTPRetrieveTOFileWriteProcess~1.0/10610-BpInv1-BpSeq1.3-3</conversationId>
<properties>{}</properties>
</partnerLink>
<2007-06-11 19:00:42,834> <DEBUG> <default.collaxa.cube.ws> <WSDLManager::getWSDL> registered wsdl at D:\OraHome_1\integration\orabpel\domains\default\tmp\.bpel_FTPRetrieveTOFileWriteProcess_1.0.jar\Write.wsdl
<2007-06-11 19:00:42,834> <DEBUG> <default.collaxa.cube.ws> <WSDLManager::getWSDL> got wsdl at: D:\OraHome_1\integration\orabpel\domains\default\tmp\.bpel_FTPRetrieveTOFileWriteProcess_1.0.jar\Write.wsdl
<2007-06-11 19:00:42,834> <DEBUG> <default.collaxa.cube.ws> <WSInvocationManager::invoke> def is file:/D:/OraHome_1/integration/orabpel/domains/default/tmp/.bpel_FTPRetrieveTOFileWriteProcess_1.0.jar/Write.wsdl
<2007-06-11 19:00:42,834> <DEBUG> <default.collaxa.cube.ws> <WSIFInvocationHandler::invoke> opName=Write, parnterLink=<partnerLink name="FileWriter" partnerLinkType="{http://xmlns.oracle.com/pcbpel/adapter/file/Write/}Write_plt">
<myRole name="null">
<ServiceName>null</ServiceName>
<PortType>null</PortType>
<Address>null</Address>
</myRole>
<partnerRole name="Write_role">
<ServiceName>{http://xmlns.oracle.com/pcbpel/adapter/file/Write/}Write</ServiceName>
<PortType>{http://xmlns.oracle.com/pcbpel/adapter/file/Write/}Write_ptt</PortType>
<Address>null</Address>
</partnerRole>
<conversationId>bpel://localhost/default/FTPRetrieveTOFileWriteProcess~1.0/10610-BpInv1-BpSeq1.3-3</conversationId>
<properties>{}</properties>
</partnerLink>
<2007-06-11 19:00:42,834> <DEBUG> <default.collaxa.cube.ws> <WSIFInvocationHandler::doShortCut> Parner Property optShortCut
<2007-06-11 19:00:42,834> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> ResourceAdapterMetaData Connection Created
<2007-06-11 19:00:42,834> <DEBUG> <default.collaxa.cube.ws> <AdapterFramework::Outbound> file:/D:/OraHome_1/integration/orabpel/domains/default/tmp/.bpel_FTPRetrieveTOFileWriteProcess_1.0.jar/Write.wsdl [ Write_ptt::Write(opaque) ] - Looking up Resource Adapter JDNI location 'eis/FileAdapter'
<2007-06-11 19:00:42,834> <INFO> <default.collaxa.cube.ws> <File Adapter::Outbound> Managed Connection Created
<2007-06-11 19:00:42,834> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> Creating Connection
<2007-06-11 19:00:42,834> <INFO> <default.collaxa.cube.ws> <File Adapter::Outbound> Connection Created
<2007-06-11 19:00:42,834> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> Creating FileInteraction
<2007-06-11 19:00:42,834> <INFO> <default.collaxa.cube.ws> <File Adapter::Outbound> FileInteraction Created
<2007-06-11 19:00:42,834> <DEBUG> <default.collaxa.cube.ws> <AdapterFramework::Outbound> Instantiating outbound JCA interactionSpec oracle.tip.adapter.file.outbound.FileInteractionSpec
<2007-06-11 19:00:42,834> <DEBUG> <default.collaxa.cube.ws> <AdapterFramework::Outbound> Populating outbound JCA interactionSpec oracle.tip.adapter.file.outbound.FileInteractionSpec with properties: {FileNamingConvention=spob230_%SEQ%.txt, OpaqueSchema=true, ElapsedTime=60, NumberMessages=1, PhysicalDirectory=c:\inbound_dir, FileSize=1024000}
07/06/11 19:00:42 file:/D:/OraHome_1/integration/orabpel/domains/default/tmp/.bpel_FTPRetrieveTOFileWriteProcess_1.0.jar/fileAdapterOutboundHeader.wsdl
07/06/11 19:00:42 file:/D:/OraHome_1/integration/orabpel/domains/default/tmp/.bpel_FTPRetrieveTOFileWriteProcess_1.0.jar/fileAdapterOutboundHeader.wsdl
07/06/11 19:00:42 file:/D:/OraHome_1/integration/orabpel/domains/default/tmp/.bpel_FTPRetrieveTOFileWriteProcess_1.0.jar/Write.wsdl
<2007-06-11 19:00:42,849> <DEBUG> <default.collaxa.cube.ws> <AdapterFramework::Outbound> file:/D:/OraHome_1/integration/orabpel/domains/default/tmp/.bpel_FTPRetrieveTOFileWriteProcess_1.0.jar/Write.wsdl [ Write_ptt::Write(opaque) ] - Invoking JCA outbound Interaction
<2007-06-11 19:00:42,849> <INFO> <default.collaxa.cube.ws> <File Adapter::Outbound> File Adapter received an input Record
<2007-06-11 19:00:42,849> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> Waiting outside sync object.....
<2007-06-11 19:00:42,849> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> Batcher created using staging : true with number of messages : 1
<2007-06-11 19:00:42,849> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> Input Record: javax.xml.transform.dom.DOMSource@e5394c
<2007-06-11 19:00:42,849> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> Translating....
<2007-06-11 19:00:42,849> <INFO> <default.collaxa.cube.ws> <File Adapter::Outbound> Outbound Translation done.
<2007-06-11 19:00:42,865> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> Refreshed (staging/num Messages) file count : 1
<2007-06-11 19:00:42,865> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> Host DT1521-localhost.com FTP command: USER orabpel
<2007-06-11 19:00:42,865> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> Wrote to Control File
<2007-06-11 19:00:42,865> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> Batching staging File: staging0
<2007-06-11 19:00:42,865> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> Batcher sending to sender for output file writing
<2007-06-11 19:00:42,865> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> Sending File to output Dir
<2007-06-11 19:00:42,865> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> FileAgent.putFile() puts spob230_17.txt in c:\inbound_dir begins ...
<2007-06-11 19:00:42,865> <INFO> <default.collaxa.cube.ws> <File Adapter::Outbound> Done Writing to output file spob230_17.txt in dir c:\inbound_dir !!
<2007-06-11 19:00:42,881> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> End clearing Control File
<2007-06-11 19:00:42,881> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> Deleting staging File: staging0
<2007-06-11 19:00:42,881> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> End clearing Control File
<2007-06-11 19:00:42,881> <INFO> <default.collaxa.cube.ws> <File Adapter::Outbound> Interaction gets a ok response
<2007-06-11 19:00:42,881> <INFO> <default.collaxa.cube.ws> <File Adapter::Outbound> Done with Input Record
<2007-06-11 19:00:43,256> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> FTP Command: USER, reply:
331 Password required for orabpel
<2007-06-11 19:00:43,256> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> Host DT1521-localhost.com FTP command: PASS
<2007-06-11 19:00:43,506> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> FTP Command: PASS, reply:
230 Login OK
<2007-06-11 19:00:43,506> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> Host DT1521-localhost.com FTP command: CWD /click/xelusparts/feeds/jabilparts/outbound/process/
<2007-06-11 19:00:43,615> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> FTP Command: CWD, reply:
250 Directory successfully changed
<2007-06-11 19:00:43,615> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> Host DT1521-localhost.com FTP command: DELE po_28.txt
<2007-06-11 19:00:43,709> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> FTP Command: DELE, reply:
200 Deleted file "po_28.txt".
<2007-06-11 19:00:43,709> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> FTPClient.deleteFile(): 200 Deleted file "po_28.txt".
<2007-06-11 19:00:43,709> <ERROR> <default.collaxa.cube.ws> <File Adapter::Outbound> FTPClient.deleteFile(): Unable to delete file po_28.txt', reply code = 200
<2007-06-11 19:00:43,709> <DEBUG> <default.collaxa.cube.ws> <File Adapter::Outbound> Processer thread calling onFatalError with exception Error deleting file from FTP Server.
Unable to delete file from server.
Please ensure whether the remote file has delete permission.
<2007-06-11 19:00:43,709> <FATAL> <default.collaxa.cube.activation> <AdapterFramework::Inbound> [Get_ptt::Get(opaque)] - Resource Adapter requested Process shutdown!
<2007-06-11 19:00:43,709> <INFO> <default.collaxa.cube.activation> <AdapterFramework::Inbound> Adapter Framework instance: OraBPEL - performing endpointDeactivation for portType=Get_ptt, operation=Get
<2007-06-11 19:00:43,709> <INFO> <default.collaxa.cube.ws> <File Adapter::Outbound> Endpoint De-activation called in adapter for endpoint : /click/xelusparts/feeds/jabilparts/outbound/process/
<2007-06-11 19:00:43,725> <DEBUG> <default.collaxa.cube.engine.deployment> <CubeProcessHolder::loadAndBind> Check if process FTPRetrieveTOFileWriteProcess, revision 1.0 needs to be reloaded
<2007-06-11 19:00:44,037> <INFO> <default.collaxa.cube.activation> <AdapterFramework::Inbound> JCAActivationAgent::onStateChanged State is changed for process 'bpel://localhost/default/FTPRetrieveTOFileWriteProcess~1.0/', state=OFF
<2007-06-11 19:00:44,037> <DEBUG> <default.collaxa.cube.engine.deployment> <CubeProcessHolder::updateRevision> Updated state for process FTPRetrieveTOFileWriteProcess (revision 1.0) to 1
Thanks,
Vidya

Hi SR,
You can do this by having a BPEL process with a java embedding containing below code.
* Input Variables
String processName = (String)getVariableData("processName");
String revision = (String)getVariableData("revision");
* Declare variables.
IBPELProcessHandle procHandle = null;
Locator loc = null;
BPELProcessMetaData bpelProcessMetadata = null;
try{
 * get Locator Instance
 loc = getLocator();
 * Lookup Process. Revision optional.
 if(revision == null || revision.trim().equals(""))
 procHandle = loc.lookupProcess( processName );
 else
 procHandle = loc.lookupProcess(processName, revision);
 if(procHandle == null)
 throw new Exception("Unable to find process: " + processName);
 * Get Metadata of the process.
 bpelProcessMetadata = procHandle.getMetaData();
 * Set Lifecycle to Retired.
 * Use setState(IBPELProcessConstants.STATE_OFF) to change process state to off.
 bpelProcessMetadata.setLifecycle(IBPELProcessConstants.LIFECYCLE_RETIRED);
 * Finally update the process with the modified metadata.
 procHandle.updateMetaData(bpelProcessMetadata);
}catch (Exception e)
addAuditTrailEntry(e);
}If you want you can schedule this process.
Regards
PavanKumar.M

Virtual machine state : Paused-Critical

Hello,
I'm testing Hyper-V and three virtual machines (512MB of allocated memory) on 2GB of physical memory.
It has run during some hours but suddently, all VM switched to "paused-critical" state. What's the reason? Is it a problem of memory? I know I'm pushing the computer limits but when I turned off one of the VM, I was able to start the others. The machines have run during few seconds and switched again to the "paused-critical" status.
Chris

In my case it is the Core Server - Hyper-V partition which ran out of space. I thought I was being generous with a 40GB partition for what was supposed to be a very light footprint OS option. I'll have to get a closer look, because that just doesn't seem right.
Thanks for specifying what that 'State' information indicates. This information is NOT available via the Hyper-V Manager Help section using either "Paused-Critical" or "State" as search terms. It would be greatly helpful to add that to the Help section.

Yoga 11 Secure Boot State Off - How to enable it?

Hi all, first of all I would like to provide you with some background information. I purchased (in Germany) 2 identical Yoga 11 machines (MAS29GE). Both had display ghosting issues and one of them had a lose trackpad. So, I sent them in for repair.
After getting back the 2nd one as well, I wanted to see whether the BIOS versions are identical on them, since the repair report said that there was a BIOS update performed on both machines. The BIOS version seems to be the very same I had before sending them in: v1.2.58, 05.12.2012
But then I noticed something strange: on one of the Yogas the Secure Boot State is Off. I checked it also with PowerShell and it shows False, meaning disabled.
So, I called Lenovo support, but they weren't able to help me. The answer was that I cannot enter the BIOS to change this.
However, I suspect that either the technicians entered the BIOS and forgot to enable secure boot later on, or something else messed it up. What I also noticed after receiving the Yogas back from repair is that the "Advanced Startup" in
Windows shows more options on one machne than the other. Please, see the below images for details:
Link to picture
Link to picture
I did 2x System restores already (1x quick, 1x secure), but the Secure Boot State did not change (this was to be expected since this settings is in the UEFI BIOS and not in Windows - nevertheless, was worth a try).
As I read in other comments, Microsoft did not intend users to enter the BIOS on Windows RT machines.
Please, note that I did not "Jailbreak" the system, for 1) I have no idea how to do it and 2) I don't intend to hack it. One reason why I bought Windows RT because I wanted to keep legacy x86 viruses out of the system.
So, what do you suggest? I really do not wish to send the machine back for another 2 weeks only for 1 single change in the BIOS. Please, help! Thanks!
Moderator note; picture(s) totalling >50K converted to link(s) Forum Rules
Solved!
Go to Solution.

Hello,
As far as I know, you are the only individual I have ever heard of who has received a Windows RT-based computer with the Secure Boot option disabled.
Because of this, I am not certain what steps you would take to (re)enable this functionality on the device.
What I would suggest you do is perhaps post a message on the Windows 8, RT Development and Hacking forum over at XDA-Developers, and perhaps one of the members over there can make some suggestions.
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

Agent in critical state / Performance critical

Hi!
I have a server that looks like this:
What can be wrong?
The enviroment is scom 2012 R2.
The server has no issues with performance what I can see.

Hi,
What if you put the server in Maintenace Mode for 15 min. ?
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.
Thank you! It shows Healthy after that! Weird ;)..

SAP work Process goes in run state,Users cannot login developer trace paste

Hi team,
We have a system which is at ECC6 release 701 ABAP + java system.
The work process frequently go in run state and since this is an IDES system, I always restart the system.
Please help me since i want tio know the root cause for the same.
The dev trace is as follows, and i beleive its a listener problem by the logs.
kernel runs with dp version 244000(ext=110000) (@(#) DPLIB-INT-VERSION-244000-UC)
length of sys_adm_ext is 576 bytes
SWITCH TRC-HIDE on ***
***LOG Q00=> DpSapEnvInit, DPStart (00 199004) [dpxxdisp.c 1287]
 shared lib "dw_xml.dll" version 254 successfully loaded
 shared lib "dw_xtc.dll" version 254 successfully loaded
 shared lib "dw_stl.dll" version 254 successfully loaded
 shared lib "dw_gui.dll" version 254 successfully loaded
 shared lib "dw_mdm.dll" version 254 successfully loaded
rdisp/softcancel_sequence : -> 0,5,-1
use internal message server connection to port 3900
Mon Dec 13 08:26:23 2010
WARNING => DpNetCheck: NiHostToAddr(www.doesnotexist0223.qqq.nxst) took 6 seconds
<EsNT> Using memory model view.
<EsNT> Memory Reset disabled as NT default
<ES> 127 blocks reserved for free list.
ES initialized.
mm.dump: set maximum dump mem to 96 MB
Mon Dec 13 08:26:29 2010
J2EE server info
start = TRUE
state = STARTED
pid = 200040
argv[0] = D:\usr\sap\BI7\DVEBMGS00\exe\jcontrol.EXE
argv[1] = D:\usr\sap\BI7\DVEBMGS00\exe\jcontrol.EXE
argv[2] = pf=D:\usr\sap\BI7\SYS\profile\BI7_DVEBMGS00_q4de3gsy203
argv[3] = -DSAPSTART=1
argv[4] = -DCONNECT_PORT=65000
argv[5] = -DSAPSYSTEM=00
argv[6] = -DSAPSYSTEMNAME=BI7
argv[7] = -DSAPMYNAME=q4de3gsy203_BI7_00
argv[8] = -DSAPPROFILE=D:\usr\sap\BI7\SYS\profile\BI7_DVEBMGS00_q4de3gsy203
argv[9] = -DFRFC_FALLBACK=ON
argv[10] = -DFRFC_FALLBACK_HOST=localhost
start_lazy = 0
start_control = SAP J2EE startup framework
DpJ2eeStart: j2ee state = STARTED
rdisp/http_min_wait_dia_wp : 1 -> 1
***LOG CPS=> DpLoopInit, ICU ( 3.0 3.0 4.0.1) [dpxxdisp.c 1694]
***LOG Q0K=> DpMsAttach, mscon ( q4de3gsy203) [dpxxdisp.c 12697]
DpStartStopMsg: send start message (myname is >q4de3gsy203_BI7_00 <)
DpStartStopMsg: start msg sent
CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
CCMS: start to initalize 3.X shared alert area (first segment).
DpMsgAdmin: Set release to 7000, patchlevel 0
MBUF state PREPARED
MBUF component UP
DpMBufHwIdSet: set Hardware-ID
***LOG Q1C=> DpMBufHwIdSet [dpxxmbuf.c 1050]
DpMsgAdmin: Set patchno for this platform to 254
Release check o.K.
DpJ2eeLogin: j2ee state = CONNECTED
Mon Dec 13 08:27:09 2010
my types changed after wp death/restart 0xbf --> 0xbd
my types changed after wp death/restart 0xbd --> 0xb5
my types changed after wp death/restart 0xb5 --> 0x95
Mon Dec 13 08:27:29 2010
ERROR => DpWPCheck: W1 (pid 199044) died (severity=0, status=0) [dpxxdisp.c 15841]
ERROR => DpWPCheck: W4 (pid 199912) died (severity=0, status=0) [dpxxdisp.c 15841]
ERROR => DpWPCheck: W6 (pid 192420) died (severity=0, status=0) [dpxxdisp.c 15841]
ERROR => DpWPCheck: W8 (pid 199528) died (severity=0, status=0) [dpxxdisp.c 15841]
ERROR => DpWPCheck: W9 (pid 198860) died (severity=0, status=0) [dpxxdisp.c 15841]
ERROR => DpWPCheck: W10 (pid 199664) died (severity=0, status=0) [dpxxdisp.c 15841]
my types changed after wp death/restart 0x95 --> 0x85
ERROR => DpWPCheck: W12 (pid 200036) died (severity=0, status=0) [dpxxdisp.c 15841]
Mon Dec 13 08:27:43 2010
***LOG Q0I=> NiIRead: recv (10054: WSAECONNRESET: Connection reset by peer) [nixxi.cpp 4424]
ERROR => NiIRead: SiRecv failed for hdl 6 / sock 316
 (SI_ECONN_BROKEN/10054; I4; ST; 127.0.0.1:4882) [nixxi.cpp 4424]
ERROR => DpJ2eeMsgProcess: NiRead failed (NIECONN_BROKEN) [dpxxj2ee.c 1212]
DpJ2eeMsgProcess: j2ee state = CONNECTED (NIECONN_BROKEN)
Mon Dec 13 08:27:49 2010
ERROR => DpWPCheck: W0 (pid 200632) died (severity=0, status=0) [dpxxdisp.c 15841]
ERROR => DpWPCheck: W1 (pid 199044) died (severity=0, status=0) [dpxxdisp.c 15841]
my types changed after wp death/restart 0x85 --> 0x84
ERROR => DpWPCheck: W3 (pid 93796) died (severity=0, status=0) [dpxxdisp.c 15841]
ERROR => DpWPCheck: W4 (pid 199912) died (severity=0, status=0) [dpxxdisp.c 15841]
ERROR => DpWPCheck: W5 (pid 200484) died (severity=0, status=0) [dpxxdisp.c 15841]
ERROR => DpWPCheck: W6 (pid 192420) died (severity=0, status=0) [dpxxdisp.c 15841]
my types changed after wp death/restart 0x84 --> 0x80
ERROR => DpWPCheck: W8 (pid 199528) died (severity=0, status=0) [dpxxdisp.c 15841]
ERROR => DpWPCheck: W9 (pid 198860) died (severity=0, status=0) [dpxxdisp.c 15841]
ERROR => DpWPCheck: W10 (pid 199664) died (severity=0, status=0) [dpxxdisp.c 15841]
ERROR => DpWPCheck: W11 (pid 199720) died (severity=0, status=0) [dpxxdisp.c 15841]
ERROR => DpWPCheck: W12 (pid 200036) died (severity=0, status=0) [dpxxdisp.c 15841]
DP_FATAL_ERROR => DpWPCheck: no more work processes
DISPATCHER EMERGENCY SHUTDOWN ***
increase tracelevel of WPs
NiWait: sleep (10000ms) ...
NiISelect: timeout 10000ms
NiISelect: maximum fd=493
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Mon Dec 13 08:27:59 2010
NiISelect: TIMEOUT occured (10000ms)
dump system status
Workprocess Table (long) Mon Dec 13 07:27:59 2010
========================
No Ty. Pid Status Cause Start Err Sem CPU Time Program Cl User Action Table
0 DIA 200632 Ended no 2 0 0
1 DIA 199044 Ended no 3 0 0
2 DIA 200280 Ended no 1 0 0
3 DIA 93796 Ended no 2 0 0
4 DIA 199912 Ended no 3 0 0
5 DIA 200484 Ended no 2 0 0
6 UPD 192420 Ended no 3 0 0
7 ENQ 199792 Ended no 1 0 0
8 BTC 199528 Ended no 3 0 0
9 BTC 198860 Ended no 3 0 0
10 BTC 199664 Ended no 3 0 0
11 SPO 199720 Ended no 2 0 0
12 UP2 200036 Ended no 3 0 0
Dispatcher Queue Statistics Mon Dec 13 07:27:59 2010
Switch off Shared memory profiling
ShmProtect( 57, 3 )
ShmProtect(SHM_PROFILE, SHM_PROT_RW
ShmProtect( 57, 1 )
ShmProtect(SHM_PROFILE, SHM_PROT_RD
DpWakeUpWps: wake up all wp's
Stop work processes
Stop gateway
killing process (184860) (SOFT_KILL)
Stop icman
killing process (190124) (SOFT_KILL)
Terminate gui connections
wait for end of work processes
wait for end of gateway
[DpProcDied] Process lives (PID:184860 HANDLE:440)
waiting for termination of gateway ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=493
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Mon Dec 13 08:28:05 2010
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process died (PID:184860 HANDLE:440)
wait for end of icman
[DpProcDied] Process lives (PID:190124 HANDLE:448)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=493
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Mon Dec 13 08:28:06 2010
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:190124 HANDLE:448)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=493
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Mon Dec 13 08:28:07 2010
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:190124 HANDLE:448)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=493
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Mon Dec 13 08:28:08 2010
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:190124 HANDLE:448)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=493
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Mon Dec 13 08:28:09 2010
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process died (PID:190124 HANDLE:448)
[DpProcDied] Process died (PID:200040 HANDLE:424)
DpStartStopMsg: send stop message (myname is >q4de3gsy203_BI7_00 <)
AdGetSelfIdentRecord: > <
AdCvtRecToExt: opcode 60 (AD_SELFIDENT), ser 0, ex 0, errno 0
AdCvtRecToExt: opcode 4 (AD_STARTSTOP), ser 0, ex 0, errno 0
DpConvertRequest: net size = 189 bytes
NiBufSend starting
NiIWrite: hdl 3 sent data (wrt=562,pac=1,MESG_IO)
MsINiWrite: sent 562 bytes
send msg (len 110+452) to name -, type 4, key -
DpStartStopMsg: stop msg sent
NiIRead: hdl 3 received data (rcd=274,pac=1,MESG_IO)
server
NiIRead: hdl 3 recv would block (errno=EAGAIN)
NiIRead: read for hdl 3 timed out (0ms)
DpHalt: no more messages from the message server
DpHalt: send keepalive to synchronize with the message server
NiBufReceive starting
MsINiRead: received 114 bytes
MSG received, len 110+4, flag 3, from MSG_SERVER , typ 0, key -
Received 4 bytes from MSG_SERVER
Received opcode MS_NOOP from msg_server, reply MSOP_OK
MsOpReceive: ok
MsSendKeepalive : keepalive sent to message server
NiIRead: hdl 3 recv would block (errno=EAGAIN)
Mon Dec 13 08:28:10 2010
NiIPeek: peek for hdl 3 timed out (r; 1000ms)
NiIRead: read for hdl 3 timed out (1000ms)
DpHalt: no more messages from the message server
DpHalt: sync with message server o.k.
detach from message server
***LOG Q0M=> DpMsDetach, ms_detach () [dpxxdisp.c 13043]
NiBufSend starting
NiIWrite: hdl 3 sent data (wrt=110,pac=1,MESG_IO)
MsINiWrite: sent 110 bytes
MsIDetach: send logout to msg_server
MsIDetach: call exit function
DpMsShutdownHook called
NiBufISelUpdate: new MODE -- (r-) for hdl 3 in set0
SiSelNSet: set events of sock 368 to: ---
NiBufISelRemove: remove hdl 3 from set0
SiSelNRemove: removed sock 368 (pos=3)
SiSelNRemove: removed sock 368
NiSelIRemove: removed hdl 3
MBUF state OFF
AdGetSelfIdentRecord: > <
AdCvtRecToExt: opcode 60 (AD_SELFIDENT), ser 0, ex 0, errno 0
AdCvtRecToExt: opcode 40 (AD_MSBUF), ser 0, ex 0, errno 0
AdCvtRecToExt: opcode 40 (AD_MSBUF), ser 0, ex 0, errno 0
blks_in_queue/wp_ca_blk_no/wp_max_no = 1/300/13
LOCK WP ca_blk 1
make DISP owner of wp_ca_blk 1
DpSemRq: key: 2, units: 1, timeout: -1
DpSemRel: key: 2, units: 1
DpRqPutIntoQueue: put request into queue (reqtype 1, prio LOW, rq_id 15)
MBUF component DOWN
NiICloseHandle: shutdown and close hdl 3 / sock 368
NiBufIClose: clear extension for hdl 3
MsIDetach: detach MS-system
cleanup EM
EsCleanup ....
EmCleanup() -> 0
Es2Cleanup: Cleanup ES2
***LOG Q05=> DpHalt, DPStop ( 199004) [dpxxdisp.c 11230]
Good Bye .....
Please revert if you need more information.
Regards,
Prasad Shetty

HI Juan,
trace file for dev_w0 as asked
C Starting user session: OCISessionBegin(con_hdl=0, usr=SAPSR3/<pwd>, svchp=0000000013FB7748, srvhp=0000000013FB9B78, usrhp=0000000013EA1EC8)
C Now 'SAPSR3/<pwd>@BI7' is connected: con_hdl=0, nls_hdl=0, session_id=65.
C Database NLS settings: AMERICAN_AMERICA.UTF8
C DB instance BI7 is running on Q4DE3GSY203 with ORACLE version 10.2.0.2.0 since DEC 13, 2010, 08:38:55
B Connection 0 opened (DBSL handle 0)
B Wp Hdl ConName ConId ConState TX HC PRM RCT FRC TIM MAX OPT Date Time DBHost
B 000 000 R/3 000000000 ACTIVE NO NO YES NO NO 000 255 255 20101213 083926 Q4DE3GSY203
C build_stmt: reallocating stmt buffer: 256 -> 2000 characters
M db_connect o.k.
M ICT: exclude compression: .zip,.cs,.rar,.arj,.z,.gz,.tar,.lzh,.cab,.hqx,.ace,.jar,.ear,.war,.css,.pdf,.js,.gzip,.uue,.bz2,.iso,.sda,.sar,.gif,*.png
I
I Mon Dec 13 08:40:14 2010
I MtxInit: 0 0 0
M SHM_PRES_BUF (addr: 0000000015860050, size: 4400000)
M SHM_ROLL_AREA (addr: 000007FFEA010050, size: 61440000)
M SHM_PAGING_AREA (addr: 0000000015CA0050, size: 32768000)
M SHM_ROLL_ADM (addr: 0000000017BF0050, size: 633840)
M SHM_PAGING_ADM (addr: 0000000017C90050, size: 525344)
M ThCreateNoBuffer allocated 544152 bytes for 1000 entries at 0000000017D20050
M ThCreateNoBuffer index size: 3000 elems
M ThCreateVBAdm allocated 12176 bytes (50 server) at 000000000B490050
X EmInit: MmSetImplementation( 2 ).
X MM global diagnostic options set: 0
X <ES> client 0 initializing ....
X Using implementation view
X ES initialized.
X mm.dump: set maximum dump mem to 96 MB
M Deactivate statistics hyper index locking
B dbntab: NTAB buffers attached
B dbntab: Buffer FTAB(hash header) (addr: 0000000017E400E0, size: 584)
B dbntab: Buffer FTAB(anchor array) (addr: 0000000017E40330, size: 320072)
B dbntab: Buffer FTAB(item array) (addr: 0000000017E8E580, size: 1280000)
B dbntab: Buffer FTAB(data area) (addr: 0000000017FC6D80, size: 30720000)
B dbntab: Buffer IREC(hash header) (addr: 0000000019D200E0, size: 584)
B dbntab: Buffer IREC(anchor array) (addr: 0000000019D20330, size: 320072)
B dbntab: Buffer IREC(item array) (addr: 0000000019D6E580, size: 320000)
B dbntab: Buffer IREC(data area) (addr: 0000000019DBC780, size: 6144000)
B dbntab: Buffer STAB(hash header) (addr: 000000001A3A00E0, size: 584)
B dbntab: Buffer STAB(anchor array) (addr: 000000001A3A0330, size: 320072)
B dbntab: Buffer STAB(item array) (addr: 000000001A3EE580, size: 320000)
B dbntab: Buffer STAB(data area) (addr: 000000001A43C780, size: 3072000)
B dbntab: Buffer TTAB(hash header) (addr: 000000001A7300E0, size: 1944)
B dbntab: Buffer TTAB(anchor array) (addr: 000000001A730880, size: 320072)
B dbntab: Buffer TTAB(item array) (addr: 000000001A77EAD0, size: 800000)
B dbntab: Buffer TTAB(data area) (addr: 000000001A841FD0, size: 5840000)
B db_con_shm_ini: WP_ID = 0, WP_CNT = 13, CON_ID = -1
B dbstat: TABSTAT buffer attached (addr: 000000001ADE9FB0)
B dbtbxbuf: Buffer TABL (addr: 000000001D7D0160, size: 30000000, end: 000000001F46C4E0)
B dbtbxbuf: Buffer TABLP (addr: 000000001F470160, size: 10240000, end: 000000001FE34160)
B dbexpbuf: Buffer EIBUF (addr: 000000001FE40170, size: 4194304, end: 0000000020240170)
B dbexpbuf: Buffer ESM (addr: 0000000020250170, size: 4194304, end: 0000000020650170)
B dbexpbuf: Buffer CUA (addr: 0000000020660170, size: 3072000, end: 000000002094E170)
B dbexpbuf: Buffer OTR (addr: 0000000020950170, size: 4194304, end: 0000000020D50170)
B dbcalbuf: Buffer CALE (addr: 0000000020D60050, size: 500000, end: 0000000020DDA170)
M CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
S *** init spool environment
S TSPEVJOB updates inside critical section: event_update_nocsec = 0
S initialize debug system
T Stack direction is downwards.
T debug control: prepare exclude for printer trace
T new memory block 00000000141756E0
S spool kernel/ddic check: Ok
S using table TSP02FX for frontend printing
S 1 spool work process(es) found
S frontend print via spool service enabled
S printer list size is 150
S printer type list size is 50
S queue size (profile) = 300
S hostspool list size = 3000
S option list size is 30
S intervals: query=50, rescan=1800, global=300 info=120
S processing queue enabled
S creating spool memory service RSPO-RCLOCKS at 000000002A0700D0
S doing lock recovery
S setting server cache root
S using server cache size 100 (prof=100)
S creating spool memory service RSPO-SERVERCACHE at 000000002A0704F0
S using messages for server info
B dbtran INFO (init_connection '<DEFAULT>' [ORACLE:700.08]):
B max_blocking_factor = 5, max_in_blocking_factor = 5,
B min_blocking_factor = 5, min_in_blocking_factor = 5,
B prefer_union_all = 0, prefer_join = 0,
B prefer_fix_blocking = 0, prefer_in_itab_opt = 1,
B convert AVG = 0, alias table FUPD = 0,
B escape_as_literal = 1, opt GE LE to BETWEEN = 0,
B select * =0x0f, character encoding = STD / <none>:-,
B use_hints = abap->1, dbif->0x1, upto->2147483647, rule_in->0,
B rule_fae->0, concat_fae->0, concat_fae_or->0
S
S Mon Dec 13 08:40:15 2010
S size of spec char cache entry: 297032 bytes (timeout 100 sec)
S size of open spool request entry: 2512 bytes
S immediate print option for implicitely closed spool requests is disabled
A **GENER Trace switched on ***
A
A -PXA--
A PXA INITIALIZATION
A PXA: Locked PXA-Semaphore.
A System page size: 4kb, total admin_size: 20564kb, dir_size: 20472kb.
A Attached to PXA (address 000007FFEDAB0050, size 300000K)
A abap/pxa = shared protect gen_remote
A PXA INITIALIZATION FINISHED
A -PXA--
A
A ABAP ShmAdm attached (addr=000007FF4FEEA000 leng=20955136 end=000007FF512E6000)
A >> Shm MMADM area (addr=000007FF50392E80 leng=247168 end=000007FF503CF400)
A >> Shm MMDAT area (addr=000007FF503D0000 leng=15818752 end=000007FF512E6000)
A RFC Destination> destination q4de3gsy203_BI7_00 host q4de3gsy203 system BI7 systnr 0 (q4de3gsy203_BI7_00)
A RFC Options> H=q4de3gsy203,S=00,d=2,
A RFC FRFC> fallback activ but this is not a central instance.
A
A RFC rfc/signon_error_log = -1
A RFC rfc/dump_connection_info = 0
A RFC rfc/dump_client_info = 0
A RFC rfc/cp_convert/ignore_error = 1
A RFC rfc/cp_convert/conversion_char = 23
A RFC rfc/wan_compress/threshold = 251
A RFC rfc/recorder_pcs not set, use defaule value: 2
A RFC rfc/delta_trc_level not set, use default value: 0
A RFC rfc/no_uuid_check not set, use default value: 0
A RFC rfc/bc_ignore_thcmaccp_retcode not set, use default value: 0
A RFC Method> initialize RemObjDriver for ABAP Objects
M ThrCreateShObjects allocated 27042 bytes at 000000002A9E0050
N
N Mon Dec 13 08:40:16 2010
N SsfSapSecin: putenv(SECUDIR=D:\usr\sap\BI7\DVEBMGS00\sec): ok
N
N =================================================
N === SSF INITIALIZATION:
N ===...SSF Security Toolkit name SAPSECULIB .
N ===...SSF trace level is 0 .
N ===...SSF library is D:\usr\sap\BI7\DVEBMGS00\exe\sapsecu.dll .
N ===...SSF hash algorithm is SHA1 .
N ===...SSF symmetric encryption algorithm is DES-CBC .
N ===...sucessfully completed.
N =================================================
N
N Mon Dec 13 08:40:17 2010
N MskiInitLogonTicketCacheHandle: Logon Ticket cache pointer retrieved from shared memory.
N MskiInitLogonTicketCacheHandle: Workprocess runs with Logon Ticket cache.
M JrfcVmcRegisterNativesDriver o.k.
W =================================================
W === ipl_Init() called
W ITS Plugin: Path dw_gui
W ITS Plugin: Description ITS Plugin - ITS rendering DLL
W ITS Plugin: sizeof(SAP_UC) 2
W ITS Plugin: Release: 700, [7000.0.254.20050900]
W ITS Plugin: Int.version, [33]
W ITS Plugin: Feature set: [22]
W ===... Calling itsp_Init in external dll ===>
W === ipl_Init() returns 0, ITSPE_OK: OK
W =================================================
N VSI: WP init in ABAP VM completed with rc=0
E Profile-Parameter: enque/deque_wait_answer = FALSE
E Profile-Parameter: enque/sync_dequeall = 0
E Replication is disabled
E EnqCcInitialize: local lock table initialization o.k.
E EnqId_SuppressIpc: local EnqId initialization o.k.
E EnqCcInitialize: local enqueue client init o.k.
S
S Mon Dec 13 08:40:19 2010
S found spool memory service RSPO-ACTIONS at 000000002A07A230
A
A Mon Dec 13 08:40:20 2010
A **GENER Trace switched off ***
M SosICreateNewAnchorArray: sos_search_anchor_semantics = 1
C
C Mon Dec 13 08:40:21 2010
C build_stmt: reallocating stmt buffer: 2000 -> 3002 characters
B table logging switched on for client '800'
M
M Mon Dec 13 08:40:23 2010
M SecAudit(RsauShmInit): WP attached to existing shared memory.
M SecAudit(RsauShmInit): addr of SCSA........... = 000000000AFC0050
M SecAudit(RsauShmInit): addr of RSAUSHM........ = 000000000AFC07C0
M SecAudit(RsauShmInit): addr of RSAUSLOTINFO... = 000000000AFC0800
M SecAudit(RsauShmInit): addr of RSAUSLOTS...... = 000000000AFC080C
M rdisp/rb_cleaned_rfc = 0
M
M Mon Dec 13 08:40:27 2010
M Deactivate ASTAT hyper index locking
M
M Mon Dec 13 08:44:30 2010
M
M *****************************************************************************
M *
M * LOCATION SAP-Gateway on host q4de3gsy203 / sapgw00
M * ERROR program dbmrfc@sapdb not registered
M *
M * TIME Mon Dec 13 08:44:30 2010
M * RELEASE 700
M * COMPONENT SAP-Gateway
M * VERSION 2
M * RC 679
M * MODULE gwr3cpic.c
M * LINE 1835
M * DETAIL TP dbmrfc@sapdb not registered
M * COUNTER 15
M *
M *****************************************************************************
M
A RFC 1485 CONVID 21905907
A * CMRC=2 DATA=0 STATUS=0 SAPRC=679 ThSAPOCMINIT
A RFC> ABAP Programm: SAPLSADC (Transaction: )
A RFC> User: RANGUPTA (Client: 001)
A RFC> Destination: SAPDB_DBM_DAEMON (handle: 2, , )
A RFC SERVER> RFC Server Session (handle: 1, 21904860, {D18C06E0-7859-F141-92A8-005056956B4B})
A RFC SERVER> Caller host:
A RFC SERVER> Caller transaction code: (Caller Program: SAPLSADC)
A RFC SERVER> Called function module: DBM_CONNECT_PUR
A TH VERBOSE LEVEL FULL
A ** RABAX: end RX_GET_MESSAGE
M
M Mon Dec 13 08:45:54 2010
M
M *****************************************************************************
M *
M * LOCATION SAP-Gateway on host q4de3gsy203 / sapgw00
M * ERROR program dbmrfc@sapdb not registered
M *
M * TIME Mon Dec 13 08:45:54 2010
M * RELEASE 700
M * COMPONENT SAP-Gateway
M * VERSION 2
M * RC 679
M * MODULE gwr3cpic.c
M * LINE 1835
M * DETAIL TP dbmrfc@sapdb not registered
M * COUNTER 30
M *
M *****************************************************************************
M
A RFC 1485 CONVID 21998657
A * CMRC=2 DATA=0 STATUS=0 SAPRC=679 ThSAPOCMINIT
A RFC> ABAP Programm: SAPLSADC (Transaction: )
A RFC> User: RANGUPTA (Client: 001)
A RFC> Destination: SAPDB_DBM_DAEMON (handle: 2, , )
A RFC SERVER> RFC Server Session (handle: 1, 21997642, {038D06E0-8E49-F147-92A8-005056956B4B})
A RFC SERVER> Caller host:
A RFC SERVER> Caller transaction code: (Caller Program: SAPLSADC)
A RFC SERVER> Called function module: DBM_CONNECT_PUR
A TH VERBOSE LEVEL FULL
A ** RABAX: end RX_GET_MESSAGE
M
M Mon Dec 13 08:48:12 2010
M
M *****************************************************************************
M *
M * LOCATION SAP-Gateway on host q4de3gsy203 / sapgw00
M * ERROR program dbmrfc@sapdb not registered
M *
M * TIME Mon Dec 13 08:48:12 2010
M * RELEASE 700
M * COMPONENT SAP-Gateway
M * VERSION 2
M * RC 679
M * MODULE gwr3cpic.c
M * LINE 1835
M * DETAIL TP dbmrfc@sapdb not registered
M * COUNTER 45
M *
M *****************************************************************************
M
A RFC 1485 CONVID 22146986
A * CMRC=2 DATA=0 STATUS=0 SAPRC=679 ThSAPOCMINIT
A RFC> ABAP Programm: SAPLSADC (Transaction: )
A RFC> User: RANGUPTA (Client: 001)
A RFC> Destination: SAPDB_DBM_DAEMON (handle: 2, , )
A RFC SERVER> RFC Server Session (handle: 1, 22145986, {558D06E0-45BF-F199-92A8-005056956B4B})
A RFC SERVER> Caller host:
A RFC SERVER> Caller transaction code: (Caller Program: SAPLSADC)
A RFC SERVER> Called function module: DBM_CONNECT_PUR
A TH VERBOSE LEVEL FULL
A ** RABAX: end RX_GET_MESSAGE
M
M Mon Dec 13 08:49:33 2010
M
M *****************************************************************************
M *
M * LOCATION SAP-Gateway on host q4de3gsy203 / sapgw00
M * ERROR program dbmrfc@sapdb not registered
M *
M * TIME Mon Dec 13 08:49:33 2010
M * RELEASE 700
M * COMPONENT SAP-Gateway
M * VERSION 2
M * RC 679
M * MODULE gwr3cpic.c
M * LINE 1835
M * DETAIL TP dbmrfc@sapdb not registered
M * COUNTER 60
M *
M *****************************************************************************
It is a bit large will this do ?
Regards,
Prasad

File Adapter Polling issue(Is there critical value of File size )?

Hi
I use File adapter as the Activation to initialize a BPEL process instance .The source data is a kind of Delimited file format.On my PC, when the file size is less than 4M ,everything works fine ,But when the size increased. The BPEL process will not initialize the instance.When the source data is XML data , the "critical value " is about 12M. The error msg is below.
<2005-08-08 12:48:26,209> <INFO> <default.collaxa.cube.activation> <File Adapter::Inbound> Processing file : D:\Temp\WOSSystemIntegration\InBoundFiles\LOADPLAN_DATA_200508041708.xml
<2005-08-08 12:48:29,455> <INFO> <default.collaxa.cube.activation> <FileAdapter::Inbound> Sending message to Adapter Framework for posting to BPEL engine: { file=D:\Temp\WOSSystemIntegration\InBoundFiles\LOADPLAN_DATA_200508041708.xml
<2005-08-08 12:48:40,197> <ERROR> <default.collaxa.cube> <BaseCubeSessionBean::l
ogError> Error while invoking bean "cube delivery": Delivery callback message se
rialization failed.
An attempt to serialize the delivery callback messages for conversation "LocalGU
ID:d0b7ccf8e4242850:134b07e:10594606738:-7ffc", message "d0b7ccf8e4242850:134b07
e:10594606738:-7ffb" to binary format has failed. The exception reported is:
<2005-08-08 12:48:40,245> <ERROR> <default.collaxa.cube> <BaseCubeSessionBean::l
ogError> Error while invoking bean "delivery": Delivery callback message seriali
zation failed.
An attempt to serialize the delivery callback messages for conversation "LocalGU
ID:d0b7ccf8e4242850:134b07e:10594606738:-7ffc", message "d0b7ccf8e4242850:134b07
e:10594606738:-7ffb" to binary format has failed. The exception reported is:
<2005-08-08 12:48:40,245> <ERROR> <default.collaxa.cube.activation> <AdapterFram
ework::Inbound> [Read_ptt::Read(loadPlanCollection)] - JCA Activation Agent was
unable to perform delivery of inbound message to BPEL Process 'bpel://localhost/
default/P2E_WOS_LP~1.0/' due to: Delivery callback message serialization failed.
An attempt to serialize the delivery callback messages for conversation "LocalGU
ID:d0b7ccf8e4242850:134b07e:10594606738:-7ffc", message "d0b7ccf8e4242850:134b07
e:10594606738:-7ffb" to binary format has failed. The exception reported is:
<2005-08-08 12:48:40,245> <ERROR> <default.collaxa.cube.activation> <AdapterFram
ework::Inbound>
com.oracle.bpel.client.ServerException: Delivery callback message serialization
failed.
An attempt to serialize the delivery callback messages for conversation "LocalGU
ID:d0b7ccf8e4242850:134b07e:10594606738:-7ffc", message "d0b7ccf8e4242850:134b07
e:10594606738:-7ffb" to binary format has failed. The exception reported is:
at com.collaxa.cube.engine.delivery.DeliveryHandler.initialPostAnyType(D
eliveryHandler.java:328)
at com.collaxa.cube.engine.delivery.DeliveryHandler.initialPost(Delivery
Handler.java:219)
at com.collaxa.cube.engine.delivery.DeliveryHandler.post(DeliveryHandler
.java:83)
at com.collaxa.cube.ejb.impl.DeliveryBean.post(DeliveryBean.java:181)
at IDeliveryBean_StatelessSessionBeanWrapper22.post(IDeliveryBean_Statel
essSessionBeanWrapper22.java:861)
at com.oracle.bpel.client.delivery.DeliveryService.post(DeliveryService.
java:161)
at oracle.tip.adapter.fw.AdapterFrameworkListenerBase$DeliveryServiceMon
itor.send(AdapterFrameworkListenerBase.java:2340)
at oracle.tip.adapter.fw.AdapterFrameworkListenerBase.executeDeliverySer
viceSend(AdapterFrameworkListenerBase.java:478)
at oracle.tip.adapter.fw.AdapterFrameworkListenerBase.deliveryServiceSen
d(AdapterFrameworkListenerBase.java:535)
at oracle.tip.adapter.fw.jca.AdapterFrameworkListenerImpl.performSingleA
ctivation(AdapterFrameworkListenerImpl.java:699)
at oracle.tip.adapter.fw.jca.AdapterFrameworkListenerImpl.onMessage(Adap
terFrameworkListenerImpl.java:567)
at oracle.tip.adapter.fw.jca.messageinflow.MessageEndpointImpl.onMessage
(MessageEndpointImpl.java:121)
at oracle.tip.adapter.file.inbound.ProcessWork.publishMessage(ProcessWor
k.java:651)
at oracle.tip.adapter.file.inbound.ProcessWork.doTranslation(ProcessWork
.java:456)
at oracle.tip.adapter.file.inbound.ProcessWork.processMessages(ProcessWo
rk.java:200)
at oracle.tip.adapter.file.inbound.ProcessWork.run(ProcessWork.java:139)
at oracle.tip.adapter.fw.jca.work.WorkerJob.go(WorkerJob.java:51)
at oracle.tip.adapter.fw.common.ThreadPool.run(ThreadPool.java:267)
at java.lang.Thread.run(Thread.java:534)
<2005-08-08 12:48:40,245> <INFO> <default.collaxa.cube.activation> <File Adapter
::Inbound> Failed to send message {D:\Temp\WOSSystemIntegration\InBoundFiles\LOA
DPLAN_DATA_200508041708.xml} to Adapter Framework.
<2005-08-08 12:48:40,245> <WARN> <default.collaxa.cube.activation> <AdapterFrame
work::Inbound> [Read_ptt::Read(loadPlanCollection)] - onReject: Sending invalid
inbound message to Exception Handler: file://D:/Temp/WOSSystemIntegration/Reject
edMessages
<2005-08-08 12:49:44,617> <FATAL> <default.collaxa.cube.activation> <AdapterFram
ework::Inbound> [Read_ptt::Read(loadPlanCollection)] - Resource Adapter requeste
d Process shutdown
<2005-08-08 12:49:48,676> <INFO> <default.collaxa.cube.activation> <AdapterFrame
work::Inbound> Adapter Framework instance: OraBPEL - performing endpointDeactiva
tion for portType=Read_ptt, operation=Read
<2005-08-08 12:49:48,676> <INFO> <default.collaxa.cube.activation> <File Adapter
::Inbound> Endpoint De-activation called in adapter for endpoint : D:\Temp\WOSSy
stemIntegration\InBoundFiles
<2005-08-08 12:49:49,042> <INFO> <default.collaxa.cube.activation> <AdapterFrame
work::Inbound> JCAActivationAgent::onStateChanged State is changed for process '
bpel://localhost/default/P2E_WOS_LP~1.0/', state=OFF
how can i solve this problem?can i predeploy some parameter? Is there some critical value of File size for the processing of File Adapter ?

Hi,
There is no specific parameters to specify the maximum file size to be read in. It is just limited by the heap size of the JVM running the BPEL engine.
If you have enough RAM on your machine you can change the current heap size from 512Mbyte to 1Go by editing the startorabpel.bat file
and modifying the line :
set MEM_ARGS=-Xms512m -Xmx512m -Xmn300m -XX:MaxPermSize=80m
to
set MEM_ARGS=-Xms512m -Xmx1024m -Xmn300m -XX:MaxPermSize=80m
But only do it if you have at least 1.5 Gb of RAM on your machine, otherwise ot will keep spawing and you will have very bad performance.
Speaking about performance, do you really need to have a BPEL payload of 4 to 12 Mb ?
Will the BPEL process really need to access it ? if so, the best solution would be using batching techniques to cut you file in pieces and process it piece by peice.
FB.

Dispatcher stopped and Workprocessors are Ended State

Hi Experts
Suddenly my dispatcher stopped and all work processors are in Ended state in the ECC6.0 with Oracle database in windows 2003. I have checked the Memory parameters and resetted the values but still getting the same problem here i am pasting the dev_disp and dev_w0 files. Please help me need full
Regards
Chandra
dev_disp::
trc file: "dev_disp", trc level: 1, release: "700"
sysno 00
sid CHE
systemid 560 (PC with Windows NT)
relno 7000
patchlevel 0
patchno 175
intno 20050900
make: multithreaded, Unicode, optimized
pid 1536
Sun Dec 07 13:05:43 2008
kernel runs with dp version 241000(ext=110000) (@(#) DPLIB-INT-VERSION-241000-UC)
length of sys_adm_ext is 576 bytes
SWITCH TRC-HIDE on ***
***LOG Q00=> DpSapEnvInit, DPStart (00 1536) [dpxxdisp.c 1261]
 shared lib "dw_xml.dll" version 175 successfully loaded
 shared lib "dw_xtc.dll" version 175 successfully loaded
 shared lib "dw_stl.dll" version 175 successfully loaded
 shared lib "dw_gui.dll" version 175 successfully loaded
 shared lib "dw_mdm.dll" version 175 successfully loaded
rdisp/softcancel_sequence : -> 0,5,-1
use internal message server connection to port 3900
Sun Dec 07 13:05:54 2008
WARNING => DpNetCheck: NiHostToAddr(www.doesnotexist0081.qqq.nxst) took 11 seconds
Sun Dec 07 13:05:59 2008
WARNING => DpNetCheck: NiAddrToHost(1.0.0.0) took 5 seconds
***LOG GZZ=> 2 possible network problems detected - check tracefile and adjust the DNS settings [dpxxtool2.c 5418]
MtxInit: 30000 0 0
DpSysAdmExtInit: ABAP is active
DpSysAdmExtInit: VMC (JAVA VM in WP) is not active
DpIPCInit2: start server >I3LSERVSAP1_CHE_00 <
DpShMCreate: sizeof(wp_adm) 23856 (1704)
DpShMCreate: sizeof(tm_adm) 4415616 (21968)
DpShMCreate: sizeof(wp_ca_adm) 24064 (80)
DpShMCreate: sizeof(appc_ca_adm) 8000 (80)
DpCommTableSize: max/headSize/ftSize/tableSize=500/8/528056/528064
DpShMCreate: sizeof(comm_adm) 528064 (1048)
DpSlockTableSize: max/headSize/ftSize/fiSize/tableSize=0/0/0/0/0
DpShMCreate: sizeof(slock_adm) 0 (96)
DpFileTableSize: max/headSize/ftSize/tableSize=0/0/0/0
DpShMCreate: sizeof(file_adm) 0 (72)
DpShMCreate: sizeof(vmc_adm) 0 (1544)
DpShMCreate: sizeof(wall_adm) (38456/34360/64/184)
DpShMCreate: sizeof(gw_adm) 48
DpShMCreate: SHM_DP_ADM_KEY (addr: 06840040, size: 5081056)
DpShMCreate: allocated sys_adm at 06840040
DpShMCreate: allocated wp_adm at 06842118
DpShMCreate: allocated tm_adm_list at 06847E48
DpShMCreate: allocated tm_adm at 06847E78
DpShMCreate: allocated wp_ca_adm at 06C7DEF8
DpShMCreate: allocated appc_ca_adm at 06C83CF8
DpShMCreate: allocated comm_adm at 06C85C38
DpShMCreate: system runs without slock table
DpShMCreate: system runs without file table
DpShMCreate: allocated vmc_adm_list at 06D06AF8
DpShMCreate: allocated gw_adm at 06D06B38
DpShMCreate: system runs without vmc_adm
DpShMCreate: allocated ca_info at 06D06B68
DpShMCreate: allocated wall_adm at 06D06B70
MBUF state OFF
DpCommInitTable: init table for 500 entries
rdisp/queue_size_check_value : -> off
ThTaskStatus: rdisp/reset_online_during_debug 0
EmInit: MmSetImplementation( 2 ).
MM global diagnostic options set: 0
<ES> client 0 initializing ....
<ES> InitFreeList
<ES> block size is 1024 kByte.
Using implementation view
<EsNT> Using memory model view.
<EsNT> Memory Reset disabled as NT default
<ES> 4075 blocks reserved for free list.
ES initialized.
rdisp/http_min_wait_dia_wp : 1 -> 1
***LOG CPS=> DpLoopInit, ICU ( 3.0 3.0 4.0.1) [dpxxdisp.c 1668]
***LOG Q0K=> DpMsAttach, mscon ( I3LSERVSAP1) [dpxxdisp.c 12364]
DpStartStopMsg: send start message (myname is >I3LSERVSAP1_CHE_00 <)
DpStartStopMsg: start msg sent
CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
CCMS: Initalizing shared memory of size 60000000 for monitoring segment.
CCMS: Checking Downtime Configuration of Monitoring Segment.
CCMS: start to initalize 3.X shared alert area (first segment).
DpMsgAdmin: Set release to 7000, patchlevel 0
MBUF state PREPARED
MBUF component UP
DpMBufHwIdSet: set Hardware-ID
***LOG Q1C=> DpMBufHwIdSet [dpxxmbuf.c 1050]
DpMsgAdmin: Set patchno for this platform to 175
Release check o.K.
Sun Dec 07 13:06:39 2008
my types changed after wp death/restart 0xbf --> 0xbe
my types changed after wp death/restart 0xbe --> 0xbc
my types changed after wp death/restart 0xbc --> 0xb8
my types changed after wp death/restart 0xb8 --> 0xb0
my types changed after wp death/restart 0xb0 --> 0xa0
my types changed after wp death/restart 0xa0 --> 0x80
DP_FATAL_ERROR => DpWPCheck: no more work processes
DISPATCHER EMERGENCY SHUTDOWN ***
increase tracelevel of WPs
NiWait: sleep (10000ms) ...
NiISelect: timeout 10000ms
NiISelect: maximum fd=1513
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Sun Dec 07 13:06:49 2008
NiISelect: TIMEOUT occured (10000ms)
dump system status
Workprocess Table (long) Sun Dec 07 07:36:49 2008
========================
No Ty. Pid Status Cause Start Err Sem CPU Time Program Cl User Action Table
0 DIA 6120 Ended no 1 0 0
1 DIA 2860 Ended no 1 0 0
2 DIA 6020 Ended no 1 0 0
3 DIA 5632 Ended no 1 0 0
4 DIA 588 Ended no 1 0 0
5 DIA 6016 Ended no 1 0 0
6 UPD 484 Ended no 1 0 0
7 ENQ 2268 Ended no 1 0 0
8 BTC 584 Ended no 1 0 0
9 BTC 6064 Ended no 1 0 0
10 BTC 4228 Ended no 1 0 0
11 BTC 5980 Ended no 1 0 0
12 SPO 1984 Ended no 1 0 0
13 UP2 5996 Ended no 1 0 0
Dispatcher Queue Statistics Sun Dec 07 07:36:49 2008
===========================
--------++++--
+
Typ
now
high
max
writes
reads
--------++++--
+
NOWP
0
2
2000
6
6
--------++++--
+
DIA
5
5
2000
5
0
--------++++--
+
UPD
0
0
2000
0
0
--------++++--
+
ENQ
0
0
2000
0
0
--------++++--
+
BTC
0
0
2000
0
0
--------++++--
+
SPO
0
0
2000
0
0
--------++++--
+
UP2
0
0
2000
0
0
--------++++--
+
max_rq_id 12
wake_evt_udp_now 0
wake events total 8, udp 7 ( 87%), shm 1 ( 12%)
since last update total 8, udp 7 ( 87%), shm 1 ( 12%)
Dump of tm_adm structure: Sun Dec 07 07:36:49 2008
=========================
Term uid man user term lastop mod wp ta a/i (modes)
Workprocess Comm. Area Blocks Sun Dec 07 07:36:49 2008
=============================
Slots: 300, Used: 1, Max: 0
--------++--
+
id
owner
pid
eyecatcher
--------++--
+
0
DISPATCHER
-1
WPCAAD000
NiWait: sleep (5000ms) ...
NiISelect: timeout 5000ms
NiISelect: maximum fd=1513
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Sun Dec 07 13:06:54 2008
NiISelect: TIMEOUT occured (5000ms)
DpHalt: shutdown server >I3LSERVSAP1_CHE_00 < (normal)
DpJ2eeDisableRestart
DpModState: buffer in state MBUF_PREPARED
NiBufSend starting
NiIWrite: hdl 2 sent data (wrt=110,pac=1,MESG_IO)
MsINiWrite: sent 110 bytes
MsIModState: change state to SHUTDOWN
DpModState: change server state from STARTING to SHUTDOWN
Switch off Shared memory profiling
ShmProtect( 57, 3 )
ShmProtect(SHM_PROFILE, SHM_PROT_RW
ShmProtect( 57, 1 )
ShmProtect(SHM_PROFILE, SHM_PROT_RD
DpWakeUpWps: wake up all wp's
Stop work processes
Stop gateway
killing process (6084) (SOFT_KILL)
Stop icman
killing process (6128) (SOFT_KILL)
Terminate gui connections
wait for end of work processes
wait for end of gateway
[DpProcDied] Process lives (PID:6084 HANDLE:1484)
waiting for termination of gateway ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1513
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Sun Dec 07 13:06:55 2008
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process died (PID:6084 HANDLE:1484)
wait for end of icman
[DpProcDied] Process lives (PID:6128 HANDLE:1488)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1513
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Sun Dec 07 13:06:56 2008
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:6128 HANDLE:1488)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1513
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Sun Dec 07 13:06:57 2008
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:6128 HANDLE:1488)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1513
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Sun Dec 07 13:06:58 2008
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:6128 HANDLE:1488)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1513
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Sun Dec 07 13:06:59 2008
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:6128 HANDLE:1488)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1513
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Sun Dec 07 13:07:00 2008
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:6128 HANDLE:1488)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1513
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Sun Dec 07 13:07:01 2008
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:6128 HANDLE:1488)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1513
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Sun Dec 07 13:07:02 2008
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:6128 HANDLE:1488)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1513
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Sun Dec 07 13:07:03 2008
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:6128 HANDLE:1488)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1513
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Sun Dec 07 13:07:04 2008
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:6128 HANDLE:1488)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1513
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Sun Dec 07 13:07:05 2008
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:6128 HANDLE:1488)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1513
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Sun Dec 07 13:07:06 2008
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process died (PID:6128 HANDLE:1488)
DpStartStopMsg: send stop message (myname is >I3LSERVSAP1_CHE_00 <)
NiIMyHostName: hostname = 'I3LSERVSAP1'
AdGetSelfIdentRecord: > <
AdCvtRecToExt: opcode 60 (AD_SELFIDENT), ser 0, ex 0, errno 0
AdCvtRecToExt: opcode 4 (AD_STARTSTOP), ser 0, ex 0, errno 0
DpConvertRequest: net size = 189 bytes
NiBufSend starting
NiIWrite: hdl 2 sent data (wrt=562,pac=1,MESG_IO)
MsINiWrite: sent 562 bytes
send msg (len 110+452) to name -, type 4, key -
DpStartStopMsg: stop msg sent
NiIRead: hdl 2 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 2 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 2 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 2 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 2 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 2 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 2 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 2 recv would block (errno=EAGAIN)
NiIRead: read for hdl 2 timed out (0ms)
DpHalt: no more messages from the message server
DpHalt: send keepalive to synchronize with the message server
NiBufSend starting
NiIWrite: hdl 2 sent data (wrt=114,pac=1,MESG_IO)
MsINiWrite: sent 114 bytes
send msg (len 110+4) to name MSG_SERVER, type 0, key -
MsSndName: MS_NOOP ok
Send 4 bytes to MSG_SERVER
NiIRead: hdl 2 recv would block (errno=EAGAIN)
NiIPeek: peek successful for hdl 2 (r)
NiIRead: hdl 2 received data (rcd=114,pac=1,MESG_IO)
NiBufIIn: NIBUF len=114
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 114 bytes
MSG received, len 110+4, flag 3, from MSG_SERVER , typ 0, key -
Received 4 bytes from MSG_SERVER
Received opcode MS_NOOP from msg_server, reply MSOP_OK
MsOpReceive: ok
MsSendKeepalive : keepalive sent to message server
NiIRead: hdl 2 recv would block (errno=EAGAIN)
Sun Dec 07 13:07:07 2008
NiIPeek: peek for hdl 2 timed out (r; 1000ms)
NiIRead: read for hdl 2 timed out (1000ms)
DpHalt: no more messages from the message server
DpHalt: sync with message server o.k.
detach from message server
***LOG Q0M=> DpMsDetach, ms_detach () [dpxxdisp.c 12710]
NiBufSend starting
NiIWrite: hdl 2 sent data (wrt=110,pac=1,MESG_IO)
MsINiWrite: sent 110 bytes
MsIDetach: send logout to msg_server
MsIDetach: call exit function
DpMsShutdownHook called
NiBufISelUpdate: new MODE -- (r-) for hdl 2 in set0
SiSelNSet: set events of sock 1420 to: ---
NiBufISelRemove: remove hdl 2 from set0
SiSelNRemove: removed sock 1420 (pos=2)
SiSelNRemove: removed sock 1420
NiSelIRemove: removed hdl 2
MBUF state OFF
AdGetSelfIdentRecord: > <
AdCvtRecToExt: opcode 60 (AD_SELFIDENT), ser 0, ex 0, errno 0
AdCvtRecToExt: opcode 40 (AD_MSBUF), ser 0, ex 0, errno 0
AdCvtRecToExt: opcode 40 (AD_MSBUF), ser 0, ex 0, errno 0
blks_in_queue/wp_ca_blk_no/wp_max_no = 1/300/14
LOCK WP ca_blk 1
make DISP owner of wp_ca_blk 1
DpRqPutIntoQueue: put request into queue (reqtype 1, prio LOW, rq_id 15)
MBUF component DOWN
NiICloseHandle: shutdown and close hdl 2 / sock 1420
NiBufIClose: clear extension for hdl 2
MsIDetach: detach MS-system
cleanup EM
EsCleanup ....
EmCleanup() -> 0
Es2Cleanup: Cleanup ES2
***LOG Q05=> DpHalt, DPStop ( 1536) [dpxxdisp.c 10908]
Good Bye .....
dev_w0::
trc file: "dev_w0", trc level: 1, release: "700"
ACTIVE TRACE LEVEL 1
ACTIVE TRACE COMPONENTS all, MJ
B
B Sun Dec 07 13:05:59 2008
B create_con (con_name=R/3)
B Loading DB library 'F:\usr\sap\CHE\DVEBMGS00\exe\dboraslib.dll' ...
B Library 'F:\usr\sap\CHE\DVEBMGS00\exe\dboraslib.dll' loaded
B Version of 'F:\usr\sap\CHE\DVEBMGS00\exe\dboraslib.dll' is "700.08", patchlevel (0.167)
B New connection 0 created
M sysno 00
M sid CHE
M systemid 560 (PC with Windows NT)
M relno 7000
M patchlevel 0
M patchno 175
M intno 20050900
M make: multithreaded, Unicode, optimized
M pid 6120
M
M kernel runs with dp version 241000(ext=110000) (@(#) DPLIB-INT-VERSION-241000-UC)
M length of sys_adm_ext is 576 bytes
M ***LOG Q0Q=> tskh_init, WPStart (Workproc 0 6120) [dpxxdisp.c 1323]
I MtxInit: 30000 0 0
M DpSysAdmExtCreate: ABAP is active
M DpSysAdmExtCreate: VMC (JAVA VM in WP) is not active
M DpShMCreate: sizeof(wp_adm) 23856 (1704)
M DpShMCreate: sizeof(tm_adm) 4415616 (21968)
M DpShMCreate: sizeof(wp_ca_adm) 24064 (80)
M DpShMCreate: sizeof(appc_ca_adm) 8000 (80)
M DpCommTableSize: max/headSize/ftSize/tableSize=500/8/528056/528064
M DpShMCreate: sizeof(comm_adm) 528064 (1048)
M DpSlockTableSize: max/headSize/ftSize/fiSize/tableSize=0/0/0/0/0
M DpShMCreate: sizeof(slock_adm) 0 (96)
M DpFileTableSize: max/headSize/ftSize/tableSize=0/0/0/0
M DpShMCreate: sizeof(file_adm) 0 (72)
M DpShMCreate: sizeof(vmc_adm) 0 (1544)
M DpShMCreate: sizeof(wall_adm) (38456/34360/64/184)
M DpShMCreate: sizeof(gw_adm) 48
M DpShMCreate: SHM_DP_ADM_KEY (addr: 06840040, size: 5081056)
M DpShMCreate: allocated sys_adm at 06840040
M DpShMCreate: allocated wp_adm at 06842118
M DpShMCreate: allocated tm_adm_list at 06847E48
M DpShMCreate: allocated tm_adm at 06847E78
M DpShMCreate: allocated wp_ca_adm at 06C7DEF8
M DpShMCreate: allocated appc_ca_adm at 06C83CF8
M DpShMCreate: allocated comm_adm at 06C85C38
M DpShMCreate: system runs without slock table
M DpShMCreate: system runs without file table
M DpShMCreate: allocated vmc_adm_list at 06D06AF8
M DpShMCreate: allocated gw_adm at 06D06B38
M DpShMCreate: system runs without vmc_adm
M DpShMCreate: allocated ca_info at 06D06B68
M DpShMCreate: allocated wall_adm at 06D06B70
M rdisp/queue_size_check_value : -> off
M ThTaskStatus: rdisp/reset_online_during_debug 0
X EmInit: MmSetImplementation( 2 ).
X MM global diagnostic options set: 0
X <ES> client 0 initializing ....
X Using implementation view
X <EsNT> Using memory model view.
M <EsNT> Memory Reset disabled as NT default
X ES initialized.
M
M Sun Dec 07 13:06:00 2008
M ThInit: running on host I3LSERVSAP1
M
M Sun Dec 07 13:06:01 2008
M calling db_connect ...
C Prepending F:\usr\sap\CHE\DVEBMGS00\exe to Path.
C Oracle Client Version: '10.2.0.1.0'
C Client NLS settings: AMERICAN_AMERICA.UTF8
C Logon as OPS$-user to get SAPSR3's password
C Connecting as /@CHE on connection 0 (nls_hdl 0) ... (dbsl 700 030508)
C Nls CharacterSet NationalCharSet C EnvHp ErrHp ErrHpBatch
C 0 UTF8 1 0672A1A8 0672F744 0672EFCC
C Attaching to DB Server CHE (con_hdl=0,svchp=0672EF18,srvhp=06740B04)
C Starting user session (con_hdl=0,svchp=0672EF18,srvhp=06740B04,usrhp=06755878)
C Now '/@CHE' is connected: con_hdl=0, nls_hdl=0, session_id=85.
C Got SAPSR3's password from OPS$-user
C Disconnecting from connection 0 ...
C Closing user session (con_hdl=0,svchp=0672EF18,usrhp=06755878)
C Now I'm disconnected from ORACLE
C Connecting as SAPSR3/<pwd>@CHE on connection 0 (nls_hdl 0) ... (dbsl 700 030508)
C Nls CharacterSet NationalCharSet C EnvHp ErrHp ErrHpBatch
C 0 UTF8 1 0672A1A8 0672F744 0672EFCC
C Starting user session (con_hdl=0,svchp=0672EF18,srvhp=06740B04,usrhp=06755878)
C Now 'SAPSR3/<pwd>@CHE' is connected: con_hdl=0, nls_hdl=0, session_id=85.
C Database NLS settings: AMERICAN_AMERICA.UTF8
C DB instance CHE is running on I3LSERVSAP1 with ORACLE version 10.2.0.2.0 since DEC 07, 2008, 12:36:31
B Connection 0 opened (DBSL handle 0)
B Wp Hdl ConName ConId ConState TX PRM RCT TIM MAX OPT Date Time DBHost
B 000 000 R/3 000000000 ACTIVE NO YES NO 000 255 255 20081207 130601 I3LSERVSAP1
C build_stmt: reallocating stmt buffer: 256 -> 2000 characters
M db_connect o.k.
M ICT: exclude compression: .zip,.cs,.rar,.arj,.z,.gz,.tar,.lzh,.cab,.hqx,.ace,.jar,.ear,.war,.css,.pdf,.js,.gzip,.uue,.bz2,.iso,.sda,.sar,.gif
I MtxInit: 0 0 0
M SHM_PRES_BUF (addr: 0B3A0040, size: 4400000)
I *** ERROR => [MapOsShm] Can't find free space for Shared Memory (Size=720000 KB)
 [shmnt.c 2174]
I *** ERROR => [CreateOsShm] MapViewOfFile(Key=9,Handle=0x000004DC) failed with Err=0
 [shmnt.c 2174]
I *** ERROR => ShmCreate: Create (9,737280000,3) failed [shmnt.c 506]
Memory diagnostic *
Systeminformation
Processor-Typ : Intel Pentium Pro
Processor-Count : 8
Operating System : NT 5.2, Build 3790
Service Pack : Service Pack 2
NT Pagefile Informations
Config. minimum size : 12570624 K
Config. maximum size : 12570624 K
Avail. maximum size : 12570624 K
Num
Pagefile
Min.Size
Max.Size
Avail.Max
Curr.Size
1
c:\pagefile.sys
4190208 K
4190208 K
4190208 K
4190208 K
2
d:\pagefile.sys
4190208 K
4190208 K
4190208 K
4190208 K
3
f:\pagefile.sys
4190208 K
4190208 K
4190208 K
4190208 K
NT Task Manager Informations
Total Handles : 0
Total Threads : 0
Total Processes : 0
Commit Charge Total : 6571584 K
Commit Charge Limit : 15822776 K
Commit Charge Peak : 7495116 K
Phys.Memory Total : 54 K
Phys.Memory Available : 93650276 K
File Cache : 17399116 K
Kernel Memory Total : 2084222616 K
Kernel Memory Paged : 0 K
Kernel Memory Nonpaged : 93650304 K
Memory usage of current process
Total virt.address space : 2097024 K
Avail.virt.address space : 837328 K
Private Pages : 0 K
Total heap size : 14532 K
Virtual memory regions : 0 K
Uncommitted heap memory : 6440 K
Allocated heap memory : 6850 K
Moveable heap memory : 0 K
DDE shared heap memory : 0 K
Memory usage of all processes
PID
Image
Instance
Work.Set
WS Peak
Priv.Pages
PP Peak
Pg Fault
1940
sapstartsrv.exe
15956 K
15956 K
18656 K
18700 K
4
5716
msg_server.EXE
[MS] CHE_00
8508 K
8508 K
11000 K
11000 K
2
1536
disp+work.EXE
[DP] CHE_00
93256 K
93256 K
69540 K
69540 K
22
5772
igswd.EXE
[**] CHE_00
2796 K
3048 K
1436 K
1724 K
0
1304
igsmux.exe
12012 K
12012 K
13032 K
13032 K
2
5696
igspw.exe
2536 K
2536 K
2336 K
2336 K
0
5688
igspw.exe
2536 K
2536 K
2336 K
2336 K
0
6084
gwrd.EXE
[GW] CHE_00
10164 K
10164 K
9996 K
17924 K
2
6128
icman.EXE
[**] CHE_00
86128 K
86128 K
88096 K
88096 K
21
6120
disp+work.EXE
31808 K
31904 K
82200 K
85356 K
7
2860
disp+work.EXE
[WP] CHE_00
30604 K
30604 K
81656 K
85356 K
7
6020
disp+work.EXE
[WP] CHE_00
16080 K
16080 K
67372 K
67372 K
3
5632
disp+work.EXE
[WP] CHE_00
16104 K
16104 K
67372 K
67372 K
3
588
disp+work.EXE
[WP] CHE_00
28804 K
28804 K
80672 K
85356 K
7
6016
disp+work.EXE
[WP] CHE_00
16084 K
16084 K
67372 K
67372 K
3
484
disp+work.EXE
[WP] CHE_00
16084 K
16084 K
67372 K
67372 K
3
2268
disp+work.EXE
[WP] CHE_00
16080 K
16080 K
67372 K
67372 K
3
584
disp+work.EXE
[WP] CHE_00
19112 K
19112 K
85360 K
85360 K
4
6064
disp+work.EXE
[WP] CHE_00
30972 K
30972 K
81696 K
85356 K
7
4228
disp+work.EXE
[WP] CHE_00
30376 K
30376 K
81488 K
85356 K
7
5980
disp+work.EXE
[WP] CHE_00
16080 K
16080 K
67372 K
67372 K
3
1984
disp+work.EXE
[WP] CHE_00
16080 K
16080 K
67372 K
67372 K
3
5996
disp+work.EXE
[WP] CHE_00
16080 K
16080 K
67372 K
67372 K
3
Sum
534240 K
1248476 K
M *** ERROR => ThShMCreate: ShmCreate SHM_ROLL_AREA_KEY failed [thxxhead.c 2598]
M *** ERROR => ThIPCInit: ThShMCreate [thxxhead.c 2095]
M ***LOG R19=> ThInit, ThIPCInit ( TSKH-IPC-000001) [thxxhead.c 1532]
M in_ThErrHandle: 1
M *** ERROR => ThInit: ThIPCInit (step 1, th_errno 17, action 3, level 1) [thxxhead.c 10534]
M
M Info for wp 0
M
M pid = 6120
M severity = 0
M status = 0
M stat = WP_RUN
M waiting_for = NO_WAITING
M reqtype = DP_RQ_DIAWP
M act_reqtype = NO_REQTYPE
M rq_info = 0
M tid = -1
M mode = 255
M len = -1
M rq_id = 65535
M rq_source =
M last_tid = 0
M last_mode = 0
M semaphore = 0
M act_cs_count = 0
M csTrack = 0
M csTrackRwExcl = 0
M csTrackRwShrd = 0
M mode_cleaned_counter = 0
M control_flag = 0
M int_checked_resource(RFC) = 0
M ext_checked_resource(RFC) = 0
M int_checked_resource(HTTP) = 0
M ext_checked_resource(HTTP) = 0
M report = > <
M action = 0
M tab_name = > <
M attachedVm = no VM
M
M *****************************************************************************
M *
M * LOCATION SAP-Server I3LSERVSAP1_CHE_00 on host I3LSERVSAP1 (wp 0)
M * ERROR ThInit: ThIPCInit
M *
M * TIME Sun Dec 07 13:06:01 2008
M * RELEASE 700
M * COMPONENT Taskhandler
M * VERSION 1
M * RC 17
M * MODULE thxxhead.c
M * LINE 10754
M * COUNTER 1
M *
M *****************************************************************************
M
M PfStatDisconnect: disconnect statistics
M Entering TH_CALLHOOKS
M ThCallHooks: call hook >BtcCallLgCl< for event BEFORE_DUMP
M ThCallHooks: call hook >ThrSaveSPAFields< for event BEFORE_DUMP
M *** ERROR => ThrSaveSPAFields: no valid thr_wpadm [thxxrun1.c 723]
M *** ERROR => ThCallHooks: event handler ThrSaveSPAFields for event BEFORE_DUMP failed [thxxtool3.c 261]
M Entering ThSetStatError
M ThIErrHandle: do not call ThrCoreInfo (no_core_info=0, in_dynp_env=0)
M Entering ThReadDetachMode
M call ThrShutDown (1)...
M ***LOG Q02=> wp_halt, WPStop (Workproc 0 6120) [dpnttool.c 333]

Hi Chandra
If you look at the DEV_w0 log you can see the work process are not comming you as they are not getting enough shared memory see this error message
" Can't find free space for Shared Memory (Size=720000 KB) "
Please review the parameter changes made by you in Instance profile before restart of instace. Check the values of these parameters and if you are not sure of the value changed by you undo the parameter changes made before the instace restart
Restart the instance again after these changes in instance profile. for now you can change the instace profile file from OS but don't forget to import this changed profile when instace is up
if you did not changed any Profile parameters, check the physical memory available. chance could you some hardware memory issue. get your os team to check.
Its a clear case of memory issue ..
Rajeev

File Adapter BPEL Process getting switched off

The file adapter BPEL process reads a csv file which has a series of records in itfrom /xfer/chroot/data/aramex/accountUpdate/files. In between reading the files, the BPEL process gets switched off. The below snippet is the error we found in the domain.log. Anybody can you please suggest what to do?
<2010-11-25 16:22:28,025> <WARN> <PreActivation.collaxa.cube.ws> <File Adapter::Outbound>
java.io.FileNotFoundException: /xfer/chroot/data/aramex/accountUpdate/files/VFQ-251120101_1000.csv (No such file or directory)
at java.io.FileInputStream.open(Native Method)
at java.io.FileInputStream.<init>(FileInputStream.java:106)
at oracle.tip.adapter.file.FileUtil.copyFile(FileUtil.java:947)
at oracle.tip.adapter.file.inbound.ProcessWork.defaultArchive(ProcessWork.java:2341)
at oracle.tip.adapter.file.inbound.ProcessWork.doneProcessing(ProcessWork.java:614)
at oracle.tip.adapter.file.inbound.ProcessWork.processMessages(ProcessWork.java:445)
at oracle.tip.adapter.file.inbound.ProcessWork.run(ProcessWork.java:227)
at oracle.tip.adapter.fw.jca.work.WorkerJob.go(WorkerJob.java:51)
at oracle.tip.adapter.fw.common.ThreadPool.run(ThreadPool.java:280)
at java.lang.Thread.run(Thread.java:619)
<2010-11-25 16:22:28,025> <INFO> <PreActivation.collaxa.cube.ws> <File Adapter::Outbound> Processer thread calling onFatalError with exception /xfer/chroot/data/aramex/accountUpdate/files/VFQ-251120101_1000.csv (No such file or directory)
<2010-11-25 16:22:28,025> <FATAL> <PreActivation.collaxa.cube.activation> <AdapterFramework::Inbound> [Read_ptt::Read(root)]Resource Adapter requested Process shutdown!
<2010-11-25 16:22:28,025> <INFO> <PreActivation.collaxa.cube.activation> <AdapterFramework::Inbound> Adapter Framework instance: OraBPEL - performing endpointDeactivation for portType=Read_ptt, operation=Read
<2010-11-25 16:22:28,025> <INFO> <PreActivation.collaxa.cube.ws> <File Adapter::Outbound> Endpoint De-activation called in adapter for endpoint : /xfer/chroot/data/aramex/accountUpdate/files/
<2010-11-25 16:22:28,095> <WARN> <PreActivation.collaxa.cube.ws> <File Adapter::Outbound> ProcessWork::Delete failed, the operation will be retried for max of [2] times
<2010-11-25 16:22:28,095> <WARN> <PreActivation.collaxa.cube.ws> <File Adapter::Outbound>
ORABPEL-11042
File deletion failed.
File : /xfer/chroot/data/aramex/accountUpdate/files/VFQ-251120101_1000.csv as it does not exist. could not be deleted.
Delete the file and restart server. Contact oracle support if error is not fixable.
at oracle.tip.adapter.file.FileUtil.deleteFile(FileUtil.java:279)
at oracle.tip.adapter.file.FileUtil.deleteFile(FileUtil.java:177)
at oracle.tip.adapter.file.FileAgent.deleteFile(FileAgent.java:223)
at oracle.tip.adapter.file.inbound.FileSource.deleteFile(FileSource.java:245)
at oracle.tip.adapter.file.inbound.ProcessWork.doneProcessing(ProcessWork.java:655)
at oracle.tip.adapter.file.inbound.ProcessWork.processMessages(ProcessWork.java:445)
at oracle.tip.adapter.file.inbound.ProcessWork.run(ProcessWork.java:227)
at oracle.tip.adapter.fw.jca.work.WorkerJob.go(WorkerJob.java:51)
at oracle.tip.adapter.fw.common.ThreadPool.run(ThreadPool.java:280)
at java.lang.Thread.run(Thread.java:619)
<2010-11-25 16:22:28,315> <ERROR> <PreActivation.collaxa.cube> <BaseCubeSessionBean::logError> Error while invoking bean "cube delivery": Process state off.
The process class "BulkAccountUpdateFileConsumer" (revision "1.0" ) has not been turned on. No operations on the process or any instances belonging to the process may be performed if the process is off.
Please consult your administrator if this process has been turned off inadvertently.

This patch is not for 10.1.3.1.
I have provided a response to on the following post
BPEL Process Going into Dead State Automatically.
cheers
James

I can't print my statements from banking websites - the option to print (drop down file menu) from the website is greyed out

I do my banking online, and have previously been able to print my statements off the website. Since the last update, although the page shows in the browser as normal, the option to print from the drop-down file menu is greyed out and I cannot print anything, even if I try and select a portion. It is not a problem with the website as I can print without a problem in another browser program. This problem has now persisted for quite a while with no resolution over time. How do I get Firefox to allow print from a secure website (I assume that is the problem?) It occurs with more than one secure site (two different banks)

I have the same problem... not being able to print website 'Print' pages. I have read carefully the above link and have followed the reset directions in about:config, but I still cannot print in Firefox. Both Google Chrome and IE work perfectly every time. I have verified that the correct printer is selected and that the margins are in order (0.5 all around happen to be what mine are set for). I have resorted to use the Firefox Add On "View this Page in IE" whenever I need to print something. Works like a charm, but come on... it should work in Firefox too! I know there is some setting or something, but the Problems_printing_web_pages link had nothing there that worked for me.

DpJ2eeEmergencyShutdown: j2ee state = SHUTDOWN - how to make it STARTED

Hi,
I have an ABAP+Java SAP ERP 2005 server.
After having made a Java Add-in installation w/o success, I stoped the installation.
Now in this server, process Dispatcher is always in yellow with status "Running, Message Server connection ok, Dialog Queue time: 0.00 sec, J2EE status info unavailable".
How can I fix this error to make J2EE started?
Here the trace:
trc file: "dev_disp", trc level: 1, release: "700"
sysno 00
sid BP1
systemid 560 (PC with Windows NT)
relno 7000
patchlevel 0
patchno 102
intno 20050900
make: multithreaded, Unicode, optimized
pid 2724
Fri Sep 14 14:37:18 2007
kernel runs with dp version 224000(ext=109000) (@(#) DPLIB-INT-VERSION-224000-UC)
length of sys_adm_ext is 572 bytes
SWITCH TRC-HIDE on ***
***LOG Q00=> DpSapEnvInit, DPStart (00 2724) [dpxxdisp.c 1239]
 shared lib "dw_xml.dll" version 102 successfully loaded
 shared lib "dw_xtc.dll" version 102 successfully loaded
 shared lib "dw_stl.dll" version 102 successfully loaded
 shared lib "dw_gui.dll" version 102 successfully loaded
 shared lib "dw_mdm.dll" version 102 successfully loaded
rdisp/softcancel_sequence : -> 0,5,-1
use internal message server connection to port 3900
Fri Sep 14 14:37:24 2007
WARNING => DpNetCheck: NiAddrToHost(1.0.0.0) took 5 seconds
***LOG GZZ=> 1 possible network problems detected - check tracefile and adjust the DNS settings [dpxxtool2.c 5355]
MtxInit: 30000 0 0
DpSysAdmExtInit: ABAP is active
DpSysAdmExtInit: VMC (JAVA VM in WP) is not active
DpIPCInit2: start server >SAP0806_BP1_00 <
DpShMCreate: sizeof(wp_adm) 15752 (1432)
DpShMCreate: sizeof(tm_adm) 4232256 (21056)
DpShMCreate: sizeof(wp_ca_adm) 24000 (80)
DpShMCreate: sizeof(appc_ca_adm) 8000 (80)
DpCommTableSize: max/headSize/ftSize/tableSize=500/8/528056/528064
DpShMCreate: sizeof(comm_adm) 528064 (1048)
DpSlockTableSize: max/headSize/ftSize/fiSize/tableSize=0/0/0/0/0
DpShMCreate: sizeof(slock_adm) 0 (96)
DpFileTableSize: max/headSize/ftSize/tableSize=0/0/0/0
DpShMCreate: sizeof(file_adm) 0 (72)
DpShMCreate: sizeof(vmc_adm) 0 (1520)
DpShMCreate: sizeof(wall_adm) (38456/34360/64/184)
DpShMCreate: sizeof(gw_adm) 48
DpShMCreate: SHM_DP_ADM_KEY (addr: 07AD0040, size: 4888864)
DpShMCreate: allocated sys_adm at 07AD0040
DpShMCreate: allocated wp_adm at 07AD1E80
DpShMCreate: allocated tm_adm_list at 07AD5C08
DpShMCreate: allocated tm_adm at 07AD5C38
DpShMCreate: allocated wp_ca_adm at 07EDF078
DpShMCreate: allocated appc_ca_adm at 07EE4E38
DpShMCreate: allocated comm_adm at 07EE6D78
DpShMCreate: system runs without slock table
DpShMCreate: system runs without file table
DpShMCreate: allocated vmc_adm_list at 07F67C38
DpShMCreate: allocated gw_adm at 07F67C78
DpShMCreate: system runs without vmc_adm
DpShMCreate: allocated ca_info at 07F67CA8
DpShMCreate: allocated wall_adm at 07F67CB0
MBUF state OFF
DpCommInitTable: init table for 500 entries
EmInit: MmSetImplementation( 2 ).
MM global diagnostic options set: 0
<ES> client 0 initializing ....
<ES> InitFreeList
<ES> block size is 1024 kByte.
Using implementation view
<EsNT> Memory Reset disabled as NT default
<ES> 2047 blocks reserved for free list.
ES initialized.
J2EE server info
start = TRUE
state = STARTED
pid = 3776
argv[0] = E:\usr\sap\BP1\DVEBMGS00\exe\jcontrol.EXE
argv[1] = E:\usr\sap\BP1\DVEBMGS00\exe\jcontrol.EXE
argv[2] = pf=E:\usr\sap\BP1\SYS\profile\BP1_DVEBMGS00_SAP0806
argv[3] = -DSAPSTART=1
argv[4] = -DCONNECT_PORT=2604
argv[5] = -DSAPSYSTEM=00
argv[6] = -DSAPSYSTEMNAME=BP1
argv[7] = -DSAPMYNAME=SAP0806_BP1_00
argv[8] = -DSAPPROFILE=E:\usr\sap\BP1\SYS\profile\BP1_DVEBMGS00_SAP0806
argv[9] = -DFRFC_FALLBACK=ON
argv[10] = -DFRFC_FALLBACK_HOST=localhost
start_lazy = 0
start_control = SAP J2EE startup framework
DpJ2eeStart: j2ee state = STARTED
rdisp/http_min_wait_dia_wp : 1 -> 1
***LOG CPS=> DpLoopInit, ICU ( 3.0 3.0 4.0.1) [dpxxdisp.c 1626]
***LOG Q0K=> DpMsAttach, mscon ( SAP0806) [dpxxdisp.c 11664]
DpStartStopMsg: send start message (myname is >SAP0806_BP1_00 <)
DpStartStopMsg: start msg sent
CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
CCMS: Initalizing shared memory of size 60000000 for monitoring segment.
CCMS: start to initalize 3.X shared alert area (first segment).
DpMsgAdmin: Set release to 7000, patchlevel 0
MBUF state PREPARED
MBUF component UP
DpMBufHwIdSet: set Hardware-ID
***LOG Q1C=> DpMBufHwIdSet [dpxxmbuf.c 1050]
DpMsgAdmin: Set patchno for this platform to 102
Release check o.K.
Fri Sep 14 14:37:28 2007
MBUF state ACTIVE
DpModState: change server state from STARTING to ACTIVE
Fri Sep 14 14:38:04 2007
DpJ2eeEmergencyShutdown: j2ee state = SHUTDOWN
Fri Sep 14 14:38:24 2007
J2EE server info
start = TRUE
state = STARTED
pid = 3408
argv[0] = E:\usr\sap\BP1\DVEBMGS00\exe\jcontrol.EXE
argv[1] = E:\usr\sap\BP1\DVEBMGS00\exe\jcontrol.EXE
argv[2] = pf=E:\usr\sap\BP1\SYS\profile\BP1_DVEBMGS00_SAP0806
argv[3] = -DSAPSTART=1
argv[4] = -DCONNECT_PORT=2671
argv[5] = -DSAPSYSTEM=00
argv[6] = -DSAPSYSTEMNAME=BP1
argv[7] = -DSAPMYNAME=SAP0806_BP1_00
argv[8] = -DSAPPROFILE=E:\usr\sap\BP1\SYS\profile\BP1_DVEBMGS00_SAP0806
argv[9] = -DFRFC_FALLBACK=ON
argv[10] = -DFRFC_FALLBACK_HOST=localhost
start_lazy = 0
start_control = SAP J2EE startup framework
DpJ2eeStart: j2ee state = STARTED
Fri Sep 14 14:38:44 2007
DpJ2eeEmergencyShutdown: j2ee state = SHUTDOWN

Hi Kalyan,
Unfortunately, I cannot find section "6.8.2.3 Deleting the Java Part of an SAP System" as you said.
All docs that I've just downloaded only have sections 6.8 & sub 6.8.1 as following:
- 6.8 Deleting an SAP System
 + 6.8.1 Running SAPinst to Delete an SAP System
Docs browsed are:
- Installation Guide - SAP NetWeaver 7.0 SR2 ABAP+Java / Java / ABAP on Windows - MS SQL Server
- Installation Guide - SAP SAP ERP 2005 SR2 ABAP+Java / Java / ABAP on Windows - MS SQL Server
So please show me the way to get the correct ones or send me via [email protected]
You answer is considered helpful.
Thanks,
Toan Do

Multiple statements from one connection causes ORA-0100 Maximum open cursor

HI,
I am creating a connection and trying to run 2 statements off the connection. The connection has autocommit as false as I want to commit only after the second statement commits successfully. Upon executing the second statement, I get the ORAC-0100: Maximum open cursor error. I have verified that I have closed all the Preparedstatement and ResultSet in the first statement.
My code looks like this:
Connection myConn = DriverManager.getConnection(jdbc:oracle:thin:.....); myConn.setAutoCommmit(false); Savepoint sp = myConn.setSavePoint("save1"); PreparedStatement pstmt = myConn.prepareStatement(...) ResultSet rs = pstmt.executeQuery(); while (rs.next()){ ..... } rs.close(); pstmt.close(); rs=null; pstmt=null; Statement stmt2 = myConn.createStatement(); sql="DELETE FROM TempTable..."; stmt2.executeUpdate(sql);
I put a breakpoint just before stmt.executeUpdate and verified the open cursor are below the threshold. And as soon as I execute stmt2.executeUpdate,I get the maximum cursor error. Also, I noticed that the number of open cursors jumps to the limit after stmt2.executeUpdate(sql) as verified by the following sql
select s.sid, s.username, a.value from v$sesstat a, v$statname b, v$session s where a.statistic# = b.statistic# and s.sid=a.sid and b.name = 'opened cursors current' and s.username = 'user_name';
Am I doing something wrong? Is there a better way to execute multiple statements using the same connection and commiting only after the last statement has executed successfully?

I believe you need to close your connection via myConn.close() as follows:
PreparedStatement pstmt=null;
ResultSet rs=null;
Connection myConn=null;
try{
myConn= //put code to get connection in this statement here
pstmt = myConn.prepareStatement(...)
rs = pstmt.executeQuery();
while (rs.next()){
}finally{
if(rs!=null)
rs.close();
if(pstmt!=null)
pstmt.close();
if(myConn!=null)
myConn.close();
}

Auto update stats disabled for a user Database in Sql server

While trying to improve the performance of few queries, we found via execution plan that there were lot of Index/Clustered index seeks. Therefore:
First thing we did, was to check our Re-indexing and update stats job which runs weekly for this user DB ( Around 400 GB in size and is used 24*5). The job was running fine.
Later when we ran SP_Blitz, we came to know that auto-update-stats is disabled for this user DB. We expected this to be a possible cause and change it from false to TRUE(Auto update stats)
Also, per SP_blitz there are user-created statistics for this DB. When ran the query to check how many, we saw around 7K user stats out there.
So my question would be 1) setting the Auto update stats to TRUE would require a reboot or once changed i need to track the performance and 2) Should we consider dropping those user created stats or manually look into them one by one.
How should we proceed on this, please suggest, thanks!

There may be good reasons for having auto-stats off, but those cases are not very common. It makes a little more sense to turn if off on table level. An example of the latter is a relatively small table, say < 100000 rows where not many new rows are added,
but the existing rows are being updated frequently. This will trigger autostats, but probably without much benefit.
But if you have a system which is very busy during peak times, you may not want autostats take resources during those hours. But if you turn off autostats, you will need to make sure that stats are updated in some other fashion.
Here is a query that you can use review when your statistics last were updated:
SELECT o.name, s.name, stats_date(o.object_id, s.stats_id) AS lastupdated
FROM sys.objects o
JOIN sys.stats s ON s.object_id = o.object_id
--WHERE s.user_created = 1
ORDER BY lastupdated
7000 user-created statistics sounds a little excessive, but I guess they were added to compensate for the autostats that SQL Server were not permitted to create. I would not recommend dropping these statistics, as SQL Server would spend cycles on recreating
them.
You should not have to restart SQL Server for the Auto-update stats setting to take effect; it takes effect immediately.
Erland Sommarskog, SQL Server MVP, [email protected]

Grayed out in State View SCOM 2012 R2

I want to display only the following items in a state view:
Critical
Warning
Unmonitored
Grayed out Computers/Servers
How do I do this?

Works perfect....
http://www.youtube.com/watch?v=4n9TiXoCCHU

Errors using weblogic sql driver: "No JDBC connection can be made because the transaction state is marked rollback"

One of our customers starts to encounter this error message recently.
We checked our log files. It seems that the error happens when
to obtain a jdbc connection. Have anyone seen similar problems
and knows how to fix it? thanks in advance.
We are using weblogic server 6.1sp2, and weblogic sql type 4 driver.
The functions that invoke the jdbc calls are stateless session bean
methods with their transaction attributes marked as Required.
There is no nested calls of these methods.
A partial stack trace we obtained is as following:
java.sql.SQLException: No JDBC connection can be made
because the transaction state is
Marked Rollback
 at weblogic.jdbc.jts.Connection.getOrCreateConnection(Connection.java:586)
 at weblogic.jdbc.jts.Connection.prepareStatement(Connection.java:115)
 at weblogic.jdbc.rmi.internal.ConnectionImpl.prepareStatement(ConnectionImpl.java:135)
 at weblogic.jdbc.rmi.SerialConnection.prepareStatement(SerialConnection.java:76)
lixin

Joseph Weinstein <[email protected]> wrote:
>
>
YuanHui Liu wrote:
Joe,
We got the exact same error message. The error came after we got theJDBC connection,
and trying to create statement off it.
It occurs intermitently when we are running another standalone JAVAapp to do
some end of day work, which results in the DB Server being very busy(90+%CPU
usage) for about 5 minutes. We see a surge of requests to the WLSJDBC Connection
pool. This would sometimes result in all our subsequent DB requeststo fail and
lead to a crash.
We are using WLS6.0SP1. I do not think there's a 30 seconds wait leadingto a
connection timeout that caused this(rather it is the end effect).
Can you give us a more detailed explanation? Is there a miscommunicationbetween
our DB(Sybase12) and WLS?Hi. It looks to you like it's after you get the connection, but really
it's when the server is
gettng the pool connection. For performance/synchronization reasons we
do a clever
delay: When your code asks for a pool connection we quickly give you
the pool wrapper,
but we delay actually reserving the real underlying DBMS connection until
your first
real need for a connection, at your first JDBC call, such as createStatement()
etc.
It is while waiting for a pool connection long enough for the transaction
coordinator
to have timed you out before you ever get a chance. It's nothing to do
with the
DBMS or even JDBC, I believe. I think the weblogic server either has
too few execute-threads
and/or too few CPU cycles to do the work load.
Okay, so there's a lazy initialization of the connection.
From reading our log I believe our failur is immediate rather
than waiting for 30+ seconds(the default setting) from the DB,
the timeout occurred later as a result. At the time either because the DB Server
is very busy.
Since we are running WLS6.0 we have only one connection pool,
we have defined a max of 150 threads in the pool. While this
is happening the DB Server is being pinned by an overnight job,
but the WLS Server is not busy at all. The DB and WLS resides
on different physical boxes.
We also have a thread dump from the WLS console when we rebooted the server, it
showed that we are hanging on to the thread & jdbc
connections after these exceptions has occurred instead of releasing them, note
"16083"(~4.5 hours) seconds has passed:
142 116222 Retry rollback request for tx: 'transaction=(IdHash=2963855,Name =
[EJB UserManagerBeanImpl.signalICUserServletHeartBeat()],Xid=30643:8f3838f3709bf53d,Status=Rolling
Back. [Reason = Unknown],numRepliesOwedMe=0,numRepliesOwedOthers=0,seconds since
begin=16083,seconds left=10,ServerResourceInfo[weblogic.jdbc.jts.Connection]=(state=started,assigned=server),SCInfo[server]=(state=active),properties=({weblogic.jdbc=t3://159.55.158.25:8005,
weblogic.transaction.name=[EJB UserManagerBeanImpl.signalICUserServletHeartBeat()]}))'
Scheduled Trigger
So I would argue this problem actually chewed up resources on the WLS server.
-Yuanhui Liu
>>
>>
Thanks.
-YuanHui Liu
Joseph Weinstein <[email protected]> wrote:
lixin wrote:
One of our customers starts to encounter this error message recently.
We checked our log files. It seems that the error happens when
to obtain a jdbc connection. Have anyone seen similar problems
and knows how to fix it? thanks in advance.
We are using weblogic server 6.1sp2, and weblogic sql type 4 driver.
The functions that invoke the jdbc calls are stateless session bean
methods with their transaction attributes marked as Required.
There is no nested calls of these methods.
A partial stack trace we obtained is as following:
java.sql.SQLException: No JDBC connection can be made
because the transaction state is
Marked Rollback
at weblogic.jdbc.jts.Connection.getOrCreateConnection(Connection.java:586)Hi. This sounds like a JVM thread starvation issue, and/or a server
load
issue. What is
happening is that the transaction is started, and times out beforethe
SSB even gets to
the first JDBC work. I would first verify that the customer is using
the very latest JVM
available for the machine.
Joe Weinstein
at weblogic.jdbc.jts.Connection.prepareStatement(Connection.java:115)
at weblogic.jdbc.rmi.internal.ConnectionImpl.prepareStatement(ConnectionImpl.java:135)
at weblogic.jdbc.rmi.SerialConnection.prepareStatement(SerialConnection.java:76)
lixin

VM's state Off-Critical

Similar Messages

Maybe you are looking for