Vmware 3.0 and ubuntu 9.10

i installed ubuntu and it worked fine. then i shut it down and quit vmware. the next-time i tried to turn on ubuntu it asked for my password, which i put in. it then seemed to start to load only to take me back to the log in and asking for my password again.
now i cannot get into ubuntu. i reinstalled it and the same thing happened. anyone have any ideas? i went to the support page at vmware- but they never responded (4 days later). thanks.

Dear all,
I just would like to inform you that I was able to solve the problem. The error was caused by the extraction of the RAR files, which was not completely done.
Thank you,
Bernd

Similar Messages

  • Could use help dual booting windows 8 and ubuntu 13.04

    I have a Lenovo G580 with windows 8 + Ubuntu 13.04 installed. I've been trying to get Dual-boot to work for the past few hours with no success. I've been following this guide. After setting up the partitions similar to the ones in the guide i downloaded easyBCD on windows 8. I then added Ubuntu 13.04 to the grub menu. When i restart my laptop i get the menu with lenovo recovery, windows 8, and Ubuntu(not Ubuntu 13.04 like i labeled) when clicking Ubuntu it says windows failed to load, insert media for recovery. I can't do anything to access Ubuntu at this point. I don't know what it is i'm doing wrong but could use some help. Below are some pictures of the process. I'll post any needed info that i may have forgotten. When choosing OS it's in uefi mode.
    partitions
    OS's

    I have a Lenovo G580 with windows 8 + Ubuntu 13.04 installed. I've been trying to get Dual-boot to work for the past few hours with no success. I've been following this guide. After setting up the partitions similar to the ones in the guide i downloaded easyBCD on windows 8. I then added Ubuntu 13.04 to the grub menu. When i restart my laptop i get the menu with lenovo recovery, windows 8, and Ubuntu(not Ubuntu 13.04 like i labeled) when clicking Ubuntu it says windows failed to load, insert media for recovery. I can't do anything to access Ubuntu at this point. I don't know what it is i'm doing wrong but could use some help. Below are some pictures of the process. I'll post any needed info that i may have forgotten. When choosing OS it's in uefi mode.
    partitions
    OS's

  • T430s fingerprint reader fails in both windows 7 (64 bit) and ubuntu.

    Hi, 
    I have 4 months with my new t430s, and so far so good, I created a partition to instal ubuntu and I was able to have the finger print reader work in it. 
    The last week I left the laptop's battery to drain completely, but I did not notice it... I tried to wake it up but my fingerprint would not turn it on... I plug the charger on and the laptop started working again but now, my fingerprint log on was disabled, I had to type my pasword to log in...
    From that moment on, this issue consistently occurs in both windows & and ubuntu...
    The funny thing is that I can still turn on the laptop with my finger, the fingerprint reader indicator leds are working but the device only works to start the laptop. I have tried to delete the fingerprint data from teh BIOS, but I can still start the laptop, so I dont think this clear data command on the BIOS is doing anything...
    I have tried re-installing the device, updating the driver, etc and nothing works, the device appears as unnavailable on the windows biometric devices section of my control panel, so I cannot enroll any new finger print using the lenovo fingerprint software since I get these 3 errors in any attempt:
    E7210005 Cannot enroll user.
    E7210005 Cannot update passport.
    E7210005 Cannot find fingerprint sensor device.
    Any ideas?
    Is there a way to reset my device from the BIOS so al its data and its state is cleared?
    Thanks!
    Roberto O.

    rortegah
    I have heard of this exact situation one other time, where fingerprint sensor stops working properly after PC unexpectedly turns off due to low battery.  I think your fingerprint sensor has malfunctioned and needs replacement under warranty.  Currently, I do not know of any other solution.
    But can you please tell me:
    1.  how many fingers do you have enrolled?
    2.  do you use any BIOS passwords (such as administrator password, power-on password, or HDD password)?

  • IdeaPad Z370 and Ubuntu 11.10 64 bit - problem with volume buttons

    I recently bought my new Lenovo IdeaPad Z370 without operating system and installed Ubuntu 11.10 64 bit (the pre-installed system was FreeDOS which I decided to remove).
    Nearly all is working fine. The only exception are the volume keys: pressing them does start adjusting the volume, but causes a system problem. If I press sound up, the speakers move to immediately to the maximum volume and behave as it I was continuing to press the button.
    The same happens when pressing the volume down or sound off buttons. It is then not possible any more to use the keyboard or type anyting, nor change the volume using the touchpad and Ubuntu's speaker symbol. It is also not possible any more to shut down the computer using Ubuntu's virtual shutdown button, but with the real button on the computer.
    The touchpad is still working and after putting the computer briefly into standby the problem is solved to the degree that it is possible to use the keyboard etc. again, and the sound volume can be adjusted again with Ubuntu's speaker symbol.
    I guess this must be a driver issue that ubuntu 11.1 does not support the buttons.
    As well, the one-key-theatre button and the thermal-management button do not work. Pressing them, just nothing happens (except that the light up).
    I should mention that installing Ubuntu apparently deleted the partitions including the one-key recovery button. At least this key does now only work like a second power-button. Unfortunately I did not receive the User-guide with the computer but only downloaded from the internet after installing Ubuntu.
    I wonder whether apart from adjusting the volume buttons, it might be possible to get the one-key-theatre button and thermal-management-button operational for ubuntu too, and whether the one-key-recovery button could work under ubuntu too. Gparted tells me that I have 2 small partitions of 3.9 GiB each, labeled "extended" and "windows swap", and one of 1.02 GiB which is not in use apart from the main drive of course.

    The issue you are encountering is due to driver absence in Linux.
    The driver for Linux is not available.  Hope, Ubuntu new version have more applications and drivers.
    Best Regards,
    Tanuj
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution".! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Dual booting Arch and Ubuntu

    Hi, I would like to dual boot Arch and Ubuntu using GRUB2.
    I already have Arch, set up as it's described in the Beginner's Guide, with GRUB2 installed. How would I go about dual booting Ubuntu, preferably without overwriting the existing bootloader?
    I haven't tried anything yet, but the problem that I can see is resizing my /home; is this possible on the Ubuntu liveDVD? If not, would I be able to resize /home with my gParted liveCD?
    Unfortunately, I have no backup media to use, so I wouldn't be able to transfer anything away as a backup.
    Here is my partition table:
    %lsblk
    NAME   MAJ:MIN RM   SIZE       RO TYPE      MOUNTPOINT
    sda      8:0       0        931.5G   0    disk
    ├─sda1   8:1    0        30G        0    part       /
    ├─sda2   8:2    0        12G        0    part       [SWAP]
    ├─sda3   8:3    0        5M          0    part
    └─sda4   8:4    0        889.5G   0    part       /home
    sda1 is my root partition, sda2 is swap, sda3 is GRUB's boot partition, which I was told that I needed in the guide, and sda4 (/home) occupies the "rest of the disk".
    I am using a GPT-partitioned drive, as I read this has many advantages and I do not plan to triple-boot Windows.
    So, can someone tell me what I do if I want to dual boot Ubuntu? I'm very sorry if this should have been posted on the Ubuntu forums, but I'm just more familiar with Arch, and I already have it installed. Please ask if you need any other files like my fstab. I have my Ubuntu liveDVD, GParted live CD (and Arch CD) at hand.
    Thanks in advance, rberyl.
    (Also, does anyone else think it's a bit of a backwards thing to put the output of "date -u +%W$(uname)|sha256sum|sed 's/\W//g'" as a sign-up question? )
    Last edited by rberyl (2012-12-29 11:45:23)

    Hi rberyl,
    You can change your partitions using an inbuilt tool like cfdisk, or if you'd prefer a GUI gparted can be installed from the Arch repos. This will allow you to shrink sda4, and set up the new partitions for your Ubuntu OS. Although this shouldn't cause any data loss, its best practice to back up just in case.
    When installing Ubuntu, be sure to opt-out of bootloader creation. I think you have to use the alternate installation media to get this option. You can add your Ubuntu partition to the existing bootloader by running osprober (available from the repos) and then running grub-mkconfig -o /boot/grub/grub.cfg . Alternatively, you can manually edit your GRUB config. See https://wiki.archlinux.org/index.php/GR … NU.2FLinux for instructions.
    Good luck!
    Last edited by smazza (2012-12-29 16:04:08)

  • Dual booting arch (usb) and ubuntu (grub2)

    Greetings,
    I'm trying to dual boot Arch linux (installed without a bootloader on a USB SSD) and Ubuntu 10.04 (installed on a hdd with GRUB2) but can't get Arch to boot. (Oh and I already have windows dualbooted)
    The entry grub autogenerated:
    menuentry "Arch Linux [/boot/vmlinuz26] (on /dev/sdb3)" {
    insmod ext2
    set root='(hd1,1)'
    search --no-floppy --fs-uuid --set 95d9208a-44e4-48ba-abd2-a365d1ac25ff
    linux /vmlinuz26 root=/dev/sda3 ro
    initrd /kernel26.img
    Why did it input root=/dev/sda3 as it says (on /dev/sdb3)?
    The entry I figured would work:
    menuentry "Arch Linux" {
    set root=(hd1,0)
    linux /boot/vmlinuz26 root=/dev/sdb3 ro
    initrd /boot/kernel26.img
    Output from fdisk -l:
    Disk /dev/sda: 160.0 GB, 160041885696 bytes
    255 heads, 63 sectors/track, 19457 cylinders
    Units = cylinders of 16065 * 512 = 8225280 bytes
    Sector size (logical/physical): 512 bytes / 512 bytes
    I/O size (minimum/optimal): 512 bytes / 512 bytes
    Disk identifier: 0xbc4264d9
    Device Boot Start End Blocks Id System
    /dev/sda1 * 1 13 102400 7 HPFS/NTFS
    Partition 1 does not end on cylinder boundary.
    /dev/sda2 13 5286 42353664 7 HPFS/NTFS
    Partition 2 does not end on cylinder boundary.
    /dev/sda3 5286 19458 113831937 5 Extended
    Partition 3 does not end on cylinder boundary.
    /dev/sda5 18971 19458 3905536 82 Linux swap / Solaris
    /dev/sda6 5286 6502 9764864 83 Linux
    /dev/sda7 6502 18971 100155392 83 Linux
    Partition table entries are not in disk order
    WARNING: GPT (GUID Partition Table) detected on '/dev/sdb'! The util fdisk doesn't support GPT. Use GNU Parted.
    Disk /dev/sdb: 8019 MB, 8019509248 bytes
    255 heads, 63 sectors/track, 974 cylinders
    Units = cylinders of 16065 * 512 = 8225280 bytes
    Sector size (logical/physical): 512 bytes / 512 bytes
    I/O size (minimum/optimal): 512 bytes / 512 bytes
    Disk identifier: 0x00000000
    Device Boot Start End Blocks Id System
    /dev/sdb1 * 1 13 104391 83 Linux
    /dev/sdb2 14 111 787185 82 Linux swap / Solaris
    /dev/sdb3 112 685 4610655 83 Linux
    /dev/sdb4 686 974 2321392+ 83 Linux
    /dev/sdb3 is the root partition
    The content of /dev/sdb1
    grub
    kernel26-fallback.img
    kernel26.img
    lost+found
    System.map26
    vmlinuz26
    - If I try to edit the root=/dev/sda3 to /dev/sdb3 it begins booting but doesnt find /dev/sdb3.
    Thanks in advance for any help,
    Oskar

    Greetings,
    I'm trying to dual boot Arch linux (installed without a bootloader on a USB SSD) and Ubuntu 10.04 (installed on a hdd with GRUB2) but can't get Arch to boot. (Oh and I already have windows dualbooted)
    The entry grub autogenerated:
    menuentry "Arch Linux [/boot/vmlinuz26] (on /dev/sdb3)" {
    insmod ext2
    set root='(hd1,1)'
    search --no-floppy --fs-uuid --set 95d9208a-44e4-48ba-abd2-a365d1ac25ff
    linux /vmlinuz26 root=/dev/sda3 ro
    initrd /kernel26.img
    Why did it input root=/dev/sda3 as it says (on /dev/sdb3)?
    The entry I figured would work:
    menuentry "Arch Linux" {
    set root=(hd1,0)
    linux /boot/vmlinuz26 root=/dev/sdb3 ro
    initrd /boot/kernel26.img
    Output from fdisk -l:
    Disk /dev/sda: 160.0 GB, 160041885696 bytes
    255 heads, 63 sectors/track, 19457 cylinders
    Units = cylinders of 16065 * 512 = 8225280 bytes
    Sector size (logical/physical): 512 bytes / 512 bytes
    I/O size (minimum/optimal): 512 bytes / 512 bytes
    Disk identifier: 0xbc4264d9
    Device Boot Start End Blocks Id System
    /dev/sda1 * 1 13 102400 7 HPFS/NTFS
    Partition 1 does not end on cylinder boundary.
    /dev/sda2 13 5286 42353664 7 HPFS/NTFS
    Partition 2 does not end on cylinder boundary.
    /dev/sda3 5286 19458 113831937 5 Extended
    Partition 3 does not end on cylinder boundary.
    /dev/sda5 18971 19458 3905536 82 Linux swap / Solaris
    /dev/sda6 5286 6502 9764864 83 Linux
    /dev/sda7 6502 18971 100155392 83 Linux
    Partition table entries are not in disk order
    WARNING: GPT (GUID Partition Table) detected on '/dev/sdb'! The util fdisk doesn't support GPT. Use GNU Parted.
    Disk /dev/sdb: 8019 MB, 8019509248 bytes
    255 heads, 63 sectors/track, 974 cylinders
    Units = cylinders of 16065 * 512 = 8225280 bytes
    Sector size (logical/physical): 512 bytes / 512 bytes
    I/O size (minimum/optimal): 512 bytes / 512 bytes
    Disk identifier: 0x00000000
    Device Boot Start End Blocks Id System
    /dev/sdb1 * 1 13 104391 83 Linux
    /dev/sdb2 14 111 787185 82 Linux swap / Solaris
    /dev/sdb3 112 685 4610655 83 Linux
    /dev/sdb4 686 974 2321392+ 83 Linux
    /dev/sdb3 is the root partition
    The content of /dev/sdb1
    grub
    kernel26-fallback.img
    kernel26.img
    lost+found
    System.map26
    vmlinuz26
    - If I try to edit the root=/dev/sda3 to /dev/sdb3 it begins booting but doesnt find /dev/sdb3.
    Thanks in advance for any help,
    Oskar

  • How to install Windows7 and Ubuntu 14.04 on a T440a

    First of all, sorry for my poor English.
    I am a new owner of a Thinkpad T440s which was delivered without an operation system. I want to install Windows 7 and Ubuntu 14.04 for dual boot.
    I am going to install windows first, followed by the installation of ubuntu. - That is the recommended way, isn't it? Which settings are necessary in bios/uefi for that purpose?
    Many thanks in advance for your help.

    Lightning is a problem for you because it hooks into Thunderbird at a low level and you need a version compiled for the platform Thunderbird is running on. So you can't do the preferred solution, which is to put your whole profile in a shared folder and have both instances of Thunderbird reference the same profile. (Ditto for Enigmail). Lightning may become an integral part of Thunderbird in an upcoming release, at which point this limitation due to Lightning should disappear.
    And if you can't use a shared profile, you can't set your Lightning, or your Address Book, to share a common set of files. Put another way, the linkage from Thunderbird to its address book files and calendar data is hard-coded, and not exposed where we can adjust it. :-(
    The halfway house is to place your mail stores in a shared place, and use the Local Directory setting in each account's settings to connect to it. They don't need to be in the profile; what's more important in your case is that they are in a folder accessible to both operating systems.
    Look in your profile; everything under Mail and ImapMail needs to be moved out to a shared folder. Note the entries in Thunderbird under Local Directory before you do this, and reconstruct those pathnames in Thunderbird, but adjusted to suit their new locations.
    (You can see here that you need to make many adjustments, one per account, in each instance of Thunderbird, so it's a high-maintenance solution and this is why we don't recommend it when the alternative, moving the whole profile, is possible.)
    I share address books and calendars between Thunderbirds on various computers (and my phone and tablet) by syncing to something in the cloud; Google Contacts and Google Calendar are my choices, using gContactSync and CalDav.
    Having made the break myself some years ago, I'd recommend you break away from Windows. ;-)

  • 4GB Flash Drive not loading on Mac (but on Windows and Ubuntu)

    Hello,
    I have a 4GB flash drive (probably from LG) that I bought about 3 years ago. It was working just fine all this time but now, all of a sudden, it's gone. Not working, showing up neither in Finder nor in Disk Utility. But it works just fine on Windows 7 and Ubuntu. Files are even readable there. I tried re-formatting it on Ubuntu in FAT-32 but it still won't show up on a Mac.
    Any other flash drive is showing up on my computer (tested with 2 different ones).
    Any clue?

    I don't claim to know the solution to your problem, but in your situation I would try either or both administrator install methods: 1) Right-click the downloaded install file, choose "Run as Administrator" and install the software as usual. 2) Try using a different Windows account that you are positively certain has full administrator rights or the actual Administrator login name, install with that account.
    Also, make sure you empty the browser cache before retrying the http pages. What about other browser settings, like security or privacy settings? Any add-ons or antivirus browser helper objects?
    Do you only use Internet Explorer, or is this issue the same in Firefox, Opera, Chrome and Safari?
    Good luck, hope you get the error fixed.

  • 5130 Connectivity and Ubuntu

    Hi,
    I'm hoping somebody can help me.
    I have been using a Sony Ericsson W900i with my Dell Mini-9 Netbook that runs with Ubuntu 8.04LTS, all I had to do was connect the USB cable to the netbook and handset and Ubuntu saw it as a network connection, was able to browse, send/receive email etc.
    I have just "upgraded" to a Nokia 5130 and it's not working in this way.
    On the Ubuntu forums I did find this:
    connect Nokia to USB & select "PC Suite" mode
    ubuntu@ubuntu:~$ lsusb
    Bus 003 Device 008: ID 0AAA:00BB Nokia Mobile Phones
    ubuntu@ubuntu:~$
    --> vendor id = 0xAAA
    --> device id = 0xBB
    sudo /sbin/modprobe usbserial vendor=0xAAA product=0xBB
    wvdialconf create
    sudo gedit /etc/wvdial.conf
    below adapt Baud & Init3 depending on modem & cell Internet Provider APN
    you can find world APN lists on internet or ask your cell operator
    Phone field maybe adapt too
    [Dialer Defaults]
    Modem = /dev/ttyACM0
    0Baud = 460800
    Init1 = ATZ
    Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
    init3 = AT+CGDCONT=1,"IP","your_APN","",0,0
    ISDN = 0
    Modem Type = Analog Modem
    Phone = *99#
    Username = find it for your APN
    Password = find it for your APN
    Stupid Mode = 1
    then type :
    sudo wvdial
    ubuntu@ubuntu:~$ sudo wvdial
    --> WvDial: Internet dialer version
    --> Modem initialized.
    --> Sending: ATDT*99#
    --> Waiting for carrier.
    ATDT*99#
    CONNECT
    --> local IP address bla.bla.bla.bla
    So I know I can "force" a connection, but it is far from user friendly to do this everytime I want to use the Nokia. I'm looking and rolling out a lot of netbooks and mobile phones to field staff so need to find a solution at present my solution is not to use Nokia

    Thanks for the reply DeepestBlue. Kinda of ironic that Nokia's tag line is "Connecting People" and yet they seem so slow to actually help people get connected, especially when they were involved in an open source project for bluetooth.
    I guess I could create a script and configure sessions in Ubuntu to run it, not a really an ideal solution but thanks for the idea it's an option. My problem is that the field staff will be given the netbooks, which will be configured to run an application when the start up. The vast (95-98%) of the users are non-technical so we have tried to make the system as easy as possible to run, in fact we have removed everything from the desktop and disabled gmone-panel so that they can't accidentally click the wrong thing
    I actually tested a 7310 Supernova last night and had the same problem.

  • Install Oracle 11G, RAC with VMWare, APPS R12, and OBIEE on one server?

    Dear Experts,
    I'm looking to upgrade my skills, and want to learn more of:
    Oracle 11G, RAC, VMWare, APPS R12, and OBIEE
    My server has two quad cores (8 CPU altogether) and 16 gigs of RAM.
    Years ago, I took a shots at installing RAC on multiple servers and firewire.
    One thing I remember was that after I installed RAC, I was not able to use the database unless I enabled all the RAC processes on the server. So, I was not able to just boot the database and use it in the traditional single server manner.
    Which I will also want to do.
    1) Does this symptom/aspect/characteristic of RAC install still exist?
    2) Is it realistic to install all this software on one server?
    If so, what is the order of operations for the install?
    3) If I have to prioritize, I'd like to install
    Oracle 11G, OBIEE, and APPS R12,
    Would installing R12 and OBIEE on the same server present any conflicts or issues?
    If not, what is the order of operations for the install?
    11G, R12, then OBIEE?
    Thanks a lot!

    Hi,
    1) Does this symptom/aspect/characteristic of RAC install still exist?No.
    2) Is it realistic to install all this software on one server?
    If so, what is the order of operations for the install?For learning/traning/demonstration purpose you can Install all these software on same machine.
    3) If I have to prioritize, I'd like to install
    Oracle 11G, OBIEE, and APPS R12,
    Would installing R12 and OBIEE on the same server present any conflicts or issues?
    If not, what is the order of operations for the install?
    11G, R12, then OBIEE?There will not be any conflicts. I would suggest you to select vmware or virtual box in order to configure all these sw's.
    I have done such a configuration on my laptop with i7 Quad processor, 16GB RAM and 640 GB HDD.
    I have Installed 2 node RAC, 2 Node ERP and all are running smoothly without any issues.
    Refer:
    http://appsdbaworkshop.blogspot.com/2011/10/11gr2-rac-on-linux-56-using-vmware.html
    thanks,
    X A H E E R

  • Is there a way to dual-boot OS X and Ubuntu on a PC?

    Recently, my MacBook Pro was stolen along with my book bag while I was at school. The laptop and bookbag have failed to show up and I don't have the money to replace the Mac with a less expensive used or refurbished Mac. So I'm thinking about getting a Lenovo laptop to replace my MacBook Pro. I was wondering is there any way to dual-boot OS X Snow Leopard and Ubuntu on a PC? The Lenovo laptop has Windows 7 installed by default but I will replace it with Linux to dual-boot OS X alongside Ubuntu.
    I was wondering is it possible to run OS X on a non-Mac computer and how would I do this?
    I love using Apple products but it stinks when something like this happens and then I have to rethink the situation and try to find a solution. I'm not abandoning Apple because I'd rather run OS X on a linux computer than Windows, but that's just me.

    OSX is legal only on Apple hardware.  In addition, several who have tried to to load OSX on PC-hardware find the result buggy, or cannot find hardware drivers for the "alien" devices.

  • My external hard drive ejects when copying data. It works on windows and ubuntu. Are there any fixes?

    My external hard drive ejects when copying data. It works on windows and ubuntu. Are there any fixes?

    mine do the same thing... its one of the bugs from the 10.6.8 update

  • Lenovo s12 and Ubuntu 9.10

    Any ideas? I am using the live CD and it doesn't work..

    Hello to all,
    Rather than starting a new topic I decided to hijack this for my questions about S12 ion and Ubuntu.
    I've been using Karmic Koala for a while and then I decided to try Linux Mint Helena, based on the same distro.
    There are a couple of things that I am yet to come over. These are:
    - I run XBMC in Ubuntu, connecting my Leno to an HD LCD via HDMI. Whenever I connect to my tv I have to manually switch to tv out via Leno's hw shortcut and then go to Nvidia settings to adjust the display resolution AND panning. Each time I connect to my tv I have to go thru all these because Nvidia settings won't let me save the configuration. I'd like to know how I can automate this process like in Windows when I connect the hdmi cable the output automatically switches to LCD.
    - Likewise, each time I connect to my tv I have to manually go thru audio settings and select hdmi out. I'd also like to know if there is a way to simplify this.
    - Because XBMC is not compatible with Compiz, I have to go to System>Appearance>Effects and disable Compiz each time I run XBMC. I'd also like to automate this process.
    Other than the above little problems I run into in my daily usage of the netbook, Ubuntu seems to run perfect. Though I have been following Ubuntu since v6 or smt, I can't say that I'm an experienced Linux user but I'd be willing to help as much as I can with your problems. I was lucky to have figured out some of the problems I came across like enabling the unrecognized wireless card, renaming my ntfs partitions and making them auto-mount etc.
    Best regards,
    Haluk

  • Choppy scrolling, both WXP and Ubuntu / sleepy drop-downs

    I use Firefox on both my Windows XP and Ubuntu 11.04 OS's. In both v.9 and now in v.10, I can't get smooth scrolling with my MS Wireless Optical Mouse 2.0. Scrolls fine in all other app's. Problem is worst in Ubuntu, with scrolling so choppy it hurts!
    Also in Ubuntu, when I run the cursor over the drop-down File menus, they often don't drop down, or are very slow to do so. I like FF, but this is marring my web experience!

    Did you close and restart Firefox after disabling hardware acceleration?

  • Triple boot OS X, Vista and Ubuntu

    Is there away to triple boot OS X, Vista and ubuntu without having to use Parallels as i want to use the xgl in ubuntu.
    any help will be good.
    thanks

    http://ubuntuforums.org/showthread.php?t=198453

Maybe you are looking for