Vmware clients not receiving dhcp from wifi networks

we are testing mac laptops running windows 7 virtually using vmware fusion at our office. One problem i ran into is windows 7 cant ever get the dhcp information from Domain Controller to get onto the network/internet here at the office. i have set the NIC to bridged mode in vmware fusion. it works fine at my house where i can get on my home network/internet  just not in the office so i know it can be done, but not sure what setting on the cisco wireless lan controller 2106 controlls that feature. can anyone assist me in resolving this? if i plug it into the network using an ethernet cable everything works just fine, so i believe it is just a setting on the wireless controller that needs to be changed, at least thats what i am hoping, im hoping its not some limitation of the system......

Hi,
I thought i replied to this post.. but i havent.. extremly sorry!! here is the bug that we are hitting!!
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsi90344
There are workarounds to overcome this..
Workarounds: 1. Configure the virtual machine software for NAT ("shared networking")  mode, not bridged mode.    2. If using 4.1 WLC software, configure the virtual machine to use static  IP addressing, not DHCP.   3. If you have an AP that does H-REAP, change the AP mode to H-REAP and local switching so that DHCP (and other) packets do not traverse the controller.
lemme know if this answered your question..
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull

Similar Messages

  • Clients not receiving DHCP IP address from HREAP centrally Switched Guest SSID

    Hi All,
    I am facing a problem in a newly deployed branch site where the Clients are not receiving DHCP IP address from a centrally switched Guest SSID. I see the client status is associated but the policy manager state is in DHCP_REQD.
    The dhcp pool is configured on the controller itself. The local guest clients are able to get DHCP and all works fine, the issue is only with the clients in the remote site. The Hreap APs are in connected mode. Could you please suggest what could be the problem. Below is the out of the debug client.
    *apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 Adding mobile on LWAPP AP 3c:ce:73:6d:37:00(1)
    *apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 Reassociation received from mobile on AP 3c:ce:73:6d:37:00
    *apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 0.0.0.0 START (0) Changing ACL 'Guest-ACL' (ACL ID 0) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1393)
    *apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 Applying site-specific IPv6 override for station 10:40:f3:91:7e:24 - vapId 17, site 'APG-MONZA', interface 'vlan_81'
    *apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 0.0.0.0 START (0) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1393)
    *apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 Applying IPv6 Interface Policy for station 10:40:f3:91:7e:24 - vlan 81, interface id 13, interface 'vlan_81'
    *apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 Applying site-specific override for station 10:40:f3:91:7e:24 - vapId 17, site 'APG-MONZA', interface 'vlan_81'
    *apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 0.0.0.0 START (0) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1393)
    *apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
    *apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state AUTHCHECK (2)
    *apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 0.0.0.0 AUTHCHECK (2) Change state to L2AUTHCOMPLETE (4) last state L2AUTHCOMPLETE (4)
    *apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 3c:ce:73:6d:37:00 vapId 17 apVapId 1
    *apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state DHCP_REQD (7)
    *apfMsConnTask_3: May 24 13:26:49.372: 10:40:f3:91:7e:24 apfMsAssoStateInc
    *apfMsConnTask_3: May 24 13:26:49.373: 10:40:f3:91:7e:24 apfPemAddUser2 (apf_policy.c:222) Changing state for mobile 10:40:f3:91:7e:24 on AP 3c:ce:73:6d:37:00 from Idle to Associated
    *apfMsConnTask_3: May 24 13:26:49.373: 10:40:f3:91:7e:24 Scheduling deletion of Mobile Station:  (callerId: 49) in 28800 seconds
    *apfMsConnTask_3: May 24 13:26:49.373: 10:40:f3:91:7e:24 Sending Assoc Response to station on BSSID 3c:ce:73:6d:37:00 (status 0) ApVapId 1 Slot 1
    *apfMsConnTask_3: May 24 13:26:49.373: 10:40:f3:91:7e:24 apfProcessAssocReq (apf_80211.c:4672) Changing state for mobile 10:40:f3:91:7e:24 on AP 3c:ce:73:6d:37:00 from Associated to Associated
    *apfReceiveTask: May 24 13:26:49.373: 10:40:f3:91:7e:24 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
    *apfReceiveTask: May 24 13:26:49.373: 10:40:f3:91:7e:24 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 4183, Adding TMP rule
    *apfReceiveTask: May 24 11:35:53.373: 10:40:f3:91:7e:24 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
      type = Airespace AP - Learn IP address
      on AP 3c:ce:73:6d:37:00, slot 1, interface = 13, QOS = 3
      ACL Id = 255, Jumbo F
    *apfReceiveTask: May 24 13:26:49.373: 10:40:f3:91:7e:24 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 7006  IPv6 Vlan = 81, IPv6 intf id = 13
    *apfReceiveTask: May 24 13:26:49.373: 10:40:f3:91:7e:24 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (ACL ID 255)
    *pemReceiveTask: May 24 13:26:49.373: 10:40:f3:91:7e:24 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
    *pemReceiveTask: May 24 13:26:49.373: 10:40:f3:91:7e:24 Sent an XID frame
    *apfMsConnTask_3: May 24 13:26:49.401: 10:40:f3:91:7e:24 Updating AID for REAP AP Client 3c:ce:73:6d:37:00 - AID ===> 1
    *apfReceiveTask: May 24 13:28:49.315: 10:40:f3:91:7e:24 0.0.0.0 DHCP_REQD (7) DHCP Policy timeout
    *apfReceiveTask: May 24 13:28:49.315: 10:40:f3:91:7e:24 0.0.0.0 DHCP_REQD (7) Pem timed out, Try to delete client in 10 secs.
    *apfReceiveTask: May 24 13:28:49.315: 10:40:f3:91:7e:24 Scheduling deletion of Mobile Station:  (callerId: 12) in 10 seconds
    *osapiBsnTimer: May 24 13:28:59.315: 10:40:f3:91:7e:24 apfMsExpireCallback (apf_ms.c:599) Expiring Mobile!
    *apfReceiveTask: May 24 13:28:59.315: 10:40:f3:91:7e:24 apfMsExpireMobileStation (apf_ms.c:4897) Changing state for mobile 10:40:f3:91:7e:24 on AP 3c:ce:73:6d:37:00 from Associated to Disassociated
    *apfReceiveTask: May 24 13:28:59.315: 10:40:f3:91:7e:24 Scheduling deletion of Mobile Station:  (callerId: 45) in 10 seconds
    *osapiBsnTimer: May 24 13:29:09.315: 10:40:f3:91:7e:24 apfMsExpireCallback (apf_ms.c:599) Expiring Mobile!
    *apfReceiveTask: May 24 13:29:09.316: 10:40:f3:91:7e:24 Sent Deauthenticate to mobile on BSSID 3c:ce:73:6d:37:00 slot 1(caller apf_ms.c:4981)
    *apfReceiveTask: May 24 13:29:09.316: 10:40:f3:91:7e:24 apfMsAssoStateDec
    *apfReceiveTask: May 24 13:29:09.316: 10:40:f3:91:7e:24 apfMsExpireMobileStation (apf_ms.c:5018) Changing state for mobile 10:40:f3:91:7e:24 on AP 3c:ce:73:6d:37:00 from Disassociated to Idle
    *apfReceiveTask: May 24 13:29:09.316: 10:40:f3:91:7e:24 0.0.0.0 DHCP_REQD (7) Deleted mobile LWAPP rule on AP [3c:ce:73:6d:37:00]
    *apfReceiveTask: May 24 13:29:09.316: 10:40:f3:91:7e:24 Deleting mobile on AP 3c:ce:73:6d:37:00(1)
    *pemReceiveTask: May 24 13:29:09.317: 10:40:f3:91:7e:24 0.0.0.0 Removed NPU entry.

    #does the client at the remote site roams between AP that connects to different WLC?
    #type 9 is not good.
    *pemReceiveTask: May 24 13:26:49.373: 10:40:f3:91:7e:24 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
    #Does your dhcp server getting hits.
    #Also, get debug dhcp message & packet.
    #Dhcp server is not responding.
    *apfReceiveTask: May 24 13:28:49.315: 10:40:f3:91:7e:24 0.0.0.0 DHCP_REQD (7) DHCP Policy timeout
    *apfReceiveTask: May 24 13:28:49.315: 10:40:f3:91:7e:24 0.0.0.0 DHCP_REQD (7) Pem timed out, Try to delete client in 10 secs.

  • Clients not getting DHCP from external server

    Hi,
    I have a 4402 (version 7.0.235) working with 10 units of 1121 APs connected to it. The WLC is not configured to work in LAG mode. Physical portt #1 is connected to the Main Switch (trunk). I have 3 WLAN mapped to 3 Different VLAN and Everything (security and internal, external DHCP) is working swell...
    Now- I have connected Physical port #2 directly to an ADSL Router (giga port), Configured Port 2 as untaggedwith the proper IP details.
    I have configured this interface to receive DHCP from the ADSL Router and for some reason, Clients are not getting addresses.
    When I assign a Static address to my laptop I get internet access and all is nice. I tried configuring The WLC internal DHCP server (instead of the ADSL router) and that didn't help. It seems like a DHCP problem but I dont understand the source of the problem of think of the solution.
    When turning off the proxy settings I noticed that it helped. Is there anything to do with that? The problem was that after a while the other WLANs starting causing DHCP issues as well.
    What is supposed to be configured? Any Expert is the House?
    I attached a crappy drawing..

    Hi Scott,
    Thanks for your answer.
    So what you are basicly saying is that I have 2 choices: 1 - disable the Proxy option on the WLC and work with external DHCP servers (internal will not work when this is enabled). 2 - Enable the Proxy option and only work with the WLC internal DHCP.
    I have installed many WLCs this way, having Different DHCP Servers (external and internal)  for multiple WLANs.
    What do you think may be different this time? The router that I am using isn't the most expencive but it is providing DHCP to other clients (wired client) with no problems.
    Thanks!!!

  • Clients not receiving addresses from DHCP

    I have a Cisco 2811 router and have configured it to be a DHCP server at a remote site.  It seems like it should be pretty straight forward to configure DHCP.  Apparently I'm missing something because I can't get clients to receive an address.  Below are the applicable parts of the config.  I also have tried associating the DHCP pool with the Claims vrf and that did not work either.
    ip dhcp excluded-address 10.10.30.0 10.10.30.99
    ip dhcp excluded-address 10.10.30.201 10.10.30.255
    ip dhcp pool Claims_Office
       network 10.10.30.0 255.255.255.0
       domain-name fmi.com
       default-router 10.10.30.253
       dns-server 10.10.10.191
       lease 7
    interface FastEthernet0/0
    description Claims Office
    vrf forwarding Claims
    ip address 10.10.30.253 255.255.255.0
    duplex auto
    speed auto
    no mop enabled
    interface FastEthernet0/0/0.1205
    description Claims Office
    vrf forwarding Claims
    encapsulation dot1Q 1205
    ip address 192.168.103.2 255.255.255.252

    Unfortunately that didn't work.  Here is the output before:
    Pool Claims_Office :
     Utilization mark (high/low)    : 100 / 0
     Subnet size (first/next)       : 0 / 0
     Total addresses                : 254
     Leased addresses               : 0
     Pending event                  : none
     1 subnet is currently in the pool :
     Current index        IP address range                    Leased addresses
     10.10.30.1           10.10.30.1       - 10.10.30.254      0
    And after:
    Pool Claims_Office :
     Utilization mark (high/low)    : 100 / 0
     Subnet size (first/next)       : 0 / 0
     Total addresses                : 254
     Leased addresses               : 0
     Pending event                  : none
     1 subnet is currently in the pool :
     Current index        IP address range                    Leased addresses
     10.10.30.1           10.10.30.1       - 10.10.30.254      0
    What I want is for it to assign addresses from 10.10.30.100-199

  • WLC2504 clients not receiving DHCP leases

    I'm stock with a 2504 using version 7.0.220.0 that won't lease out DHCP adresses
    Wifi clients are unable to get a DHCP lease from an external DHCP server.
    The WLC are handling 3 WLAN, 2 using internal DHCP server, 1 (that wont work) using external DHCP. The external DHCP server, is a router/firewall (out of my reach) that suffered from a power out, a short while ago, ever since the DHCP is not working on that VLAN, if client are getting static ip adresses, everything works fine. If i'm using the same network link, and plug it into a computer, I get a DHCP address.
    I've enable DHCP proxy
    Debbuging DHCP, using: Debug DHCP packets enable
    Gives me this:
    *DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP received op BOOTREQUEST (1) (len 308,vlan 20, port 1, encap 0xec00)
    *DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP option len (including the magic cookie) 72
    *DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP option: message type = DHCP INFORM
    *DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP option: 61 (len 7) - skipping
    *DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP option: 12 (len 1) - skipping
    *DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP option: vendor class id = MSFT 5.0 (len 8)
    *DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP option: 55 (len 13) - skipping
    *DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP options end, len 72, actual 64
    *DHCP Socket Task: Nov 08 14:21:11.397: c8:0a:a9:cc:6d:f6 DHCP dropping packet (no mscb) found - (giaddr 0.0.0.0, pktInfo->srcPort 68, op: 'BOOTREQUEST')
    Thanks

    Hi Steen,
    When a client is in DHCP REQ state on the controller, the controller drops DHCP inform packets. The client will not go into a RUN state on the controller (this is required for the client to pass traffic) until it receives a DHCP discover packet from the client. DHCP inform packets are forwarded by the controller when DHCP proxy is disabled.
    Please check this, if still u r facing issue then provide more info.
    Can you please paste a client debug of the client having DHCP issues.
    Go to cli of the wlc and run the client debug . Diconnect  the client then reconnect and gather the output and post.
    Regards

  • Simple contact form Client not receiving email from test site

    I have entered my client's verified email, cut and pasted it into place. I have added my email and my wifes email. The only person not getting the forms email info is my client. I'm baffled.

    The URL for the site is getthenetbassguide com.businesscatalyst.com/index.html. I have added several peoples email address', including my own to the back end of the form. As I've said the only person not receiving emails is my client who opened an account with 1 and 1. I contacted 1 and 1. They show no spam filters on their end so I'm still baffled. I asked about firewall permissions and they were not helpful. Is there a way to monitor the email and see what could be blocking it?
    Owen Moore
    Moore Designs
    847-732-1318
    [email protected]
    Freshbrewedart.com
    Sent from my iPhone

  • IOS mail client not working in certain wifi networks

    Hey,
    this is driving me crazy:
    When I use my iPad or iPhone within our universities eduroam wifi network, receiving and sending mails does not work.
    I am using a google apps account. One would say, ok that's due to some IMAP and SMTP port blocking. However it isn't. Using my android phone with the same settings it just wouldn't work ... Never!
    Using my iPad in other networks works just fine ...
    Please help me with some suggestions.
    Jacob

    It could be the network, but what surprises me is that nothing else is being blocked at all. And I can't seem to change the port that Mail is on. I tried a port scan, and it came up that that port is blocked (993), but it also came up that every other port I tried was also blocked. I used a Mac to do a Port Scan for my iPad's IP, but it wasn't detecting any open ports. So I don't know if it is an issue with the network, or perhaps with my iOS devices. The network has 802.1X security I believe (I need a username and password to login), so unsure if this would affect it at all?

  • Airport Express not receiving DHCP from Ethernet

    Hello All,
    Recently, one of my Airport Express 802.11n access points started using the self assigned IP address 169.254.238.166. While troubleshooting, I have found that this device will receive an IPv4 address when I connect it's Ethernet interface to my D-Link DG-S1248T, but not when I connect it to my Linksys SE2500 (the one it was connected to for over a year before starting this behavior). Ordinarily, I would suspect that something is preventing the Linksys from switching DHCP packets correctly to the Airport Express, but I can assure you the Linksys is sending DHCP packets because I am starting this thread from a Mac Pro connected to that Linksys, with a valid IPv4 address, and wireshark is showing bootps request and reply. I'm using bridged mode on the Airport Express, because I already have a gateway as my DHCP server with NAT, and created a wireless network with firmware version 7.5.2. I even setup another Airport Express 802.11n right next to the faulty one, same config (except the ID), same switch, and it works fine. I also swapped Ethernet patch cables on the Airport Express 802.11n Ethernet interfaces. The green LED access point went back to green when the cables were swapped, while the blinking amber access point stayed blinking amber. Therefore I believe the problem is localized on the faulty Aiport Express 802.11n. Has anyone else seen this fault? What is the root cause, and how did you repair the issue?
    Thanks!

    The Airport Express was functioning normally as recently as last Thursday, when I unplugged it to move. I took care in transporting it so there was definitely no chance of physical damage.
    You mean that it was functioning normally when it was connected to a cable modem last Thursday. Everything has changed. Unfortunately, the Express is known to sometimes have problems after it has been plugged in for a long time, is unplugged, and then started up again. On average, I lose an AirPort Express about once a year this way.
    Power up the Express for a few moments
    Hold in the reset button for 8-10 seconds and release
    Allow a full minute for the Express to restart to a slow, blinking amber light
    Connect the Ethernet cable from wall jack to the WAN "O" port on the Express
    On the Mac, open Macintosh HD > Applications > Utilities > AirPort Utilities
    Click on Other WiFi Devices
    Click on AirPort Express
    The utility will suggest a setup that looks similar to this, except you will see a different picture of the AirPort Express
    Network Name = Name that you want to call your wireless network. Keep it very simple.
    Base Statation = Name that you want to call the AirPort Express device
    Password = Password that will be used for both the wireless and device
    Verify Password
    Click Next
    The utility will setup everything for you. When you see the message of Setup Complete, click Done
    Check the network

  • 10.5.6 setup on mini with USB nic, not receiving DHCP from WAN (cable modem

    Hello,
    I'm probably in a little over my head thinking I could configure MacOS X Server without much IT knowledge. But I started, so I'm not giving up yet.
    Here's my setup:
    — cable modem ethernet connects to USB nic (the apple macbook air one) plugged into mac mini running 10.5.6 Server
    — ethernet on mac mini connects to switch
    — switch connects to airport base station set-up as bridge
    — in the future other computers will connect over ethernet to the switch (that's why mac mini isn't plugged into base station directly)
    Here's the issue:
    — cable modem uses DHCP (no fixed IP).
    — when first installing 10.5.6 Server, modem was connected directly to ethernet on mac mini, and picked up everything from DHCP, worked fine. Ran all the system updates (started with a 10.5 initial install)
    — after everything was installed, I switched the modem to the USB ethernet adapter and ran NAT setup assistant. configured the USB Ethernet as the WAN, Ethernet as the LAN, turned on VPN.
    — now the USB Ethernet won't pick up the DHCP of the WAN anymore. It did it once, and then never again.
    — I've run the NAT setup assistant to switch the WAN and LAN nics to see if the USB Ethernet was the issue, but with the same results.
    — This setup used to work although not quite stable on 10.5.4 server.
    My initial questions:
    — is the firewall blocking the DHCP?
    — is the LAN DHCP messing with the WAN?
    — in the previous version I had to set the replythresholdseconds from 10 to 0 in the bootpd.plist for it to hand out DHCP on the LAN, but there is no such entry in the pootpd.plist anylonger, and the keynet_address entry that was missing from the previous version of bootpd.plist is now present, so it seems the bootpd.plist has been fixed by apple.
    — what am I doing wrong? Why doesn't this just work as advertised...
    I know there are several of you out there that have the same setup working (I found posts from hirstey and DigiAngel with the same setup) so it must be possible. All your help is much appreciated!!
    Thanks,
    Hagenaer
    Thanks!
    Message was edited by: Hagenaer

    Thanks for your reply, DigiAngel.
    DSL modems differ from cable modems as far as I understand. Where DSL modems are actually routers capable of NAT/DHCP, cable modems are just a network interface/brigde and can't do any of that. So it should pass the external IP to the computer. I'm writing on a laptop with the cable modem directly plugged into it, and it picked up the external IP etc. near instantly. The mac mini did the same before I ran the NAT setup assistant. I believe it picked it up once after that, but never since.
    I had done a clean install, had the ethernet plugged into its internal ethernet port (en0) and was able to download all the system updates. Then plugged in the USB ethernet, I'm pretty sure it still picked up the IP there. Ran the NAT setup assistant and can't get anything to work anymore. Even with all services switched off.
    So the modem is doing its job, but when I connect it to the USB nic the connection gets a self-assigned IP in about 3 seconds after seeing the cable is connected. The one time I've seen it get the right IP, it got a self-assigned IP first and then about 5 seconds later picked up on the correct IP. (And it picked up everything, including DNS server and search domains, which this laptop I'm writing on does not, although it works just the same).
    Unfortunately, this laptop runs 10.4.11 which doesn't recognize the USB nic, so I can't test the adapter outside of the server environment. But I've had the genius bar test the adapter previously and it worked fine then, plus I've run the NAT setup assistant with the connections inverted (WAN over built-in ethernet, LAN over USB ethernet) with the same results: WAN gets self-assigned IP.
    I've also tried configuring manual IP for the WAN from what I saw was given to this laptop (it kept the same IP even after being disconnected/reconnected, so I guess the IP for my modem won't change IP unless I reset it. Although I'm not sure if it's correct logic to assume the mac mini would pick up the same IP as well since I think that's actually tied to the MAC address and the IP doesn't belong to the modem but to the computer behind it).
    Anyway, I'm not sure what to try next...
    Hm. Wait, this might have something to do with it: the firewall logs the following:
    Mar 22 14:12:07 server ipfw[4997]: 65534 Deny UDP 73.227.220.1:67 255.255.255.255:68 in via en 2
    Looking up 73.227.220.1 gives me dns1.inflow.pa.bo.comcast.net, clearly my provider's DNS server. Trying to get me an IP that my wirewall is denying? Turning off the firewall doesn't make it pick up the correct IP though... I have turned off all services and still just got a self-assigned IP.

  • WLC2412-Clients Not receiving DHCP addresses

    I recently upgraded a clients WLC and they keep saying they are unable to get an IP address from the DHCP server.  It's a simple, flat network and here is what the logs are showing.  Any advice would be greatly appreciated.
    *apfReceiveTask: Apr 11 13:37:25.477: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
    *apfReceiveTask: Apr 11 13:37:17.278: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
    *apfReceiveTask: Apr 11 13:37:05.880: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
    *apfReceiveTask: Apr 11 13:13:47.397: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
    *apfReceiveTask: Apr 11 13:37:25.477: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
    *apfReceiveTask: Apr 11 13:37:17.278: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
    *apfReceiveTask: Apr 11 13:37:05.880: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
    *apfReceiveTask: Apr 11 13:13:47.397: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.

    (Cisco Controller) show>interface detailed management
    Interface Name................................... management
    MAC Address...................................... 64:00:f1:91:5d:40
    IP Address....................................... 192.168.8.3
    IP Netmask....................................... 255.255.255.0
    IP Gateway....................................... 192.168.8.1
    External NAT IP State............................ Disabled
    External NAT IP Address.......................... 0.0.0.0
    VLAN............................................. 8
    Quarantine-vlan.................................. 0
    Physical Port.................................... 1
    Primary DHCP Server.............................. 192.168.8.49
    Secondary DHCP Server............................ Unconfigured
    DHCP Option 82................................... Disabled
    ACL.............................................. Unconfigured
    AP Manager....................................... No
    Guest Interface.................................. No
    L2 Multicast..................................... Enabled

  • Clients not receiving DHCP on layer 2 Vlan

    I have flexconnect WAPs with local switching and local dhcp server on the switch.
    I have one SSID assigned to a layer 2 vlan.  The wireless clients are unable to receive an ip address on this vlan.  The wired clients are able to receive an ip address on this vlan with no problem.
    The WAP switchport is trunked and all of the layer 3 vlans are working with no problem.
    The layer 2 vlan interface is assign the DHCP -  ip address pool Vendor_VLan
    Any help would be appreciated.
    Thanks
    LH

    Hi LH,
    Have you configured the SSID with "Local Switching" feature. 
    Also did you do the vlan mapping on this FlexConnect AP for the configured SSID ?
    HTH
    Rasika
    **** Pls rate all useful responses ****

  • Not receiving texts from iPhone contacts when I'm not connected to wifi or cell data. I can't send and receive regular SMS texts with non iMessage users but iMessage users message are not being converted to text when I don't have internet connect

    I can send and receive to any non iPhone user. I can send a message as a text to an iPhone user but if I'm not connected to cellular data or wifi I do not receive messages from iPhone contacts. From what I understand these message should automatically send to me as texts instead of iMessages but since the update it's not functioning properly. Please help. I've tried turning iMessage off and I still don't receive the messages until after I reconnect to wifi.

    I have the same problem! Before the upgrade, if I wasn't connected to the internet, any messages sent to me from an iphone would convert automatically to a text message. I have payg tarriff, so I turn cell data off, as it costs too much to use it. I have wifi at home and work, but if I'm out and about, I don't receive texts from iphone users until I'm on wifi. I get them ok from non iphone users. There was never any problem until ios7

  • Not receiving emails from certain people/clients?

    Hi like the tiltle says, i'm not receiving emails from certain clients.
    it doesnt even go into spams, there is no trace at all... like it was never sent
    this makes me worries about how many other emails i've never received
    this particular domain is a domain that i own, and hosted on a dedicated server (i'm the one sending the emails)  i was doing tests before moving that specific site to BC.
    i've tested with a bunch of other accounts that i own and i'm receiving them no problem on my gmail account, and other accounnt that i have on a dedicated server)
    But from that specific domain ie: thatdomain.com i'm am not receiving anything in any accounts of my partner domain.
    where should i look?
    help
    Doesnt help me loving BC, i'v been having a bunch of deceptions ever since i "made the big move"

    Just FYI, everyone here is just a fellow user. .Mac employees provide no technical support here and probably never read any of these posts. If you want to contact .Mac support, you need to fill out and submit the form on this web page. When you fill out the form, provide as much detail as possible - the most important items will be the domain(s) (i.e. someplace.com) that the problem emails are being sent from.
    Good luck.

  • Not receiving texts from a Galaxy 4 mini on US Cellular provider network, but I get all other texts.

    I am not receiving texts from a friend who owns a Galaxy 4 mini on US Cellular provider network, but I receive all other texts from other phones and other providers. She has never owned any Apple products, including an Apple iPhone. Other people she texts with receive her texts fine.
    Any ideas what might be causing this? 

        Hi xg33kx,
    That is definitely an unusual situation. I'm sure it's frustrating that it isn't working when you need it. Do either of you have trouble with texting anyone else? Try turning off Wi-Fi on both devices, and see if the problem persists or continues when using only the mobile network. Please keep us updated with this situation so we can help to resolve!
    Thank you,
    MichelleH_VZW
    Follow us on Twitter @VZWSupport

  • [TroubleShooting]Continuity Wi-Fi issue. iPhone and mac not on the same wifi network

    Ive been following this and other forums since Yosemite came out few weeks back & i can see many other people are having this issue as well.
    The issue is that I'm not able to make/receive calls on my MBP using my iPhone via continuity.
    Ive tried all of the possible solutions made here and elsewhere on how to resolve this issue. [playing about with settings and iCloud]
    When I'm at home all of the handoff and continuity features work apart from making and receiving calls. Tells me my mac and iPhone are not on the same wifi network, even though they are.
    Now, the solution?
    Now this is where tourbleshooting comes in. Ive taken my mac and to my homegirls house & all of the features worked including phonecalls, without changing anything, except?? THE ISP and the router at her house.
    Personally i live in London, Uk. At home i have sky, and my girl has TalkTalk.
    So im 99.9% sure this has nothing to do with the OS X, but rather its the ISP or the router.
    Now I'm asking for help from anyone that understands the ISP's and routers, on what kind of issue there might be. Im no computer wiz kid, but I'm guessing it could be something that has to do with the NAT type. (Call of duty on ps3 haha) At my house its moderate and my homegirls - open? could that be the issue? if so are there any router settings i can play about to see if that solves the issue?
    Thanks.
    Please only post if you know what you're talking about because i don't want anyone giving me some next instructions for my router so i end up without internet what so ever haha And whoever is having the same problem, id appreciate if you'd post on this to keep the post alive

    Hey chrisfromdc,
    If you are having an issue with your Mac being unregistered with iMessage and FaceTime, I would suggest that you troubleshoot using the steps in this article - 
    If you have difficulty activating FaceTime or iMessage - Apple Support
    Thanks for using Apple Support Communities.
    Be well,
    Brett L 

Maybe you are looking for

  • Login page not showing "Unable to generate forwarding URL. Exception:"

    Dear All, I have install the EBS R12 on RHEL 5.5 64bit. All run fine some days but one day after restart there is a issue on database we rectify that DB issue but after that we are not able to get the login page. ALL application/DB node process are e

  • Unable to copy and paste a phote from my photo library to another photo album

    iphoto 6.0.6 unable to copy and paste a photo from my main library album to another photo album.  why does the copy and paste function not work for these albums.  I have tried to drag it and drop it into the album, but nothing works.  it this a bug? 

  • Help me in creatin an index for inequality operator  =

    Hi Gurus, I created an index as below create index bu_eff_from_dt_indx on bu(eff_from_dt) When I got the execution plan as below for this query select * from bu where eff_from_dt = '01-MAR-2006' | Id | Operation | Name | Rows | Bytes | Cost (%CPU)| T

  • Buying iPhone 5 from third party retailer w/ unlimited data

    I ordered an iPhone 5 in-store on the 21st since I couldn't find a way to pre-order and keep my unlimited data, even though I was paying full retail. My ship date isn't until October 19th, and that's a long time to wait. But I did find a local Radios

  • Differences in field IAKOSIST in MCIZ and in MCI8

    Hello! Through tx IFCU I have posted 5 documents, 50 L each one. 1,3 u20AC/L, so every time I filled 50L, IAKOSIST was adding 65u20AC After 5 documents posted, total is 325u20AC=65u20AC*5 This is the value of IAKOSIST is 325u20AC. I see in MCI8 and i