Voice card not appaering in configuration?

we have inserted pvdm3 module in to the 2901 router
but its LED status is showing Amber continuolsly.
I would like configure the VIC3-2FXS/DID card but I am not able to see the card in running configuration but I could see the card in sh diag.
Can any ony help?
Its sh diag command giving the following output.
/#sh diag
Slot 0:
        C2901 Mother board 2GE, integrated VPN and 4W Port adapter, 4 ports
        Port adapter is analyzed
        Port adapter insertion time 00:58:11 ago
        EEPROM contents at hardware discovery:
        PCB Serial Number        : FOC16310CSA
        Hardware Revision        : 1.0
        Part Number              : 73-11834-09
        Top Assy. Part Number    : 800-30795-05
        Board Revision           : A0
        Deviation Number         : 0
        Fab Version              : 03
        Product (FRU) Number     : CISCO2901/K9
        Version Identifier       : V05
        CLEI Code                : CMMHB10ARA
        Processor type           : C1
        Chassis Serial Number    : FGL16312126
        Chassis MAC Address      : 6073.5c26.7440
        MAC Address block size   : 72
        Manufacturing Test Data : 00 00 00 00 00 00 00 00
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF C1 8B 46 4F 43 31 36 33 31 30 43 53 41 40
          0x10: 06 17 41 01 00 82 49 2E 3A 09 C0 46 03 20 00 78
          0x20: 4B 05 42 41 30 88 00 00 00 00 02 03 CB 8C 43 49
          0x30: 53 43 4F 32 39 30 31 2F 4B 39 89 56 30 35 20 D9
          0x40: 04 40 C1 CB C2 C6 8A 43 4D 4D 48 42 31 30 41 52
          0x50: 41 09 C1 C2 8B 46 47 4C 31 36 33 31 32 31 32 36
          0x60: C3 06 60 73 5C 26 74 40 43 00 48 C4 08 00 00 00
          0x70: 00 00 00 00 00 F3 00 65 40 01 25 41 00 87 42 00
          0x80: 00 F8 00 28 03 E8 1C 89 07 D0 20 21 0B B8 20 93
          0x90: 0F A0 21 2F 13 88 21 83 17 70 21 A8 1B 58 21 B0
          0xA0: 1F 40 21 AB 23 28 21 79 27 10 21 78 41 01 1D 42
          0xB0: 00 00 F8 00 28 03 E8 1C 20 07 D0 1F 40 0B B8 20
          0xC0: 6C 0F A0 21 34 13 88 21 34 17 70 21 98 1B 58 21
          0xD0: 98 1F 40 21 98 23 28 21 34 27 10 21 34 FF FF FF
          0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
        PVDM Slot 1:
        16-channel (G.711) Voice/Fax PVDM3 DSP DIMM PVDM daughter card
        Hardware Revision        : 1.0
        Part Number              : 73-11576-03
        Board Revision           : C0
        Deviation Number         : 0
        Fab Version              : 03
        PCB Serial Number        : FOC162257KD
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Processor type           : 00
        Product (FRU) Number     : PVDM3-16
        Version Identifier       : V01
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 05 D8 41 01 00 82 49 2D 38 03 42 43 30
          0x10: 88 00 00 00 00 02 03 C1 8B 46 4F 43 31 36 32 32
          0x20: 35 37 4B 44 03 00 81 00 00 00 00 04 00 09 00 CB
          0x30: 8F 50 56 44 4D 33 2D 31 36 20 20 20 20 20 20 20
          0x40: 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF FF FF
          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
        WIC Slot 0:
        3rd generation - FXS DID Voice daughter card (2 port)
        Hardware Revision        : 1.0
        Top Assy. Part Number    : 800-30501-02
        Board Revision           : A0
        Deviation Number         : 0
        Fab Version              : 07
        PCB Serial Number        : FOC1350420M
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Product (FRU) Number     : VIC3-2FXS/DID
        Version Identifier       : V02
        CLEI Code                : IP9IAB3CAB
        Longitudinal Calibration : 01 10 10 4F 8D 10 10 8F
                                   9F
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 06 21 41 01 00 C0 46 03 20 00 77 25 02
          0x10: 42 41 30 88 00 00 00 00 02 07 C1 8B 46 4F 43 31
          0x20: 33 35 30 34 32 30 4D 03 00 81 00 00 00 00 04 00
          0x30: CB 8D 56 49 43 33 2D 32 46 58 53 2F 44 49 44 89
          0x40: 56 30 32 20 D9 02 40 C1 C6 8A 49 50 39 49 41 42
          0x50: 33 43 41 42 D3 09 01 10 10 4F 8D 10 10 8F 9F FF
          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Embedded Service Engine 0/0 :
Total platform memory : 524288K bytes
Total 2nd core memory : 0K bytes
Start of physical address for 2nd core : 0x80000000
Virtual address start of 2nd core memory : 0x0 - 0x0
2nd core configured disabled
L2 cache ways for 2nd core : 0
Its sh running-conf command giving the following output.
/#sh running-config
Building configuration...
Current configuration : 1228 bytes
! Last configuration change at 06:29:29 UTC Fri Feb 7 2014
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname /
boot-start-marker
boot-end-marker
enable secret 4 tnhtc92DXBhelxjYk8LWJrPV36S2i4ntXrpb4RFmfqY
no aaa new-model
no ipv6 cef
ip source-route
ip cef
multilink bundle-name authenticated
crypto pki token default removal timeout 0
license udi pid CISCO2901/K9 sn FGL16312126
hw-module pvdm 0/1
username cisco
interface Embedded-Service-Engine0/0
no ip address
no ip route-cache
shutdown
interface GigabitEthernet0/0
ip address 172.169.2.152 255.255.255.0
duplex auto
speed auto
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
ip forward-protocol nd
no ip http server
no ip http secure-server
control-plane
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
password cisco
login
transport input all
line vty 5 15
password cisco
login
transport input all
scheduler allocate 20000 1000
end
and sh flash giving me the following output.
/#sh flash
-#- --length-- -----date/time------ path
1     74503236 Jul 30 2012 20:08:54 +00:00 c2900-universalk9-mz.SPA.151-4.M4.bin
2         2903 Jul 30 2012 20:21:54 +00:00 cpconfig-29xx.cfg
3      3000320 Jul 30 2012 20:22:10 +00:00 cpexpress.tar
4         1038 Jul 30 2012 20:22:18 +00:00 home.shtml
5       122880 Jul 30 2012 20:22:26 +00:00 home.tar
6      1697952 Jul 30 2012 20:22:40 +00:00 securedesktop-ios-3.1.1.45-k9.pkg
7       415956 Jul 30 2012 20:22:54 +00:00 sslclient-win-1.1.4.176.pkg

Thank you Gergely Szabo,
Sh Inv output and sh version output is as follows.
/#sh inv
NAME: "CISCO2901/K9 chassis", DESCR: "CISCO2901/K9 chassis"
PID: CISCO2901/K9      , VID: V05 , SN: FGL16312126
NAME: "3rd generation two port FXS DID voice interface daughtercard on Slot 0 SubSlot 0", DESCR: "3rd generation two port FXS DID voice interface daughterca"
PID: VIC3-2FXS/DID     , VID: V02 , SN: FOC1350420M
NAME: "PVDM3 DSP DIMM with 16 Channels on Slot 0 SubSlot 5", DESCR: "PVDM3 DSP DIMM with 16 Channels"
PID: PVDM3-16          , VID: V01 , SN: FOC162257KD
NAME: "C1941/C2901 AC Power Supply", DESCR: "C1941/C2901 AC Power Supply"
PID: PWR-1941-2901-AC , VID:    , SN:
/#show version
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 20-Mar-12 18:57 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)
/ uptime is 3 hours, 22 minutes
System returned to ROM by power-on
System restarted at 08:40:55 UTC Mon Feb 10 2014
System image file is "flash0:c2900-universalk9-mz.SPA.151-4.M4.bin"
Last reload type: Normal Reload
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco CISCO2901/K9 (revision 1.0) with 483328K/40960K bytes of memory.
Processor board ID FGL16312126
2 Gigabit Ethernet interfaces
1 terminal line
2 Voice FXS interfaces
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
Device#   PID                   SN
*0        CISCO2901/K9          FGL16312126
Technology Package License Information for Module:'c2900'
Technology    Technology-package           Technology-package
              Current       Type           Next reboot
ipbase        ipbasek9      Permanent      ipbasek9
security      None          None           None
uc            None          None           None
data          None          None           None
Configuration register is 0x2012

Similar Messages

Voice card not initializing

I have recently got a router - 1751v
and also a voice card - vip2-2fxs
The card is not getting initialized
error showing card not initializing, unknown hardware found in slot1.
is there any patch for the card to be initialized
pls reply

Hi Amit,
Thank you for ur response
here is the sh tech support details of the router
the card is vic-2fxs
------------------ show version ------------------
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-SV8Y-M), Version 12.2(13)T16, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Thu 14-Apr-05 19:25 by yiyan
Image text-base: 0x80008120, data-base: 0x81190E44
ROM: System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
ROM: C1700 Software (C1700-SV8Y-M), Version 12.2(13)T16, RELEASE SOFTWARE (fc1)
yourname uptime is 4 minutes
System returned to ROM by power-on
System image file is "flash:c1700-sv8y-mz.122-13.T16.bin"
cisco 1751 (MPC860P) processor (revision 0x400) with 83979K/14325K bytes of memory.
Processor board ID FOC08310YEZ (1669471188), with hardware revision 0000
MPC860P processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
------------------ show diag ------------------
Slot 0:
C1751 1FE VE DV Mainboard Port adapter, 3 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 4.0
PCB Serial Number : FOC08310YEZ
Part Number : 73-7241-04
Board Revision : B0
Fab Version : 04
Product Number : Unknown
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 02 4D 41 04 00 C1 8B 46 4F 43 30 38 33
0x10: 31 30 59 45 5A 82 49 1C 49 04 42 42 30 02 04 FF
0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Packet Voice DSP Module Slot 0:
Hardware Revision : 3.2
Part Number : 73-6726-01
Board Revision : A0
Deviation Number : 0-0
Fab Version : 03
PCB Serial Number : VIC09267FBE
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 02
Number of DSP's : 1
DSP memory size(in kwords): 256
Type of DSP : TMS320C549
Product Number : PVDM-256K-4=
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 02 AC 41 03 02 82 49 1A 46 01 42 41 30
0x10: 80 00 00 00 00 02 03 C1 8B 56 49 43 30 39 32 36
0x20: 37 46 42 45 03 00 81 00 00 00 00 04 00 09 02 FF
Packet Voice DSP Module Slot 1:
Not populated
WIC/VIC Slot 0:
Serial 2T (12in1)
Hardware revision 1.0 Board revision D0
Serial number 0024047013 Part number 800-03181-01
FRU Part Number WIC-2T=
Test history 0x00 RMA number 00-00-00
Connector type PCI
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 12 01 00 01 6E ED A5 50 0C 6D 01 00 00 00 00
0x30: 68 00 00 00 00 10 12 00 FF FF FF FF FF FF FF FF
can u pls help....

Vic card not initializing

I have recently got a router - 1751v
and also a voice card - vic-2fxs
The card is not getting initialized
amber light is glowing contineously
error showing card not initializing, unknown hardware found in slot1.
here is the sh tech support details of the router
the card is vic-2fxs
------------------ show version ------------------
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-SV8Y-M), Version 12.2(13)T16, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Thu 14-Apr-05 19:25 by yiyan
Image text-base: 0x80008120, data-base: 0x81190E44
ROM: System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
ROM: C1700 Software (C1700-SV8Y-M), Version 12.2(13)T16, RELEASE SOFTWARE (fc1)
yourname uptime is 4 minutes
System returned to ROM by power-on
System image file is "flash:c1700-sv8y-mz.122-13.T16.bin"
cisco 1751 (MPC860P) processor (revision 0x400) with 83979K/14325K bytes of memory.
Processor board ID FOC08310YEZ (1669471188), with hardware revision 0000
MPC860P processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
------------------ show diag ------------------
Slot 0:
C1751 1FE VE DV Mainboard Port adapter, 3 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 4.0
PCB Serial Number : FOC08310YEZ
Part Number : 73-7241-04
Board Revision : B0
Fab Version : 04
Product Number : Unknown
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 02 4D 41 04 00 C1 8B 46 4F 43 30 38 33
0x10: 31 30 59 45 5A 82 49 1C 49 04 42 42 30 02 04 FF
0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Packet Voice DSP Module Slot 0:
Hardware Revision : 3.2
Part Number : 73-6726-01
Board Revision : A0
Deviation Number : 0-0
Fab Version : 03
PCB Serial Number : VIC09267FBE
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 02
Number of DSP's : 1
DSP memory size(in kwords): 256
Type of DSP : TMS320C549
Product Number : PVDM-256K-4=
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 02 AC 41 03 02 82 49 1A 46 01 42 41 30
0x10: 80 00 00 00 00 02 03 C1 8B 56 49 43 30 39 32 36
0x20: 37 46 42 45 03 00 81 00 00 00 00 04 00 09 02 FF
Packet Voice DSP Module Slot 1:
Not populated
WIC/VIC Slot 0:
Serial 2T (12in1)
Hardware revision 1.0 Board revision D0
Serial number 0024047013 Part number 800-03181-01
FRU Part Number WIC-2T=
Test history 0x00 RMA number 00-00-00
Connector type PCI
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 12 01 00 01 6E ED A5 50 0C 6D 01 00 00 00 00
0x30: 68 00 00 00 00 10 12 00 FF FF FF FF FF FF FF FF
can anyone pls help....

are you sure it is a vic-2fxs and not a vic2-2fxs ?
If so then either a defective card or you may have a counterfeit card (they are out there ) does card have a sticker on it that shows an american flag and made in USA ? if so it is a counterfeit card. If it is a vic2-2fxs you cannot use it in a 1751.

4.3 Update - Car Stereo Issue, voice dialing not working with Bluetooth

I've seen some similar issues reported, but they were for specific cars/stereos, and the symptoms were different, so I'm posting about mine:
Phone: Samsung Galaxy SIII, Android 4.3.
Car Stereo: Pioneer AVH-X2500BT
This is a stereo I bought and installed myself. All of its features worked fine, and I was enjoying making calls using voice dialing via the stereo. Then, I installed the 4.3 update to the Galaxy SIII. Ever since (literally, I made a call that day before installing it, and tried shortly after), I cannot use the voice dialing feature. Any attempt to use voice dialing or voice commands via the car stereo will fail. Here's what happens:
I do a long press on the car stereo's Home button to initiate voice dialing. On my phone, S-Voice starts up, and a Toast (little message) pops up briefly that says "Check in-car audio". When I talk, the little animation on the microphone button in S-Voice does not happen, meaning it's not hearing anything. The car stereo shortly cancels out of voice dialing mode, as though it timed out, or something.
I've tried switching to Google voice, but the same thing happens. I've tried all kinds of configuration on both devices. I've unpaired and re-paired. Nothing.
Also, turn-by turn directions from Google Maps appears to not work. The app thinks it's giving them, and when I turn the car off, the voice suddenly works from the phone, but it just won't come out the stereo.
All other features work fine, including Pandora, and streaming Bluetooth audio. I can even make phone calls, by accessing the contacts and recent call list from the car stereo. The calls work and come through the stereo fine. Literally voice dialing and Google Maps are all that doesn't work.
Does anyone know how to fix this?

There could be any number of factors that may be affecting this, byounie. It may be that the firmware on your car stereo headunit may need to be updated. My direct recommendation to check first would be to access your bluetooth submenu, and next to paired info for the Pioneer AVH-X2500BT, you should see a little cog wheel/settings icon. Please select this, and start unselecting everything available there. Work your way up, and enable and test these different settings one by one, to see if there is a conflict between Google Maps and Voice dialing services. Let us know what happens, byounie.
NicandroN_VZW
Follow us on twitter @VZWSupport

Urgent,voice card problem

. hi all,
my friend have bought iphone 5s 32 gb from london for me. but my phone is problem either screen or voice card. How can ı use international guaranty?
best regards
my phone
Model: ME437B/A
Serian Number: DNPLK8XYFFGG
IMEI:35 876105 156176 4
ICC ID: 8990 0112 0714 0004 864
Taner BADEM

If you lost your memory card password, it is not possible to recover data on it.
But atleast you can save your memory card by using a trick.
Just insert your memory card into a smartphone like Nokia E66 which i have tried.
Now try to format, and it works without need of your forgotten password.
You know what
these Smartphone won't ask for password
Please click on Kudo button if my post helped to save your memory card.
-------------------If this post helped you, click on accept as solution.------------------
-----------------------------Appreciate by clicking on white star.----------------------------

Router 2911 with voice card VIC3-E/M VOIP Problem

hi All
I want to ask if any of you have any experience like this. I have deployed a new Cisco router (model 2911) in my client. The previous router they used is 2811. After deployement, the WAN & LAN connection work fine, but the VOIP connection does not work.
The previous router (2811) uses a voice card module VIC2-e/m. But the new router (2911) use voice card module VIC3-e/m. It is used to connect to the PABX Panasonic TD-1232.
Could this be a factor?
Can anyone help?

Hi,
In addition to what Terry has said, the only change is IOS 15.1 where Toll Fraud Prevention feature was introduced which says
The router will automatically add any destinations that are defined as an ipv4 target in a VoIP dial-peer to the trusted source list.You can run the command
show ip address trusted list
To overcome this behaviuor, you can follow the three ways as suggested in below link .The one has been already suggested by Terry.
https://supportforums.cisco.com/document/46566/understanding-toll-fraud-enhancements-1512t
your 28XX router has 12.4 IOS version
regds,
aman

2811 w/CableDocsis and AP-AG card not recognized

Just purchased a 2811 router with voice and wan cards. The voice cards pick up fine. For whatever reason, can't recognize the HWIC-Cable card and the HWIC-AP-AG card. with a show diag I get the following
WIC Slot 0:
Unknown WAN daughter card
WIC module not supported/disabled in this slot
This happens for both cards but the voice cards come up fine. Have tried swapping the cards/slots around to no avail.
Currently running
Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(3g), RELEASE SOFTWARE (fc2)
which I believe should support these HWIC cards. Anyone have any idea as to why I can't get either of these WAN cards to recognize in this 2811 ? Thanks.

The Motherboard WIC slots are numbered from 0 to 3 and the Cisco cable HWIC is supported in the WIC slots of Cisco IAD2431.
If you want to know more please click the following link:
http://www.cisco.com/en/US/products/hw/routers/ps282/products_tech_note09186a008035b051.shtml

Error "can not start the configuration in parallel does not correct"

Hello everybody,
I have Windows 7 SP1, and when I install Business Objects 4.1 Client, it is install correctly but when i execute the program, for example BO Rich Client, an error appear "can not start the configuration in parallel does not correct" Could you help me?
Thanks in advance!

Check this KB
1678498 - BI 4.0 Universe Designer Gives Side-by-Side configuration incorrect Error

Runtime error R6025 message after log on to Vista - Flash Card not working

Hi
I'm a newbie & would appreciate any advice.
I am getting a runtime error message R6025 when I log on to Windows Vista.
When I click out of the box I then get a message saying Toshiba Flash Card not working.
I cancel that and my laptop is ok except I don't know if the flashcard is working or not because I don't know what it does.
Sorry if I sound thick
Thanks
Neelie

Hi
I found this MS knowledge base article:
+Description of the R6025 run-time error in Visual C++\+
http://support.microsoft.com/kb/125749
But I doubt this description would be useful for you or anyone here. It describes this error in Visual C++ and this is programming language.
However, I think you should simply reinstall the Value Added Package which you could download firstly from the Toshiba European page.
At first you have to remove the old Value Added Package from the system, then reboot the notebook and follow with new VAP installation.
Bye

IPhone 2G voice mic not working

Has anyone come across iPhone 2G voice mic not working (not being heard by the other person) but works fine on speaker phone and bluetooth headset. It has been working fine so far and suddenly developed this problem! Any help is highly appreciated….

I had that problem with my iPhone 3G after about 5 days.
I just had Apple take a look at it.
They cleaned it out, called it and stuff.
Didn't work.
Since I didn't drop it in water and it was not my fault in any way, they gave me a brand new one.

Installed i0S 8 and now my iPhone 4s voice mail not working

installed i0S 8 and now my iPhone 4s voice mail not working

Well, what happens when you try to use it. That would help in the troubleshooting. Have you contacted your cellular carrier? Voicemail is a carrier function.

GeForce4 TI Video Card Not Recognized Anymore?

For about almost a year, the fan on the GeForce4 TI video card would occasionally make a grinding noise, although it has always been easily fixed by lightly sticking a finger on the fan to stop it for a second and it would go back to normal.
However, about a month ago this little fix stopped working. The grinding noise was unbearable. After searching the Internet for a few minutes, I found out that I wasn't the only one suffering from this problem, and some even offered tips on how to replace the fan.
I followed the steps very carefully and made sure the card was not harmed. After installing the new fan, which was very easy, I stuck it back into the Power Mac and boot it up. However the monitor didn't find a signal.
I was glad that I installed Remote Desktop on the Power Mac so I was able to connect to it and see what's going on. I opened Apple System Profiler and noticed that the computer isn't properly recognizing the graphics card anymore! Instead of the very detailed information I'm used to seeing, this is what I saw below:
pci10de,a:
Type: VGA-Compatible Controller
Bus: AGP
Slot: SLOT-1
Vendor: nVIDIA (0x10de)
Device ID: 0x252
Revision ID: 0x00a3
I have no clue what this means as it seems like the computer still recognizes A video card. Also this also gave me the impression that the Power Mac is missing the drivers, but that's impossible as I haven't touched the software on the hard drive and nVidia drivers are part of OS X.
If the card is broken then fine, I'll take my losses and buy a new one as I would hate to just throw the computer away since it still more than fulfill my needs. But I just hope the AGP slot isn't broken.
Any ideas? Thanks in advance.

Just for clarification:
You have two systems based on the same MS-7008 mainboard, correct? Both use the same BIOS Version?
In one system, the card is functioning, running in AGP 3.0 Mode x8 and in the other, same mainboard model, what are the symptoms of "video card not recognized" besides the AGP 2.0 Mode x4 limitation?
I mean, if you can see the BIOS Setup, the card is putting something out on the screen, right?

Not able to configure SSH

Hi,
I'm using 1841 router.My question is I'm not able to configure SSH in this router ,Any IOS problem?
Sh version
Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(1c), RELEASE SO
FTWARE (fc1)

Hi Karthick
You are currently running IP BASE Feature Set ios on your router you need to upgrade the same to Advanced Security Services or SP Services Feature set to have SSH support in your router..
http://www.cisco.com/en/US/products/sw/iosswrel/ps5460/index.html
regds

When streaming a movie with the new Apple TV, and using a DSL Internet connection, all audio sound works, e.g., the music track, but the audio track with the actor's voices, does not work. What can I do?

When streaming a movie with the new Apple TV, and using a DSL Internet connection, all audio sound works, e.g., the music track, but the audio track with the actor's voices, does not work. What can I do?

Hi Brian,
Thanks restoring and restarting didn't fix my problem - i have started it fresh and still it doesn't work. Basically I press ONCE on the remote, after the machine has not had any commands for 10 minutes, and the cursor skips from one end of the menu to the other - so I can't choose network or update software etc - I sometimes manage to stop it randomly in the middle of the menu if I press on a command in the middle of the cursor skipping all the menu steps...not sure what the problem is but I have basically not used my brand new apple tv since I bought it for that reason! I should call Apple support I suppose! grrrr hate wasting time with stuff like this!
Thanks for your help though!
Pernille

How to download a pdf file in external storage(sd-card) not use a isolated storage wp8

i have a url for download pdf file return by webservices
and i have attach this link in hypertext button this is start a download but in browser . and when i am google for this purpose the give me "
Background file transfer
" Process and then code is also using a isolated storage but i want a external storage process Please Help me
how to download a pdf file in external storage(sd-card) not use a isolated storage wp8

Hello,
This forum is for discussions and questions regarding profiles and Microsoft's recognition system on the MSDN and TechNet sites. It is not for products/technologies.
As it's off-topic here, I am moving the question to the
Where is the forum for... forum.
Karl
When you see answers and helpful posts, please click Vote As Helpful, Propose As Answer, and/or Mark As Answer.
My Blog: Unlock PowerShell
My Book: Windows PowerShell 2.0 Bible
My E-mail: -join ('6F6C646B61726C40686F746D61696C2E636F6D'-split'(?<=\G.{2})'|%{if($_){[char][int]"0x$_"}})

Voice card not appaering in configuration?

Similar Messages

Maybe you are looking for