Voice Gateway echo problem
Hi,
My Cisco 2821 router have 2 PVDM2-64. The "sh call active voice echo-cancel summ" result are A/F :
Voice-GW#sh call active voice echo-can summ
CallID Port DSP/Ch Codec Ecan-type Tail Called # Dial-peers
0x111BDFE 0/1/0:15.30 0/1:5 g711ulaw SW-Extend 64 ms *29277728 797/22
0x111BEB2 0/1/1:15.31 0/1:1 g711ulaw SW-Extend 64 ms *082311888 797/40
0x111BEB4 0/1/0:15.31 0/1:2 g711ulaw SW-Extend 24 ms *62379 797/26
We find that the call at port 0/1/0:15.31 have echo problem. We monitor several times and find the echo occured when the DSP/Ch is 0/1:2 or 0/2:2. Please help to mention me the DSP/Ch 0/1:2 or 0/2:2 is which PVDM2-64? Does it mean one of my PVDM2-64 failed? If yes, which one of PVDM2 failed?
Best Regards,
We tried to upgrade IOS from 124-15.T4 to 124-25g and monitor about one days, the echo problem seems not occurred again. Please help to mention me why you recommand to upgrade IOS? Thanks a lot...
Similar Messages
-
Voice gateway SPA8000 problem sending faxes.
Hello, I am a representative of the corporation Kazakhmys using the whole range of your devices. The problem is as follows: Voice Gateway Cisco SPA 8000 does not send faxes to voice gateway Grandstream GXW4232. The problem occurs only if the two voice gateways work with each other. The call comes to the SPA 8000, but after lifting the handset, the session immediately reset. What settings I need to change?
It seems you have RTP packet Size set to 30ms. It's not optimal even for voice call. You should not exceed 20ms for voice, for the fax I propose you to use 10ms.
Note it may not solve your problem, but it increase reliability of fax session.
But now back to the issue. If I understand correctly, the attached log has been captured on
Cisco-SIPGateway/IOS-15.2.4.M7
OK. It seem that most important line of such log is:
068963: Feb 24 05:50:16.778: //6170583/D6D178518A93/CCAPI/cc_api_call_disconnect_done:
Disposition=0, Interface=0x160DE9D8, Tag=0x0, Call Id=6170583,
Call Entry(Disconnect Cause=3, Voice Class Cause Code=0, Retry Count=0)
If I understand correctly the log, the call has been terminated by SIP Gateway.
I see no apparent issue with ATA8000 (not counting the Packet Size value mentioned on top). There is a problem with SIP Gateway. Unfortunately, I'm not expert on the matter nor this forum is best forum for question related to SIP Gateway. You should ask on IP Telephony forum instead. -
Call Manager register fxs port with voice gateway- problem
I have a CUCM 6 and a Voice Gateway V224. I've configured the voice gateway's voice FXS ports as MGCP.
I have a Voip connected and registered to the CUCM and a Pots phone connected to the Voice Gateway.
If i dial from the Voip to the Pots phone it rings. The problem is that i cannot ring from the Pots to the Voip phone.
I have no dial tone.
If i write no shut down on the voice port i have a tone. If i configure mgcp on the voice port i have a busy ringtone.
I've entered no mgcp and mgcp commands and i've reset the voice gateway.
How can i call from the pots to the voip phone?
The ios version on the voice gateway is Version 12.4(22)T4.
Here is an outghtput from the Voice gateway.
ccm-manager mgcp
ccm-manager fax protocol cisco
ccm-manager music-on-hold
ccm-manager config server 10.1.1.33
ccm-manager config
mgcp
mgcp call-agent CCMIOSS 2427 service-type mgcp version 0.1
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
mgcp package-capability sst-package
no mgcp package-capability res-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp validate domain-name
mgcp rtp payload-type g726r16 static
mgcp profile default
timeout tone busy 600
timeout tone dial 600
dial-peer voice 999223 pots
service mgcpapp
port 2/23
dial-peer voice 999222 pots
service mgcpapp
port 2/22
dial-peer voice 999888 pots
service mgcpapp
port 2/23
The CUCM 6 is registered with the voice gateway.Is your campaign using CPA? If so, what's the behavior if CPA is not enabled?
I think the best thing to do is to run a trace...
Call Manager > Cisco Unified Serviceability > Trace > Configurations
Select a CUCM server - any subscriber would work.
Service Group - CM Services
Cisco CallManager (Inactive)
Enable SIP Stack Trace and apply to all nodes. Download and install RTMT
Make a bunch of outbound tests and then open RTMT > Trace & Log Central > Collect Files > Check "All Servers" for Cisco CallManager > Next > Next > Relative Range if you made the test calls within the last X minutes, otherwise you can set a From and To datetime. Click Finish and go through your SDL logs and see what errors you find and post them here.
Also, make sure your phone is in the correct CSS in Call Manager -
IP phone user hears an echo of his voice on a call to a PSTN phone. It looks like an issue with the voice gateway. Checked the cisco document
http://www.cisco.com/en/US/tech/tk652/tk698/technologies_tech_note09186a0080149a1f.shtml
Set the echo canceller converge to the highest value (64ms). But the users are still experiencing echo problems.
Attached pls find the output of "show voice active".
IOS 12.4.6T on Cisco 2811
Appreciate any input.There is a known bug with that version of IOS and the DSPs on it...bug CSCsd54344
DSP: Persistent echo heard on c5510 DSPs with 4.4.13 DSPware or higher
http://www.cisco.com/cgi-bin/Support/Bugtool/onebug.pl?bugid=CSCsd54344
use show voice dsp group all to see if it is using DSP version 4.4.708. If it is you either need to go up to 12.4.9T (first fixed version) or downgrade the DSP (easiest option) to version 4.4.706.
You can call TAC about getting that file if needed. -
IP2IP Gateway Transcoding Problem
I have a test IP to IP Gateway on 2811 with PVDM2-16 DSPs.
The software is c2800nm-ipvoice_ivs-mz version 12.3(11)T7.
Accortding to the documentation it should be able to do transcoding between inbound
and ourbound call legs (Transcoding G.711-G.729). However, the configuration guide points to
Configuring Enhanced Conferencing and Transcoding for Voice Gateway Routers chapter
of the Cisco CallManager and Cisco IOS Interoperability Guide. This configuration is for
CallManager transcoders. But I need the gateway to do transcoidng and do so with NO need
for CallManager. The gatway is not registered in gatekeeper also. It should be standalone
and make static routing of h323 calls between endpoints.
I've searched in the documentation but I did not find any configurations
that I can use. I made a lot of tests with diferents configurations but when there is no match
in codec betweend in and out legs (with slowstart) the debug says:
*Aug 18 11:10:03.030: //2546/3AD381928396/H323/cch323_prepare_preferred_codec_list: Check the filter: Not a single match
*Aug 18 11:10:03.030: //2546/3AD381928396/H323/cch323_peer_caps_ind_common: No Matching Codec after filtering. Hence try to find xcoder
When faststart is enabled the two call legs have different codecs in " show call history " but I here strange sounds
which means that there is no proper ( or no at all) transocding in the gateway but the endpints try to decode the incorect codec.
So I don't know if this is some problem in this recent version of IOS or I have to make some reconfigurations or even change the DSPs.
Or may be it's not (yet) possible to to this kind of transcoding and I misunderstood the features description in the docs?
Any ideas are welcome!I could go out-of-topic, but the best thing (with a reasonable price) I have seen to do codec translation is the MERA MVTS softswitch.
Asterisk PBX can do it as well, but it need licenses for the G729 codec and its H323 support is crappy. -
Can't establish a Voice gateway (cisco 2911) using SIP with CUCM 9.1
I have configured a Cisco 2911 as a Voice Gateway using SIP (the configuration is attached), but unfortunately can't establish a test call to a phone (CUPC 8.6 SCCP) using csim start. I have done logging the ccsip debug and ccapi debug and attached them. Could anyone help me to solve this problem?
I just did some research on my end and csim is not supported for SIP. The Invite will never be created and sent to the CUCM to initate the call. It disconnects in the router itself with normal cause.
*Apr 18 08:58:48.086: //40/7D08458F8077/SIP/Error/sipSPIOutgoingCallSDP:
Could not create source SDP for Outgoing Call
*Apr 18 08:58:48.086: //40/7D08458F8077/SIP/Error/sipSPICreateOutboundSDP:
Error in creating an SDP for the outbound call - Check for supported codecs
*Apr 18 08:58:48.086: //40/7D08458F8077/SIP/Error/preprocessSetup:
Error during outbound SDP creation
*Apr 18 08:58:48.086: //40/7D08458F8077/SIP/Info/sipSPIInitiateDisconnect: Initiate call disconnect(16) for outgoing call
Please use an actual call to test your dial-peer and integration with call manager. csim will not work.
Hantale
Sree -
VG 224 Voice Gateway using MCGP or fax
Does anyone have a experience or a config for running MGCP on a VG224 voice gateway (using it for inbound/outbound fax)to Call Manager? I've set up SCCP and it worked initially but in production it drops calls and does not respond after reboot without re-enabling SCCP and STAPP
I deployed 5 of these to service a mix of phones and faxes a few months ago using MGCP.
I used fax passthrough; we've had 0 problems so far with the setup.... customer has had several power cuts and no startup problems.
Regards
Aaron
Please rate helpful posts... -
E50 Echo Problem & No Help From Nokia Turkey
Hi,
I'm using Nokia E50 for two months. Whenever I have a call (in or out) am receiving the same complaint from the other side of the line : The guy who is talking with me always hearing his/her own voice during the call. Echo issue.
I've called the Nokia Turkey Call Center they told me that they've never been advised a case for the ECHO problem !!! Apparently they don't even hear the Google since there is hundreds of similar case !!!
I took the phone to the official Nokia Repair Shop they've just checked the software and the patches and all of them were fully updated. Unfortunately they don' have any idea what's going on.
Appreciate if anyone help me out about the issue, otherwise I'm going to give back to phone since it's still within legal warranty period.
Regards
Kivanc PakelMessage Edited by kpakel on 15-Dec-2006
08:59 PMWe have seen the same problem with 2 E50s my company has just bought. I thought it was the new BT car kit that people were complaining about until I called my colleague with the new phone for the first time and we got DOUBLE ECHO!!!
The latest firmware does not seem to fix this problem as of Jan 07. Have tried adjusting the volume down to no avail, so no other suggestions, but rest assured you are not alone. -
Hi everyone!
Have had an N70 for just over a week and am already on my second handset.
When using my phone - the person I am calling complains of a bad echo of their own voice - but it sounds perfect at my end. This is not when on handsfree, but when I make a normal call.
If i turn the phone off and then on again it seems to be ok for a little while, then the echos start again.
Vodafone suggested in the first week that it was probably a mic fault and changed the handset for a brand new one. The brand new one was ok for a couple of days, and now it is echoing again.
Anyone got any ideas why it is doing this?
I do connect to a tomtom Go 500 via bluetooth and handsfree calling on that is fine - the echo is only evident when I'm not connected to the tomtom.
Many thanks
VickyI've also had exactly the same problems - along with six N70s, 3 x 3G sims & a 2G sim replacements since 11th January. I've just had the latest software put on my phone & the echo problem started yet again 2 hours later. I have now tried (only yesterday) the phone with bluetooth turned off and so far it's lasted @ 26 hours without an echo.
-
Hi everyone,
I just bought my new K860 smartphone last Dec 2012, I didn't notice it until one of my friends told me that his voice is echoing when I call him, I tried to call my other friends and have the same scenario.. Please help.. Thanks!Have you tried a factory reset to see if it was a setting? If problem exists after a reset, then it would be a hardware issue that would need to be repaired.
IT Specialist and Consultant
Lenovo Tablet Evangelist
Current Machines: IdeaCentre A300, ThinkPad Tablet, IdeaPad U410, and Yoga 3 Pro Touch
Deutsche Community Comunidad en Español
Lenovo - the latest in DOtabs, DOpads, DOcentre's, DOstations and DOservers! -
Hello all,
Whenever somebody call's me or I call them they are complaining that they hear an echo of their own voice.
This problem only occurs after I use my e60 in combination with the integrated bluetooth carkit from Peugeot. When I switch the phone off and on again, the problem is gone.
My phone already has got the latest firmware and I know somebody with the same phone who has the problem with the bluetooth carkit of bmw.
Can somebody help me with this please.
Thanks,
Best RegardsI have the same problem. Called over and over to Nokia.
They are unwilling to solve this. Since the carkit (in my case a Pioneer Bluetooth Radio) is not a Nokia accessoire.
Real pitty and a showstopper for business users like me. -
Cisco 2911 Voice Gateway SIP PSTN Calls Fail
Hello All,
I am having trouble with outboud SIP PSTN calls through a Cisco 2911 Voice Gateway. 2911 VG terminates PSTN SIP Traffic and connects to Avaya CS1000M via QSIG PRI Trunks. When calls are attempted outbound fron the PBX the caller gets a fast busy. Debug ISDN q931 shows the call hitting the 2911 properly, debug voip ccapi inout shows the call matching the correct dial peers and debug ccsip shows the invite to the PSTN Provider SBC, however within the invite the "from" address incorrectly shows the calling number with the provider SBC address (see below). does anyone have any insight on how to correct this? Attached are VG config and Debug isdn q931, voip ccapi inout, ccsip messages and ccsip call. Thanks in advance for any help!!
From: <sip:[email protected]>:tag=6166CDC4-882
To: <sip:[email protected]>
Shawn C. Smithi have same problem my cucm ip is 192.168.200.53
my Voice Gateway is SIP by ip 192.168.200.86 for internal
and 172.29.7.94
and my SIP Server is 10.208.9.69
if its oky can yuo take a look at my problem please
this is the syslog from debug
May 30 20:19:34.284: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Received:
INVITE sip:[email protected]:5060 SIP/2.0
Via: SIP/2.0/UDP 192.168.200.53:5060;branch=z9hG4bK3bd451bf17e0
From: "Aysar Mohamed" <sip:[email protected]>;tag=37693~244641b0-36ac-434c-91c1-823f25a68b28-18299026
To: <sip:[email protected]>
Date: Fri, 30 May 2014 20:19:34 GMT
Call-ID: [email protected]
Supported: timer,resource-priority,replaces
Min-SE: 1800
User-Agent: Cisco-CUCM8.6
Allow: INVITE, OPTIONS, INFO, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY
CSeq: 101 INVITE
Expires: 180
Allow-Events: presence, kpml
Supported: X-cisco-srtp-fallback
Supported: Geolocation
Call-Info: <sip:192.168.200.53:5060>;method="NOTIFY;Event=telephone-event;Duration=500"
Cisco-Guid: 3047462016-0000065536-0000004549-0902342848
Session-Expires: 1800
P-Asserted-Identity: "Aysar Mohamed" <sip:[email protected]>
Remote-Party-ID: "Aysar Mohamed" <sip:[email protected]>;party=calling;screen=yes;privacy=off
Contact: <sip:[email protected]:5060>
Max-Forwards: 70
Content-Length: 0
May 30 20:19:34.284: //-1/B5A494800000/CCAPI/cc_api_display_ie_subfields:
cc_api_call_setup_ind_common:
cisco-username=2217156
----- ccCallInfo IE subfields -----
cisco-ani=2217156
cisco-anitype=0
cisco-aniplan=0
cisco-anipi=0
cisco-anisi=1
dest=90555769123
cisco-desttype=0
cisco-destplan=0
cisco-rdie=FFFFFFFF
cisco-rdn=
cisco-rdntype=0
cisco-rdnplan=0
cisco-rdnpi=-1
cisco-rdnsi=-1
cisco-redirectreason=-1 fwd_final_type =0
final_redirectNumber =
hunt_group_timeout =0
May 30 20:19:34.288: //-1/B5A494800000/CCAPI/cc_api_call_setup_ind_common:
Interface=0x30CF41D4, Call Info(
Calling Number=2217156,(Calling Name=)(TON=Unknown, NPI=Unknown, Screening=User, Passed, Presentation=Allowed),
Called Number=90555769123(TON=Unknown, NPI=Unknown),
Calling Translated=FALSE, Subscriber Type Str=Unknown, FinalDestinationFlag=TRUE,
Incoming Dial-peer=0, Progress Indication=NULL(0), Calling IE Present=TRUE,
Source Trkgrp Route Label=, Target Trkgrp Route Label=, CLID Transparent=FALSE), Call Id=465
May 30 20:19:34.288: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
May 30 20:19:34.288: :cc_get_feature_vsa malloc success
May 30 20:19:34.288: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
May 30 20:19:34.288: cc_get_feature_vsa count is 1
May 30 20:19:34.288: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
May 30 20:19:34.288: :FEATURE_VSA attributes are: feature_name:0,feature_time:832953048,feature_id:85
May 30 20:19:34.288: //465/B5A494800000/CCAPI/cc_api_call_setup_ind_common:
Set Up Event Sent;
Call Info(Calling Number=2217156(TON=Unknown, NPI=Unknown, Screening=User, Passed, Presentation=Allowed),
Called Number=90555769123(TON=Unknown, NPI=Unknown))
May 30 20:19:34.288: //465/B5A494800000/CCAPI/cc_process_call_setup_ind:
Event=0x2B82D890
May 30 20:19:34.288: //-1/xxxxxxxxxxxx/CCAPI/cc_setupind_match_search:
Try with the demoted called number 90555769123
May 30 20:19:34.288: //465/B5A494800000/CCAPI/ccCallSetContext:
Context=0x2ABC2E44
May 30 20:19:34.288: //465/B5A494800000/CCAPI/cc_process_call_setup_ind:
>>>>CCAPI handed cid 465 with tag 0 to app "_ManagedAppProcess_Default"
May 30 20:19:34.288: //465/B5A494800000/CCAPI/ccCallProceeding:
Progress Indication=NULL(0)
May 30 20:19:34.288: //465/B5A494800000/CCAPI/ccCallSetupRequest:
Destination=, Calling IE Present=TRUE, Mode=0,
Outgoing Dial-peer=802, Params=0x2ABC19D4, Progress Indication=NULL(0)
May 30 20:19:34.288: //465/B5A494800000/CCAPI/ccCheckClipClir:
In: Calling Number=2217156(TON=Unknown, NPI=Unknown, Screening=User, Passed, Presentation=Allowed)
May 30 20:19:34.288: //465/B5A494800000/CCAPI/ccCheckClipClir:
Out: Calling Number=2217156(TON=Unknown, NPI=Unknown, Screening=User, Passed, Presentation=Allowed)
May 30 20:19:34.288: //465/B5A494800000/CCAPI/ccCallSetupRequest:
Destination Pattern=9T, Called Number=0555769123, Digit Strip=FALSE
May 30 20:19:34.288: //465/B5A494800000/CCAPI/ccCallSetupRequest:
Calling Number=2217156(TON=Unknown, NPI=Unknown, Screening=User, Passed, Presentation=Allowed),
Called Number=0555769123(TON=Unknown, NPI=Unknown),
Redirect Number=, Display Info=Aysar Mohamed
Account Number=2217156, Final Destination Flag=TRUE,
Guid=B5A49480-0001-0000-0000-11C535C8A8C0, Outgoing Dial-peer=802
May 30 20:19:34.288: //465/B5A494800000/CCAPI/cc_api_display_ie_subfields:
ccCallSetupRequest:
cisco-username=2217156
----- ccCallInfo IE subfields -----
cisco-ani=2217156
cisco-anitype=0
cisco-aniplan=0
cisco-anipi=0
cisco-anisi=1
dest=0555769123
cisco-desttype=0
cisco-destplan=0
cisco-rdie=FFFFFFFF
cisco-rdn=
cisco-rdntype=0
cisco-rdnplan=0
cisco-rdnpi=-1
cisco-rdnsi=-1
cisco-redirectreason=-1 fwd_final_type =0
final_redirectNumber =
hunt_group_timeout =0
May 30 20:19:34.288: //465/B5A494800000/CCAPI/ccIFCallSetupRequestPrivate:
Interface=0x30CF41D4, Interface Type=3, Destination=, Mode=0x0,
Call Params(Calling Number=2217156,(Calling Name=Aysar Mohamed)(TON=Unknown, NPI=Unknown, Screening=User, Passed, Presentation=Allowed),
Called Number=0555769123(TON=Unknown, NPI=Unknown), Calling Translated=FALSE,
Subscriber Type Str=Unknown, FinalDestinationFlag=TRUE, Outgoing Dial-peer=802, Call Count On=FALSE,
Source Trkgrp Route Label=, Target Trkgrp Route Label=, tg_label_flag=0, Application Call Id=)
May 30 20:19:34.288: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
May 30 20:19:34.288: :cc_get_feature_vsa malloc success
May 30 20:19:34.288: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
May 30 20:19:34.288: cc_get_feature_vsa count is 2
May 30 20:19:34.288: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
May 30 20:19:34.288: :FEATURE_VSA attributes are: feature_name:0,feature_time:832952824,feature_id:86
May 30 20:19:34.292: //466/B5A494800000/CCAPI/ccIFCallSetupRequestPrivate:
SPI Call Setup Request Is Success; Interface Type=3, FlowMode=1
May 30 20:19:34.292: //466/B5A494800000/CCAPI/ccCallSetContext:
Context=0x2ABC1984
May 30 20:19:34.292: //465/B5A494800000/CCAPI/ccSaveDialpeerTag:
Outgoing Dial-peer=802
May 30 20:19:34.292: //466/B5A494800000/CCAPI/cc_api_call_proceeding:
Interface=0x30CF41D4, Progress Indication=NULL(0)
May 30 20:19:34.292: //465/B5A494800000/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 100 Trying
Via: SIP/2.0/UDP 192.168.200.53:5060;branch=z9hG4bK3bd451bf17e0
From: "Aysar Mohamed" <sip:[email protected]>;tag=37693~244641b0-36ac-434c-91c1-823f25a68b28-18299026
To: <sip:[email protected]>
Date: Fri, 30 May 2014 20:19:34 GMT
Call-ID: [email protected]
CSeq: 101 INVITE
Allow-Events: telephone-event
Server: Cisco-SIPGateway/IOS-12.x
Content-Length: 0
May 30 20:19:34.292: //466/B5A494800000/SIP/Msg/ccsipDisplayMsg:
Sent:
INVITE sip:[email protected]:5060 SIP/2.0
Via: SIP/2.0/UDP 172.29.7.94:5060;branch=z9hG4bK461C
Remote-Party-ID: "Aysar Mohamed" <sip:[email protected]>;party=calling;screen=yes;privacy=off
From: "Aysar Mohamed" <sip:[email protected]>;tag=7394E4-1898
To: <sip:[email protected]>
Date: Fri, 30 May 2014 20:19:34 GMT
Call-ID: [email protected]
Supported: timer,resource-priority,replaces,sdp-anat
Min-SE: 1800
Cisco-Guid: 3047462016-0000065536-0000004549-0902342848
User-Agent: Cisco-SIPGateway/IOS-12.x
Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
CSeq: 101 INVITE
Timestamp: 1401481174
Contact: <sip:[email protected]:5060>
Call-Info: <sip:172.29.7.94:5060>;method="NOTIFY;Event=telephone-event;Duration=2000"
Expires: 180
Allow-Events: kpml, telephone-event
Max-Forwards: 69
Session-Expires: 1800
Content-Length: 0
May 30 20:19:34.300: //466/B5A494800000/SIP/Msg/ccsipDisplayMsg:
Received:
SIP/2.0 100 Trying
Via: SIP/2.0/UDP 172.29.7.94:5060;branch=z9hG4bK461C
Call-ID: [email protected]
From: "Aysar Mohamed"<sip:[email protected]>;tag=7394E4-1898
To: <sip:[email protected]>
CSeq: 101 INVITE
Content-Length: 0
May 30 20:19:34.612: //466/B5A494800000/SIP/Msg/ccsipDisplayMsg:
Received:
SIP/2.0 183 Session Progress
Via: SIP/2.0/UDP 172.29.7.94:5060;branch=z9hG4bK461C
Record-Route: <sip:10.208.9.69:5060;transport=udp;lr>
Call-ID: [email protected]
From: "Aysar Mohamed"<sip:[email protected]>;tag=7394E4-1898
To: <sip:[email protected]>;tag=sbc0806eppk5yip-CC-57
CSeq: 101 INVITE
Contact: <sip:[email protected]:5060;user=phone>
Allow: INVITE,ACK,OPTIONS,BYE,CANCEL,REGISTER,INFO,PRACK,SUBSCRIBE,NOTIFY,UPDATE,MESSAGE,REFER
Content-Length: 328
Content-Type: application/sdp
v=0
o=- 17192647 17192647 IN IP4 10.208.9.69
s=SBC call
c=IN IP4 10.208.9.69
t=0 0
m=audio 39910 RTP/AVP 8 0 102 102 18 116
a=rtpmap:8 PCMA/8000
a=rtpmap:0 PCMU/8000
a=rtpmap:102 AMR/8000
a=rtpmap:102 AMR/8000
a=rtpmap:18 G729/8000
a=rtpmap:116 telephone-event/8000
a=ptime:5
a=fmtp:116 0-15
a=fmtp:18 annexb=yes
May 30 20:19:34.612: %SIP-3-UNSUPPORTED: Unsupported ptime value
May 30 20:19:34.612: //466/B5A494800000/CCAPI/cc_api_caps_ind:
Destination Interface=0x0, Destination Call Id=-1, Source Call Id=466,
Caps(Codec=0x2, Fax Rate=0x2, Vad=0x1,
Modem=0x0, Codec Bytes=160, Signal Type=2)
May 30 20:19:34.612: //466/B5A494800000/CCAPI/cc_api_caps_ind:
Caps(Playout Mode=1, Playout Initial=60(ms), Playout Min=40(ms),
Playout Max=1000(ms), Fax Nom=300(ms))
May 30 20:19:34.612: //465/B5A494800000/CCAPI/cc_api_caps_ack:
Destination Interface=0x0, Destination Call Id=-1, Source Call Id=465,
Caps(Codec=g729r8(0x4), Fax Rate=FAX_RATE_VOICE(0x2), Vad=ON(0x2),
Modem=OFF(0x0), Codec Bytes=20, Signal Type=2, Seq Num Start=3882)
May 30 20:19:34.612: //465/B5A494800000/CCAPI/cc_api_caps_ack:
Destination Interface=0x0, Destination Call Id=-1, Source Call Id=465,
Caps(Codec=g729r8(0x4), Fax Rate=FAX_RATE_VOICE(0x2), Vad=ON(0x2),
Modem=OFF(0x0), Codec Bytes=20, Signal Type=2, Seq Num Start=3882)
May 30 20:19:34.612: //466/B5A494800000/CCAPI/cc_api_event_indication:
Event=170, Call Id=466
May 30 20:19:34.612: //466/B5A494800000/CCAPI/cc_api_event_indication:
Event Is Sent To Conferenced SPI(s) Directly
May 30 20:19:34.612: //466/B5A494800000/CCAPI/cc_api_event_indication:
Event=98, Call Id=466
May 30 20:19:34.612: //466/B5A494800000/CCAPI/cc_api_event_indication:
Event Is Sent To Conferenced SPI(s) Directly
May 30 20:19:34.612: //466/B5A494800000/CCAPI/cc_api_call_cut_progress:
Interface=0x30CF41D4, Progress Indication=INBAND(8), Signal Indication=SIGNAL RINGBACK(1),
Cause Value=0
May 30 20:19:34.612: //466/B5A494800000/CCAPI/cc_api_call_cut_progress:
Call Entry(Responsed=TRUE)
May 30 20:19:34.612: //465/B5A494800000/CCAPI/ccCallCutProgress:
Progress Indication=INBAND(8), Signal Indication=SIGNAL RINGBACK(1), Cause Value=0
Voice Call Send Alert=FALSE, Call Entry(Alert Sent=FALSE)
May 30 20:19:34.612: //465/B5A494800000/CCAPI/ccCallCutProgress:
Call Entry(Responsed=TRUE)
May 30 20:19:34.612: //465/B5A494800000/CCAPI/ccConferenceCreate:
(confID=0x30C11410, callID1=0x1D1, gcid=8C9E3127-E76E11E3-8274BE8C-EC3B12A0, tag=0x0)
May 30 20:19:34.616: //466/B5A494800000/CCAPI/ccConferenceCreate:
(confID=0x30C11410, callID2=0x1D2, gcid=8C9E3127-E76E11E3-8274BE8C-EC3B12A0, tag=0x0)
May 30 20:19:34.616: //465/B5A494800000/CCAPI/ccConferenceCreate:
Conference Id=0x30C11410, Call Id1=465, Call Id2=466, Tag=0x0
May 30 20:19:34.616: //465/xxxxxxxxxxxx/CCAPI/cc_api_get_xcode_stream:
May 30 20:19:34.616: cc_api_get_xcode_stream : 4702
May 30 20:19:34.616: //466/xxxxxxxxxxxx/CCAPI/cc_api_get_xcode_stream:
May 30 20:19:34.616: cc_api_get_xcode_stream : 4702
May 30 20:19:34.616: //465/B5A494800000/CCAPI/ccConferenceCreate:
May 30 20:19:34.616: ccConferenceCreate: ret1=0, codecMask1=2, bytes1=160, negot1=0, dtmf1=0
ret2=0, codecMask2=2, bytes2=160, negot2=1, dtmf2=6,
tx_dynamic_pt1=0, rx_dynamic_pt1=0, codec_mode1=0, params_bitmap1 =0
tx_dynamic_pt2=8, rx_dynamic_pt2=8, codec_mode2=0, params_bitmap2 =0
May 30 20:19:34.616: //465/B5A494800000/CCAPI/ccConferenceCreate:
delay media to slow start case, codec negotation is not done
May 30 20:19:34.616: //465/xxxxxxxxxxxx/CCAPI/cc_api_get_xcode_stream:
May 30 20:19:34.616: cc_api_get_xcode_stream : 4702
May 30 20:19:34.616: //465/xxxxxxxxxxxx/CCAPI/cc_api_get_xcode_stream:
May 30 20:19:34.616: cc_api_get_xcode_stream : 4702
May 30 20:19:34.616: //465/B5A494800000/CCAPI/cc_api_bridge_done:
Conference Id=0x16, Source Interface=0x30CF41D4, Source Call Id=465,
Destination Call Id=466, Disposition=0x0, Tag=0x0
May 30 20:19:34.616: //466/xxxxxxxxxxxx/CCAPI/cc_api_get_xcode_stream:
May 30 20:19:34.616: cc_api_get_xcode_stream : 4702
May 30 20:19:34.616: //466/xxxxxxxxxxxx/CCAPI/cc_api_get_xcode_stream:
May 30 20:19:34.616: cc_api_get_xcode_stream : 4702
May 30 20:19:34.616: //466/B5A494800000/CCAPI/cc_api_bridge_done:
Conference Id=0x16, Source Interface=0x30CF41D4, Source Call Id=466,
Destination Call Id=465, Disposition=0x0, Tag=0x0
May 30 20:19:34.616: //465/B5A494800000/CCAPI/cc_generic_bridge_done:
Conference Id=0x16, Source Interface=0x30CF41D4, Source Call Id=466,
Destination Call Id=465, Disposition=0x0, Tag=0x0
May 30 20:19:34.616: //465/B5A494800000/CCAPI/ccConferenceCreate:
Call Entry(Conference Id=0x16, Destination Call Id=466)
May 30 20:19:34.616: //466/B5A494800000/CCAPI/ccConferenceCreate:
Call Entry(Conference Id=0x16, Destination Call Id=465)
May 30 20:19:34.616: //465/B5A494800000/CCAPI/cc_process_notify_bridge_done:
Conference Id=0x16, Call Id1=465, Call Id2=466
May 30 20:19:34.616: //465/B5A494800000/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 183 Session Progress
Via: SIP/2.0/UDP 192.168.200.53:5060;branch=z9hG4bK3bd451bf17e0
From: "Aysar Mohamed" <sip:[email protected]>;tag=37693~244641b0-36ac-434c-91c1-823f25a68b28-18299026
To: <sip:[email protected]>;tag=739628-1BDB
Date: Fri, 30 May 2014 20:19:34 GMT
Call-ID: [email protected]
CSeq: 101 INVITE
Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
Allow-Events: telephone-event
Remote-Party-ID: <sip:[email protected]>;party=called;screen=yes;privacy=off
Contact: <sip:[email protected]:5060>
Supported: sdp-anat
Server: Cisco-SIPGateway/IOS-12.x
Content-Type: application/sdp
Content-Disposition: session;handling=required
Content-Length: 233
v=0
o=CiscoSystemsSIP-GW-UserAgent 2639 5276 IN IP4 192.168.200.86
s=SIP Call
c=IN IP4 192.168.200.86
t=0 0
m=audio 18288 RTP/AVP 8 0 19
c=IN IP4 192.168.200.86
a=rtpmap:8 PCMA/8000
a=rtpmap:0 PCMU/8000
a=rtpmap:19 CN/8000
May 30 20:19:34.680: //466/B5A494800000/SIP/Msg/ccsipDisplayMsg:
Received:
SIP/2.0 500 Server Internal Error
Via: SIP/2.0/UDP 172.29.7.94:5060;branch=z9hG4bK461C
Record-Route: <sip:10.208.9.69:5060;transport=udp;lr>
Call-ID: [email protected]
From: "Aysar Mohamed"<sip:[email protected]>;tag=7394E4-1898
To: <sip:[email protected]>;tag=sbc0806eppk5yip-CC-57
CSeq: 101 INVITE
Reason: Q.850;cause=127;text="interworking unspecified"
Warning: 399 - "SoftX3000 R601-CCU Rel POS:[3103] Release from CR"
Content-Length: 0
May 30 20:19:34.680: //466/B5A494800000/CCAPI/cc_api_call_disconnected:
Cause Value=41, Interface=0x30CF41D4, Call Id=466
May 30 20:19:34.680: //466/B5A494800000/CCAPI/cc_api_call_disconnected:
Call Entry(Responsed=TRUE, Cause Value=41, Retry Count=0)
May 30 20:19:34.680: //465/B5A494800000/CCAPI/ccCallReleaseResources:
release reserved xcoding resource.
May 30 20:19:34.680: //466/B5A494800000/CCAPI/ccCallSetAAA_Accounting:
Accounting=0, Call Id=466
May 30 20:19:34.680: //465/B5A494800000/CCAPI/ccConferenceDestroy:
Conference Id=0x16, Tag=0x0
May 30 20:19:34.680: //465/B5A494800000/CCAPI/cc_api_bridge_drop_done:
Conference Id=0x16, Source Interface=0x30CF41D4, Source Call Id=465,
Destination Call Id=466, Disposition=0x0, Tag=0x0
May 30 20:19:34.680: //466/B5A494800000/CCAPI/cc_api_bridge_drop_done:
Conference Id=0x16, Source Interface=0x30CF41D4, Source Call Id=466,
Destination Call Id=465, Disposition=0x0, Tag=0x0
May 30 20:19:34.680: //465/B5A494800000/CCAPI/cc_generic_bridge_done:
Conference Id=0x16, Source Interface=0x30CF41D4, Source Call Id=466,
Destination Call Id=465, Disposition=0x0, Tag=0x0
May 30 20:19:34.680: //466/B5A494800000/SIP/Msg/ccsipDisplayMsg:
Sent:
ACK sip:[email protected]:5060 SIP/2.0
Via: SIP/2.0/UDP 172.29.7.94:5060;branch=z9hG4bK461C
From: "Aysar Mohamed" <sip:[email protected]>;tag=7394E4-1898
To: <sip:[email protected]>;tag=sbc0806eppk5yip-CC-57
Date: Fri, 30 May 2014 20:19:34 GMT
Call-ID: [email protected]
Max-Forwards: 70
CSeq: 101 ACK
Allow-Events: kpml, telephone-event
Content-Length: 0
May 30 20:19:34.684: //466/B5A494800000/CCAPI/ccCallDisconnect:
Cause Value=41, Tag=0x0, Call Entry(Previous Disconnect Cause=0, Disconnect Cause=41)
May 30 20:19:34.684: //466/B5A494800000/CCAPI/ccCallDisconnect:
Cause Value=41, Call Entry(Responsed=TRUE, Cause Value=41)
May 30 20:19:34.684: //466/B5A494800000/CCAPI/cc_api_call_disconnect_done:
Disposition=0, Interface=0x30CF41D4, Tag=0x0, Call Id=466,
Call Entry(Disconnect Cause=41, Voice Class Cause Code=0, Retry Count=0)
May 30 20:19:34.684: //466/B5A494800000/CCAPI/cc_api_call_disconnect_done:
Call Disconnect Event Sent
May 30 20:19:34.684: //-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
May 30 20:19:34.684: :cc_free_feature_vsa freeing 31A5D9F0
May 30 20:19:34.684: //-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
May 30 20:19:34.684: vsacount in free is 1
May 30 20:19:34.684: //465/B5A494800000/CCAPI/ccCallDisconnect:
Cause Value=41, Tag=0x0, Call Entry(Previous Disconnect Cause=0, Disconnect Cause=0)
May 30 20:19:34.684: //465/B5A494800000/CCAPI/ccCallDisconnect:
Cause Value=41, Call Entry(Responsed=TRUE, Cause Value=41)
May 30 20:19:34.684: //465/B5A494800000/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 503 Service Unavailable
Via: SIP/2.0/UDP 192.168.200.53:5060;branch=z9hG4bK3bd451bf17e0
From: "Aysar Mohamed" <sip:[email protected]>;tag=37693~244641b0-36ac-434c-91c1-823f25a68b28-18299026
To: <sip:[email protected]>;tag=739628-1BDB
Date: Fri, 30 May 2014 20:19:34 GMT
Call-ID: [email protected]
CSeq: 101 INVITE
Allow-Events: telephone-event
Server: Cisco-SIPGateway/IOS-12.x
Reason: Q.850;cause=41
Content-Length: 0
May 30 20:19:34.684: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Received:
ACK sip:[email protected]:5060 SIP/2.0
Via: SIP/2.0/UDP 192.168.200.53:5060;branch=z9hG4bK3bd451bf17e0
From: "Aysar Mohamed" <sip:[email protected]>;tag=37693~244641b0-36ac-434c-91c1-823f25a68b28-18299026
To: <sip:[email protected]>;tag=739628-1BDB
Date: Fri, 30 May 2014 20:19:34 GMT
Call-ID: [email protected]
Max-Forwards: 70
CSeq: 101 ACK
Allow-Events: presence, kpml
Content-Length: 0
May 30 20:19:34.688: //465/B5A494800000/CCAPI/cc_api_call_disconnect_done:
Disposition=0, Interface=0x30CF41D4, Tag=0x0, Call Id=465,
Call Entry(Disconnect Cause=41, Voice Class Cause Code=0, Retry Count=0)
May 30 20:19:34.688: //465/B5A494800000/CCAPI/cc_api_call_disconnect_done:
Call Disconnect Event Sent
May 30 20:19:34.688: //-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
May 30 20:19:34.688: :cc_free_feature_vsa freeing 31A5DAD0
May 30 20:19:34.688: //-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
May 30 20:19:34.688: vsacount in free is 0
May 30 20:19:36.044: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Received:
OPTIONS sip:172.29.7.94:5060 SIP/2.0
Via: SIP/2.0/UDP 10.208.9.69:5060;branch=z9hG4bKmisco3ykfiooegpygsphkocp1T20326
Call-ID: isbcfemyk1p1mkteets1tcmi53eeehfhikcp@SoftX3000
From: <sip:172.29.7.94:5060>;tag=sbc0803k1pyk51o
To: <sip:172.29.7.94>
CSeq: 1 OPTIONS
Max-Forwards: 70
Content-Length: 0
May 30 20:19:36.048: //467/8DAABF6C8278/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 200 OK
Via: SIP/2.0/UDP 10.208.9.69:5060;branch=z9hG4bKmisco3ykfiooegpygsphkocp1T20326
From: <sip:172.29.7.94:5060>;tag=sbc0803k1pyk51o
To: <sip:172.29.7.94>;tag=739BBC-1CE2
Date: Fri, 30 May 2014 20:19:36 GMT
Call-ID: isbcfemyk1p1mkteets1tcmi53eeehfhikcp@SoftX3000
Server: Cisco-SIPGateway/IOS-12.x
CSeq: 1 OPTIONS
Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
Allow-Events: telephone-event
Accept: application/sdp
Supported: 100rel,timer,resource-priority,replaces,sdp-anat
Content-Type: application/sdp
Content-Length: 446
v=0
o=CiscoSystemsSIP-GW-UserAgent 3496 1601 IN IP4 172.29.7.94
s=SIP Call
c=IN IP4 172.29.7.94
t=0 0
m=audio 0 RTP/AVP 18 0 8 9 4 2 15
c=IN IP4 172.29.7.94
m=image 0 udptl t38
c=IN IP4 172.29.7.94
a=T38FaxVersion:0
a=T38MaxBitRate:9600
a=T38FaxFillBitRemoval:0
a=T38FaxTranscodingMMR:0
a=T38FaxTranscodingJBIG:0
a=T38FaxRateManagement:transferredTCF
a=T38FaxMaxBuffer:200
a=T38FaxMaxDatagram:320
a=T38FaxUdpEC:t38UDPRedundancy
My SIP GW internal ip address is 192.168.200.86
and the Public IP is : 172.29.7.94
My CUCM is 192.168.200.53
my GW Config is :
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
sip
registrar server
voice class codec 1
codec preference 1 g711alaw
codec preference 2 g711ulaw
codec preference 3 g729r8
codec preference 4 g729br8
voice translation-rule 3
rule 1 /^9\(\)/ /\1/
voice translation-rule 4
rule 4 /^22217/ /7/
rule 5 /^2217/ /7/
rule 6 /^022217/ /7/
rule 7 /^0122217/ /7/
voice translation-rule 5
rule 1 /^5/ /905/
rule 2 /^1/ /901/
rule 3 /^2/ /902/
rule 4 /^3/ /903/
rule 5 /^4/ /904/
rule 6 /^6/ /906/
rule 7 /^7/ /907/
rule 8 /^8/ /908/
rule 10 /^00/ /900/
rule 11 /'+'/ /900/
voice translation-profile OUT
translate called 3
voice translation-profile REDIAL
translate calling 5
voice translation-profile SIP-NEW
translate called 4
application
service mva http://192.168.200.53:8080/ccmivr/pages/IVRMainpage.vxml
service ccm http://192.168.200.53:8080/ccmivr/pages/IVRMainpage.vxml
license udi pid CISCO2921/K9 sn FCZ164960G0
hw-module pvdm 0/0
hw-module pvdm 0/1
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$
ip address 192.168.200.86 255.255.255.0
duplex auto
speed auto
interface GigabitEthernet0/1
ip address 172.29.7.94 255.255.255.252
duplex auto
speed auto
ip http server
ip http access-class 23
ip http authentication local
no ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip route 0.0.0.0 0.0.0.0 192.168.200.1
ip route 10.208.9.0 255.255.255.0 172.29.7.93
access-list 23 permit 10.10.10.0 0.0.0.7
control-plane
mgcp profile default
sccp local GigabitEthernet0/0
sccp ccm 192.168.200.53 identifier 1 priority 1 version 7.0
sccp
sccp ccm group 1
associate ccm 1 priority 1
associate profile 2 register NAGHI-MTP
dspfarm profile 2 mtp
codec g711alaw
maximum sessions hardware 25
associate application SCCP
dial-peer voice 802 voip
description ** SIP TO STC **
translation-profile outgoing OUT
destination-pattern 9T
session protocol sipv2
session target ipv4:10.208.9.69:5060
session transport udp
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay sip-notify rtp-nte sip-kpml
no vad
dial-peer voice 811 voip
description ** SIP INCOMING FROM STC **
translation-profile incoming SIP-NEW
translation-profile outgoing REDIAL
destination-pattern 7...
session protocol sipv2
session target ipv4:192.168.200.53
incoming called-number 022217...$
dtmf-relay sip-notify rtp-nte sip-kpml
codec g711alaw
dial-peer voice 812 voip
description ** SIP INCOMING FROM STC **
translation-profile incoming SIP-NEW
translation-profile outgoing REDIAL
destination-pattern 7...
session protocol sipv2
session target ipv4:192.168.200.53
incoming called-number 22217...$
dtmf-relay sip-notify rtp-nte sip-kpml
codec g711alaw
dial-peer voice 813 voip
description ** SIP INCOMING FROM STC **
translation-profile incoming SIP-NEW
translation-profile outgoing REDIAL
destination-pattern 7...
session protocol sipv2
session target ipv4:192.168.200.53
incoming called-number 2217...$
dtmf-relay sip-notify rtp-nte sip-kpml
codec g711alaw
dial-peer voice 814 voip
description ** SIP INCOMING FROM STC **
translation-profile incoming SIP-NEW
translation-profile outgoing REDIAL
preference 1
destination-pattern 7...
session protocol sipv2
session target ipv4:192.168.200.63
incoming called-number 022217...$
dtmf-relay sip-notify rtp-nte sip-kpml
codec g711alaw
dial-peer voice 815 voip
description ** SIP INCOMING FROM STC **
translation-profile incoming SIP-NEW
translation-profile outgoing REDIAL
preference 1
destination-pattern 7...
session protocol sipv2
session target ipv4:192.168.200.63
incoming called-number 22217...$
dtmf-relay sip-notify rtp-nte sip-kpml
codec g711alaw
dial-peer voice 816 voip
description ** SIP INCOMING FROM STC **
translation-profile incoming SIP-NEW
translation-profile outgoing REDIAL
preference 1
destination-pattern 7...
session protocol sipv2
session target ipv4:192.168.200.63
incoming called-number 2217...$
dtmf-relay sip-notify rtp-nte sip-kpml
codec g711alaw
dial-peer voice 817 voip
description ** SIP INCOMING FROM STC **
translation-profile incoming SIP-NEW
translation-profile outgoing REDIAL
destination-pattern 7...
session protocol sipv2
session target ipv4:192.168.200.53
incoming called-number 0122217...$
dtmf-relay sip-notify rtp-nte sip-kpml
codec g711alaw
dial-peer voice 818 voip
description ** SIP INCOMING FROM STC **
translation-profile incoming SIP-NEW
translation-profile outgoing REDIAL
preference 1
destination-pattern 7...
session protocol sipv2
session target ipv4:192.168.200.63
incoming called-number 0122217...$
dtmf-relay sip-notify rtp-nte sip-kpml
codec g711alaw
Please i need ur help ASAP -
Troubleshooting SS7 Interconnect for Voice Gateway
Hi
Recently we have implemeted SS7 Interconnect for Voice Gateway Solution in our network.
We are using devices PGW2200, NAS 5400, SLT 2611, 4000 Series S/w and GK.
Customers compalint that they are facing Echo, Clip in Voice and No voice related issues. Can you tell us the commands on PGW/GW/SLT to pinpoint. PGW we are using in Call Control Mode.
Please help.
Thanks in Advance.Hi,
You can check in the /opt/CiscoMGC/etc directory properties.dat file which has the parameter *.EchoCanRequired which should be set to 1. This can binded by an individual trunk-group as well. Also make sure the voice-ports have the echo-cancel coverage and disable VAD to see if it makes it better.
Regards
-Kashif -
Site to Site Connectivity Between BE6K and Voice Gateway 2901
Greetings,
Is an Ethernet handoff required for site to site connectivity between BE6K and a voice gateway 2901. My vendor is suggesting that it's required in order for both sites to see the BE6K as one phone system. However, here in lies the problem. I have a point-to-point T-1 between the sites that does not have an Ethernet handoff, just the smartjack to the T-1.
What would I need to get this to work? Have a router at each site? If so, which model? Or is there a component I could add to the BE6K or voice gateway?
Any help would be greatly appreciated.
Thanks in advance.Ethernet handoff just means that the provider will deliver the circuit using Ethernet. What circuit is your provider delivering for you? Do they manage your WAN? Like I said what you need is ip connectivity between your sites and BE6k. If your T1 connection provides WAN connectivity and you have ip connectivity between the sites, then I don't know what you need any handoff for. The question is do you have ip connectivity between the sites via your T1 connection
-
Voice Gateway & Gatekeeper On a single Router?
Hello All,
Has anyone had experience with putting voice gateway and voice gatekeeper functionality into one router? We will have three clusters initially (with about 1,000 users worldwide though) and was considering one gatekeeper per cluster for CAC and tail end hop off routing for LD/International calls.
Any guidance on what sort of platform these should be running on if kept separate? DSP resources in them, etc.?
The voice gateways will be a mixture of 2851 and 3800 series routers. Thanks in advance for the help.
Thanks,
DaveHi,
I have done this many times in lab, dont know if that will be ok in production if you have a good powerfull problem i dont think that it will be a problem.
About the DSP's maybe you can use the DSP calculator - anyway this refers to many parameters on the network.
BR,
Teo
Maybe you are looking for
-
Print servers for 30 client Mac Mini Lab
I have a 30 client Mac Mini lab with printing done by 2 networked HP Officejet 8600+ printers w/ 128mb memory. I would like to have a print server that will speed up the printing(kindergarteners can be impatient). A dozen years or so ago there were
-
Can I configure two webserver domain in one windows server
Can I configure two webserver domain in one windows server with default port. ( i.e 80 ) For Ex:- http://server-name/psp/DOMAIN/?cmd=login and another one http://server-name/psp/DOMAIN2/?cmd=login. If not please let me know the workaround to do so. B
-
Change Pick List Output Format with automated Output format froTO creation
hi., When creating TO for delivery using VL06P or LT03 there is no opportunity to print the Company Custom Format(X1) of the pick list. But if it is reprinted in LT31, Print Code X1(Company defined picking list Output format) can be selected. This i
-
Different MOH for Internal and External Calls
Is it possible to have a different MOH source for internal vs external calls. I know that Network MOH is for transfering but can this be used for external MOH source from the PSTN?
-
Hey all, I'm playing around with this project I have at work and I'm authoring a DVD for a local music group. I have an awesome layout already, but when I push the project to DVD the images are distorted. I have just been dragging them onto the menu