Voice Module for Cisco 2800

Hi, I am new to VoIP. I was wondering what hardware is needed to support toll bypass on a cisco 2800 router? I understand you need a Voice Network Modules and PVDM2, but which ones?
Thanks

Hi
You will need voice cards (e.g. VWICs or VICs) and PVDMs to support the number and type of codec calls you want to run.
You'll also need IOS with voice features...
REgards
Aaron
Please rate helpful posts...

Similar Messages

Gateway Module for CISCO 2800

Hi, I am new to VoIP. I was wondering what hardware is needed to support toll bypass on a cisco 2800 router? I understand you need a Voice Network Modules and PVDM2, but which ones?
Thanks

I am using analog phones connected to a nortel PBX. I am wondering which module to use to allow FXO and FXS interface.
thanks

SFP module for Cisco Router 7200

Hello, I have a router 7200. we have hired a ISP with a fiber cord. That fiber cord is connected to a tranciever taht convert fibre to copper and then copper is conected to a wan interface of router 7200. But Now we want to connect fiber directily, for taht reason we want to add a fiber module. What kind of fiber module can I use?

Hi victors0991,
I can help you look for the best fiber module to use and locate the best deal for your purchase please send me an email at [email protected] so we can discuss your inquiry further
hope to hear from you soon.

Cisco 2600 voice IP for FXO interface

Hi all,
Pls help me step by step configuring Voice IP for Cisco 2600 using FXO interface.
Thank you very much.

It all goes by what you want to cofigure. FXO interface generally connects with PBX or PSTN..
Some config examples using FXO ports, visit
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/inst_nts/acc_gtwy/voice.htm
One more good link on that
http://www.cisco.com/warp/public/788/signalling/fxo_disconnect.html

Related to vmic2-2mft-g703 module on Router 2800

I have purchased the vmic2-2mft-g703 for CISCO 2800 series router and want to know that can I configure this card two interfaces act as a simple data interfaces like router inbuilt ethernet interfaces? If yes then how? Please help me.

Hello Ganesh,
try to see if
conf t
controller e1 0/2/0
is supported it it looks like you need to go this way
see
http://www.cisco.com/en/US/products/hw/modules/ps2617/products_configuration_example09186a008052c920.shtml
if so you need to configure a channel-group
controller e1 0/2/0
no shut
channel-group 0 unframed
a serial interface is created
serial 0/2/0:0
verify with your provider if you need an unframed or all timeslots in a group config
Hope to help
Giuseppe

Can you Connect Cisco switch modules for to N2K?

I have not seen anything about connecting Cisco Switch modules for Blade Chassis to fex. Does anybody now if you can do that?
thank you.

thank you Lucien.
I think you got a right name for N2Ks, a NIC card extender. In my opion N2K should be able to support Blade switches. Not every company has just rack mount servers, most enviroment is mixed. In my case, I run out ports on N5K, but plenty available on N2K. I want add two more blade centers with gig switch modules in them. now I have to buy a N5K!!!. I'm sure Cisco can make N2K to support switches too.

Looking for Cisco 6500 E series 1/10 G SFP Module

I am looking for 24 ports 1/10G SFP module for my 6509E chassis and WS-SUP720-3B sup module.
I have found the following from my research
WS-X6704-10GE - 4 port 10G module which supports only 10G not 1G
WS-X6708-10G-3C - 8 Port 10G module which supports only 10G not 1G
WS-X6724-SFP - 24 Port 1G SFP module which supports only 1G not 10G
Thanks for your help

Hi datamodule, i see that you are looking for a 24 ports 1/10G SFP module for the Catalyst 6509E. From what i am looking at it's either 1G or 10G. Please check this link for further assistance: http://cs.co/9000YTBE. Feel free to message me for further assistance.
Thanks,
Angela ([email protected])

IP changes on a Cisco Switch Module for IBM BladeCenter

Hi everyone,
I was just wondering if anyone out there is using the MDS modules for IBM BladCenters and if so whether you had had any problems changing the IP details through the BladeCenter management interface. I needed to change a subnet mask but since making the change I've lost all IP connectivity to the module and it shows Status: Disabled under the new IP Details.
I've tried resetting the module to factory defaults and whilst this seems to have had some effect (e.g. the fc ports have all gone down) it has given me any IP connectivity or allowed me to set up a new IP address.
Has anyone else seen this and if so, how did you get round it.
Thanks,
David

Hi Mike,
I saw that it doesn't allow you to change any of the IP config through the CLI, hence why I moved on to trying the MM.
Fabric manager can't connect to the module on it's address (I was just correcting the subnet mask) and it is not pingable from anywhere on the network, so it seems to me that the IP path out through the MM isn't working.
I tried the same process on one of our test chassis and the same thing has happened there.
Configuration for that slot looks like this on the MM:
Bay 3 (Fibre SM)*
Current IP Configuration
Configuration method: Static
IP address: 172.20.221.9
Subnet mask: 255.255.255.0
Gateway address: 172.20.221.3
New Static IP Configuration
Status: Disabled
To change the IP configuration for this switch module, fill in the following
fields and click "Save". This will save and enable the new IP configuration.
IP address 172.20.221.9
Subnet mask 255.255.255.224
Gateway address 172.20.221.3
How does the MM communicate with the module (telnet/snmpv1/snmpv3/ssh?) and with what credentials. I'm thinking that there must be something in how we've configured the switches that is breaking this in some way (we've enabled aaa auth for login, removed some default SNMP details, and disabled the telnet server).
There seems to be rather a lack of docs on these modules, is there anywhere to find out more detail on how they all hang together.
Thanks for your interest and help,
David

Unity: Voice-mail for non-Exchange subscribers

Hi everyone!
I have this issue: customer wants to enable voice-mail for non-Exchange users, I've created them as Internet subscribers for using with auto attendant, but I can't enable voice-mail for these extensions, basically the customer does not want for this users to receive the messages in their mail just only check it on IP phones. Is there a possible way???
Thanks in advance for your help

To add to Hailey's comment, here's the documentation that explains the behavior/limitations of Internet Subscribers in case you're interested in checking it out:
http://www.cisco.com/en/US/docs/voice_ip_comm/unity/5x/networking/guide/ex/5xcunet040e.html#wp1050583
Hope that helps,
Brad

Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command

Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command
and I am getting an Error , I cant figure out what I am doing wrong. I have also pasted my display down here can someone help me out, thanks in advance, I am still new to this utility.
My questions are How do you direct this utility to point to the desktop or the TFTP folder
does FE_PORT: Fast Ethernet 0 imply or point to Fa0/0 on my router
My router is suppose to have 10.0.0.3 255.0.0.0
Gateway of 10.0.0.1 255.0.0.0
My TFTP Server 10.0.0.2 255.0.0.0
How do I get the MAC address of the Router or the TFTP Server and which one is required?
my Ethernet port is 100Mb/Sec I cant tell whether it is full duplex or not so How do i set this FE_SPEED_MODE: Auto???
=====================================================================================
rommon 10 >
rommon 10 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
?=0
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=
rommon 11 > TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
rommon 12 > TFTP_CHECKSUM=0
rommon 13 > SET
monitor: command "SET" not found
rommon 14 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
?=0
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
rommon 15 > tftpdnld
          IP_ADDRESS: 10.0.0.3
      IP_SUBNET_MASK: 255.0.0.0
     DEFAULT_GATEWAY: 10.0.0.1
         TFTP_SERVER: 10.0.0.2
           TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
        TFTP_MACADDR: 30:37:a6:49:35:a8
             FE_PORT: Fast Ethernet 0
       FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 16 >       " not found
rommon 17 >FE_SPEED_MODE=2
variable name contains illegal (non-printable) characters
rommon
rommon 18 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
?=0
rommon 19 > tftpdnld [ur]
usage: tftpdnld [-hr]
Use this command for disaster recovery only to recover an image via TFTP.
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
            IP_ADDRESS: The IP address for this unit
        IP_SUBNET_MASK: The subnet mask for this unit
       DEFAULT_GATEWAY: The default gateway for this unit
           TFTP_SERVER: The IP address of the server to fetch from
             TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
          TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
      TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=18)
          TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
         TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
          TFTP_MACADDR: The MAC address for this unit
               FE_PORT: 0= (default), 1
         FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx,
                        5=Auto (default)
      TFTP_DESTINATION: The flash destination device for the file
                        flash:(default), usbflash0:, usbflash1:
Command line options:
   -h: this help screen
   -r: do not write flash, load to DRAM only and launch image
rommon 20 > tftpdnld
          IP_ADDRESS: 10.0.0.3
      IP_SUBNET_MASK: 255.0.0.0
     DEFAULT_GATEWAY: 10.0.0.1
         TFTP_SERVER: 10.0.0.2
           TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
        TFTP_MACADDR: 30:37:a6:49:35:a8
             FE_PORT: Fast Ethernet 0
       FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 21 >

What I notice in the original post is this error
ARP: address resolution for 10.0.0.2 timed out.
which says that the router is looking for the 10.0.0.2 server but not getting response to its arp request. Can the original poster clarify for us how the device that has the image file is connected to the router that has the problem? Also what kind of device is 10.0.0.2? Is it a PC running TFTP server software or is it something else?
HTH
Rick

How Do I Configure A WRT54G to Work With A Cisco 2800 Router

I'm helping my dad set up a new network. He has a Cisco 2800 series router that connects to the internet via two T1 lines. From this connection, he supplies internet service to his customers. The router was installed and configured with help from AT&T who monitors the router and advises my dad if there are problems.
The Cisco 2800 is not my reason for posting.
He wants to connect his home computers to the 2800. He has one desktop and two wireless laptops and wants to use a WRT54G to connect those computers to the 2800 router. How should he configure the WRT54G to connect to the 2800?
Thanks!

That's what I thought. So it is really no different than connecting the WRT to a DSL modem or cable modem as far as the setup goes. Good then.
Now, next question;
Would this network setup be correct?
Connect a 5-port switch to the 2800
Connect the WRT54G to the 5-port switch.
Configure the laptops to connect throught the WRT54G.
Connect the desktop (Ubuntu 9.10) to the 5-port switch via Ethernet cable (bypass the WRT54G).
Would there be IP conflicts or domain problems? I ask this because this is how his LAN is presently setup and he seems to be getting random connectivity problems on his Ubuntu desktop machine. One day it works fine. The next day it won't connect. Sometimes, even after he is connected, it stop works midstream. It also takes 10 minutes or so to boot up. The laptops always work without issue.
The two laptops would be issued IP addresses of 192.168.1.xxx but the desktop would be getting 12.83.xxxx.xx(something similar). The desktop's internet IP would receive its internet IP from the 2800 via DHCP just like the WRT54G is receiving its IP from the 2800. The two would essentially be on different LANs connected to the same router. Do you forsee any issues here?
Thanks!

I can't retrieve usm and vacm tables from router cisco 2800. Help please!!

Hi, I'm doing some tests in a router cisco 2800 using snmp in versions 2c and 3. I configured views and communities for version 2c and user, groups and views for version3; I suppose that the vacm and usm parameters involved in the groups, views are stored internally in usm, vacm tables. I wanted to check if the parameters I configured were inside the tables, but when I tried to retrieve all those values through get table or get next commands, I obtained the answer "end of mib view" in the application I'm using (SNMP J MANAGER) and also in wireshark where the requests are sent but the responses contain the OIDs belonging to the tables but with the value end of mib view.
I know for experience doing the tests, that "end of mib view" is obtained in a response when you try to request a OID that is outside of the view being used by a community. But the last thing I did was create a community related to a view with access to internet included. Later, I used that community (comlectura) in version 2c to retrieve those values of usmtable (1.3.6.1.6.3.15.1.2.2 ) and vacmtable (inside of 1.3.6.1.6.3.16.1) and nothing.
These are some commands I configured in the router:
snmp-server group readonly v3 auth read readview
snmp-server group writeonly v3 auth write writeview
snmp-server view readview internet included
snmp-server view writeview internet included
snmp-server view viewcomlectura mib-2 included
snmp-server view viewcomlectura2 system included
snmp-server community comlectura view readview RO
snmp-server community comlectura2 view viewcomlectura2 RO
snmp-server trap-source FastEthernet0/1
I think the cause of this error perhaps is because these tables don't exist in the CISCO MIB, but I don't thinks cisco devices ONLY have cisco mibs (
1.3.6.1.4.1.9) inside of them, because I can make request with OIDs of mib-2 branches. Anyway, please someone that can guide me in this problem. Thanks in advance.

You cannot use Mavericks. Ask a friend who still runs windows or any Mac OS except Mavericks to bring their laptop and help you out.
Or plug in a USB drive for instance and create a bootable version of any previous version of OSX since 10.5.x -10.8 all of which will work fine.
Or dual boot to windows where the latest airport utility is still 5.6

Setting up a Test Voice VLAN for Lync 2013

I want to set up a second voice vlan to be a test vlan.
In the current situation the customer has voice and data running on vlan1. The customer insist on taking incremental steps to improve QoS. I have advocated separated vlans for voice and data. They just want to move everything (phase 1) to a different
vlan. They want to see how getting all traffic of vlan 1 will improve there performance. Again, I recommended the best practice, they want to try this approach first.
I am conducting a pilot test with just one cx600 IP phone. and a single switchport. I created a new vlan99 using VTP. I configured the switchports on the Cisco 2960-x switch as follows.
#switchport mode access
#switchport access vlan 99
The phone gets its correct vlan id, and pulls its IP from the correct dhcp scope. However the phone displays "connecting with the lync server" for a long time, then "connecting to download its certificates". This takes a long time then fails.
If I change the switchport back to vlan1 it works fine. What can be the problem? Does the vlan99 need to be defined on the lync server? How many vlans can be supported by Lync 2013?
Thank you,
gigiu

Did you set the VLAN Configuration for Lync Phone Edition?
You can check the following links:
http://blog.schertz.name/2011/01/manual-vlan-configuration-for-lync-phone-edition/
http://www.bricomp.com/blogs/post.cfm/dedicated-voice-vlan-for-lync-devices
Note: Microsoft is providing this information as a convenience to you. The sites are not controlled by Microsoft. Microsoft cannot make any representations regarding the quality, safety, or suitability of any software or information found there. Please
make sure that you completely understand the risk before retrieving any suggestions from the above link.
Lisa Zheng
TechNet Community Support

Content Engine Network Module for Caching File Server Objects

We have a content engine network module for a 2821 router located at a branch office that we'd like to use for clients to obtain locally cached file objects from a Windos server located at our headquarters or corporate office. I've been looking for some sample configs or documentation that will show me that this is possible and on how to do it since this is my first time ever doing. All I was able to find so far was the link below under "Support of Preloading of NTLM Authenticated Objects", but it seems incomplete in providing configuration tasks that most CCO doc's usually provide. Has anyone else had any luck finding some useful doc's or sample configs to get this accomplish? Thanks in advance.
http://www.cisco.com/univercd/cc/td/doc/product/webscale/uce/acns55/55ldg/urlfiltr.htm#wp1158213

You can't cache Windows Files using the Cache Engines.
You CAN do this using WAFS though. I'd suggest looking at the WAFS (or upcoming WAAS) products, which use WCCP like the Cache Engines to transparently redirect Windows File Sharing requests.

Spa112 voice module is not ready

What can cause the "voice module is not ready" message in the spa112? I keep getting that on multiple spa112's while provisioning them. We are provisioning via TFTP and upgrading the firmware to 1.2.1 as part of the config. I have 2 files being downloaded, a general config for every device then a mac specific one with the two phone numbers. What I am seeing is the two files are being downloaded but the 112 still shows the old firmware.
They often sit in this state for an hour or more before we reboot them. After multiple reboots they will finally grab the firmware but sometimes still stay in this state.

I will try those steps next time I see the issue. On the ones I was seeing it I was getting times much more than 90 seconds, several hours infact
The config I am using is based on the 1.1 syntax.
Are you suggesting I do the following
have spa112.cfg only have a the following
http://10.10.10.10/spa/firmware/112/SPA112_SPA122_1.2.1_FW.bin
tftp://10.10.10.10/spa112-121.cfg
and then have
tftp://10.10.10.10/spa112-121.cfg be my main config?
Also I do often use the debug to confirm that my file is being applied. So I can see its being downloaded to the device, and that provisioning is being accepted
Is there a way make the spa112 not do anything until it has upgraded the firmware? What I see currently is that it gets its full config, both profile_rule and profile_rule_a sets its config, then updates firmware to 1.1.0 I want every one to do firmwre first and check to see if the firmware is at 1.1.0 before it downloads the config.

Voice Module for Cisco 2800

Similar Messages

Maybe you are looking for