Voice over Frame with FXS

I have two branch routers connected to central site over frame relay network.
Now i've put fxs cards in all three routers and want voice connectivity among all three routers.
Basically its like hub and spoke.. one central site connecting on sub-interface to two other sites on frame network.
What is the best way to configure these three routers ???
please advice

Your requirements seem vey simple so my suggestion is to keep the configuration very simple as well. You need a dialplan which allows each site to call the other two sites.
I would suggest you use voice over ip OVER frame, rather than just voice over frame. There is a little bit more overhead, but ease of troubleshooting and configuration makes it worth it.
You need two voip dial peers at most to differntiate what destination patterns go to which site and one pots dial peer for each FXS port that you have a phone attached to.
For QOS, i suggest using frame relay traffic shaping and if necessary LLQ.
Hope this answers your question.

Similar Messages

  • Voice over Wireless with Cisco phones 7921 and 7925

    Hello experts,
    I made an wireless audit for a company.
    They have 2 WLCs 5508 in HA mode, with APs 2602 for indoor and 1552. Version of the WLC : 7.6.120.0
    At the end of the day we noticed that the roaming between indoor and outdoor access points is sometimes failing and results to a complete disconnection of the wireless phone (7921 or 7925) from the network. When people go from the indoor to the outdoor area, there is no problem. The problem comes when people are coming from the outdoor to the indoor.
    Also, on the WLC, the power lvl of the outdoor APs are set to 1 ... Is it good or not ?
    My question is, is there any known issue about Voice over wireless with WLC 5508-7.6.120.0 with APs 2602 and 1552 ?
    Maybe it should be better to upgrade to 7.6.130.0 ?
    Thanks in advance,
    Alexis

    Normally yes.
    Is there a way to troubleshoot what's going on with the phones ? Maybe a "show client detail MAC address* on the WLC ?
    Here are some logs when the phones are losing the network :
    *Dot1x_NW_MsgTask_4: Apr 09 12:44:21.320: #DOT1X-3-INVALID_WPA_KEY_MSG_STATE: 1x_eapkey.c:957 Received invalid EAPOL-key M2 msg in START  state - invalid secure bit; KeyLen 40, Key type 1, client 00:24:d7:83:56:dc
    *apfMsConnTask_6: Apr 09 12:28:32.668: #APF-3-VALIDATE_CCKM_REASS_REQ_ELEMENT: apf_utils.c:2506 Could not validate the CCKM Reassociation request element.Received Timestamp deviation > 1sec in CCKM Info Element from mobile. Mobile:4c:00:82:85:6e:e1,  AP:1
    *Dot1x_NW_MsgTask_1: Apr 09 12:26:53.964: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 74:26:ac:63:8c:a9 - got 00 00 00 00 00 00 00 03, expected 00 00 00 00 00 00 00 04
    *Dot1x_NW_MsgTask_1: Apr 09 12:26:53.929: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 74:26:ac:63:8c:a9 - got 00 00 00 00 00 00 00 02, expected 00 00 00 00 00 00 00 04
    *apfMsConnTask_4: Apr 09 12:24:34.959: #APF-3-VALIDATE_CCKM_REASS_REQ_ELEMENT: apf_utils.c:2506 Could not validate the CCKM Reassociation request element.Received Timestamp deviation > 1sec in CCKM Info Element from mobile. Mobile:78:da:6e:f6:5f:89,  AP:5
    *Dot1x_NW_MsgTask_0: Apr 09 12:22:30.217: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 4c:00:82:85:1d:68 - got 00 00 00 00 00 00 00 03, expected 00 00 00 00 00 00 00 04
    *Dot1x_NW_MsgTask_4: Apr 09 12:22:30.206: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 4c:00:82:85:b3:ac - got 00 00 00 00 00 00 00 03, expected 00 00 00 00 00 00 00 04
    *Dot1x_NW_MsgTask_4: Apr 09 12:22:30.186: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 4c:00:82:85:b3:ac - got 00 00 00 00 00 00 00 02, expected 00 00 00 00 00 00 00 04
    *Dot1x_NW_MsgTask_0: Apr 09 12:22:30.167: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 4c:00:82:85:1d:68 - got 00 00 00 00 00 00 00 02, expected 00 00 00 00 00 00 00 04
    *Dot1x_NW_MsgTask_6: Apr 09 12:22:29.672: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 78:da:6e:f6:14:2e - got 00 00 00 00 00 00 00 03, expected 00 00 00 00 00 00 00 04
    *Dot1x_NW_MsgTask_6: Apr 09 12:22:29.638: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 78:da:6e:f6:14:2e - got 00 00 00 00 00 00 00 02, expected 00 00 00 00 00 00 00 04
    *apfMsConnTask_3: Apr 09 12:19:22.098: #APF-3-VALIDATE_CCKM_REASS_REQ_ELEMENT: apf_utils.c:2506 Could not validate the CCKM Reassociation request element.Received Timestamp deviation > 1sec in CCKM Info Element from mobile. Mobile:4c:00:82:85:6e:e1,  AP:5
    *osapiBsnTimer: Apr 09 12:13:36.031: #LOG-3-Q_IND: spam_lrad.c:53542 The system is unable to find WLAN 2 to be deleted

  • Voice over Frame-Relay

    Hi,
    Customer of me has several sites connected with leased lines. The leased lines have frame-relay encapsulation (frame-relay back-to-back)
    The line has two pvc's configured, one for voice and one for data. The voice PVC works fine. On the data pvc we want to put some QoS.
    Here is the partial configuration:
    interface Serial0
    bandwidth 2000
    no ip address
    encapsulation frame-relay
    no ip route-cache cef
    ip route-cache flow
    no ip mroute-cache
    frame-relay intf-type dce
    interface Serial0.1 point-to-point
    ip address 10.xx.xx.1 255.255.255.252
    no ip mroute-cache
    frame-relay interface-dlci 120
    interface Serial0.2 point-to-point
    ip address 10.0.0.1 255.255.255.252
    no ip mroute-cache
    frame-relay interface-dlci 100
    class VOICE
    vofr cisco
    map-class frame-relay VOICE
    frame-relay cir 512000
    frame-relay voice bandwidth 256000
    frame-relay fragment 320
    frame-relay fair-queue
    Question is can I just apply a service policy out to the data DLCI or doi i also have to enable frame-relay traffic shaping?
    Thanks,
    JH

    The disadvantage of shaping is that it will actually limit you bandwidth. That is, you won't be able to use the circuit at full capacity, because of the artificial limitation induced by shaping. This is particularly true for a situation like you where the actual circuits is a leased line, and not a FR network.
    A better approach would be to reconfigure for simple hdlc encap, and run VoIP instead. This way, you would have all the QOS features you need for voice and data, and be able to use the full capacity with a much simpler configuration.
    Actually, even if you want to retain the FR encapsulation and the voice over FR approach, still using a single PVC would be better, for the same reasons given above.
    Hope this helps, please rate post if it does!

  • No Levels in Voice Over Meter with Presonus Firebox Preamp

    I've searched a bit through this forum and it seems this has been a problem in the past for several people. Has anyone figured out why the Presonus Firebox Preamp (using a condenser mic with phantom power)will register sound in Garage Band...Soundtrack Pro...etc, but not in Final Cut Pro 5.
    Final Cut Pro's VO utility identifies the Presonus Firebox, but no sound comes through at all...even if you try to record...say a few lines...and then play it back...still absolutely silent.
    Help!!!
    Mr. Pants

    Check that the sample rate is set the same everywhere:
    Presonus dialog
    Audio MiIDI setup
    Sequence settings
    Audio/Video settings- A/V Devices - Playback Output - Options
    and finally, Toolbench Voice Over dialog.

  • Ipod 4th Gen Shuffle - voice over prob with podcasts

    Hi. I have TWO of these cute little shuffles and I really like them.
    The problem is that each lives with its OWN Mac, each with its own install of itunes on the mac and BOTH OF THEM will refuse to say some of the PODCAST names.
    So for example in the computery voice when I press and hold the voice over button it will say:
    ABOVE AND BEYOND TRANCE AROUND THE WORLD
    then "Podcast 2" instead  of "The Dave Ramsey Pocast
    Then For mac eyes only
    Then "podcast 4" instead of "Tiestos club life".
    It doesn't seem to matter how many podcast episodes are in each major podcast label or whether I have started listening to the podcast or if its "unplayed".
    I have both of the shuffles set to "sync all podcasts" because I only have a few podcasts and there is always room..
    It seems sort of random.
    Any thoughts?

    SOLVED! The person who posted in another  message to voice over not working with all podcasts got it right and it worked
    So you go to   SUMMARY tab when clicking on your ipod , unclick voice over, click APPLY. Then click voice over then click APPLY. Then it all works!
    Re: Voiceover not working with all podcasts 
    May 15, 2011 11:51 PM (in response to jessicafromclitherall)
    sanfranciscotx was the person who gave this anser.
    You need to go to the Shuffle settings page, disable Voiceover, apply settings, the re-enable Voiceover to reset the spoken data.

  • Can I get the voice over Bluetooth with Google Map on WEBOS 2.0 (Palm Pre 2)?

    Hi,
    I just got a Palm Pre 2 with WEBOS 2.0, I am wondering if there is a setup or an application that can provide/enable the GPS voice over bluetooth when using the direction from the Google Map?
    Post relates to: Pre 2 p102una (Rogers)

    Hello Danmtl,
    If what you are referring to is being able to use a Bluetooth headset for Google Maps voice navigation, then you're in for disappointment. Google Maps w/ Navigation is only available for Android devices at this point in time, although there are talks of Google allowing the service to be placed on Windows Phone 7. As for the WebOS lineup, your only options for voice navigation would be either Verizon's VZ Navigator or Spint's Sprint Navigation. Either of those would require that you had purchased the phone specifically from that provider, so no luck for you there.
    Looks like we're all waiting on Google to step in for us at this point in time!

  • Is mac voice over compatilbe with pro tools 10?

    I have a new 17inch macbook pro with Liion, and I just purchased adn installed Avid Pro Tools 10.  I'm wondering if Voice Over is compatible with Pro Tools 10.

    Welcome to Apple Discussions!
    If your Mac shipped with 10.5.2, no.
    If your Mac shipped with an older operating system, it depends.
    According to http://www.digidesign.com/ you need a Mac with Tiger to run Protools LE. Check with them which version of Tiger it will work with.
    Then check this article to see if your Mac can run that version of Tiger:
    http://docs.info.apple.com/article.html?artnum=303315
    http://docs.info.apple.com/article.html?artnum=25517
    If it can't, sell your Mac, and get a used or refurbished one which can.
    Once you know your Mac can run that version of Tiger, if it is an Intel Mac, make sure you have the original Tiger installer which shipped with the Mac, as the retail Tiger installer will not work on the Intel Macs. Once you have discovered which version of Tiger works, backup your data at least twice*:
    http://www.macmaps.com/backup.html
    and Erase and Install Tiger on your Mac. Archive and Installing Tiger over Leopard does not work. Your other option is to get a Firewire external hard drive and install Tiger on that. http://www.macsales.com/ sells such hard drives. You can also partition your existing hard drive to have both Tiger and Leopard on it by erasing it with your Leopard Disk Utility and using its Partition function when booted off the Leopard installer, and selecting Disk Utility from the Utilities menu of the Leopard installer. Restore your documents to your hard drive from the backup when done. Applications may need to be reinstalled after an erase and install using the registration codes of the said applications.
    See my FAQ* here on how to buy used and refurbished Macs:
    http://www.macmaps.com/usedrefurbished.html
    And in the future always check the compatibility of the software you need before upgrading your operating system.
    - * Links to my pages may give me compensation.

  • Sending voice over UDP with JavaSound

    Hello,
    do anybody know how to send voice over UDP?. I have .wav files and I want to send them over UDP. If you have an example of this, send me it please. All the examples that I have seen only send one or to lines of text, but I need to know if I should convert the frames to bytes to be sent.
    Thank your help

    Hello,
    do anybody know how to send voice over UDP?. I have .wav files and I want to send them over UDP. If you have an example of this, send me it please. All the examples that I have seen only send one or to lines of text, but I need to know if I should convert the frames to bytes to be sent.
    Thank your help

  • I'm trying to trigger voice over audio with markers in a Edge timeline.

    I’m working on 4 instructional videos.
    Audio was not part of the initial plan, but it is now.
    Here’s the current edge video: http://docs.smoke51.com/Social/email/setup/web/
    I’m trying to sync the audio to the sections of the instructional video.
    There are 5 sections in the video; each can be triggered by a click. The play and pause buttons also work.

    on the button element that you use to pause the animation, you can have the audio pause as well.
    you might try something like the following:
    var myaudio = new Audio();
    myaudio.src = 'narration.wav';
    myaudio.pause();
    or with an audio tag such as <audio id="soundfile">, you can use:
    myaudio = $('soundfile');
    myaudio.pause();
    for the timeline, you can use sym.stop();
    that way, when one pauses, the other one does also.
    to autostart, set a trigger at 0ms on your timeline, then in the editor, put:
    var myaudio = new Audio();
    myaudio.src = 'narration.wav';
    myaudio.play();
    hope this helps.

  • Adobe Edge -  How to voice over syncing with time-line animation in adobe edge ?

    Hi ,
    I have created e-learning animation demo in using edge animate tool.
    I want to add voiceover  in this demo & functionality (play/ pause button, sound on/off)
    Regards
    Susanta Kumar Muduli

    This has worked for me inserted into a click event:
    var newSound = new Audio();
            newSound.src = "music.mp3";
            newSound.volume = 0.5;
            newSound.play();
    In a browser I have gotten it to play automatically, but on my  stupidphone I have to click on something.
    from Edge Animate JavaScript Docs - on Help Menu: Look at the example they cite
    bindTimelineAction
    Symbol.bindTimelineAction ( compId, symbolName, timelineName, eventName,actionFunction )
    compId - The composition ID, passed through the project-level closure. For example, "EDGE-519469".
    symbolName - The symbol ID, passed through the symbol closure.
    timelineName - The timeline name.
    eventName - The event. For example, click.
    actionFunction - The JavaScript function that executes when the trigger action fires. For stop, complete, and play events, the action function takes no arguments. For update events, the argument is elapsed. the milliseconds elapsed since the start of the timeline's playing.
    Description: Defines a function that executes when the specified timeline event is triggered.
    Example:
    Symbol.bindTimelineAction(compId, symbolName, "Default Timeline", "play", function(sym, e) {   
    var adobesound=new Audio();   
    adobesound.src="sound/SleepAway.mp3";   
    sym.setVariable("adobesound", adobesound);   
    this.getSymbol("volplus").stop(0);   
    this.getSymbol("volminus").stop(0);   
    adobesound.volume=0.1;    
    $(adobesound).bind("ended",function(){
    adobesound.play();
    Good luck
    Bob

  • Working with voice over and a Blackmagic Multibridge Eclipse

    I cant make the voice over work with my Blackmagic. I've tried with my M-Audio but I get the same result... No audio in voice over. The only way I can record is if I use Soundtrack.
    Can anyone help me?
    Thanks

    so many options here but to start with basics:
    using Firewire:
    mic > XLR cable > XLR mic input of mixer > Firewire out of mixer > Firewire Input of Mac
    using Decklink:
    mic > XLR cable > XLR mic input of mixer > balanced output of mixer > balanced line in of Decklink
    the mixer must have a mic input, which has an internal preamp, a line level input is no use; you need some thing like this ?
    link: [M-Audio front|http://www.m-audio.com/images/global/mediahqpics/FWSolo-frontRGB.jpg]
    link: [M-Audio back|http://www.m-audio.com/images/global/mediahqpics/fwsolo-backrgb.jpg]

  • Screencasting with audio voice over, how?

    I want to use QT to create a screencast tutorial, but need it to record my voice, too. Any way to do that with the free or pro version? (Using OS 10.6)

    Found a post that could help
    Re: Adobe Edge - How to voice over syncing with time-line animation in adobe edge ?
    Thanks,
    Preran

  • Unlisted error on voice over fr router

    I am getting the following log messages daily on 2 routers running voice over frame (not quite the right group I know...) - I cannot find any references anywhere on the Cisco website.
    Does anyone know what they mean & what is causing them ?
    Thanks for any replys........
    *Mar 6 07:40:03.133: convert_redirect_ocn_IE: illegal ieID passedencode_redirect_ocn_IE: invalid ieID! (ours: 1, peer's:6) Call should continue ... (ours: 1, peer's:6) Call should continue ... (ours: 1, peer's:6) Call should continue ... (ours: 1, peer's:6) Call should continue ... (ours: 1, peer's:6) Call should continue ...
    *Mar 6 08:07:27.366: convert_redirect_ocn_IE: illegal ieID passedencode_redirect_ocn_IE: invalid ieID! (ours: 1, peer's:6) Call should continue ... (ours: 1, peer's:6) Call should continue ... (ours: 1, peer's:6) Call should continue ...
    *Mar 6 08:17:04.613: convert_redirect_ocn_IE: illegal ieID passedencode_redirect_ocn_IE: invalid ieID! (ours: 1, peer's:6) Call should continue ... (ours: 1, peer's:6) Call should continue ... (ours: 1, peer's:6) Call should continue ...
    *Mar 6 08:40:46.535: convert_redirect_ocn_IE: illegal ieID passedencode_redirect_ocn_IE: invalid ieID! (ours: 1, peer's:6) Call should continue ... (ours: 1, peer's:6) Call should continue ... (ours: 1, peer's:6) Call should continue ... (ours: 1, peer's:6) Call should continue ...
    *Mar 6 09:10:26.846: convert_redirect_ocn_IE: illegal ieID passedencode_redirect_ocn_IE: invalid ieID!
    *Mar 6 09:13:43.037: convert_redirect_ocn_IE: illegal ieID passedencode_redirect_ocn_IE: invalid ieID! (ours: 1, peer's:6) Call should continue ... (ours: 1, peer's:6) Call should continue ...
    *Mar 6 09:18:20.175: convert_redirect_ocn_IE: illegal ieID passedencode_redirect_ocn_IE: invalid ieID! (ours: 1, peer's:6) Call should continue ...
    *Mar 6 09:32:30.279: convert_redirect_ocn_IE: illegal ieID passedencode_redirect_ocn_IE: invalid ieID!

    Thanks for that !!
    And apologies again for posting in the wrong group (I read it as "voice over IP"!!)

  • Audio voice over syncing

    Has anyone tried to do audio syncing like voice over an animation with EA CC 2014? Using the timeline I was able to embed a voice over in the browser and seems to work very well. I created a symbol with voice over and have an instance created with createChildSymbol() method from another symbol. At times, however, the audio is delayed and throws off the timing. I'm not sure how to solve this problem. Has anyone notice this?

    Found a post that could help
    Re: Adobe Edge - How to voice over syncing with time-line animation in adobe edge ?
    Thanks,
    Preran

  • Voice Over and Word 2004

    List members:
    I can't get Voice Over to read text written in Microsoft Word 2004 for the Mac. Will Voice Over function with all word processors, or is it limited to Text Edit? Thanks for any info.
    Mark Pavlick

    In fact, though it's quite unpretentious, TextEdit is quite a powerful little beast. If you have a Word 2004 document already, you can not only open and read it in TextEdit, you can modify it extensively, and the formatting will be preserved unchanged—text colour, font, bold/italic effects and so on. My totally blind VoiceOver-using wife translates Word documents from French into English, so the whole text is replaced by other words. When I open them in Word again, they're identical except for the language being different.
    TextEdit can also save new documents in Word or Word XML formats if you want, as well as plain text, HTML and RTF.
    Don't despair! (But I agree with Bruce—Pages is a terrible disappointment!)
    Archie

Maybe you are looking for