Voice over ip configuration between 2600 and 1700 routers

Hi,
I have the following set up:
2 offices with full T1 to the internet; one using a cisco 2600 router with FXS cards and the other using a 1700 router with FXS cards as well. I was asked to configure VOIP between the two sites and the PBX tech gave me at each office trunks which I connected to the FXS interfaces. The goal will be that the PBX guy be able to program the PBX with extension numbers of his choice and get the calls between the offices using the internet connection. I do not have a lot of experience setting up VOIP and I wonder if someone out there might have a similar environment.
According to the PBX tech, this trunk lines are loop start.
Thanks in advance for any ideas,
Uriel Naranjo.

It should be fairly straight forward. On the 2600 you will need to configure a voip dial-peer pointing to the remote site and pots dial peer to terminate a call on to the 2600 and you do the same on the 1700.
Check out the sample configurations on the following URL:
http://www.cisco.com/en/US/products/sw/iosswrel/ps1828/products_configuration_guide_chapter09186a00800ca621.html#5593
disregard the rsvp portion and just simply configure your routers to pass voip traffic. You can do QoS later depending on the load and traffic.

Similar Messages

  • I switched on the voice over at its minimum rate and now i am not able to slide the screen and unlock it, i switched on the voice over in ipad 2 ios 6 at its minimum rate and now i am not able to slide the screen and unlock it

    i switched on the voice over at its minimum rate and now i am not able to slide the screen and unlock it, i switched on the voice over in ipad 2 ios 6 at its minimum rate and now i am not able to slide the screen and unlock it  please advise

    You should be able to turn it off on the iPad by using 'a tap-to-select and then double-tap to activate/type process' and 3 fingered scrolling to go into Settings > General > Accessibility and turn it 'off' (so to use the 'slide to unlock' tap the slider and then double-tap it, and to type your passcode tap a digit and then double-tap it etc), or you can do it by connecting to your computer's iTunes : http://support.apple.com/kb/HT4064

  • My ipod shuffle 4th gen bought today and the voice over works for naming playlist and battery percent but wont name song and artist can anyone help also is the voice over button meant to be soft when pushed ?

    my ipod shuffle 4th gen bought today and the voice over works for naming playlist and battery percent but wont name song and artist can anyone help also is the voice over button meant to be soft when pushed ?
    thanks

    This document explains setting up and using VoiceOver.
    http://support.apple.com/kb/ht4322
    The overall settings for VoiceOver is on the shuffle's Summary screen in iTunes.
    Artist name and song name - Press and release the VoiceOver button. 
    The playlist menu - Press and hold the VoiceOver button.

  • I tried to turn off the voice over thing on my iphone and now the screen is completely dark i don't know what to do now

    i tried to turn off the voice over thing on my iphone and now the screen is completely dark i don't know what to do now...help! ima go crazy without out my phone

    ok so this is what i did i finally got it to work...so i taped the black screen with 3 fingers and then it went back to normal and it ****** me off because i had tryed that already so when it goes back to normal even if the voice over is still on it is easy to turn it off if you follow the steps....lol i googled how to turn off voice over so google it

  • Load balance between DLSw and CIP routers

    Take a look on this environment:
    - 4 routers receiving all DLSw peers and circuits
    - 4 routers with CIP boards connected to 2 mainframes
    All CIP routers are configured with same MAC address. All routers (DLSw and CIP) are connected on a Ethernet LAN switching, so this traffic are pure LLC2.
    How I can balance the traffic between DLSw and CIP routers ?
    Thank's in advance.

    I am not sure if I totally understand the topology. Let me rephrase it. Please correct me if I misunderstand the topology. In a data centre, there are 4 DLSw routers terminating DLSw peer connections from the remote sites. In the same data centre, there are 4 CIP routers which connects to 2 mainframes. CSNA is configured on all CIP router, which uses the same MAC. You configure transparent bridging on the DLSw routers, which connect to the same ethernet switches as the CIP routers. You configure SR/TLB on the CIP routers; so that all LLC2 circuits coming from the DLSw routers connect through the ethernet interfaces of the CIP routers.
    Do you want the LLC2 circuits from a DLSw router load balance across 4 CIP routers? As duplicate MAC address is not allowed, there is no way to connect all 4 DLSw routers and CIP 4 routers on the same VLAN.
    I can think of a couple of workarounds.
    1. Enable SNASw on the 4 DLSw routers. Create a VDLC port on all 4 DLSw routers. The MAC address of the VDLC interface is the same. The VDLC MAC address is pointed by the remote SNA stations. Each DLSw router uses one of the CIP routers as DLUS.
    2. If this is the case, create 4 VLANs on the ethernet switches. Connect a pair of DLSw router and CIP router to each VLAN.

  • ESS/MSS sso configure between java and abap instance

    Dear Gurus,
    I want to configure sso between java and abap instance for ESS/MSS. I couldnt find any guide for it, could you please help me gurus ?
    Other question is, is there any specific role for ESS/MSS users in JAVA instance. I want to create users and assign this role to them.
    Best Regards

    Hi Kemal,
    Hope you are doing good.
    There should be a / in the ITS path before SAP.
    Basically the entry that you have mentioned here should be accessible via browser as well. For eg in your case:
    http://<its hist name>/sap/bc/gui/sap/its/webgui should be accessible over browser.
    I also think you have put in a extra space in "w  ebgui". It should be "webgui".
    If the connector settings are working, then we can be sure that system connection is fine. You do not need to configure ITS settings.
    Also for SSO, refer the SAP note:1083421 and configure the SS0 settings again.
    Please run the SSO2 wizard and then make the automatic connection to
    the abap server. This will solve any inconsistencies on the server
    due to manual interventions.
    Most likely reason for the error is that certificates were loaded
    manually rather than using SSO wizard.
    More help:
    <http://wiki.sdn.sap.com/wiki/display/EP/Troubleshooting+SSO+between+AS-ABAP+and+AS-JAVA>
    The SSO enabling parameters should be set on the R/3 server.
    SSO Logon Ticket-> login/accept_sso2_ticket and login/create_sso2_ticket
    More info:
    <http://help.sap.com/saphelp_nw04/Helpdata/EN/22/41c43ac23cef2fe10000000a114084/frameset.htm>
    Thank you and have a nice day :).
    Kind Regards,
    Hemanth
    SAP AGS

  • Recording Voice-Over via Final Cut Pro and Recording Via Pro Tools?

    Hey all,
    I'm recording some voice-over for a documentary shot on DV.
    Here's my question: all other factors being the same, is there any disadvantage in terms of audio quality of recording into Final Cut (through an m-box2) using the voice-over tool, or recording into M-Powered Pro Tools using the mbox 2 (and then bringing the file to Final Cut)?
    Pro Tools obviously allows for a far more sophisticated treatment of the sound after it has been imputed - but in terms of using it for capture?
    I know that Pro tools allows 24bit recording, but I'd probably record at 16bit anyway so as to match the sample rate of the rest of my audio in the project.
    I'd be using the same mic-xlr-mbox2 set-up and the same computer, does anyone have any views on the difference in the quality of the recorded audio?
    Thanks
    Richard O'Sullivan
    San Francisco

    actually an in point by itself won't help you
    a valid recording range needs both In and Out point, or simply a clip in the timeline which by its presence denotes the recording range
    the recording range must be less than 5 minutes
    in a blank timeline some like to throw a slug in there to mark the recording range, i find it easiest to just enter a duration in the canvas (i type 4.. in the duration field at top left of the canvas and it automatically marks a 4 minute range)

  • ALE configuration Between HR and FI system

    Dear All,
    We have HR system on ECC6 and FI system on 4.x version,
    i have to do ALE configuration between these two systems , please guide me what bapi's , idocs and what background jobs i need to run on FI system or HR system
    please advise at the earliest.
    Regards,
    Najeeb ..

    http://searchsap.techtarget.com/general/0,295582,sid21_gci1130337,00.html
    http://help.sap.com/printdocu/core/Print46c/en/data/pdf/CABFAIS/CABFAIS.pdf

  • There is a voice over in my Ipad 2 and i cant unlock my ipad using my passcode

    Please Help! i just updated my Ipasd2 and there is this in accesibility, that made me in trouble. there is a voice over in my Ipad, whenever i touched it. and there i cant unlocked my Ipad. Help!

    Is this what you said? :
    You updated your iPad 2 to iOS 6. You were playing with accessibility (or turned it on accidentally) and turned voiceover on. Now you can't unlock your iPad.
    Do you know how to use the iPad in VoiceOver mode? First tap on what you would normally tap on. Then double tap anywhere on the screen. To unlock the iPad, tap on the "Slide to Unlock" bar. Double tap. Tap on the first character in your passcode. Double tap. Etc.
    To turn off voiceover (even without unlocking the iPad), triple tap the home button. tap on VoiceOver. Double tap.

  • Patch Issues on JMS bridges configuration between OSM and AIA

    Hi,
    As mentioned in the OSM AIA Order to activate cartridge guide, we want confirm whether the below private patch is mantatory to create the JMS bridge between OSM and AIA.
    Your Oracle Support ID is not sufficient to obtain the private patch. You will need the
    following credentials to access it.
    Patch identifier: 4CFJ
    What will be the outcome if we doesn't install the above mentioned patch.
    Regards,
    Murali

    Hi Murali,
    I would encourage you to use the Oracle Community (via the My Oracle Support) for questions related to patches. Please post your question in the community and I will be happy to assist you.
    - Deep
    (OSM Product Management)

  • Synching configuration between ECC and GTS

    Is there any way we can automatically synch configuration (e.g.countries, regions) from ECC to GTS?
    Thanks in advance.

    Transaction SCU0 lets you compare configuration between systems, based on a number of ways of selecting the items to compare.
    I am not sure if it offers any way to build a transport of the differences, or remotely update the target system.  At least it lets you know what is different.
    Andrew

  • SSL Connection Configuration between Apache and Weblogic 8,1

    I'm currently using Apache web server as a front end server for Weblogic server 8.1 and now i' facing some configuration problem to setting up the SSL connection between this 2 server. When i open my web application page, it shows
    Failure of Server Apache bridge
    No backend server available for connection: timed out after 10 seconds or idempotent set to OFF.
    and my proxy.log shows:
    Thu Nov 03 09:36:41 2011 <182413202842013> INFO: SSL is configured
    Thu Nov 03 09:36:41 2011 <182413202842013> INFO: SSL configured successfully
    Thu Nov 03 09:36:41 2011 <182413202842013> Using Uri /favicon.ico
    Thu Nov 03 09:36:41 2011 <182413202842013> After trimming path: '/favicon.ico'
    Thu Nov 03 09:36:41 2011 <182413202842013> The final request string is '/favicon.ico'
    Thu Nov 03 09:36:41 2011 <182413202842013> SEARCHING id=[ebwdsk298.ebworx.com:7002] from current ID=[ebwdsk298.ebworx.com:7002]
    Thu Nov 03 09:36:41 2011 <182413202842013> The two ids matched
    Thu Nov 03 09:36:41 2011 <182413202842013> @@@FOUND...id=[ebwdsk298.ebworx.com:7002], server_name=[10.122.50.218], server_port=[80]
    Thu Nov 03 09:36:41 2011 <182413202842013> attempt #0 out of a max of 5
    Thu Nov 03 09:36:41 2011 <182413202842013> general list: trying connect to '10.122.50.48'/7002/7002 at line 2696 for '/favicon.ico'
    Thu Nov 03 09:36:41 2011 <182413202842013> New SSL URL: match = 0 oid = 22
    Thu Nov 03 09:36:41 2011 <182413202842013> Connect returns -1, and error no set to 10035, msg 'Unknown error'
    Thu Nov 03 09:36:41 2011 <182413202842013> EINPROGRESS in connect() - selecting
    Thu Nov 03 09:36:41 2011 <182413202842013> Setting peerID for new SSL connection
    Thu Nov 03 09:36:41 2011 <182413202842013> 0a7a 3230 5a1b 0000 .z20Z...
    Thu Nov 03 09:36:41 2011 <182413202842013> Local Port of the socket is 2121
    Thu Nov 03 09:36:41 2011 <182413202842013> Remote Host 10.122.50.48 Remote Port 7002
    Thu Nov 03 09:36:41 2011 <182413202842013> general list: created a new connection to '10.122.50.48'/7002 for '/favicon.ico', Local port:2121
    Thu Nov 03 09:36:41 2011 <182413202842013> Hdrs from clnt:[Host]=[10.122.50.218]
    Thu Nov 03 09:36:41 2011 <182413202842013> Hdrs from clnt:[Connection]=[keep-alive]
    Thu Nov 03 09:36:41 2011 <182413202842013> Hdrs from clnt:[Accept]=[*/*]
    Thu Nov 03 09:36:41 2011 <182413202842013> Hdrs from clnt:[User-Agent]=[Mozilla/5.0 (Windows NT 5.1) AppleWebKit/535.1 (KHTML, like Gecko) Chrome/14.0.835.163 Safari/535.1]
    Thu Nov 03 09:36:41 2011 <182413202842013> Hdrs from clnt:[Accept-Encoding]=[gzip,deflate,sdch]
    Thu Nov 03 09:36:41 2011 <182413202842013> Hdrs from clnt:[Accept-Language]=[en-US,en;q=0.8]
    Thu Nov 03 09:36:41 2011 <182413202842013> Hdrs from clnt:[Accept-Charset]=[ISO-8859-1,utf-8;q=0.7,*;q=0.3]
    Thu Nov 03 09:36:41 2011 <182413202842013> URL::sendHeaders(): meth='GET' file='/favicon.ico' protocol='HTTP/1.1'
    Thu Nov 03 09:36:41 2011 <182413202842013> Hdrs to WLS:[Host]=[10.122.50.218]
    Thu Nov 03 09:36:41 2011 <182413202842013> Hdrs to WLS:[Accept]=[*/*]
    Thu Nov 03 09:36:41 2011 <182413202842013> Hdrs to WLS:[User-Agent]=[Mozilla/5.0 (Windows NT 5.1) AppleWebKit/535.1 (KHTML, like Gecko) Chrome/14.0.835.163 Safari/535.1]
    Thu Nov 03 09:36:41 2011 <182413202842013> Hdrs to WLS:[Accept-Encoding]=[gzip,deflate,sdch]
    Thu Nov 03 09:36:41 2011 <182413202842013> Hdrs to WLS:[Accept-Language]=[en-US,en;q=0.8]
    Thu Nov 03 09:36:41 2011 <182413202842013> Hdrs to WLS:[Accept-Charset]=[ISO-8859-1,utf-8;q=0.7,*;q=0.3]
    Thu Nov 03 09:36:41 2011 <182413202842013> Hdrs to WLS:[Connection]=[Keep-Alive]
    Thu Nov 03 09:36:41 2011 <182413202842013> Hdrs to WLS:[WL-Proxy-SSL]=[false]
    Thu Nov 03 09:36:41 2011 <182413202842013> Hdrs to WLS:[WL-Proxy-Client-IP]=[10.122.50.48]
    Thu Nov 03 09:36:41 2011 <182413202842013> Hdrs to WLS:[Proxy-Client-IP]=[10.122.50.48]
    Thu Nov 03 09:36:41 2011 <182413202842013> Hdrs to WLS:[X-Forwarded-For]=[10.122.50.48]
    Thu Nov 03 09:36:41 2011 <182413202842013> Hdrs to WLS:[X-WebLogic-Force-JVMID]=[unset]
    Thu Nov 03 09:36:41 2011 <182413202841921> INFO: No session match found
    Thu Nov 03 09:36:41 2011 <182413202842013> INFO: No CA was trusted, validation failed
    Thu Nov 03 09:36:41 2011 <182413202841921> INFO: DeleteSessionCallback
    Thu Nov 03 09:36:41 2011 <182413202842013> ERROR: SSLWrite failed
    Thu Nov 03 09:36:41 2011 <182413202842013> SEND failed (ret=-1) at 789 of file ../nsapi/URL.cpp
    Thu Nov 03 09:36:41 2011 <182413202842013> *******Exception type [WRITE_ERROR_TO_SERVER] raised at line 790 of ../nsapi/URL.cpp
    Thu Nov 03 09:36:41 2011 <182413202842013> Marking 10.122.50.48:7002 as bad
    Thu Nov 03 09:36:41 2011 <182413202842013> got exception in sendRequest phase: WRITE_ERROR_TO_SERVER [os error=0,  line 790 of ../nsapi/URL.cpp]: at line 3078
    Thu Nov 03 09:36:41 2011 <182413202842013> INFO: Closing SSL context
    Thu Nov 03 09:36:41 2011 <182413202842013> INFO: Error after SSLClose, socket may already have been closed by peer
    Thu Nov 03 09:36:41 2011 <182413202842013> Failing over after WRITE_ERROR_TO_SERVER exception in sendRequest()
    Can anyone tell me what should i do in order to correct this error? Your help is kindly appreciate!!! Please~

    1) Is the managed server up?
    2) from apache server are you able to bind the managed server port?
    3) can you pls send the weblogic ssl configuration?

  • Share files over the internet between PC and MAC server

    The set up:
    A MAC OS X 10.3.9 server running on a local network in the office sharing files with 15 windows XP and MAC.
    The problem:
    Can't connect a windows XP away (from home over the internet) to see files being share by the MAC server. I can do this with an other MAC from my home when I go to "Connect to server" and then I type the IP adress of my MAC server at the office, login with the user ID and then can see files on the server. When I am at the office, there is no problem with the windows XP machine to connect to the MAC server. When I am at home, I can connect with my windows XP machine to the MAC server at the office for FileMaker server (reside on MAC server at office), but I can not see the files shared on the MAC server over the internet when I connect via windows explorer serveradress
    (no firewall on the MAC server).
    Thank you

    I would like to know this, too. I'm trying to set up something with my bother on a PC. How does he make a connection on windows? I don't know what to tell him to do.
    Gabriel, do you have Wndows Sharing activated under Services in your Sharing Prefs?
    Tracy

  • Configuration between ipad and itunes

    Hello.
    I have an iPad 2 and I sincronice it with iTunes. All is fine. I make the changes in the order of the apps in the iPad and I want to transfer this order to the iTunes, but when connect it to the Pc and open iTunes, I select the device and before Apps. I can see the device but if I select Sincro Apps, the order in the device is changed by the order in iTunes.
    I dont know if I explain it well. I need to put my acctual order in the iPad to the iTunes. Thanks

    I think you are trying to keep the screens arranged the same way in iTunes as they are on the iPad? Is that what you want to do? The way the apps are listed under the Sync Apps heading means nothing if you want to arrange them on your own.
    Just tap and hold down on an app icon until all of the icons wiggle and then you can move the apps in an order that you want them on the iPad. You can also do the same thing in iTunes when your iPad is connected and iTunes is running. Try arranging the apps in iTunes and then sync and see if that makes a difference.
    There is no guarantee that when you sync the next time that the app arrangement will be maintained but all things being equal - it should work.
    Now - did I misunderstand you or am I on the right track?

  • Differences in MTU Configuration Between IOS and IOS-XR

    Hi all,
    If you're interested in this topic, you can now check document I posted in Service Provider section.
    Please let me know if you have any doubts.
    Thanks,
    Milivoje

    Thanks Andrew. The format is correct but only fills about half the screen. Big black borders on all 4 sides. On my ios 6 ipad it starts a video the same way but the i can do a reverse pinch and it will send the signal to the tv in full screen. Same format just bigger. It just doesn't work since i upgraded one ipad to ios7. Still works fine on the one i haven't upgraded.

Maybe you are looking for

  • Multiple text fields on the same line

    Hi Is it possible to have multiple text boxes on the same form line?  I'm trying to replicate a form I've created usng Acrobat X Pro but can't seem to figure how to do it with FormsCentral? Apologise if I'm missing something obvious!

  • Can we solve this problem -folder with the exclamation icon

    What is this folder with the exclamation icon? Why it happens only to the iPod connected to PC? Why it is the toughest problem to be solved? What causes it? Just would like to share my experience with all of you, my niece has a mini iPod that connect

  • No text displayed in PDF Document

    Hi @all, I want to download a PDF-Form to my local machine. Approach: - CALL FUNCTION 'FP_FUNCTION_MODULE_NAME' - CALL FUNCTION 'FP_JOB_OPEN' - CALL FUNCTION h_funcname - CALL FUNCTION 'FP_JOB_CLOSE' - CALL FUNCTION 'SCMS_XSTRING_TO_BINARY' - CALL ME

  • How do I compress the file

    My movie file is 4.8 gb and I need 4.2 to fit on my dvd. How do i make it smaller???

  • Troubles with Windows after installing Acrobat X

    I built a Windows 7 machine from scratch twice and ended up with the same issue.  As soon as I install Adobe Acrobat X Standard, Windows Explorer freezes whenever I right-click on something in Windows Explorer (icon on desktop or inside folder).  I d