Voice over IP: ISDN PRI Voice E1 - Calling Out problmes (PSTN)

Hi All,
Has anyone seen this before in a 'debug isdn q931' on a H323 gateway.
*Jun 15 07:39:03.893: ISDN Se0/2/1:15 **ERROR**: CCPMSG_OutCall: fails with cause 0x22.
When I am trying to call out side getting busy signal.The incoming calls working fine. But some times it working without any problems.
Please go through the attached configs...
Thanks
Ilyas

10.31.144.2#sh controllers e1
E1 0/2/0 is administratively down.
E1 0/2/1 is up.
Applique type is Channelized E1 - balanced
Cablelength is Unknown
No alarms detected.
alarm-trigger is not set
Version info Firmware: 20080918, FPGA: 13, spm_count = 0
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
Data in current interval (351 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 24 hours)
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
10.31.144.2#
10.31.144.2#sh network-clocks
Network Clock Configuration
Priority Clock Source Clock State Clock Type
1 E1 0/2/1 GOOD E1
10 Backplane GOOD PLL
Current Primary Clock Source
Priority Clock Source Clock State Clock Type
1 E1 0/2/1 GOOD E1
10.31.144.2#
*Jun 25 04:49:30.483: ISDN Se0/2/1:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Calling num 73845
*Jun 25 04:49:30.483: ISDN Se0/2/1:15 Q931: Sending SETUP callref = 0x02D4 callID = 0x8260 switch = primary-net5 interface = User
*Jun 25 04:49:30.483: ISDN Se0/2/1:15 Q931: TX -> SETUP pd = 8 callref = 0x02D4
Sending Complete
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9839F
Exclusive, Channel 31
Calling Party Number i = 0x0181, '73845'
Plan:ISDN, Type:Unknown
Called Party Number i = 0x80, '141'
Plan:Unknown, Type:Unknown
10.31.144.2#
In this output the E1 was up - able to call outside..., will try to get the down time output if necessary

Similar Messages

Can I add narrative, voice over or dub in voice to a slideshow created in Aperture 3?

Can I add narrative, voice over, or dub in voice to an Aperture 3 slideshow?

The only way to do that in Aperture would be to create the voice over in some audio program and import it into the audio browser and ten apply it to the sideshow. You can record directly in Aperture.
So you would first make the visual part of the sideshow, then play it back in Aperture and you record your voice over. Then import the voice over and add it to the sideshow.
Should work but you might find it easier to do it in somthing like iMovie or Final Cut. Export the sideshow from Aperture, import it into iMovie and do the recording there.

What is the use of enabling "speak notifications" on under the voice over in ios5 ? can it read out my notifications?? plz help...

i have recently updated my iphone 4 to ios 5. in the accessibility options i found the voice over and inside that i found the "speak notifications" . i enabled it on.. but doesnt know whats that for? can ny one help me? will it read out my notifications aloud? but its not working plz help..

create your own entreprise!indeed
I had a "dream" job for a while. a guy - who writes books on software process, and is a member of the agile alliance - had an idea for a product, sat on it for 15 years then left his job and started a company. he assembled his team personally, and 8 of us sat in a room and worked to make his idea a reality. he was the management, and he was also the most talented programmer of us all. the team ran beautifully, we rarely had a deadline to work to, save the odd launch here and there, and there was absolutely zero office politics. all we did was write code, toss ideas about, play with the development process and sometimes go karting, or to the pub, or for a curry or something. I actually looked forward to going to work every day, because of this free reign we had, and we all turned out orders of magnitude more code than anywhere else I've ever worked. but the investors got nervous and pulled funding, leaving the project somewhat crippled. nice while it lasted, though, and I learnt more in my short time there than I did at university, and across 5 years experience in other companies
so the answer is: come up with an idea, be expert enough to assemble and manage the perfect team and convince some rich people to lend you lots of money. simple. but be prepared. this guy was routinely doing 18 hour days, 6 days a week (he was a Christian, otherwise he'd undoubtedly be doing 8 days a week). he'd be out and about most of the day doing sales and marketing, flying around the world for meetings and stuff, then come into the office and code for 8-9 hours a night

Can't call out on PSTN after ethernet adapter failure in J4W

Hi all
Okay here goes.
We are currently deploying new laptops in our business. It's the brand new Lenovo X1 Carbon 2nd G. together with a USB based docking station. Unfortunately there is a very annoying bug with the docking station. The problem is that the dock ethernet NIC, suddenly disappears from time to time in Windows. This means that Jabber for Windows is failing over to the Wi-Fi network. This should be okay, but we are seeing an issue with J4W, when the ethernet NIC disappear.
The problem is that J4W can't call out to external phone numbers/PSTN, but all internal calls are working fine. Also it's possible to call from an external number/PSTN to the J4W client. But still, the J4W client can't call an external no. You will only hear a busy tone when trying to make an external call.
It doesn't help restarting the J4W client, we have to reboot the entire computer to make the client be able to call external numbers over Wi-Fi. Meaning that the ethernet NIC on the docking station, isn't reappearing after a reboot of the laptop. To make it reappear, we have to disconnect and connect the docking station cable.
Atm. we are waiting for a fix from Lenovo, but in the meantime I can't understand why we can't call external no. when the ethernet NIC fails. I mean, we can call external numbers. over Wi-Fi, but not when the ethernet NIC are failing.
Can anyone point me into the correct direction here?
Specs:
CUCM: 8.6.2.22900-9
CUP: 8.6.4.13900-4
J4W: 9.7
Gateway: Cisco 2911
OS: Windows 7 32 bit.

Hello Taxi-Anne,
Welcome to the forums.
Try following the steps below to turn off the call forwarding:
1. Touch Phone.
2. Swipe down from the top of the screen.
3. Touch the Settings icon.
4. Touch Call Forwarding.
5. Touch the required option (e.g., Forward If Busy).
6. Touch Save.
Let us know if this helps. Have a good day.
-SR
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

Video calls over E1 ISDN PRI link

Hi All
I have an ISDN E1 PRI Link through MGCP gateway, the telco say that they will provide a Video call service through this link for up to 30 calls!! is that possible (voice is working fine)??
What I know is a 64 k provided by each ISDN channel is not enough for Video calls unless using MCU or a gateway to aggregate the isdn channels.
Other people suggest that with H323 gw this can be done.
Call flow: Mobile Phone ==> ISDN ==> MGCP (or H323 if required) ==> CUCM==>Video enabled phone
Please advise..Many Thanks

Hi,
H.323 is supported in Cisco ISR routers. It is recommended to have dedicated video gateways the Cisco (ex Tandberg/Codian) 3200 Series would be better.
Section in the below: Dedicated Video Gateways
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/srnd/collab09/clb09/gateways.html#57896

How to prevent voice over saying the caller number or name automatically in iphone?

hi, i'm a new member of apple world,
i'm using voice over in my iphone 5s, when i receive a call, voice over automatically say the calling number or name with the ring tone, how can i set
voice over to prevent it saying the caller number or name ??

Same problem, which is extremely inconvenient because I like to use my earphones to listen to Pandora while I work. Not every time, but most of the time I plug in my earphones, the iPod software starts playing the last song that was played. Stopping the music via iPod or pressing the Home button for 10 seconds to force quit iPod doesn't stop the music as it will just automatically start playing again. Sometimes if I'm lucky, plugging the earphones in very quickly avoids this problem -- but like I said, it's a cross my fingers and hope I get lucky kind of thing.
I'm using the newer 3G model, which I've had for only about a month. I did not have this problem with my old 2G iPhone.
Someone in another thread said it's a hardware fault and suggested exchanging the phone for a new one. Can anyone confirm this?

How to prevent voice over saying the calling number ?

i'm using voice over in my iphone 5s, when i receive a call, voice over autamatically say the calling number or name with the ring tone, how can i set voice over to prevent it saying the caller number or name ?

It appears to be working as Apple intended. The manual says:
Moving recordings to your computer
You can sync voice memos with the iTunes library on your computer, and listen to them on your
computer or sync them with another iPod touch or iPhone.
When you delete a synced voice memo from iTunes, it stays on the device where it was recorded,
but it’s deleted from any other iPod touch or iPhone you synced. If you delete a synced voice
memo on iPod touch, it’s copied back to iPod touch the next time you sync with iTunes, but you
can’t sync that copy back to iTunes a second time.
Sync voice memos with iTunes. Connect iPod touch to your computer. Then in iTunes, select
iPod touch. Select Music at the top of the screen, select Sync Music, select “Include voice memos,”
then click Apply.
Voice memos synced from iPod touch to your computer appear in the Music list and in the Voice
Memos playlist in iTunes. Voice memos synced from your computer appear in the Voice Memos
app on iPod touch (but not in the Music app).
What yo can do is code the Voice Memos on the computer as something besides Voice Memos (Right click>Select Get Info>go to Option tap and change under Media Kind). When yo change it it will move the VM to the library for that kind e.g., Music if you coded it as Music)

Voice Over in iPod Nano too Bad

i have iPod nano Gen7, i just baught it when march 2013 Siver Color in my country (Thailand) My problem is Some time i was listen Radio or Music or do something with my iPod, Its always be Voice Over i dont know what they called it. just like siri Accesbility. She always tell me what i doing or what i listen. i so tired with Apple iPd. And i try to restore it but can't stop

Iphone 5s on iOS 8 stuck in accessibility voice over mode

Not actually a question, but more of a solution!!!
I went to my local Indian restaurant earlier and his phone was stuck in Accessibility mode. Having come home, and fiddling around with Settings > Accessibility > Voice Over, I accidentally turned voice over on, and the same problem persisted with me.
Firstly, a message came on my screen to ask whether or not I wanted to confirm, and if I wanted to cancel - press the home screen button. Having pressed the home screen button, the message stayed on the screen and the voice over kept repeating itself.
I then tried to restart my phone (Home and lock) but then I was just stuck within my lock screen and couldn't input my password.
To fix:
Double tap the home button to get onto your password lock screen.
Click the first digit of your password so the voice over repeats the number. Then double click the number again. - this should register.
Repeat the process until all digits have registered (it may take some perseverance). Your phone should unlock once all digits have registered.
Click settings (until it repeats the word) and then double click. You will notice, trying to scroll down that you are unable to. Turn your phone onto Aeroplane mode (you should have got the gist of how to select things and turn things on/off by now).
Once your phone is in aeroplane, click accessibility and then voice over, and once turned off your phone will work fine.

Recovery mode doesn't mean that all your data is already lost. You only lose your data if you restore it.
When you plug the phone is into iTunes hold down the home button. iTunes may then give you the option JUST to update the software first. This should not get rid of any data.
However, if iTunes is only giving you the option to RESTORE and update, then you will lose your data I'm afraid.
Hope that helps!

Voice over IP exam 9EO - 431

Hi,
I am trying to find a Cisco Press book that covers the topics required for this exam. Does anyone know what book I can buy?
Regards,
Gills

There is no Cisco press book yet designed just for this test. CVOICE class is the only good prep for it. If you want to get a good Cisco Press book that will cover a lof of what is in there get the following:
Deploying Cisco Voice over IP Solutions
and
Voice over IP Fundimentals
These would get you a good start,
Don

Different Voices for Voice Over For different countries.

Hi I was reading on Wikipedia the other day and found out that in Voice Over you can add voices for other countries instead of just having United States Voices. But where do i find them.
And if i got like a Latin America Spanish one if i typed something in Spanish would it speak it properly.

There are two main sources for voices in other languages that are compatible with VoiceOver:
Infovox iVox from AssistiveWare and
Cepstral voices.
Both allow you to listen to samples and to download and try the voices for yourself. Infovox iVox offer both Latin American and Castilian Spanish, while Cepstral offers only Latin American.
HTH
Archie

Ipad air - starts only "Voice over" after resume from stand by

Hi
today, in the morning, i used as always my ipad air (ios 7.01) for about 2 hours (i have it from about 1 month).
I saw only some email (no app installation, no IOS upgrade, nothing else)
Then i put it in stand by mode (by pushing on/off button).
When, in the afternoon, i resume it from stand by (pushing home button) , appears only the white page of "Voice over" and No other thing is possible to do.
I restarted it many times (on/off button + home button pressed for 10-15 seconds until apple icon appears) but after the startup only "Voice over" appears.
Only "Voice Over" is possible to use.................like the first time 1 month ago, when i started up it ad i have configured it for the first time.
It seems that the ipad was reset.
How is possible ?
It could be a IOS failure problem ?
or It's possible that someone has tried to unlock the ipad by pressing the wrong pin code and the ipad now is blocked (No one message that says "ipad blocked" or similar appears.........only "voice over" starts)????.
Please, someone can help me to understand what happened, in order to know what to do ?
How can i try to recover all the data in the ipad ?
Thanks a lot for all
Mario

I confirm that Only the white "setup" page starts (where is wrote "Hello > slide to set up").
The ipad seems that was resetted.
How is possible ?
It could be a IOS failure problem ?
or It's possible that someone has tried to unlock the ipad by pressing the wrong pin code and the ipad now is blocked (No one message that says "ipad blocked" or similar appears.........only "initial setup" starts)????.
I read in a manual of IOS 7 that is possible that the device is resetted after 10 times with wrong pin but after 5-6 times should appear a message with "ipad blocked for n° minutes" or a similar message.
No message appear....only the white page of the setup appears.
Please, someone can help me to understand what happened, in order to know what to do ?

Ipod shuffle voice over acting funny

Hi,
I bought the shuffle about 3 months ago. The past 2 weeks or so the voice over's been acting funny. Every time I click the voice over button the playback voice only says 'Playlist 1, Playlist 2' and so on for all my playlists. The song voiceover doesn't work either. There's just silence where its supposed to say the track and artist name. I tried resetting the settings back to factory default from itunes but no go. Whats wrong with it?
Thanks for helping me out.

Hi Imyman,
Apple has determined that the Apple Headphones with Remote included with the iPod shuffle (3rd gen) may fail under certain conditions. If your Shuffle has a certain serial number you can change your Headphones following this procedure:
http://www.apple.com/support/headphones/replacementprogram/
Hope this will solve your problem as it did for me.

Voice over Wireless

Hello,
I wanted to know whether Cisco Supports voice over wireless.
Thanks.

Voice-over-IP across an 802.11b network comes in three and a half forms: [comments welcome on other forms]
1. VoIP across a point-to-point (bridge-to-bridge) link
2. VoIP using a wireless client connecting through an H.323 gateway
3. VoIP using a wireless client without H.323
3.5 Voice over an AP to a proprietary gateway from Symbol or SpectraLink.
We are working on both #2 and #3 right now. Cisco likes a product from IPblue that runs on Windows or PocketPC and works with Cisco CallManager.
There are several reasons why we also like a non-H.323 solution from TeleSym - implementation may be less expensive (depending on your scenario) and it can off-load a lot of traffic from the PBX.
Symbol and SpectraLink are expensive but simple. Their phones are just phones, rather than having the additional PDA features we get in scenarios #2 and #3.
We can walk through this in more detail if you need.
Matthew Wheeler
Blue Modal

Voice over vpn-call not completing

Hi folks,
I got a problem,where with voice over vpn. So far my voip calls were running purely on shared IP internet. Today we had tried to make two side a vpn site-to-site tunnel and send traffic thru.vpn is working. (md5,des)
The problem We faced is when i dial a number, the other side party's phone rings for 6-8 seconds and the call gets disconnected.Whether or not the called party answers the call gets disconnected after 6-8 secs. Iam not getting any ring back, while actually other side phone rings. No voice is going thru.
my network is normalpbx--to--Cisco3800 to--Pix--to--QuintumGateway
isdn debug shows Cause code18-no user responding.
help me on this...

Hi,
can you provide configurations of the voice gateway and pix.
Anyway my best guess is the PIX:)
Check timers, check security policies.

Voice over IP: ISDN PRI Voice E1 - Calling Out problmes (PSTN)

Similar Messages

Maybe you are looking for