Voice-port

Estimados, tengo un duda. tengo un cisco 2800 que tiene un E1 interconectado a una Central y este a su ves se conecta aun proveedor SIP para realizar mis llamadas, esto funciona correctamente. Pero este mismo equipo tiene 4 port fxs lo cuales deben de conectarse a otro proveedor SIP para llamar, como puedo hacer para diferencia el plan de marcado de los puerto FXS del resto de lo otros.
Saludos.

Wrong forum, post in "voice - IP telephony". You can move you post using the actions panel on the right.

Similar Messages

Fax Blocked Voice Port (FXS)

hi,
an outgoing fax call blocked my voice port. it stays in a busy state for days... shut and no shut doesn't put the voice port in a dorm state again, only a reload will correct it... is there any solution instead reloading the c2800?
many thanks

Dino -
If you are running IOS 12.4, This seems to be attributed, possibly, to a known bug with the FXS port:
Cisco bug ID CSCse83674
http://www.cisco.com/cgi-bin/Support/Bugtool/onebug.pl?bugid=CSCse83674

No non-linear under voice-port to reslove hissing on NM-HDV

Hello.
I have a trouble with 2MFT on NM-HDV.
I can hear hissing on call.
So, i had configured no non-linear under voice-port, then i can't hear any hissing.
Instead, I can hear echo on call.
How can i fix it?
Regard,
john.

Hell Venky.
Thnak you for your helping.
I tried to configure based on the web site what did you told me.
But i couldn't success it to resolve echo issue.
The voice gate have 12.4(1a) on Cisco 2851.
So the solution to reslove echo doesn't fit in my case.
As i mentioned, normally i can hear noise each i talk another persion. If i stop the conversation i can't hear noise. but i started to talk again, i can hear noise each time.
Thus i tried to disable "no non-linear" parameter, i can hear echo instead noise.
So i should choice if i can hear noise or echo.
And also, i tried to change input gain and output attenuation from -6 to 14, but the each still can hear.
out voip network toplolog is below.
NEC Digital Phone---NEC PBX---Gateway---(cat6500---MSPP(WAN Area)---cat6500)---Gateway---NEC Digital Phone.
If i make a call using Normal Phone (INot Digital Phone), I can't hear noise. Whenever i can hear noise with NEC Digital Phone.
Here is the option on cisco 2851 with 12.4
2851(config-voiceport)#?
Voice-port configuration commands:
bearer-cap Specify the bear capability
busyout Configure busyout trigger event & procedure
comfort-noise Use fill-silence option
compand-type The companding type for this voice port
connection Specify Trunking Parameters
cptone Configure voice call progress tone locale
default Set a command to its defaults
description Description of what this port is connected to
disc_pi_off close voice path when disconnect with PI received
echo-cancel Echo-cancellation option
exit Exit from voice-port configuration mode
idle-detection Idle code detection for digital voice
input Configure input gain for voice
music-threshold Threshold for Music on Hold
no Negate a command or set its defaults
non-linear Use non-linear processing during echo cancellation
output Configure output attenuation for voice
playout-delay Configure voice playout delay buffer
shutdown Take voice-port offline
threshold Threshold [noise] for voice port
timeouts Configure voice timeout parameters
translate Translation rule
translation-profile Translation profile
trunk-group Configure interface to be in a trunk group
voice-class Set voiceport voice class control parameters
Please advise to me to reslove the problem.
Regard,
john.

Unable to configure voice ports on cisco2811

I have configured the Voice Gateway and calls are working internally.
I recently installed a WIC-1B-S/T-V3 card to prepare to getting outside line access.
To try a set of Dial-Peer and put the port command , but I have been rejected.
I've confirmed that　IOS Version,compatibility of WIC,PVDM is installed.
How do I get my WIC card to work?
The following is a show command.
【try set up】
R1#conf t
R1(config)#dial-peer voice 100 pots
R1(config-dial-peer)#port 0/0/0
^
% Invalid input detected at '^' marker.
R1(config-dial-peer)#port ?
<50-50> Voice interface slot #
R1(config-dial-peer)#port 50/?
<0-0> Voice interface SubUnit #
R1(config-dial-peer)#port 50/0/?
<1-20> Voice interface port # within vic
R1(config-dial-peer)#port 50/0/1
^
% Invalid input detected at '^' marker.
【show voice port summary】(i know 50/x/x voice port is automatically created.)
R1#show voice port summary
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
========= == ============ ===== ==== ======== ======== ==
50/0/1 1 efxs up up on-hook idle y
50/0/1 2 efxs up up on-hook idle y
-- omission --
50/0/20 1 efxs up up on-hook idle y
50/0/20 2 efxs up up on-hook idle y
【show ip interface brief】
R1#sh ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 192.168.11.110 YES NVRAM up up
FastEthernet0/1 192.168.110.1 YES NVRAM up up
BRI0/0/0 unassigned YES NVRAM up up
BRI0/0/0:1 unassigned YES unset down down
BRI0/0/0:2 unassigned YES unset down down
Loopback0 1.1.1.1 YES NVRAM up up
【show diag】
R1#sh diag
Slot 0:
C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time unknown
Onboard VPN : v2.2.0
-- omission --
PVDM Slot 0:
16-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
Hardware Revision : 4.0
Part Number : 73-8538-05
Board Revision : A0
Deviation Number : 0
Fab Version : 04
PCB Serial Number : FOC104518AZ
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 00
Product (FRU) Number : PVDM2-16
Version Identifier : V01
EEPROM format version 4
EEPROM contents (hex):
WIC Slot 0:
BRI S/T - 3086 WAN daughter card
Hardware Revision : 1.0
Top Assy. Part Number : 800-24973-01
Board Revision : B0
Deviation Number : 0
Fab Version : 01
PCB Serial Number : FOC10515ZRK
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : WIC-1B-S/T-V3
Version Identifier : V01
【show inventory】
R1#sh inve
NAME: "2811 chassis", DESCR: "2811 chassis"
PID: CISCO2811 , VID: V01 , SN: FHK0934F0HR
NAME: "Wan Interface Card BRI S/T (3086)", DESCR: "Wan Interface Card BRI S/T (3086)"
PID: WIC-1B-S/T-V3 , VID: V01 , SN: FOC10515ZRK
NAME: "PVDMII DSP SIMM with one DSP", DESCR: "PVDMII DSP SIMM with one DSP"
PID: PVDM2-16 , VID: V01 , SN: FOC104518AZ
【show version】
R1#sh version
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(7), RELEASE SOFTWARE (fc6)
ROM: System Bootstrap, Version 12.3(8r)T7, RELEASE SOFTWARE (fc1)
System returned to ROM by power-on
System image file is "flash:c2800nm-adventerprisek9-mz.124-7.bin"
Cisco 2811 (revision 53.51) with 247808K/14336K bytes of memory.
Processor board ID FHK0934F0HR
2 FastEthernet interfaces
1 ISDN Basic Rate interface
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
62720K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
【show run】
R1#sh run
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname R1
boot-start-marker
boot-end-marker
no aaa new-model
resource policy
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.110.1
ip dhcp pool VLAN10
network 192.168.110.0 255.255.255.0
default-router 192.168.110.1
option 150 ip 192.168.11.200
isdn switch-type ntt
voice-card 0
no dspfarm
interface Loopback0
ip address 1.1.1.1 255.255.255.255
interface FastEthernet0/0
ip address 192.168.11.110 255.255.255.0
duplex auto
speed auto
interface FastEthernet0/1
ip address 192.168.110.1 255.255.255.0
duplex auto
speed auto
interface BRI0/0/0
no ip address
encapsulation hdlc
isdn switch-type ntt
isdn point-to-point-setup
isdn incoming-voice voice
isdn map address .* plan unknown type unknown
router ospf 1
log-adjacency-changes
network 1.1.1.1 0.0.0.0 area 0
network 192.168.11.0 0.0.0.255 area 0
network 192.168.110.0 0.0.0.255 area 0
router ospf 12
log-adjacency-changes
ip http server
no ip http secure-server
control-plane
dial-peer voice 100 pots
destination-pattern 0T
incoming called-number .T
direct-inward-dial
call-manager-fallback
max-conferences 8 gain -6
ip source-address 192.168.11.110 port 2000
max-ephones 10
max-dn 20 dual-line
end

Hi,
the card which u are using supports Data .
you need to have VIC cards like VIC2-2BRI-NT/TE for Voice to work.
http://www.cisco.com/c/en/us/support/docs/voice/digital-ccs/7960-2isdn-bri-vic.html
regds,
aman

2800 config with 4FXO VIC, voice-ports?

I'm trying to configure the voice-ports on a 2800 router with a 4 port FXO VIC and when I issue the voice-port command it only shows ports 50-50 so I use
voice-port 50/0/1 and it comes back with invalid input at marker and it points to the 50.
boot-start-marker
boot system flash flash:c2800nm-ipvoice-mz.124-4.T.bin
boot system flash flash:c2800nm-spservicesk9-mz.123-8.T8.bin
boot-end-marker
Lights on the FXO card are lit up but I do not have any cables plugged into them, am I missing something?
Thanks

I'm guessing this is the info on the pvdm2?
WIC Slot 1:
2nd generation - FXO Voice daughter card (4 port)
Hardware Revision : 5.0
Top Assy. Part Number : 800-21589-01
Board Revision : E0
Deviation Number : 0-0
Fab Version : 04
PCB Serial Number : FOC092447VB
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00

IVR session vs Voice port

What is the main difference between IVR session and Voice port ?
If we need 4 port for Voicemail and Auto-Attendant, we had configured 4 port of IVR session and 4 port of Voice port .
Is that correct, or only Voice port enough ?

I found that shortly after my post, no change. I shut/no shut and I even reloaded the CME. Other ideas?
chrs-phx-cme#sh run int serial 0/3/0:23
Building configuration...
Current configuration : 138 bytes
interface Serial0/3/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn incoming-voice voice
no cdp enable
end
chrs-phx-cme#sh run | sec voice-port
voice-port 0/0/0
trunk-group 1
connection plar 774
description 602.246.7607
caller-id enable
voice-port 0/0/1
trunk-group 1
connection plar 774
description 602.246.0310
caller-id enable
voice-port 0/0/2
trunk-group 1
connection plar 774
description 602.246.0954
caller-id enable
voice-port 0/0/3
trunk-group 1
connection plar 774
description 602.277.4233
caller-id enable
voice-port 0/1/0
trunk-group 1
connection plar 774
shutdown
description 602.264.1518
caller-id enable
voice-port 0/1/1
trunk-group 1
connection plar 774
shutdown
description 602.264.1705
caller-id enable
voice-port 0/1/2
timeouts call-disconnect 3
shutdown
caller-id enable
voice-port 0/1/3
no battery-reversal
shutdown
voice-port 0/2/0
timeouts ringing infinity
description Bogen Paging Adapter
voice-port 0/2/1
voice-port 0/2/2
voice-port 0/2/3
chrs-phx-cme#

Unity 7.1 Ordering Additional Voice Ports - Thru CUWL

/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";
mso-fareast-font-family:"Times New Roman";}
My customer has CUWL licensing and has (16) Unity(7.1) Voice Ports licensed today. Customer wants to add more Voice Ports, is this done thru the PUT tool or do I need a special part number, checked the Ordering guide, and went thru the Dynamic configurator but did not see any ordering options.
I assume it is done thru the PUT tool.

My first guess, unless you just didn't mention the licensing portion of this downgrade, would be just that...Licensing:
License Files and MAC Addresses
Each license file (except for the demonstration license file) is registered to the MAC address of the network interface card (NIC) on the Cisco Unity Connection server. The license file for one server cannot be used on a second server (for example, because you want to replace the Connection server). You must obtain a replacement license file that is registered to the MAC address on the second server.
The license file can be registered to only one MAC address. If the Connection server has a dual NIC, you must either configure it for network fault tolerance, which assigns one MAC address to both NICs, or disable one of the NICs and use the MAC address for the other NIC.
When you order a license file for a dual NIC that has been configured for network fault tolerance, specify the virtual MAC address that applies to both NICs rather than the physical MAC address for either of the NICs. The license file is registered to the virtual MAC address, so the license will continue to be valid even if one of the NICs fails.
You'll need to contact [email protected] (or TAC, I suppose) and request a new license. You should be able to get a temporary license that will get the system up and running until the permanent license is issued.
Hailey
Please rate helpful posts!

Cisco 3640 cant configure voice-ports

I've an cisco 3640 with a VWIC-2MFT-E1 network module. Can anybody tell me why i cant configure any voice-port? without able to configure voice-port, i cant assign any port for my "dial-peer voice xx pots". Anybody has any solution?
what im trying to do is sending voice data traffic to 192.168.10.1
controller E1 1/0
framing NO-CRC4
clock source line primary
channel-group 0 timeslots 1-31
interface Serial1/0:0
bandwidth 2048
ip address 192.168.10.2 255.255.255.252
ip mtu 300
encapsulation ppp
no ip route-cache
no fair-queue
no cdp enable
dial-peer voice 777 pots
destination-pattern 77T
no digit-strip
direct-inward-dial
forward-digits all

I've only got this from my controller E1
Vertigo(config-controller)#?
Controller configuration commands:
channel-group     Specify the timeslots to channel-group mapping for an
                    interface
clock             Specify the clock source for a DS1 link
default           Set a command to its defaults
description       Controller specific description
detect            Enable detection of loopback request
exit              Exit from controller configuration mode
framing           Specify the type of Framing on a E1 link
guard-timer       Guard timer (0-20) for xcsp calls - timer duration and
                    accept/reject on expiry
help              Description of the interactive help system
line-termination Specify the line termination for E1
linecode          Specify the line encoding method for a E1 link
loopback          Put the entire E1 line into loopback
mode              Configure the controller mode
no                Negate a command or set its defaults
shutdown          Shut down a E1 link (send Blue Alarm)
tdm-group         Configure DS0 group for TDM
Do i need DSP for the voice-ports? Please guide me on what more module i need to get. Thanks!!
https://supportforums.cisco.com/message/3022639;jsessionid=AF45FBC0DDB8636D70F9B526A367016F.node0

Purpose of local-alerting under voice-port?

Hello;
During a recent migration I noticed a "local-alerting" command under a couple voice-port configurations:
voice-port 2/1:23
local-alerting
I did not enter the command in myself, and I checked with the other engineers and all are positive they did not enter the command.
These were found under T1 PRI circuit configs and only showed up under a few (2 or 3) from a set of about 12 total circuits on 2 seperate gateways.
I tried researching this command, and it is not under any command reference doc I looked through, google was of no help as well, it does not even come up as a listed command when entering "?" under voice-port......
Is any one familiar with this command?
What does it do?
Are there any reference documents or links?
Would it be possible for it to automatically appear after certain events? (no one recalls entering this in)
Any help would be greatly appreciated.
Thank you.

This command only makes sense when local bypass of DSP is used, In which case to use DSP to generate local bypass ringback. it's a hidden command, that's probably why you don't see it in the command reference or any document avaialble.
Br,
Nadeem
Please rate all useful post.

Sh voice port summary output meaning

Hello,
Can anyone explain to me the output meaning for each voice port result, such as admin up or down, or oper dorm or up or status and what does xcc-voice and efxs mean?
Thanks,
sh voice port summary
                                                                               IN       OUT
PORT            CH   SIG-TYPE   ADMIN OPER STATUS   STATUS   EC
=============== == ============ ===== ==== ======== ======== ==
0/0/0:23        01 xcc-voice             up    dorm      none     none            y

Channel 1 on the T1 is in admin state of up and not connected to a call or ringing. "Show isdn status" is best to check if the T1 is up, and this command is good to check what channels are currently in use on the T1.

AS5300 - Voice Port Configuration Problem

Hi guys,
I'm trying to configure a E1 PRI 8 Port Module on a AS5300 (IOS: 12.3(18)) but after I configured the controller, I can't find the voice ports. if I do a sh voice port summ there are no voice ports listed.
The controller is showing up in sh controllers e1 0.
Also under the dial-peer there is no port command..
Anybody has had this issue before?
Thanks.
Best regards

here are the outputs:
Router#sh vers
Cisco Internetwork Operating System Software
IOS (tm) 5300 Software (C5300-JS-M), Version 12.3(18), RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by cisco Systems, Inc.
Compiled Wed 15-Mar-06 16:39 by dchih
Image text-base: 0x60008AEC, data-base: 0x618EC000
ROM: System Bootstrap, Version 12.0(2)XD1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
BOOTLDR: 5300 Software (C5300-BOOT-M), Version 12.1(17), RELEASE SOFTWARE (fc1)
Router uptime is 3 hours, 53 minutes
System returned to ROM by reload at 16:26:08 gmt Sun Jan 2 2000
System image file is "flash:c5300-js-mz.123-18.bin"
cisco AS5300 (R4K) processor (revision A.32) with 131072K/16384K bytes of memory.
Processor board ID 14898234
R4700 CPU at 150MHz, Implementation 33, Rev 1.0, 512KB L2 Cache
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
Primary Rate ISDN software, Version 1.1.
Backplane revision 2
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x30,
Board Hardware Version 1.80, Item Number 800-2544-03,
Board Revision A0, Serial Number 14898234,
PLD/ISP Version 0.0, Manufacture Date 8-Jul-1999.
1 Ethernet/IEEE 802.3 interface(s)
1 FastEthernet/IEEE 802.3 interface(s)
35 Serial network interface(s)
240 terminal line(s)
8 Channelized E1/PRI port(s)
128K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
8192K bytes of processor board Boot flash (Read/Write)
Configuration register is 0x2102
Router#sh run
Building configuration...
Current configuration : 2057 bytes
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
enable password cisco
spe 1/0 2/9
firmware location system:/ucode/mica_port_firmware
resource-pool disable
clock timezone gmt 2
no aaa new-model
ip subnet-zero
ip cef
isdn switch-type primary-net5
isdn voice-call-failure 0
voice call send-alert
voice rtp send-recv
voice service pots
voice service voip
sip
voice class codec 1
voice class codec 100
controller E1 0
framing NO-CRC4
pri-group timeslots 1-31
controller E1 1
clock source line secondary 1
controller E1 2
clock source line secondary 2
controller E1 3
clock source line secondary 3
controller E1 4
clock source line secondary 4
controller E1 5
clock source line secondary 5
controller E1 6
clock source line secondary 6
controller E1 7
clock source line secondary 7
interface Ethernet0
no ip address
interface Serial0
no ip address
clock rate 2015232
no fair-queue
interface Serial1
no ip address
clock rate 2015232
no fair-queue
interface Serial2
no ip address
clock rate 2015232
no fair-queue
interface Serial3
no ip address
shutdown
clock rate 2015232
no fair-queue
interface Serial0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice modem
no cdp enable
interface FastEthernet0
ip address 1.1.1.1 255.255.255.252
duplex auto
speed auto
ip classless
ip route 0.0.0.0 0.0.0.0 1.1.1.2
no ip http server
dial-peer voice 100 voip
destination-pattern .T
session protocol sipv2
session target ipv4:192.168.1.1
session transport udp
dtmf-relay rtp-nte
dial-peer voice 10 pots
destination-pattern .T
direct-inward-dial
sip-ua
no remote-party-id
sip-server ipv4:192.168.1.1
line con 0
line 1 240
line aux 0
line vty 0 4
transport input lat pad mop telnet rlogin udptn
end
Router#
Router#sh diag
Motherboard Info:
Backplane revision 2
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x30,
Board Hardware Version 1.80, Item Number 800-2544-03,
Board Revision A0, Serial Number 14898234,
PLD/ISP Version 0.0, Manufacture Date 8-Jul-1999.
EEPROM format version 0
EEPROM contents (hex):
   0x00: 00 01 01 30 01 50 03 20 00 09 F0 03 41 00 31 34
   0x10: 38 39 38 32 33 34 00 00 00 00 00 00 00 00 13 63
   0x20: 07 08 00 00 FF FF FF FF FF FF FF FF FF FF FF FF
   0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FRU NUMBER : AS5300
Slot 0:
Hardware is Octal E1 PRI, 8 ports
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x49,
Board Hardware Version 1.0, Item Number 800-3883-01,
Board Revision A0, Serial Number 14896274,
PLD/ISP Version 0.1, Manufacture Date 29-Jun-1999.
EEPROM format version 0
EEPROM contents (hex):
   0x00: 00 01 01 49 01 00 03 20 00 0F 2B 01 41 00 31 34
   0x10: 38 39 36 32 37 34 00 00 00 00 00 00 00 00 13 63
   0x20: 06 1D 00 01 FF FF FF FF FF FF FF FF FF FF FF FF
   0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FRU NUMBER : AS53-8CE1+=
Slot 1:
Hardware is Duo Density Modems
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x4C,
Board Hardware Version 1.0, Item Number 800-3680-01,
Board Revision A0, Serial Number 14049055,
PLD/ISP Version 2.2, Manufacture Date 7-Jul-1999.
EEPROM format version 0
EEPROM contents (hex):
   0x00: 00 01 01 4C 01 00 03 20 00 0E 60 01 41 00 31 34
   0x10: 30 34 39 30 35 35 00 00 00 00 00 00 00 00 13 63
   0x20: 07 07 02 02 FF FF FF FF FF FF FF FF FF FF FF FF
   0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FRU NUMBER : AS53-120-CC2=
Slot 2:
Hardware is Duo Density Modems
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x4C,
Board Hardware Version 1.0, Item Number 800-3680-01,
Board Revision A0, Serial Number 14055218,
PLD/ISP Version 2.2, Manufacture Date 7-Jul-1999.
EEPROM format version 0
EEPROM contents (hex):
   0x00: 00 01 01 4C 01 00 03 20 00 0E 60 01 41 00 31 34
   0x10: 30 35 35 32 31 38 00 00 00 00 00 00 00 00 13 63
   0x20: 07 07 02 02 FF FF FF FF FF FF FF FF FF FF FF FF
   0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FRU NUMBER : AS53-120-CC2=
Router#

SRST advice.translation-profile on voice-port drops after router reboot.

I have MGCP gateways that configured as SRST gateways too.
I have translation from internal numbers and vice verse then I use in config.
Here is the final result:
<b>
voice-port 0/0/0:15
translation-profile incoming 1
translation-profile outgoing 2
</b>
this translations work when gateway come in SRST fallback mode.
But
<b>
translation-profile incoming 1
translation-profile outgoing 2
</b>
configs drop from voice-port 0/0/0:15 when I have router reboot

You probably are using the 'ccm-manager config-server' command to download the MGCP config on registration. This is fine for basic operation, but part of the operation is that it will delete any existing voice configs. Therefore the voice port will be deleleted and this takes the translation profile along with it.
If your configuration is static and there are no changes being made on he CUCM gateway config, the easiest solution is to remove the 'ccm-manager config-server' command. Once you do this the other commands on the voice port will survive the reload since the router will no longer delete and then re-add the voice port.
If you do need the config download, you can use Embedded Event Manager (EEM) to re-add the translation profiles on the voice port after a reload. We would need a copy of your configuration to confirm the interface details to re-apply the configs against. If you want to try this option, paste your config into this posting.

How many digital voice ports can Cisco 3663 support ?

How many digital voice ports can Cisco 3662 support ?
They said "Medium complexity Codecs: 360 (E1)/288 (T1) and High-complexity Codecs: 180 (E1)/144 (T1) "in Cisco 3660 voice gateway data sheet .
But another document said you just configured 4E1 on a Cisco 3660 router .
Which one is true ?

Hi,
There are some other issue except physically accepted number of voice port.
http://www.cisco.com/en/US/products/hw/routers/ps259/products_data_sheet09186a00800921ed.html
page will give you better idea. Even though you can install many voice ports into a router , there is other limits you encounter.
Bets Regards

Voice Port stay Up when transfer to PSTN

Hello guys, i have a problem,
When i try to forward my Phone to PSTN my voice port stay UP and never hang up.
0/0 -- fxo-ls up up idle off-hook y
0/1 -- fxo-ls up up idle off-hook y
What can i do to resolve this issue.
Regards.

If you receive a call from the PSTN to your phone and have your phone forwarded to a PSTN number, it is normal behavior for these 2 ports to stay active for the duration of the call. If the ports are not disconnecting after the call is terminated, take a look at the following link for cause of this problem and possible solutions.
http://www.cisco.com/en/US/tech/tk652/tk653/technologies_tech_note09186a00800ae2d1.shtml
Hope this helps. If so, please rate the post.
Brandon

No cisco phone with voice port?

Hi
could any one advice me about "switchport voice vlan"?
I have a configuration like:
interface GigabitEthernet 1/-/1
description test phone
switch port access vlan 100
switchport mode access
switchport voice vlan 200
when I plug a no-cisco phone into this port, the phone try to get dhcp from vlan100, not vlan 200.
do I have any chance to force it go to vlan 200? o
Any comments will be appreciate
Thanks in advance
julxu

Hi
Most IP phones have some mechanism for setting the VLAN - Cisco phones use CDP, but other phones do not. Check with the manufacturer, or post up the type of phone you have.
For example, some phones require you to set custom DHCP options to set the VLAN.
Aaron HarrisonPrincipal Engineer at Logicalis UK
Please rate helpful posts...

Voice-port

Similar Messages

Maybe you are looking for