Voice recording with Macbook Pro

Hello, I am not sure if this is the correct forum to post this question but here goes:
Is there anyway to use the macbook pro to record a lecture? I saw in downloads there was something called" quick voice recorder "
Has anyone used this? How does it work? I see it says a microphone is required.
I have one meeting that I need to record and I can't afford to purchase a digital voice recorder device for a one time use.
HelP? suggestions?? thanks a lot

Your MBP has a built-in microphone.
I believe QuickVoice is a demo license (meaning without paying the license fee, it may be lacking some functions, record only for a limited time, etc.) - try it and see.
There's freeware that works quite well: http://audacity.sourceforge.net/

Similar Messages

How to use sony ic recorder with macbook pro, how to use sony ic recorder with macbook pro

Anyone can help? I realise there seams to be no software to syncronise my IC rec with my Mac.. I had one for my PC.. but not for Mac??

instructions from Apple: http://support.apple.com/kb/HT3131

I have a digital voice recorder with a 3.5mm mic and headphone jack and want to transfer some recorded lecture to my mac book pro. The mac book does not have 3.5mm jacks. Does anyone know if a jack to USB converter would work?

I have a digital voice recorder with a 3.5mm microphone and headphone jack and want to transfer some recorded lectures to my mac book pro. The mac book does not have 3.5mm jacks. Does anyone know if a jack to USB converter would work?

Is there a pattern to the time of day or other detail that may be
traced back to a OS X system cause of this odd phenomenon?
Are there any copies of system files on any of the attached USB
external drives? Any libraries, such as iTunes, iPhoto, etc?
Once the drives are indexed by Spotlight, are their permissions
ignored by the OS X? Content, if neutral, should not affect the
wake or sleep cycle; especially if they're ignored by the OS X.
Could there be a bad cable or other component? If so that would
be a difficult process of elimination to detect it. Usually replacing
most suspect components in the USB stream (external to Macs)
is a rote way to mechanically test that idea; & not 100% sure.
Does the equipment all have a good ground to the utility or house
electrical field? An intermittent ground may affect more than sleep.
Hard to say at this point. Maybe a late-night talk radio guru on
remote viewing could peer into your situation and sleuth it out?
Sorry to have run out of ideas, but the process must be electrical
& mechanical to some extent. - Or perhaps odd software inspired.
Do you have any phone-home spyware items inside, just jumping
at the chance to spill your information? Little Snitch may help.
PS: Perhaps the computer needs to go into Apple & have a genius
or product specialist at AASP test the unit thoroughly... BlueTooth?
see:
https://www.google.com/?gws_rd=ssl#q=Wake+reason:+XHC1
Good luck & happy computing!
edited 2x

Voice Over with Soundtrack Pro

I have spent about 8 hours on this and can't figure out how to voice over with Soundtrack Pro. I could do it with Soundtrack but something is different with this new version. I have not used StP that much, so I am relying on you pros out there to get me started in the right direction! Thanks everyone for your help.
I did search for related topics but found nothing that was along the lines of what I needed.

Well, I finally found that if I switch to standard layout then the "transport controls" appear. For some reason they are not in the other layout that has separate mixer and video windows. Now I am recording and everything is fine.

Audio recording with QT Pro vs. QT Broadcaster

Need to record a seminar (audio only) and live webcast parts of it. Audio goes from mixer to line in on Macbook with QT Pro and QT Broadcaster. Broadcaster will record to disk, but it appears to have no metering. It also appears that to record with Broadcaster, you have to be broadcasting. I successfully recorded with QT Pro while broadcasting. Questions:
1) With QT Pro, how far into the red is safe on recording?
2) Are there any input metering options (like displaying the peaks for a second or two)?
3) Can you change the default naming from Audio n.mov to something else?
4) With QT Broadcaster, is there any level indication - how can you tell if your level is good?
5) It seems simplest to record with QT Pro and just turn on Broadcaster when needed. QT Pro won't let you pause a recording and resume with the same file, but I can live with that. But is there a better way to do this?
Thanks,
John

OK, that is really true...
While I was waiting for a reply, I tried what David suggested and used my video Hi8 to simulate a transfer with no sound except the one from my tapes....and guess what ????
it works !
I am going to try it again with STP and QT7 under same conditions.
Funny that these boxes seem to need a video running.
Even more than that, I have tried an empty tape...and it does not seem to work !
Which means you really need an active signal
thanks a lot for this reply which is very helpful
Ivan

Recording into MacBook Pro.

Recording into MacBook Pro. I currently record vinyl records from phonograph into 2008 MacBook Pro Yosemite OS using the audio input jack on the MacBook. The new MacBook Pro doesn’t have an audio input jack. How can I record from the phonograph into the MacBook? Can I use something like the Behringer Audio Interface into a USB port?

You will have to look for hardware and software to connect to a USB port. (I am not familiar with Behringer)
Ciao.

Cinema Display (clear) with DVI/ADC box doesn't work with MacBook Pro

Cinema Display (clear) with DVI/ADC box doesn't work with MacBook Pro when plugged in with a dvi to mini dvi cable. Any ideas what to do to make it work? I lugged the 23" 2500 miles into the wilderness and I need help

Okay, here's an update: the DVI to ADC adapter does work with the Apple displays that I have tried, but it won't work with the Formac. I have tried multiple time to contact them, but to no avail... they don't even respond to threats of posting my opinion of them, which is this:
DON'T BUY ANYTHING FROM FORMAC! They make quality products, but their customer service is a big time joke! They won't take care of you.

How can I restore data from my iPhone after sync with macbook pro?

I accidentally syncronized my Iphone with MacBook Pro on iTunes and lost all data from my phone (calendar, contacts, photos, etc.). Is there a way to recover that information? Thank you!

Welcome to Apple Support Communities
You cannot. However, you can solve this problem by setting the iPhone as a new device and upgrading iOS in Settings -> Software Update.
After upgrading iOS, open Settings -> General -> Reset -> Erase All Content and Settings. Finally, Setup Assistant will let you restore the backup.

External hard drive compatible with macbook pro 10.5.8

external hard drive compatible with macbook pro 10.5.8, i need a hard drive that will work with 10.5.8 to back everything up before upgrading to 10.6. a hard drive that is compatable with 10.5.8 has been impossible to find, a hard drive that works with both opperating systems is what i am looking for, any information that can help is appreciated

You can buy just about any USB2.0 hard drive and use it with your MacBook Pro. Many older external drives come pre-partitioned and formatted FAT32 for use on Windows. Your Mac can use that file system as well, but it has limitations on file sizes. You can always re-partition your external drive and re-format it as HFS+ (MacOS Extended Journaled) then your old Mac OS version and your new one should both be able to access it just fine. One thing to keep in mind is that many older OSes don't really handle drives larger than 2TB well, so you would probably want to try to keep your external drive to something smaller than 2TB...

I am recording with Logic Pro X, using my Yamaha XS8 keyboard as a Midi controller. I also have a Thunderbolt Display. Every time I play and release a note on the keyboard, the Thunderbolt Display speaker emits a doink sound. How do I get it to stop?

I am recording with Logic Pro X, using my Yamaha XS8 keyboard as a Midi controller. I also have a Thunderbolt Display. Every time I play and release a note on the keyboard, the Thunderbolt Display speaker emits a doink sound. What is causing it and how do I get it to stop? My sound is running through the Saffire Pro 40 Interface (Focusrite) into external speakers with powered amps.
Also, When I record I am hearing little pops in the system. I have checked all of my meters and they are not clipping. What is causing it and how do I get it to stop?
Ken

MUYconfundido wrote:
Pancenter,
Thanks for the response, but I do not have a midi interface. I am using a midi to usb connector cable, thus bypassing the need for a Midi interface.
The Mac reads the USB cable as a midi device, but not the keyboard that I am trying to use as a controller. I have tried it with my korg sp 300 and with my Nord Electro 2.
Thoughts?
Thanks,
Tristan
Tristan...
This is what you have, correct?
http://www.alesis.com/usbmidicable
This from Alesis..
"The AudioLink Series USB cable receives and outputs MIDI signal thanks to its internal interface. The USB-MIDI Cable connects plug-and-play to your Mac or PC for an all-in-one USB-MIDI solution."
Notice, -internal interface-. What you have is a simple USB MIDI Interface. Most MIDI interfaces are USB.
My point is (was), MIDI OUT of the Korg goes to the connector marked MIDI IN on the Alesis, those new to MIDI often get this wrong.
pancenter-

Does Adobe Photoshop Elements work with MacBook Pro with Retina display?

Does Adobe Photoshop Elements work with MacBook Pro with Retina display, please?
Have searched Adobe website for answer - most recent is 2013 answer, saying no.
Contradicted by a staff ember who only referred to Photoshop, not Elements.
Reason I need it is that iPhoto does not support very high resolution photos - which I have now scanned onto my MacBook and do not want to re-scan!! After 90 minutes at my local Genius bar (lovely folk, very conscientiously searching for an answer...), re-scanning was their final piece of advice.
Help, please...

Hello Smis,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I understand you are having issues with your HP Monitor on your MAC. I am providing you with an HP Support document: Updating a Monitor Driver, where it states under the sub-heading Using HP monitors on a Mac "HP monitors are not supported in a Mac environment. However, newer Macs use graphics with VESA modes and can display to most HP LCD monitors. To do this, connect the monitor to the Mac while the Mac is off, and then turn on the MAC. The monitor should operate at 60Hz. The INF and software for the HP monitor are for Microsoft Windows and cannot be run in a standard MAC OS environment."
This being said all I can advise is that you check to see that the monitor is set to operat at 60Hz and contact Apple for assistance if that does not get your monitor displaying correctly.
I hope I have answered your question to your satisfaction. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

Time Capsule works with MacBook Pro (Mavericks) but not with IOS devices? recent problem starting March 1, 2015.

I have a Time Capsule version 7.7.3 (model A1470) which has worked fine for almost 2 years with all devices, Apple and otherwise. As of beginning of this month, March 2015 - no longer works with a new IPAD mini 3 and 6-month old iPhone 6 (both updated as of last night) BUT still works fine with MacBook Pro (Mavericks 10.9.5) and Epson printer XP-600.
On both IOS devices Airport Utility shows the Time Capsule and shows green light connection to internet, but never does the connection. The little status circle just keeps going round and never shows the Wifi rainbow symbol. both devices work fine on other Wifi's. Airport Utility on iPhone actually connects enough to check on Airport base station's firmware 7.7.3 and says it is up to date! but sadly stays on LTE.
Have tried resetting, replugging etc...
Also, tried checking on updates. Nothing shows in Airport Utility. When I try to go to see past updates ~/Library/Application Support/Apple/AirPort/Firmware to see if updated, there is no Airport in the Apple folder?
A mystery...

Reset the TC to factory and redo the setup. see details below.
Here is the typical list of things you should try.. and if this doesn't help post again.
Factory reset universal
Power off the TC.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the TC to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
N.B. None of your files on the hard disk of the TC are deleted.. this simply clears out the router settings of the TC.
Setup the TC again.
ie Start from a factory reset. No files are lost on the hard disk doing this.
Then redo the setup from the computer or perhaps it is better using iOS on the phone or ipad currently having issues.
1. Use very short names.. NOT APPLE RECOMMENDED names. No spaces and pure alphanumerics.
eg TCgen5 and TCwifi for basestation and wireless respectively.
Even better if the issue is more wireless use TC24ghz and TC5ghz with fixed channels as this also seems to help stop the nonsense. But this can be tried in the second round. For iOS the fixed channels particularly for 2.4ghz has helped.
2. Use all passwords that also comply but can be a bit longer. ie 8-20 characters mixed case and numbers.. no non-alphanumerics.
3. Ensure the TC always takes the same IP address.. you will need to do this on the main router using dhcp reservation.. or a bit more complex setup using static IP in the TC. But this is important.. having IP drift all over the place makes for poor networking. If the TC is main router it will not be an issue. This is a problem for a TC in bridge mode.
If this is of no help.. what modem do you have? What function other than modem does it have.. ie none or router??
How is the TC connected into the network? What function does it have? Router or bridge for example.
Post a few screenshots of the setup.

I have just used air display with macbook pro. i have disconnected now from apple tv. but my laptop screen is still very small like its connected to the tv. this means all the tabs and writing is very small, how do i full disconnect my laptop?

i have just used air display with macbook pro. i have disconnected now from apple tv. but my laptop screen is still very small like its connected to the tv. this means all the tabs and writing is very small. like the display down the bottom where al the applications are, is n the middle of the page and not spread down the bottom. this is seriously annoying! all the writing is every small and the tabs are small and its hard to read. the air display link has disappeared from my computer. but the laptop screen is still very small. i want to know how do i get rid of this and return my macbook screen to its normal size. thank you

Hello chrispyw,
If your content is still being displayed incorrectly, I would check the resolution setting for the built in display with this article:
OS X Yosemite: Adjust your display’s resolution
If it keeps happening whenever you use AirPlay then I would use this section of the following article to reset the display system:
Apple computers: Troubleshooting issues with video on internal or external displays
Reset the system
You can reset the Mac's parameter RAM and SMC.Reset the resolution
Start by resetting the Mac's parameter RAM. If the display does not come up, was previously set to an unsupported resolution, and still results in no video:
Start up in Safe Mode.
From the Apple () menu, choose System Preferences.
Choose Displays from the View menu to open the preferences pane.
Select any resolution and refresh rate that your display supports.
Restart your computer.
Thank you for using Apple Support Communities.
Regards,
Sterling

What is the best external hard drive with MacBook Pro

What is the best external hard drive with MacBook Pro?

I agree with Allan, and that link is also called OWC, their hard drives are great. Have three of their Mercury Pro Elite 2 TB quad interface drives. They will connect eSATA, Firewire 800 & 400, USB2, so broad reange of options. Drives seem to come Mac HFS formatted, but I always reformat and partition the drives. Service and quarantees are top notch.
They offer a wide range of drives/drive systems so like Allan said, spend some time seeing what the have.

Is it easily possible to synchronize mails sent from iphone 3GS with MacBook Pro retina

is it easily possible to synchronize mails sent from iphone 3GS with MacBook Pro retina

Read through this:
http://clients.websavers.ca/whmcs/knowledgebase/115/Keeping-your-Sent-folder-in- sync-across-devices.html

Voice recording with Macbook Pro

Similar Messages

Maybe you are looking for