Voicemail disappears from system after sending to Exchange

Have Cisco 7960 IP Phones. Exchange 2003. When a voice mail comes in the message waiting light comes on on the phone and the message is forwarded to Exchange/Outlook. Before the user reads/.opens the mail the message light goes out and message can no longer be retrieved through voicemail.

One scenario where this would happen is if your users are using POP for mail retrieval and the email client pulls mail from the server without leaving a copy. A couple of solutions:
1. Use IMAP instead of POP mail
2. Set the email client to leave a copy of the message on the server. In this case, the MWI will still go off, but messages will be available throught the TUI as a saved message.
Hope this helps. If so, please rate the post.
Brandon

Similar Messages

  • Windows 7 disappear from bootcamp after  maverick installation

    Windows 7 disappear from bootcamp after  maverick installation. What should I do to recover?
    I did try co reinstall windows but it make the installation new (nothing remain from the previous). Old windows partition seems lost.

    Hi Jack.........ok ive managed to create a link to that video on how to install bootcamp.....this is the tutorial i used and i managed to gain 100% completion on bootcamp 1st time no messing......like i said in my previous reply did you save the windows support files from apple....(Critical).....ok no point in messing about i suggest you start again from scratch........these are the things i used and YOU will need to complete bootcamp
    mem stick or cd-r / dvd-r......original copy disc of win 7 ...i never used an iso i used original disc....allow a minimum of 30gb of space for your win 7 partition.....if you want bootcamp so you can use big programs like windows based games i.e.....Crysis/Call of duty etc etc ..then you will need to consider that  you will need to allow a bigger partition to allow your HD to store the files.....this is the reason i installed bootcamp and so i made my partition    i have a 750GB HD so i made a partition of 300gb for windows 7 and left the other 450gb for Mac....so you need to partition enough for what you want bootcamp for remember once you get bootcamp working you will need to install ALL Important Windows updates Including Win 7 SP1......once everything is installed you will have bootcamp up and running lovely.....u can then boot up with either win7 or mac......click this link and watch carefully and do exactly as shown ok and you should be fine...if you have any probs contact me again ok.....let me know how you get on ok..:)...http://www.youtube.com/watch?feature=fvwp&v=QFIWtXTl4d0&NR=1

  • Nm-applet,power-manager ....disappeared from panel after "pacman -Syu

    i use gnome-shell ............nm-applet,power-manager ....disappeared from panel after "pacman -Syu............in pacman -Syu.... dbus was updated..............now when i type nm-applet in the panel i get :
    nm-applet
    ** Message: applet now removed from the notification area
    earlier before upgrade it was working perfectly ......please help

    i use gnome-shell ............nm-applet,power-manager ....disappeared from panel after "pacman -Syu............in pacman -Syu.... dbus was updated..............now when i type nm-applet in the panel i get :
    nm-applet
    ** Message: applet now removed from the notification area
    earlier before upgrade it was working perfectly ......please help

  • TS3899 Saved messages disappear from mailboxes after 'update'.

    Saved messages often disappear from mailboxes after an automatic 'update'. Why does that occur? If it's normal, how long are messages retained in a mailbox? Thanks

    Hi Milli,
    I think the problem is that Mail tries to download them in order & if it runs into one it can't it just stops, happens when a bad/malformed email is in the chain too.
    I think this may have cleared your problem though...
    Not certain, but this can fix myriad Mail problems...
    Safe Boot from the HD, (holding Shift key down at bootup), it will try to repair your Disk Directory while the spinning radian is happening, so let it go, run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, then move these folder & file to the Desktop.
    Move this Folder to the Desktop...
    /Users/YourUserName/Library/Caches/Mail/
    Move this file to the Desktop...
    /Users/YourUserName/Library/Mail/Envelope Index
    Reboot.

  • Exchange Calendar Events Disappearing from iPhone after Editing

    iPhone 6 running iOS8.
    Exchange calendar events are disappearing from iPhone right after I edit them from my phone. But they are still visible on my MacBook in Outlook.
    It used to happen very rarely but lately it has been happening very frequently. Haven't been able to find a pattern and re-create it.
    Tried searching online for this issue. Found quite a few threads about calendar sync issues, including the GMT bug but haven't been able to find this exact issue that I have been facing.
    Any suggestions will be highly appreciated.

    I have the same problem and it has nothing to do with filing or moving emails,  for instance just before I logged in here to find a solution for the problem, I had just received and email on my iPad.  I was reading it then clicked on a link.  When I finished reading the link In Safari  and went back to the email, it was gone.   I have replied to an email then come back to it and it was gone.  This had nothing to do with viewing the email on a ore device.  This is a real problem I have asked about before and no one seems to know the answer.

  • Diagnostics: Agent disappearing from system landscape

    Hello,
    I want to monitor my Enterprise Portal (EP7) and use Root Cause Analysis for it.
    I installed the SMD Agent on EP7, diagnostics is running on SolMan (SM7).
    Now the strange part:
    Whenever I start the Agent on EP7, I can see it for a short time in diagnostics (e.g. in the landscape management or in the managed system setup wizard).
    But shortly after (between 30 - 60 sec.), the agent disappears from diagnostics. Although it is running all the time, it does not show up anymore.
    Diagnostics says, the agent is not connected resp. does not found an agent. But it's up and running (and was visible just seconds before) on EP7.
    Anybody any idea, why this behaviour occurs?
    Thanks and Regards,
    Jan

    Hi,
    We have used same SIDs (the default DAA) for a few hosts in our landscape and this did not cause a problem.
    But in my opinion best to use DAA, DAB, DAC etc in order to remove any room for confusion for both the humans and the systems
    Regards,
    Srikishan

  • Disks disappeared from Desktop after 10.5.4 - 10.5.8v1.1 update

    Hi,
    a strange think happend today after a server update from 10.5.4 to 10.5.8v1.1 with a downloaded combo installer: After the reboot 3 of 5 1 TB firewire disks disappeared from the desktop! Just gone. What makes the whole thing really tricky: they show up in the disk utilities as mounted! Repairing them doesn´t change a thing. Disk Warrior doesn´t help. What´s even more mysterious: Opening the terminal, cd to the /Volumes folder ls shows folders for all five disks. But "ls -l" produces an "Access denied" error for each of the missing disks! It requires a sudo to show the permissions of the disks! What´s more disturbing: The permissions of the disks not showing up are ending with an "+" while all the other disks have an "@". But what really knocks me of that you can mount and work with the missing disks over the network! I really need help with that.
    Greetings,
    Mike

    Hello mibobby,
    I'm seeing something similar to the problem you reported here. I my case there are 4 external hard drives connected to the Xserve 10.5.8. All drives are visible from Disk Utility, The Finder, and terminal. However, if a drive is plugged into another system, 10.5.8, or 10.6.2, the drives will not mount in the Finder. They appear in Disk Utility, but the volume appears as a blank piece of paper rather than a hard drive icon. If you navigate to the volume vial the terminal, you get an error indicating that you do not have permissions. Any thoughts would be appreciated.
    Did you ever get your problem resolved?
    Thanks
    Dean

  • Username 'disappeared' from System Preferences List

    System is a MAC Mini with 8GB of memory and 250GB SSD with a 4TB Pegasus R4 subsystem.  It is running Mavericks 10.9.4 and Server 3.1.2.  A month or so ago one of its non-admin users disappeared from the System Preferences User list and from the server app's Users list. The user is unable to connect  to the server. When I tried to recreate the user I was told that the shortname is already in use. Changing the name of the folder in /Users doesn't change anything.
    I need to either regain access to the username or delete the username so I can create it again.
    Can anyone help me?

    The following command will output a list of local users. Is the one in question included?
    dscl . -list /Users

  • Podcasts disappear from aTV after listening

    Bit frustrated! Can any one tell me if I can stop podcasts disappearing from the listing on my Apple TV after I have listened to them? I want to listen to some more than once.
    There must be a way; I find it difficult to believe someone has decided we will want to listen to any given podcast only once.
    This is a problem since iTunes 10, but I stress this may be because have just noticed it happening - I'm not saying it's definitely an iTunes 10 issue. I have podcast syncing switched off (so they all stream from my Mac), but I have tried syncing and the same thing happens.
    Thanks,
    S.

    Yes; YOU may have tried it and the problem didn't appear for YOU. Thank you. I note you're not using a Dual PPC Mac, or OS 10.5.
    I was requesting help from others who may have the time and inclination, so I could tell whether or not YOUR setup is unusual in some way. I'm not satisfied with anecdotal reports from only two people (you and me). Please don't put other people off helping me.
    I feel its too early to say how likely it is that the problem is specific to my media files: If my media files (downloaded just like everyone else's are), iTunes, the Mac or the aTV have suddenly started behaving oddly, on their own, then I feel it's slightly more likely to be a bug somewhere than anything else. I'm trying to find out for sure, though.
    And remember, some one else is having a not too dissimilar problem.
    Do you know how I can report a bug?
    Thanks again,
    S.

  • GPO Disappeared from "Controlled" after checking in

    I've been using AGPM for some time but haven't seen this before. I made a single change to my IE policy and checked it back in. At that point it threw an error (which I didn't screenshot thinking it would be in the event viewer). After the error, the
    policy disappeared from AGPM entirely. I thought it might be under pending or recycle bin but it is literally under no tab.
    However, the policy DOES still exist in the regular domain locations under Group Policy Management outside of AGPM. The guid folder is also still present in the domain policy folders. The policy minus my new change appears to be applying properly.
    At this point I'm not sure how to get it back in AGPM to where I can edit and deploy it. I've tried rebooting the server and logging in with different accounts on the AGPM client but haven't been successful. From the GPM interface, I was able to fall back
    to a previous version under the history tab but that didn't put the file back either.
    Any ideas?

    Called Microsoft support and they couldn't figure out what happened. Their recommendation was to delete the policy and recreate it from scratch. While this got me back up and running, it was not an easy process as this policy was quite large. 
    They couldn't tell me how to prevent the problem in the future given that they couldn't figure out why it happened, so I'm concerned about this going forward. 

  • JMS destinations disappear from JNDI after appserv restart

    I am using the PE 8.1 2005Q1 application server. I create a jms resource as jms/myQueue and I can see it using the JNDI browser.
    However, after restarting the application server, my destinations still show up under JMS Destinations & Admin Object Resources, but disappear from the JNDI browser and are unavailable to clients!
    Do I need to perform an addtional step in order to get the appserver to persist these jndi registrations? There appears to be a disconnect between JMS and JNDI. Any help is greatly appreciated.

    JMS has a ForeignJMSProvider config option to do this I believe. 9.0 will also support this more generally.

  • Search Disappears from Menu (after expanding Mini Player)

    Hi there I'm on Android 4.3 mobile using Spotify version 3.1.0.1113.  The Search option disappears from the main top left menu every time I use the app. I have narrowed it down to happening right after expanding the mini-player from the bottom of the screen.  I can open the app and use it normally, but once I click the new mini-player (the new version that allows swiping to change songs) to bring up the main player screen, Search will disappear from the top left menu, leaving just Browse/Activity/Radio/etc.  I can bring back Search by closing the app and reopening it.  I have tried other 3.1 versions, including Betas, and this always happens. Any ideas? Thanks  

    After you search for the artist, *Ctrl click* the arrow after the artist name to see all items by that artist in yoru library, then play and open the mini player.
    Better yet, instead of search, simply turn on the browser (iTunes menu View -> Column browser) then select the Artist to see everything by that artist.

  • Bluetooth disappeared from system preferences and menu bar...

    My bluetooth preferences disappearead from system preferences as well as the menu bar. I discovered this because my bluetooth mighty mouse stopped working. I tried replacing the batteries but nothing happened. I used my trackpad to click on the bluetooth icon on my menu bar and told it to connect to my mouse, which was there in the list. I got the swirling ball and so restarted my computer, when it came back, bluetooth was gone from the menu bar and system preferences, so now I don't know how to reconnect my mouse.
    I tried resetting the PRAM and NVRAM as recommended by another post, I tried it twice as the instructions outline, but I haven't had any success.
    I have tried doing spotlight for bluetooth in system preferences, this takes me to keyboard and mouse, then I get this message:
    "The Bluetooth tab of Keyboard & Mouse preferences is hidden because you don't have a Bluetooth module installed or attached to your computer."
    When I do a spotlight on the entire system, I get a result for bluetooth in system preferences, when I click on that, I get this message:
    "You cannot open “Bluetooth” preferences pane because it is not available to you at this time. You might need to connect a device to your computer to see this preferences pane."
    But, the irony is, that I can't connect a bluetooth device without this option in preferences. Also, in utilities, I remember that there used to be a bluetooth setup assistant, and that is not longer there.
    I realize other threads have come up on this, but I haven't found anything besides deleting the plist, restarting, and resetting the PRAM and NVRAM (whatever that is). I've tried this but haven't been successful so I'm looking for more ideas.
    Dan

    HI Daniel,
    Try deleting this file.
    com.apple.preferencepanes.cache
    ~/Library/Caches.
    Move that file to the Trash and restart your Mac.
    If that doesn't help, download and install the 10.5.8 combo update available here.
    http://support.apple.com/downloads/MacOS_X_10_5_8_ComboUpdate
    It's ok to do this even though you are already running 10.5.8.
    Make sure and repair disk permissions after the installation.
    Quit any open applications/programs. Launch Disk Utility. (Applications/Utilities) Select MacintoshHD in the panel on the left, select the FirstAid tab. Click: Repair Disk Permissions. When it's finished from the Menu Bar, Quit Disk Utility and restart your Mac. If you see a long list of "messages" in the permissions window, it's ok. That can be ignored. As long as you see, "Permissions Repair Complete" when it's finished... you're done. Quit Disk Utility and restart your Mac.
    Carolyn
    Message was edited by: Carolyn Samit

  • Why do new event items disappear from calendar after a few seconds

    Suddenly,new event items disappear from calendar a few seconds (7-30) after creation. This has never been a problem before, and I have used iCal for years. All my old events remain but as of today, when I try to add an event, it stays on the screen for a few seconds, then disappears. I tried entering the events on my iPhone and then syncing, but they went away on my phone as well. Does anyone have an idea of what's happening? Is my iCal out of memory?

    I had success with this method:
    1) make a backup of iCal's database (-> file menu)
    2) revert to that same backup ( " " )

  • Contacts disappeared from phone after iOS 4.2 update

    I updated my iPhone 4 to the new iOS 4.2 and after some contacts disappeared from my phone but are still on my computer. I've tried resetting sync history, I even restored the phone and the same contacts still won't show up. I have a PC that runs Windows 7, I've been using it since September and I never had this issue before.

    Welcome to the discussions,
    did you also try to use the option to replace all contacts on the phone with the ones on the computer during the following sync? You can find this option in the info pane, advanced section.

Maybe you are looking for