Voicemail doesn't pick up!

So I only noticed this once my girlfriend told me she thought I was hanging up on her calls...when I miss a call, it doesn't cut to voicemail. I experimented using my home phone, and noticed that once my Palm stopped ringing and displayed the 'Missed Call' message, my home phone (the other end of the call) kept on ringing, and eventually sounded like the line was picked up and then hung up, followed by the busy signal/dead tone (so in other words, it sounds like I picked up and immediately hung up, even though I didn't even touch my phone).
Whats up with this and how can I fix it?
Post relates to: Treo 650 (Verizon)
This question was solved.
View Solution.

ksm283 wrote:
How do I disconnect from the Verizon network? Wouldn't that make it impossible to get calls?
Yes, just for testing. It would be the same thing you would do when getting on a flight, to go into flight mode: press and hold the red power/end button until the phone disconnects from Verizon. Then call your mobile from a land line or another mobile and see whether voicemail picks up. Press and hold to get back on the network after testing.

Similar Messages

Voicemail message doesn't pick up incoming call.

I have version 6.13 of Skype.
I call my number. The computer responds and I have the option to Accept or Decline. I let it ring. Skype then stops at 20 seconds and does nothing else. My phone keeps ringing and ringing and my voicemail doesn't pick up.
I call again. The computer responds and I have the option to Accept or Decline. I select Decline. Skype stops ringing. My phone keeps ringing and ringing and my voicemail doesn't pick up.
My voicemail is set up to answer after 20 seconds. It is also set up for voicemail to pick up if I am already in a call and/or if I reject an incoming call.
I use my phone for work and I need for voicemail to pick up, so I can call back and they don't think I am ignoring them!
I don't have call forwarding turned on or "follow me" configured (whatever that means).
Any assistance in this matter would be greatly appreciated!

I've been having the same problem for ages, but today finally resolved it.
Warning: I use a Mac, but could not find a thread for a Mac Skype community - so I hope what I did helps all of you who are having problems with Voice Mail.
This is what I did: I set my online status to ONLINE, which on the Mac is an icon in the menu bar at the top of the screen (normally I set my status to INVISIBLE when I'm online). I also made sure in my preferences that calls will be sent to voice mail. After setting my status to ONLINE, the voice mail picked up after 4 rings, just like it used to before all the "improvements" to the app.
I also found that my voice mail message was truncated at the beginning. When I re-recorded it, it took an extra moment for the record function to actually kick in, so I had to fuss with it for awhile before getting a satisfactory recording.
I hope this helps!

I scanned an image and want to use the image trace tool, but it doesn't pick up all the lines. Is there a way to darken the lines before using the image trace tool?

I scanned an image and want to use the image trace tool, but it doesn't pick up all the lines. Is there a way to darken the lines before using the image trace tool? Help!

If the scan is in B&W, then play with the Threshold setting here
If it's in Color, then you will have to open the scan in a Raster editing software (like Photoshop) and play with the Brightness/Contrast settings to make the lines bolder.

File(FTP) Adapter doesn't pick any file from FTP server

Hi All,
This is a strange problem. I am trying to pick all the file from a FTP server using File Name: . . But the file adapter doesn't pick any file from the directory. When I change it to a specific file name eg. ABC.txt then it picks up the file ABC.txt only.
My requirement is to pick up all files in the directory and I just do not seem to understand what is wrong. I have used this wildcard option several times earlier and it always worked fine. But in this case, this does not work.
I changed the FTP server to point to an internal FTP server and it works fine.
I have checked all my parameters and everything looks okay. Like I mentioned earlier, if you specify exact file name, it picks up the file.
Any guess as to what is going on here?

Transport Protocol: FTP
Message Protocol: File
source directory: /test or test ( either one works)
file name: * or . or *.txt nothing works
server: ftp server name
port: 21
data connection: passive
user: ******
pass: ******
connect mode: permanently
transfer mode: text
QOS: exactly once
poll: 10 secs
processing mode: archive ( changed to test and delete as well, but made no difference.)
archive dir: dir path
file type: text
adapter specific attributes:
checked: set adapter specific attributes
and file name.
status: active.

I have 2 Apple ID's. I bought all my music on first one. Now, update/sync doesn't pick up musiuc bc using a new Apple ID.... can i merge them onto my iPhone?

I have 2 Apple ID's (the old one and my newer one - attached to a new email address).
I bought all my music on first one.
Update/sync doesn't pick up music bc using a new Apple ID.... can I merge them onto my iPhone?

No.
Content bought using one Apple ID cannot be merged or transferred to another Apple ID.
All content is forever tied to the Apple ID used to obtain them.

When I plug my iPad into my laptop it doesn't pick it up on iTunes?

When I plug my iPad into my laptop it doesn't pick it up on iTunes?

You did not state what OS you are running ... so for Windows
iOS: Device not recognized in iTunes for Windows - Support - Apple
For Mac OS X
iOS: Device not recognized in iTunes for Mac OS X - Support - Apple
Only for Mac OSX 10.6
Mac OS X v10.6: iOS device not recognized in iTunes after restart

Change Account Workflow in CUP - Doesn't pick up existing values for an Acc

Hi,
When using the change account option available in the CUP(5.3 SP 7), I expected the system to populate the user details as they exist in the provisioning system once I enter the account details that need a change. We have the 'Search' and 'User Details' Data source configured to the same SAP R/3 system.
For eg, when requesting for a new account, I've chosen an Employee Type attribute as 'Non-Employee' (SAP delivered request attribute) and entered some values for my custom attributes .
And when I chose to change the same user account, I notice that the system doesn't pick up the existing values for any of the attributes and render them. For the Employee Type attribute, it shows the default value and for the custom fields, they are shown blank!!!!
It does seem like the user attribute values from R/3 are being picked up and displayed correctly, but the ones from GRC Database are left out.
I believe this to be a bug and does anyone experienced this issue and found a fix????
Thanks,
Anil

Hi Alpesh,
Thanks for your response.
This brings up a basic question on the repository for saving user attribs...ie. does all these need to be saved on R/3? Assuming yes depending on our current configuration(We have the 'Search' and 'User Details' Data source configured to the same SAP R/3 system), do we have a standard field for saving the 'Employee Type' attrib in SAP?. I did perform a field mapping of a custom attirb to one of the SAP fields in the user master, and get it saved during user provisioning. But it doesn't pick it up from there when I perform a change account. Seems it's missing that reverse mapping. And I've chosen the 'Field Type' of the custom filed to Text as to enable free text during new account request.
Hope you may find something more.
Regards,
Anil

Tomcat doesn't pick up the changes to jsp files

My original problem was JAR locking. I changed context.xml files both in conf\ and my application.
jakarta-tomcat-5.5.9\conf\context.xml
<Context reloadable="true" antiResourceLocking="true" antiJARLocking="true">
 <WatchedResource>WEB-INF/web.xml</WatchedResource>
</Context>myApplication\META-INF\context.xml
<Context reloadable="true" antiResourceLocking="true" antiJARLocking="true">
 <WatchedResource>WEB-INF/web.xml</WatchedResource>
</Context>Now I can undeploy without having jarLocking problem.
But now tomcat doesn't pick up the changes to jsp files automatically!!!
I have to undeploy/deploy even I just change jsp files!
What's wrong?

You can't do anything except speak in a different accent. Apple would have to add specific support for different accents in a future iOS update.

When I try to record videos, the camera doesn't pick up my voice. Is it because I have over 1000 pics/vids?? Because Siri can hear me when I talk to her.... It only doesn't work on videos

When I try to record videos, the camera doesn't pick up my voice. Is it because I have over 1000 pics/vids?? Because Siri can hear me when I talk to her.... It only doesn't work on videos

Hi colin3!
It sounds like you could be having an issue with one of the microphones on your iPhone 5. Your iPhone 5 has three microphones that function together and separately, depending on what is using them.
Apple - iPhone 5 - It’s so much more. And so much less, too.
http://www.apple.com/iphone/features/
Enhanced audio on iPhone 5.
Apple EarPods are just the beginning of the improved audio experience on iPhone 5. It’s designed with three microphones: one on the front, one on the back, and one on the bottom. The front and back mics work together to achieve beamforming — a technique that helps iPhone focus on sound from the desired location for clearer audio. New noise-canceling technology reduces background noise. So when you hold iPhone up to your ear in a loud room, you hear what matters most: the voice on the other end.
There is an article available that can help you troubleshoot the issue a little further and can guide you to some next steps. That article can be found here:
iPhone: Hardware troubleshooting
http://support.apple.com/kb/ts2802
Thanks for being a part of the Apple Support Communities!
Regards,
Braden

Z10 doesn't pick up or automatically connect to existing wi-fi networks

Hi guys I recently did the software update and since that day when I get to work I have to turn wi-fi off and then back on and it will connect to the work network. When I get home I have to do the same thing. Prior to the last update it worked fine and connected automatically whenever I got to work or to home. Is there a setting that I'm missing by chance? I have also deleted both networks searched for them and installed them again and still it doesn't pick them up. It's very frustrating that after an update which I thought was an improvement that it actually behaves poorly. Optus actually told me not to do any software updates as they are not needed and interfere with the settings. Please help anybody.

I am having the same problem with by Z10 software release number 10.1.0.273 ; Please help as I cannot connect to WI-FI anywhere , work , airport, restaurants , home!!

IPhone doesn't pick up wifi automatically

Sometimes it does, sometimes it doesn't. Often my iPhone doesn't pick up wifi when I come into a wi-fi zone and stays on GPRS until I go into setting, wifi and then it picks up the network. Sometimes it does it automatically but it's annoying when it doesn't. It sometimes does the same with network signal if you go into a 'No Service' area and then come out of it it often takes a long time to pick up the network signal again. What could be wrong?

These are wi-fi networks your iPhone has connected with previously?
If not, your iPhone won't automatically connect to an available wi-fi network unless your iPhone has successfully connected to the network previously.
You can try resetting network settings at Settings > General > Reset.
This will erase all saved wi-fi networks and settings your iPhone has connected with previously and require manually re-joining every wi-fi network your iPhone has access to when returning within range of such a wi-fi network. This will also reset your cellular network connection.

When I plug my iPad Air in, it doesn't pick up the charger being plugged in.

When I plug my ipad air in, it doesn't pick up the charger until I move the plug around a few times, and when I let it go, it doesn't pick it up anymore.
ive tried using a different brand charger, and I'm now back to using the one that came with an iPod that I got a few months before the iPad.
the charge cord works perfectly fine on the iPod but doesn't work on the iPad.
this has been happening for a few weeks and it's getting really frustrating.
please help.

Please make a Genius Appointment and take it in for service.

My feed reader doesn't pick up all my bookmarks

My feed reader (Brief) doesn't pick up all my feeds; specifically, it doesn't pick up those with dashed squares instead of logos in the label area. what do these squares mean, and how do I get my reader to pick them up?
Thanks.
Roger Blair

After going through my feeds, I discovered that the problem is not as widespread as I thought; there are only two instances, one of which I've documented in the accompanying screenshot. As you can see, two of the "boxed" feeds--"Ask Me Another" and "Wait, Wait...Don't Tell Me"--don't show up in the feed reader (Brief); the third one ("Sunday Puzzle") shows up twice: once with NPR logo (which appears in the feed reader), and once with the box, which doesn't appear. Also, when I delete the "boxed" feed, both feeds disappear, and I have to go back download it again. This apparently only happens with some (not all, by any stretch of the imagination) NPR feeds, and on no other site. Please note that I use Microsoft's "Live Bookmarks" to subscribe to all my feeds.
I hope this information helps. Many thanks
Roger Blair

[SOLVED] Xorg doesn't pick up any input devices from udev

My laptop is an Acer Aspire One D255. With a fresh install of Arch, Xorg doesn't pick up any input devices from udev. The keyboard and trackpad both work in the linux console. Killing gpm has no effect. I would post my xorg log, but it's terribly uninformative. There is no mention of anything evdev or input related other than the standard message:
[222367.704] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
I've tried various tweaks to xorg.conf and udev rules, but nothing seems to have any effects. I don't know if this is related, but xinput refuses to connect to the xserver, so `xinput list` doesn't provide anything useful either.
Has anyone seen this before?
Last edited by redden0t8 (2011-03-11 18:16:58)

Xorg package versions:
http://pastebin.com/Fu2gpdYD
udev is 166-2
Keyboard info:
http://pastebin.com/zkZdFTmW
Trackpad info:
http://pastebin.com/X9sPXcau
Let me know if there is any other info that could be helpful.
EDIT: thought I'd add:
My xorg.conf and udev rules are all stock. I've tried playing around with them to no avail so I'm back to stock settings.
`xorg -configure` produces a broken configuration. It tries to statically configure the keyboard and mouse, but doesn't set "AllowEmptyInput" "false" so I end up with the same problem.
Video works flawlessly out of the box so that's not an issue.
Last edited by redden0t8 (2011-03-11 13:36:21)

Import Server doesn't pick up file

Hello
I am trying to import vendor xml file
I put in the right directory but the server doesn't pick up the file
the service is started
the port/mapping/system config in mdm console has been done
the mdis.ini looks like that :
[GLOBAL]
String Resource Dir=D:\PROGRA1\SAPMDM1.5\IMPORT~1\LangStrings\
Log Dir=D:\PROGRA1\SAPMDM1.5\IMPORT~1\Logs
Version=5560
Server=xxx
Interval=5
Automap Unmapped Value=True
Unmapped Value Handling=Add
Always Use Unmapped Value Handling=False
VXR_MAX=25000
Verbose=0xFFFF
-- Verbose OFF:     0x0000
-- Verbose ON:      0xFFFF
-- FI Verbose:     0x0001
-- XML Verbose:     0x0002
-- MAP Verbose:     0x0004
-- THRD Verbose:    0x0008
-- PARSER Verbose: 0x0010
-- STRUCTX Verbose: 0x0020
-- VALUEX Verbose: 0x0040
-- IMPORTX Verbose: 0x0080
String Resource Dir=C:PROGRA1SAPMDM1.5IMPORT~2LangStrings
Log Dir=Logs
SLD Registration=False
Wily Instrumentation=False
NCS Library Path=D:\PROGRA1\SAPMDM1.5\IMPORT~1\
Wily Instrumentation Level=1
MapScanTopToBottom=False
[CustomersLOCALHOSTMSQL_9_9_4_3]
Chunk Size=50000
No. Of Chunks Proccessed In Parallel=5
Login=Admin
PasswordE=KA9FPAOJG0BK7
Log Protocol Transactions=False
[VendorsLOCALHOSTMSQL_7_9_4_3]
Chunk Size=50000
No. Of Chunks Proccessed In Parallel=5
Login=Admin
PasswordE=KA9FPAOJG0BK7
Log Protocol Transactions=False
what should be the file name in the directory ? could this be the problem ?

Hi Kaushik,
For picking up the file file ready folder you need to do the following steps:
1) Creation of users and assinging password to the users.
2) Creation of maps in import manager for importing the data.
3) Creation of ports. In this you have to mention map name which you have made for importing the data, format of the file present in ready folder and your processing type as automatic.
4) Mention user name and password in the MDIS.ini file. Also mention the time interval.Save this file.
Now you can find that import server is picking up the data from ready folder.
If you are still facing some problems please go through this URL: [http://help.sap.com/saphelp_mdm550/helpdata/en/19/d4301589b54841af17e7c42b4cee49/content.htm]
Hope I am able to solve your problem
Regards
Dilmit Chadha

Voicemail doesn't pick up!

Similar Messages

Maybe you are looking for