VoIP and Data over 1300 Bridge

I have a customer who wants to link 5 out buildings back to the main network. I have proposed using the new 1300 series bridges and have already verified clear line of site from the root location to all remotes.
The customer wants to run VoIP and data on the links. They expect about 3 phones and 3 computers at each location. Each location will have a 3500 series switch powering the 7940 phones.
Is there a maximum number for running the VoIP of a multipoing bridge setup?
I know I will need to setup QoS on the bridges. I just cannot find any documentation to support this setup.
Seth

Thsi document should help explain the Quality requirements for Wireless devices,
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_guide_chapter09186a00802091be.html

Similar Messages

I want to take my apple tv from my home in Canada and us it at the Cabin in the States, but can't seem to get it to set up in the states? It just keeps asking for time and date over and over.

We just bought apple tv for our home in Canada, we also want to use it at our Cabin in Montana. We have internet and can get netflix etc on the Macbook, but don't seem to be able to hook up the Apple TV, it just keeps asking for the Time and Date over and over. Anyone know what we are doing wrong?

Hi There,
Find this here:
https://discussions.apple.com/message/20125520#20125520
Problem lies with IOS 6.0
Restore back to IOS 5.1.1 and set the Location to US you will be ok.

Native VLAN over 1300 bridge

Does the BVI interface work on the native VLAN or always on VLAN1 on a 1300 bridge? If I set a VLAN other than VLAN1 for native will that move the BVI to that VLAN?
Also, does the native vlan have to match at both ends or does it only have local significance? If I had a point to multipoint bridge link, could one remote bridge be set for a different native vlan than another remote bridge?
I have a bridge link that carries two data vlan's and a voice vlan. At the remote end I only have a phone connected to the bridge directly and have configured the phone to be on the correct voice vlan but I need the computer to access a vlan other than the native. I know I cannot configure the phone to have the PC use the proper vlan as it just uses what the bridge tells it is the native.
All network equipment is managed in the vlan1, the native vlan, and user data is on another vlan.
Seth

You cannot configure multiple VLANs on repeater access points. Repeater access points support only the native VLAN.

Time different on VOIP and data network

i have a 5 minute time difference on the data network than the VOIP network.
i started time services on the Pub and changed the router config to use an internal server that synchs with the clock in Boulder.
any ideas?
thanks!

Jerry,
Here is a link for tine service with some recommendations. However I would not use times as when you do an upgrade to CCM or install an SR XNTP will be installed & you will have t time sources fighting for time. Having 2 time clients fighting of the correct time on the servers is a BAD thing!!! I would use XNTP & point all of the Subs to the Pub & point the Pub to the same source that is being utilized by the data network. Please keep in mind that every time you install an SR or upgrade the XNTP config file for all servers will be over written with the default on all nodes, thus you will need to make the appropriate changes after to keep your time in sync.:
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_white_paper0900aecd8037fdb5.shtml
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_configuration_example09186a008009470f.shtml
Mike

T440S to T440s - program and data transfer, OS licensing issue

Hi,
Obviously not able to open these critters up. I have a new T440s that I would like to transfer my programs and data to. Is there a program out there that can do this without having to pull out the hard drive to image?
My current one has Windows 8.1. The new one has Windows 7 with the Windows 8.1 recovery discs. Issue is, I believe that the Windows license is tied to the hardware? Therefore I would have to make a recovery disc set of Windows 7.....then use the Windows 8.1 recovery discs then move my programs and data over.
Windows Easy Transfer does not look like it can do the best job.
I thought about bringing it to the store for them to swap the drives but then worried alot about the whole licensing issue. (not to mention the possible loss of my warranty) Unless if it is done professional and the license could be stripped out of the existing drive and new drive moved to new machine....perhaps a way to get the license keys from the new system somehow.
Thanks in advance.

Hello.
If you look at the bottom of the machines, and they both have the Windows 8 sticker, your machines are licenced and the product key is embedded in the BIOS.
You can use this program: ProduKey to view and write down your keys, but if you use either the Recovery disks or a WIndows 8 Pro retail DVD to reinstall Windows, your key will be picked up automatically by the installation.
For migration of your files, programs and settings, you could simply clone your current WIndows 8.1 installation onto the new drive using, assuming your installation is UEFI and thus your HD is GPT partitioned, Macrium Reflect, which many users here have had a good experience with. That would save you time from having to reinstall Windows on the new machine as well and all you'd have to do is to enter the embedded Windows key of your new machine to activate it.
Macrium Reflect
That's at least one suggestion, but there are many ways to go about this.
Hope this helps.
Cheers!
ThinkPad W540 (20BG) - i7-4800MQ/24GB // ThinkPad T440s (20AQ) - i7-4600U/12GB
ThinkPad T440p (20AW) - i7-4800MQ/16GB // ThinkPad Helix (3698-6EU) - i5-3337U/4GB
ThinkPad W520 (4282-W4Q) - i7-2720QM/32GB // ThinkPad T400 (2767-W1C) - P9500/8GB
ThinkPad T61 (7665-CTO) - T7700/4GB // ThinkPad T60p (8741-C2G) - T7400/4GB

Would Verizon support concurrent voice and data for 4S?

With the absence of 4G in 4S - this would be at least something to be happy about...

I would not be that sure, knowing that Thinderbolt could do it over 3G:
http://phandroid.com/2011/01/26/simultaneous-voice-and-data-over-3g-confirmed-for-htc-thunderbolt/
Sounds like it should be only a matter of enabling it by the carrier, provided the hw supports it.
C'mon VZW, I'll even accept partial data speeds!

Port with multi-vlan for voice and data??

Hi guys,
I've a situation where my VOIP and DATA on a different segments. Voice is 10.x.x.x riding on VLAN 701. And my data is 192.x.x.x riding on VLAN 100.
The problem occur when our receptionist PC have a software installed for call forwarding for our general line. This software need to be on the same vlan with the IP Phone vlan which is 701. If I put her PC on those vlan, she can't access
to our LAN which is vlan 100. So she can't check her email etc.
Can I know what is the options I have? Can I configured multi-vlan for her PC on the switch? We are using Cisco PoE 3560 switch. Thanks.

Hi,
on the L3 switch, you should have an IP address for both VLAN 701 and 100. So, the L3 switch is doing inter-VLAN routing.
This means, unless you have ACL blocking traffic, any device will be able to reach any other device, even on a different VLAN.
And, no matter where you put voice and applications, everything will work anyway.

VoIP over Wireless (bridges/802.11b) Connection

Hi,
I have 2 sites with Voice-enabled routers installed. They are connected to PBX in both sites.
These sites are connected to each other via a 2.4Ghz 802.11b wireless connection using Aironet 350 bridges.
The link is currently used to carry voice only (no data traffic transmitted over the link).
Connection is operating at 11Mbps but configured to fallback to lower speed in case it is needed. Statistics show that connection is operating at 11Mbps for the majority of the time.
Same connection had previously been tested with data traffic and no problem was noticed.
The problem is that when more than 5 simultaneous voice calls (Codec is G729) are transmitted over the link, the voice quality gets degraded.
We have also tried to use the same link for Voice and Data at the same time, we have also noticed that at the 6th call, the quality gets degraded (i.e. with and without data being trasmitted on link at the same time as voice, we are getting choppy voice quality starting the 6th call).
Thanx

You can try using a voice codec which consumes less bandwidth or enable cRTP to reduce bandwidth consumption .
http://www.cisco.com/en/US/tech/tk652/tk698/technologies_tech_note09186a0080094660.shtml

My calendar on my iPhone 4 erases all data over a month old except for recurring events. How Do I get it to keep the info and not erase calendar events?

My calendar on my iPhone 4 erases all data over a month old except for recurring events. How Do I get it to keep the info and not erase calendar events?

Settings>Mail, Contacts, Calendars>Calendars>Sync>All Events.
Note: If you're using a work Exchange account, the administrator my have restricted your options for this setting.

My macbook pro recently got swiped and I lost all my data, problem is, just before it was swiped I set up my new iphone 5 which transferred all my photos and music over which is no longer on the computer. What will happen to my phone if I plug it in?

My macbook pro recently got swiped and I lost all my data, problem is, just before it was swiped I set up my new iphone 5 which transferred all my photos and music over which is no longer on the computer. What will happen to my phone if I plug it in?

I never used icloud before so there is no data to back up from. I just spoke to the apple store and they said that if I do plug it in, all the data will be swiped....is there a program I can use to transfer my data from my phone to computer without loosing it all ???
Renee

My daughter's data has been put on my icloud account. I cannot hook up to the icloud wihtout getting all her info on my phone. i would like to delete the account and start over or find a way to remove her info

Without realizing it, my daughter and I are both using my icloud account for our phones. Now I cannot go to the cloud without importing all of my daughter's data to my phone. Is there any way to remove her data from the icloud account or delete the account and start over? I plan on wiping her phone clean and having her create her own account with her own email address

Be sure she signs out of your account before wiping her phone. Also, make sure Find my iPhone is disabled before you wipe it..
Unfortunately, since you have "merged" her data with yours, you will need to delete each unwanted item individually. If you delete the account, when you sign back in with the same account the same data will be synched back from iCloud.

My Macbook pro was stolen 09/12, the police just returned it to me. I want to remove all the data and start over. Format the drive's etc. I have windows 7 on 1 partion and mountain lion OSX on the apple partition. How is the best way to do this?

My Macbook pro was stolen 09/12, the police just returned it to me. I want to remove all the data and start over. Format the drive's etc. I have windows 7 on 1 partion and mountain lion OSX on the apple partition. How is the best way to do this?

Have a look here...
what-to-do-when-your-hard-drive-is-full.html

How do I delete all data on sync and start over?

When I get my bookmarks the way I want them on my computer and delete the ones I do not want it gets messed up. I have 4 computers on my account and every time I sync it brings up old book marks. I have deleted all book marks from my computer and set up a new sync account then deleted all book marks on my other computers. Then I set up the new sync account on all the computers and still brings up Book marks. There should not be any book marks because I deleted all book marks from all computers before I set up the new account. I have done this 2 times and it they come back. How can I clear all my accounts and start over???????????

To delete all of the data associated with your Firefox sync account:
# Go to [https://accounts.firefox.com/settings Firefox Accounts]
# Login using the information associated with your sync account
# Delete your account
# Signup for a new sync account using the [https://accounts.firefox.com/settings Firefox Accounts] website or directly from Firefox
'''Warning:''' This cannot be undone and will result in the loss of your sync data

I just put a solid state hard drive in my mac book pro and used super duper to copy the hard drive and move the data over to thew new ssd, but most of my music isn't in iTunes when I turned it on? How do I get my music to show up in my new drive?

I just put a solid state hard drive in my mac book pro and used super duper to copy the hard drive and move the data over to thew new ssd, but most of my music isn't in iTunes when I turned it on? How do I get my music to show up in my new drive?

Many thanks lllaass,
The Touch Copy third party software for PC's is the way to go it seems and although the demo is free, if you have over 100 songs then it costs £15 to buy the software which seems not a lot to pay for peace of mind. and restoring your iTunes library back to how it was.
Cheers
http://www.wideanglesoftware.com/touchcopy/index.php?gclid=CODH8dK46bsCFUbKtAod8 VcAQg

Best way to port all Windows XP files, applicaitons and data form my PC over to iMac and how to run those Windows apps on Mac?ns on Mac?

I have a Windows XP machine with apps, files and data. I want to get all that over to my Mac, and also run those apps under Windows XP or even Windows 7 on my Mac. Im wondering:
1. How best to get those files over to my Mac
2. How to run those apps and use my Windows based files/data on my Mac
3. How best to run Windows on my Mac....either partitiion my Mac's hard drive and boot up either Windows or MAC OS, or run some other program where I can easily switch back and forth form Windows to MAC OS, or perhaps get it all on an external hard drive, maybe partition that Windows/MAC OS and boot from that?
Thanks!

I agree you would benefit by using virtualizaiton software. Virtual Box is one alternative the commercial apps for doing virtualization are Parallels and VMWare Fusion which you also might be interested in for their support and updates.
Also you may benefit by book marking and using:
Mac 101 , Switch 101 & Find Out How Video tutorials
For your MS Office apps then I'd STRONGLY recommend using the native Office For Mac versions, you can find these on Amazon for less than $100 and then you can run the apps natively rather than having to lean on MS Windows. Also for your Financial and Tax software you also may want to use OS X apps too, for example I used Quicken for over 20 years (PC mostly and some Mac) but switched to iBank. Also for tax software I have used Quicken's Turbo Tax, this also runs natively on OS X.
In other words for your stated needs I don't see much reason to stay with MS Windows. You may have other considerations, if you do please state them, some may be real issues and some may be easily overcome.

VoIP and Data over 1300 Bridge

Similar Messages

Maybe you are looking for