VOIP phone and airport express

I've been trying to use my old airport express as a remote access point to connect a VOIP phone to my Airport Extreme network. These are both older airports, "pre-N" and from what I've read here, what I'm trying to do won't work.
So, the question is, can I use the new Airport Express(N) to connect the VOIP phone to a Time Capsule(N)? If so, how do I set up the Express? The VOIP phone uses ethernet, and currently works through the LAN on port on my current airport base station.
Thanks.

I've use Netgear adapters and a no name brand from DirectTV. Linksys has them, probably D-Link as well. Best Buy will have several to choose from. About $100-150 for a pair.
Now, your question about whether the "g" Express could deliver an ethernet signal. In normal operation, no. But, if the TC and Express were both configured as part of a WDS (Wireless Distribution Network), the ethernet port becomes active in that event. But...you lose half of the bandwidth on your wireless network. WDS is difficult to configure as well.
The newer Express(n) is much simpler to configure and you won't have the big bandwidth penalty with the "extend a wireless network" setup.
Depending on how your wireless signal strength looks in the office, this will work. But, keep in mind there are far more problems with wireless drops, interference issues, etc. The boards are alive with these types of problems.
I think if it were me, (and this was my business phone), I would go with the ethernet powerline adapters, but make sure you get a return for refund privilege...just in case.

Similar Messages

Cordless phones and airport express

I know that 2.4 Ghz cordless phones interfere with the airport express. Does anyone konw if 5.8 interferes with it. Is 5.8 just a different frequency or is it more powerful that 2.4 and would therefore interfere more.
Thanx

Most 5 GHz phones do not interfere. However there are some 5 GHz phones that use 2.4 GHz for some signalling so those devices can interfere.
...or is it more powerful that 2.4 and would therefore interfere more.
No it operates at a different frequency.

Printer not working with Leopard and Airport Express

Hello!
I have seen that this is a common problem but I've tried several solutions that seemed to work for others but still not for me.
I have a Macbook Pro unibody and airport express with OS X 10.5.6. I used a Samsung CLP-300 wirelessly though my airport express (with Tiger on my older macbook). The printer works fine when it is plugged into my USB on the Macbook but not on the airport.
Here is what I've tried in the past 8 months:
- update the Samsung printer driver
- used "fixairport"
- configured HP IP with airport local address
- spent 2 hours on the phone with apple
None of this seemed to work. The printer will print the first page and then any subsequent pages it gives me an error host message.
If anyone can give me an idea of what did work for them in this situation, or maybe I'm doing something wrong, please let me know. It would be greatly appreciated.
Steph

kelscan, Welcome to the discussion area!
You need to reconfigure your AirPort Express (AX) so that it joins the wireless network provided by the "modem". Follow the directions in KB 302153, AirPort Express: How to join an existing wireless network in client mode.

Airport Extreme and Airport Express conflict and failure

I spent 2.5 hours on the phone with Apple and still could not get my Airport Extreme and Airport Express to function. My Apple TV failed as well:
* Connected AEX through Airport Utility to internet. Airport Utility replaced my old configuration on my LinkSystem router. Green light.
* Checked Apple TV. No connection available. Unplugged cable modem, waited 1 minute and tried again. Apple TV connected. No problem.
* Flashing amber light on Airport Express for Airtunes. Does not show up in wireless device list. I call Apple.
* Reset Express. Still no signal. Connect via Ethernet cable. Reconfigure. Green Light. Music works.
* Check internet connection, in order. Apple TV fails. No connection to server.
* Apple TV reset. No connection. No wireless network found.
* Reset Airport Express. Reconfigure channel specifications. No connection with ATV or Airport Express.
* Disconnect Airport Express. Reconfigure. With ATV disconnected I get Airport Express back. Green light but this time no music. Remote speakers appear on itunes, but no music is transmitted.
* Did a total wireless reset on Extreme, and now both Express and ATV are not working.
Frustrated and dissapointed I disconnected everything put back my 5 year old Linksys router and within 15 seconds both ATV and Airport Express worked flawlessly.
How can this happen? What is wrong with this device? It is my second one in a week. The first one made no wireless connection to my Mac at all.
After sulking for hours I tried again, this time leaving the Express out of the equation and reconfiguring the ATV to take over airtunes. After a reset it did fine. Now I have a pure n signal running at 5hz. ATV works again. So does internet.
Any suggestions? Is there something I did not try?
I tried the Firewall trick, the accept all incoming connections trick, the disabling of the iv6 trick, the join a wireless connection trick, and everything else Apple Care could think of.

Maybe I was not clear enough on my post and configurations,
I had a Linksys before I purchased the airport extreme. My airport express joined the Linksys network for the purpose of airtunes. This worked flawlessly from day one.
Airport Extreme asked in the utility to take over an existing network or replace a router. If you chose this option it adopts all passwords, wpa/2 configurations for security and such.
I chose this option thinking that since it is an apple product it would take over everything and work. My airport express had origianlly been set to join my old Linksys network. Since the airport extreme took over this configuration it should work.
Apple stated many times that there seemed to be a conflict and kept asking me about the placement of my airport extreme.
My Linksys was never part of a bridge or a network within a network. It was removed before the Extreme was ever turned on.
After all the problems and hours of trying with Apple, i find it funny that all I had to do to restore eveything was plug my old Linksys back in and conect all the cables, and bam....it worked.
So what is wrong with the airport extreme, or is there something wrong with itunes 8 and its interface with the express? For whatever reason the extreme cannot make the express and my ATV work at the same time.

Wireless modem and Airport Express.. one at a time

Recently my internet provider upgraded my old plug in modem to a newer wireless model. Now it seems that the current setting allow communication with only one or the other at the same time. If I want to be online with the wireless modem and send my iTunes music via Airport Express to my sound system, no dice. I have to either click on the modem up in the Airport choices to be online and listen to iTunes through the computer speakers, or go offline to listen to music through the sound system and Airport Express.
I'm sure I'm just missing something in preferences or settings somewhere.
Can someone point me in the right direction?
Thanks, and Happy New Year!

No ideas?

How to Set Up Time Capsule With Airport Extreme and Airport Express

Just got a new 1TB Time Capsule. I want it to be the main base station for my network. I already have a network set up with an older Airport Extreme base station and an Airport Express to extend it. I am thinking that rather than setting up the Time Capsule to "join" the old network, the best approach is to disconnect the Airport Extreme and Airport Express and reset them. Then set up the Time Capsule as a brand new network and bring the reset Aiport Extreme and Express onto the new network as if my original network never existed.
Is that the right approach or am I complicating it? Can I just join the Time Capsule to the existing network and still make it the main base station for the network?

evelK wrote:
Just got a new 1TB Time Capsule. I want it to be the main base station for my network. I already have a network set up with an older Airport Extreme base station and an Airport Express to extend it. I am thinking that rather than setting up the Time Capsule to "join" the old network, the best approach is to disconnect the Airport Extreme and Airport Express and reset them. Then set up the Time Capsule as a brand new network and bring the reset Aiport Extreme and Express onto the new network as if my original network never existed.
Is that the right approach or am I complicating it? Can I just join the Time Capsule to the existing network and still make it the main base station for the network?
I'd first use AirPort Utility to "Save a Copy As" of your AirPort Extreme settings. Then disconnect it, connect the Time Capsule in its place, and use AirPort Utility's "Import" function to read those settings. (Both of those functions are under AirPort Utility's "File" menu.) You may have to adjust a few settings. Once you have the Time Capsule working as you want, you can reconfigure your AirPort Extreme unit as you wish.

Can I stream music to apple tv and airport express at the same time?

Does anyone know if I can stream music to both AppleTV and Airport Express (speakers) at the same time?
I have a TV in my living room and external speakers on my deck and want to stream music to both at the same time so I have the same music playing in both rooms - but I can't get an answer on IF I can do both at the same time or it I'd have to select one over the other?
Anyone know?

yes - the built-in music app allows to select one speaker only at the same time.
now i've found the WHAALE Multiroom Player App (http://www.whaale.com) - and it sends directly from the iOS Device to my 6 AirPlay speakers. One of them is an Apple TV...
all "in sync" and without any special hardware and additional software.
And i am able to stream different songs to different rooms...
Just AirPlay speakers - wifi router - WHAALE -> that's easy :-)

I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

I would suggest that you connect the Pioneer to the AirPort Express Base Station using an optical digital audio cable that has a TOSlink connector on one end and a 3.5 mm optical connector (Mini Plug) on the other. You can then connect the Mini Plug end into the AirPort's audio port and the TOSlink end into one of the Pioneer's optical digital audio ports.

Connecting wireless modem and airport express

I currently run internet with an old Motoirola Sideboard cable modem and Airport Express - previous version. All runs well. Now my Optus provider has upgraded my service with a Premium account for higher speed. They have also given me a free wi fi Cisco modem - DPQ3925. How can I replace my old Motorola modem and still maintain Air play etc with my new modem using Airport Express. I need to know exactly wire per wire help - please, if possible - Thanks
Mac

Hi - I have a similar issue.
I have a new macbook pro, ATV (3rd Gen) and AXn (purely for Airplay of itunes).
All three are wirelessly connected to my HG556a Huawei WiFi Router.
The Macbook pro and ATV work fine and can see each other for airplay mirroring and itunes.
The AX connects and comes up in Airport Utility (AU) and itunes shortly after you turn it on, but if you either dont use it or stop using it and switch to ATV or whatever it dissapears from itunes and AU says it cant find it. Randomly the light on the AX stays green the whole time.
I have to switch the AX off and on to get it back working again (i.e. itunes and AU can see it).
Following other forum posts I've set the AX up by hard connecting it to my router, setting a static iP and reserving ports 5353 and 3689 to that address. I've also turned off ipv6 or whatever using the networksettings Terminal code string. I have also repaired permissions with disk utility!
It still dissapears from available options in iTunes and AU. ideas?

Network set up using airport extreme, time capsule and airport express

I have searched for relevant answers but can only find different bits here and there.
My set up is as follows:
I have a Linksys wireless router running a stable wireless network for the other computer users in the house and wish to create an extended, additional network using airport extreme connected to the Linksys by ethernet to create the network and then time capsule close to my Mac Mini on my desktop and airport express at the other end of the house to try and extend the range of the network.
I have been trying for 4 days to set this up but without success. I have tried all of the options mentioned in different posts, using WDS, extending a new network etc. I can get connection between the three devices but monitoring on iStumbler there appears to be little improvement in the strength of the signal, iStumbler also shows the time capsule dropping it's signal totally every 10 or so seconds for a few seconds and then I get a positive signal strength for another ten seconds or so.
Can anyone help, it is driving me insane. I am a recent convert to apple computing and have been hugely impressed with all products until now. The claim that the set up of these wireless products is simple seems to be very exaggerated.
I am happy to provide any relevant system or hardware information.
Thanks in anticipation.

I have an AirPort Extreme acting as a wireless base station, connected to a BT router by ethernet.
Then the correct setting for Connection Sharing on the AirPort Extreme would be "Off (Bridge Mode)".
If I set Connection Sharing to "Share a public IP address", I'm told that: "The DCHP range you have entered conflicts with the WAN IP address of your Apple Wi-Fi base station"
Exactly. You have two routers....The BT device and the AirPort Extreme in series with both of them trying to act as the "main" router when you configure the AirPort this way. That won't work.
Only one can be the main router, and it must be the BT device in your setup. So, the AirPort Extreme....and any other AirPorts on your network must be setup to work in Bridge Mode to allow the network to operate correctly.

Apple TV Inference with Time Capsule and Airport express?

I have recently bought an Apple TV 2, which seem to be working fine, however since installing it on my wireless network both my Time Capsule and Airport Express can't be found. Following some fault finding it seems that when I unplug the Apple TV I can reconfingure the TC and AE.
The TC and AE are configured to join my existing network....and have happy sat there for a few years.
I would really welcome any ideas.
Thanks
R

Welcome to the discussions!
It sounds like you have the basic configuration covered correctly.
You might want to check some settings on the TC:
Wireless Mode would be create a wireless network
"Allow this network to be extended" should be checked
The AX should be set to "extend a wireless network"
The "allow wireless clients" box should be checked
In this configuration, the ethernet port on the AX is active so things should work.
A minor point...Although the TC is a dual band device, the AirPort Express is not. Can you make sure that that the Express is connecting to the "main" network on your TC? The "guest" network cannot be "extended".
If you place your laptop close to the Express and hold down the option key while you click on the AirPort icon, some connection information will be displayed. The MAC address of the device that the laptop is connecting to will be indicated. Make sure that that this is the MAC address of the AX, and not the TC.
Another note...If you have not changed the default "main" network, the radio mode is broadcasting 802.11n only at 5 GHz. These higher frequencies are absorbed by walls, ceilings and any obstructions much more quickly than 2.4 GHz signals. So, if you AX is some distance away, you may not be receiving a strong signal for the device at that location.
If you have a signal strength utility on your laptop (the "bars" at the top of the screen are not a very good indicator of actual signal strength), turn off the AX and take a reading to see what kind of signal the Express is receiving where it is located.
Please post back with your results.

Bt Infinity, HH3 and Airport Express

am thinnking about taking BT infinity. THis apparently needs HH3. Have seen threads about connection problems between HH3 and airport express. (I had similar problems with HH2, so resorted to old BT Voyager)
1. does anyone know if problems with HH3 and airport express can be fixed
2. Can I use BT infinity with a BT Voyager
thanks

Re: "If you get Infinity you will not need the HH3 in the first place you can just connect the Airport Express to the Openreach modem."
No use at all. I don't know what you use your Airport Express for, but mine is used to send music to our hi-fi, and so has to be connected to the hi-fi. Therefore it cannot also be connected to the modem.
This worked fine when I used to get my internet via (whisper quietly) Virgin. But with BT Infinity it would lose its connection every now and then. Apple provided a free replacement but that was no better. Following a few tips (e.g. connect to one's laptop via ethernet cable for setup) I was able to set up a connection eventually, but it still loses connection quite frequently. Interestingly enough, resetting the hub gets it going again, though restarting AE does not!

How to setup ADSL moden router and Airport Express 802.11n (1st Generation) to provide internet and airplay connections to multiple devices?

I have a Netgear wireless ADSL modem router (wireless + four ethernet out ports) that i'd like to connect to a 1st gen Airport Express to create a small home network to provide internet access for a MacBook, iPhone and Apple TV, and to provide Airplay connection to the Apple TV and Airport Express audio output jack.
I'd like to turn off the wireless function of the ADSL modem router, and to have from one of its ethernet out ports an ethernet cable providing internet directly connected to my MacBooks ethernet port.
Then from one of the other ethernet outs on the ADSL modem router an ethernet cable connected to the Airport Express's ethernet port. This would be to provide wireless internet connection for the Apple TV and iPhone via WiFi from the AE.
At the same time as the MacBook is receviing internet soley via the ethernet in port, i'd like it to have WiFi connection to the AE to provide Airplay connection to the Apple TV and the AE's audio out jack.
Is this all possible? How should I go about to configure this? How should the AE's ethernet port be configured?
Any special modes the ADSL modem router or Airport Express should be in? ie bridge or client?
Thanks

On the ADSL modem router web-based interface, should I set any security setting? I think not as there'll be no wireless signal coming from it, only wired ethernet connections to both MacBook and AE. Security should only be set on the AE to prevent someone from accessing its WiFi signal. Is this assumption correct?
These are all correct!
How should I go about setting up security for this network?
First I would recommend that you configure the AirPort Express for WPA2 Personal. This will provide you with the greastest level of security while still providing excellent bandwidth performance.
You would configure wireless security for the Express by using the AirPort Utility on a Mac, PC, or iOS device. Using your MacBook Pro as an example, you would do so as follows:
Run the AirPort Utility.
Select the Express, and then, click on Edit.
Select the Wireless tab to enable it.
Set the Wireless Security option to: WPA2 Personal
Enter the desired password in both the Wireless Password & Verify Password fields. Note: Use of a "strong" password is encourage here. By strong, I mean use a mix of upper/lowercase letters, numbers, & punctuation marks. Try not to use common dictionary words. If you operate your wireless in an area where security is of an utmost concern, I would further suggest that you change the wireless security password every 60-90 days. Also don't forget to change the default AirPort Base Station Administrator password as well.
Click on Update and allow the Express to restart.

Apple TV doesn't show up in iTunes when AirPort Express is running at the same time - Can't play music on both Apple TV and AirPort Express speakers together

Hi there!
I am trying to play music from my Mac on multiple speakers, Apple TV and AirPort Express. But as soon as the AirPort Express station is plugged in, the Apple TV does not show up in iTunes anymore. When trying the same using iPhones Remote app it works perfectly.
Does anyone of you have an idea why iTunes does not show me both Apple TV AND AirPort Express? (it has nothing to to with the IP adress as the adresses are different).
Thanks for any help!

As my english isn't too good I made a screenshot to show you what I mean.
As you can see in the image below iTunes only shows me the computer speakers and the AirPort Express. But at the bottom you can see that iTunes actually recognized 3 different speaker (Mac, AirPort, Apple TV 2). Why does the Apple TV not show up in the multiple speakers window? Any ideas?

I just purchased Apple TV AND AIRPORT EXPRESS. I am questioning if I need it when I already have a Netgear Powerline AV 200 Adapter Kit XAVB2001. Does the Airport Express do the same thing?

I just purchased Apple TV AND AIRPORT EXPRESS. I am questioning if I need it when I already have a Netgear Powerline AV 200 Adapter Kit XAVB2001. Does the Airport Express do the same thing?

Thank you so much. Any specifics I should know about prior to connecting? The goal is to watch Netflix from my iPad or iPhone 5 on my tv (located in different room from where Comcast internet modem is hard wired to main computer in house). Movies would depend on wireless transmission to a smart tv not connected to modem.

VOIP phone and airport express

Similar Messages

Maybe you are looking for