VoIP, Video Polycom over MPLS

Hi
Any one using Vidoe polycom and VoIP over MPLS? We have around 5 offices and they want to use Video Polycom over MPLS. If someone can provide Pro and Con for that and any document or link much appreciate it. Thanks in advance.
Sai

i havnt done polycom over mpls
but i would like to give u hints to consider it
the first think u need to know from the ISP what COS they put in as priorty and how many COS they provide u based on SLA and how match max traffic then they start to drop traffic
the other think is to know how the polycom mark the traffic and u need to calssifiy it and put it in proper calss based on the classes provided by the mpls ISP
good luck
and hope this helpful

Similar Messages

Secondary Site SRST over MPLS

My company has IPT in our HQ. We have a secondary mfg location in the next town that is connected via a point-2-point T1, and we run VoIP over it. We have a PRI for PSTN access at the HQ. The 2nd location had POTS access until someone canceled them feeling they were unnecessary (pros and cons for that) At both locations we have SRST on a 1760-V.
Our location in CA (HQ is in WI) currently has its own PBX which is dying. I wish to roll out VoIP to it over MPLS, which I would then replace the P2P T1 and put it in the MPLS cloud too. I plan NOT to add a voice gateway at the CA location and just put a switch out there and route all calls through WI (Leaving a POTS line for fax and 911).
Management only worry is if the phones go out at the HQ, CA will be stranded. I said SRST would kick in and maintain call processing, until the batteries ran out. Only THEN everything would be down. (The other scenario would be the HQ building is compromised somehow).
Is it possible if a DR plan is in place that if an extended power loss occurs, or the HQ building is destroyed, that call routing could be established through our secondary location; since everything is connected via MPLS? I know POTS lines would need to be reestablished, but could the second WI location run SRST for the CA site?

I am not asking how to do it, just if it is possible down the road some time. This could sell the plan to management if it is possible.

How to priortize video & voice traffic over mpls network

Dear all,
I have taken a 512k link from mpls network containing juniper as core routers, while i am using completely cisco in my network, my query is can i priortize my voice and video traffic over this mpls network i am also using rtp header compression.
plz give me sample config if it is possible.
thanks

hi
if i m not wrong there will be different kinda service offering in general being provided by the SPs.
it falls under 2 main major categories one is managed and the other is unmanaged.
in managed services your SP will honour the marking being done by the customers and the same is being carried throughout(in SP backbone) till reaching the remote destination.
in unmanaged services whatever markings you do at ur end will be remarked or ignored by SP according to the policies followed by them.
you can enquire about this with your SP and you can have the QOS policies configured accordingly.
regds

N70 video call over internet...!

I have a N70 phone with good 3G connection. I need to make a video call through my phone with use of front camera. The call need to be just like yahoo messenger video call what we make by PC.
I'm already use VOIP application such like fring. They don't support video, but chat and voice.
So is it possible to make a video call through my phone. Please give names of the software which provide video call over internet.
Thank you.
BR,
Mahendra

hi there.. i tried to use fring on my n70 but its not working.. can you pls guide for the same

Kernel panics every time (shut down your computer). When it stays on I get blotched video, left-over spots, tearig and then shut down your computer...

I use my PowerPC Quicksilver G4 (2.1), 867 MHz, 1.5 GB standart video card system 10.4.11 to scan (lack of driver for my Mac Pro 10.6.8)
The G4 has been running flawless, now I get kernel panics every time (shut down your computer). When it stays on I get blotched video
left-over spots, tearig and then shut down your computer...
I did all recommended software tests Diskutility, rebuild with DiskWarrior and Apples full Hardware test. Everything comes out fine!
I am at the end of my know how. Thank you for any help
                                                                                                         W.W.
I am attaching the latest crashreport:
Unresolved kernel trap(cpu 0): 0x300 - Data access DAR=0x0000000047AC834E PC=0x0000000000821D3C
Latest crash info for cpu 0:
   Exception state (sv=0x37D2EA00)
      PC=0x00821D3C; MSR=0x00009030; DAR=0x47AC834E; DSISR=0x40000000; LR=0x00821D24; R1=0x21E23B40; XCP=0x0000000C (0x300 - Data access)
      Backtrace:
0x00032E98 0x0081AB20 0x0080AC74 0x002E9A80 0x002EB94C 0x0008C248
         0x00029234 0x000233F8 0x000ABEAC 0x5038514E
      Kernel loadable modules in backtrace (with dependencies):
         com.apple.GeForce(4.1.8)@0x7ff000
            dependency: com.apple.iokit.IOPCIFamily(1.7)@0x491000
            dependency: com.apple.iokit.IOGraphicsFamily(1.4.2)@0x5fc000
            dependency: com.apple.iokit.IONDRVSupport(1.4.2)@0x620000
            dependency: com.apple.NVDAResman(4.1.8)@0x636000
Proceeding back via exception chain:
   Exception state (sv=0x37D2EA00)
      previously dumped as "Latest" state. skipping...
   Exception state (sv=0x38A98780)
      PC=0x9000B348; MSR=0x0200F030; DAR=0x01785000; DSISR=0x42000000; LR=0x9000B29C; R1=0xF0202F20; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.11.0: Wed Oct 10 18:26:00 PDT 2007; root:xnu-792.24.17~1/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0003): 0x300 - Data access
Latest stack backtrace for cpu 0:
      Backtrace:
         0x000954F8 0x00095A10 0x00026898 0x000A8204 0x000ABB80
Proceeding back via exception chain:
   Exception state (sv=0x37D2EA00)
      PC=0x00821D3C; MSR=0x00009030; DAR=0x47AC834E; DSISR=0x40000000; LR=0x00821D24; R1=0x21E23B40; XCP=0x0000000C (0x300 - Data access)
      Backtrace:
0x00032E98 0x0081AB20 0x0080AC74 0x002E9A80 0x002EB94C 0x0008C248
         0x00029234 0x000233F8 0x000ABEAC 0x5038514E
      Kernel loadable modules in backtrace (with dependencies):
         com.apple.GeForce(4.1.8)@0x7ff000
            dependency: com.apple.iokit.IOPCIFamily(1.7)@0x491000
            dependency: com.apple.iokit.IOGraphicsFamily(1.4.2)@0x5fc000
            dependency: com.apple.iokit.IONDRVSupport(1.4.2)@0x620000
            dependency: com.apple.NVDAResman(4.1.8)@0x636000
   Exception state (sv=0x38A98780)
      PC=0x9000B348; MSR=0x0200F030; DAR=0x01785000; DSISR=0x42000000; LR=0x9000B29C; R1=0xF0202F20; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8 Model: PowerMac3,5, BootROM 4.2.5f1, 1 processors, PowerPC G4 (2.1), 867 MHz, 1.5 GB
Graphics: NVIDIA GeForce2 MX, GeForce2 MX, AGP, 32 MB
Memory Module: DIMM0/J21, 512 MB, SDRAM, PC133-333
Memory Module: DIMM1/J22, 512 MB, SDRAM, PC133-333
Memory Module: DIMM2/J23, 512 MB, SDRAM, PC133-333
Modem: Spring, UCJ, V.90, 7.0F, á¸
Network Service: Built-in Ethernet, Ethernet, en0
Parallel ATA Device: WDC WD1200JB-00GVA0, 111.79 GB
Parallel ATA Device: ST3120814A, 111.79 GB
Parallel ATA Device: PIONEER DVD-RW DVR-103
USB Device: Hub in Apple Pro Keyboard, Mitsumi Electric, Up to 12 Mb/sec, 500 mA
USB Device: Apple Optical USB Mouse, Fujitsu Takamisawa Component, Up to 1.5 Mb/sec, 100 mA
USB Device: Apple Pro Keyboard, Mitsumi Electric, Up to 12 Mb/sec, 250 mA

Thank you for your reply BDAqua.
Yes I ran short and the Extended Test. All pass. One of the first things I did is Safe Boot several times I also repaired permissions. Safe boot takes no longer than before the crashes and as long as I stay in safe boot mode it won't crash. What does that mean?I also ran MacJanitor and removed the SCCUZI card Apple put in when I bought the G4 as well as an M-Audio Delta 66 card which I do not use (both) anymore. I also started up on an external firewire drive 10.4.6. It also (crashes) does the same thing.
I was hoping somebody understands the crash report I enclosed? Isn't that suppose to say what went wrong?
Thank you again for your input BDAqua
                                                              W.W.

Voice/video calling over BBM is no longer available for OS 10.3.1.1565

After updating to OS 10.3.1.1565 for my BB Passport voice/video calling over BBM is no
longer available. I CANNOT MAKE VOICE OR VIDEO CALLS OVER BBM neither I CAN RECEIVE CALLS
OVER BBM. I do use voice calling over bbm on a daily basis and I feel like I am now without
my phone!
I did update ALL the application offered for the update. Right now there are NO applications
available for the update - all are up-to-date.
BB World indicates I use BBM 10.6.4.10. I did REFRESH BB World with no changes. Yet NO UPDATES
are offered.
When I select the BBM application in BB World among the list of Installed application it
says in red color "Unavailable for this device".
I see some use BBM 10.6.5.10. Are there troubles with voice/video calling over BBM for
10.6.5.10 & OS 10.3.1.1565?
Maybe the bug is with BB World that is to be updated itself? But it does not offer me to
update one.
Does anyone have an idea how to fix that?
Thanks!
Solved!
Go to Solution.

I wish I new how to update
I have purchased yesterday BB Classic for my wife and also updated OS for it.
BBM works flawlessly with OS 10.3.1.1565 and preinstalled BBM 10.5.15.19. However its also indicates in red that the application is "Unavailable for this device".
Anyone from Blackberry, would you please suggest how to update BBM in my case?! It is that vital for me.
Thanks.

Distribute video output over three monitors (+ another)

Hi there,
I've got a triple beamer setup + a Cinema Display. My Mac Pro has two ATI Radeon HD 2600 XT cards. What I need to do now is use the monitor as an operating monitor and combine/distribute the triple beamers in such a way that I can play one 1920 x 480 video file over all three monitors simultaneously, for an event.
The two ATI 2600 cards are especially in there to be able to do this, but when I try to combine the monitors through display settings or through the Quicktime settings, it just doesn't seem possible. VLC won't play my ProRes 422 material, but I could re-render off course when the video is done.
Is my only option a bloody €200,- video splitter, or can I do this 'the software way?'. I find it so hard to imagine that what I want wouldn't be possible with all the hardware power I've already got! Friendly greetings, Douwe.

If you click the "?" in the "Arrangement" tab of "Displays" system preference, it will tell you how to set three out of the four displays to mirror mode, leaving the fourth separate.

Video Chat over Dial-up Connection

Hi,
Is it possible to have a video chat over a dial-up connection? If it is, I'm interested to hear what is the experience like from anyone who has tried it. Is it acceptable? How about having 3 person AV conference, and one connection is dial-up?
I'm looking at buying an MacBook for my parents so they can chat and see the grandkids but they only have dial-up and getting broadband is not really an option since where they are it's still ridiculously expensive.
Thanks for your replies,
Alex

Hi,
Since I started with iChat in 2003 I have only ever seen one post about a successful iChat Video over Dial-Up.
As I recall it was from Britain to somewhere in Ireland and the Irish end was using IDSN at the time at about 66kbps and that it was late in the day.
The Minimum spec stated is for an Internet connection of 100kbps but iChat will give you an Error message when it detects a Bandwidth or Connection speed less than 50kbps.
Realistically this (above) was a fluke and the answer is NO.
9:28 PM Wednesday; July 16, 2008

Play dvd or quicktime video spread over multiple monitors

Okay, I have a Mac Pro with a 512mb ati radeon with 2x 20" monitors hooked up to it via DVI. What I want to do is watch a DVD or quicktime video spread over both monitors. Not just full screen on one of them, but spread all the way over both so that the center of the video appears in cross of the two monitors. anyone know of anyway or software to do this?

I am not sure about software options...it might work with a hardware device like this, depending on your graphics card capability:
<http://www.matrox.com/graphics/en/gxm/products/dh2go/digital/home.php>
from:
http://discussions.apple.com/message.jspa?messageID=4387166#4387166
Now, if you strech the video across both monitors, how can you multi-task and get any work done???

Ask the Expert:Concepts, Configuration and Troubleshooting Layer 2 MPLS VPN – Any Transport over MPLS (AToM)

With Vignesh R. P.
Welcome to the Cisco Support Community Ask the Expert conversation.This is an opportunity to learn and ask questions about concept, configuration and troubleshooting Layer 2 MPLS VPN - Any Transport over MPLS (AToM) with Vignesh R. P.
Cisco Any Transport over MPLS (AToM) is a solution for transporting Layer 2 packets over an MPLS backbone. It enables Service Providers to supply connectivity between customer sites with existing data link layer (Layer 2) networks via a single, integrated, packet-based network infrastructure: a Cisco MPLS network. Instead of using separate networks with network management environments, service providers can deliver Layer 2 connections over an MPLS backbone. AToM provides a common framework to encapsulate and transport supported Layer 2 traffic types over an MPLS network core.
Vignesh R. P. is a customer support engineer in the Cisco High Touch Technical Support center in Bangalore, India, supporting Cisco's major service provider customers in routing and MPLS technologies. His areas of expertise include routing, switching, and MPLS. Previously at Cisco he worked as a network consulting engineer for enterprise customers. He has been in the networking industry for 8 years and holds CCIE certification in the Routing & Switching and Service Provider tracks.
Remember to use the rating system to let Vignesh know if you have received an adequate response.
Vignesh might not be able to answer each question due to the volume expected during this event. Remember that you can continue the conversation on the Service Provider sub-community discussion forum shortly after the event. This event lasts through through September 21, 2012. Visit this forum often to view responses to your questions and the questions of other community members.

Hi Tenaro,
AToM stands for Any Transport over MPLS and it is Cisco's terminology used for Layer 2 MPLS VPN or Virtual Private Wire Service. It is basically a Layer 2 Point-to-Point Service. AToM basically supports various Layer 2 protocols like Ethernet, HDLC, PPP, ATM and Frame Relay.
The customer routers interconnect with the service provider routers at Layer 2. AToM eliminates the need for the legacy network from the service provider carrying these kinds of traffic and integrates this service into the MPLS network that already transports the MPLS VPN traffic.
AToM is an open standards-based architecture that uses the label switching architecture of MPLS and can be integrated into any network that is running MPLS. The advantage to the customer is that they do not need to change anything. Their routers that are connecting to the service provider routers can still use the same Layer 2 encapsulation type as before and do not need to run an IP routing protocol to the provider edge routers as in the MPLS VPN solution.
The service provider does not need to change anything on the provider (P) routers in the core of the MPLS network. The intelligence to support AToM sits entirely on the PE routers. The core label switching routers (LSRs) only switch labeled packets, whereas the edge LSRs impose and dispose of labels on the Layer 2 frames.
Whereas pseudowire is a connection between the PE routers and emulates a wire that is carrying Layer 2 frames. Pseudowires use tunneling. The Layer 2 frames are encapsulated into a labeled (MPLS) packet. The result is that the specific Layer 2 service—its operation and characteristics—is emulated across a Packet Switched Network.
Another technology that more or less achieves the result of AToM is L2TPV3. In the case of L2TPV3 Layer 2 frames are encapsulated into an IP packet instead of a labelled MPLS packet.
Hope the above explanation helps you. Kindly revert incase of further clarification required.
Thanks & Regards,
Vignesh R P

How to provied Redundancy for VRF MGMT with help of BGP over MPLS(MPBGP)

Hi,
Please find the Network Topology.
This is One Remote site and mamaged by Mgmt office.
All devices on remote site is accessed by MGMT Office. My organisation seek for Redundancy for Managing devices.
My administration is from MGW to R1. I am new to MPLS.
AS u can see in diagram, R1 have 3 VRF(Voice,Signal and MGMT).Currently i have primary link over whitch we are running MPBGP.
Traffic from these VRF goes to this primary link. Currently Secondary link is not connected.
Now my organisation proposed for the secondary link and they want that only traffic from VRF -- MGMT should go through MPLS RTR R2 (the secondary link ) , when the mgmt routes not learned from MPLS RTR R1 (Connected to the SP1 ).
Current R1 config
There is IBGP betweem R1 to both MPLS RTR.
BGP Config
router bgp 64513
synchronization disable
neighbor 10.36.150.1 remote-as 64513
neighbor 10.36.150.1 activate
neighbor 10.36.150.1 update-source loopback1
address-family ipv4 vrf signalling
    redistribute connected
    redistribute static
$
address-family ipv4 vrf voice
    redistribute connected
    redistribute static
$
address-family ipv4 vrf OAM-T
    redistribute connected
    redistribute static
$
address-family vpnv4
    neighbor 10.36.150.1 activate
    neighbor 10.36.150.1 send-community
$
!<ospfv2>
router ospf 100
interface gei-3/3
    network point-to-point
$
network 10.36.150.49 0.0.0.0 area 0.0.0.0 --- loopback ip (Configured)
network 10.36.149.60 0.0.0.3 area 0.0.0.0 ---- p2p ip bet R1 and MPLS R1.(Configured)
network 10.36.149.64 0.0.0.3 area 0.0.0.0 ---- p2p ip bet R1 and MPLS R2. ---------- (till now not configured as secondary link is not connected)
router-id 10.36.150.49
so what configuration need to done at R1 to achiev the redunancy for MGMT vrf ?
if possible please reply with sample configuration.
or
IN MPBGP protocol, where i will apply routing policy to apply as- path prepand    so that Route would be secondary to neighbor.
IGP-OSPF and BGP over MPLS is running.
on Which address-familiy nbr,should i apply, is it in VPNV4 or IPV4 or IPV4 VRF ?
if i want 10.36.128.0/26 prefix should go to Neigbhor MPLS R2, what should i use access-list or Prefix list?
please provide the reply with its config .
thanks in advance,
Regards,
Ajay
Message was edited by: Ajaykumar yadav

Hi,
Please find the Network Topology.
This is One Remote site and mamaged by Mgmt office.
All devices on remote site is accessed by MGMT Office. My organisation seek for Redundancy for Managing devices.
My administration is from MGW to R1. I am new to MPLS.
AS u can see in diagram, R1 have 3 VRF(Voice,Signal and MGMT).Currently i have primary link over whitch we are running MPBGP.
Traffic from these VRF goes to this primary link. Currently Secondary link is not connected.
Now my organisation proposed for the secondary link and they want that only traffic from VRF -- MGMT should go through MPLS RTR R2 (the secondary link ) , when the mgmt routes not learned from MPLS RTR R1 (Connected to the SP1 ).
Current R1 config
There is IBGP betweem R1 to both MPLS RTR.
BGP Config
router bgp 64513
synchronization disable
neighbor 10.36.150.1 remote-as 64513
neighbor 10.36.150.1 activate
neighbor 10.36.150.1 update-source loopback1
address-family ipv4 vrf signalling
    redistribute connected
    redistribute static
$
address-family ipv4 vrf voice
    redistribute connected
    redistribute static
$
address-family ipv4 vrf OAM-T
    redistribute connected
    redistribute static
$
address-family vpnv4
    neighbor 10.36.150.1 activate
    neighbor 10.36.150.1 send-community
$
!<ospfv2>
router ospf 100
interface gei-3/3
    network point-to-point
$
network 10.36.150.49 0.0.0.0 area 0.0.0.0 --- loopback ip (Configured)
network 10.36.149.60 0.0.0.3 area 0.0.0.0 ---- p2p ip bet R1 and MPLS R1.(Configured)
network 10.36.149.64 0.0.0.3 area 0.0.0.0 ---- p2p ip bet R1 and MPLS R2. ---------- (till now not configured as secondary link is not connected)
router-id 10.36.150.49
so what configuration need to done at R1 to achiev the redunancy for MGMT vrf ?
if possible please reply with sample configuration.
or
IN MPBGP protocol, where i will apply routing policy to apply as- path prepand    so that Route would be secondary to neighbor.
IGP-OSPF and BGP over MPLS is running.
on Which address-familiy nbr,should i apply, is it in VPNV4 or IPV4 or IPV4 VRF ?
if i want 10.36.128.0/26 prefix should go to Neigbhor MPLS R2, what should i use access-list or Prefix list?
please provide the reply with its config .
thanks in advance,
Regards,
Ajay
Message was edited by: Ajaykumar yadav

I deleted over 200 self taken videos and over 500 pictures in the Moments window in my photo tab. They deleted but still show in my setting in the About window and I haven't gained any additional storage capacity. What do I do now?

I deleted over 200 self taken videos and over 500 pictures in the Moments window in my photo tab. They deleted but still show in my setting in the Setting/About window and I haven't gained any additional storage capacity. What do I do now? Please help! Thanks in advance for any assistance!!!

Check the Recently Deleted album. Deleted photos will reside there for up to 30 days. This allows all those people who accidently delete photos to recover them, something they couldn't do before. To actually free up the space you might have to delete the photos in the Recently Deleted album.

Images in video become over saturated when exported

When I export the project as an AVI the images in the video become over saturated, ie the skin tone of people becomes bright orange in some cases. Is there a setting to prevent this happening?

andrew
Grand ideas or major duds...let us try the two different tests to see if we can pin point where the issue originates and its cause....
You may want to work from a copy of the problematic project....See File Menu/Save A Copy)
Open your existing project (the one that is yielding your DV AVI 4:3 @ 29.97 interlaced frames per second, and displaying with color issues).
But, do not export this project's Timeline using Publish+Share/Computer/AVI with Presets = DV NTSC Standard as you have been doing, assumed
with no export settings customization under the Advanced Button of the preset.
1. Go to Expert workspace File Menu/Project Archiver and its Archive and Copy options. Project Archive the project with the Copy option. This will result in a "Copied....Folder" saved to the computer hard at the location that you designated. Open the "Copied....Folder" to see copies of the source media that went into the project. These copies will represent all the source media that went into Project Assets whether they were used on the Timeline or not. Open each to determine if there is any color issues with any.
on to second test....
2. Go to Timeline Menu and select and click on Delete Rendered Files to do just that. Next, render the Timeline content by pressing the Enter key of the computer main keyboard. All video previews generated from Timeline rendering of a SD project are DV AVI files, be the files being previewed photos or videos.
Next, go to the Adobe Premiere Elements Preview Files Folder (by default in Windows' Document/Adobe/Premiere Elements/12.0) and open that folder. Play back the preview files there to determine if they have color flaws.
Please let us know the outcome.
Thanks.
ATR

How Smooth Should Flash Video Play over a 6Mbps DSL Connection?

Hello,
I am noticing a lot of stuttering on my Flash videos viewed over the internet, Win 7 64bit and IE 8, Opera & Chrome.
Here is a link to some tests - http://watchmymvp.com/Encoding%20Test/EncodingTest.htm
Please give some feedback on your playback experience if you would!
Some background:
I am a video producer who shoots, edits, encodes and manages a few websites. I am very familiar with bitrates and encoding.
The videos I am seeing stuttering on are created from HD content and were encoded in Adobe Media Encoder at a bitrate from 775kbps down to 400kbps. When I play these through my 6meg DSL connection there is a constant random stutter like the video is stuggling with a low buffer. This happens even after the download bar shows the entire video is downloaded.
So am I expecting too much from Flash video? Will it always be an "internet" experience and not smooth?
When I double-click the .swf files in Windows Explorer they play just fine, very smooth. Maybe a SWF Publishing setting?
The Flash player is the latest which was uninstalled and re-installed
Thanks!

Hello Vicente, thanks for your reply.
So the videos did not show stuttering when you watched them? Could I ask what your computer specs are? - Mac/PC, browser etc...
I get a random stutter which shows up more when there is camera movement.
I am trying to track down why this is happening when the .swf file played locally plays perfectly.
Since I an in the video industry, I would like these files to play as if they are on a television is that is possible.
Thanks for your input.

Point to Mulipoint L2VPN trunks over MPLS

Can we have trunk between more than 2 CE over MPLS in short we are looking for the point to multipoint MPLS L2 VPN where more than 2 CE will share the common ethernet segment over MPLS to share the vlan database
Let me give more info @ solution which we are trying find out
CE1,CE2,CE3 & CE4 are the core switches at respective location, we are looking for the same vlan database between these core switches over the MPLS
CE1 will be connected to PE1
CE2 will be connected to PE2
CE3 will be connected to PE3
CE4 will be connected to PE4
so can we have the L2 vpn between CE1,CE2,CE3 & CE4 where the interface connected to respective PE's will be TRUNK ?

hi
thanks for the pdf, I had tried the VPLS earlier. the circuit are coming up but I am not able to ping between CE's Vlan ip address although VC are up
PE end config
interface GigabitEthernet1/35
description L2 Connectivity to KBL039SW1 (TEMP)
switchport
switchport access vlan 100
switchport mode dot1q-tunnel
l2protocol-tunnel cdp
CE-1 end config
interface FastEthernet1/0/48
switchport trunk encapsulation dot1q
switchport mode trunk
end
int vlan 100
ip address 10.10.10.1 255.255.255.0
other end vlan 100 ip address is 10.10.10.2 but not able to ping this ip address from CE-1
any guess what cpuld be the problem?

VoIP, Video Polycom over MPLS

Similar Messages

Maybe you are looking for