Volume will NOT mount

We have much the same issue as others here in other threads have spoken about - after a reboot a raid volume will not mount.
Disk Utility can 'see' the drive and array, but will not mount it. RAID Admin reports no problems. I tried updating the firmware to no avail.
Then I tried a new FC card in the server, a different controller card in the xRAID, different cables and connecting the FC cable to a different XServe. No mount with any of these attempts.
XServe 2 ea 2.3Ghz G5, 2GB RAM, 1 80GB drive (cluster node config)
OSX Server 10.3.9
7 ea 180GB drives, RAID5; 1 TB array
RAID Admin 1.5 (controller firmware - now: 1.5/1.50f)
Any ideas what to try next? And no we don't have 100% backups, close but no... ;-( so any ideas worth trying appreciated!
Tks, Mark

Mark,
We recently had a similar problem. We have an XServe RAID fully populated -- split into 2 volumes. One volume would mount the other would not (after a reboot). Tried swapping fibre channel cables, re-seating fibre channel cards, etc. Our solution was replacing the PCI-Fibre card in the XServe.
Another thing we have had happen is, after reboot, one volume mounts and the other mounts about 15 mins later -- after completing fsck.
Hope this helps.
--Bonnie

Similar Messages

Time Machine backup volume will not mount

Once I goy Time Machine up and running over almost two years ago, I have had little cause for concern. A few lengthy backups here and there but I have been able to restore without any problems whatsoever. It has been extremely useful many times.
A couple of days ago, I noticed that the backup volume was not mounted (I backup to one of my four internal drives) and launched Time Machine. I got the error:
The storage location for Time Machine backups can't be found.
When I run Disk Utility the generic disk icon is in the left hand pane but not the volume. None of the tasks are available except Erase and Partition - there is no option to Verify Disk, Repair Disk, Verify Disk Permissions or Repair Disk Permissions.
According to my logs, the last backup at 18:12 on 20th November was successful. I didn't notice that the volume had not mounted the until the next day.
I'm very concerned that I have lost almost two years of data security. Is there any way I can repair the disk or recover the backups?
Thanks.

If Disk Utility can't see any partitions, it's not good.
First, turn TM off.
Then try ejecting, disconnecting and powering the drive off for a few minutes, then reattaching it. Then try again with Disk Utility. If still no help, the drive is likely dead.
There's a very small chance that +Disk Warrior+ (version 4.1.1 or 4.2 only), or another heavy-duty disk repair app can fix it, if you already have one. But I wouldn't suggest spending the $$ for one unless you think you'll need it in the future -- DW is about $100.
Most likely, your disk is dead. There's a small chance that a +Data Recovery+ app such as +Data Rescue+ can recover some of the data. Check via Google, VersionTracker.com, or MacUpdate.com for +Data Recovery.+ There are services and apps, none cheap. Some of the apps have a free demo or test mode that will tell you if there's anything that can be recovered, and perhaps actually recover a single file; then you pay for it and recover whatever else can be recovered. You'll need another external disk to receive the recovered items.
You won't get the normal Time Machine folder structure, though, just "raw" files. Even if you do recover files, you'll most likely have to figure out what goes where and copy them to the right places manually.
So I'd suggest immediately getting a new drive and doing a new TM backup to it, so you have something. Put a second partition on it that you can use for the recovered files if and when you do that.
If those are your only backups, I'd recommend getting a second external, perhaps a portable one, and using CarbonCopyCloner or SuperDuper to make a full "bootable clone" to it, then take it to your safe deposit box, workplace, relative's house, or other secure location. And/or, you might want to look at Mozy, Carbonite, or other online backup services.

Network drives volumes will not mount

Hi can anyone help me. At my wits end here. Have upgraded 2 machines in our office. 1 Intel Pro mac and 1 Intel iMac, upto 10.6.6
Problem is now when i log onto the ehternet network server drives or random LOCAL USB drives (basically anything external) the connecting machines restart the desktop environment and refuse to mount the drive or folder in question, sometimes it can be infinite loop style reload of the desktop until it finds what its looking for or not. Not all the time just occasionally. Have re installed the combo update but still not fixed it. Could it be a faulty Snow Leopard disc?
Should have mentioned that the server machine is running 10.4 and was running perfectly with the machines on 10.5, so presuming its not that rather the snow leopard upgrade..
Message was edited by: smuuudge

I am having the same issue at our school district. If i wipe out the account and network folder, then recreate it individually it works on both Mac and Windows. So definitely on the server end.

Xsan 4 will not mount volume on client

I recently upgraded my MDC and my client computer to Yosemite. I went through the migration process the best I could and created a Configuration Profile on my MDC for my client computer. I installed the profile successfully but the volume will not mount on the client computer. On the client computer within Profiles, the Xsan Configuration Profile has in red "Unsigned" underneath it, is that what is causing the problem?
Also a few notes: there are two other client computers that haven't been upgraded and are running Maverick and the volume does mount to those computers. The volume is also mounted on the MDC and if I go to Disk Utilities on the client computer I do see the volume, just not mounted.
Any help would be great! Thank you.

Thank you Claudio,
After doing much research and testing I believe you are onto something with my fsmpm or my .auth_secret file not being created. After using Server.app on the MDC I used the configure profile within Server.app. After installing the profile on my client computer it didn't mount and when looking within the Library/Preferences/Xsan folder there was no files (including the hidden .auth_secret file). So I then I used the web profile interface to create the configuration profile and this time it installed the fsnameservers and config.plist files but not the hidden auth_secret file and still no mount.
To answer some of you questions, I did try several times the "sudo xsanctl mount Volume Name" but had no success. I was previously running 10.9 on the MDC and my client computer. I am not sure if the MDC already had an Open Directory Master before upgrading and I did have a little bit of problems activating Xsan, because some of my DNS settings had changed. I got that all squared away and Xsan started working.
The reason I believe it is a fsmpm issue is because when I executed the command "sudo xsanctl i" (views the volumes connected to Xsan) I go a message reading "fsmpm not running error3". So after reading this forum Xsan: "fsmpm not running" message in Xsan Admin - Apple Support I copied the .auth_secret from the MDC to my client and still no mount. I tried again with all the files within Library/Preferences/Xsan folder and nothing. I then got the .auth_secret file from another client computer running 10.9 and still no mount, BUT when I copied all the files within the 10.9 client's Library/Preferences/Xsan the volume appeared! YEAH! But I'm not sure if this is a fix I should be happy with or continue to figure out why its not working the proper way? That way in the future I'm not running into this issue over and over again.
So I need to figure out either how to get my fsmpn running in 10.10 or figure out why my my Server.app on the MDC won't create the auth_sect file. I read somewhere that within the Xsan screen in the Sever app it should show the Authentication Secret, but I do not see this on my Xsan screen. Should it be there and if so is this where my problem steams from? Any thoughts? Thank you so much!

Xsan will not mount on clients

Xsan updated recently to 1.4. Problem started on 1.3 Working fine until reboot of one of the client computers. Now Xsan volume will not mount on any client. Updated to 1.4, ran cvfsck. Still no go. Volume is over 90%. I have read that this may cause issues. How can I get files off if I cannot mount? Thanks!

Try the following:
From finder -->Go --> Go to folder --> /Volumes
Delete the alias for the XSAN volume you want to mount.
For whatever reason the alias sticks even if the volume was unmounted. Below is an explanation from Apple.
Xsan mounts will fail if they have the same name
Xsan will not mount any volume that has the same name as any existing volume or folder located at /Volumes/.
Unlike some mounting mechanisms that automatically resolve name conflicts (for example, the Finder will append characters to each mounted volume name), the Xsan backend agent simply won't mount the volumes.
To avoid this issue, create a unique name for each volume to be mounted.

My Ipod 4th Gen will not mount into Itunes

Please anyone with technical knowledge HELP ME.
The basic problem is that my 4th Generation Ipod will not mount into Itunes.
Let me tell you what I have done so far this includes all the R's, I have also followed the advice of reinstalling itunes and Quicktime I have also tried backwards installing to version 6 (at present I have upgraded to version 7.0.2). The ipod is visible in Windows and I still am able to use it as disk as I have programs I am using off it.
I have tried a fifth gen and also an Ipod mini and both mount onto my Itunes.
I have tried to reinstall the Ipod software, however the previous ipod updates do not work and as the Ipod cannot be mounted I cannot use Itunes to update it as it is not visible.
I have also run the Ipod Diagnostic in Itunes and everything seems fine (I have included the report if anyone can please understand it)and at the very bottom it states that the Ipod is truly Mounted. WELL ITS NOT
I really am getting desperate now as this is the same on both my Desktop and Laptop and I am getting very close to throwing the whole thing out along with all the rest of my computer equipment.
Thanks a lot
DIAGNOSTIC REPORT
Microsoft Windows XP Home Edition Service Pack 2 (Build 2600)
FUJITSU SIEMENS AMILO PRO V2030
iTunes 7.0.2.16
iPodService 7.0.2.16 is currently running.
iTunesHelper 7.0.2.16 is currently running.
Current user is an administrator.
Connected Storage Devices:
IDE\DiskFUJITSUMHV2040BH______________________00000025, Bus Type ATA, Bus Address [0,0]
USBSTOR\DiskApple__iPod___________1.62, Bus Type USB
Universal Serial Bus Controllers:
VIA Rev 5 or later USB Universal Host Controller, PCI bus 0, device 16, function 0. Device is working properly.
VIA USB Enhanced Host Controller, PCI bus 0, device 16, function 4. Device is working properly.
IEEE 1394 Host Controllers:
Texas Instruments OHCI Compliant IEEE 1394 Host Controller, PCI bus 0, device 12, function 2. Device is working properly.
Connected Device Information
PAUL'S IPOD (E:\), iPod with Click Wheel running firmware version 3.1.1
Serial Number: JQ447113PQ7
Bus Speed: 61440
The last connected iPod serial number: JQ524ER2S41.
The iPod Service Logging Information:
[SERVICE: 0xDA8,09:16:59 INFO] Started C:\Program Files\iPod\bin\iPodService.exe (Sat Nov 18 09:16:59 2006)
[SERVICE: 0xDA8,09:16:59 INFO] ##### iPodService starting as a service, version: 7.0.2.16
[SERVICE: 0xDB8,09:17:00 INFO] Got signaled to go ahead... Starting device manager!
[SERVICE: 0x4F0,09:17:00 INFO] Listener Window created
[SERVICE: 0xDB8,09:17:02 INFO] [InterfaceArrival] \\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0xDB8,09:17:02 INFO] device \\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0xDB8,09:17:02 INFO] device is an iPod
[SERVICE: 0xDB8,09:17:02 INFO] type 0x7 drive 0x1 partition 0x0
[SERVICE: 0xDB8,09:17:08 INFO] [-1] set waiting to mount = 1
[SERVICE: 0xDB8,09:17:08 INFO] [1] Assigning session 0
[SERVICE: 0xDB8,09:17:08 INFO] [1] added device interface "\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}" to m_objDeviceNameMap
[SERVICE: 0xDB8,09:17:08 INFO] [1] added state machine 1 to m_objDeviceIdMap
[SERVICE: 0xDB8,09:17:08 INFO] [1] added device number 1 to m_objDeviceNumberMap
[SERVICE: 0xDB8,09:17:08 INFO] [1] added device interface "\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}" to m_vctDeviceInterfaces
[SERVICE: 0xDB8,09:17:08 INFO] [1] input #0 from src #0
[SERVICE: 0xD24,09:17:08 INFO] [1] input #0
[SERVICE: 0xD24,09:17:08 INFO] [MACHINE 1 INPUT #0] - (HDW) Interface Arrival
[SERVICE: 0xD24,09:17:08 INFO] [1] progress state is 2, Waiting to mount = 1
[SERVICE: 0xD24,09:17:08 INFO] [1] progress is now 2
[SERVICE: 0xD24,09:17:08 INFO] [1] progress is now 2
[SERVICE: 0xD24,09:17:08 INFO] [MACHINE 1 TRANSITION] - {Unknown} ==> {Connected}
[SERVICE: 0xD24,09:17:08 INFO] [MACHINE 1 ACTIONS] - {Connected}
[SERVICE: 0xD24,09:17:08 INFO] [1] SCSI Inquiry attempt #0
[SERVICE: 0xD24,09:17:08 INFO] VendorId: Apple
[SERVICE: 0xD24,09:17:08 INFO] ProductId: iPod
[SERVICE: 0xD24,09:17:08 INFO] revision: 1.62
[SERVICE: 0xD24,09:17:08 INFO] vendor bytes:
[SERVICE: 0xD24,09:17:08 INFO] 02 01 00 00 00 00 00 00 00 05 00 13 12 00 00 00 00 00 00 00
[SERVICE: 0xD24,09:17:08 INFO] [1] firmware version: 1.62 (0x13E)
[SERVICE: 0xD24,09:17:08 INFO] [1] Power State: Not Powered
[SERVICE: 0xD24,09:17:08 INFO] [1] Checkpoint attempt #0
[SERVICE: 0xD24,09:17:08 ERROR] Did not find first letter of stage
[SERVICE: 0xD24,09:17:08 INFO] [1] serial number 000A270002BF5F21
[SERVICE: 0xD24,09:17:08 INFO] [1] *** CONNECTED - Sending event out, device session 0.
[SERVICE: 0x4F0,09:17:11 INFO] [SIMULATED VOLUME ARRIVAL] generating volume mount for \\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0x4F0,09:17:11 INFO] [VolumeArrive] mask = 0x1C
[SERVICE: 0x4F0,09:17:11 INFO] looking up device # for \\.\E:
[SERVICE: 0x4F0,09:17:11 INFO] type 0x7 drive 0x1 partition 0x1
[SERVICE: 0x4F0,09:17:11 INFO] iTunes device #1 found with drive letter E, mask 0x10
[SERVICE: 0x4F0,09:17:11 INFO] [1] set waiting to mount = 0
[SERVICE: 0x4F0,09:17:11 INFO] [1] input #1 from src #0
[SERVICE: 0x52C,09:17:11 INFO] [1] input #1
[SERVICE: 0x4F0,09:17:11 INFO] looking up device # for \\.\D:
[SERVICE: 0x4F0,09:17:11 INFO] type 0x2 drive 0x0 partition 0xffffffff
[SERVICE: 0x4F0,09:17:11 INFO] [SIMULATED INTERFACE ARRIVAL] generating connect event for device 0
[SERVICE: 0x4F0,09:17:11 INFO] looking up device # for \\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0x4F0,09:17:11 INFO] type 0x7 drive 0x1 partition 0x0
[SERVICE: 0xDB8,09:17:11 INFO] [VolumeArrive] mask = 0x1C
[SERVICE: 0xDB8,09:17:11 INFO] looking up device # for \\.\E:
[SERVICE: 0xDB8,09:17:11 INFO] type 0x7 drive 0x1 partition 0x1
[SERVICE: 0xDB8,09:17:11 INFO] iTunes device #1 found with drive letter E, mask 0x10
[SERVICE: 0xDB8,09:17:11 INFO] [1] set waiting to mount = 0
[SERVICE: 0xDB8,09:17:11 INFO] [1] input #2 from src #0
[SERVICE: 0x4EC,09:17:11 INFO] [1] input #2
[SERVICE: 0xDB8,09:17:11 INFO] looking up device # for \\.\D:
[SERVICE: 0xDB8,09:17:11 INFO] type 0x2 drive 0x0 partition 0xffffffff
[SERVICE: 0xDB8,09:17:11 INFO] [SIMULATED INTERFACE ARRIVAL] generating connect event for device 0
[SERVICE: 0x52C,09:17:11 INFO] [MACHINE 1 INPUT #1] - (HDW) Volume Mount
[SERVICE: 0x52C,09:17:11 INFO] [MACHINE 1 TRANSITION] - {Connected} ==> {Mounted}
[SERVICE: 0xDB8,09:17:11 INFO] looking up device # for \\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0xDB8,09:17:11 INFO] type 0x7 drive 0x1 partition 0x0
[SERVICE: 0x52C,09:17:11 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0x52C,09:17:11 INFO] [MACHINE 1 ACTIONS] - {Mounted}
[SERVICE: 0x52C,09:17:11 INFO] [1] progress state is 2, Waiting to mount = 0
[SERVICE: 0x52C,09:17:11 INFO] [1] progress state is 2, Waiting to mount = 0
[SERVICE: 0x52C,09:17:14 ERROR] Did not find first letter of stage
[SERVICE: 0x52C,09:17:15 INFO] [1] OS says filesystem is FAT32
[SERVICE: 0x52C,09:17:16 INFO] [1] ===== iPod Touch Wheel =====
[SERVICE: 0x52C,09:17:16 INFO] [1] progress state is 2, Waiting to mount = 0
[SERVICE: 0x52C,09:17:16 INFO] 9:17:16, year 2006, day of yr. 321, GMT offset 0 isDST 0
[SERVICE: 0x52C,09:17:16 INFO] [1] progress is now 0
[SERVICE: 0x52C,09:17:18 INFO] [1] *** MOUNTED - Sending event out, device session 0.
[SERVICE: 0x52C,09:17:18 INFO] [1] Auto-launch iTunes DISABLED
[SERVICE: 0x4EC,09:17:18 INFO] [MACHINE 1 INPUT #2] - (HDW) Volume Mount
[SERVICE: 0x4EC,09:17:18 INFO] ** CItunesDevice::HandleHardwareInput()
[SERVICE: 0x4F0,09:18:21 INFO] [DevNodesChanged]
[SERVICE: 0x4F0,09:18:21 INFO] [1] input #3 from src #0
[SERVICE: 0xD24,09:18:21 INFO] [1] input #3
[SERVICE: 0x4F0,09:18:21 INFO] [DevNodesChanged]
[SERVICE: 0x4F0,09:18:21 INFO] [1] input #4 from src #0
[SERVICE: 0x4EC,09:18:21 INFO] [1] input #4
[SERVICE: 0x4F0,09:18:21 INFO] [DevNodesChanged]
[SERVICE: 0x4F0,09:18:21 INFO] [1] input #5 from src #0
[SERVICE: 0x52C,09:18:21 INFO] [1] input #5
[SERVICE: 0xD24,09:18:22 INFO] [MACHINE 1 INPUT #3] - (HDW) CheckDevNode
[SERVICE: 0xD24,09:18:23 INFO] Connection Detection Status - 0x1806002, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xD24,09:18:23 INFO] * CItunesDevice::HandleHardwareInput()
[SERVICE: 0xD24,09:18:23 INFO] [1] progress is now 1
[SERVICE: 0x4EC,09:18:23 INFO] [MACHINE 1 INPUT #4] - (HDW) CheckDevNode
[SERVICE: 0xD24,09:18:24 INFO] [MACHINE 1 TRANSITION] - {Mounted} ==> {Unknown}
[SERVICE: 0x4EC,09:18:24 INFO] Connection Detection Status - 0x1806002, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0x4EC,09:18:24 INFO] * CItunesDevice::HandleHardwareInput()
[SERVICE: 0x52C,09:18:24 INFO] [MACHINE 1 INPUT #5] - (HDW) CheckDevNode
[SERVICE: 0xD24,09:18:24 INFO] [MACHINE 1 ACTIONS] - {Unknown}
[SERVICE: 0x52C,09:18:24 INFO] Connection Detection Status - 0x1806400, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0x52C,09:18:24 INFO] * CItunesDevice::HandleHardwareInput()
[SERVICE: 0xD24,09:18:24 INFO] Connection Detection Status - 0x1806400, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xD24,09:18:24 INFO] [1] *** DISCONNECTED - Sending event out, device session 0.
[SERVICE: 0xD24,09:18:24 INFO] [1] progress is now 0
[SERVICE: 0xD24,09:18:24 INFO] [1] progress state is 0, Waiting to mount = 0
[SERVICE: 0x4F0,09:18:38 INFO] [VolumeRemoved] existing mask 0x10, arrive mask 0x10
[SERVICE: 0x4F0,09:18:38 INFO] [1] value = 1
[SERVICE: 0x4F0,09:18:38 INFO] [1] input #6 from src #0
[SERVICE: 0x4EC,09:18:38 INFO] [1] input #6
[SERVICE: 0x4EC,09:18:38 INFO] [MACHINE 1 INPUT #6] - (HDW) Volume Unmount
[SERVICE: 0x4EC,09:18:38 INFO] [1] progress is now 3
[SERVICE: 0x4EC,09:18:38 INFO] [1] Setting progress to 3
[SERVICE: 0x4EC,09:18:38 INFO] * CItunesDevice::HandleHardwareInput()
[SERVICE: 0x4F0,09:18:38 INFO] [InterfaceRemoved]
[SERVICE: 0x4F0,09:18:38 INFO] [1] value = 0
[SERVICE: 0x4F0,09:18:38 INFO] removed device number 1 from m_objDeviceNumberMap
[SERVICE: 0x4F0,09:18:38 INFO] [1] input #7 from src #0
[SERVICE: 0x52C,09:18:38 INFO] [1] input #7
[SERVICE: 0x4F0,09:18:38 INFO] [DevNodesChanged]
[SERVICE: 0x4F0,09:18:38 INFO] [1] Progress state is 3, Waiting to disconnect = 0
[SERVICE: 0x4F0,09:18:38 ERROR] device number 0 exists, but isn't in m_objDeviceNumberMap!
[SERVICE: 0x4F0,09:18:38 INFO] removed device interface "\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}" from m_vctDeviceInterfaces
[SERVICE: 0x4F0,09:18:38 INFO] [1] input #8 from src #0
[SERVICE: 0xD24,09:18:38 INFO] [1] input #8
[SERVICE: 0x52C,09:18:38 INFO] [MACHINE 1 INPUT #7] - (HDW) Interface Removal
[SERVICE: 0x52C,09:18:38 INFO] * CItunesDevice::HandleHardwareInput()
[SERVICE: 0xD24,09:18:38 INFO] [MACHINE 1 INPUT #8] - (HDW) CheckDevNode
[SERVICE: 0xD24,09:18:38 INFO] Connection Detection Status - 0x1806400, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xD24,09:18:38 INFO] * CItunesDevice::HandleHardwareInput()
[SERVICE: 0x4F0,09:18:39 INFO] [DevNodesChanged]
[SERVICE: 0x4F0,09:18:39 INFO] [1] input #9 from src #0
[SERVICE: 0x4EC,09:18:39 INFO] [1] input #9
[SERVICE: 0x4EC,09:18:39 INFO] [MACHINE 1 INPUT #9] - (HDW) CheckDevNode
[SERVICE: 0x4EC,09:18:39 INFO] Connection Detection Status - 0x1806400, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0x4EC,09:18:39 INFO] * CItunesDevice::HandleHardwareInput()
[SERVICE: 0x4F0,09:18:48 INFO] [DevNodesChanged]
[SERVICE: 0x4F0,09:18:48 INFO] [1] input #10 from src #0
[SERVICE: 0x52C,09:18:48 INFO] [1] input #10
[SERVICE: 0x4F0,09:18:48 INFO] [DevNodesChanged]
[SERVICE: 0x4F0,09:18:48 INFO] [1] input #11 from src #0
[SERVICE: 0xD24,09:18:48 INFO] [1] input #11
[SERVICE: 0x52C,09:18:49 INFO] [MACHINE 1 INPUT #10] - (HDW) CheckDevNode
[SERVICE: 0x52C,09:18:49 INFO] * CItunesDevice::HandleHardwareInput()
[SERVICE: 0xD24,09:18:49 INFO] [MACHINE 1 INPUT #11] - (HDW) CheckDevNode
[SERVICE: 0xD24,09:18:49 INFO] * CItunesDevice::HandleHardwareInput()
[SERVICE: 0x4F0,09:34:58 INFO] [DevNodesChanged]
[SERVICE: 0x4F0,09:34:58 INFO] [1] input #12 from src #0
[SERVICE: 0x4EC,09:34:59 INFO] [1] input #12
[SERVICE: 0x4EC,09:34:59 INFO] [MACHINE 1 INPUT #12] - (HDW) CheckDevNode
[SERVICE: 0x4EC,09:35:00 INFO] * CItunesDevice::HandleHardwareInput()
[SERVICE: 0x4F0,09:39:01 INFO] [DevNodesChanged]
[SERVICE: 0x4F0,09:39:01 INFO] [1] input #13 from src #0
[SERVICE: 0x52C,09:39:01 INFO] [1] input #13
[SERVICE: 0x52C,09:39:02 INFO] [MACHINE 1 INPUT #13] - (HDW) CheckDevNode
[SERVICE: 0x52C,09:39:02 INFO] * CItunesDevice::HandleHardwareInput()
[SERVICE: 0x4F0,09:39:02 INFO] [DevNodesChanged]
[SERVICE: 0x4F0,09:39:02 INFO] [1] input #14 from src #0
[SERVICE: 0xD24,09:39:02 INFO] [1] input #14
[SERVICE: 0xD24,09:39:02 INFO] [MACHINE 1 INPUT #14] - (HDW) CheckDevNode
[SERVICE: 0xD24,09:39:02 INFO] * CItunesDevice::HandleHardwareInput()
[SERVICE: 0x4F0,09:42:41 INFO] [DevNodesChanged]
[SERVICE: 0x4F0,09:42:41 INFO] [1] input #15 from src #0
[SERVICE: 0x4F0,09:42:41 INFO] [DevNodesChanged]
[SERVICE: 0x4F0,09:42:41 INFO] [1] input #16 from src #0
[SERVICE: 0x4F0,09:42:41 INFO] [DevNodesChanged]
[SERVICE: 0x4F0,09:42:41 INFO] [1] input #17 from src #0
[SERVICE: 0x52C,09:42:41 INFO] [1] input #15
[SERVICE: 0x4EC,09:42:41 INFO] [1] input #16
[SERVICE: 0xD24,09:42:41 INFO] [1] input #17
[SERVICE: 0x52C,09:42:41 INFO] [MACHINE 1 INPUT #15] - (HDW) CheckDevNode
[SERVICE: 0x52C,09:42:49 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0x4EC,09:42:49 INFO] [MACHINE 1 INPUT #16] - (HDW) CheckDevNode
[SERVICE: 0x4EC,09:42:49 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xD24,09:42:49 INFO] [MACHINE 1 INPUT #17] - (HDW) CheckDevNode
[SERVICE: 0xD24,09:42:49 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0x4F0,09:42:51 INFO] [InterfaceArrival] \\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0x4F0,09:42:51 INFO] type 0x7 drive 0x1 partition 0x0
[SERVICE: 0x4F0,09:42:51 INFO] [1] set waiting to mount = 1
[SERVICE: 0x4F0,09:42:51 INFO] [1] Attempt to reassign from session 0 to session 0, DENIED!
[SERVICE: 0x4F0,09:42:51 INFO] [1] added device interface "\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}" to m_objDeviceNameMap
[SERVICE: 0x4F0,09:42:51 INFO] [1] added state machine 1 to m_objDeviceIdMap
[SERVICE: 0x4F0,09:42:51 INFO] [1] added device number 1 to m_objDeviceNumberMap
[SERVICE: 0x4F0,09:42:51 INFO] [1] added device interface "\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}" to m_vctDeviceInterfaces
[SERVICE: 0x4F0,09:42:51 INFO] [1] input #18 from src #0
[SERVICE: 0x52C,09:42:51 INFO] [1] input #18
[SERVICE: 0x4F0,09:42:51 INFO] [DevNodesChanged]
[SERVICE: 0x4F0,09:42:51 INFO] [1] input #19 from src #0
[SERVICE: 0x4EC,09:42:51 INFO] [1] input #19
[SERVICE: 0x4F0,09:42:51 INFO] [DevNodesChanged]
[SERVICE: 0x4F0,09:42:51 INFO] [1] input #20 from src #0
[SERVICE: 0xD24,09:42:51 INFO] [1] input #20
[SERVICE: 0x52C,09:42:51 INFO] [MACHINE 1 INPUT #18] - (HDW) Interface Arrival
[SERVICE: 0x52C,09:42:51 INFO] [1] progress state is 2, Waiting to mount = 1
[SERVICE: 0x52C,09:42:51 INFO] [1] progress is now 2
[SERVICE: 0x52C,09:42:51 INFO] [1] progress is now 2
[SERVICE: 0x52C,09:42:51 INFO] [MACHINE 1 TRANSITION] - {Unknown} ==> {Connected}
[SERVICE: 0x52C,09:42:51 INFO] [MACHINE 1 ACTIONS] - {Connected}
[SERVICE: 0x52C,09:42:51 INFO] [1] SCSI Inquiry attempt #0
[SERVICE: 0x52C,09:42:51 INFO] VendorId: Apple
[SERVICE: 0x52C,09:42:51 INFO] ProductId: iPod
[SERVICE: 0x52C,09:42:51 INFO] revision: 1.62
[SERVICE: 0x52C,09:42:51 INFO] vendor bytes:
[SERVICE: 0x52C,09:42:51 INFO] 02 01 00 00 00 00 00 00 00 05 00 13 12 00 00 00 00 00 00 00
[SERVICE: 0x52C,09:42:51 INFO] [1] firmware version: 1.62 (0x13E)
[SERVICE: 0x52C,09:42:51 INFO] [1] Power State: Not Powered
[SERVICE: 0x52C,09:42:51 INFO] [1] Checkpoint attempt #0
[SERVICE: 0x52C,09:42:51 ERROR] Did not find first letter of stage
[SERVICE: 0x52C,09:42:51 INFO] [1] serial number 000A270002BF5F21
[SERVICE: 0x52C,09:42:51 INFO] [1] *** CONNECTED - Sending event out, device session 0.
[SERVICE: 0x4EC,09:42:51 INFO] [MACHINE 1 INPUT #19] - (HDW) CheckDevNode
[SERVICE: 0x4EC,09:42:51 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xD24,09:42:51 INFO] [MACHINE 1 INPUT #20] - (HDW) CheckDevNode
[SERVICE: 0xD24,09:42:51 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0x4F0,09:42:53 INFO] [SIMULATED VOLUME ARRIVAL] generating volume mount for \\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0x4F0,09:42:53 INFO] [VolumeArrive] mask = 0x1C
[SERVICE: 0x4F0,09:42:53 INFO] looking up device # for \\.\E:
[SERVICE: 0x4F0,09:42:53 INFO] type 0x7 drive 0x1 partition 0x1
[SERVICE: 0x4F0,09:42:53 INFO] iTunes device #1 found with drive letter E, mask 0x10
[SERVICE: 0x4F0,09:42:53 INFO] [1] set waiting to mount = 0
[SERVICE: 0x4F0,09:42:53 INFO] [1] input #21 from src #0
[SERVICE: 0x52C,09:42:53 INFO] [1] input #21
[SERVICE: 0x4F0,09:42:53 INFO] looking up device # for \\.\D:
[SERVICE: 0x4F0,09:42:53 INFO] type 0x2 drive 0x0 partition 0xffffffff
[SERVICE: 0x4F0,09:42:53 INFO] [SIMULATED INTERFACE ARRIVAL] generating connect event for device 0
[SERVICE: 0x4F0,09:42:53 INFO] looking up device # for \\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0x4F0,09:42:53 INFO] type 0x7 drive 0x1 partition 0x0
[SERVICE: 0x52C,09:42:54 INFO] [MACHINE 1 INPUT #21] - (HDW) Volume Mount
[SERVICE: 0x52C,09:42:54 INFO] [MACHINE 1 TRANSITION] - {Connected} ==> {Mounted}
[SERVICE: 0x52C,09:42:54 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0x52C,09:42:54 INFO] [MACHINE 1 ACTIONS] - {Mounted}
[SERVICE: 0x52C,09:42:54 INFO] [1] progress state is 2, Waiting to mount = 0
[SERVICE: 0x52C,09:42:54 INFO] [1] progress state is 2, Waiting to mount = 0
[SERVICE: 0x52C,09:42:54 ERROR] Did not find first letter of stage
[SERVICE: 0x52C,09:43:02 INFO] [1] OS says filesystem is FAT32
[SERVICE: 0x52C,09:43:03 INFO] [1] ===== iPod Touch Wheel =====
[SERVICE: 0x52C,09:43:03 INFO] [1] progress state is 2, Waiting to mount = 0
[SERVICE: 0x52C,09:43:03 INFO] 9:43:3, year 2006, day of yr. 321, GMT offset 0 isDST 0
[SERVICE: 0x52C,09:43:03 INFO] [1] progress is now 0
[SERVICE: 0x52C,09:43:04 INFO] [1] *** MOUNTED - Sending event out, device session 0.
[SERVICE: 0x52C,09:43:04 INFO] [1] Auto-launch iTunes DISABLED
[SERVICE: 0x4F0,09:43:11 INFO] [VolumeArrive] mask = 0x10
[SERVICE: 0x4F0,09:43:11 INFO] looking up device # for \\.\E:
[SERVICE: 0x4F0,09:43:11 INFO] type 0x7 drive 0x1 partition 0x1
[SERVICE: 0x4F0,09:43:11 INFO] iTunes device #1 found with drive letter E, mask 0x10
[SERVICE: 0x4F0,09:43:11 INFO] [1] set waiting to mount = 0
[SERVICE: 0x4F0,09:43:11 INFO] [1] input #22 from src #0
[SERVICE: 0x4EC,09:43:11 INFO] [1] input #22
[SERVICE: 0x4EC,09:43:11 INFO] [MACHINE 1 INPUT #22] - (HDW) Volume Mount
[SERVICE: 0x4EC,09:43:11 INFO] ** CItunesDevice::HandleHardwareInput()
[SERVICE: 0x4F0,09:43:11 INFO] [DevNodesChanged]
[SERVICE: 0x4F0,09:43:11 INFO] [1] input #23 from src #0
[SERVICE: 0xD24,09:43:11 INFO] [1] input #23
[SERVICE: 0xD24,09:43:12 INFO] [MACHINE 1 INPUT #23] - (HDW) CheckDevNode
[SERVICE: 0xD24,09:43:12 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple&prod_ipod&rev1.62#000000bf5f21&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xF90,09:43:16 INFO] <0x4> Got Serial #
[SERVICE: 0x200,09:43:16 INFO] <0x4> GetFormatType() returned unknown format 0
[SERVICE: 0x200,09:43:16 INFO] [1] Progress state is 0, Waiting to disconnect = 0
[SERVICE: 0x200,09:43:16 INFO] Mounted
[SERVICE: 0x200,09:43:16 INFO] Device 1 is FAT32 and appears mounted, checking intermediate state...
[SERVICE: 0x200,09:43:16 INFO] Device 1 not in intermediate state. It appears to be truly mounted.
[SERVICE: 0xF90,09:43:16 INFO] Mounted
[SERVICE: 0xF90,09:43:16 INFO] [1] already mounted!
[SERVICE: 0xF90,09:43:16 INFO] [1] progress state is 0, Waiting to mount = 0
[SERVICE: 0x200,09:43:33 INFO] <0x4> GetFormatType() returned unknown format 0
[SERVICE: 0xD10,09:43:33 INFO] [1] Progress state is 0, Waiting to disconnect = 0
[SERVICE: 0xD10,09:43:33 INFO] Mounted
[SERVICE: 0xD10,09:43:33 INFO] Device 1 is FAT32 and appears mounted, checking intermediate state...
[SERVICE: 0xD10,09:43:33 INFO] Device 1 not in intermediate state. It appears to be truly mounted.
[SERVICE: 0xF90,09:43:33 INFO] <0x4> COM request for device 1 drive letter - E
[SERVICE: 0xD10,09:43:34 INFO] Mounted
[SERVICE: 0xD10,09:43:34 INFO] Device 0 is FAT32 and appears mounted, checking intermediate state...
[SERVICE: 0xD10,09:43:34 INFO] Device 0 not in intermediate state. It appears to be truly mounted.
[SERVICE: 0xF90,09:43:54 INFO] [1] Progress state is 0, Waiting to disconnect = 0
[SERVICE: 0xF90,09:43:54 INFO] Mounted
[SERVICE: 0xF90,09:43:54 INFO] Device 1 is FAT32 and appears mounted, checking intermediate state...
[SERVICE: 0xF90,09:43:54 INFO] Device 1 not in intermediate state. It appears to be truly mounted.
[SERVICE: 0x200,09:43:54 INFO] Mounted
[SERVICE: 0x200,09:43:54 INFO] [1] already mounted!
[SERVICE: 0x200,09:43:54 INFO] [1] progress state is 0, Waiting to mount = 0
[SERVICE: 0xD10,09:43:54 INFO] Mounted
[SERVICE: 0xD10,09:43:54 INFO] Device 0 is FAT32 and appears mounted, checking intermediate state...
[SERVICE: 0xD10,09:43:54 INFO] Device 0 not in intermediate state. It appears to be truly mounted.
[SERVICE: 0xF90,09:43:54 INFO] [1] Progress state is 0, Waiting to disconnect = 0
[SERVICE: 0xF90,09:43:54 INFO] Mounted
[SERVICE: 0xF90,09:43:54 INFO] Device 1 is FAT32 and appears mounted, checking intermediate state...
[SERVICE: 0xF90,09:43:54 INFO] Device 1 not in intermediate state. It appears to be truly mounted.

If anyone is interested I managed to solve this problem by reformatting the ipod as a mac ipod, with the help of friends system. This does get rid of the music but as I had it backed up wasn't a problem. I then plugged the mac Ipod back into a windows pc and reformatted it as a windows ipod which updated the firmware correctly and have'nt had a problem since.

Hard drive will not mount shows up in Disk Utility

I have an external drive with a bootable OS X 10.6.8. I was in a transition between building up a SSD swapped drive. The SSD is installed in the CPU box but I have my old installation running from an external.
I have several external hard drives. They are all Firewire. Some have USB 3.0 and or eSATA options but my MacMini only talks to Firewire and USB 2.0.
I understand that you daisy chain Firewire drives and turn them on and off in sequence as they fall from the CPU box/case.
Firewire is a power source. I run the external with the OS using an AC adapter but one Firewire drive is powered through Firewire.
I have had as many as 4 external drives running along with the internal drive without a glitch while I was reorganizing files.
Today I booted off the external drive. It was running fine. I turned on one Firewire drive (the one that runs on Firewire power). That drive stumbled. I recognized the sound when there is an interruption in power. This cause the external boot drive to stall. I had to force a reboot.
Now the external boot drive will not boot up. It does not mount but Disk Utility sees it. The drive itself is bright and clear in Disk Utility but the partition (single) is faded out. I can run Verify and repair in DU. DU says it doesn't see anything to repair. It will not mount on its own or when I click the Mount button in DU. It does not produce an icon on the Desktop (because it is not mounting).
I also have SpeedTools. But although it sees the drive I cannot do anything with it. None of its tools run more than a spli second before they fail.
This drive has USB 3.0 and I see everything through USB that I see through Firewire. Connecting the other way did not get around the problem.
Of course I will buy an AC adapter for every external drive and never run them using Firewire again but the horse is out of the barn.
I have the original installation disks and could run the Archive and Install option but it would require physically swapping drives with the internal. I'd like to avoid it if possible. It is a MacMini and tedious.
Any suggestions?

I took the problematic hard drive and installed it in my Mac Mini so I could attempt a Safe Boot and then Archive and Install if necessary.
Safe Mode didn't work. The drive produced the circle with a slash symbol.
I reset the PRAM which was part of a list of steps to work through I found created by Apple Support.
I was able to boot up to Verbose Mode and view the text of the boot process. I wrote it all down. I can answer questions about the content better than typing it all out exactly. It includes, "...journal magic is bad..." "...failed to open..." and ends with "...cannot mount root, errno = 19"
I attempted Archive and Install however when it went to show what target drives were available it was a blank box and all buttons were grayed out.
I rebooted and opened Disk Utility from the DVD. The drive appeared the same with the top main line bright and the partitioned volume faded. Still was unable to mount. I ran Verify and this time a red line of text appeared "Invalid content in Journal" and at the end I ran Repair. When running I could read line by line and at one point it showed "checking volume information" then the following line "Repairing volume" the following line "Rechecking volume" more line of checking then it ended with "The volume was repaired successfully."
It still would not mount. I ran Verify again and again said "Invalid content in Journal" and this time it stopped midway saying "The volume was found corrupt and needs to be repaired. Error: This disk needs to be repaired. Click Repair Disk."
I clicked Repair and it ended with The vol. was repaired successfully."
Still unable to mount I began repeating Repair over and over. Each time it found something to repair and ended with a success message. After several more Repairs I tried Verify and it stopped midway saying to Repair the disk.
Question: Does running Repair multiple times continue to correct bits and pieces little by little or is this a generic message and we should treat it as a problem Disk Utility cannot pinpoint and is just beating its head against the wall?
The step by step instructions I downloaded mentioned running Repair more than once but it did not say that running it 20 times would erode some problems and eventually lead to a fully repaired disk (if the problem was something DU could take care of in the first place). At this point I have run Repair about 20 times total with a series of 10 back to back skipping Verify. I keep seeing the lines about invalid content in a journal and that it repaired something successfully. Yet I still cannot mount the disk.

Bootcamp Partition Will Not Mount - Size Bootcamp Partition Will Not Mount - Also Size Discrepancies

I have bootcamp installed on an internal hard drive in my Mac Pro running 10.8.5. This HD had two partitions, one of which I had 200GB allocated for my Windows install. I reached a point where I was at nearly 100% capacity on that drive and needed more room. This is what I did:
Used Disk Utility to shrink the Mac OS Extended partition.
Erased free space on that partition.
Booted back into Windows and used MiniTool to extend the bootcamp partition to unallocated space.
MinoTool then performed a restart and finished it's job upon startup.
I am still able to boot into Windows and Mac just fine and I did create a backup of each OS before starting.
I have two issues now, however. Parallels no long recognized that Bootcamp partition. I decided to delete that VM and I had to uninstall Parallels completely anyways due to an upgrage isse to Parallels 9. After upgrading, Creating a VM from my BC was not an option. This is because the BC partition will not mount, it is greyed out in Disk Utitlity.
I tried installing Tuxera NTFS and the disk still cannot be mounted.
The other issue is that Disk Utility does not show the Bootcamp partition with the correct size. It still shows it with the original 200GB but does show that the Mac Partition was shrunk. In Windows, however, either using MiniTool or Windows Disk Managment, it shows the correct sizes for the partitions.
I'll attach a screenshot of DU.
I would like to be able to mount the drive successfully so that I can use the partition once again for Parallels.
This is the system.log display when attempting to mount the BOOTCAMP partition and when disabling Tuxera from the system preferences:
Nov 7 08:35:46 ***-mac-pro.local com.apple.SecurityServer[27]: Succeeded authorizing right 'system.volume.internal.mount' by client '/Applications/Utilities/Disk Utility.app' [973] for authorization created by '/Applications/Utilities/Disk Utility.app' [973] (100013,0)
Nov 7 08:35:46 ***-mac-pro.local com.apple.SecurityServer[27]: Succeeded authorizing right 'system.volume.internal.mount' by client '/usr/sbin/diskarbitrationd' [15] for authorization created by '/Applications/Utilities/Disk Utility.app' [973] (100002,0)
Nov 7 08:35:47 ***-mac-pro kernel[0]: NTFS driver 3.10 [Flags: R/W].
Nov 7 08:35:47 ***-mac-pro kernel[0]: NTFS volume name BOOTCAMP, version 3.1.
Nov 7 08:35:47 ***-mac-pro kernel[0]: NTFS-fs error (device /dev/disk3s3, pid 5414): ntfs_lookup_inode_by_name(): Directory index record with VCN 0x3 is corrupt. Corrupt inode 0x5. Run chkdsk.
Nov 7 08:35:47 ***-mac-pro kernel[0]: NTFS-fs error (device /dev/disk3s3, pid 5414): ntfs_windows_hibernation_status_check(): Failed to find inode number for hiberfil.sys.
Nov 7 08:35:47 ***-mac-pro kernel[0]: NTFS-fs warning (device /dev/disk3s3, pid 5414): ntfs_system_inodes_get(): Failed to determine if Windows is hibernated. Will not be able to remount read-write. Run chkdsk.
Nov 7 08:35:47 ***-mac-pro kernel[0]: NTFS-fs error (device /dev/disk3s3, pid 5414): ntfs_attr_find_in_attribute_list(): Base inode 0x9 contains corrupt attribute list attribute. Unmount and run chkdsk.
Nov 7 08:35:47 ***-mac-pro kernel[0]: NTFS-fs error (device /dev/disk3s3, pid 5414): ntfs_inode_read(): Failed to lookup data attribute.
Nov 7 08:35:47 ***-mac-pro kernel[0]: NTFS-fs error (device /dev/disk3s3, pid 5414): ntfs_inode_read(): Failed (error 5) for inode 0x9. Run chkdsk.
Nov 7 08:35:47 ***-mac-pro kernel[0]: NTFS-fs error (device /dev/disk3s3, pid 5414): ntfs_inode_attach(): Failed to load inode 0x9.
Nov 7 08:35:47 ***-mac-pro kernel[0]: NTFS-fs error (device /dev/disk3s3, pid 5414): ntfs_secure_load(): Failed to load $Secure.
Nov 7 08:35:47 ***-mac-pro kernel[0]: NTFS-fs error (device /dev/disk3s3, pid 5414): ntfs_mount(): Failed to load system files (error 5).
Nov 7 08:35:47 ***-mac-pro kernel[0]: NTFS-fs error (device /dev/disk3s3, pid 5414): ntfs_mount(): Mount failed (error 5).
Nov 7 08:35:48 ***-mac-pro.local com.apple.SecurityServer[27]: Succeeded authorizing right 'system.privilege.admin' by client '/Applications/System Preferences.app' [5297] for authorization created by '/Applications/System Preferences.app' [5297] (100012,0)
Thanks,
Josh

Josh,
I will defer to Christopher on correcting the GPT, but I agree it is incorrect. On a much simpler, single disk Macmini with Bootcamp...
sudo gpt -r -vv show /dev/rdisk0
gpt show: /dev/rdisk0: mediasize=500107862016; sectorsize=512; blocks=976773168
gpt show: /dev/rdisk0: Suspicious MBR at sector 0
gpt show: /dev/rdisk0: Pri GPT at sector 1
gpt show: /dev/rdisk0: Sec GPT at sector 976773167
      start       size index contents
          0          1         MBR
          1          1         Pri GPT header
          2         32         Pri GPT table
         34          6
         40     409600      1 GPT part - C12A7328-F81F-11D2-BA4B-00A0C93EC93B
     409640 725093952      2 GPT part - 48465300-0000-11AA-AA11-00306543ECAC
725503592    1269536      3 GPT part - 426F6F74-0000-11AA-AA11-00306543ECAC
726773128        632
726773760 249999360      4 GPT part - EBD0A0A2-B9E5-4433-87C0-68B6B72699C7
976773120         15
976773135         32         Sec GPT table
976773167          1         Sec GPT header
sudo fdisk /dev/rdisk0
Disk: /dev/rdisk0          geometry: 60801/255/63 [976773168 sectors]
Signature: 0xAA55
         Starting       Ending
#: id cyl hd sec - cyl hd sec [     start -       size]
1: EE 1023 254 63 - 1023 254 63 [         1 -     409639] <Unknown ID>
2: AF 1023 254 63 - 1023 254 63 [    409640 - 725093952] HFS+
3: AB 1023 254 63 - 1023 254 63 [ 725503592 -    1269536] Darwin Boot
*4: 07 1023 254 63 - 1023 254 63 [ 726773760 - 249999360] HPFS/QNX/AUX
diskutil list /dev/disk0
/dev/disk0
   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:      GUID_partition_scheme                        *500.1 GB   disk0
   1:                        EFI EFI                     209.7 MB   disk0s1
   2:                  Apple_HFS Macintosh HD            371.2 GB   disk0s2
   3:                 Apple_Boot Recovery HD             650.0 MB   disk0s3
   4:       Microsoft Basic Data BOOTCAMP                128.0 GB   disk0s4
PS: I see Christopher's response.

Hard drive will not mount with 10.4 but will mount with 10.3

I have a G4 powerbook running on 10.4.11. There is a western digital my book external drive hooked up to the USB port. I have two partitions on it. I tried to change the group settings to read write and got an error saying I did not have permission. Now the first partition will mount, but the second which I tried to change will not mount.
Disk utility sees the drive but it is grayed out. DiskWarrior sees the drive.
I dragged out my old G3 running 10.3.9 and plugged it in. Works great. The disk drive partition mounts and all of the files are there. What do I need to do to get 10.4.11 to mount the disk partition?
The external drive is a Western Digital My Book 250G divided equally into two partitions. The partitions are in Mac extended format.

I'm having pretty much the same problem... Have a WD 500 GB external attached via USB. I can't say for sure that the WD caused this (wasn't paying close enough attention), but I've noticed that my own MacBook HD is no longer mounted. I can't seem to find anyway to accomplish this either. I've booted from another volume to run Disk Utility (repair/verify). I rebooted with the MacBook startup drive and still, no HD. And NOW I can't see the bootable partition I made on the WD external. What?
I feel like the opposite of a nerd, cuz I'm just scratching my head at this point. Oh yeah, and running 10.4.11...

NEED HELP Xsan volume is not mounted (strange problem)

I ask the help in solving the volume mount problem. (advance I am sorry for my english)
All began with the fact that the MDC is rebooted and on the two LUNs were gone XSAN label. I relabeled these LUNs using commands:
cvlabel -c >label_list
then in the file label_list I corrected unknown disks on the label with a same names that were. Then I ran the cvlabel label_list command. Finally I got the correct label on all drives.
# cvlabel -l
/dev/rdisk14 [Raidix meta_i          3365] acfs-EFI "META_I"Sectors: 3906830002. Sector Size: 512. Maximum sectors: 3906975711.
/dev/rdisk15 [Raidix QSAN_I          3365] acfs-EFI "QSAN_I"Sectors: 7662714619. Sector Size: 4096. Maximum sectors: 7662714619.
/dev/rdisk16 [Raidix meta_ii         3365] acfs-EFI "META_II"Sectors: 3906830002. Sector Size: 512. Maximum sectors: 3906975711.
/dev/rdisk17 [Raidix 2k_I            3365] acfs-EFI "2K_I"Sectors: 31255934943. Sector Size: 512. Maximum sectors: 31255934943.
/dev/rdisk18 [Raidix 2k_II           3365] acfs-EFI "2K_II"Sectors: 31255934943. Sector Size: 512. Maximum sectors: 31255934943.
/dev/rdisk19 [Raidix QSAN_II         3365] acfs-EFI "QSAN_II"Sectors: 7662714619. Sector Size: 4096. Maximum sectors: 7662714619.
The volume [2K] starts successfully.
but not mounted on the MDC and client.
I ran a volume check:
sh-3.2# cvfsck -wv 2K
Checked Build disabled - default.
BUILD INFO:
#!@$ Revision 4.2.2 Build 7443 (480.8) Branch Head
#!@$ Built for Darwin 12.0
#!@$ Created on Mon Jul 29 17:01:44 PDT 2013
Created directory /tmp/cvfsck3929a for temporary files.
Attempting to acquire arbitration block... successful.
Creating MetadataAndJournal allocation check file.
Creating Video allocation check file.
Creating Data allocation check file.
Recovering Journal Log.
Super Block information.
FS Created On               : Wed Oct 2 23:59:20 2013
Inode Version               : '2.7' - 4.0 big inodes + NamedStreams (0x207)
File System Status          : Clean
Allocated Inodes            : 4022272
Free Inodes                 : 16815
FL Blocks                   : 79
Next Inode Chunk            : 0x51a67
Metadump Seqno              : 0
Restore Journal Seqno       : 0
Windows Security Indx Inode : 0x5
Windows Security Data Inode : 0x6
Quota Database Inode        : 0x7
ID Database Inode           : 0xa
Client Write Opens Inode    : 0x8
Stripe Group MetadataAndJournal             ( 0) 0x746ebf0 blocks.
Stripe Group Video                          ( 1) 0x746ffb60 blocks.
Stripe Group Data                           ( 2) 0xe45dfb60 blocks.
Inode block size is 1024
Building Inode Index Database 4022272 (100%).
   4022272 inodes found out of 4022272 expected.
Verifying NT Security Descriptors
Found 13 NT Security Descriptors: all are good
Verifying Free List Extents.
Scanning inodes 4022272 (100%).
Sorting extent list for MetadataAndJournal pass 1/1
Updating bitmap for MetadataAndJournal extents 21815 ( 0%).
Sorting extent list for Video pass 1/1
Updating bitmap for Video extents 3724510 ( 91%).
Sorting extent list for Data pass 1/1
Updating bitmap for Data extents 4057329 (100%).
Checking for dead inodes 4022272 (100%).
Checking directories 11136 (100%).
Scanning for orphaned inodes 4022272 (100%).
Verifying link & subdir counts 4022272 (100%).
Checking free list. 4022272 (100%).
Checking pending free list.
Checking Arbitration Control Block.
Checking MetadataAndJournal allocation bit maps (100%).
Checking Video allocation bit maps (100%).
Checking Data allocation bit maps (100%).
File system '2K'. Blocks-5784860352 free-3674376793 Inodes-4022272 free-16815.
File System Check completed successfully.
check not helping
sh-3.2# cvadmin
Xsan Administrator
Enter command(s)
For command help, enter "help" or "?".
List FSS
File System Services (* indicates service is in control of FS):
1>*2K[0]                located on big.local:64844 (pid 5217)
Select FSM "2K"
Created           :          Wed Oct 2 23:59:20 2013
Active Connections:          0
Fs Block Size     :          16K
Msg Buffer Size   :          4K
Disk Devices      :          5
Stripe Groups     :          3
Fs Blocks         :          5784860352 (86.20 TB)
Fs Blocks Free    :          3665561306 (54.62 TB) (63%)
Xsanadmin (2K) > show
Show stripe groups (File System "2K")
Stripe Group 0 [MetadataAndJournal] Status:Up,MetaData,Journal,Exclusive
Total Blocks:122088432 (1.82 TB) Reserved:0 (0.00 B) Free:121753961 (1.81 TB) (99%)
MultiPath Method:Rotate
    Primary Stripe [MetadataAndJournal] Read:Enabled Write:Enabled
Stripe Group 1 [Video] Status:Up
Total Blocks:1953495904 (29.11 TB) Reserved:270720 (4.13 GB) Free:129179 (1.97 GB) (0%)
MultiPath Method:Rotate
    Primary Stripe [Video] Read:Enabled Write:Enabled
Stripe Group 2 [Data] Status:Up
Total Blocks:3831364448 (57.09 TB) Reserved:270720 (4.13 GB) Free:3665432127 (54.62 TB) (95%)
MultiPath Method:Rotate
    Primary Stripe [Data] Read:Enabled Write:Enabled
I checked the availability of LUNs on MDC and client, there also all right.
But, unfortunately, the Volume is not mounted
xsanctl mount 2K
mount command failed: Unable to mount volume `2K' (error code: 5)
Please help me to figure out this situation, I will be grateful for any information.
Thanks

That looks like an I/O error. You may have an issue with one or more of the data LUNs. Check the system log for errors.

External USB drives will not mount under Mountain Lion

Since upgrading to Mountain Lion, two external USB2 drives that I have will not mount and cannot be viewed in the Finder. The same occurs on a 2012 MacBook Air, a 2009 iMac 27 and a 2010 MacMini, all running OS X Mountain Lion version 10.8.2.
Both drives are Samsung Story external USB drives (one is 1.5 GB and the other is 2 GB) and both have been formatted using Mac Disk Utility with a single Mac OS Extended (Journaled) partition, one using Snow Leopard and the other with Lion.
Both still mount correctly on a friends MacBook Pro that is still running Snow Leopard, and I had no problem with the same drives under Lion. Interestingly both can also be connected to Time Capsule USB port and show up correctly.
Both drives mount correctly under Windows 7 on BootCamp partitions that I have on both the 2012 MacBook Air, a 2009 iMac 27. These BootCamp partitions have Paragon HFS+ installed so I can read Mac formated drives.
Both drives show up in Disk Utility, but when attempt to mount the drives I get the message "The disk could not be mounted. Try running First Aid on the disk and retry mounting." I can run Repair in First Aid on the disk and get the message that the volume appears OK, but again have the same problem when I attempt to mount the disk.
I have also tried using Disk Utility 3,2, but still cannot mount the drives, though the program indicates there is no problem with the drives.
I have other portable USB including a Samsung portable USB2 drive, and two external USB3 drives, and I don't have problems with them.
There is clearly a problem with Mountain Lion with accessing (mounting) these Samsung Story USB drives, and the problem appears to be with Mountain Lion itself as the problem did not occur on the same Macs with Lion and does not occur with Bootcamp partitions on the machines.
I have a lot of time searching forums, but I have not found anyone with an identical problem.
I sure hope someone can help or that Apple come up with a fix for this issue which has only developed since the update to Mountain Lion.

bj10au wrote:
Since upgrading to Mountain Lion, two external USB2 drives that I have will not mount and cannot be viewed in the Finder. The same occurs on a 2012 MacBook Air, a 2009 iMac 27 and a 2010 MacMini, all running OS X Mountain Lion version 10.8.2.
Both drives are Samsung Story external USB drives (one is 1.5 GB and the other is 2 GB) and both have been formatted using Mac Disk Utility with a single Mac OS Extended (Journaled) partition, one using Snow Leopard and the other with Lion.
Both still mount correctly on a friends MacBook Pro that is still running Snow Leopard, and I had no problem with the same drives under Lion. Interestingly both can also be connected to Time Capsule USB port and show up correctly.
Both drives mount correctly under Windows 7 on BootCamp partitions that I have on both the 2012 MacBook Air, a 2009 iMac 27. These BootCamp partitions have Paragon HFS+ installed so I can read Mac formated drives.
Both drives show up in Disk Utility, but when attempt to mount the drives I get the message "The disk could not be mounted. Try running First Aid on the disk and retry mounting." I can run Repair in First Aid on the disk and get the message that the volume appears OK, but again have the same problem when I attempt to mount the disk.
I have also tried using Disk Utility 3,2, but still cannot mount the drives, though the program indicates there is no problem with the drives.
I have other portable USB including a Samsung portable USB2 drive, and two external USB3 drives, and I don't have problems with them.
There is clearly a problem with Mountain Lion with accessing (mounting) these Samsung Story USB drives, and the problem appears to be with Mountain Lion itself as the problem did not occur on the same Macs with Lion and does not occur with Bootcamp partitions on the machines.
I have a lot of time searching forums, but I have not found anyone with an identical problem.
I sure hope someone can help or that Apple come up with a fix for this issue which has only developed since the update to Mountain Lion.
You can start here
http://support.seagate.com/kbimg/flash/213059/213059_EN.HTML
Pete

Client will not mount SAN after upgrade to 10.4.8 Server

Living life on the bleeding edge, I loaded the 10.4.8 Server upgrade onto my G4 Xserve which is the MDC for my single Xraid SAN. The SAN started without a hitch, however, the volume would not mount on the client side. The MDC shows up in the client list and the mount buttons are active, but the SAN will not mount. The system log yields the following error:
Can not mount filesystem, cvfs error 'Invalid argument' (0xb) while initializing local portmapper
I checked the obvioius: /volume is clear of old links, running cvfsck showed no problems, and cvadmin stat looks ok and who shows the MDC as FSM and ADM.
Has anybody else run into this? Any observations would be welcomed!
Thanks,
babcom

As indicated on the tag line, Xsan 1.4. Upgrade from OS 10.4.7. SAN created using version 1.4. SAN mounted just fine under 10.4.7. In an attempt to isolate the problem, I tried mounting the SAN from the command line:
mount -t acfs iplVol1.cfg /Volumes
only to received the same invalid argument error. I suspect that a parameter name has been changed/deleted/munged when parsing the volume's cfg file. Since Apple did NOT reference the invalid string token in the error message, I can not be sure. I am just now getting back to work the issue.
Regards,
babcom

Ext HD will not mount

My lacie HD - forwire 200 gig will not mount. It shows up in disk utilities but not on the desktop. In the info section of disk utility, the smart status is not verified. It seemed to go wacky after the last security update.

Lacie offers this advise in their FAQs. Put in FireWire drive and Mac OS for the search fields.
1) Try a different cable.
2) Repair the Permissions. Open the Disk Utilities and click on the First Aid Tab. Highlight your 'boot volume' on the left side of the window and click on 'Repair Permissions'. (Don't bother verifying first. It takes as long as repair and something always needs repairing).
3) Shut down, power off and disconnect all devices. Unplug the computers power cable (or remove the battery if a laptop). Wait about 15 minutes. Plug everything back in and boot up. This may reset the bus.

External Drives will not mount

Hi guys ... this is my first post in these forums, so sorry if it is in the wrong category.
I have a Mac Pro, purchased in Feb this year. I have an iOmega Ultramax firewire drive, that is partitioned into four disks.
I have had time machine running well, and it backs everything up onto a second iOmega drive I have.
Yesterday, before I left for work, I saw TM was sbusy backing up. The finder was not responding but I just left it, as didnt have time to loko into it before leaving.
When I cam home last night, I saw it was still not responding, and TM was still trying to backup. All other apps were functioning fine.
I tried to force quit Finder and TM, but it did not work. I then shut down the Mac manually, and rebooted.
The problem has now arisen, where the partitioned drives will not mount at all. The TM backup drive is fine, and I can browse TM fine with it - so good to know all my data is backed up.
I looked at the logs in console, and see the messages saying that the drive cannot mount as it is dirty?
What I have tried as troubleshooting steps:
•Disk Utility to try and mount the drives, but they are not showing up
•Connecting the drive to my Mac Mini - still nothing.
•DiskWarrior - nothing. Only my TM backup drive and Mac HD show up.
•Running FSCK from Terminal. I can see the drives in /dev, but keep getting "Bad Super block" errors. When I try looking for another Super Block, it says nothing found, and would I like to run it manually? The same happens when run in single user mode.
•Unplugging the Mac and the drives from the Mac, waiting 5 mins, resetting the NVRAM and PRAM (booting up holding CMDPR and waiting for the second chime, shutting down, plugging in and turing n drives, rebooting ... nothing!
It seems as though I have exhausted all possible options.
I now accept that the drive is unrecoverable, and am relieved that the TM backups are OK. I am thus happy to format the drive and repartition it, then restore everything from TM. Will be a fairly big job, but at least the data is backed up.
The only problem I have, is I cannot even mount the drives to format them!
Is there any safe way of doing this over the command line. Or even better, has anybody gt any other advice as to options I can try?
I hope I have been thorough enough in my explanation here.
Thanks in advance,
Dave

The only problem I have, is I cannot even mount the drives to format them!
I have a feeling that the partition map is bad. Does the drive itself report to DU? If the drive does show up, you can select that, and click the Repair Disk button under the First Aid tab. If that doesn't fix it, with the drive selected, click the partition tab and re-partition the drive. After that, I would erase the newly created volumes with 1-pass/zero out option selected and restore the data that was on the external from TM.
If none of this works or if the drive itself (not the volumes) doesn't show up in DU, you either have a bad drive or bad controller in the external case. How old is the Ultramax? Just wondering if it might still be under manufacturer's warranty. I would check to see if you are still eligible from the manufacturer's warranty and get the whole external unit replaced. If you are out of warranty, I think it likely that you need to replace that external with a new one. I've had a drive go bad in an external case (this one I could still mount but the heads would 'freeze') and the controller on another external go bad (this one, the drive would not report to DU so I took the drive out of the enclosure, stuck the drive in another case and there was no problem with the drive.)

External firewire disk partition will not mount

I have two external hard drives connected by a firewire to my 2002 G4 iMac running OSX 10.3.9. One is a 160GB and the second a 360GB drive.
I was out of the room when the area experienced a minor power drop in voltage and when I came back the iMac had the message to shut down and restart. When I restarted everything appeared normal until I realised that one partition did not mount on the 360GB drive. I ran Disk Utility to check the disk and it found some issues (I failed to write them down..) but Disk Utility appeared to fix them.
The disk has 2 partitions and only one of the two partitions will not mount (the second partition works fine!). Disk Utility says that both partitions check OK.
I have rebooted several times. I have removed all other external attachments and rebooted but still the partition will not mount.
I cannot see the partition in Finder. The second partition on the disk is available to see and use in Finder.
I have selected the partition in Disk Utility (grayed out) and tried the "mount" button but nothing happens. For some 18 months up until now the drive has worked fine although I did notice a couple of times it took a while for the drive to open up in Finder and other applications. I use that particular partition daily, it has approx 100GB used of the 150GB total space.
When I ran Disk Utility it comes up with a variation in the results compared with the partition that has mounted OK. The result of running "Verify Disk" is listed below. The only diffeerence between the two partitions is the first line of each volume. Does the ",0" following "Checking HFS Plus volume." for the first partition called "Genesys1" indicate anything?
DISK UTILITY REPORT
Verifying volume “Genesys1”
Mounting Disk(S,"Checking HFS Plus volume.",0)
Checking Extents Overflow file.
Checking Catalog file.
Checking Catalog hierarchy.
Checking volume bitmap.
Checking volume information.
The volume Genesys1 appears to be OK.
Verifying volume “Genesys2”
Checking HFS Plus volume.
Checking Extents Overflow file.
Checking Catalog file.
Checking Catalog hierarchy.
Checking volume bitmap.
Checking volume information.
The volume Genesys2 appears to be OK.
2 volumes checked
2 HFS volumes verified
Any help would be appreciated.
Regards

Hello! Power failures are murder on disk drive directories as you have found out. Your best shot is to get DISKWARRIOR. It is the "gold standard" for these types of problems and can usually resolve the issue when Disk Utility cannot. As with any utility there are times when even it cannot fix things but it's the best there is at resolving such issues. Tom

Volume will NOT mount

Similar Messages

Maybe you are looking for