Volumes disappeared from DFS replication
Hi all,
Recently I set up DFS replication on Windows 2012 Std Server. Few days ago I tried to connect the 3rd server to this replication and found out that all volumes except C:\ drive are disappeared from DFS replication on the main server, so it can't do initial
replication.
When I go to DFS snap-in and create Diagnostic report for the replication - it shows me available volumes on every server - C:\ drive only for the main one and all volumes for other servers. Shares on the main server are up and running without any problems.
So the question is how to add the volumes back to DFS replication, any ideas?
Kind regards,
Artem.
Hi,
It seems that DFS replication can't sync between the main server and the second server. I suggest you recreate the replication group to resolve the issue. If there is any error message in the diagnostic report or event log? If so, please provide the error message
to troubleshoot the issue.
Please also refer to the thread below to see if it helps:
DFSR Replication Broken
http://social.technet.microsoft.com/Forums/windowsserver/en-US/b73aea9e-3a0e-4139-b02d-d3f205e0ab19/dfsr-replication-broken?forum=winserverfiles
Regards,
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.
Similar Messages
-
Cannot boot. volume disappeared from boot option after Disk Utility (GUI) repair
I have a 13-inch MBP with the latest OS X version.
Problem
Yesterday, I went to the Recovery Mode and performed Repair on my boot volume. I was not having a problem, but I just wanted to verify and repair as a regular maintenance. The Disk Utility said some kind of error (I cannot remember, but something about EFI?), and I cannot start my computer since then (question mark folder icon when I try to boot).
I have tried the following
I tried to recover the drive by going into the Recovery Mode, but when I press Option key for boot options, I just have an empty grey screen have no option(not even the recovery volume). I have also tried to enter into the Single User Mode, but it goes straight back to the question mark folder icon. Just in case, I performed PRAM and SMC reset, but still no dice.
Next, I tried to boot with Command+R pressed, and the computer went into Internet Recovery Mode, which works fine. Then, I went to the Disk Utility, and my SSD is on the list with the volume that has OS X(only volume on the entire disk except recovery volume, etc). I use FileVault2, and I can unlock the volume and mount it without any problem. When I do Verify Disk, it says that the volume appears to be OK. Also, performed fsck using Recovery Mode's Terminal, and it still says that "The volume Macintosh HD appears to be OK," the exact same message that I got from GUI disk utility. I also tried to unlock and set the volume as a start-up disk, but I still get the question mark folder icon.
If you need further details, please let me know! Please save me!Hello jukim,
Thanks for using Apple Support Communities.
Great troubleshooting done so far. Since you're still booting to the flashing question mark, even after repairing the disk, the next step would be to reinstall OS X.
A flashing question mark or globe appears when you start your Mac
https://support.apple.com/kb/TS1440
OS X Mavericks: Reinstall OS X
http://support.apple.com/kb/PH13871
Take care,
Alex H. -
The volume control has disappeared from the music app on my iPhone and i can't play any music how do i fix this?
Try a reset: Simultaneously hold down the Home and On buttons until the device shuts down. Ignore the off slider if it appears. Once shut down is complete, if it doesn't restart on it own, turn the device back on using the On button. In some cases it also helps to double click the Home button and close all apps from the tray BEFORE doing the reset.
-
Hi,
i am facing the problem SVSVOL folder replication, i also checked dcdiag and result is DFSRevent fail .
in event log i found the event Error:
The DFS Replication service stopped replication on the folder with the following local path: C:\Windows\SYSVOL\domain. This server has been disconnected from other partners for 173 days, which is longer than the time allowed by the MaxOfflineTimeInDays parameter
(61). DFS Replication considers the data in this folder to be stale, and this server will not replicate the folder until this error is corrected.
To resume replication of this folder, use the DFS Management snap-in to remove this server from the replication group, and then add it back to the group. This causes the server to perform an initial synchronization task, which replaces the stale data with fresh
data from other members of the replication group.
Additional Information:
Error: 9061 (The replicated folder has been offline for too long.)
Replicated Folder Name: SYSVOL Share
Replicated Folder ID: 427F62C0-0316-4DEA-B7FA-06A7D6C06A4F
Replication Group Name: Domain System Volume
Replication Group ID: CBED9B54-58D5-4081-ABD0-0C9D4EBA6027
Member ID: 67C302ED-F82A-4FC1-9A2C-62DBCC6BCA2A
please suggest me the solution..> disconnected from other partners for 173 days, which is longer than the
> please suggest me the solution..
Increase the MaxOfflineTimeInDays. Try google or bing :)
Martin
Mal ein
GUTES Buch über GPOs lesen?
NO THEY ARE NOT EVIL, if you know what you are doing:
Good or bad GPOs?
And if IT bothers me - coke bottle design refreshment :)) -
DFSR Event 5014 - DFS Replication service is stopping communication
Hi,
I seem to be having issues with the DFSR warnings in the event log. I receive the below warning every 5 minutes:
"The DFS Replication service is stopping communication with partner 'Servername' for replication group Domain System Volume due to an error. The service will retry the connection periodically.
Additional Information:
Error: 1726 (the remote procedure call failed.)"
The errors are immediately followed by an information entry (5004) stating that a connection was successfully established but then the warning repeats after 5 minutes again. Replication does actually seem to be working fine and the SYSVOL shares on both
domain controllers are identical.
I have run diagnostic reports from the DFS Management snapin and the only error reported is that
"The DFS Replication service is restarting frequently".
I have disabled TCP Offloading on the server as per other suggestions which doesn;t seem to have made a difference.
For reference, the domain controllers are in separate sites connected via site-to-site VPN. The AD sites are configured with the correct subnets and the WAN/VPN connection seems stable as I am getting consistent 87ms ping responses.
Any assistance would be greatly appreciated.
Thanks,
Charlie.Although I haven't specifically run into this, doing a Bing search I have seen a common theme that if there is a firewall between the two it drops the connection after a set period of inactivity. You might want to investigate that possibility.
http://faultbucket.ca/2011/02/dfsr-event-5014-the-remote-procedure-call-failed/
http://social.technet.microsoft.com/Forums/windowsserver/en-US/68c4f402-6c77-4388-9701-51a4fc112964/error-1726-the-remote-procedure-call-failed-every-7-minutes-dfsr-backlogs?forum=winserverDS
Paul Bergson
MVP - Directory Services
MCITP: Enterprise Administrator
MCTS, MCT, MCSE, MCSA, Security+, BS CSci
2008, Vista, 2003, 2000 (Early Achiever), NT4
Twitter @pbbergs
http://blogs.dirteam.com/blogs/paulbergson
Please no e-mails, any questions should be posted in the NewsGroup. This posting is provided "AS IS" with no warranties, and confers no rights. -
DFS replication stopped working and cannot be debugged because WMI repository cannot be accessed
Hello,
two days ago our DFS replication suddendly stopped working sometime around midnight local time. At least this is what our second domain controller is reporting. Event log is flooded with event id 5002 from DFSR. It is unclear what caused this sudden problem
and even worse, how to solve it. First thing I tried was to perform propagation tests. According to propagation report none of them was successful. Creating an integrity report brought me to another problem: It fails with two errors. First it is unable to
connect to the other DC. Second it is unable to access local WMI repository. This is true for both machines.
First I tried to find information on possible problems with WMI. WMIdiag provided a lot of information. However, opinions I found on the net largely disagree whether output from WMIdiag is useful or not. Yet I tried to re-compile .mof files and rebuild the
repository. So far, nothing changed. This is my output from WMIdiag:
34309 13:02:46 (0) ** WMIDiag v2.1 started on Donnerstag, 22. Mai 2014 at 12:49.
34310 13:02:46 (0) **
34311 13:02:46 (0) ** Copyright (c) Microsoft Corporation. All rights reserved - July 2007.
34312 13:02:46 (0) **
34313 13:02:46 (0) ** This script is not supported under any Microsoft standard support program or service.
34314 13:02:46 (0) ** The script is provided AS IS without warranty of any kind. Microsoft further disclaims all
34315 13:02:46 (0) ** implied warranties including, without limitation, any implied warranties of merchantability
34316 13:02:46 (0) ** or of fitness for a particular purpose. The entire risk arising out of the use or performance
34317 13:02:46 (0) ** of the scripts and documentation remains with you. In no event shall Microsoft, its authors,
34318 13:02:46 (0) ** or anyone else involved in the creation, production, or delivery of the script be liable for
34319 13:02:46 (0) ** any damages whatsoever (including, without limitation, damages for loss of business profits,
34320 13:02:46 (0) ** business interruption, loss of business information, or other pecuniary loss) arising out of
34321 13:02:46 (0) ** the use of or inability to use the script or documentation, even if Microsoft has been advised
34322 13:02:46 (0) ** of the possibility of such damages.
34323 13:02:46 (0) **
34324 13:02:46 (0) **
34325 13:02:46 (0) ** ----------------------------------------------------------------------------------------------------------------------------------
34326 13:02:46 (0) ** ----------------------------------------------------- WMI REPORT: BEGIN ----------------------------------------------------------
34327 13:02:46 (0) ** ----------------------------------------------------------------------------------------------------------------------------------
34328 13:02:46 (0) **
34329 13:02:46 (0) ** ----------------------------------------------------------------------------------------------------------------------------------
34330 13:02:46 (0) ** Windows Server 2008 R2 - Service pack 1 - 64-bit (7601) - User 'COM\ABCDEF' on computer 'DC2'.
34331 13:02:46 (0) ** ----------------------------------------------------------------------------------------------------------------------------------
34332 13:02:46 (0) ** INFO: Environment: .................................................................................................. 1 ITEM(S)!
34333 13:02:46 (0) ** INFO: => 1 possible incorrect shutdown(s) detected on:
34334 13:02:46 (0) ** - Shutdown on 01 April 2014 10:20:54 (GMT-0).
34335 13:02:46 (0) **
34336 13:02:46 (0) ** System drive: ....................................................................................................... C: (Datenträgernr. 0 Partitionsnr. 1).
34337 13:02:46 (0) ** Drive type: ......................................................................................................... SCSI (Adaptec Array SCSI Disk Device).
34338 13:02:46 (0) ** There are no missing WMI system files: .............................................................................. OK.
34339 13:02:46 (0) ** There are no missing WMI repository files: .......................................................................... OK.
34340 13:02:46 (0) ** WMI repository state: ............................................................................................... CONSISTENT.
34341 13:02:46 (0) ** AFTER running WMIDiag:
34342 13:02:46 (0) ** The WMI repository has a size of: ................................................................................... 26 MB.
34343 13:02:46 (0) ** - Disk free space on 'C:': .......................................................................................... 10665 MB.
34344 13:02:46 (0) ** - INDEX.BTR, 4276224 bytes, 22.05.2014 12:52:30
34345 13:02:46 (0) ** - MAPPING1.MAP, 67248 bytes, 22.05.2014 12:52:30
34346 13:02:46 (0) ** - MAPPING2.MAP, 67168 bytes, 22.05.2014 12:48:33
34347 13:02:46 (0) ** - OBJECTS.DATA, 23126016 bytes, 22.05.2014 12:52:30
34348 13:02:46 (0) ** ----------------------------------------------------------------------------------------------------------------------------------
34349 13:02:46 (0) ** INFO: Windows Firewall status: ...................................................................................... ENABLED.
34350 13:02:46 (0) ** Windows Firewall Profile: ........................................................................................... DOMAIN.
34351 13:02:46 (0) ** Inbound connections that do not match a rule BLOCKED: ............................................................... ENABLED.
34352 13:02:46 (0) ** => This will prevent any WMI remote connectivity to this computer except
34353 13:02:46 (0) ** if the following three inbound rules are ENABLED and non-BLOCKING:
34354 13:02:46 (0) ** - 'Windows Management Instrumentation (DCOM-In)'
34355 13:02:46 (0) ** - 'Windows Management Instrumentation (WMI-In)'
34356 13:02:46 (0) ** - 'Windows Management Instrumentation (ASync-In)'
34357 13:02:46 (0) ** Verify the reported status for each of these three inbound rules below.
34358 13:02:46 (0) **
34359 13:02:46 (0) ** Windows Firewall 'Windows Management Instrumentation (WMI)' group rule: ............................................. DISABLED.
34360 13:02:46 (0) ** => This will prevent any WMI remote connectivity to/from this machine.
34361 13:02:46 (0) ** - You can adjust the configuration by executing the following command:
34362 13:02:46 (0) ** i.e. 'NETSH.EXE ADVFIREWALL FIREWALL SET RULE GROUP="Windows Management Instrumentation (WMI)" NEW ENABLE=YES'
34363 13:02:46 (0) ** Note: With this command all inbound and outbound WMI rules are activated at once!
34364 13:02:46 (0) ** You can also enable each individual rule instead of activating the group rule.
34365 13:02:46 (0) **
34366 13:02:46 (0) ** ----------------------------------------------------------------------------------------------------------------------------------
34367 13:02:46 (0) ** DCOM Status: ........................................................................................................ OK.
34368 13:02:46 (0) ** WMI registry setup: ................................................................................................. OK.
34369 13:02:46 (0) ** INFO: WMI service has dependents: ................................................................................... 1 SERVICE(S)!
34370 13:02:46 (0) ** - Internet Connection Sharing (ICS) (SHAREDACCESS, StartMode='Disabled')
34371 13:02:46 (0) ** => If the WMI service is stopped, the listed service(s) will have to be stopped as well.
34372 13:02:46 (0) ** Note: If the service is marked with (*), it means that the service/application uses WMI but
34373 13:02:46 (0) ** there is no hard dependency on WMI. However, if the WMI service is stopped,
34374 13:02:46 (0) ** this can prevent the service/application to work as expected.
34375 13:02:46 (0) **
34376 13:02:46 (0) ** RPCSS service: ...................................................................................................... OK (Already started).
34377 13:02:46 (0) ** WINMGMT service: .................................................................................................... OK (Already started).
34378 13:02:46 (0) ** ----------------------------------------------------------------------------------------------------------------------------------
34379 13:02:46 (0) ** WMI service DCOM setup: ............................................................................................. OK.
34380 13:02:46 (0) ** WMI components DCOM registrations: .................................................................................. OK.
34381 13:02:46 (0) ** WMI ProgID registrations: ........................................................................................... OK.
34382 13:02:46 (0) ** WMI provider DCOM registrations: .................................................................................... OK.
34383 13:02:46 (0) ** WMI provider CIM registrations: ..................................................................................... OK.
34384 13:02:46 (0) ** WMI provider CLSIDs: ................................................................................................ OK.
34385 13:02:46 (2) !! WARNING: Some WMI providers EXE/DLL file(s) are missing: ............................................................ 1 WARNING(S)!
34386 13:02:46 (0) ** - ROOT/MICROSOFTACTIVEDIRECTORY, ReplProv1, replprov.dll
34387 13:02:46 (0) ** => This will make any operations related to the WMI class supported by the provider(s) to fail.
34388 13:02:46 (0) ** This can be due to:
34389 13:02:46 (0) ** - the de-installation of the software.
34390 13:02:46 (0) ** - the deletion of some files.
34391 13:02:46 (0) ** => If the software has been de-installed intentionally, then this information must be
34392 13:02:46 (0) ** removed from the WMI repository. You can use the 'WMIC.EXE' command to remove
34393 13:02:46 (0) ** the provider registration data.
34394 13:02:46 (0) ** i.e. 'WMIC.EXE /NAMESPACE:\\ROOT\MICROSOFTACTIVEDIRECTORY path __Win32Provider Where Name='ReplProv1' DELETE'
34395 13:02:46 (0) ** => If not, you must restore a copy of the missing provider EXE/DLL file(s) as indicated by the path.
34396 13:02:46 (0) ** You can retrieve the missing file from:
34397 13:02:46 (0) ** - A backup.
34398 13:02:46 (0) ** - The Windows CD.
34399 13:02:46 (0) ** - Another Windows installation using the same version and service pack level of the examined system.
34400 13:02:46 (0) ** - The original CD or software package installing this WMI provider.
34401 13:02:46 (0) **
34402 13:02:46 (0) ** ----------------------------------------------------------------------------------------------------------------------------------
34403 13:02:46 (0) ** INFO: User Account Control (UAC): ................................................................................... DISABLED.
34404 13:02:46 (0) ** INFO: Local Account Filtering: ...................................................................................... ENABLED.
34405 13:02:46 (0) ** => WMI tasks remotely accessing WMI information on this computer and requiring Administrative
34406 13:02:46 (0) ** privileges MUST use a DOMAIN account part of the Local Administrators group of this computer
34407 13:02:46 (0) ** to ensure that administrative privileges are granted. If a Local User account is used for remote
34408 13:02:46 (0) ** accesses, it will be reduced to a plain user (filtered token), even if it is part of the Local Administrators group.
34409 13:02:46 (0) **
34410 13:02:46 (0) ** DCOM security for 'My Computer' (Access Permissions/Edit Limits): ................................................... MODIFIED.
34411 13:02:46 (1) !! ERROR: Default trustee 'NT AUTHORITY\ANONYMOUS LOGON' has been REMOVED!
34412 13:02:46 (0) ** - REMOVED ACE:
34413 13:02:46 (0) ** ACEType: &h0
34414 13:02:46 (0) ** ACCESS_ALLOWED_ACE_TYPE
34415 13:02:46 (0) ** ACEFlags: &h0
34416 13:02:46 (0) ** ACEMask: &h7
34417 13:02:46 (0) ** DCOM_RIGHT_EXECUTE
34418 13:02:46 (0) ** DCOM_RIGHT_ACCESS_LOCAL
34419 13:02:46 (0) ** DCOM_RIGHT_ACCESS_REMOTE
34420 13:02:46 (0) **
34421 13:02:46 (0) ** => The REMOVED ACE was part of the DEFAULT setup for the trustee.
34422 13:02:46 (0) ** Removing default security will cause some operations to fail!
34423 13:02:46 (0) ** It is possible to fix this issue by editing the security descriptor and adding the ACE.
34424 13:02:46 (0) ** For DCOM objects, this can be done with 'DCOMCNFG.EXE'.
34425 13:02:46 (0) **
34426 13:02:46 (0) ** DCOM security for 'My Computer' (Access Permissions/Edit Limits): ................................................... MODIFIED.
34427 13:02:46 (1) !! ERROR: Default trustee 'BUILTIN\PERFORMANCE LOG USERS' has been REMOVED!
34428 13:02:46 (0) ** - REMOVED ACE:
34429 13:02:46 (0) ** ACEType: &h0
34430 13:02:46 (0) ** ACCESS_ALLOWED_ACE_TYPE
34431 13:02:46 (0) ** ACEFlags: &h0
34432 13:02:46 (0) ** ACEMask: &h7
34433 13:02:46 (0) ** DCOM_RIGHT_EXECUTE
34434 13:02:46 (0) ** DCOM_RIGHT_ACCESS_LOCAL
34435 13:02:46 (0) ** DCOM_RIGHT_ACCESS_REMOTE
34436 13:02:46 (0) **
34437 13:02:46 (0) ** => The REMOVED ACE was part of the DEFAULT setup for the trustee.
34438 13:02:46 (0) ** Removing default security will cause some operations to fail!
34439 13:02:46 (0) ** It is possible to fix this issue by editing the security descriptor and adding the ACE.
34440 13:02:46 (0) ** For DCOM objects, this can be done with 'DCOMCNFG.EXE'.
34441 13:02:46 (0) **
34442 13:02:46 (0) ** DCOM security for 'My Computer' (Access Permissions/Edit Limits): ................................................... MODIFIED.
34443 13:02:46 (1) !! ERROR: Default trustee 'EVERYONE' has been REMOVED!
34444 13:02:46 (0) ** - REMOVED ACE:
34445 13:02:46 (0) ** ACEType: &h0
34446 13:02:46 (0) ** ACCESS_ALLOWED_ACE_TYPE
34447 13:02:46 (0) ** ACEFlags: &h0
34448 13:02:46 (0) ** ACEMask: &h7
34449 13:02:46 (0) ** DCOM_RIGHT_EXECUTE
34450 13:02:46 (0) ** DCOM_RIGHT_ACCESS_LOCAL
34451 13:02:46 (0) ** DCOM_RIGHT_ACCESS_REMOTE
34452 13:02:46 (0) **
34453 13:02:46 (0) ** => The REMOVED ACE was part of the DEFAULT setup for the trustee.
34454 13:02:46 (0) ** Removing default security will cause some operations to fail!
34455 13:02:46 (0) ** It is possible to fix this issue by editing the security descriptor and adding the ACE.
34456 13:02:46 (0) ** For DCOM objects, this can be done with 'DCOMCNFG.EXE'.
34457 13:02:46 (0) **
34458 13:02:46 (0) ** DCOM security for 'My Computer' (Launch & Activation Permissions/Edit Default): ..................................... MODIFIED.
34459 13:02:46 (1) !! ERROR: Default trustee 'BUILTIN\ADMINISTRATORS' has been REMOVED!
34460 13:02:46 (0) ** - REMOVED ACE:
34461 13:02:46 (0) ** ACEType: &h0
34462 13:02:46 (0) ** ACCESS_ALLOWED_ACE_TYPE
34463 13:02:46 (0) ** ACEFlags: &h0
34464 13:02:46 (0) ** ACEMask: &h1F
34465 13:02:46 (0) ** DCOM_RIGHT_EXECUTE
34466 13:02:46 (0) ** DCOM_RIGHT_LAUNCH_LOCAL
34467 13:02:46 (0) ** DCOM_RIGHT_LAUNCH_REMOTE
34468 13:02:46 (0) ** DCOM_RIGHT_ACTIVATE_LOCAL
34469 13:02:46 (0) ** DCOM_RIGHT_ACTIVATE_REMOTE
34470 13:02:46 (0) **
34471 13:02:46 (0) ** => The REMOVED ACE was part of the DEFAULT setup for the trustee.
34472 13:02:46 (0) ** Removing default security will cause some operations to fail!
34473 13:02:46 (0) ** It is possible to fix this issue by editing the security descriptor and adding the ACE.
34474 13:02:46 (0) ** For DCOM objects, this can be done with 'DCOMCNFG.EXE'.
34475 13:02:46 (0) **
34476 13:02:46 (0) ** DCOM security for 'My Computer' (Launch & Activation Permissions/Edit Default): ..................................... MODIFIED.
34477 13:02:46 (1) !! ERROR: Default trustee 'NT AUTHORITY\INTERACTIVE' has been REMOVED!
34478 13:02:46 (0) ** - REMOVED ACE:
34479 13:02:46 (0) ** ACEType: &h0
34480 13:02:46 (0) ** ACCESS_ALLOWED_ACE_TYPE
34481 13:02:46 (0) ** ACEFlags: &h0
34482 13:02:46 (0) ** ACEMask: &h1F
34483 13:02:46 (0) ** DCOM_RIGHT_EXECUTE
34484 13:02:46 (0) ** DCOM_RIGHT_LAUNCH_LOCAL
34485 13:02:46 (0) ** DCOM_RIGHT_LAUNCH_REMOTE
34486 13:02:46 (0) ** DCOM_RIGHT_ACTIVATE_LOCAL
34487 13:02:46 (0) ** DCOM_RIGHT_ACTIVATE_REMOTE
34488 13:02:46 (0) **
34489 13:02:46 (0) ** => The REMOVED ACE was part of the DEFAULT setup for the trustee.
34490 13:02:46 (0) ** Removing default security will cause some operations to fail!
34491 13:02:46 (0) ** It is possible to fix this issue by editing the security descriptor and adding the ACE.
34492 13:02:46 (0) ** For DCOM objects, this can be done with 'DCOMCNFG.EXE'.
34493 13:02:46 (0) **
34494 13:02:46 (0) ** DCOM security for 'My Computer' (Launch & Activation Permissions/Edit Default): ..................................... MODIFIED.
34495 13:02:46 (1) !! ERROR: Default trustee 'NT AUTHORITY\SYSTEM' has been REMOVED!
34496 13:02:46 (0) ** - REMOVED ACE:
34497 13:02:46 (0) ** ACEType: &h0
34498 13:02:46 (0) ** ACCESS_ALLOWED_ACE_TYPE
34499 13:02:46 (0) ** ACEFlags: &h0
34500 13:02:46 (0) ** ACEMask: &h1F
34501 13:02:46 (0) ** DCOM_RIGHT_EXECUTE
34502 13:02:46 (0) ** DCOM_RIGHT_LAUNCH_LOCAL
34503 13:02:46 (0) ** DCOM_RIGHT_LAUNCH_REMOTE
34504 13:02:46 (0) ** DCOM_RIGHT_ACTIVATE_LOCAL
34505 13:02:46 (0) ** DCOM_RIGHT_ACTIVATE_REMOTE
34506 13:02:46 (0) **
34507 13:02:46 (0) ** => The REMOVED ACE was part of the DEFAULT setup for the trustee.
34508 13:02:46 (0) ** Removing default security will cause some operations to fail!
34509 13:02:46 (0) ** It is possible to fix this issue by editing the security descriptor and adding the ACE.
34510 13:02:46 (0) ** For DCOM objects, this can be done with 'DCOMCNFG.EXE'.
34511 13:02:46 (0) **
34512 13:02:46 (0) ** DCOM security for 'My Computer' (Launch & Activation Permissions/Edit Limits): ...................................... MODIFIED.
34513 13:02:46 (1) !! ERROR: Default trustee 'BUILTIN\ADMINISTRATORS' has been REMOVED!
34514 13:02:46 (0) ** - REMOVED ACE:
34515 13:02:46 (0) ** ACEType: &h0
34516 13:02:46 (0) ** ACCESS_ALLOWED_ACE_TYPE
34517 13:02:46 (0) ** ACEFlags: &h0
34518 13:02:46 (0) ** ACEMask: &h1F
34519 13:02:46 (0) ** DCOM_RIGHT_EXECUTE
34520 13:02:46 (0) ** DCOM_RIGHT_LAUNCH_LOCAL
34521 13:02:46 (0) ** DCOM_RIGHT_LAUNCH_REMOTE
34522 13:02:46 (0) ** DCOM_RIGHT_ACTIVATE_LOCAL
34523 13:02:46 (0) ** DCOM_RIGHT_ACTIVATE_REMOTE
34524 13:02:46 (0) **
34525 13:02:46 (0) ** => The REMOVED ACE was part of the DEFAULT setup for the trustee.
34526 13:02:46 (0) ** Removing default security will cause some operations to fail!
34527 13:02:46 (0) ** It is possible to fix this issue by editing the security descriptor and adding the ACE.
34528 13:02:46 (0) ** For DCOM objects, this can be done with 'DCOMCNFG.EXE'.
34529 13:02:46 (0) **
34530 13:02:46 (0) ** DCOM security for 'My Computer' (Launch & Activation Permissions/Edit Limits): ...................................... MODIFIED.
34531 13:02:46 (1) !! ERROR: Default trustee 'BUILTIN\PERFORMANCE LOG USERS' has been REMOVED!
34532 13:02:46 (0) ** - REMOVED ACE:
34533 13:02:46 (0) ** ACEType: &h0
34534 13:02:46 (0) ** ACCESS_ALLOWED_ACE_TYPE
34535 13:02:46 (0) ** ACEFlags: &h0
34536 13:02:46 (0) ** ACEMask: &h1F
34537 13:02:46 (0) ** DCOM_RIGHT_EXECUTE
34538 13:02:46 (0) ** DCOM_RIGHT_LAUNCH_LOCAL
34539 13:02:46 (0) ** DCOM_RIGHT_LAUNCH_REMOTE
34540 13:02:46 (0) ** DCOM_RIGHT_ACTIVATE_LOCAL
34541 13:02:46 (0) ** DCOM_RIGHT_ACTIVATE_REMOTE
34542 13:02:46 (0) **
34543 13:02:46 (0) ** => The REMOVED ACE was part of the DEFAULT setup for the trustee.
34544 13:02:46 (0) ** Removing default security will cause some operations to fail!
34545 13:02:46 (0) ** It is possible to fix this issue by editing the security descriptor and adding the ACE.
34546 13:02:46 (0) ** For DCOM objects, this can be done with 'DCOMCNFG.EXE'.
34547 13:02:46 (0) **
34548 13:02:46 (0) ** DCOM security for 'My Computer' (Launch & Activation Permissions/Edit Limits): ...................................... MODIFIED.
34549 13:02:46 (1) !! ERROR: Default trustee 'EVERYONE' has been REMOVED!
34550 13:02:46 (0) ** - REMOVED ACE:
34551 13:02:46 (0) ** ACEType: &h0
34552 13:02:46 (0) ** ACCESS_ALLOWED_ACE_TYPE
34553 13:02:46 (0) ** ACEFlags: &h0
34554 13:02:46 (0) ** ACEMask: &hB
34555 13:02:46 (0) ** DCOM_RIGHT_EXECUTE
34556 13:02:46 (0) ** DCOM_RIGHT_LAUNCH_LOCAL
34557 13:02:46 (0) ** DCOM_RIGHT_ACTIVATE_LOCAL
34558 13:02:46 (0) **
34559 13:02:46 (0) ** => The REMOVED ACE was part of the DEFAULT setup for the trustee.
34560 13:02:46 (0) ** Removing default security will cause some operations to fail!
34561 13:02:46 (0) ** It is possible to fix this issue by editing the security descriptor and adding the ACE.
34562 13:02:46 (0) ** For DCOM objects, this can be done with 'DCOMCNFG.EXE'.
34563 13:02:46 (0) **
34564 13:02:46 (0) ** DCOM security for 'Microsoft WMI Provider Subsystem Host' (Launch & Activation Permissions): ........................ MODIFIED.
34565 13:02:46 (1) !! ERROR: Default trustee 'BUILTIN\ADMINISTRATORS' has been REMOVED!
34566 13:02:46 (0) ** - REMOVED ACE:
34567 13:02:46 (0) ** ACEType: &h0
34568 13:02:46 (0) ** ACCESS_ALLOWED_ACE_TYPE
34569 13:02:46 (0) ** ACEFlags: &h0
34570 13:02:46 (0) ** ACEMask: &h1F
34571 13:02:46 (0) ** DCOM_RIGHT_EXECUTE
34572 13:02:46 (0) ** DCOM_RIGHT_LAUNCH_LOCAL
34573 13:02:46 (0) ** DCOM_RIGHT_LAUNCH_REMOTE
34574 13:02:46 (0) ** DCOM_RIGHT_ACTIVATE_LOCAL
34575 13:02:46 (0) ** DCOM_RIGHT_ACTIVATE_REMOTE
34576 13:02:46 (0) **
34577 13:02:46 (0) ** => The REMOVED ACE was part of the DEFAULT setup for the trustee.
34578 13:02:46 (0) ** Removing default security will cause some operations to fail!
34579 13:02:46 (0) ** It is possible to fix this issue by editing the security descriptor and adding the ACE.
34580 13:02:46 (0) ** For DCOM objects, this can be done with 'DCOMCNFG.EXE'.
34581 13:02:46 (0) **
34582 13:02:46 (0) ** DCOM security for 'Microsoft WMI Provider Subsystem Host' (Launch & Activation Permissions): ........................ MODIFIED.
34583 13:02:46 (1) !! ERROR: Default trustee 'NT AUTHORITY\INTERACTIVE' has been REMOVED!
34584 13:02:46 (0) ** - REMOVED ACE:
34585 13:02:46 (0) ** ACEType: &h0
34586 13:02:46 (0) ** ACCESS_ALLOWED_ACE_TYPE
34587 13:02:46 (0) ** ACEFlags: &h0
34588 13:02:46 (0) ** ACEMask: &h1F
34589 13:02:46 (0) ** DCOM_RIGHT_EXECUTE
34590 13:02:46 (0) ** DCOM_RIGHT_LAUNCH_LOCAL
34591 13:02:46 (0) ** DCOM_RIGHT_LAUNCH_REMOTE
34592 13:02:46 (0) ** DCOM_RIGHT_ACTIVATE_LOCAL
34593 13:02:46 (0) ** DCOM_RIGHT_ACTIVATE_REMOTE
34594 13:02:46 (0) **
34595 13:02:46 (0) ** => The REMOVED ACE was part of the DEFAULT setup for the trustee.
34596 13:02:46 (0) ** Removing default security will cause some operations to fail!
34597 13:02:46 (0) ** It is possible to fix this issue by editing the security descriptor and adding the ACE.
34598 13:02:46 (0) ** For DCOM objects, this can be done with 'DCOMCNFG.EXE'.
34599 13:02:46 (0) **
34600 13:02:46 (0) ** DCOM security for 'Microsoft WMI Provider Subsystem Host' (Launch & Activation Permissions): ........................ MODIFIED.
34601 13:02:46 (1) !! ERROR: Default trustee 'NT AUTHORITY\SYSTEM' has been REMOVED!
34602 13:02:46 (0) ** - REMOVED ACE:
34603 13:02:46 (0) ** ACEType: &h0
34604 13:02:46 (0) ** ACCESS_ALLOWED_ACE_TYPE
34605 13:02:46 (0) ** ACEFlags: &h0
34606 13:02:46 (0) ** ACEMask: &h1F
34607 13:02:46 (0) ** DCOM_RIGHT_EXECUTE
34608 13:02:46 (0) ** DCOM_RIGHT_LAUNCH_LOCAL
34609 13:02:46 (0) ** DCOM_RIGHT_LAUNCH_REMOTE
34610 13:02:46 (0) ** DCOM_RIGHT_ACTIVATE_LOCAL
34611 13:02:46 (0) ** DCOM_RIGHT_ACTIVATE_REMOTE
34612 13:02:46 (0) **
34613 13:02:46 (0) ** => The REMOVED ACE was part of the DEFAULT setup for the trustee.
34614 13:02:46 (0) ** Removing default security will cause some operations to fail!
34615 13:02:46 (0) ** It is possible to fix this issue by editing the security descriptor and adding the ACE.
34616 13:02:46 (0) ** For DCOM objects, this can be done with 'DCOMCNFG.EXE'.
34617 13:02:46 (0) **
34618 13:02:46 (0) ** DCOM security for 'Microsoft WMI Provider Subsystem Host' (Launch & Activation Permissions): ........................ MODIFIED.
34619 13:02:46 (1) !! ERROR: Default trustee 'NT AUTHORITY\NETWORK SERVICE' has been REMOVED!
34620 13:02:46 (0) ** - REMOVED ACE:
34621 13:02:46 (0) ** ACEType: &h0
34622 13:02:46 (0) ** ACCESS_ALLOWED_ACE_TYPE
34623 13:02:46 (0) ** ACEFlags: &h0
34624 13:02:46 (0) ** ACEMask: &h1F
34625 13:02:46 (0) ** DCOM_RIGHT_EXECUTE
34626 13:02:46 (0) ** DCOM_RIGHT_LAUNCH_LOCAL
34627 13:02:46 (0) ** DCOM_RIGHT_LAUNCH_REMOTE
34628 13:02:46 (0) ** DCOM_RIGHT_ACTIVATE_LOCAL
34629 13:02:46 (0) ** DCOM_RIGHT_ACTIVATE_REMOTE
34630 13:02:46 (0) **
34631 13:02:46 (0) ** => The REMOVED ACE was part of the DEFAULT setup for the trustee.
34632 13:02:46 (0) ** Removing default security will cause some operations to fail!
34633 13:02:46 (0) ** It is possible to fix this issue by editing the security descriptor and adding the ACE.
34634 13:02:46 (0) ** For DCOM objects, this can be done with 'DCOMCNFG.EXE'.
34635 13:02:46 (0) **
34636 13:02:46 (0) ** DCOM security for 'Microsoft WMI Provider Subsystem Host' (Launch & Activation Permissions): ........................ MODIFIED.
34637 13:02:46 (1) !! ERROR: Default trustee 'NT AUTHORITY\LOCAL SERVICE' has been REMOVED!
34638 13:02:46 (0) ** - REMOVED ACE:
34639 13:02:46 (0) ** ACEType: &h0
34640 13:02:46 (0) ** ACCESS_ALLOWED_ACE_TYPE
34641 13:02:46 (0) ** ACEFlags: &h0
34642 13:02:46 (0) ** ACEMask: &h1F
34643 13:02:46 (0) ** DCOM_RIGHT_EXECUTE
34644 13:02:46 (0) ** DCOM_RIGHT_LAUNCH_LOCAL
34645 13:02:46 (0) ** DCOM_RIGHT_LAUNCH_REMOTE
34646 13:02:46 (0) ** DCOM_RIGHT_ACTIVATE_LOCAL
34647 13:02:46 (0) ** DCOM_RIGHT_ACTIVATE_REMOTE
34648 13:02:46 (0) **
34649 13:02:46 (0) ** => The REMOVED ACE was part of the DEFAULT setup for the trustee.
34650 13:02:46 (0) ** Removing default security will cause some operations to fail!
34651 13:02:46 (0) ** It is possible to fix this issue by editing the security descriptor and adding the ACE.
34652 13:02:46 (0) ** For DCOM objects, this can be done with 'DCOMCNFG.EXE'.
34653 13:02:46 (0) **
34654 13:02:46 (0) **
34655 13:02:46 (0) ** DCOM security warning(s) detected: .................................................................................. 0.
34656 13:02:46 (0) ** DCOM security error(s) detected: .................................................................................... 14.
34657 13:02:46 (0) ** WMI security warning(s) detected: ................................................................................... 0.
34658 13:02:46 (0) ** WMI security error(s) detected: ..................................................................................... 0.
34659 13:02:46 (0) **
34660 13:02:46 (1) !! ERROR: Overall DCOM security status: ................................................................................ ERROR!
34661 13:02:46 (0) ** Overall WMI security status: ........................................................................................ OK.
34662 13:02:46 (0) ** - Started at 'Root' --------------------------------------------------------------------------------------------------------------
34663 13:02:46 (0) ** INFO: WMI permanent SUBSCRIPTION(S): ................................................................................ 1.
34664 13:02:46 (0) ** - ROOT/SUBSCRIPTION, NTEventLogEventConsumer.Name="SCM Event Log Consumer".
34665 13:02:46 (0) ** 'select * from MSFT_SCMEventLogEvent'
34666 13:02:46 (0) **
34667 13:02:46 (0) ** WMI TIMER instruction(s): ........................................................................................... NONE.
34668 13:02:46 (0) ** INFO: WMI namespace(s) requiring PACKET PRIVACY: .................................................................... 3 NAMESPACE(S)!
34669 13:02:46 (0) ** - ROOT/CIMV2/SECURITY/MICROSOFTTPM.
34670 13:02:46 (0) ** - ROOT/CIMV2/TERMINALSERVICES.
34671 13:02:46 (0) ** - ROOT/SERVICEMODEL.
34672 13:02:46 (0) ** => When remotely connecting, the namespace(s) listed require(s) the WMI client to
34673 13:02:46 (0) ** use an encrypted connection by specifying the PACKET PRIVACY authentication level.
34674 13:02:46 (0) ** (RPC_C_AUTHN_LEVEL_PKT_PRIVACY or PktPrivacy flags)
34675 13:02:46 (0) ** i.e. 'WMIC.EXE /NODE:"ISWDC2" /AUTHLEVEL:Pktprivacy /NAMESPACE:\\ROOT\SERVICEMODEL Class __SystemSecurity'
34676 13:02:46 (0) **
34677 13:02:46 (0) ** WMI MONIKER CONNECTIONS: ............................................................................................ OK.
34678 13:02:46 (0) ** WMI CONNECTIONS: .................................................................................................... OK.
34679 13:02:46 (1) !! ERROR: WMI GET operation errors reported: ........................................................................... 32 ERROR(S)!
34680 13:02:46 (0) ** - Root/CIMV2, MSFT_NetInvalidDriverDependency, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34681 13:02:46 (0) ** MOF Registration: ''
34682 13:02:46 (0) ** - Root/CIMV2, Win32_OsBaselineProvider, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34683 13:02:46 (0) ** MOF Registration: ''
34684 13:02:46 (0) ** - Root/CIMV2, Win32_OsBaseline, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34685 13:02:46 (0) ** MOF Registration: ''
34686 13:02:46 (0) ** - Root/CIMV2, Win32_DriverVXD, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34687 13:02:46 (0) ** MOF Registration: ''
34688 13:02:46 (0) ** - Root/CIMV2, Win32_PerfFormattedData_BITS_BITSNetUtilization, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34689 13:02:46 (0) ** MOF Registration: ''
34690 13:02:46 (0) ** - Root/CIMV2, Win32_PerfRawData_BITS_BITSNetUtilization, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34691 13:02:46 (0) ** MOF Registration: ''
34692 13:02:46 (0) ** - Root/CIMV2, Win32_PerfFormattedData_Counters_GenericIKEandAuthIP, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34693 13:02:46 (0) ** MOF Registration: ''
34694 13:02:46 (0) ** - Root/CIMV2, Win32_PerfRawData_Counters_GenericIKEandAuthIP, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34695 13:02:46 (0) ** MOF Registration: ''
34696 13:02:46 (0) ** - Root/CIMV2, Win32_PerfFormattedData_Counters_IPsecAuthIPv4, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34697 13:02:46 (0) ** MOF Registration: ''
34698 13:02:46 (0) ** - Root/CIMV2, Win32_PerfRawData_Counters_IPsecAuthIPv4, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34699 13:02:46 (0) ** MOF Registration: ''
34700 13:02:46 (0) ** - Root/CIMV2, Win32_PerfFormattedData_Counters_IPsecAuthIPv6, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34701 13:02:46 (0) ** MOF Registration: ''
34702 13:02:46 (0) ** - Root/CIMV2, Win32_PerfRawData_Counters_IPsecAuthIPv6, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34703 13:02:46 (0) ** MOF Registration: ''
34704 13:02:46 (0) ** - Root/CIMV2, Win32_PerfFormattedData_Counters_IPsecIKEv4, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34705 13:02:46 (0) ** MOF Registration: ''
34706 13:02:46 (0) ** - Root/CIMV2, Win32_PerfRawData_Counters_IPsecIKEv4, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34707 13:02:46 (0) ** MOF Registration: ''
34708 13:02:46 (0) ** - Root/CIMV2, Win32_PerfFormattedData_Counters_IPsecIKEv6, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34709 13:02:46 (0) ** MOF Registration: ''
34710 13:02:46 (0) ** - Root/CIMV2, Win32_PerfRawData_Counters_IPsecIKEv6, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34711 13:02:46 (0) ** MOF Registration: ''
34712 13:02:46 (0) ** - Root/CIMV2, Win32_PerfFormattedData_TermService_TerminalServices, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34713 13:02:46 (0) ** MOF Registration: ''
34714 13:02:46 (0) ** - Root/CIMV2, Win32_PerfRawData_TermService_TerminalServices, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34715 13:02:46 (0) ** MOF Registration: ''
34716 13:02:46 (0) ** - Root/WMI, ReserveDisjoinThread, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34717 13:02:46 (0) ** MOF Registration: ''
34718 13:02:46 (0) ** - Root/WMI, ReserveLateCount, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34719 13:02:46 (0) ** MOF Registration: ''
34720 13:02:46 (0) ** - Root/WMI, ReserveJoinThread, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34721 13:02:46 (0) ** MOF Registration: ''
34722 13:02:46 (0) ** - Root/WMI, ReserveDelete, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34723 13:02:46 (0) ** MOF Registration: ''
34724 13:02:46 (0) ** - Root/WMI, ReserveBandwidth, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34725 13:02:46 (0) ** MOF Registration: ''
34726 13:02:46 (0) ** - Root/WMI, ReserveCreate, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34727 13:02:46 (0) ** MOF Registration: ''
34728 13:02:46 (0) ** - Root/WMI, SystemConfig_PhyDisk, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34729 13:02:46 (0) ** MOF Registration: ''
34730 13:02:46 (0) ** - Root/WMI, SystemConfig_Video, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34731 13:02:46 (0) ** MOF Registration: ''
34732 13:02:46 (0) ** - Root/WMI, SystemConfig_IDEChannel, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34733 13:02:46 (0) ** MOF Registration: ''
34734 13:02:46 (0) ** - Root/WMI, SystemConfig_NIC, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34735 13:02:46 (0) ** MOF Registration: ''
34736 13:02:46 (0) ** - Root/WMI, SystemConfig_Network, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34737 13:02:46 (0) ** MOF Registration: ''
34738 13:02:46 (0) ** - Root/WMI, SystemConfig_CPU, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34739 13:02:46 (0) ** MOF Registration: ''
34740 13:02:46 (0) ** - Root/WMI, SystemConfig_LogDisk, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34741 13:02:46 (0) ** MOF Registration: ''
34742 13:02:46 (0) ** - Root/WMI, SystemConfig_Power, 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found.
34743 13:02:46 (0) ** MOF Registration: ''
34744 13:02:46 (0) ** => When a WMI performance class is missing (i.e. 'Win32_PerfRawData_TermService_TerminalServices'), it is generally due to
34745 13:02:46 (0) ** a lack of buffer refresh of the WMI class provider exposing the WMI performance counters.
34746 13:02:46 (0) ** You can refresh the WMI class provider buffer with the following command:
34747 13:02:46 (0) **
34748 13:02:46 (0) ** i.e. 'WINMGMT.EXE /SYNCPERF'
34749 13:02:46 (0) **
34750 13:02:46 (0) ** WMI MOF representations: ............................................................................................ OK.
34751 13:02:46 (0) ** WMI QUALIFIER access operations: .................................................................................... OK.
34752 13:02:46 (0) ** WMI ENUMERATION operations: ......................................................................................... OK.
34753 13:02:46 (0) ** WMI EXECQUERY operations: ........................................................................................... OK.
34754 13:02:46 (2) !! WARNING: WMI GET VALUE operation errors reported: ................................................................... 5 WARNING(S)!
34755 13:02:46 (0) ** - Root, Instance: __EventConsumerProviderCacheControl=@, Property: ClearAfter='00000000000030.000000:000' (Expected default='00000000000500.000000:000').
34756 13:02:46 (0) ** - Root, Instance: __EventProviderCacheControl=@, Property: ClearAfter='00000000000030.000000:000' (Expected default='00000000000500.000000:000').
34757 13:02:46 (0) ** - Root, Instance: __EventSinkCacheControl=@, Property: ClearAfter='00000000000015.000000:000' (Expected default='00000000000230.000000:000').
34758 13:02:46 (0) ** - Root, Instance: __ObjectProviderCacheControl=@, Property: ClearAfter='00000000000030.000000:000' (Expected default='00000000000500.000000:000').
34759 13:02:46 (0) ** - Root, Instance: __PropertyProviderCacheControl=@, Property: ClearAfter='00000000000030.000000:000' (Expected default='00000000000500.000000:000').
34760 13:02:46 (0) **
34761 13:02:46 (0) ** WMI WRITE operations: ............................................................................................... NOT TESTED.
34762 13:02:46 (0) ** WMI PUT operations: ................................................................................................. NOT TESTED.
34763 13:02:46 (0) ** WMI DELETE operations: .............................................................................................. NOT TESTED.
34764 13:02:46 (0) ** WMI static instances retrieved: ..................................................................................... 1822.
34765 13:02:46 (0) ** WMI dynamic instances retrieved: .................................................................................... 0.
34766 13:02:46 (0) ** WMI instance request cancellations (to limit performance impact): ................................................... 1.
34767 13:02:46 (0) ** ----------------------------------------------------------------------------------------------------------------------------------
34768 13:02:46 (0) ** # of Event Log events BEFORE WMIDiag execution since the last 20 day(s):
34769 13:02:46 (0) ** DCOM: ............................................................................................................. 0.
34770 13:02:46 (0) ** WINMGMT: .......................................................................................................... 0.
34771 13:02:46 (0) ** WMIADAPTER: ....................................................................................................... 0.
34772 13:02:46 (0) **
34773 13:02:46 (0) ** # of additional Event Log events AFTER WMIDiag execution:
34774 13:02:46 (0) ** DCOM: ............................................................................................................. 0.
34775 13:02:46 (0) ** WINMGMT: .......................................................................................................... 0.
34776 13:02:46 (0) ** WMIADAPTER: ....................................................................................................... 0.
34777 13:02:46 (0) **
34778 13:02:46 (0) ** 32 error(s) 0x80041002 - (WBEM_E_NOT_FOUND) Object cannot be found
34779 13:02:46 (0) ** => This error is typically a WMI error. This WMI error is due to:
34780 13:02:46 (0) ** - a missing WMI class definition or object.
34781 13:02:46 (0) ** (See any GET, ENUMERATION, EXECQUERY and GET VALUE operation failures).
34782 13:02:46 (0) ** You can correct the missing class definitions by:
34783 13:02:46 (0) ** - Manually recompiling the MOF file(s) with the 'MOFCOMP <FileName.MOF>' command.
34784 13:02:46 (0) ** Note: You can build a list of classes in relation with their WMI provider and MOF file with WMIDiag.
34785 13:02:46 (0) ** (This list can be built on a similar and working WMI Windows installation)
34786 13:02:46 (0) ** The following command line must be used:
34787 13:02:46 (0) ** i.e. 'WMIDiag CorrelateClassAndProvider'
34788 13:02:46 (0) ** Note: When a WMI performance class is missing, you can manually resynchronize performance counters
34789 13:02:46 (0) ** with WMI by starting the ADAP process.
34790 13:02:46 (0) ** - a WMI repository corruption.
34791 13:02:46 (0) ** In such a case, you must rerun WMIDiag with 'WriteInRepository' parameter
34792 13:02:46 (0) ** to validate the WMI repository operations.
34793 13:02:46 (0) ** Note: ENSURE you are an administrator with FULL access to WMI EVERY namespaces of the computer before
34794 13:02:46 (0) ** executing the WriteInRepository command. To write temporary data from the Root namespace, use:
34795 13:02:46 (0) ** i.e. 'WMIDiag WriteInRepository=Root'
34796 13:02:46 (0) ** - If the WriteInRepository command fails, while being an Administrator with ALL accesses to ALL namespaces
34797 13:02:46 (0) ** the WMI repository must be reconstructed.
34798 13:02:46 (0) ** Note: The WMI repository reconstruction requires to locate all MOF files needed to rebuild the repository,
34799 13:02:46 (0) ** otherwise some applications may fail after the reconstruction.
34800 13:02:46 (0) ** This can be achieved with the following command:
34801 13:02:46 (0) ** i.e. 'WMIDiag ShowMOFErrors'
34802 13:02:46 (0) ** Note: The repository reconstruction must be a LAST RESORT solution and ONLY after executing
34803 13:02:46 (0) ** ALL fixes previously mentioned.
34804 13:02:46 (2) !! WARNING: Static information stored by external applications in the repository will be LOST! (i.e. SMS Inventory)
34805 13:02:46 (0) **
34806 13:02:46 (0) ** ----------------------------------------------------------------------------------------------------------------------------------
34807 13:02:46 (0) ** WMI Registry key setup: ............................................................................................. OK.
34808 13:02:46 (0) ** ----------------------------------------------------------------------------------------------------------------------------------
34809 13:02:46 (0) ** ----------------------------------------------------------------------------------------------------------------------------------
34810 13:02:46 (0) ** ----------------------------------------------------------------------------------------------------------------------------------
34811 13:02:46 (0) ** ----------------------------------------------------------------------------------------------------------------------------------
34812 13:02:46 (0) **
34813 13:02:46 (0) ** ----------------------------------------------------------------------------------------------------------------------------------
34814 13:02:46 (0) ** ------------------------------------------------------ WMI REPORT: END -----------------------------------------------------------
34815 13:02:46 (0) ** ----------------------------------------------------------------------------------------------------------------------------------
34816 13:02:46 (0) **
34817 13:02:46 (0) ** ERROR: WMIDiag detected issues that could prevent WMI to work properly!. Check 'C:\USERS\ABCDEF\APPDATA\LOCAL\TEMP\WMIDIAG-V2.1_2K8R2.SRV.SP1.64_ISWDC2_2014.05.22_12.49.13.LOG' for details.
34818 13:02:46 (0) **
34819 13:02:46 (0) ** WMIDiag v2.1 ended on Donnerstag, 22. Mai 2014 at 13:02 (W:89 E:52 S:1).
There are a lot of error in the report and I don't know, whether they are relevant or how to solve them. To my current knowledge, I need to solve at least some of them so that I can access the local WMI repository again and get replication back working.
But after hours of research I am stuck. Any hints are greatly appreciated.
Regards,
OliverI don't know why, but soon after posting this, I found a solution to the problem. The WMI part was solved in this thread:
http://social.technet.microsoft.com/Forums/windowsserver/en-US/953be9ef-e9e3-4885-a5c4-47fc475ba562/dfs-is-not-working-anymore?forum=winserverfiles
The relevant portion is this:
Open a CMD prompt in %windir%\system32\wbem
mofcomp dfsrprovs.mof
net stop winmgmt
net start winmgmt
net start iphlpsvc
net stop dfsr
net start dfsr
I don't know why recompiling of all mof did not solve the problem, but the solution above did. Restarting the DCs solved the communication issue. I don't know why the primary DC forgot about the WMI DFS provider or why communication failed. However, it is
working again, it seems. -
I apologize in advance for the rambling novella, but I tried to include as many details ahead of time as I could.
I guess like most issues, this one's been evolving for a while, it started out with us trying to add a new member
to a replication group that's on a subnet without connectivity to the FSMO roles holder. I'll try to describe the
layout as best as I can up front.
The AD only has one domain & both the forest & domain are at 2008R2 function level. We've got two sites defined in
Sites & Services, Site A is an off-site datacenter with one associated subnet & Site B with 6 associated subnets, A-F.
The two sites are connected by a WAN link from a cable provider. Subnets E & F at Site B have no connectivity to Site A
across that WAN, only what's available through the front side of the datacenter through the public Internet. The network
engineering group involved refuses to route that WAN traffic to those two subnets & we've got no recourse against that
decision; so I'm trying to find a way to accomplish this without that if possible.
The FSMO roles holder is located at Site A. I know that I can define a Site C, add Subnets E & F to that site, & then
configure an SMTP site link between Sites A & C, but that only handles AD replication, correct? That still wouldn't allow me, for example,
to enumerate DFS namespaces from subnets E & F, or to add a fileserver on either of those subnets as a member to an existing
DFS replication group, right? Also, root scalability is enabled on all the namespace shares.
Is there a way to accomplish both of these things without transferring the FSMO roles from the original DC at Site A to, say,
the bridgehead DC at Site B?
When the infrastructure was originally setup by a former analyst, the topology was much more simple & everything was left
under the Default First Site & no sites/subnets were setup until fairly recently to resolve authentication issues on
Subnets E & F... I bring this up just to say, the FSMO roles holder has held them throughout the build out & addition of
all sorts of systems & I'm honestly not sure what, if anything, the transfer of those roles will break.
I definitely don't claim to be an expert in any of this, I'll be the first to say that I'm a work-in-progress on this AD design stuff,
I'm all for R'ing the FM, but frankly I'm dragging bottom at this point in finding the right FM. I've been digging around
on Google, forums, & TechNet for the past week or so as this has evolved, but no resolution yet.
On VMs & machines on subnets E & F when I go to DFS Management -> Namespace -> Add Namespaces to Display..., none show up
automatically & when I click Show Namespaces, after a few seconds I get "The namespaces on DOMAIN cannot be enumerated. The
specified domain either does not exist or could not be contacted". If I run a dfsutil /pktinfo, nothing shows except \sysvol
but I can access the domain-based DFS shares through Windows Explorer with the UNC path \\DOMAIN-FQDN\Share-Name then when
I run a dfsutil /pktinfo it shows all the shares that I've accessed so far.
So either I'm doing something wrong, or, for some random large, multinational company, every sunbet & fileserver one wants
to add to a DFS Namespace has to be able to contact the FSMO roles holder? Or, are those ADs broken down with a child domain
for each Site & a FSMO roles holder for that child domain is located in each site?Hi,
A DC in siteB should helpful. I still not see any article mentioned that a DFS client have to connect to PDC every time trying to access a DFS domain based namespace.
Please see following article. I pasted a part of it below:
http://technet.microsoft.com/en-us/library/cc782417(v=ws.10).aspx
Domain controllers play numerous roles in DFS:
Domain controllers store DFS metadata in Active Directory about domain-based namespaces. DFS metadata consists of information about entire namespace, including the root, root targets, links, link targets, and settings. By default,root servers
that host domain-based namespaces periodically poll the domain controller acting as the primary domain controller (PDC) emulator master to obtain an updated version of the DFS metadata and store this metadata in memory.
So Other DC needs to connect PDC for an updated metadata.
Whenever an administrator makes a change to a domain-based namespace, the
change is made on the domain controller acting as the PDC emulator master and is then replicated (via Active Directory replication) to other domain controllers in the domain.
Domain Name Referral Cache
A domain name referral contains the NetBIOS and DNS names of the local domain, all trusted domains in the forest, and domains in trusted forests. A
DFS client requests a domain name referral from a domain controller to determine the domains in which the clients can access domain-based namespaces.
Domain Controller Referral Cache
A domain controller referral contains the NetBIOS and DNS names of the domain controllers for the list of domains it has cached. A DFS client requests a domain controller referral from a domain controller (in the client’s domain)
to determine which domain controllers can provide a referral for a domain-based namespace.
Domain-based Root Referral Cache
The domain-based root referrals in this memory cache do not store targets in any particular order. The targets are sorted according to the target selection method only when requested from the client. Also, these referrals are based on DFS metadata stored
on the local domain controller, not the PDC emulator master.
Thus it seems to be acceptable to have a disconnect between sites shortly when cache is still working on siteB.
If you have any feedback on our support, please send to [email protected]. -
BSOD on Server 2012 running dfs namespace and dfs replication roles with deduplication
Hello,
I have recently setup 2 dfsn & dfsr servers, both 2012 one physical the other virtual.
The idea is to have one server as primary and the other as a failover \ DR.
The primary server is virtual and connects via mpio \ iscsi to a dell san, using the provided dell DSM Drivers.
The secondary server is physical with local disk for storage.
I copy files to a namespace setup to always prefer the primary server, these files are then replicated across to the secondary.
I have also turned on deduplication on both servers to get the most out of the available storage.
This has been working well for 6 months or so, there have however been 2-3 occasions where the primary virtual server has crashed and blue screened causing the DFSR database to undergo a full consistency check.
The bug check errors i have managed to extract from the Memory.dmp and mini dump are as follows:
* Bugcheck Analysis
REFERENCE_BY_POINTER (18)
Arguments:
Arg1: 0000000000000000, Object type of the object whose reference count is being lowered
Arg2: fffffa80379a3070, Object whose reference count is being lowered
Arg3: 0000000000000002, Reserved
Arg4: ffffffffffffffff, Reserved
The reference count of an object is illegal for the current state of the object.
Each time a driver uses a pointer to an object the driver calls a kernel routine
to increment the reference count of the object. When the driver is done with the
pointer the driver calls another kernel routine to decrement the reference count.
Drivers must match calls to the increment and decrement routines. This bugcheck
can occur because an object's reference count goes to zero while there are still
open handles to the object, in which case the fourth parameter indicates the number
of opened handles. It may also occur when the object?s reference count drops below zero
whether or not there are open handles to the object, and in that case the fourth parameter
contains the actual value of the pointer references count.
Debugging Details:
DEFAULT_BUCKET_ID: WIN8_DRIVER_FAULT
BUGCHECK_STR: 0x18
PROCESS_NAME: dfsrs.exe
CURRENT_IRQL: 0
ANALYSIS_VERSION: 6.3.9600.17029 (debuggers(dbg).140219-1702) amd64fre
LAST_CONTROL_TRANSFER: from fffff800999ee0d7 to fffff8009985a440
STACK_TEXT:
fffff880`0bf3fb48 fffff800`999ee0d7 : 00000000`00000018 00000000`00000000 fffffa80`379a3070 00000000`00000002 : nt!KeBugCheckEx
fffff880`0bf3fb50 fffff800`99c33529 : fffffa80`379a3070 fffff8a0`0244adc0 00000000`000017e4 0000001b`930b60d8 : nt! ?? ::FNODOBFM::`string'+0x38605
fffff880`0bf3fb90 fffff800`99859453 : fffffa80`4063db00 fffffa80`4063db00 fffff880`0bf3fcc0 00000000`00000001 : nt!NtClose+0x239
fffff880`0bf3fc40 000007ff`5e8d2cda : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : nt!KiSystemServiceCopyEnd+0x13
0000001b`9069f398 00000000`00000000 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : 0x000007ff`5e8d2cda
STACK_COMMAND: kb
FOLLOWUP_IP:
nt! ?? ::FNODOBFM::`string'+38605
fffff800`999ee0d7 cc int 3
SYMBOL_STACK_INDEX: 1
SYMBOL_NAME: nt! ?? ::FNODOBFM::`string'+38605
FOLLOWUP_NAME: MachineOwner
MODULE_NAME: nt
IMAGE_NAME: ntkrnlmp.exe
DEBUG_FLR_IMAGE_TIMESTAMP: 51a966cd
IMAGE_VERSION: 6.2.9200.16628
BUCKET_ID_FUNC_OFFSET: 38605
FAILURE_BUCKET_ID: 0x18_OVER_DEREFERENCE_nt!_??_::FNODOBFM::_string_
BUCKET_ID: 0x18_OVER_DEREFERENCE_nt!_??_::FNODOBFM::_string_
ANALYSIS_SOURCE: KM
FAILURE_ID_HASH_STRING: km:0x18_over_dereference_nt!_??_::fnodobfm::_string_
FAILURE_ID_HASH: {eaf19261-0688-f327-a17d-6f7960ac4ebd}
Followup: MachineOwner
rax=0000000000000000 rbx=ffffffffffffffff rcx=0000000000000018
rdx=0000000000000000 rsi=fffffa80379a3070 rdi=00000000fffc000c
rip=fffff8009985a440 rsp=fffff8800bf3fb48 rbp=fffffa80379a3040
r8=fffffa80379a3070 r9=0000000000000002 r10=fffffa8030d89190
r11=fffffa804063db00 r12=00000000000017e4 r13=0000000000000000
r14=fffff8a00a548f90 r15=0000000000000000
iopl=0 nv up ei pl zr na po nc
cs=0010 ss=0018 ds=002b es=002b fs=0053 gs=002b efl=00000246
nt!KeBugCheckEx:
fffff800`9985a440 48894c2408 mov qword ptr [rsp+8],rcx ss:0018:fffff880`0bf3fb50=0000000000000018
Child-SP RetAddr : Args to Child
: Call Site
fffff880`0bf3fb48 fffff800`999ee0d7 : 00000000`00000018 00000000`00000000 fffffa80`379a3070 00000000`00000002 : nt!KeBugCheckEx
fffff880`0bf3fb50 fffff800`99c33529 : fffffa80`379a3070 fffff8a0`0244adc0 00000000`000017e4 0000001b`930b60d8 : nt! ?? ::FNODOBFM::`string'+0x38605
fffff880`0bf3fb90 fffff800`99859453 : fffffa80`4063db00 fffffa80`4063db00 fffff880`0bf3fcc0 00000000`00000001 : nt!NtClose+0x239
fffff880`0bf3fc40 000007ff`5e8d2cda : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : nt!KiSystemServiceCopyEnd+0x13 (TrapFrame @ fffff880`0bf3fc40)
0000001b`9069f398 00000000`00000000 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : 0x000007ff`5e8d2cda
start end module name
fffff800`987b1000 fffff800`987ba000 kd kd.dll Thu Jul 26 03:30:34 2012 (5010ABCA)
fffff800`99800000 fffff800`99f4c000 nt ntkrnlmp.exe Sat Jun 01 04:13:17 2013 (51A966CD)
fffff800`99f4c000 fffff800`99fb8000 hal hal.dll Wed Oct 24 04:03:21 2012 (50875A79)
fffff880`00a00000 fffff880`00a34000 ataport ataport.SYS Thu Jul 26 03:29:04 2012 (5010AB70)
fffff880`00a34000 fffff880`00a51000 lsi_sas lsi_sas.sys Fri May 11 20:40:21 2012 (4FAD6B25)
fffff880`00a51000 fffff880`00a5e000 serenum serenum.sys Thu Jul 26 03:30:13 2012 (5010ABB5)
fffff880`00a5e000 fffff880`00a6c000 fdc fdc.sys Thu Jul 26 03:30:15 2012 (5010ABB7)
fffff880`00a7b000 fffff880`00adb000 volmgrx volmgrx.sys Thu Jul 26 03:29:59 2012 (5010ABA7)
fffff880`00adb000 fffff880`00ae4000 intelide intelide.sys Thu Jul 26 03:29:52 2012 (5010ABA0)
fffff880`00ae4000 fffff880`00af3000 PCIIDEX PCIIDEX.SYS Thu Jul 26 03:29:09 2012 (5010AB75)
fffff880`00af3000 fffff880`00b56000 md3dsm md3dsm.sys Wed Aug 22 22:14:46 2012 (50354BC6)
fffff880`00b56000 fffff880`00b87000 msdsm msdsm.sys Sat Oct 05 04:32:09 2013 (524F8839)
fffff880`00b87000 fffff880`00ba0000 vmci vmci.sys Tue May 01 02:14:27 2012 (4F9F38F3)
fffff880`00ba0000 fffff880`00bb5000 vsock vsock.sys Fri Aug 30 20:25:34 2013 (5220F1AE)
fffff880`00bb5000 fffff880`00bcf000 mountmgr mountmgr.sys Thu Jul 26 03:29:33 2012 (5010AB8D)
fffff880`00bcf000 fffff880`00bd9000 atapi atapi.sys Thu Jul 26 03:30:33 2012 (5010ABC9)
fffff880`00bd9000 fffff880`00bf0000 vmxnet3n61x64 vmxnet3n61x64.sys Fri Sep 27 10:40:11 2013 (5245527B)
fffff880`00bf0000 fffff880`00bfa000 pnpmem pnpmem.sys Thu Jul 26 03:30:11 2012 (5010ABB3)
fffff880`00c40000 fffff880`00c9f000 mcupdate_GenuineIntel mcupdate_GenuineIntel.dll Thu Jul 26 03:30:12 2012 (5010ABB4)
fffff880`00c9f000 fffff880`00cfb000 CLFS CLFS.SYS Thu Jul 26 03:29:39 2012 (5010AB93)
fffff880`00cfb000 fffff880`00d1e000 tm tm.sys Thu Jul 26 03:29:01 2012 (5010AB6D)
fffff880`00d1e000 fffff880`00d33000 PSHED PSHED.dll Thu Jul 26 05:53:53 2012 (5010CD61)
fffff880`00d33000 fffff880`00d3d000 BOOTVID BOOTVID.dll Thu Jul 26 03:30:22 2012 (5010ABBE)
fffff880`00d3d000 fffff880`00dbc000 CI CI.dll Thu Mar 28 03:30:42 2013 (5153B962)
fffff880`00dbc000 fffff880`00de1000 rasl2tp rasl2tp.sys Thu Jul 26 03:23:16 2012 (5010AA14)
fffff880`00e00000 fffff880`00e49000 spaceport spaceport.sys Sat Oct 05 04:32:08 2013 (524F8838)
fffff880`00e49000 fffff880`00e61000 volmgr volmgr.sys Thu Jul 26 03:29:22 2012 (5010AB82)
fffff880`00e61000 fffff880`00ea9000 vm3dmp vm3dmp.sys Wed Oct 09 05:25:53 2013 (5254DAD1)
fffff880`00eb5000 fffff880`00f41000 cng cng.sys Thu Oct 11 06:17:34 2012 (5076566E)
fffff880`00f41000 fffff880`00f5b000 raspppoe raspppoe.sys Thu Jul 26 03:24:55 2012 (5010AA77)
fffff880`00f5c000 fffff880`00f99000 mpio mpio.sys Sat Sep 28 04:37:24 2013 (52464EF4)
fffff880`00f99000 fffff880`00fd3000 md3utm md3utm.sys Wed Aug 22 22:14:56 2012 (50354BD0)
fffff880`00fd3000 fffff880`00fef000 intelppm intelppm.sys Tue Nov 06 03:55:02 2012 (50988A16)
fffff880`01000000 fffff880`0106d000 ACPI ACPI.sys Thu Sep 20 07:09:16 2012 (505AB30C)
fffff880`01075000 fffff880`010d8000 msrpc msrpc.sys Thu Jul 26 03:28:37 2012 (5010AB55)
fffff880`010d8000 fffff880`0119a000 Wdf01000 Wdf01000.sys Sat Jun 22 04:13:05 2013 (51C51641)
fffff880`0119a000 fffff880`011aa000 WDFLDR WDFLDR.SYS Sat Jun 22 04:14:38 2013 (51C5169E)
fffff880`011aa000 fffff880`011c1000 acpiex acpiex.sys Thu Jul 26 03:25:57 2012 (5010AAB5)
fffff880`011c1000 fffff880`011cc000 WppRecorder WppRecorder.sys Thu Jul 26 03:29:07 2012 (5010AB73)
fffff880`011cc000 fffff880`011d6000 WMILIB WMILIB.SYS Thu Jul 26 03:30:04 2012 (5010ABAC)
fffff880`011d6000 fffff880`011f7000 raspptp raspptp.sys Thu Jul 26 03:23:13 2012 (5010AA11)
fffff880`01400000 fffff880`0140d000 vdrvroot vdrvroot.sys Thu Jul 26 03:27:29 2012 (5010AB11)
fffff880`0140d000 fffff880`01424000 pdc pdc.sys Fri Mar 01 04:58:34 2013 (5130357A)
fffff880`01424000 fffff880`0143e000 partmgr partmgr.sys Wed Jan 09 04:01:42 2013 (50ECEBA6)
fffff880`01444000 fffff880`0153f000 NDIS NDIS.SYS Sat Jun 15 06:11:35 2013 (51BBF787)
fffff880`0153f000 fffff880`015ae000 NETIO NETIO.SYS Thu Oct 11 06:16:20 2012 (50765624)
fffff880`015ae000 fffff880`015b8000 msisadrv msisadrv.sys Thu Jul 26 03:28:02 2012 (5010AB32)
fffff880`015b8000 fffff880`015f5000 pci pci.sys Thu Jul 26 03:27:43 2012 (5010AB1F)
fffff880`01800000 fffff880`01816000 datascrn datascrn.sys Thu Jul 26 03:29:13 2012 (5010AB79)
fffff880`01816000 fffff880`01824000 cbafilt cbafilt.sys Thu Jul 26 03:29:05 2012 (5010AB71)
fffff880`01824000 fffff880`0186c000 msiscsi msiscsi.sys Mon Feb 03 16:23:09 2014 (52EFC26D)
fffff880`0186c000 fffff880`01877000 kdnic kdnic.sys Thu Jul 26 03:27:41 2012 (5010AB1D)
fffff880`01877000 fffff880`01889000 umbus umbus.sys Thu Jul 26 03:27:39 2012 (5010AB1B)
fffff880`01889000 fffff880`018a9000 i8042prt i8042prt.sys Thu Jul 26 03:28:50 2012 (5010AB62)
fffff880`018a9000 fffff880`018b8000 kbdclass kbdclass.sys Thu Jul 26 03:28:47 2012 (5010AB5F)
fffff880`018b8000 fffff880`018c7000 mouclass mouclass.sys Thu Jul 26 03:28:47 2012 (5010AB5F)
fffff880`018c7000 fffff880`018e5000 parport parport.sys Thu Jul 26 03:29:53 2012 (5010ABA1)
fffff880`018e5000 fffff880`018fd000 serial serial.sys Thu Jul 26 03:30:01 2012 (5010ABA9)
fffff880`018fd000 fffff880`01952000 storport storport.sys Mon Feb 03 16:23:24 2014 (52EFC27C)
fffff880`01952000 fffff880`019b2000 fltmgr fltmgr.sys Thu Jul 26 03:30:09 2012 (5010ABB1)
fffff880`019b2000 fffff880`019e0000 quota quota.sys Thu Jul 26 03:29:14 2012 (5010AB7A)
fffff880`019e0000 fffff880`019f4000 dfsrro dfsrro.sys Thu Jul 26 03:29:13 2012 (5010AB79)
fffff880`019f4000 fffff880`01a00000 BATTC BATTC.SYS Thu Oct 11 06:19:58 2012 (507656FE)
fffff880`01a00000 fffff880`01a2c000 tunnel tunnel.sys Thu Jul 26 03:23:04 2012 (5010AA08)
fffff880`01a2c000 fffff880`01a3b000 CompositeBus CompositeBus.sys Thu Jul 26 03:28:03 2012 (5010AB33)
fffff880`01a3b000 fffff880`01a45000 vmgencounter vmgencounter.sys Thu Jul 26 03:27:58 2012 (5010AB2E)
fffff880`01a45000 fffff880`01c2a000 Ntfs Ntfs.sys Sun Jan 26 23:28:35 2014 (52E59A23)
fffff880`01c2a000 fffff880`01c45000 ksecdd ksecdd.sys Thu Sep 20 07:09:16 2012 (505AB30C)
fffff880`01c45000 fffff880`01c56000 pcw pcw.sys Thu Jul 26 03:28:44 2012 (5010AB5C)
fffff880`01c56000 fffff880`01c60000 Fs_Rec Fs_Rec.sys Thu Jul 26 03:30:08 2012 (5010ABB0)
fffff880`01c60000 fffff880`01c8f000 ksecpkg ksecpkg.sys Thu Oct 11 06:16:46 2012 (5076563E)
fffff880`01c8f000 fffff880`01cc0000 cdrom cdrom.sys Thu Jul 26 03:26:36 2012 (5010AADC)
fffff880`01cc0000 fffff880`01d2b000 dedup dedup.sys Sat Oct 05 04:31:38 2013 (524F881A)
fffff880`01d2b000 fffff880`01d3a000 vmrawdsk vmrawdsk.sys Sun Dec 15 03:36:38 2013 (52AD23C6)
fffff880`01d3a000 fffff880`01d47000 BasicRender BasicRender.sys Thu Jul 26 03:28:51 2012 (5010AB63)
fffff880`01d47000 fffff880`01d53000 mssmbios mssmbios.sys Thu Jul 26 03:29:19 2012 (5010AB7F)
fffff880`01d53000 fffff880`01d64000 discache discache.sys Thu Jul 26 03:28:23 2012 (5010AB47)
fffff880`01d64000 fffff880`01d85000 dfsc dfsc.sys Wed Jan 15 23:42:58 2014 (52D71D02)
fffff880`01d85000 fffff880`01d91000 ndistapi ndistapi.sys Thu Sep 20 07:09:19 2012 (505AB30F)
fffff880`01d91000 fffff880`01dc0000 ndiswan ndiswan.sys Thu Jul 26 03:23:13 2012 (5010AA11)
fffff880`01dc0000 fffff880`01dde000 rassstp rassstp.sys Thu Jul 26 03:23:59 2012 (5010AA3F)
fffff880`01dde000 fffff880`01df6000 AgileVpn AgileVpn.sys Thu Jul 26 03:23:11 2012 (5010AA0F)
fffff880`01df6000 fffff880`01dfc400 CmBatt CmBatt.sys Thu Jul 26 03:29:20 2012 (5010AB80)
fffff880`01e00000 fffff880`01e54000 CLASSPNP CLASSPNP.SYS Sat Jun 29 04:07:45 2013 (51CE4F81)
fffff880`01e54000 fffff880`01e68000 crashdmp crashdmp.sys Fri Aug 30 04:11:28 2013 (52200D60)
fffff880`01e75000 fffff880`01e7e000 Null Null.SYS Thu Jul 26 03:30:16 2012 (5010ABB8)
fffff880`01e81000 fffff880`020ba000 tcpip tcpip.sys Wed Jan 22 04:28:22 2014 (52DF48E6)
fffff880`020ba000 fffff880`02122000 fwpkclnt fwpkclnt.sys Fri Mar 01 04:55:54 2013 (513034DA)
fffff880`02122000 fffff880`0213d000 wfplwfs wfplwfs.sys Thu Oct 10 04:32:19 2013 (52561FC3)
fffff880`0213d000 fffff880`02191000 volsnap volsnap.sys Sat Jun 01 04:10:22 2013 (51A9661E)
fffff880`02191000 fffff880`021a8000 mup mup.sys Thu Jul 26 03:30:00 2012 (5010ABA8)
fffff880`021a8000 fffff880`021b4000 npsvctrig npsvctrig.sys Thu Jul 26 03:27:33 2012 (5010AB15)
fffff880`021b4000 fffff880`021d0000 disk disk.sys Sat Oct 12 07:31:15 2013 (5258ECB3)
fffff880`021ed000 fffff880`021ff000 dfs dfs.sys Thu Jul 26 03:28:21 2012 (5010AB45)
fffff880`03800000 fffff880`03863000 mrxsmb mrxsmb.sys Tue Feb 05 22:29:08 2013 (511187B4)
fffff880`0389c000 fffff880`038eb000 ks ks.sys Sat Feb 02 07:25:50 2013 (510CBF7E)
fffff880`038eb000 fffff880`038f6000 rdpbus rdpbus.sys Thu Jul 26 03:28:19 2012 (5010AB43)
fffff880`038f6000 fffff880`0390a000 NDProxy NDProxy.SYS Tue Apr 09 03:33:41 2013 (51637E05)
fffff880`0390a000 fffff880`03915000 flpydisk flpydisk.sys Thu Jul 26 03:30:15 2012 (5010ABB7)
fffff880`03915000 fffff880`03922000 dump_diskdump dump_diskdump.sys Thu Jul 26 03:29:58 2012 (5010ABA6)
fffff880`03922000 fffff880`0393f000 dump_LSI_SAS dump_LSI_SAS.sys Fri May 11 20:40:21 2012 (4FAD6B25)
fffff880`0393f000 fffff880`03947000 HIDPARSE HIDPARSE.SYS Sat Jun 29 04:08:18 2013 (51CE4FA2)
fffff880`03947000 fffff880`03955000 monitor monitor.sys Fri Mar 01 04:56:18 2013 (513034F2)
fffff880`03955000 fffff880`0397d000 luafv luafv.sys Thu Jul 26 03:29:13 2012 (5010AB79)
fffff880`0397d000 fffff880`03991000 lltdio lltdio.sys Thu Jul 26 03:24:02 2012 (5010AA42)
fffff880`03991000 fffff880`039a9000 rspndr rspndr.sys Thu Jul 26 03:24:06 2012 (5010AA46)
fffff880`039a9000 fffff880`039c9000 bowser bowser.sys Thu Jul 26 03:28:01 2012 (5010AB31)
fffff880`039c9000 fffff880`039e0000 mpsdrv mpsdrv.sys Thu Oct 31 03:42:19 2013 (5271D19B)
fffff880`03c00000 fffff880`03c73000 rdbss rdbss.sys Sat May 04 05:47:00 2013 (518492C4)
fffff880`03c73000 fffff880`03c8d000 wanarp wanarp.sys Tue Apr 09 03:31:00 2013 (51637D64)
fffff880`03c8d000 fffff880`03c9b000 nsiproxy nsiproxy.sys Thu Jul 26 03:25:00 2012 (5010AA7C)
fffff880`03c9b000 fffff880`03ca3000 vmmouse vmmouse.sys Mon Jun 04 10:34:25 2012 (4FCC8121)
fffff880`03ca3000 fffff880`03e0c000 dxgkrnl dxgkrnl.sys Thu Sep 19 04:16:23 2013 (523A6C87)
fffff880`03e0c000 fffff880`03e1d000 watchdog watchdog.sys Thu Jul 26 03:29:05 2012 (5010AB71)
fffff880`03e1d000 fffff880`03e6b000 dxgmms1 dxgmms1.sys Wed Jan 09 03:58:58 2013 (50ECEB02)
fffff880`03e6b000 fffff880`03e7c000 BasicDisplay BasicDisplay.sys Thu Jul 26 03:29:08 2012 (5010AB74)
fffff880`03e7c000 fffff880`03e8e000 Npfs Npfs.SYS Thu Jul 26 03:30:26 2012 (5010ABC2)
fffff880`03e8e000 fffff880`03e9a000 Msfs Msfs.SYS Thu Jul 26 03:30:24 2012 (5010ABC0)
fffff880`03e9a000 fffff880`03ebc000 tdx tdx.sys Thu Jul 26 03:24:58 2012 (5010AA7A)
fffff880`03ebc000 fffff880`03eca000 TDI TDI.SYS Thu Jul 26 03:27:59 2012 (5010AB2F)
fffff880`03eca000 fffff880`03ed6000 ws2ifsl ws2ifsl.sys Thu Sep 20 07:09:50 2012 (505AB32E)
fffff880`03ed6000 fffff880`03f2e000 netbt netbt.sys Thu Jul 26 03:24:26 2012 (5010AA5A)
fffff880`03f2e000 fffff880`03fc4000 afd afd.sys Wed Sep 04 04:11:20 2013 (5226A4D8)
fffff880`03fc4000 fffff880`03fee000 pacer pacer.sys Thu Jul 26 03:23:05 2012 (5010AA09)
fffff880`03fee000 fffff880`03ffe000 netbios netbios.sys Thu Jul 26 03:28:19 2012 (5010AB43)
fffff880`03ffe000 fffff880`03fff480 swenum swenum.sys Thu Jul 26 03:28:53 2012 (5010AB65)
fffff880`0ac00000 fffff880`0acdf000 HTTP HTTP.sys Fri Mar 15 00:17:15 2013 (5142688B)
fffff880`0acdf000 fffff880`0ace7000 vmmemctl vmmemctl.sys Sun Dec 15 03:36:24 2013 (52AD23B8)
fffff880`0acf8000 fffff880`0ad43000 mrxsmb10 mrxsmb10.sys Thu Jul 26 03:23:06 2012 (5010AA0A)
fffff880`0ad43000 fffff880`0ad7e000 mrxsmb20 mrxsmb20.sys Tue Feb 05 22:28:36 2013 (51118794)
fffff880`0b200000 fffff880`0b20d000 condrv condrv.sys Thu Jul 26 03:30:08 2012 (5010ABB0)
fffff880`0b20d000 fffff880`0b2ae000 srv2 srv2.sys Tue Apr 09 03:33:02 2013 (51637DDE)
fffff880`0b2cd000 fffff880`0b399000 peauth peauth.sys Tue Apr 09 03:32:01 2013 (51637DA1)
fffff880`0b399000 fffff880`0b3a4000 secdrv secdrv.SYS Wed Sep 13 14:18:38 2006 (4508052E)
fffff880`0b3a4000 fffff880`0b3e8000 srvnet srvnet.sys Tue Apr 09 03:31:13 2013 (51637D71)
fffff880`0b3e8000 fffff880`0b3fa000 tcpipreg tcpipreg.sys Thu Jul 26 03:23:13 2012 (5010AA11)
fffff880`0b4e3000 fffff880`0b570000 srv srv.sys Thu Jul 26 03:25:28 2012 (5010AA98)
fffff880`0b570000 fffff880`0b57b000 rdpvideominiport rdpvideominiport.sys Fri Oct 12 06:48:28 2012 (5077AF2C)
fffff880`0b57b000 fffff880`0b5ac000 rdpdr rdpdr.sys Thu Jul 26 03:25:18 2012 (5010AA8E)
fffff880`0b5ac000 fffff880`0b5b9000 terminpt terminpt.sys Thu Jul 26 03:28:53 2012 (5010AB65)
fffff960`00118000 fffff960`00508000 win32k win32k.sys Sat Feb 08 04:34:05 2014 (52F5B3BD)
fffff960`006cb000 fffff960`006d4000 TSDDD TSDDD.dll Thu Jul 26 03:30:25 2012 (5010ABC1)
fffff960`00879000 fffff960`008af000 cdd cdd.dll Thu Jul 26 05:49:37 2012 (5010CC61)
fffff960`00a21000 fffff960`00a60000 RDPUDD RDPUDD.dll Fri Oct 12 06:50:01 2012 (5077AF89)
Unloaded modules:
fffff880`01e68000 fffff880`01e75000 dump_storport.sys
Timestamp: unavailable (00000000)
Checksum: 00000000
ImageSize: 0000D000
fffff880`021d0000 fffff880`021ed000 dump_LSI_SAS.sys
Timestamp: unavailable (00000000)
Checksum: 00000000
ImageSize: 0001D000
fffff880`021a8000 fffff880`021b4000 hwpolicy.sys
Timestamp: unavailable (00000000)
Checksum: 00000000
ImageSize: 0000C000
fffff880`00f41000 fffff880`00f5c000 sacdrv.sys
Timestamp: unavailable (00000000)
Checksum: 00000000
ImageSize: 0001B000
fffff880`00c33000 fffff880`00c40000 ApiSetSchema.dll
Timestamp: unavailable (00000000)
Checksum: 00000000
ImageSize: 0000D000
I have searched for others having a similar problem but have not managed to find much.
The memory dump at the time of the crash does seem to hint at a problem with DFSR.exe.
The setup seems to be running fine again now and is going through its consistency checks, it is just a major inconvenience and will only get worse as the DFS becomes busier and approaches capacity.
The plan was to put this setup into production however with the unpredictability of blue screen reboots I cannot see this happening until I can find a fix or work around.
I have yet to see this problem occur on the other (physical) server, this is pretty much identical in configuration apart from its storage access.
My thoughts are a possible bug in the DFSR component or a bug in the DSM Drivers used for the iSCSI SAN connection or maybe a combination of the two.
Any help, thoughts or suggestions greatly appreciated
ThanksHi,
Please install the current version of Dfssvc.exe Dfsc.sys Dfsrs.exe for Windows Server 2012.
List of currently available hotfixes for Distributed File System (DFS) technologies in Windows Server 2012 and Windows Server 2012 R2
http://support.microsoft.com/kb/2951262
The issue may be due to the DFSRoot folder has lost NTFS permission. Some reasons why DFS root lose ACLs Links are listed in the article below:
How to implement Windows Server 2003 Access-based Enumeration in a DFS environment
http://support.microsoft.com/kb/907458/en-us
You could use dfsutil to set NTFS permission: dfsutil property ACL \\DFS-namespace
Using the Windows Server 2008 DFSUTIL.EXE command line to manage DFS-Namespaces
http://blogs.technet.com/b/josebda/archive/2009/05/01/using-the-windows-server-2008-dfsutil-exe-command-line-to-manage-dfs-namespaces.aspx
To narrow down the issue, you could remove the DFS role to check if the issue related to the dfs namespace and dfs replication roles.
Regards,
Mandy
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place. -
Can't locate email content? All of a sudden my email content has disappeared from inside MacMail? The actual emails are coming through but I am unable to view them in the content area! Nothing has been done to have changed this?
Please read this whole message before doing anything.
This procedure is a test, not a solution. Don’t be disappointed when you find that nothing has changed after you complete it.
Step 1
The purpose of this step is to determine whether the problem is localized to your user account.
Enable guest logins* and log in as Guest. Don't use the Safari-only “Guest User” login created by “Find My Mac.”
While logged in as Guest, you won’t have access to any of your documents or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this behavior; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin.
Test while logged in as Guest. Same problem?
After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it.
*Note: If you’ve activated “Find My Mac” or FileVault, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing.
Step 2
The purpose of this step is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Please take this step regardless of the results of Step 1.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of Steps 1 and 2. -
I'm replicating between two servers in two sites (Server A - Server 2012 R2 STD, Server B - Server 2008 R2) over a VPN (Sonicwall Firewall). Though the initial replication seems to be
happening it is very slow (the folder in question is less than 3GB). I'm seeing these in the event viewer every few minutes:
The DFS Replication service is stopping communication with partner PPIFTC for replication group FTC due to an error. The service will retry the connection periodically.
Additional Information:
Error: 1726 (The remote procedure call failed.)
and then....
The DFS Replication service successfully established an inbound connection with partner PPIFTC for replication group FTC.
Here are all my troubleshooting steps (keep in mind that our VPN is going through a SonicWall <--I increased the TCP timeout to 24 hours):
-Increased TCP Timeout to 24 hours
-Added the following values on both sending and receiving members and rebooted server
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters
Value =DisableTaskOffload
Type = DWORD
Data = 1
Value =EnableTCPChimney
Type = DWORD
Data = 0
Value =EnableTCPA
Type = DWORD
Data = 0
Value =EnableRSS
Type = DWORD
Data = 0
---------------------------------more troubleshooting--------------------------
-Disabled AntiVirus on both members
-Made sure DFSR TCP ports 135 & 5722 are open
-Installed all hotfixes for 2008 R2 (http://support.microsoft.com/kb/968429) and rebooted
-Ran NETSTAT –ANOBP TCP and the DFS executable results are listed below:
Sending Member:
[DFSRs.exe]
TCP 10.x.x.x:53 0.0.0.0:0
LISTENING 1692
[DFSRs.exe]
TCP 10.x.x.x:54669
10.x.x.x:5722 TIME_WAIT 0
TCP 10.x.x.x:54673
10.x.x.x:5722 ESTABLISHED 1656
[DFSRs.exe]
TCP 10.x.x.x:64773
10.x.x.x:389 ESTABLISHED 1692
[DFSRs.exe]
TCP 10.x.x.x:64787
10.x.x.x:389 ESTABLISHED 1656
[DFSRs.exe]
TCP 10.x.x.x:64795
10.x.x.x:389 ESTABLISHED 2104
Receiving Member:
[DFSRs.exe]
TCP 10.x.x.x:56683
10.x.x.x:389 ESTABLISHED 7472
[DFSRs.exe]
TCP 10.x.x.x:57625
10.x.x.x:54886 ESTABLISHED 2808
[DFSRs.exe]
TCP 10.x.x.x:61759
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61760
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61763
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61764
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61770
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61771
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61774
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61775
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61776
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61777
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61778
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61779
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61784
10.x.x.x:52757 ESTABLISHED 7472
[DFSRs.exe]
TCP 10.x.x.x:63661
10.x.x.x:63781 ESTABLISHED 4880
------------------------------more troubleshooting--------------------------
-Increased Staging to 32GB
-Opened the ADSIedit.msc console to verify the "Authenticated Users" is set with the default READ permission on the following object:
a. The computer object of the DFS server
b. The DFSR-LocalSettings object under the DFS server computer object
-Ran
ping <var>10.x.x.x</var> -f -l 1472 and got replies back from both servers
-AD replication is successful on all partners
-Nslookup is working so DNS is working
-Updated NIC drivers on both servers
- I ran the following to set the Primary Member:
dfsradmin Membership Set /RGName:<replication group name> /RFName:<replicated folder name> /MemName:<primary member> /IsPrimary:True
Then Dfsrdiag Pollad /Member:<member name>
I'm seeing these errors in the dfsr logs:
20141014 19:28:17.746 9116 SRTR 957 [WARN] SERVER_EstablishSession Failed to establish a replicated folder session. connId:{45C8C309-4EDD-459A-A0BB-4C5FACD97D44} csId:{7AC7917F-F96F-411B-A4D8-6BB303B3C813}
Error:
+ [Error:9051(0x235b) UpstreamTransport::EstablishSession upstreamtransport.cpp:808 9116 C The content set is not ready]
+ [Error:9051(0x235b) OutConnection::EstablishSession outconnection.cpp:532 9116 C The content set is not ready]
+ [Error:9051(0x235b) OutConnection::EstablishSession outconnection.cpp:471 9116 C The content set is not ready]
---------------------------------------more troubleshooting-----------------------------
I've done a lot of research on the Internet and most of it is pointing to the same stuff I've tried. Does anyone have any other suggestions? Maybe I need to look somewhere
else on the server side or firewall side?
I tried replicating from a 2012 R2 server to another 2012 server and am getting the same events in the event log so maybe it's not a server issue.
Some other things I'm wondering:
-Could it be the speed of the NICs? Server A is a 2012 Server that has Hyper-V installed. NIC teaming was initially setup and since Hyper-V is installed the NIC is a "vEthernet
(Microsoft Network Adapter Multiplexor Driver Virtual Switch) running at a speed of 10.0Gbps whereas Server B is running a single NIC at 1.0Gbps
-Could occasional ping timeout's cause the issue? From time to time I get a timeout but it's not as often as the events I'm seeing. I'm getting 53ms pings. The folder
is only 3 GB so it shouldn't take that long to replicate but it's been days. The schedule I have set for replication is mostly all day except for our backup times which start at 11pm-5am. Throughout the rest of the time I have it set anywhere from
4Mbps to 64 Kbps. Server A is on a 5mb circuit and Server B is on a 10mb circuit.I'm seeing the same errors, all servers are running 2008 R2 x64. Across multiple sites, VPN is steady and reliably.
185 events from 12:28:21 to 12:49:25
Events are for all five servers (one per office, five total offices, no two in the same city, across three states).
Events are not limited to one replication group. I have quite a few replication groups, so I don't know for sure but I'm running under the reasonable assumption that none are spared.
Reminder from original post (and also, yes, same for me), the error is: Error: 1726 (The remote procedure call failed.)
Some way to figure out what code triggers an Event ID 5014, and what code therein specifies an Error 1726, would extremely helpful. Trying random command line/registry changes on live servers is exceptionally unappealing.
Side note, 1726 is referenced here:
https://support.microsoft.com/kb/976442?wa=wsignin1.0
But it says, "This RPC connection problem may be caused by an unstable WAN connection." I don't believe this is the case for my system.
It also says...
For most RPC connection problems, the DFS Replication service will try to obtain the files again without logging a warning or an error in the DFS Replication log. You can capture the network trace to determine whether the cause of the problem is at the network
layer. To examine the TCP ports that the DFS Replication service is using on replication partners, run the following command in a
Command Prompt window:
NETSTAT –ANOBP TCP
This returns all open TCP connections. The connections in question are "DFSRs.exe", which the command won't let you filter for.
Instead, I used the NETSTAT command as advertised, dumping output to info.txt:
NETSTAT -ANOBP TCP >> X:\info.txt
Then I opened Excel and manually opened the .TXT for the open wizard. I chose fixed-width fields based on the first row for each result, and then added a column:
=IF(A3="Can not", "Can not obtain ownership information", IF(LEFT(A3,1) = "[", A3&B3&C3, ""))
Dragging this down through the entire file let me see that row (Row F) as the file name. Some anomalies were present but none impacted DFSrs.exe results.
Finally, you can sort/filter (I sorted because I like being able to see everything, should I choose to) to get just the results you need, with the partial rows removed from the result set, or bumped to the end.
My server had 125 connections open.
That is a staggering number of connections to review, and I feel like I'm looking for a needle in a haystack.
I'll see if I can find anything useful out, but a better solution would be most wonderful. -
PLEASE HELP!!! My Macintosh HD volume disappeared
Ok, here's the deal...
I have a Powerbook 15" and I was trying to get it to recognize an HP printer because for some reason it didn't find the device.
So I wrote HP and they gave me some instructions wich I decided to follow (huge mistake!).
They included getting rid of some Preferences, some Caches and other things, and then to run the DISK UTILITY and do a REPAIR DISK PERMISSIONS.
I did all that but while in the Repair Disk Permissionas the computer froze for over an hour, so I performed a hard reset.
When the computer started again it didn´t find a Start up Volume.
I then started from the Tiger Installation CD, ran the Disk Utility from there...
and what is my surprise when I see that my hardrive appear but not my Macintosh HD Volume.
So...
I can´t do any repairing because the volume is not there
I can´t do a FireWire Transfer of Files because there´s no volume to connect
I can´t even Install again the System because there´s no destination volume
PLEASE SOMEBODY HELP!!!!
I´m desperate
Thanks in advance to all,
n.Hi naxpal and welcome to Apple Discussions,
As I was reading through your post I was noticing that I also had a problem similar to that about a month ago. The only thing different is that my Macintosh HD was there (where the OS was installed), but my second partition volume disappeared. I was wondering when it happened if my data was gone for ever, but it took me a few days to figure out what to do:
1) In your case, start up from your Tiger Installation CD.
2) Open Disk Utility and look in the list on the left for Macintosh HD.
3) If it is in the list, select it, and click Mount.
4) Quit Disk Utility.
5) Restart your PowerBook G4 holding the option key.
6) If Macintosh HD is available, select it and press the arrow on the right.
7) If you got to this step, you are all set and all you have to do is eject your Tiger Installation CD.
I hope this helps you.
-Jason -
I have installed bootcamp by the bootcamp assistant and worked properly.
Then I have partitioned the OS X 10.8.2 and installed another Mountain Lion System and I have got two MAC boot options and Bootcamp disappeared from the Option menu. However, Bootcamp still remained in the Startup Disk in the System Preferences. When I tried to boot Bootcamp using the Startup Disk it did not boot and received a message that there is no bootable device. I have not lost any data and can read Bootcamp partition from both OS X systems. Please advise how can I boot Windows / Bootcamp again? Thank you.Recommendation 1: Use a VM for this. It's essentially a giant C.F. to do this with native booting, and is potentially fragile.
But if you're going to ignore that and do this anyway, realizing that it can break anytime in particular with OS upgrades, and that it's very difficult to impossible to resize the three volumes once you've installed the systems:
1. create three partitions, setting each to be the size for OS X copy 1, copy 2, and Windows respectively. The Windows partition needs to be set to MS-DOS format (actually FAT32) which later in the Windows installer you'll reformat as NTFS. Do not use Boot Camp Assistant to resize/partition the disk, it simply won't work for this use case.
2. install OS X copy 1
3. install OS X copy 3
4. Use gdisk (available at sourceforge) which is a command line only application, to create a new hybrid MBR adding only the last partition (Windows) to the hybrid MBR and setting it to be bootable. As a concequence you will not be able to see/share either OS X volume from within Windows. The Windows NTFS volume will be visible from within OS X.
5. Install Windows to the only partition its installer should see (confirm size), you'll need to format it NTFS first, and I suggest using the fast format option if available. -
Gspeed ES Pro RAID keeps disappearing from Mac, have to re-initialize!
UPDATED VERSION:
MAC PRO KEEPS LOSING CONNECTION TO RAID DRIVE.
After 9 months of organizing a documentary film edit on an external RAID drive (12TB, Raid 0. Yes, I have 2 layers of backup), I purchased the PNY Nvidia Quadro 4000 video card for the primary edit. Soon after, I began having boot up issues. The screen would freeze at various points during the startup process, requiring manual power-downs.
Over the past two months, my computer has lost communication with the RAID 3 times, forcing me to rebuild it from my backup drives (10TB). One tech at Diskwarrior said my computer lost the partition, and that the 1s and 0s had been largely replaced with gibberish.
The Raid becomes unrecognized by my computer in one of two ways:
1- After two days of copying data back over to the raid (rebuilding it), I get an error code -36, saying a file cannot be read or written, then the Raid partition disappears from disk utility and the next time I start up the computer says it doesn’t recognize my drive. The ATTO configuration tool (the card that attaches my raid to the computer) sees the drive, but my computer does not. I have to re-initialize it and start over again.
2- The Raid will go from being recognized to not being recognized when I reboot one day. Again, I have to re-initialize and rebuild.
I removed the PNY Graphics card and put in the stock ATI Radeon HD 5770 it came with. On day 2 of rebuilding the RAID, I got the error -36 and the Raid disappeared from disk utility again. When I opened the raid folder, which seconds before had 10 TB of data on it, it read as zero items. So the PNY Nvidia card was NOT the problem.
Apple has worked on the computer 3 times, running extensive hardware tests, but the same problem persists. At one point they said my blackmagic card was the problem, and more recently they said I probably have bad ram. I tried separate ram (the old 6GB my computer came with), and my computer seemed to begin booting up okay, but one day later I had the -36 error, the RAID couldn’t be recognized again and I lost the data during another rebuild. Apple even replaced the Ram Tray, but the same problem persists.
G technology says my RAID’s hardware is fine, and ATTO, who makes the Raid card, says it looks fine to them too. This does not mean they are 100% not the problem though.
Yesterday as I was attempting to rebuild the RAID again, I saw the -36 error come up, and files stopped copying. I immediately made a screenshot and noted the time.
Today I spoke with a really cool tech at Apple named Ron who helped me investigate the Kernel log, and this is what it said (the RAID is called FadingWest):
Dec 6 17:05:36 Jesses-Mac-Pro kernel[0]: hfs_swap_BTNode: invalid forward link (0xbb739311 >= 0x0000df00)
Dec 6 17:05:36 Jesses-Mac-Pro kernel[0]: hfs: node=2717 fileID=4 volume=FadingWest device=/dev/disk3s2
Dec 6 17:05:36 Jesses-Mac-Pro kernel[0]: hfs: Runtime corruption detected on FadingWest, fsck will be forced on next mount.
Ron believes my problem is with the RAID card. He thinks it’s dropping the connection. So I’ve got an RMA going with ATTO for a new one.
Here are the final things I can troubleshoot at this point:
New RAID card (ATTO)
New RAID drive (G-Technology)
Motherboard / PCI lanes (Apple).
NEW COMPUTER (Apple)
Any ideas are appreciated. Here are the items in question:
Mac Pro mid 2010 2x2.66 Ghz 6 core Intel Xeon OS X Lion 10.7.5
G speed ES Pro (G Technology) – 12TB @ RAID 0
ATTO R680 RAID cardI found this on another help site, I think it's the trick:
there are 2 halves to the Dock. With a bar in the middle.
on the left side, there are 2 sections. the furthest left are the icons that will stay in the dock, then on the right side of the left half of the dock, are the temporary icons, the ones that just stay there till the program is done.
You can freely move a temporary icon to the left and it will be come a permanent icon.
I am reminded of the wizard of OZ here... you could always get to firefox... you just had to click your mouse (and drag an icon).. -
How to check DFS replication status in windows 2008 r2 file server
Hi,
I have created File server DFS namespace between 2 windows 2008 R2 server. namespace mode is 2008. I have copied 3 TB data on file server 1. now it is getting replicated from file server 1 to file server 2. till now the data is not fully replicated.
My question is how can I check the status of DFS replication? how will I come to know that the initial replication is completed.Scorpio. Yes you are right. Microsoft officially says it will not work. My apologies. Thanks for the correction.
Do Ultrasound and Sonar work with DFS Replication?
No. DFS Replication has its own set of monitoring and diagnostics tools. Ultrasound and Sonar are only capable of monitoring FRS.
Is there a way to know the state of replication?
Yes. There are a number of ways to monitor replication:
DFS Replication has a management pack for System Center Operations Manager 2007 that provides proactive monitoring.
DFS Replication has an in-box diagnostic report for the replication backlog, replication efficiency, and the number of files and folders in a given replication group.
Dfsrdiag.exe is a command-line tool that can generate a backlog count or trigger a propagation test. Both show the state of replication. Propagation shows you if files are being replicated to all nodes. Backlog shows you how many files still need to replicate
before two computers are in sync. The backlog count is the number of updates that a replication group member has not processed. On computers running Windows Server 2008 R2, Dfsrdiag.exe can also display the updates that DFS Replication is currently
replicating.
Scripts can use WMI to collect backlog information—manually or through MOM.
Miguel Fra /
Falcon IT Services
Computer & Network Support, Miami, FL
Visit our Knowledgebase and Support Sharepoint Site -
Why does my external drive disappear from my desktop?
I am switching from PC to Mac. I have 2 externaldrives. Both have been formatted in FAT 32 by the MAC. When I plug them in the desktop and finder see them, then with both of them they have disappeared from the desktop and from finder. Still can be seen in disk utility and system profiler. How can I find them and why does this happen?
If you daisy chained then try without. May not be enough power to handle both at sme time. Other than that read some info:
1. Shut-down your Mac, and unplug the power cord
2. Turn the power off on your external FireWire devices
3. Unplug the FireWire devices from the Mac
4. Wait for 5 min.
5. Plug the power cord to your Mac only
6. For PPC Macs: Restart the Mac while holding the Option-Apple-O-F, and keep holding until you get the ">" prompt, then release the keys
7. At the ">" prompt type:
reset-nvram and hit the Return key
set-defaults and hit the Return key
reset-all and hit the Return key
the last command will restart your mac
8. Shut down your Mac
9. Connect all your FireWire devices to the Mac and turn them on
10. Restart your Mac.
All your FireWire devices should reapear, if not repeat the procedure
How to avoid the issue :
The only really proven way to avoid burning up a FireWire port is to connect all devices and to turn them on PRIOR turning on the Mac. Likely, one must unplug them and turn them off AFTER the Mac has been turned off. If you need to connect another device, then you're on for a shutdown of your machine... It's a tad annoying but it guarantees that the FW ports won't be damaged. Be careful when using self powered devices such as webcams, iPods, hard drives or hubs, as they can destroy the port pretty easily. Another thing is to avoid daisy-chaining hard drives.
When the FW port doesn't respond anymore :
In this case, peripherals won't be mounted upon plugging, and won't be displayed in Apple's System Profiler. The self powered devices will still be fed by the port, but won't respond either. It happens that the PHY just hangs after a surge or a random problem. Once hung, the port will not respond any longer, it is possible to reset the component by going through the following steps :
1° boot the PPC mac in Open Firmware by holding [ Apple key - Option - O - F ] after the startup chime. 2° you'll get to a command prompt. the keyboard mapping will be QWERTY, so pay attention when you type the following : RESET-NVRAM (enter) RESET-ALL (enter) 3° Now the mac should restart itself and the port should function properly again. If it still doesn't work, then it means that the PHY is damaged.
http://www.hardmac.com/articles/16/
From Kappy post:
922 is only used in dual drive cases to provide a "build-in firmware RAID support"
912 or 912+ is FW800, the "+" means USB2
911 is FW400
924 adds eSATA support along with FW400/800
MacSales, OWC Tech Support library is where I would go first, as they do tend to have or links to, firmware updates for Oxford.
From Wiebetech:
I just upgraded my Mac OS, and now I'm having trouble with my FireWire device. What can I do?
A: With nearly every OS update Apple releases, some external drives are not recognized after the update. The typical symptom is that the device will not mount but the volume is visible and grayed out in Disk Utility. This means that the device is working properly, but the OS does not recognize the volume as mountable. Sometimes the drive does not show up at all.
The first thing to do is to see if repairing Permissions with Apple's Disk Utility First Aid feature solves the problem. If not, try repairing the disk with First Aid. Another possible solution is to zap the PRAM. This is done with a keyboard command while rebooting. Restart your computer and hold down the Command, Option, P and R keys. Consult the Apple web site for details.
If this does not work, then try pushing the PMMU reset button on the logic board. Consult the Apple web site for locations of the button for your Mac. If the drive still does not show up, shut down, disconnect all peripheral devices, and boot from the Mac OS Installation CD. The later the OS version, the better. Do not reinstall the OS, but when the Installer is loaded up and ready to begin, go to the File menu and use the Disk Utility program. Connect the drive that is having problems, then start the Disk Utility application. If you see the external drive and it is not grayed out, you know the drive is okay. Run Disk First Aid on it anyway. Then run it on your internal boot drive while you are at it. When done, unmount the external drive and UNPLUG it! Then restart the Mac.
When the Mac has restarted and is running on the internal boot drive, reconnect the external drive.
Maybe you are looking for
-
HI gurus, I have fixed the exchange rate as 40 (say) in the PO header. Now when I do Migo after miro, it throws the following error; Enter rate USD / INR rate type B for 06.09.2007 in the system settings Message no. SG105 Diagnosis :For the conversi
-
Performance problem in application
Hi , I have some serious problems with my application on perfromance, when i check the db for events i can see the following Events Total_Waits Time Wauted 1 Data file init write 1794 9077 2 local write wait 24 63 3 read b
-
How to use on board counter to change sample rate dynamically on pci-6134
Hi, I am relatively new in LabView. I am making power quality measurement system and I need to vary the sampling rate of my pci-6134 dynamically (all channels simultaneously). What I need is to have a constant amount of samples in each period of meas
-
Ensure 1 Active Sync process runs against the change log before all others?
He folks, We have a lot of LDAP active sync thread. We have a primary on that correlates to an individuals account. Then we have several that represent affiliations at our organization. The affiliations are represented in LDAP as subordinates of the
-
SCREEN - INPUT = '0' i.e.Dis-abling input field in Selection screen????
Hi Experts, I hv a selection screen with, 1)SELECT-OPTIONS: input_fld_1 with domain value range of A, B, C, D, E, F 2)input_fld_2 3)PARAMETERS: input_fld_3 has the LIST BOX So, my requirement is, If the user selects/enters A, B, C, D in input_fld_1,