VPC between server and nexus switches

Hi all,
I would like to ask following question:
We are using virtual portchannels to connect e.g. ESXi-Servers with trunks on two Nexus switches. When the switch "rz2sw1" has gone faulty, we expect that the trunk connections between switch rz2sw2  would still work. That's the reason why they are built. But they didn't as you can see in the screenshot (attaced) former mail.
Do you know what can be problem.. thank you

It appears that the peer-link was down.  If the peer-link is down and the keep-alive is still up, the secondary device will shutdown all of it's VPC links to ensure dual active (split brain) is avoided.
On a Nexus 7000, its recommended to use a front panel (data port) for the keep-alive instead of the management port.  My assumption would be that you are using the MGMT0 for keep-alive and all front panel ports went off-line.  If you use a front panel port for keep-alive and all line cards go off line on the primary, the secondary will take over as expected.

Similar Messages

  • Is it possible to Configure VPC Between N5010 and 6513

    Hello Gents,
    Please let me know if we can  configure VPC Between N5010 and 6513(coreswitch).
    IF Yes, Does it have any loops or abnormal traiffc behaviour ?
    Please refer the attached mail for current network diagram
    1) I would like to establish VPC Between N5010 and Cisco 6513 switch
    2) if yes, Does the upstream devices above 6513 core switch will forward the traffic from all the
    6513 ports connected to N5000 ports or 6513 will send traffic from one up link and block other
    uplink ports as part of STP.
    3) Is VSS on 6513 is required for Point #1
    Please refer some links on this as well.
    Appreciate your quick response.
    Thanks and Regards,
    KA.

    Hi Karim ,
    You can use this one - you can consider your 6k the FEX as in this example
    http://www.cisco.com/en/US/prod/collateral/switches/ps9441/ps9670/configuration_guide_c07-543563.html
    On the portchannel to 6k will not configure :
    "switchport mode fex-fabric"
    "fex associate 100"
    This configuration in indended to be used with FEX.
    Regards
    Dan

  • Data streaming between server and client does not complete

    Using an ad-hoc app, data streaming between server
    and client does not complete as it supposed to be.
    The process runs well in solaris 5.8, however under 5.9
    we have found the characters stream buffer length limitation
    is around 900 to 950 characters (by default we are using 3072
    characters).
    Example:
    - We are transfering HTML file, which will be displayed
    in the App client, with buffer=3072, the HTML only displayed / transfered
    as xxxxxxxx characters, but with buffer=900 the HTML is displayed properly,
    in this case, the only problem that we have is the file transfer will
    eventually longer than usual.
    - There is another case, where we have to transfer information (data) as stream
    to the client. A long data stream will not appear at all in the client.
    Any ideas why the change between 5.8 and 5.9 woudl cause problems?
    The current app-driver that we are using is compiled using Solaris 5.6,
    if possible we would like to have use of a later version, which is compiled using Solaris 5.9, do you think this will probably solve our problem?
    Thanks
    Paul

    Does this have anything to do with Java RMI? or with Java come to think of it?

  • Serialize the object between Server and Client?

    Hello friends,
    What is the important to Serialize the object between server and client?
    Thanks
    tamilvanan

    in which context ??
    Anyways,checkout the below link and try to understand how do we convert Serializable Object's State to in Stream and send it over network.
    http://java.sun.com/j2se/1.4.2/docs/guide/serialization/examples/index.html
    Hope that might help :)
    REGARDS,
    RaHuL

  • Bandwidth between server and client

    HI
    What is the minimum bandwidth can be allocated between server and client?

    Hi,
    Your question has no standard answer. The minimum bandwidth is variable to each specific system. It depends on many other factors too.
    Thanks,
    Gordon

  • Speed between server and client when using FML

    I using FML between server and client, the server access oracle using only 5 ms, but when tranfer back to client, it about 100ms long. I tuned my hp-ux 11 kernel and tuxedo config file, but useless, Why?

    Hi Tumecan,
    Your expected information available here, check.
    Frontend Network Load - Network Integration Guide (BC-NET) - SAP Library
    few related SAP Notes:
    164102 - Network load between application server and front end
    500235 - Network Diagnosis with NIPING
    62418 - Network Load of SAPGUI Frontend Communication
    679918 - The front-end network time
    578118 - Long response times on the SAP GUI
    161053 - Using SAP GUI in WAN
    Regards,
    V Srinivasan

  • Running HSRP between N5k 's and vPC between N2k and server

    Dear All,
    I have the following existing setup, i would like to run HSRP between N5k1 and N5k2. Also would lilke to run vPC between N2k1,N2k2 to the server farm which are dual homed. Please find the diagram attached.
    Please advise the step by step process along with the commands to be entered. Thanks for your help

    Hi,
    If you don't have many vlans, there is no need to load balance.  Make one of the 5ks the primary for HSRP and the other one stand-by.
    here is good link on how to configure it.  Make sure to run HSRP version 2. This way you can mach the HSRP group IDs with your vlan IDs. Also give a higher priority to the active 5k and enable preemption.
    http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5500/sw/unicast/7_x/cisco_n5500_layer3_ucast_cfg_rel_6x/l3_hsrp.html
    HTH

  • Screen sharing between server and iMac appears to connect but no window opens

    We have been trying to screen share between a server and iMac. Both are running Snow Leopard 10.6.7. It seems like we connect using the share screen app because we don't get any error messages after inputing the username and password but no window opens for the server we are connected to. When I look under the windows tab I can see a checkmark next to our server name and trying 'bring all to front' doesn't do anything. The video card on the server died and was removed by our tech support who said we could still access the computer via screen sharing. Would the server not having a video card be the cause of our problem?
    Thanks.

    Hi,
    A Bit for other reading this thread.
    To change the Login port for any AIM based name you have to obviously Log out first and then Change the port (SSL might need to be selected first) and then Press Enter to "Set" the port.
    This use of the Enter key is the bit that is different to earlier versions of iChat.
    For Gary,
    Which Thomson-Alcatel device do you have ?
    Thomson-Alcatel Speedtouches used to work well when the firmware that ran them was at Version 4.2.5 or less.
    At least at this level you could access the device via Terminal using Telnet and then access the Command Line Interface (CLI) and "Unbind" SIP from port 5060
    Later versions of their Firmware did not allow for a full Unbind of SIP and Video and Audio chats could only be partially successful (about 15 buddies out a list of 50
    Of course using UPnP to open ports for iChat 4 helps with the Screen Sharing as the process is an Screen Share with an Audio Chat along side and both have to work/connect.
    I am surprised to hear that in iChat 5 that Screen Sharing is not working when Video and Audio chats are.
    For this reason I would ask how the ports have been opened in the Thomson device ?
    After that I would keen to know if the Thomson Device or the Time Capsule is doing DHCP to the LAN ?
    (Share an IP on the Time capsule is to Enable DHCP)
    I am not sure how AT&T expect anyone to use their site to gain help or see what they currently offer when you have to type in a phone number or area (ZIP code).
    I did enter the example number and got to this set of pages http://www.att.com/esupport/main.jsp?cv=801#
    I see no reference to any Thomson-Alcatel device.
    8:15 PM Monday; February 15, 2010
    Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"

  • Time sync between server and client

    Hi guys,
    I have written a chess server and client. My next step is to implement a clock which will be used in timed games, however, I am not sure of the best solution. I can't think of a reliable method to keep the client's time in sync with the servers because the event latency varies between individual events and clients.
    My first idea was to send a 'tick' event every second but I dont think this the best solution. I have seen many applet based clients which have timers, such as Yahoo chess.
    I know this question is a little vague, I can give more detail if needed.
    Thanks,
    Alex

    To prevent client-side cheating, the server should keep the
    "official" clock. Every so often (perhaps when a move gets made?),
    notify both clients of the official time. Clients count seconds from
    that official time.
    This is a suboptimal solution because it leaves clients vulnerable
    to network lag. I can't think of any other solution that doesn't give
    clients some responsibility for tracking time, though, and that's a
    big security hole.
    If you're willing to open that hole, have each client report back to
    the server the elapsed local time from when they recieved the
    last move to when they made their move. Then update the other
    client's clock accordingly.

  • Link aggregated between NAS and a switch: the Mac as a very slow access...

    Hello,
    in my Office we're working with Macs and PCs and all the data is on a NAS.
    Here is our configuration:
    NAS <-link1->Switch<-Link2->Macs or PC.
    Macs are connected with AFP protocol (because SMB is very slow).
    We want to use Link Aggregation between the NAS and the switch (with 802.3ad procotol) but when we do that all the Macs have a very slow access to the NAS. But all is OK with the PCs.
    What can we do? Is there a problem with macOS X and link aggregation?
    Thank you for your help.
    Nicolas

    Sorry, not sure what the question is exactly.
    You must have an Xserve, or Ethernet cards capable of Jumbo Frames for one, I assume the Switch & NAS are capable?
    Possible clues...
    http://docs.info.apple.com/article.html?path=ServerAdmin/10.4/en/c3ha3.html
    http://discussions.apple.com/thread.jspa?threadID=1715388&tstart=0
    http://www.macnn.com/articles/04/06/21/link.aggregation.for.macs/
    http://www.smallnetbuilder.com/content/view/30556/53/
    http://www.afp548.com/forum/viewtopic.php?showtopic=8309

  • Capture http traffic between server and proxy

    Hi,
    I am not a solaris admin so I need some help to capture http traffic between proxy and server.
    I used 'snoop port 80' on my proxy server but this command gives me the traffic between client and proxy.
    PS: i do not have access to remote server.
    Thanks
    Linda

    You probably need this instead:
    snoop host server
    where server is the hostname of the server that you are trying to connect to.
    If you have multiple interfaces, you have to be sure you are snooping on the right interface.

  • Remote span between Extreme and Cisco switches

    Hello,
    I need to configure remote span between Extreme Networks X460-24p and Cisco Cataylst 2960X switches. 2 IP phones are connected to ports 15 and 17 on Extreme switch, and should be monitored to port 1/0/47 on Cisco switch. Extreme and Cisco switches are interconnected with trunk (port 28 on Extreme with port 1/0/51 on Cisco).
    I configured the following:
    On Extreme switch:
    configure mirror mode enhanced
    enable mirroring to port 28 remote-tag 1000
    configure mirroring add port 17 ingress-and-egress
    configure mirroring add port 15 ingress-and-egress
    On Cisco switch:
    vlan 1000
     name RemoteSPAN
     remote-span
    monitor session 1 destination interface Gi1/0/47
    monitor session 1 source remote vlan 1000
    But this is not working :(
    Does enyone have experience with this? I really need help to make this work.
    Thanks.

    OK, this configuration is actually working :)

  • Adapter-fex Supported VICs and Nexus Switches

    HI,
    I am thinking of using C220M4 in standalone mode. I have been reading about adapter-fex and I am wondering which Cisco VIC supports adapter-fex and which Nexus Switch will support adapter-fex.
    I am thinking of using a VIC1225 and Nexus 3000.
    Thanks.

    I believe that adaptor fex is supported only with Nexus 5k and N2k:
    Network Adapter Virtualization Design (Adapter-FEX) with Cisco Nexus 5500 Switches and Cisco Nexus 2232 Fabric Extenders
    http://www.cisco.com/c/en/us/products/collateral/switches/nexus-5000-series-switches/guide_c07-690080.html
    http://www.cisco.com/c/en/us/products/collateral/switches/nexus-5000-series-switches/data_sheet_c78-657397.html

  • Move mailboxes between server and computer

    Somehow my mailboxes have become scrambled beween those on the server and those on my computer.  Can I restore the original storage?
    Lelteto

    Hi,
    In your case, please make sure that the Migration.8f3e7716-2011-43e4-96b1-aba62d229136 mailbox exists by running the following cmdlet.
    Get-Mailbox -Arbitration |fl name,alias
    In my last reply, I recommend you check if there is any related error or warning in Application log in Event Viewer.
    Also, you can export your mailboxes into pst files and then import these pst files.
    Hope my clarification is helpful.
    Best regards,
    If you have feedback for TechNet Subscriber Support, contact
    [email protected]
    Amy Wang
    TechNet Community Support

  • Dental office management software cannot share between server and workstation

    The wsetup files that are located in c:\softdent on the server are not visible on the workstation and the installation will not run until this is resolved.
    The map drive (z: ) doesn’t show the files that are located on the server. The file that should be in z:\setup (folder called wsetupfiles ) does not exist but is live on the server.
    The permissions on the server or WS are incorrect.
    What can be done.

    Hi,
    Could you let us know what's the management software? Were your Server and client all Windows system?
    If yes, what's the version of them?
    Could you ping Server from client either via IP address or Server name?
    This article could be used to troubleshoot:
    Find PCs,  devices, and content on your network
    http://windows.microsoft.com/en-in/windows-8/find-pcs-devices-content-on-network
    Karen Hu
    TechNet Community Support

Maybe you are looking for

  • Using null value of item

    Hi All, I use this part-of-code in pl/sql statement in a 'where' clause in order to filter records to those that took place between some hours range: ..... and to_char(STARTDATE,'HH24:MI:SS') between NVL(:P3_HOURS_FROM,'00:00:00') and NVL(:P3_HOURS_T

  • Video Not Viewable from Jabber Client To SX20

    Good morning, We are testing out the jabber for Windows client and the only way that we can get it to connect is by forcing the H323 protocol (ie:H323:[email protected]) and initiating from the SX20.  When we do this, we can only see and hear what is

  • Nvarchar Columns are not imported into OWB 10g

    Hi Team, I am quite new to Oracle BI(Just 2 weeks old) environment. I have completly gone through oralce wharehouse builder user's guide. I am trying to setup a datamart in which data will be pulled from MS SQL server 2008. Here is my Problem 1. Setu

  • Is there anywhere I can download acrobat 9 standard?

    Is there anywhere I can go to download Acrobat 9 Standard? I see Professional in the Adobe website but not Standard. Thank you in advance

  • Country name want to mention in process order

    Hi, ABC  is a FERT material. I want to create process order country wise, since I have world wise business. During creation of process order I want to mention country name for which process order is being created. For this, I want to make a configura