VPN and racoon in foreground

I have set up racoon to work with my VPN at work. Therefore I had to modify racoon.conf.
Everything works well, as long as I run racoon in foreground (racoon -F). As soon as racoon is run background connections cannot be established using the Mac OS X VPN Gui.
Has any of you encountered this problem? Are there solutions to circumvent this behaviour?
Thank you very much,
Stephan
Macbook Mac OS X (10.4.7)

The second one seems an interesting solution. The only thing is that I was planning to connect the clients to a switch and this s
witch to the core router. And then use vlans and subinterfaces to connect all the clients to 1 physical interface in th
e core router. But I think your solution might work. Im going to think about it.
Thanks a lot for your help.
Regards,
Daniel
I've already tried your idea. Works really well. Thanks a lot.

Similar Messages

IpSec VPN and NAT don't work togheter on HP MSR 20 20

Hi People,
I'm getting several issues, let me explain:
I have a Router HP MSR with 2 ethernet interfaces, Eth 0/0 - WAN (186.177.159.98) and Eth 0/1 LAN (192.168.100.0 /24). I have configured a VPN site to site thru the internet, and it works really well. The other site has the subnet 10.10.10.0 and i can reache the network thru the VPN Ipsec. The issue is that the network 192.168.100.0 /24 needs to reach internet with the same public address, so I have set a basic NT configuration, when I put the nat configuration into Eth 0/0 all network 192.168.100.0 can go to internet, but the VPN goes down, when I remove the NAT from Eth 0/0 the VPN goes Up, but the network 192.168.100.0 Can't go to internet.
I'm missing something but i don't know what it is !!!!, See below the configuration.
Can anyone help me qith that, I need to send te traffic with target 10.10.10.0 thru the VPN, and all other traffic to internet, Basically I need that NAT and VPN work fine at same time.
Note: I just have only One public Ip address.
version 5.20, Release 2207P41, Standard
sysname HP
nat address-group 1 186.177.159.93 186.177.159.93
domain default enable system
dns proxy enable
telnet server enable
dar p2p signature-file cfa0:/p2p_default.mtd
port-security enable
acl number 2001
rule 0 permit source 192.168.100.0 0.0.0.255
rule 5 deny
acl number 3000
rule 0 permit ip source 192.168.100.0 0.0.0.255 destination 10.10.10.0 0.0.0.255
vlan 1
domain system
access-limit disable
state active
idle-cut disable
self-service-url disable
ike proposal 1
encryption-algorithm 3des-cbc
dh group2
ike proposal 10
encryption-algorithm 3des-cbc
dh group2
ike peer vpn-test
proposal 1
pre-shared-key cipher wrWR2LZofLx6g26QyYjqBQ==
remote-address <Public Ip from VPN Peer>
local-address 186.177.159.93
nat traversal
ipsec proposal vpn-test
esp authentication-algorithm sha1
esp encryption-algorithm 3des
ipsec policy vpntest 30 isakmp
connection-name vpntest.30
security acl 3000
pfs dh-group2
ike-peer vpn-test
proposal vpn-test
dhcp server ip-pool vlan1 extended
network mask 255.255.255.0
user-group system
group-attribute allow-guest
local-user admin
password cipher .]@USE=B,53Q=^Q`MAF4<1!!
authorization-attribute level 3
service-type telnet
service-type web
cwmp
undo cwmp enable
interface Aux0
async mode flow
link-protocol ppp
interface Cellular0/0
async mode protocol
link-protocol ppp
interface Ethernet0/0
port link-mode route
nat outbound 2001 address-group 1
nat server 1 protocol tcp global current-interface 3389 inside 192.168.100.20 3389
ip address dhcp-alloc
ipsec policy vpntest
interface Ethernet0/1
port link-mode route
ip address 192.168.100.1 255.255.255.0
interface NULL0
interface Vlan-interface1
undo dhcp select server global-pool
dhcp server apply ip-pool vlan1

ewaller wrote:
What is under the switches tab?
Oh -- By the way, that picture is over the size limit defined in the forum rules in tems of pixels, but the file size is okay. I'll let it slide. Watch the bumping as well.
If you want to post the switches tab, upload it to someplace like http://img3.imageshack.us/, copy the thumbnail (which has the link to the original) back here, and you are golden.
I had a bear of a time getting the microphone working on my HP DV4, but it does work. I'll look at the set up when I get home tonight [USA-PDT].
Sorry for the picture and the "bumping"... I have asked in irc in arch and alsa channels and no luck yet... one guy from alsa said I had to wait for the alsa-driver-1.0.24 package (currently I have alsa-driver-1.0.23) but it is weird because the microphone worked some months ago...
So here is what it is under the switches tab

Cisco ASA Site to Site IPSEC VPN and NAT question

Hi Folks,
I have a question regarding both Site to Site IPSEC VPN and NAT. Basically what I want to achieve is to do the following:
ASA2 is at HQ and ASA1 is a remote site. I have no problem setting up a static static Site to Site IPSEC VPN between sites. Hosts residing at 10.1.0.0/16 are able to communicate with hosts at 192.168.1.0/24, but what i want is to setup NAT with IPSEC VPN so that host at 10.1.0.0/16 will communicate with hosts at 192.168.1.0/24 with translated addresses
Just an example:
Host N2 (10.1.0.1/16) will communicate with host N1 192.168.1.5 with destination lets say 10.23.1.5 not 192.168.1.5 (Notice the last octet should be the same in this case .5)
The same translation for the rest of the communication (Host N2 pings host N3 destination ip 10.23.1.6 not 192.168.1.6. again last octet is the same)
It sounds a bit confusing for me but i have seen this type of setup before when I worked for managed service provider where we had connection to our clients (Site to Site Ipsec VPN with NAT, not sure how it was setup)
Basically we were communicating with client hosts over site to site VPN but their real addresses were hidden and we were using translated address as mentioned above 10.23.1.0/24 instead of (real) 192.168.1.0/24, last octet should be the same.
Appreciate if someone can shed some light on it.

Hi,
Ok so were going with the older NAT configuration format
To me it seems you could do the following:
Configure the ASA1 with Static Policy NAT
access-list L2LVPN-POLICYNAT permit ip 192.168.1.0 255.255.255.0 10.1.0.0 255.255.0.0
static (inside,outside) 10.23.1.0 access-list L2LVPN-POLICYNAT
Because the above is a Static Policy NAT it means that the translation will only be done when the destination network is 10.1.0.0/16
If you for example have a basic PAT configuration for inside -> outside traffic, the above NAT configuration and the actual PAT configuration wont interfere with eachother
On ASA2 side you can normally configure NAT0 / NAT Exemption for the 10.1.0.0/16 network
access-list INSIDE-NONAT remark L2LVPN NONAT
access-list INSIDE-NONAT permit ip 10.1.0.0 255.255.0.0 10.23.1.0 255.255.255.0
nat (inside) 0 access-list INSIDE-NONAT
You will have to take into consideration that your access-list defining the L2L-VPN encrypted traffic must reflect the new NAT network
ASA1: access-list L2LVPN-ENCRYPTIONDOMAIN permit ip 10.23.1.0 255.255.255.0 10.1.0.0 255.255.0.0
ASA2: access-list L2LVPN-ENCRYPTIONDOMAIN permit ip 10.1.0.0 255.255.0.0 10.23.1.0 255.255.255.0
I could test this setup tomorrow at work but let me know if it works out.
Please rate if it was helpful
- Jouni

Works windows mobile with SSL VPN and anyconnect

Hello,
do anyone know if the following OS works with ASA 8.x SSL VPN client ,SSL clientless VPN and anyconnect client and Secure Desktop :
windows mobile 5.0 Premium phone edition
windows mobile 6.0
windows embedded CE,Net
windows mobile 2003
Thank you for your help
Michael

[url=http://fztodds.24fast.info/washington225.html] washington [/url]
[url=http://fztodds.24fast.info/washington16e.html] washington [/url]
[url=http://fztodds.24fast.info/washingtond66.html] washington [/url]
[url=http://fztodds.24fast.info/washington4e0.html] washington [/url]
[url=http://fztodds.24fast.info/washington00b.html] washington [/url]
[url=http://fztodds.24fast.info/washington1e7.html] washington [/url]
[url=http://ioinlfu.zotzoo.com/washington0a8.html] washington [/url]
[url=http://ioinlfu.zotzoo.com/washington9de.html] washington [/url]
[url=http://ioinlfu.zotzoo.com/washingtone4a.html] washington [/url]
[url=http://ioinlfu.zotzoo.com/washington4ec.html] washington [/url]
[url=http://ioinlfu.zotzoo.com/washington184.html] washington [/url]
[url=http://ioinlfu.zotzoo.com/washingtonb73.html] washington [/url]
[url=http://ioinlfu.zotzoo.com/washington853.html] washington [/url]
[url=http://ygkbfvp.wipou.com/washington1a5.html] washington [/url]
[url=http://ygkbfvp.wipou.com/washingtonde7.html] washington [/url]
[url=http://ygkbfvp.wipou.com/washington2b8.html] washington [/url]
[url=http://ygkbfvp.wipou.com/washington902.html] washington [/url]
[url=http://ygkbfvp.wipou.com/washingtonc99.html] washington [/url]
[url=http://ygkbfvp.wipou.com/washingtoncc7.html] washington [/url]
[url=http://ygkbfvp.wipou.com/washington598.html] washington [/url]
[url=http://yfldvbz.webheri.net/washingtonbe2.html] washington [/url]
[url=http://yfldvbz.webheri.net/washingtone9b.html] washington [/url]
[url=http://yfldvbz.webheri.net/washington4e0.html] washington [/url]
[url=http://yfldvbz.webheri.net/washington327.html] washington [/url]
[url=http://yfldvbz.webheri.net/washingtonada.html] washington [/url]
[url=http://yfldvbz.webheri.net/washingtond2b.html] washington [/url]
[url=http://yfldvbz.webheri.net/washington317.html] washington [/url]
[url=http://odwjneh.yourfreehosting.net/washington7cb.html] washington [/url]
[url=http://odwjneh.yourfreehosting.net/washingtoneaf.html] washington [/url]
[url=http://odwjneh.yourfreehosting.net/washington259.html] washington [/url]
[url=http://odwjneh.yourfreehosting.net/washington8e0.html] washington [/url]
[url=http://odwjneh.yourfreehosting.net/washingtonc03.html] washington [/url]
[url=http://odwjneh.yourfreehosting.net/washington092.html] washington [/url]
[url=http://odwjneh.yourfreehosting.net/washington79c.html] washington [/url]
[url=http://aeaukol.rack111.com/washington766.html] washington [/url]
[url=http://aeaukol.rack111.com/washingtona2e.html] washington [/url]
[url=http://aeaukol.rack111.com/washington4c4.html] washington [/url]
[url=http://aeaukol.rack111.com/washingtonb9f.html] washington [/url]
[url=http://aeaukol.rack111.com/washingtond3a.html] washington [/url]
[url=http://aeaukol.rack111.com/washington54a.html] washington [/url]
[url=http://aeaukol.rack111.com/washington777.html] washington [/url]
[url=http://uhbayoe.hostrator.com/washington300.html] washington [/url]
[url=http://uhbayoe.hostrator.com/washington239.html] washington [/url]
[url=http://uhbayoe.hostrator.com/washington7b4.html] washington [/url]
[url=http://uhbayoe.hostrator.com/washingtonad5.html] washington [/url]
[url=http://uhbayoe.hostrator.com/washingtone03.html] washington [/url]
[url=http://uhbayoe.hostrator.com/washington399.html] washington [/url]
[url=http://uhbayoe.hostrator.com/washington9e9.html] washington [/url]
[url=http://ggaubio.hostevo.com/washington878.html] washington [/url]
[url=http://ggaubio.hostevo.com/washington525.html] washington [/url]

Clientless SSL VPN and ActiveX question

Hey All,
First post for me here, so be gentle. I'll try to be as detailed as possible.
With the vast majority of my customers, I am able to configure an IPSEC L2L VPN, and narrow the traffic down to a very minimal set of ports. However, I have a customer that does not want to allow a L2L VPN tunnel between their remote site, and their NOC center. I thought this might be a good opportunity to get a clientless (they don't want to have to launch and log into a separate client) SSL VPN session setup. Ultimately, this will be 8 individual sites, so setting up SSL VPN's at each site would be cost prohibitive from a licensing perspective. My focus has been on using my 5510 (v8.2(5)) at my corp site as the centralized portal entrance, and creating bookmarks to each of the other respective sites, since I already have existing IPSEC VPN's via ASA5505, (same rev as the 5510 )setup with each of the sites.
First issue I've run into is that I can only access bookmarks that point to the external address for the remote web-server (the site has a static entry mapping an external address to the internal address of the web server). I am unable to browse (via bookmark) to the internal address of the remote web server. Through my browser at the office, I can access the internal address fine, just not through the SSL VPN portal. I am testing this external connectivity using a cell card to be able to simulate outside access. Is accessing the external IP address by design, or do I have something hosed?
Second issue I face is when I access the external address through the bookmark, I am ultimately able to log onto my remote website, and do normal browsing and javascript-type functions. I am not able to use controls that require my company's ActiveX controls (video, primarily). I did enable ActiveX relay, and that did allow the browser to start prompting me to install the controls as expected, but that still didn't allow the video stream through. The stream only runs at about 5 fps, so it's not an intense stream.
I have researched hairpinning for this situation, and "believe" that I have the NAT properly defined - even going as far as doing an ANY ANY, just for testing purposes to no avail. I do see a decent number of "no translates" from a show nat:
match ip inside any outside any
NAT exempt
translate_hits = 8915, untranslate_hits = 6574
access-list nonat extended permit ip any any log notifications
access-list nonat extended permit ip 192.168.17.0 255.255.255.0 192.168.2.0 255.255.255.0
access-list nonat extended permit ip 192.168.16.32 255.255.255.224 192.168.2.0 255.255.255.0
access-list nonat extended permit ip 192.168.17.0 255.255.255.0 192.168.16.32 255.255.255.224
access-list nonat extended permit ip 192.168.16.32 255.255.255.224 192.168.17.0 255.255.255.0
access-list nonat extended permit ip 192.168.17.0 255.255.255.0 172.16.250.0 255.255.255.0
access-list nonat extended permit ip 192.168.16.32 255.255.255.224 172.16.250.0 255.255.255.0
access-list nonat extended permit ip 192.168.16.32 255.255.255.224 172.16.254.0 255.255.255.0
access-list nonat extended permit ip 192.168.17.0 255.255.255.0 172.16.254.0 255.255.255.0
access-list nonat extended permit ip 192.168.17.0 255.255.255.0 host A-172.16.9.34
access-list nonat extended permit ip 192.168.18.0 255.255.255.0 192.168.2.0 255.255.255.0
access-list nonat extended permit ip 192.168.18.0 255.255.255.0 192.168.16.32 255.255.255.224
access-list nonat extended permit ip 192.168.18.0 255.255.255.0 192.168.17.0 255.255.255.0
access-list nonat extended permit ip 192.168.18.0 255.255.255.0 172.16.250.0 255.255.255.0
access-list nonat extended permit ip 192.168.18.0 255.255.255.0 172.16.254.0 255.255.255.0
access-list nonat extended permit ip 192.168.18.0 255.255.255.0 host A-172.16.9.34
access-list nonat extended permit ip 192.168.17.0 255.255.255.0 192.168.18.0 255.255.255.0
access-list nonat extended permit ip 192.168.16.32 255.255.255.224 192.168.18.0 255.255.255.0
access-list nonat extended permit ip 192.168.16.32 255.255.255.224 host 172.16.62.57
access-list nonat extended permit ip 192.168.17.0 255.255.255.0 host 172.16.62.57
access-list nonat extended permit ip 192.168.18.0 255.255.255.0 host 172.16.62.57
access-list nonat extended permit ip 192.168.17.0 255.255.255.0 172.16.8.0 255.255.254.0
access-list nonat extended permit ip 192.168.16.32 255.255.255.224 172.16.8.0 255.255.254.0
access-list D_Traffic extended permit ip 192.168.16.32 255.255.255.224 192.168.2.0 255.255.255.0
access-list D_Traffic extended permit ip 192.168.16.32 255.255.255.224 192.168.17.0 255.255.255.0
access-list D_Traffic extended permit ip 192.168.16.32 255.255.255.224 192.168.18.0 255.255.255.0
access-list D_Traffic extended permit ip 192.168.16.32 255.255.255.224 172.16.250.0 255.255.255.0
access-list D_Traffic extended permit ip 192.168.17.0 255.255.255.0 192.168.2.0 255.255.255.0
access-list D_Traffic extended permit ip 192.168.17.0 255.255.255.0 192.168.16.32 255.255.255.224
access-list D_Traffic extended permit ip 192.168.17.0 255.255.255.0 192.168.18.0 255.255.255.0
access-list D_Traffic extended permit ip 192.168.18.0 255.255.255.0 192.168.2.0 255.255.255.0
access-list D_Traffic extended permit ip 192.168.18.0 255.255.255.0 192.168.16.32 255.255.255.224
access-list D_Traffic extended permit ip 192.168.18.0 255.255.255.0 192.168.17.0 255.255.255.0
access-list D_Traffic extended permit ip 192.168.18.0 255.255.255.0 172.16.250.0 255.255.255.0
access-list D_Traffic extended permit ip 192.168.17.0 255.255.255.0 172.16.250.0 255.255.255.0
access-list outside_1_cryptomap extended permit ip 192.168.16.32 255.255.255.224 host A-172.16.9.34
access-list outside_1_cryptomap extended permit ip 192.168.17.0 255.255.255.0 host A-172.16.9.34
access-list outside_1_cryptomap extended permit ip 192.168.18.0 255.255.255.0 host A-172.16.9.34
access-list outside_1_cryptomap extended permit ip 192.168.16.32 255.255.255.224 host 172.16.62.57
access-list outside_1_cryptomap extended permit ip 192.168.17.0 255.255.255.0 host 172.16.62.57
access-list outside_1_cryptomap extended permit ip 192.168.18.0 255.255.255.0 host 172.16.62.57
access-list External_VPN extended permit ip 192.168.16.32 255.255.255.224 172.16.254.0 255.255.255.0
access-list External_VPN extended permit ip 192.168.17.0 255.255.255.0 172.16.254.0 255.255.255.0
access-list outside_in extended permit icmp any any log notifications
access-list outside_in extended permit tcp any any log notifications
pager lines 24
logging enable
logging asdm informational
logging ftp-server 192.168.16.34 / syslog *****
mtu inside 1500
mtu outside 1500
ip local pool Remote 172.16.254.1-172.16.254.25 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-645.bin
no asdm history enable
arp timeout 14400
global (inside) 1 interface
global (outside) 1 interface
nat (inside) 0 access-list nonat
nat (inside) 1 192.168.16.32 255.255.255.224
nat (inside) 1 192.168.17.0 255.255.255.0
nat (inside) 1 0.0.0.0 0.0.0.0
access-group outside_in in interface outside
192.168.2.0 is my corp network range
192.168.2.171 is my internal IP for corp ASA5510
97.x.x.x is the external interface for my corp ASA5510
192.168.16.34 is the internal interface for the remote ASA5505
64.x.x.x is the external interface for the remote ASA5505
192.168.17.0, and 192.168.18.0 are two other private LANS behind the remote 5505
As you can see, I have things reasonably wide open - with no port restrictions on this one yet - this is for troubleshooting purposes, and it will get restrictive as soon as I figure this out Right now, the ASA5510 is pretty restrictive, and to be brutally honest, I'm not certain I'm even using the packet tracer 100% proper to be able to simulate coming from the outside of the network through my ASA5510, out to a remote ASA5505, and to a web server behind that 5505. I'm sure that the issue is probably going to be a mix of ACL's between the 5510, and the 5505.
I guess the main question, is Clientless SSL VPN really a good choice for this, or are there other real alternatives - especially since my client doesn't want to have to install, or use an actual client (like AnyConnect), nor do they want to have an always-on IPSEC VPN. Am I going about this the right way? Anyone have any suggestions, or do I have my config royally hosed?
Thanks much for any and all ideas!

Hey All, I appreciate all of the views on this post. I would appreciate any input - even if you think it might be far-fetched. I'm grasping at straws, and am super-hesitant to tell my customer this is even remotely possible if I can't have a POC myself. Thanks, in advance!!

Access to VPN and Skype from behind work's firewall

I'm running a Powerbook G4 with OS 10.4.11. At work I have a very fast ethernet connection perfect for internet and Work (Exchange) email, however I can't seem to access my Uni email account, VPN or several other services, notably Skype or iChat (as I work away from my kids during the week this is vitally important). I can ping the server for the VPN and both sets of IT boffins assure me that all appropriate ports are open. I can access the VPN through PCs and I am at the moment broadcasting the internet through my Airport to a PC based laptop which is running Skype quite happily. I can go to a local pub/coffee shop and access all of the services through a WiFi/Airport Network, and I have access to all these services when I'm at home (again through WiFi). What am I doing wrong? Any help would be greatly appreciated
D

Hi,
yes, the spilt into three subnets did help. I now can see the routers also from the LAN which solves Problem A)
Regarding the access from WAN1 to WAN2 the background is a long story about different flatrates from Provider A and B. To keep it short: DSL is stable but very slow during some hours of the day and attached to WAN2, LTE (4G) is fast but not stable (at least 2-3 hickups per day). Therefore I need the RV042 to keep the LAN clients always online as I need it for my job. The telephone is another issue. The fritzboxes do allow VOIP over their own Internet connection but also using another Fritzbox is possible. I have my telephones connected to the DSL Box (WAN2 = 192.168.179 now) and I have a flatrate for calls to cell phones with my 4G provider (WAN1 = 192.168.178 now). As the 4G keeps failing from time to time it is very annoying when it happens during a telco (and we all know Murphys law). So the ideas is to have the telphones attached to the stable (WAN2) DSL Box and reroute it for calls to cell phones via WAN1 ( which is a feature of the boxes and worked perfectly). If the 4G fails the DSL Box uses its own Internet connection to make the call (but then I have to pay for it).
So I need access from WAN2 (192.168.179) to WAN1 (192.168.178). I tried a static route in the WAN2 Box but it didn't work (I've used the RV042 WAN interface IP: 192.168.179.100 as Gateway).
Kind regards
Klaus

Performance end to end testing and comparison between MPLS VPN and VPLS VPN

Hi,
I am student of MSc Network Security and as for my project which is " Comparison between MPLS L3 VPN and VPLS VPN, performance monitoring by end to end testing " I have heard a lot of buzz about VPLS as becoming NGN, I wanted to exppore that and produce a comparison report of which technology is better. To accomplish this I am using GNS3, with respect to the MPLS L3 VPN lab setup that is not a problem but I am stuck at the VPLS part how to setup that ? I have searched but unable to find any cost effective mean, even it is not possible in the university lab as we dont have 7600 series
I would appreciate any support, guidence, advice.
Thanks
Shahbaz

Hi Shahbaz,
I am not completely sure I understand your request.
MPLS VPN and VPLS are 2 technologies meant to address to different needs, L3 VPN as opposed as L2 VPN. Not completely sure how you would compare them in terms of performance. Would you compare the performance of a F1 racing car with a Rally racing car?
From the ISP point of view there is little difference (if we don't want to consider the specific inherent peculiarities of each technology) , as in the very basic scenarios we can boil down to the following basic operations for both:
Ingress PE impose 2 labels (at least)
Core Ps swap top most MPLS label
Egress PE removes last label exposing underlying packet or frame.
So whether the LSRs deal with underlying L2 frames or L3 IP packets there is no real difference in terms of performance (actually the P routers don't even notice any difference).
About simulators, I am not aware of anyone able to simulate a L2 VPN (AtoM or VPLS).
Riccardo

VPN and Remote Desktop Connection

I have a standalone windows 2012 server that runs a domain with a few workstations. I have successfully configured a PPTP VPN and can connect using a Windows 7 computer at home. Once connected to the VPN, I can Remote Desktop to the server - but not any
other computers. The computer I'm trying to connect to runs Windows 7 and has remote desktop connections enabled.
Under the Access Details in the Remote Access Management the VPN connection is shown correctly first to the router (x.x.x.1) then the server (x.x.x.2) under Protocol 17 and Port 53. Then the server is shown again under Protocol 17 and Port 3389, which must
be the Remote Desktop connection. And then the workstation on the domain (x.x.x.20) also shows a connection with Protocol 17 and Port 3389. However, the remote desktop connection fails everytime. I'm not sure where the issue exists since it appears the server
is seeing and acknowledging the remote desktop connection. On my router I have PPTP passthrough enabled and port forward 3389 to the server.
I have attempted to use the workstations internal IP address as well as the computer name (workstation and workstation.domain.local) when connecting.
Thanks for your help.
I just noticed these three event errors on the destination remote machine. Not sure why it's trying to use L2TP?
Failed to apply IP Security on port VPN2-1 because of error: A certificate could not be found. Connections that use the L2TP protocol over IPSec require the installation of a machine certificate, also known as a computer certificate.. No calls
will be accepted to this port.
A certificate could not be found. Connections that use the L2TP protocol over IPsec require the installation of a machine certificate, also known as a computer certificate. No L2TP calls will be accepted.
The Secure Socket Tunneling Protocol service either could not read the SHA256 certificate hash from the registry or the data is invalid. To be valid, the SHA256 certificate hash must be of type REG_BINARY and 32 bytes in length. SSTP might not be able to
retrieve the value from the registry due to some other system failure. The detailed error message is provided below. SSTP connections will not be accepted on this server. Correct the problem and try again.

Morning Trent,
I don't know if this is still an issue for you, did you get it solved?
If not, check on the server whether the user credentials that you're using to RDP to the workstation are actually authorised server-side. If that checks out, on the VPN connection you can specify a protocol to use. Specify the protocol that your VPN is configured
to use on the server.

Configuring Admin Util to allow me to use VPN AND surf the rest of the net

I am having a problem when I connect to my work network via VPN. When I do, I can no longer connect to the rest of the Internet. I was able to do this until I started using an Express (so it has been allowed by my work network).
Here's my setup: Express is connected via Ethernet to my Verizon Fios modem. When I connect my computer directly to the Verizon modem all works fine. I have been advised that what's happening is that my Airport Express is creating a behind-the-device network that has the same exact IP address space as your office's network (when I'm connected to it via VPN).
To fix this I've been told to "Go into the Airport administration app, click on the "Internet" icon at the top of the configuration pane for your AE, then click on the "DHCP" tab, and look at what the "DHCP Range" pull-down menu is currently set to. After writing this down (in case you need to go back to it), change to one of the other options -- e.g., if it's currently set to "10.0.", change to "192.168." or "172.16". That should be enough to move you completely out of the space that your VPN is using. Save the changes, let your AE reboot, and try using the VPN and the internet at the same time again."
The problem is that the advisor is using Airport Admin Util version 5.x and I am using version 4.2. The screen he suggests is not where his is in his version. Could someone advise me of how I can do this via 4.2?

Reset your iPad and see if that fixes this.
Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.

VPN and Lion Server

I set up a VPN on my OS X Lion server however it seems there is a probelm with the file permissions. I set the permission to Read and Write, however when connected through the VPN I open a document, edit and save, it saves as a "read only" document and locks file. In Filemaker Pro if I create a document when connected through the VPN and save it on my server, no one connected to the network can open it. Any ideas?
Thanks

any help please?
I read that it my be firmware 7.5.2 and downgrading to 7.4.2 resolves it. Well, that would work if I had 7.4.2 but it's not available under the firmware update.

WRV54G and VPN and Windows 2003 Server

Hello. I use Windows 2003 Server on my laptop and trying to establish VPN into my WRV54G. QuickVPN is not compatible with the OS, so that's not an option. I tried the manual setup and I got to a point where I had to enter the destination IP address. I use a DynDNS address and so I won't have a static IP.
I'm using firmware version 2.39.2.
Thoughts?
Thanks!

First thing i would like you to check is if you are able to "ping" the WAN ip address for the WRV54G.
Also what are the settings that you have on the WRV ??? typically the remote secure group and remote security gateway should be set at "any".
In the WRV...under the VPn go to advanced VPN and sset the mode to "agressive" , enable keep-alive and netbios broadcast....
let me know if this work or let me know a few more details.

Problem SSO between VPN and NAC

Hello
Description of our problem : SSO doesn't work
-on the first connexion from vpn client we insert two time the login and password :one time for the client vpn and the seconde time for CAA (clean Access agent).
-although for the other connexion that succeed, we insert only one time the login and password (for vpn only) and for CAA the connexion is done automatiquely and a some hours later we reinsert two times login and password for vpn and CAA.
The following steps are done to configure Cisco NAC Appliance to work with a VPN concentrator:
Step 1 Add Default Login Page =ok
Step 2 Configure User Roles and Clean Access Requirements for your VPN users =ok
Step 3 Enable L3 Support on the CAS = ok
Step 4 Verify Discovery Host =ok (CAS IP ADDRESS 192.168.2.11)
Step 5 Add VPN Concentrator to Clean Access Server =ok (ASA IP ADDRESS 192.168.2.1)
Step 6 Make CAS the RADIUS Accounting Server for VPN Concentrator =ok
Step 7 Add Accounting Servers to the CAS (accounting server is CAM IP ADDRESS 192.168.20.10)
Step 8 Map VPN Concentrator(s) to Accounting Server(s)=ok
Step 9 Add VPN Concentrator as a Floating Device =ok
Step 10 Configure Single Sign-On (SSO) on the CAS/CAM =ok
the database for vpn authentication is cisco secure acs(192.168.1.30).
Tanks to any anybody to give us a possible solution.
FILALI Saad
Ares Maroc

Hi
I have just gone the the same issues with SSO VPN with my CAS in real-ip mode.
First thing to consider, when your testing, every time you test a user, make sure you go into the CAS or CAM and remove them as a certified device or active user before you perform your next test. I found that while I was testing that it would sometimes cache the user and I was getting successful auth attempts but due to their device being already accepted on a previous connection because the CAS was not made aware that the user had logged out correctly.
1. Make sure you have a fully functional DNS system on the inside network, I didnt realize how important it was to have forward and reverse look ups for your CAS and CAM. Make sure that all CAS and cams are listed in dns with correct domain names.
This in very important if your running your own CA certificates on cas and cam. Make sure that the CAM and CAS can resolve each other via dns. Make sure the CAM and CAS can perform reverse lookups of each other. Also make sure that when the user VPN's into your ASA that they can also perform DNS lookups and reverse lookups. If they cant perform dns look ups, you may need to temporarily allow the untrusted network full access while you resolve the DNS lookup problem on the client computer. One of the issues I had was that the VPN clients couldnt resolve internal DNS names and so the CCA agent would never auto pop-up and start the auto login process because it was trying to resolve the CAM name and also check that the CA certificate I had on the CAS was legitimate as I had used names in my certs and not IP addresses.
2. Make sure your VPN group settings on the IPSEC policy of the ASA has DNS pointing to your internal DNS server.
3. I know you already said you have done this but check to make sure that the VPN group setup on your ASA for your remote access users, has been setup with the radius accounting being directed the INSIDE interface IP address of your CAS, (if you are running your CAS in real-ip, I found that the inside interface was the only interface listening on 1813, do a 'netstat -an' on the cas to check) if your running in VGW mode then you only have 1 ip address to direct it to anyway.
Follow from step 15 in following link
http://www.cisco.com/en/US/products/ps6128/products_configuration_example09186a008074d641.shtml
3. Troubleshoot and make sure that the ASA actually sends a radius accounting message to the CAS. I did this by ssh into the CAS and doing a 'tcpdump -i any src and not tcp 22'. I then logged into the VPN client and made sure that once I entered my vpn user and pass, that the ASA authenticates the vpn user and then passes a radius accounting message to the CAS informing the CAS it has allowed a new user. If you dont see this radius accounting message hit the CAS interface go back to my step 3 and resolve.
4. Finally check that you have not mistyped a shared secret somwhere, ie between CAM and ACS, Between ASA and ACS, Between ASA and CAS. I had all my users authenticate though radius on my ACS server, a number of times I got caught out by a simple typo in a shared secret.
Try these things first.
Also someone else here on the forums linked this guide to me that also helped me setup my CAS correctly.
http://www.cisco.com/en/US/docs/security/nac/appliance/configuration_guide/412/cas/s_vpncon.html
You may find it useful too.
Dale

Best option for VPN and Firewall..

I am replacing my Watchguard Firebox 700 Firewall/VPN with a Cisco box. I am trying to determine what would be the best model for my environment.
20 person company.. The only need would be for 1 or 2 different offices to connect via VPN and also our users to connect via VPN. So my needs are for firewall and VPN.. What model would you recommend?
Thank you

Hi,
I would suggest ASA 5505. Take a look at the link below.
http://www.cisco.com/en/US/products/ps6120/prod_models_comparison.html
Rate it, if it helps.
Thanks
Gilbert

On my 2nd gen itouch i accidently hit vpn and now i cant go back to wifi

I can not get back to wifi on my 2nd gen ipod because I went into vpn and now it won't let me do wifi.

To recover from a lost Restrictions passcode:
- Restore from a backup that was make before you added the Restrictions passcode. If you restore from a backup made with the Restrictions passcode the Restrictions passcode is also restored.
- Restore to factory settings/new iPod.
- If you are up to it see:
How to reset forgotten Restrictions...: Apple Support Communities
How to reset forgotten Restrictions...: Apple Support Communities

Mac, VM XP Pro, Cisco VPN, and Printing.

I have an end user running a Mac with a VM XP Pro Machine that connects to our corperate VPN. This part works just fine. The problems come up when he tries to print to a local network printer. The job just sits until he disconnects from the VPN and then it prints just fine. Does anyone know what to do to fix this? I have little or no MAC knowledge.
Regards,
Dan

That's what I figured but I hoped someone would have dealt with this in the past and have a work around other than split tunneling.
Thanks,
Dan

VPN and racoon in foreground

Similar Messages

Maybe you are looking for