VPN Auto Reconnect

Hello, I'm using VPN(PPTP) to connect to my office but sometimes the connection is not stable and I got a lot of disconnection. Is there a way to auto reconnect to the VPN Server?

Seems like you should be able to Script it, but I wonder if this Widget might help, seems to have a reconnect feature for PPP, so maybe more...
http://www.apple.com/downloads/macosx/networking_security/netmonitor.html

Similar Messages

  • SR520 Auto Reconnect VPN Remote Connection

    Hi,
    I am new to the SR520 router, and I have gotten the vpn server and remote to work. We have 3 of these routers, one at our corporate site, and one at each of our remote sites. The VPN's work good, but I would like them to auto-reconnect because we have some voice traffic that needs to pass over them, and the staff is not very capable of using the connection tool. Is this possible? Is there a time out on them that I can remove?
    I have only used the Cisco Configuration Assistant to configure them, and when I used the command line, the vpn's wouldn't work.
    Any help would be appreciated.

    Addis and I connected with Andy Hickman who share the following that could work for this.
    To keep the tunnel up you can use the auto connect feature of EZVPN.  This is pretty straight forward, just do the following:
    Starting from a standard configuration built by CCA1.9 for remote access, use the following to allow the remote router to connect automatically to the UC500 VPN server.
    On the UC500, add the following configuration via CLI:
    crypto isakmp client configuration group EZVPN_GROUP_1
      save-password
    On the remote device (870 or SR520), add the following configuration via CLI:
    crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1
      username password
    It is also strongly recommended that password encryption is configured on the remote device:
    password encryption aes
    key config-key password-encrypt

  • Linkstation NAS and auto reconnect

    I am connecting to a Buffalo Linkstation using SAMBA and can mount the shares just fine (I keep my iTunes music on it for my Sonos sound system). I can get the shares to mount on startup, but they seem to auto-disconnect at some point and I have to manually reconnect to them through the Finder.
    Is there anyway to get them to auto reconnect?

    I'm dealing with the same thing. but mine got worse. (I have a linksys NSA for USB drives) I used to have to manually connect via the finder. A bummer, but at least that worked. now, in the finder nothing pops up under that workgroup. The printserver is supposed to show p also. the printserver works, just doesn't show up in finder)
    OK, I know you can mount via the command line. I'm gonna dig around and get the answer. (ok, i know that iI can if Apple didn't mollest unix that bad)

  • How do you auto reconnect a live video stream broadcast in flash action script 3?

    how do you auto reconnect a live video stream broadcast in flash action script 3?
    so i don't have to ask people to refresh the page if the connection drops
    i copy pasted the live video stream broadcast files and script from here;
    http://www.adobe.com/devnet/adobe-media-server/articles/beginner_live_fms3.html
    http://www.adobe.com/content/dotcom/en/devnet/adobe-media-
    server/articles/beginner_live_fms3/_jcr_content/articlePrerequistes/multiplefiles
    /node_1278314297096/file.res/beginner_live_fms3.zip
    i don't know what i'm doing

    Why don't you use several layers with appropriate alpha properties, and move these layers according to the mouse events?

  • Restart -- Magic Mouse does not auto-reconnect

    After I updated OS from 10.6.4 to 10.6.5 with the combo updater, upon restart my Magic Mouse no longer auto-reconnect via Bluetooth. I even applied the combo updater for the second time. But, every time I restart my Mac, I have to use a USB mouse to reconnect the Magic Mouse back to the Mac.
    How can I bring the auto-reconnect back? This is driving me crazy.

    I believe that I have solved the issue with the following procedure.
    [0] Let's suppose that, after a restart, the Magic Mouse did not auto-connect.
    [1] Use a USB mouse to open *System Preferences > Bluetooth*.
    [2] In the left-side window, select the Magic Mouse.
    [3] At the bottom of this left-side window, pull down the menu and select *Update Device Services*.
         It may take a moment or two for the update to occur.
    [4] In the left-side window, the Magic Mouse should now appear as Connected.
    [5] Restart the Mac and see if the Magic Mouse auto-connects now.

  • SAP ISU Auto Reconnection on payment receipt

    Hi Friends,
    We need to Automate the process of Auto reconnection on payment received.
    i.e When payment received from customer through FPCJ tcode
    system will look for the disconnection status and do as follows
                If disconnection Status is 20(Disconnection Started)
                   then change Disconnection status to 99( Completed)
    1. How can we change this staus from 20 to 99 ?
    2. What function fodule to be used for doing this status change.
    3. What are the parameters we need to pass to function module for doing this activities.
    Thanks
    SK

    Hi,
    It can be done in following steps:
    1. Use function module ISU_S_DISCDOC_PROVIDE to populate your AUTO parameter by passing disconnection document.
    2. Update following parameters:
    AUTO-CONTR-USE-OKCODE    = 'X'.
    AUTO-CONTR-OKCODE = 'DARKCOMPL'.
    3. Call function module ISU_S_DISCDOC_CHANGE.
    This will complete disconnection document.
    Hope this helps.
    Regards,
    Avinash

  • How can i make my java app auto reconnect to Oracle.

    Scenario:
    when i am working with my java app if suddenly Oracle server connection unplugged. Then i got some problems regarding database.
    When they replugged the connection, i need to restart my app again. Then it works fine.
    Question:
    When the database is replugged or restarted, then how can i reconnect to the DB automatically with out restart my app. Please letme know is there any auto reconnect process is there for Oracle.

    If you want your application to reconnect, you would need to add logic that catches the exception that gets thrown when the connection is lost and tries to reconnect.
    Justin

  • After ejecting my drive it auto reconnects

    Hi,
    I have had this problem with Snow Leopard and Lion.
    When I connect my cellphone (HTC WM6.5) everything works fine but when I eject the device it auto-reconnects before I get the chance to pull the cable, giving me a faulty removal error.
    Ok it's not a major issue but I'm just wondering why.
    Anyone some ideas besides it's Bill Gates to blame?

    You can check by selecting the iPod Touch from under devices.  This will bring you to the iPod's Summary tab.  On this screen, check to see if the Sync over Wi-Fi option is enabled.
    How exactly are you ejecting the device?
    B-rock

  • Auto reconnect after sleep, depends on brightness

    Found this deep in 'weak wi-fi' thread and as it is not explicitly related to weakness of wi-fi signal decided to post it here. If you experiences auto-reconnect problem after waking up an Ipad and brightness was set to minimum try to move brightness slider a little bit to the right and try.
    In my configuration dependency was 100%.

    actually all credits should go to the original author (batgzam) here http://discussions.apple.com/thread.jspa?threadID=2391395&tstart=30
    Apple should have been put this information to broad public - via this board, e-mail - whatever. Assume thousands people calling there support with regard to this particular problem and solution. Not giving this information to public means wasting hundreds thousand hours of their customers time and patience.

  • E72 & VoIP Auto-Reconnect

    I have successfully setup my E72 for SIP calls and it works very well for the most part.
    There is one problem however that means it is very annoying to use.
    The problem is that whenever I move out of a WiFi area and therefore get disconnected from the SIP server, the phone doesn't automatically reconnect to the SIP server when I get back in range of a WiFI area.
    At the moment I therefore have to restart the phone every time I return to a WiFi enabled area to force the phone to reconnect the SIP server. The problem is not with WIFI - this reconnects fine when back in range automaitcally, it is just the SIP server that doesn't auto-reconnect.
    Is there any way to force the phone to reconnect to SIP after disconnection without rebooting it every time please?
    PS I have also tried setting SIP to work over 3G. This works fine but I then get the same problem when I leave a 3G signal area!
    Thanks

    paulbula, I noticed the same problem on my e72. Yes, I can confirm e72 does not reconnect on wifi.
    You also write that you have the same problem on 3G i.e. your e72 does not reconnect to sip server automatically. Well, my e72 does reconnect but the problem is that it needs too much time to reconnect which is very anoying and makes normal nokia sip calling via 3G impossible while walking, driving or when calling in bad network coverage. When I use nokia sip on my nokia n95 8GB I do not have this annoying 3G reconnect problem so this is a e72 problem which needs to be fixed by nokia!
    I describe this problem more in another nokia thread - google for "e72 3x sip hangs".

  • Sun JMS  version 8.0 auto-reconnect.

    Hi,
    I am using SunAppserver version 8.0 . I have a application which reads the message published on to a JMS bus. I am trying to implement auto-reconnect functionality , i.e When the JMS server is stopped , my appliaction would wait for the JMS server to come up & reintializes the connection. When it does that i am getting below exception.
    createQueueSession:javax.jms.IllegalStateException: [C4062]: Cannot perform operation, connection is closed.
    Any inputs is appreciated.

    To me it looks like you're trying to access a session from another thread. The session objects a single threaded.

  • Vpn auto connect

    Hi, I were using the VPN auto Connect script from Fardjad's blog.
    on i
    o
    on idle
              tell application “System Events”
                        tell current location of network preferences
                                  set myConnection to the service “VPN”
                                  if myConnection is not null then
                                            if current configuration of myConnection is not connected then
                                                      connect myConnection
                                            end if
                                  end if
                        end tell
                        return 120
              end tell
    end idle
    It worked fine until I updatetd to 10.7.3 and beyond.
    http://fardjad.wordpress.com/2010/11/11/vpn-auto-connect-script/

    I recommend that you check the network traffic by using either Wireshark or Fiddler to see what's going on with the request.
    Matt Small - Microsoft Escalation Engineer - Forum Moderator
    If my reply answers your question, please mark this post as answered.
    NOTE: If I ask for code, please provide something that I can drop directly into a project and run (including XAML), or an actual application project. I'm trying to help a lot of people, so I don't have time to figure out weird snippets with undefined
    objects and unknown namespaces.

  • Powerbook g3 will  not auto reconnect to iMac airport after sleep

    iMac is a late-2006 intel, airport extreme. I'm internet sharing. If the powerbook sleeps, it will not auto-reconnect after waking. I can't even enter the password to reconnect; it displays an error message. I have to turn off-and-on the iMac's airport, and then the powerbook auto-reconnects.

    Welcome to the discussions, Dan!
    If the powerbook sleeps, it will not auto-reconnect after waking.
    The AirPort Extreme is "always on", there are no "sleep" related adjustments on this device. The "sleep" issue is with your powerbook or the operating system that the powerbook is using.
    Suggest that you post in the PowerBook Forum for your specific question.

  • After sleep, Pismo will not auto-reconnect to iMac's airport extreme.

    I'm internet sharing with an iMac, late-2006 intel, airport extreme. If the powerbook sleeps, it will not auto-reconnect after waking. I can't even enter the password to reconnect; it displays an error message. I have to turn off-and-on the iMac's airport, and then the powerbook will connect.

    Welcome to the discussions, Dan!
    If the powerbook sleeps, it will not auto-reconnect after waking.
    The AirPort Extreme is "always on", there are no "sleep" related adjustments on this device. The "sleep" issue is with your powerbook or the operating system that the powerbook is using.
    Suggest that you post in the PowerBook Forum for your specific question.

  • IChat 4: Auto-reconnect, best to use AIM/GTalk or our OS X Server

    Hey guys. I have two questions. Our internet has been extremely flaky and it makes it extremely difficult and frustrating to have video chats between our offices. Every time we have a connection error, the session terminates and we get the error message prompting us to send the report to Apple or ignore. Can I automatically suppress this option to send the report and close the window? Or, better yet, could I set up something (AppleScript?) to automatically recreate the video chat? I already have the AppleScript set up to auto accept the video chat invitation when someone tries to contact us, but I would love it if we could set up a script that auto-contacts other people in a video chat.
    My second question, which is sort of related, at least to performance, has to deal with the best service to use for chatting. We currently use AIM for all of our inter-office text and video chatting needs. We also have an OS X Server, but it's co-located out of our office. Which would be the preferred network to use, if we're just contacting each other? I would have to think AIM because they probably have hundreds of servers, but they also have millions of users. We would have just a handful at a time using ours. Your thoughts on server preference, especially when video is a priority?
    Thanks!

    iChat does not have an Auto Reconnect item as such.
    However if iChat is using an External Camera there is a setting in the iChat > Preferences > Video section that says Connect if Camera is On which will do just that.
    iChat 4 does have a item for remembering open chats across logins/restarts of iChat.
    This is set in the Messages section of the Preferences.
    I am not sure if Chax includes and Auto Reconnect feature or not.
    This may help
    tell application "iChat"
    if status is offline then
    log in
    end if
    set originalStatus to the status message
    end tell
    10:03 PM Friday; June 20, 2008

Maybe you are looking for