VPN Client - Assigned wrong netmask?

I am having problems with a VPN setup that has previously been working. The VPN Client connects OK (V4.6.04.0043) however, if I check the IP address & mask assigned by the router I see :-
IP Address : 172.22.80.126
Subnet Mask : 255.255.0.0
Gateway : 172.22.80.126
DNS Servers : 172.22.1.240
If I try and ping anything on the LAN I get no response. I can ping my own IP.
Using the same client I can connect sucessfully to several other VPN gateways - all of these give me what I would expect to be the correct mask of 255.255.255.0
Can anyone shed any light on this?
IOS on the non-working setup is - 12.2(11)T6
Andy.

it's normal. when the router assigns ip address from the pre-configured pool, it determines the mask according to the class of ip. with your case the mask will be 255.255.0.0 as the ip is 172.x.x.x. if the pool is 10.x.x.x then the mask will be 255.0.0.0.
it will work except the pc itself has another route to 172. to verify, do a route print on the pc.
a way to verify the issue is to connect the vpn via a dialup connection. in that case you will be able to identify whether the issue is with the pc, vpn software, or the router config

Similar Messages

Subnet mask 255.255.255.255 assigned to VPN client - can't ping LAN

Hi,
I configured PIX 501 with PPTP VPN to connect to the small office (PIX FW, Win 2000 Server, several Win clients, LAN IP 10.0.0.X/24):
ip local pool mypool 10.0.0.101-10.0.0.105
vpdn group mygroup accept dialin pptp
vpdn group mygroup ppp authentication mschap
vpdn group mygroup ppp encryption mppe 128 required
vpdn group mygroup client configuration address local mypool
vpdn group mygroup client configuration dns 10.0.0.15
vpdn group mygroup pptp echo 60
vpdn group mygroup client authentication local
vpdn username xxxx password *********
vpdn enable outside
I can connect to the office using Win VPN client, but I can't ping any hosts in the office network. I suspect that the reason for that is subnet mask assigned to the VPN client: 255.255.255.255. ipconfig of the VPN client:
PPP adapter Office:
Connection-specific DNS Suffix . :
IP Address. . . . . . . . . . . . : 10.0.0.101
Subnet Mask . . . . . . . . . . . : 255.255.255.255
Default Gateway . . . . . . . . . :
Default GW is missing too, but I think this is not the main problem.
Any way, what is wrong with my config? How to fix subnet mask assigned to clients? Or may be my assumption is wrong and this mask is ok? What is wrong then?
Any input will be greatly appreciated!
George

Thanks for the prompt reply.
Here it does:
PIX Version 6.3(4)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password xxxxxxxxxxxxxx encrypted
passwd xxxxxxxxxxxxxx encrypted
hostname OSTBERG-PIX
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list 80 permit ip 10.0.0.0 255.255.255.0 10.0.20.0 255.255.255.0
access-list inbound permit icmp any any
access-list inbound permit tcp any any eq pptp
access-list inbound permit gre any any
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside 66.189.xxx.xxx 255.255.252.0
ip address inside 10.0.0.23 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool mypool 10.0.0.101-10.0.0.105
pdm location 10.0.0.0 255.255.255.0 inside
pdm location 10.0.0.15 255.255.255.255 inside
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
access-group inbound in interface outside
route outside 0.0.0.0 0.0.0.0 66.189.yyy.yyy 1
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
sysopt connection permit-pptp
telnet 10.0.0.23 255.255.255.255 inside
telnet 10.0.0.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
vpdn group mygroup accept dialin pptp
vpdn group mygroup ppp authentication mschap
vpdn group mygroup ppp encryption mppe 128 required
vpdn group mygroup client configuration address local mypool
vpdn group mygroup client configuration dns 10.0.0.15
vpdn group mygroup pptp echo 60
vpdn group mygroup client authentication local
vpdn username ********* password *********
vpdn enable outside
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd auto_config outside
terminal width 80
Cryptochecksum:xxx
: end
There are remnants of old config, I just recently took over this network, some lines look odd to me, but I did not touch what works. VPN config is all mine.
PIX internal 10.0.0.23 - is a gateway for the network. DNS server in LAN - 10.0.0.15.
I've been reading about the problem and came across several posts that this subnet mask is normal, but it puzzles me - how can this host communicate with anyone else if there is no room for other hosts in this network (according to the mask)?!
Thanks again!
George

Assigning 2 DNS servers to VPN clients

It seems like I can only assign 2 DNS servers to VPN clients using the "dns-server" command in config-group-policy? How do I go about assigning more than 2?
what exactly does dns server-group do? Can I use that command to assign dns servers to vpn clients since I can add more than 2 dns servers?

ciscoasa# sh run
: Saved
ASA Version 8.0(4)
hostname ciscoasa
enable password c.LHJMlCqC0Qvrsf encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
speed 100
duplex full
nameif outside
security-level 0
ip address extip 255.255.255.240
interface Ethernet0/1
speed 100
duplex full
nameif inside
security-level 100
ip address 172.17.193.100 255.255.255.0
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
management-only
boot config disk0:/exit
ftp mode passive
clock timezone mst -7
clock summer-time mdt recurring
dns domain-lookup inside
dns server-group TA-UAT
name-server 44.44.44.102
domain-name ta.corp.adds
access-list split_tunnel_list standard permit 172.17.193.0 255.255.255.0
access-list split_tunnel_list standard permit 44.44.44.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 172.17.193.0 255.255.255.0 192.168.20.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 44.44.44.0 255.255.255.0 192.168.20.0 255.255.255.0
access-list inbound_on_outside extended permit icmp any any
access-list inbound_on_outside extended permit tcp any host extip eq 5555
access-list inbound_on_outside extended permit tcp any host extip eq www
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu management 1500
ip local pool vpnuserspool 192.168.20.101-192.168.20.254 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
icmp deny any outside
asdm image disk0:/asdm-613.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 44.44.44.0 255.255.255.0
nat (inside) 1 172.17.193.0 255.255.255.0
static (inside,outside) tcp extip 5555 172.17.193.96 5555 netmask 255.255.255.255
static (inside,outside) tcp extip www 172.17.193.1 www netmask 255.255.255.255
access-group inbound_on_outside in interface outside
route outside 0.0.0.0 0.0.0.0 extip 1
route inside 44.44.44.0 255.255.255.0 172.17.193.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable
http 192.168.20.0 255.255.255.0 inside
http 172.17.193.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.0 management
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set firstset esp-3des esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map dyn1 1 set transform-set firstset
crypto dynamic-map dyn1 1 set security-association lifetime seconds 28800
crypto dynamic-map dyn1 1 set security-association lifetime kilobytes 4608000
crypto dynamic-map dyn1 1 set reverse-route
crypto map mymap 1 ipsec-isakmp dynamic dyn1
crypto map mymap interface outside
crypto isakmp enable outside
crypto isakmp policy 1
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 43200
crypto isakmp nat-traversal 3600

Can we assign IPv4 IP address pool to IPv6 VPN Client

We are planning to enable IPv6 SSL VPN clients, Let me explain the current setup
We have Cisco ASA firewall used for SSL VPN and Cisco ACS for user authentication and RSA for two factor authentication.
LAN Server are in IPv4 only..
Requirement :
Client (IPv6) --- Cloud (IPv6) ---- Outsite(IPv6) -Cisco ASA - Inside(IPv4) ----- ACS (IPv4) & RSA (IPv4)
Client with IPv6 internet connectivity connect to SSL VPN with IPv6, Cisco ASA outside interface with IPv6 address will receive the request.
Qus:
1. Will Cisco ASA check two factor authentication with ACS and RSA both are in IPv4 address for an IPv6 client ?
2. Once if authenticated, Cisco ASA can assign IPv4/IPv6 address pool to the client, if i prefer only IPv4 address pool and client will get IPv4 address as tunnel interface IP address. Will it work? Means IPv4 over IPv6 SSL VPN tunnel.
Thanks
Sankar

AFAIR, with SSL we support IPv4 and IPv6 assigned IP addresses, with IPsec IKEv2 we only support IPv4 addressing.
Query to AAA servers are separate process, from user<-> headend authentication flow, unless we're talking about IKEv2 with standard EAP methods.

Assign ACLs to VPN clients

We have a customer who VPN's to a Pix 515. I inserted the same-security-traffic permit intra-interface configuration on the pix so that personnel who utilize teh VPN would be able to access one specific resource on the public side. What I would like to do is continue to use the same-security-traffic permit intra-interface command, but limit access to other resources to the VPN client. Can I assign an access list to the VPN client that would permit 10.10.10.10 to any and then deny all other connections? Where do I insert this in the VPN structure?
Thank you

You should be able to accomplish this using "vpn-filter value". Please refer the below URL for details.
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a0080641a52.shtml
Regards,
Arul
** Please rate all helpful posts **

Assign Static IP to VPN clients authenticated on AAA server

Hi NetPros
My objective is to assign static IP address for VPN clients.
The tunnel group authentication is on a AAA LDAP server.
AAA LDAP queries has been configured and tested to work.
I followed the guide below, but could not get static IP assignment to work.
http://www.cisco.com/en/US/docs/security/asa/asa80/asdm60/selected_topics/enforce_AD.html#wp41996
The tunnel group is configured to use the DHCP pool and the Group policy on ASA.
- If i do not specify dhcp pool, the error message is: "no assigned address"
- If i configure dhcp pool, the assigned address will be from the pool
Here are my queries on assigning a static IP for aaa-users:
1. Do you need to configure a external policy server for static IP assignment to work?
-I prefer to use the group policy on ASA
2. Under the tunnel profile, do you need to specify what DHCP pool to use? If yes, what do i specify?
3. Does DHCP service needs to be running on ldap server?
4. As per printscreen below, is Remote Access Policy required?
5. What am I missing out to make static IP assignment work?
Big thanks

Hi all
Thanks to friends working in Cisco, they have helped to identify the root cause.
The root cause was due to a misprint on the Cisco document.
The correct LDAP attribute is: msRASSavedFramedIPAddress. Note on the additional 'd' after the word, 'Frame'
In fact this LDAP attribute was also lacking of a 'd' on the ASDM scroll down selection. Would appreciate if someone relay the mistake to cisco personnel. Thanks all.

Assign Route to Windows 2K or XP VPN Client

Is it possible via radius, PIX vpdn, or IOS vpdn configuration to assign a route to a Windows 2K or XP VPN client?

it is possible in VPN concentrator where we can send a default route to the VPN client, not sure if it works in PIX.

I cannot route to remote subnets from cisco vpn client and pptp client

Hi guys,
I've a big problem, I configured a 877 cisco router as a cisco vpn server (the customer use it to connect to his network from pc) and a pptp vpn server (he use it to connet to the network from a smartphone).
In this router I created 2 vlan, one for wired network (192.168.10.0/24) and the second one (10.0.0.0/24) for wireless clients and I use fastethernet 3 port to connect these to the router.
this is the issue, when the customer try to connect to a wireless network from both of vpn clients he cannot do this, but if he try to connect to a wired network client all working fine.
following the addresses taken from the router.
- encrypted vpn client -
ip address. 192.168.10.20
netmask 255.255.255.0
Default Gateway. none (blank)
- pptp vpn client -
ip address. 192.168.10.21
netmask. 255.255.255.255
Default Gateway. 192.168.10.21
Is possible that I cannot reach the remote subnet because the clients doesn't receive a gateway (in the first case) or receive the wrong subnet/gateway (in the second one)..?
There is anyone can help me..?
Thank you very much.
Many Kisses and Kindly Regards..
Ilaria

The default gateway on your PC is not the problem, it will always show as the same IP address (this is no different when you dial up to an ISP, your DG will again be set to your negotiated IP address).
The issue will be routing within the campus network and more importantly on the PIX itself. The campus network needs a route to the VPN pool of addresses that eventually points back to the PIX.
The issue here is that the PIX will have a default gateway pointing back out towards your laptop. When you establish a VPN and try and go to an Internet address, the PIX is going to route this packet according to its routing table and send it back out the interface it came in on. The PIX won't do this, and the packet will be dropped. Unless you can set the PIX's routing table to forward Internet packets to the campus network, there's no way around this. Of course if you do that then you'll break connectivity thru the PIX for all the internal users.
The only way to do this is to configure split tunnelling on the PIX, so that packets destined for the Internet are sent directly from your laptop in the clear just like normal, and any packet destined for the campus network is encrypted and sent over the tunnel.
Here's the format of the command:
http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_62/cmdref/tz.htm#1048524

AAA static IP address for RA VPN Client

Hi,
my vpn group and VPN POOL is locally created in Cisco VPN router but users are authenticated through ACS, AAA server via TACACS. Now I want to assign the static ip address to VPN Client. Everything is fine but due to the application problem I want to give them the static Ip address from the VPN Pool. I have greated one pool in AAA server and also configure the client in AAA to get the static ip address but unable to do this. Please help me out how to do this.
My router is configured for TACACS+. I have checked the user configuration in AAA server to get the static ip address but it is not working. Please help me out how to do this. I cant change Router to Radius but this is my main router which is configured for 160 sites through ISDN and these sites also configured for TACACS+.
crypto isakmp policy 10
encr 3des
authentication pre-share
group 2
crypto isakmp client configuration group Aviation-VPN
key egntosc
pool aviation-pool
acl avi-tunnel
save-password
netmask 255.255.255.0
crypto isakmp profile vpnclient
   match identity group Aviation-VPN
   client authentication list default
   isakmp authorization list Aviation-authorization
   client configuration address respond
crypto ipsec transform-set aviset esp-3des esp-sha-hmac
crypto dynamic-map avi 10
set transform-set aviset
set isakmp-profile vpnclient
reverse-route

Since you're using ACS, I believe the way to do this is to
go into ACS, and select the username of the user that you want
to get the static IP. Under that user's setup, there is an option to
always assign the same IP. Just select that and enter the IP you
want them to get. - chris

Remote Access VPN Clients Cannot Access inside LAN

I have been asked to set up remote access VPN on an ASA 5505 that I previously had no invlovement with. I have set it up the VPN using the wizard, they way I normally do, but the clients have no access to anything in the inside subnet, not even the inside interface IP address of the ASA. Thay can ping each other. The remote access policy below that I am working on is labeled VPNPHONE, address pool 172.16.20.1-10. I do not need split tunneling to be enabled. The active WAN interface is the one labeled outside_cable.
: Saved
ASA Version 8.2(1)
hostname ASA5505
domain-name default.domain.invalid
enable password eelnBRz68aYSzHyz encrypted
passwd eelnBRz68aYSzHyz encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 192.168.100.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group dataDSL
ip address 76.244.75.57 255.255.255.255 pppoe
interface Vlan3
nameif dmz
security-level 50
ip address 192.168.9.1 255.255.255.0
interface Vlan10
nameif outside_cable
security-level 0
ip address 50.84.96.178 255.255.255.240
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
switchport access vlan 10
interface Ethernet0/2
switchport access vlan 3
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
clock timezone CST -6
clock summer-time CDT recurring
dns server-group DefaultDNS
domain-name default.domain.invalid
same-security-traffic permit intra-interface
object-group service Netbios udp
port-object eq 139
port-object eq 445
port-object eq netbios-ns
object-group service Netbios_TCP tcp
port-object eq 445
port-object eq netbios-ssn
object-group network DM_INLINE_NETWORK_1
network-object host 192.168.100.177
network-object host 192.168.100.249
object-group service Web_Services tcp
port-object eq ftp
port-object eq ftp-data
port-object eq www
port-object eq https
object-group network DM_INLINE_NETWORK_10
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_11
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_2
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_3
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_4
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_5
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_6
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_7
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_8
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_9
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network VPN
network-object 192.168.255.0 255.255.255.0
access-list outside_access_in extended permit icmp any host 76.244.75.61
access-list outside_access_in extended permit tcp any host 76.244.75.61 eq ftp
access-list outside_access_in extended permit tcp any host 76.244.75.61 eq ftp-data
access-list outside_access_in extended permit tcp any host 76.244.75.62 eq www
access-list outside_access_in extended permit tcp any host 76.244.75.62 eq https
access-list outside_access_in extended permit tcp any host 76.244.75.59 eq www
access-list outside_access_in extended permit tcp any host 76.244.75.59 eq https
access-list outside_access_in extended permit tcp any host 76.244.75.60 eq www
access-list outside_access_in extended permit tcp any host 76.244.75.60 eq https
access-list outside_access_in extended permit tcp any host 76.244.75.58 eq www
access-list outside_access_in extended permit tcp any host 76.244.75.58 eq https
access-list dmz_access_in remark Quickbooks
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_6 host 192.168.100.5 eq 56719
access-list dmz_access_in remark Quickbooks range
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_7 host 192.168.100.5 range 55333 55337
access-list dmz_access_in extended permit udp object-group DM_INLINE_NETWORK_8 host 192.168.100.5 eq 1434
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_9 host 192.168.100.5 eq 49398
access-list dmz_access_in remark QB
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_10 host 192.168.100.5 eq 8019
access-list dmz_access_in extended permit udp object-group DM_INLINE_NETWORK_2 host 192.168.100.5 eq 2638
access-list dmz_access_in extended permit udp object-group DM_INLINE_NETWORK_11 host 192.168.100.5 object-group Netbios
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_3 host 192.168.100.5 object-group Netbios_TCP
access-list dmz_access_in extended deny ip host 192.168.9.4 host 192.168.100.5 inactive
access-list dmz_access_in extended permit udp object-group DM_INLINE_NETWORK_4 any
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_5 any
access-list dmz_access_in remark Printer
access-list dmz_access_in extended permit ip 192.168.9.0 255.255.255.0 object-group DM_INLINE_NETWORK_1
access-list dmz_access_in extended permit tcp 192.168.9.0 255.255.255.0 any object-group Web_Services
access-list dmz_access_in extended permit udp 192.168.9.0 255.255.255.0 any eq domain
access-list dmz_access_in extended permit icmp 192.168.9.0 255.255.255.0 192.168.255.0 255.255.255.0 echo-reply
access-list dmz_access_in extended permit icmp 192.168.9.0 255.255.255.0 192.168.100.0 255.255.255.0 echo-reply log disable
access-list dmz_access_in remark QB probably does not need any udp
access-list dmz_access_in extended permit udp host 192.168.9.4 host 192.168.100.5 eq 55333 inactive
access-list dmz_access_in remark QB included in other rule range
access-list dmz_access_in extended permit tcp host 192.168.9.4 host 192.168.100.5 eq 55333 inactive
access-list dmz_access_in remark May be required for Quickbooks
access-list dmz_access_in extended permit icmp host 192.168.9.4 host 192.168.100.5
access-list CAD_capture extended permit ip host 192.168.9.4 host 192.168.100.5
access-list CAD_capture extended permit ip host 192.168.100.5 host 192.168.9.4
access-list inside_nat0_outbound extended permit ip any 192.168.255.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.255.0 255.255.255.240
access-list inside_nat0_outbound extended permit ip any 172.16.10.0 255.255.255.240
access-list inside_nat0_outbound extended permit ip any 172.16.20.0 255.255.255.240
access-list cad_supplies_RAVPN_splitTunnelAcl standard permit 192.168.100.0 255.255.255.0
access-list cad_supplies_RAVPN_splitTunnelAcl standard permit 192.168.9.0 255.255.255.0
access-list dmz_nat0_outbound extended permit ip any 192.168.255.0 255.255.255.0
access-list outside_cable_access_in extended permit icmp any host 50.84.96.182
access-list outside_cable_access_in extended permit tcp any host 50.84.96.182 eq ftp
access-list outside_cable_access_in extended permit tcp any host 50.84.96.182 eq ftp-data
access-list outside_cable_access_in extended permit tcp any host 50.84.96.183 eq www
access-list outside_cable_access_in extended permit tcp any host 50.84.96.183 eq https
access-list outside_cable_access_in extended permit tcp any host 50.84.96.180 eq www
access-list outside_cable_access_in extended permit tcp any host 50.84.96.180 eq https
access-list outside_cable_access_in extended permit tcp any host 50.84.96.181 eq www
access-list outside_cable_access_in extended permit tcp any host 50.84.96.181 eq https
access-list outside_cable_access_in extended permit tcp any host 50.84.96.179 eq www
access-list outside_cable_access_in extended permit tcp any host 50.84.96.179 eq https
access-list Local_LAN_Access standard permit host 0.0.0.0
access-list vpnusers_spitTunnelACL extended permit ip 192.168.100.0 255.255.255.0 any
access-list nonat-in extended permit ip 192.168.100.0 255.255.255.0 172.16.20.0 255.255.255.0
pager lines 24
logging enable
logging buffered informational
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu dmz 1500
mtu outside_cable 1500
ip local pool VPN_IP_range 192.168.255.1-192.168.255.10 mask 255.255.255.0
ip local pool VPN_Phone 172.16.20.1-172.16.20.10 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat-control
global (outside) 10 interface
global (outside_cable) 10 interface
nat (inside) 0 access-list nonat-in
nat (inside) 10 0.0.0.0 0.0.0.0
nat (dmz) 0 access-list dmz_nat0_outbound
nat (dmz) 10 0.0.0.0 0.0.0.0
static (inside,outside) 76.244.75.62 192.168.100.25 netmask 255.255.255.255 dns
static (dmz,outside) 76.244.75.61 192.168.9.123 netmask 255.255.255.255 dns
static (dmz,outside) 76.244.75.59 192.168.9.124 netmask 255.255.255.255 dns
static (dmz,outside) 76.244.75.58 192.168.9.4 netmask 255.255.255.255 dns
static (inside,dmz) 192.168.100.0 192.168.100.0 netmask 255.255.255.0
static (dmz,outside) 76.244.75.60 192.168.9.10 netmask 255.255.255.255 dns
static (inside,outside_cable) 50.84.96.183 192.168.100.25 netmask 255.255.255.255 dns
static (dmz,outside_cable) 50.84.96.182 192.168.9.123 netmask 255.255.255.255 dns
static (dmz,outside_cable) 50.84.96.180 192.168.9.124 netmask 255.255.255.255 dns
static (dmz,outside_cable) 50.84.96.179 192.168.9.4 netmask 255.255.255.255 dns
static (dmz,outside_cable) 50.84.96.181 192.168.9.10 netmask 255.255.255.255 dns
access-group outside_access_in in interface outside
access-group dmz_access_in in interface dmz
access-group outside_cable_access_in in interface outside_cable
route outside_cable 0.0.0.0 0.0.0.0 50.84.96.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
http 192.168.100.0 255.255.255.0 inside
http 204.107.173.0 255.255.255.0 outside
http 204.107.173.0 255.255.255.0 outside_cable
http 0.0.0.0 0.0.0.0 outside_cable
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_cable_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_cable_map interface outside_cable
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto isakmp enable inside
crypto isakmp enable outside
crypto isakmp enable outside_cable
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
telnet 192.168.100.0 255.255.255.0 inside
telnet timeout 5
ssh 192.168.100.0 255.255.255.0 inside
ssh 204.107.173.0 255.255.255.0 outside
ssh 204.107.173.0 255.255.255.0 outside_cable
ssh 0.0.0.0 0.0.0.0 outside_cable
ssh timeout 15
console timeout 0
vpdn group dataDSL request dialout pppoe
vpdn group dataDSL localname [email protected]
vpdn group dataDSL ppp authentication pap
vpdn username [email protected] password *********
dhcpd address 192.168.100.30-192.168.100.99 inside
dhcpd dns 192.168.100.5 68.94.156.1 interface inside
threat-detection basic-threat
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.100.5
vpn-tunnel-protocol IPSec l2tp-ipsec
group-policy cad_supplies_RAVPN internal
group-policy cad_supplies_RAVPN attributes
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value cad_supplies_RAVPN_splitTunnelAcl
group-policy VPNPHONE internal
group-policy VPNPHONE attributes
dns-server value 192.168.100.5
vpn-tunnel-protocol IPSec
split-tunnel-policy excludespecified
split-tunnel-network-list value Local_LAN_Access
client-firewall none
client-access-rule none
username swinc password BlhBNWfh7XoeHcQC encrypted
username swinc attributes
vpn-group-policy cad_supplies_RAVPN
username meredithp password L3lRjzwb7TnwOyZ1 encrypted
username meredithp attributes
vpn-group-policy cad_supplies_RAVPN
service-type remote-access
username ipphone1 password LOjpmeIOshVdCSOU encrypted privilege 0
username ipphone1 attributes
vpn-group-policy VPNPHONE
username ipphone2 password LOjpmeIOshVdCSOU encrypted privilege 0
username ipphone2 attributes
vpn-group-policy VPNPHONE
username ipphone3 password LOjpmeIOshVdCSOU encrypted privilege 0
username ipphone3 attributes
vpn-group-policy VPNPHONE
username oethera password WKJxJq7L6wmktFNt encrypted
username oethera attributes
vpn-group-policy cad_supplies_RAVPN
service-type remote-access
username markh password nqH+bk6vj0fR83ai0SAxkg== nt-encrypted
username markh attributes
vpn-group-policy cad_supplies_RAVPN
tunnel-group DefaultRAGroup general-attributes
default-group-policy DefaultRAGroup
tunnel-group DefaultRAGroup ipsec-attributes
pre-shared-key *
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
tunnel-group cad_supplies_RAVPN type remote-access
tunnel-group cad_supplies_RAVPN general-attributes
address-pool VPN_IP_range
default-group-policy cad_supplies_RAVPN
tunnel-group cad_supplies_RAVPN ipsec-attributes
pre-shared-key *
tunnel-group VPNPHONE type remote-access
tunnel-group VPNPHONE general-attributes
address-pool VPN_Phone
default-group-policy VPNPHONE
tunnel-group VPNPHONE ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 1500
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:8b25ecc61861a2baa6d2556a3679cc7c
: end

Hi,
You have your "group-policy" set so that you have excluding some networks from being tunneled.
In this access-list named Local_LAN_Access you specify "0.0.0.0"
Doesnt this mean you are excluding all networks from being tunneled? In other words no traffic goes to your tunnel.
This access-list should only contain your local LAN network from where you are connecting with the VPN Client. If you dont need to access anything on your local LAN while having the VPN on, you don't even need this setting on. You could just tunnel all traffic instead of excluding some networks.
- Jouni

ASA 5505 VPN clients can't ping router or other clients on network

I have a ASA5505 and it has a vpn set up. The VPN user connects using the Cisco VPN client. They can connect fine (the get an ip address from the ASA), but they can't ping the asa or any clients on the network. Here is the running config:
Result of the command: "show running-config"
: Saved
ASA Version 7.2(4)
hostname ASA
domain-name default.domain.invalid
enable password kdnFT44SJ1UFX5Us encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 10.0.0.4 Server
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
clock timezone MST -7
clock summer-time MDT recurring
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list vpn_splitTunnelAcl standard permit any
access-list inside_nat0_outbound extended permit ip any 10.0.0.192 255.255.255.192
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPNpool 10.0.0.220-10.0.0.240 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface smtp Server smtp netmask 255.255.255.255
static (inside,outside) tcp interface pop3 Server pop3 netmask 255.255.255.255
static (inside,outside) tcp interface www Server www netmask 255.255.255.255
static (inside,outside) tcp interface https Server https netmask 255.255.255.255
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
http server enable 480
http 10.0.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map outside_dyn_map 20 set pfs group1
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
group-policy vpn internal
group-policy vpn attributes
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpn_splitTunnelAcl
username admin password wwYXKJulWcFrrhXN encrypted privilege 15
username VPNuser password fRPIQoKPyxym36g7 encrypted privilege 15
username VPNuser attributes
vpn-group-policy vpn
tunnel-group vpn type ipsec-ra
tunnel-group vpn general-attributes
address-pool VPNpool
default-group-policy vpn
tunnel-group vpn ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:df7d1e4f34ee0e155cebe86465f367f5
: end
Any ideas what I need to add to get the vpn client to be able to ping the router and clients?
Thanks.

I tried that and it didn't work. As for upgrading the ASA version, I'd like to but this is an old router and I don't have a support contract with Cisco anymore, so I can't access the latest firmware.
here is the runnign config again:
Result of the command: "show startup-config"
: Saved
: Written by enable_15 at 01:48:37.789 MDT Wed Jun 20 2012
ASA Version 7.2(4)
hostname ASA
domain-name default.domain.invalid
enable password kdnFT44SJ1UFX5Us encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 10.0.0.4 Server
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
clock timezone MST -7
clock summer-time MDT recurring
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list vpn_splitTunnelAcl standard permit any
access-list inside_nat0_outbound extended permit ip any 10.0.0.192 255.255.255.192
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPNpool 10.0.0.220-10.0.0.240 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin
asdm location Server 255.255.255.255 inside
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface smtp Server smtp netmask 255.255.255.255
static (inside,outside) tcp interface pop3 Server pop3 netmask 255.255.255.255
static (inside,outside) tcp interface www Server www netmask 255.255.255.255
static (inside,outside) tcp interface https Server https netmask 255.255.255.255
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
http server enable 480
http 10.0.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map outside_dyn_map 20 set pfs group1
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
group-policy vpn internal
group-policy vpn attributes
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpn_splitTunnelAcl
username admin password wwYXKJulWcFrrhXN encrypted privilege 15
username VPNuser password fRPIQoKPyxym36g7 encrypted privilege 15
username VPNuser attributes
vpn-group-policy vpn
tunnel-group vpn type ipsec-ra
tunnel-group vpn general-attributes
address-pool VPNpool
default-group-policy vpn
tunnel-group vpn ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect icmp
service-policy global_policy global
prompt hostname context
Cryptochecksum:78864f4099f215f4ebdd710051bdb493

VPN client connect to CISCO 887 VPN Server bat they stop at router!!

Hi
my scenario is as follows
SERVER1 on lan (192.168.5.2/24)
|
|
CISCO-887 (192.168.5.4) with VPN server
|
|
INTERNET
|
|
VPN Cisco client on xp machine
My connection have public ip address assegned by ISP, after ppp login.
I've just configured (with Cisco Configuration Professional) the ADSL connection and VPN Server (Easy VPN).
All the PC on LAN surf internet and remote PC connect to VPN Cisco server via cisco VPN client.
But all remote PC after connection to Cisco VPN server don't ping SERVER1 in lan and therefore don't see SERVER1 and every other resource in LAN.
They can ping only router!!!
They are configured with Cisco VPN client (V5.0.007) with "Enabled Trasparent Tunnelling" and "IPSec over UDP NAT/PAT".
What is wrong in my attached configuration? (I've alspo tried to bind Virtual-Template1 both to unnambered Dialer0 and to Loopback0 but without luck)
Peraps ACL problem?
Building configuration...
Current configuration : 5019 bytes
! Last configuration change at 05:20:37 UTC Tue Apr 24 2012 by adm
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname gate
boot-start-marker
boot-end-marker
no logging buffered
aaa new-model
aaa authentication login default local
aaa authentication login ciscocp_vpn_xauth_ml_1 local
aaa authentication login ciscocp_vpn_xauth_ml_2 local
aaa authorization exec default local
aaa authorization network ciscocp_vpn_group_ml_1 local
aaa authorization network ciscocp_vpn_group_ml_2 local
aaa session-id common
memory-size iomem 10
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-453216506
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-453216506
revocation-check none
rsakeypair TP-self-signed-453216506
crypto pki certificate chain TP-self-signed-453216506
certificate self-signed 01
        quit
ip name-server 212.216.112.222
ip cef
no ipv6 cef
password encryption aes
license udi pid CISCO887VA-K9 sn ********
username adm privilege 15 secret 5 *****************
username user1 secret 5 ******************
controller VDSL 0
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp client configuration group EXTERNALS
key 6 *********\*******
dns 192.168.5.2
wins 192.168.5.2
domain domain.local
pool SDM_POOL_1
save-password
crypto isakmp profile ciscocp-ike-profile-1
   match identity group EXTERNALS
   client authentication list ciscocp_vpn_xauth_ml_2
   isakmp authorization list ciscocp_vpn_group_ml_2
   client configuration address respond
   virtual-template 1
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA1 esp-3des esp-sha-hmac
crypto ipsec profile CiscoCP_Profile1
set transform-set ESP-3DES-SHA1
set isakmp-profile ciscocp-ike-profile-1
interface Loopback0
ip address 10.10.10.10 255.255.255.0
interface Ethernet0
no ip address
shutdown
interface ATM0
no ip address
no atm ilmi-keepalive
interface ATM0.1 point-to-point
pvc 8/35
encapsulation aal5snap
protocol ppp dialer
dialer pool-member 1
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
no ip address
interface Virtual-Template1 type tunnel
ip unnumbered Dialer0
tunnel mode ipsec ipv4
tunnel protection ipsec profile CiscoCP_Profile1
interface Vlan1
ip address 192.168.5.4 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly in
interface Dialer0
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname ******@*******.****
ppp chap password 0 alicenewag
ppp pap sent-username ******@*******.**** password 0 *********
ip local pool SDM_POOL_1 192.168.5.20 192.168.5.50
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 600 life 86400 requests 10000
ip nat inside source list 1 interface Dialer0 overload
ip route 0.0.0.0 0.0.0.0 Dialer0
access-list 1 remark INSIDE_IF=Vlan1
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 192.168.5.0 0.0.0.255
access-list 100 remark CCP_ACL Category=4
access-list 100 permit ip 192.168.5.0 0.0.0.255 any
dialer-list 1 protocol ip permit
line con 0
line aux 0
line vty 0 4
transport input all
end

Hello,
Your pool of VPN addresses is overlapping with the interface vlan1.
Since proxy-arp is disabled on that interface, it will never work
2 solutions
1- Pool uses a different network than 192.168.5
2- Enable ip proxy-arp on interface vlan1
Cheers,
Olivier

VPN client connect to CISCO 887 VPN Server but I can't ping Local LAN

Hi
my scenario is as follows
SERVER1 on lan (192.168.1.4)
|
|
CISCO-887 (192.168.1.254)
|
|
INTERNET
|
|
VPN Cisco client on windows 7 machine
My connection have public ip address assegned by ISP, after ppp login.
I've just configured (with Cisco Configuration Professional) the ADSL connection and VPN Server (Easy VPN).
All the PC on LAN surf internet and remote PC connect to VPN Cisco server via cisco VPN client.
But all remote PC after connection to Cisco VPN server don't ping SERVER1 in lan and therefore don't see SERVER1 and every other resource in LAN. I can't even ping the gateway 192.168.1.254
I'm using Cisco VPN client (V5.0.07) with "IPSec over UDP NAT/PAT".
What is wrong in my attached configuration? (I've alspo tried to bind Virtual-Template1 both to unnambered Dialer0 and to Loopback0 but without luck)
Perhaps ACL problem?
Building configuration...
Current configuration : 4921 bytes
! Last configuration change at 14:33:06 UTC Sun Jan 26 2014 by NetasTest
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname TestLab
boot-start-marker
boot-end-marker
enable secret 4 5ioUNqNjoCPaFZIVNAyYuHFA2e9v8Ivuc7a7UlyQ3Zw
aaa new-model
aaa authentication login default local
aaa authentication login ciscocp_vpn_xauth_ml_1 local
aaa authentication login ciscocp_vpn_xauth_ml_2 local
aaa authorization exec default local
aaa authorization network ciscocp_vpn_group_ml_1 local
aaa authorization network ciscocp_vpn_group_ml_2 local
aaa session-id common
memory-size iomem 10
crypto pki trustpoint TP-self-signed-3013130599
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3013130599
revocation-check none
rsakeypair TP-self-signed-3013130599
crypto pki certificate chain TP-self-signed-3013130599
certificate self-signed 01
3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 33303133 31333035 3939301E 170D3134 30313236 31333333
35305A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D33 30313331
33303539 3930819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100A873 940DE7B9 112D7C1E CEF53553 ED09B479 24721449 DBD6F559 1B9702B7
9087E94B 50CBB29F 6FE9C3EC A244357F 287E932F 4AB30518 08C2EAC1 1DF0C521
8D0931F7 6E7F7511 7A66FBF1 A355BB2A 26DAD318 5A5A7B0D A261EE22 1FB70FD1
C20F1073 BF055A86 D621F905 E96BD966 A4E87C95 8222F1EE C3627B9A B5963DCE
AE7F0203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603
551D2304 18301680 14E37481 4AAFF252 197AC35C A6C1E8E1 E9DF5B35 27301D06
03551D0E 04160414 E374814A AFF25219 7AC35CA6 C1E8E1E9 DF5B3527 300D0609
2A864886 F70D0101 05050003 81810082 FEE61317 43C08637 F840D6F8 E8FA11D5
AA5E49D4 BA720ECB 534D1D6B 1A912547 59FED1B1 2B68296C A28F1CD7 FB697048
B7BF52B8 08827BC6 20B7EA59 E029D785 2E9E11DB 8EAF8FB4 D821C7F5 1AB39B0D
B599ECC1 F38B733A 5E46FFA8 F0920CD8 DBD0984F 2A05B7A0 478A1FC5 952B0DCC
CBB28E7A E91A090D 53DAD1A0 3F66A3
quit
no ip domain lookup
ip cef
no ipv6 cef
license udi pid CISCO887VA-K9 sn ***********
username ******* secret 4 5ioUNqNjoCPaFZIVNAyYuHFA2e9v8Ivuc7a7UlyQ3Zw
username ******* secret 4 Qf/16YMe96arcCpYI46YRa.3.7HcUGTBeJB3ZyRxMtE
controller VDSL 0
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp client configuration group EXTERNALS
key NetasTest
dns 8.8.4.4
pool VPN-Pool
acl 120
crypto isakmp profile ciscocp-ike-profile-1
match identity group EXTERNALS
client authentication list ciscocp_vpn_xauth_ml_2
isakmp authorization list ciscocp_vpn_group_ml_2
client configuration address respond
virtual-template 1
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
mode tunnel
crypto ipsec transform-set ESP-3DES-SHA1 esp-3des esp-sha-hmac
mode tunnel
crypto ipsec profile CiscoCP_Profile1
set transform-set ESP-3DES-SHA1
set isakmp-profile ciscocp-ike-profile-1
interface Ethernet0
no ip address
shutdown
interface ATM0
no ip address
no atm ilmi-keepalive
hold-queue 224 in
pvc 8/35
pppoe-client dial-pool-number 1
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
no ip address
interface Virtual-Template1 type tunnel
ip address 192.168.2.1 255.255.255.0
tunnel mode ipsec ipv4
tunnel protection ipsec profile CiscoCP_Profile1
interface Vlan1
ip address 192.168.1.254 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1452
interface Dialer0
ip address negotiated
ip mtu 1452
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname ****
ppp chap password 0 *********
ppp pap sent-username ****** password 0 *******
no cdp enable
ip local pool VPN-Pool 192.168.2.210 192.168.2.215
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 600 life 86400 requests 10000
ip nat inside source list 100 interface Dialer0 overload
ip route 0.0.0.0 0.0.0.0 Dialer0
access-list 100 remark
access-list 100 deny ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255
access-list 100 remark
access-list 100 permit ip 192.168.1.0 0.0.0.255 any
access-list 120 remark
access-list 120 permit ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255
line con 0
exec-timeout 5 30
password ******
no modem enable
line aux 0
line vty 0 4
password ******
transport input all
end
Best Regards,

I've updated ios to c870-advipservicesk9-mz.124-24.T8.bin and tried to ping from rv320 to 871 and vice versa. Ping stil not working.
router#sh crypto session detail
Crypto session current status
Code: C - IKE Configuration mode, D - Dead Peer Detection
K - Keepalives, N - NAT-traversal, T - cTCP encapsulation
X - IKE Extended Authentication, F - IKE Fragmentation
Interface: Dialer0
Uptime: 00:40:37
Session status: UP-ACTIVE
Peer: 93.190.178.205 port 500 fvrf: (none) ivrf: (none)
Phase1_id: 192.168.1.100
Desc: (none)
IKE SA: local 93.190.177.103/500 remote 93.190.178.205/500 Active
Capabilities:(none) connid:2001 lifetime:07:19:22
IPSEC FLOW: permit ip 10.1.1.0/255.255.255.0 10.1.2.0/255.255.255.0
Active SAs: 4, origin: dynamic crypto map
Inbound: #pkts dec'ed 0 drop 30 life (KB/Sec) 4500544/1162
Outbound: #pkts enc'ed 5 drop 0 life (KB/Sec) 4500549/1162

Server 2003 VPN clients can't verify username and password

Hi,
Hoping someone can help or point me in the right direction. I have a Windows Server 2003 R2 standard SP2 running RRAS. It has Dual NIC's and is configured for PPTP VPN. I am using a BT Business Hub 5 for internet access and using the BT Static IP service.
The BT Hub assigns the static IP address chosen to the Server using DHCP. The firewall is configured to port forward PPTP traffic to the 2003 server. This all works correctly.
The 2003 server is on a domain where the DC is a 2008 R2 server. The DC also acts as the DNS and DHCP for the network.
The default gateway for the domain is pointed towards our WinGate proxy server which also acts as a DNS server.
The 2003 server LAN NIC is configured manually, usually I would not configure a deafult gateway on the LAN NIC as the WAN NIC needs the default gateway for the BT Hub.
The problem I am having is if a default gateway is configured on the LAN NIC, I can connect to the VPN and it will logon to the network. Once connected everything works ok. If the connection drops, when trying to reconnect the client can no longer verify
the user name and password against the domain and the connection is refused.
If I do not have a default gateway configured in the LAN NIC the VPN clients can not verify the username and password for the domain at all and I get RPC failure errors in the event viewer with the source dnsapi.
Once this error occurs the only way I can get the clients to reconnect is to disable the WAN NIC, restart the RRAS service and enable the WAN NIC again.
Any insight will be much appreciated.

Hello,
for Networking configuration questions better ask in
http://social.technet.microsoft.com/Forums/windowsserver/en-US/home#forum=winserverNIS&filter=alltypes&sort=lastpostdesc&content=Search
Best regards
Meinolf Weber
MVP, MCP, MCTS
Microsoft MVP - Directory Services
My Blog: http://blogs.msmvps.com/MWeber
Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights.
Twitter:

IPSEC VPN clients can't reach internal nor external resources

Hi!
At the moment running ASA 8.3, with fairly much experience of ASA 8.0-8.2, I can't get the NAT right for the VPN clients.
Im pretty sure it's not ACL's, although I might be wrong.
The problem is both VPN users can reach internal resources, and vpn users cant reach external resources.
# Issue 1.
IPSEC VPN client cannot reach any local (inside) resources. All interfaces are pretty much allow any any, I suspect it has to do with NAT.
When trying to access an external resource, the "translate_hits" below are changed:
Auto NAT Policies (Section 2)
1 (outside) to (outside) source dynamic vpn_nat interface
   translate_hits = 37, untranslate_hits = 11
When trying to reach a local resource (10.0.0.0/24), the translate hits below are changed:
5 (inside) to (outside) source static any any destination static NETWORK_OBJ_172.16.32.0_24 NETWORK_OBJ_172.16.32.0_24
    translate_hits = 31, untranslate_hits = 32
Most NAT, some sensitive data cut:
Manual NAT Policies (Section 1)
<snip>
3 (inside) to (server) source static NETWORK_OBJ_1.2.3.0_29 NETWORK_OBJ_1.2.3.0_29
    translate_hits = 0, untranslate_hits = 0
4 (inside) to (server) source static any any destination static NETWORK_OBJ_10.0.0.240_28 NETWORK_OBJ_10.0.0.240_28
    translate_hits = 0, untranslate_hits = 0
5 (inside) to (outside) source static any any destination static NETWORK_OBJ_172.16.32.0_24 NETWORK_OBJ_172.16.32.0_24
    translate_hits = 22, untranslate_hits = 23
Auto NAT Policies (Section 2)
1 (outside) to (outside) source dynamic vpn_nat interface
    translate_hits = 37, untranslate_hits = 6
Manual NAT Policies (Section 3)
1 (something_free) to (something_outside) source dynamic any interface
    translate_hits = 0, untranslate_hits = 0
2 (something_something) to (something_outside) source dynamic any interface
    translate_hits = 0, untranslate_hits = 0
3 (inside) to (outside) source dynamic any interface
    translate_hits = 5402387, untranslate_hits = 1519419
## Issue 2, vpn user cannot access anything on internet
asa# packet-tracer input outside tcp 172.16.32.1 12345 1.2.3.4 443
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
MAC Access list
Phase: 2
Type: ACCESS-LIST
Subtype:
Result: DROP
Config:
Implicit Rule
Additional Information:
Result:
input-interface: outside
input-status: up
input-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule
Relevant configuration snippet:
interface Vlan2
nameif outside
security-level 0
ip address 1.2.3.2 255.255.255.248
interface Vlan3
nameif inside
security-level 100
ip address 10.0.0.5 255.255.255.0
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object network anywhere
subnet 0.0.0.0 0.0.0.0
object network something_free
subnet 10.0.100.0 255.255.255.0
object network something_member
subnet 10.0.101.0 255.255.255.0
object network obj-ipsecvpn
subnet 172.16.31.0 255.255.255.0
object network allvpnnet
subnet 172.16.32.0 255.255.255.0
object network OFFICE-NET
subnet 10.0.0.0 255.255.255.0
object network vpn_nat
subnet 172.16.32.0 255.255.255.0
object-group network the_office
network-object 10.0.0.0 255.255.255.0
access-list VPN-TO-OFFICE-NET standard permit 10.0.0.0 255.255.255.0
ip local pool ipsecvpnpool 172.16.32.0-172.16.32.255 mask 255.255.255.0
ip local pool vpnpool 172.16.31.1-172.16.31.255 mask 255.255.255.0
nat (inside,server) source static NETWORK_OBJ_1.2.3.0_29 NETWORK_OBJ_1.2.3.0_29
nat (inside,server) source static any any destination static NETWORK_OBJ_10.0.0.240_28 NETWORK_OBJ_10.0.0.240_28
nat (inside,outside) source static any any destination static NETWORK_OBJ_172.16.32.0_24 NETWORK_OBJ_172.16.32.0_24
object network vpn_nat
nat (outside,outside) dynamic interface
nat (some_free,some_outside) after-auto source dynamic any interface
nat (some_member,some_outside) after-auto source dynamic any interface
nat (inside,outside) after-auto source dynamic any interface
group-policy companyusers attributes
dns-server value 8.8.8.8 8.8.4.4
vpn-tunnel-protocol IPSec
default-domain value company.net
tunnel-group companyusers type remote-access
tunnel-group companyusers general-attributes
address-pool ipsecvpnpool
default-group-policy companyusers
tunnel-group companyusers ipsec-attributes
pre-shared-key *****

Hi,
I don't seem to get a reply from 8.8.8.8 no, kind of hard to tell as it's an iphone. To me, all these logs simply says it works like a charm, but still I can get no reply on the phone.
asa# ICMP echo request from outside:172.16.32.1 to outside:4.2.2.2 ID=6912 seq=0 len=28
ICMP echo request translating outside:172.16.32.1/6912 to outside:x.x.37.149/46012
ICMP echo reply from outside:4.2.2.2 to outside:x.x.37.149 ID=46012 seq=0 len=28
ICMP echo reply untranslating outside:x.x.37.149/46012 to outside:172.16.32.1/6912
ICMP echo request from outside:172.16.32.1 to outside:4.2.2.2 ID=6912 seq=256 len=28
ICMP echo request translating outside:172.16.32.1/6912 to outside:x.x.37.149/46012
ICMP echo reply from outside:4.2.2.2 to outside:x.x.37.149 ID=46012 seq=256 len=28
ICMP echo reply untranslating outside:x.x.37.149/46012 to outside:172.16.32.1/6912
ICMP echo request from outside:172.16.32.1 to outside:4.2.2.2 ID=6912 seq=512 len=28
ICMP echo request translating outside:172.16.32.1/6912 to outside:x.x.37.149/46012
ICMP echo reply from outside:4.2.2.2 to outside:x.x.37.149 ID=46012 seq=512 len=28
ICMP echo reply untranslating outside:x.x.37.149/46012 to outside:172.16.32.1/6912
asa# show capture capo
12 packets captured
   1: 08:11:59.097590 802.1Q vlan#2 P0 x.x.37.149 > 4.2.2.2: icmp: echo request
   2: 08:11:59.127129 802.1Q vlan#2 P0 4.2.2.2 > x.x.37.149: icmp: echo reply
   3: 08:12:00.103876 802.1Q vlan#2 P0 x.x.37.149 > 4.2.2.2: icmp: echo request
   4: 08:12:00.133293 802.1Q vlan#2 P0 4.2.2.2 > x.x.37.149: icmp: echo reply
   5: 08:12:01.099253 802.1Q vlan#2 P0 x.x.37.149 > 4.2.2.2: icmp: echo request
   6: 08:12:01.127572 802.1Q vlan#2 P0 4.2.2.2 > x.x.37.149: icmp: echo reply
   7: 08:12:52.954464 802.1Q vlan#2 P0 x.x.37.149 > 4.2.2.2: icmp: echo request
   8: 08:12:52.983866 802.1Q vlan#2 P0 4.2.2.2 > x.x.37.149: icmp: echo reply
   9: 08:12:56.072811 802.1Q vlan#2 P0 x.x.37.149 > 4.2.2.2: icmp: echo request
10: 08:12:56.101007 802.1Q vlan#2 P0 4.2.2.2 > x.x.37.149: icmp: echo reply
11: 08:12:59.132897 802.1Q vlan#2 P0 x.x.37.149 > 4.2.2.2: icmp: echo request
12: 08:12:59.160941 802.1Q vlan#2 P0 4.2.2.2 > x.x.37.149: icmp: echo reply
asa# ICMP echo request from outside:172.16.32.1 to inside:10.0.0.72 ID=6912 seq=0 len=28
ICMP echo reply from inside:10.0.0.72 to outside:172.16.32.1 ID=6912 seq=0 len=28
ICMP echo request from outside:172.16.32.1 to inside:10.0.0.72 ID=6912 seq=256 len=28
ICMP echo reply from inside:10.0.0.72 to outside:172.16.32.1 ID=6912 seq=256 len=28
ICMP echo request from outside:172.16.32.1 to inside:10.0.0.72 ID=6912 seq=512 len=28
ICMP echo reply from inside:10.0.0.72 to outside:172.16.32.1 ID=6912 seq=512 len=28
ICMP echo request from outside:172.16.32.1 to inside:10.0.0.72 ID=6912 seq=768 len=28
ICMP echo reply from inside:10.0.0.72 to outside:172.16.32.1 ID=6912 seq=768 len=28
asa# show capture capi
8 packets captured
   1: 08:15:44.868653 802.1Q vlan#3 P0 172.16.32.1 > 10.0.0.72: icmp: echo request
   2: 08:15:44.966456 802.1Q vlan#3 P0 10.0.0.72 > 172.16.32.1: icmp: echo reply
   3: 08:15:47.930066 802.1Q vlan#3 P0 172.16.32.1 > 10.0.0.72: icmp: echo request
   4: 08:15:48.040082 802.1Q vlan#3 P0 10.0.0.72 > 172.16.32.1: icmp: echo reply
   5: 08:15:51.028654 802.1Q vlan#3 P0 172.16.32.1 > 10.0.0.72: icmp: echo request
   6: 08:15:51.110086 802.1Q vlan#3 P0 10.0.0.72 > 172.16.32.1: icmp: echo reply
   7: 08:15:54.076534 802.1Q vlan#3 P0 172.16.32.1 > 10.0.0.72: icmp: echo request
   8: 08:15:54.231250 802.1Q vlan#3 P0 10.0.0.72 > 172.16.32.1: icmp: echo reply
Packet-capture.
Phase: 1
Type: CAPTURE
Subtype:
Result: ALLOW
Config:
Additional Information:
MAC Access list
Phase: 2
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
MAC Access list
Phase: 3
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   172.16.32.1     255.255.255.255 outside
Phase: 4
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group inside_access_in in interface inside
access-list inside_access_in extended permit ip any any log
Additional Information:
Phase: 5
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 6
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
Additional Information:
Phase: 7
Type: DEBUG-ICMP
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 8
Type: NAT
Subtype:
Result: ALLOW
Config:
nat (inside,outside) source static any any destination static NETWORK_OBJ_172.16.32.0_24 NETWORK_OBJ_172.16.32.0_24
Additional Information:
Static translate 10.0.0.72/0 to 10.0.0.72/0
Phase: 9
Type: HOST-LIMIT
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 10
Type: VPN
Subtype: encrypt
Result: ALLOW
Config:
Additional Information:
Phase: 11
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group outside_access_out out interface outside
access-list outside_access_out extended permit ip any any log
Additional Information:
Phase: 12
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 5725528, packet dispatched to next module
Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: allow

VPN Client - Assigned wrong netmask?

Similar Messages

Maybe you are looking for