VPN doesn't work at build 10049

VPN has worked at previous builds but not anymore at build 10049.
When I choose VPN-network provider whole Settings-windows shuts down.

Hi fiantsirk，
There have been some known issues in Windows 10 build 10049:
No access to Internet Protocol (v4 or v6) in 10049
VPN configurations might be affected, folks here have found out some ways to make it work (3rd-party software related), you may check at :
https://social.technet.microsoft.com/Forums/en-US/261392a2-3914-4518-acb4-065a0a635f58/build-10049-breaks-openvpn-there-are-no-tapwindows-adapters-on-this-system?forum=WinPreview2014General
Best regards
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Similar Messages

VPN doesn't work

I just switched from Cable Internet to Verizon high speed. Internet and e-mail work fine, but my Cisco VPN doesn't work with Verizon.
Thus I can't connect to my servers at work.
I know my VPN works good because I travel alot and it works in every hotel I stay at, in fact I just tried it down the street through WiFi.
Does anyone know the fix for this?

Easy solution......
Bridge mode is achieved by 2 easy steps:
1) - Log into the GUI
click the My Network Icon on top
Click Network Connections on the left
Click on the words "Broadband Connection (DSL)"
Make the Protocol dropdown say "Bridge"
Make the Bridge Mode dropdown say "Bridge"
Save - the unit will reset
2) Log back into the GUI
Click the My Network icon on top
Click Network Connections on the left
Click the on the word "LAN"
Remove the top checkmark (you want to not enable the DHCP Server)
Make sure the modems ip address is not going to be the same of your router
Save
Exit the GUI
I made my modem 192.168.10.1, and my routers lan network is 192.168.0.1
The 6100F is bridged. The internet light will stay out. Whatever the next device on the network is will need to do the PPPoE connection (with your ISP username and password) ex your router
Myk

My VPN doesn't work ever since I upgraded to iOS7

My VPN doesn't work ever since I upgraded to iOS7, pls help?

It's been a problem with ios 7, for now try using your apple id for it. Apple is supposed to be putting out a fix for it soon.

Application doesn't work after build

hi,
My program doesn't work while running the.exe.It works fine in Labview develop enviroment but it fails running when i do the same in .exe . If i run my .exe file ,i will get always error like below (see attch..).i am using Driver for Spectrum Analyzer(R&S,FSP). can anyone please suggest me?
Attachments:
Fehler.jpg ‏235 KB

Hi all,
I have the similar problem, I have a write a code to control power supplies for example Töllner 8852 and Töllner 8952
everything works fine in development version, but when I build a exe, named Teststand.exe
this freezes, and don`t work at all.
i tried to bug the exe, but in debug mode i only see, that beginnig from Device OK subvi nothing work anymore,
the dataflow seems to be stopped before Device OK subvi (see attached jpeg file)
i attach my build properties also.
I tried to run the exe on the development machine, where Labview runtime engine 2010, and VISA Run Time 5.2 installed.
The communication with the instrument(s) is over GPIB, i have a USB-GPIB adapter on my PC.
When i run the top level vi on the development machine in labview development version everything is working fine, but builded EXE doesn`t.
the pop up windows are for debugging purpose, the pop ups in Device OK subvi doesn`t appear by running the builded EXE
Labview version is 2010
could you please help me, what could be the reason, and what can i try next?
thank you in advance
best regards
Robert
Attachments:
Power Supply lvproj.jpg ‏177 KB
Modul Device OK.vi will not be loaded.jpg ‏89 KB
Test Power Supply simple.zip ‏59 KB

VPN doesn't work anymore after 10.6.2 update

Hello to all,
I've a MacPro with 10.6 SnowLeopard server, and until yesterday all was great with 10.6.1.
After update to 10.6.2 plus some airport update, VPN dooesn't work.
Could someone help me?
I use the firewall on Airport extreme (the latest model) and automatically forward VPn setting from SLServer Firewall.
Why it don't go anymore?
thank you to all for help
Marco
Italy

so, I'm trying from home to use VPN:
- if I try from usual user, doesn't work
- if I try from Server Administrator credentials (user + password) it works
Of course I need to use VPN from "normal" client users, not with Administrator credentials
Another strange issue is: in VPN netwotk configaration (client, preferences, network) if I put name and password about one user the 2 field become locked and I must erase that VPN connection and create it again.
If I put the administrator name+psw, the 2 field remaining accesible and unlocked.
I think in Apple they made a very bad job with 10.6.2 and VPN!
has someone any suggestion?
Marco

DragAcceptFiles Working in Windows 10 TP build 9926 But Not Working In build 10049 and build 10061

This is a cross post from
https://social.technet.microsoft.com/Forums/en-US/a63519d4-ba7a-46c1-bb34-ad034b836964/dragacceptfiles-working-in-9926-but-not-working-in-10049-and-10061?forum=WinPreview2014General. The moderator suggested I post this here:
My company has a software product that accepts dragged items. In all versions of Windows from XP through Windows 10 build 9926 that functionality has worked fine. However, with build 10049 (possibly 10041 which I did not test thoroughly before going
to 10049) and now 10061 that functionality stopped working. The application calls DragAcceptFiles to enable drag drop messages. In addition, either ChangeWindowMessageFilter is called on Vista or ChangeWindowMessageFilterEx is called on Windows
7 and higher for the messages WM_DROPFILES, WM_COPYDATA, and WM_COPYGLOBALDATA. This was working fine on Windows 10 build 9926. Now when I attempt to drag an item to our software product, I get the "Don't" symbol (circle with line through
it) and no WM_DROPFILES messages are received. The application is unchanged with only an upgrade to the Windows 10 build performed. As a sanity check, I created a brand new VM running build 9926 and the functionality worked fine. I then upgraded
the VM to 10049 and it stopped working. The following day I upgraded to 10061 and it is still broken. Is there are new filter or restriction in place since build 9926 on DragAcceptFiles that would be stopping the traditional drag drop procedure
from working? This is very frustrating because there is a dearth of information on Windows 10 API changes and since this appears to be some kind of recent change, I am out of ideas of where to look for answers. I can duplicate this problem on the older
platforms by simply calling DragAcceptFiles with the second parameter set to false. In that case, on Windows 7 for example, I will get the "Don't" symbol just I am getting now in the Windows 10 TP with the argument set to true.

DragAcceptFiles is now working again in 10074 so whatever the problem was, it has been fixed.

VPN doesn't work since I reset permissions

Hi .
Recently I reset my permissions via disk utility app, Since I did that, VPN doesn't connect on my mac. it works with same VPN information on my iPad & iPhone so the problem is not from VPN.
I'll be glad if you could help me.

Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem. Other users have had the same problem.
Apple Retail Store - Genius Bar

PPTP VPN doesn't work on iOS 6

I just tried to set up my iPad 2 (on iOS6) for an already working PPTP VPN server on my DD-WRT and found out that it doesn't work anymore (apparently somethings changed after iOS 4.3 according to tons of blogs on the net) There seems to be a few solutions about adding a couple entries to /tmp/pptpd/options.pptpd but none of these worked for me on iOS 6. Is there anyone knows a solution to this problem?
Note: nopcomp, noaccomp, default-asyncmap, mru 1400, mtu 1400 options do not work nor doesn't seem to help a bit at all, by looking at the dd-wrt log output. Most people claim these options make it work for iOS 5, but didn't work for me.

Yeah, resurrecting old thread here...
I was having similar problems with iOS6 and my DDWRT running on Buffalo WZR-600DHP. After I changed the mtu & mru to 1400, it worked. It was driving me nuts before.

Changed the Shared Secret, and now VPN doesn't work...

Hello all. So our VPN was working fine. I changed the Shared Secret, and it stopped working. Seems like any Shared Secret now that I use doesn't work, and I've been triple-checking it on both the server and clients to make certain that it's not miss-typed.
It seems to connect OK, but then it fails to authorize. I've got the proper ports open, and again, it worked just fine with the first Shared Secret I used.
Is there something I'm missing about Shared Secrets here? You should be able to change them when you need too, right?
Message was edited by: Jeffrey McGrew

Looking at the logs I'm seeing something strange that I don't understand. It appears that one part of the authorization is succeeding, and another part failing:
"DSAuth plugin: Could not authenticate key agent for encryption key retrieval."
Then, two lines later:
"CHAP peer authentication succeeded for USER"
"DSAccessControl plugin: User 'USER' authorized for access"
But then the client never shows that it's authorized. So is this a problem with the client configuration, since the server is showing an authorized session starting, or is there something wrong with the DSAuth Plugin?
(going to read more PDFs)

Client VPN doesn't work until reload; all other services are fine

We have a 1800 router running 12.4.x that is acting up. Every week or 2, client vpn connectivity stops working on it (clients receive a ' reason 412; the remote peer is no longer responding' when trying to connect). All other traffic running through that router continues to work fine (site to site, nat, etc). If we run a 'clear ip nat translation', then ONE client can reconnect, but any subsequent clients cannot. So, basically one at a time. the only 'fix' is a reboot of the router. any suggestions on where to start troubleshooting?
thanks!

Matt,
Did you disable NAT-T on this device?
http://www.cisco.com/en/US/products/ps6120/products_tech_note09186a00807e0aca.shtml#solution01
Thanks,
Tarik Admani
*Please rate helpful posts*

Application doesn't work after build (database toolkit and report gen toolkit).

I wrote an application using database toolkit and report gen toolkit to retrieve some data from a database, put into a Word doc, save the Word doc and print it. It works fine when I run the vi, but when I build and run it, it does nothing. I have tried all of the settings in Projec Manager that I think might help but it still won't work right. Labview 8.2.1, XP.
Thanks,
Charlie
Solved!
Go to Solution.

Thanks for the help. I finally abondened the Word append table and used the regular report gen append table and got it to work fine. The error was 214682314. That led me to the thread about column numbers must vbe between 1 and 63, but like I said, my coulumn number is 7 so don't know what is going on. Anyway I got the vi to work and do what I want so I guess now the problem is solved (moot).
Charlie

Connection to VPN doesn't work with exclamation mark on Network symbol

Hello everyone,
I'm new to this forum and not really professional in VPN stuff, though I'm an experienced computer user and programmer. I'm using Cisco VPN
5.0.07.0440-k9-x64 from the Paul Scherrer Institute on Windows 8 64-bit. The program was working previously fine, but at some point, whenever I connect to VPN and login, I lose connection to the internet, and nothing related to my internet connection work, and I see an exclamation mark on the wireless network symbol. And when I disconnect the VPN, I get everything back to normal.
I got almost the same problem when I installed Kaspersky Internet Security due to some suspicion on security, but then I removed it and everything was back to normal. After that, the VPN worked for some time, and again didn't work anymore at some point. First thing I tried is disabling the Windows Firewall, and it didn't help.
My network adapter is: Qualcomm Atheros AR9002WB-1NG Wireless Network Adapter
In my network adapter, I can't change the TCP/IP v4 Configuration. When I double click, it says something like: "For the configuration of TCP/IP, there must be a network device installed and activated" (The sentence is translated from German, my Windows is German).
Is there like a "global reset" that would get the VPN to work again? What should I do?
Please advise, and if you require any piece of information, let me know.
Thank you.

I'm using now VPNC on linux. No more cisco! Crappy program and crappy support!

My VPN doesn't work.!!!

Hi All,
I configured a sample VPN in a 2611 Router to connect via Cisco VPN Client Sfw from a Remote PC on internet.
When the tunnel is estabilished, all networks stop to work in my PC.
I can't access the LAN inside.
Could anybody help me to solve this problem ?
Follow my config :
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
service linenumber
hostname mtech_lab_rt1
boot-start-marker
boot-end-marker
enable password xxx
no network-clock-participate slot 1
no network-clock-participate wic 0
aaa new-model
aaa authentication login LOCALUSERS local
aaa session-id common
ip subnet-zero
ip domain name xxx.com
ip cef
ip audit po max-events 100
username dticsco password 0 xxx
ip ssh time-out 60
ip ssh authentication-retries 2
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp client configuration group HOME
key xxx
dns 192.168.0.4
domain xxx.com
pool CLIENT_ADDRESSES
crypto ipsec transform-set MTECHVPN_SET esp-3des esp-sha-hmac
crypto dynamic-map CLIENT_MAP 1
set transform-set MTECHVPN_SET
reverse-route
crypto map MTECHVPN_VPN client authentication list LOCALUSERS
crypto map MTECHVPN_VPN isakmp authorization list LOCALUSERS
crypto map MTECHVPN_VPN client configuration address respond
crypto map MTECHVPN_VPN 100 ipsec-isakmp dynamic CLIENT_MAP
interface FastEthernet0/0
ip address 192.168.0.130 255.255.255.0
ip nat inside
duplex auto
speed auto
interface FastEthernet0/1
ip address 41.x.x.15 255.255.254.0
ip nat outside
duplex auto
speed auto
crypto map MTECHVPN_VPN
ip local pool CLIENT_ADDRESSES 192.168.2.1 192.168.2.10
ip nat inside source list NATLIST interface FastEthernet0/1 overload
ip nat inside source static tcp 192.168.0.6 25 41.x.x.15 25 extendable
ip nat inside source static tcp 192.168.0.6 110 41.X.X.15 110 extendable
ip http server
no ip http secure-server
ip classless
ip route 0.0.0.0 0.0.0.0 41.x.x.1
ip route 192.168.0.0 255.255.255.0 FastEthernet0/0
ip access-list standard NATLIST
permit 192.168.0.0 0.0.0.255
dial-peer cor custom
line con 0
location work
exec-timeout 30 30
password cisco
line aux 0
password cisco
line vty 0 4
login authentication LOCALUSERS
transport input ssh
end
Thanks
AB

version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
service linenumber
hostname mtech_lab_rt1
boot-start-marker
boot-end-marker
enable password MtechP@zz11E
no network-clock-participate slot 1
no network-clock-participate wic 0
aaa new-model
aaa authentication login USERAUTHEN local
aaa authorization network GROUPAUTHOR local
aaa session-id common
ip subnet-zero
ip domain name mydomain.com
ip cef
ip audit po max-events 100
username antonio password 0 tonhao01
username dticsco password 0 dt!czc0
username ricardo password 0 ric123
username belarmino password 0 bneves0511
ip ssh time-out 60
ip ssh authentication-retries 2
crypto isakmp policy 3
encr 3des
authentication pre-share
group 2
crypto isakmp client configuration group MTECHVPN
key Mdt@Vpn!zz030459
dns 192.168.0.4
wins 192.168.0.4
domain mydomain.com
pool ippool
acl 101
crypto ipsec transform-set myset esp-3des esp-md5-hmac
crypto dynamic-map dynmap 10
set transform-set myset
reverse-route
crypto map clientmap client authentication list USERAUTHEN
crypto map clientmap isakmp authorization list GROUPAUTHOR
crypto map clientmap client configuration address respond
crypto map clientmap 10 ipsec-isakmp dynamic dynmap
interface FastEthernet0/0
ip address 192.168.0.130 255.255.255.0
ip nat inside
duplex auto
speed auto
interface FastEthernet0/1
ip address 41.x.x.15 255.255.254.0
ip nat outside
duplex auto
speed auto
crypto map clientmap
ip local pool ippool 10.1.1.10 10.1.1.20
ip nat inside source list 111 interface FastEthernet0/1 overload
ip http server
no ip http secure-server
ip classless
ip route 0.0.0.0 0.0.0.0 41.x.x.1
access-list 101 permit ip 192.168.0.0 0.0.0.255 10.1.1.0 0.0.0.255
access-list 111 deny ip 192.168.0.0 0.0.0.255 10.1.1.0 0.0.0.255
access-list 111 permit ip any any
dial-peer cor custom
line con 0
location work
exec-timeout 30 30
password 7 02050D480809
line aux 0
password 7 0822455D0A16
line vty 0 4
login authentication USERAUTHEN
transport input ssh
end

Windows 10 Start menu not work in build 10049, restart take logn time

Same for me, I've started with win 8.1 updated to 10042, then to 10049. Menu start isnt working, and reboots take like 20 mins. Any fix?

Hi,
For Start Menu, please re-register it and test if it can make any difference, In the administrative
Windows PowerShell window, type the following command and hit Enter key:
Get-appxpackage -all *shellexperience* -packagetype bundle |% {add-appxpackage -register -disabledevelopmentmode ($_.installlocation + “\appxmetadata\appxbundlemanifest.xml”)}
Or I recommend you test whether this issue happens in another user account.
For the long reboot time, I recommend you keep latest Windows updates and drivers for all deivces, do sysytem maintance to improve the system performance, such as disk clean up, disable startup programs to decrease the reboot time, test whether issue persists.
Regards
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

VPN doesn,t work on WRT54GX-v2 either

Hi, I have exactly the same problem with my WRT54GX-v2 as other people had with there WRT54G v6 http://forums.linksys.com/linksys/board/message?board.id=Wireless_Routers&message.id=183
A new version seem to fix the problem, but I can't fine any update to my GX-version.
Have anyone succeed to have VPN working on WRT54GX model ?

hi , if you are facing issues with you VPN ,make sure that the "VPN passthrough" is enabled under the security page of the router.Access the setup using http://192.168.1.1 and enable VPN passthrough if disabled..
If this does not work you have have to forward the following ports on the router . 1723,500,50,43-47,445 .
On how to forward ports visit this link http://kb.linksys.com and look for answer ID 688

VPN doesn't work at build 10049

Similar Messages

Maybe you are looking for