VPN Woes with new AP unit

I bought a new Airport Extreme, hooked it up and was enjoying everything that was flawlessly running... Then we tried our vpns.
I ended up calling support to find out what I was doing wrong, and it tunes out that my purchase was the issue!
We have two types of vpns here, cisco and Nortel. The recomendation was to negate our NAT and place everything out in the DMZ. After I finished laughing, I regretably took my unit back.
Is there ANYONE that has a logical fix for this or recomendation... comments? I can see from oher posts that we are not alone here as far as getting propper vpn pass through on the new access point.
We really liked the unit, but can not live without our vpn connections...
Thanks

Still reading -- but these links are very useful:
Protocols supported by iOS:
http://support.apple.com/kb/HT1288
Setting up VPN (basic guide):
http://support.apple.com/kb/HT1424?viewlocale=en_US

Similar Messages

IPod Click Wheel (4th gen) won't work with new head unit

Hi all,
Not sure if this is the right forum but... I just put a new head unit in our 2000 Mazda Miata. It's a JVC Arsenal KD-A806. I have tried using the front and back USB ports to connect the iPod and all I get is "reading" over and over and then "not support" on the head unit display. And the "do not disconnect" on the iPod. I've tried different cables and I know the head unit is ok because my husband's Samsung MP3 player works just fine. Is there something with the iPod that might not be up to snuff? I've confirmed via iTunes I have the latest software v3.1.1. It has about 4,000 songs on it.
Thanks in advance - I haven't been able to find any resolution anywhere else.

Mean to say KD-A805 (not 6) and I just found a link saying that you can't connect my iPod to this unit via USB....

L2L VPN issues with new network

I've added a new network for a customer's firewall and I'm trying to get that network across the existing VPN tunnel to their DR site. The new network is 10.133.133.0/24 and I'm trying to get it to connect to 10.1.14.0/24 on the other side of the tunnel.
I'm missing something, though, because when I do a packet-tracer to simulate traffic, it dies before getting encrypted. The output is below.
What am I missing to get this traffic to even attempt to go across the tunnel?
4344-FWL001#packet-tracer input backup icmp 10.133.133.10 0 0 10.1.14.20
Phase: 1
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   0.0.0.0         0.0.0.0         outside
Phase: 2
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group backup_acl in interface backup
access-list backup_acl extended permit ip 10.133.133.0 255.255.255.0 10.1.14.0 255.255.255.0
Additional Information:
Phase: 3
Type: CONN-SETTINGS
Subtype:
Result: ALLOW
Config:
class-map class-default
match any
policy-map global_policy
class class-default
set connection decrement-ttl
service-policy global_policy global
Additional Information:
Phase: 4
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 5
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
Additional Information:
Phase: 6
Type: NAT-EXEMPT
Subtype:
Result: ALLOW
Config:
match ip backup 10.133.133.0 255.255.255.0 outside 10.1.14.0 255.255.255.0
    NAT exempt
    translate_hits = 40, untranslate_hits = 0
Additional Information:
Phase: 7
Type: NAT
Subtype:
Result: ALLOW
Config:
nat (backup) 1 0.0.0.0 0.0.0.0
match ip backup any outside any
    dynamic translation to pool 1 (216.211.133.59 [Interface PAT])
    translate_hits = 254, untranslate_hits = 18
Additional Information:
Phase: 8
Type: NAT
Subtype: host-limits
Result: ALLOW
Config:
nat (backup) 1 0.0.0.0 0.0.0.0
match ip backup any outside any
    dynamic translation to pool 1 (216.211.133.59 [Interface PAT])
    translate_hits = 254, untranslate_hits = 18
Additional Information:
Phase: 9
Type: VPN
Subtype: encrypt
Result: DROP
Config:
Additional Information:
Result:
input-interface: backup
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule

And what I get from isakmp debug:
Feb 28 13:41:26 [IKEv1]: Group = 216.203.46.252, IP = 216.203.46.252, QM FSM error (P2 struct &0xc9f39e68, mess id 0xe0ba04c)!
Feb 28 13:41:26 [IKEv1 DEBUG]: Group = 216.203.46.252, IP = 216.203.46.252, IKE QM Initiator FSM error history (struct &0xc9f39e68) , : QM_DONE, EV_ERROR-->QM_WAIT_MSG2, EV_TIMEOUT-->QM_WAIT_MSG2, NullEvent-->QM_SND_MSG1, EV_SND_MSG-->QM_SND_MSG1, EV_START_TMR-->QM_SND_MSG1, EV_RESEND_MSG-->QM_WAIT_MSG2, EV_TIMEOUT-->QM_WAIT_MSG2, NullEvent
Feb 28 13:41:26 [IKEv1 DEBUG]: Group = 216.203.46.252, IP = 216.203.46.252, sending delete/delete with reason message
Feb 28 13:41:26 [IKEv1 DEBUG]: Group = 216.203.46.252, IP = 216.203.46.252, constructing blank hash payload
Feb 28 13:41:26 [IKEv1 DEBUG]: Group = 216.203.46.252, IP = 216.203.46.252, constructing IPSec delete payload
Feb 28 13:41:26 [IKEv1 DEBUG]: Group = 216.203.46.252, IP = 216.203.46.252, constructing qm hash payload
Feb 28 13:41:26 [IKEv1]: IP = 216.203.46.252, IKE_DECODE SENDING Message (msgid=216bc3cb) with payloads : HDR + HASH (8) + DELETE (12) + NONE (0) total length : 68
Feb 28 13:41:26 [IKEv1 DEBUG]: Group = 216.203.46.252, IP = 216.203.46.252, IKE Deleting SA: Remote Proxy 10.1.14.0, Local Proxy 10.133.133.0
Feb 28 13:41:26 [IKEv1]: Group = 216.203.46.252, IP = 216.203.46.252, Removing peer from correlator table failed, no match!
Feb 28 13:41:26 [IKEv1 DEBUG]: Pitcher: received key delete msg, spi 0xb161983b
Feb 28 13:41:29 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 28 13:41:29 [IKEv1]: Group = 216.203.46.252, IP = 216.203.46.252, IKE Initiator: New Phase 2, Intf backup, IKE Peer 216.203.46.252 local Proxy Address 10.133.133.0, remote Proxy Address 10.1.14.0, Crypto map (outside_map)
Feb 28 13:41:29 [IKEv1 DEBUG]: Group = 216.203.46.252, IP = 216.203.46.252, Oakley begin quick mode
Feb 28 13:41:29 [IKEv1 DEBUG]: Group = 216.203.46.252, IP = 216.203.46.252, IKE got SPI from key engine: SPI = 0x9b973b9b
Feb 28 13:41:29 [IKEv1 DEBUG]: Group = 216.203.46.252, IP = 216.203.46.252, oakley constucting quick mode
Feb 28 13:41:29 [IKEv1 DEBUG]: Group = 216.203.46.252, IP = 216.203.46.252, constructing blank hash payload
Feb 28 13:41:29 [IKEv1 DEBUG]: Group = 216.203.46.252, IP = 216.203.46.252, constructing IPSec SA payload
Feb 28 13:41:29 [IKEv1 DEBUG]: Group = 216.203.46.252, IP = 216.203.46.252, constructing IPSec nonce payload
Feb 28 13:41:29 [IKEv1 DEBUG]: Group = 216.203.46.252, IP = 216.203.46.252, constructing proxy ID
Feb 28 13:41:29 [IKEv1 DEBUG]: Group = 216.203.46.252, IP = 216.203.46.252, Transmitting Proxy Id:
Local subnet: 10.133.133.0 mask 255.255.255.0 Protocol 0 Port 0
Remote subnet: 10.1.14.0 Mask 255.255.255.0 Protocol 0 Port 0
Feb 28 13:41:29 [IKEv1 DEBUG]: Group = 216.203.46.252, IP = 216.203.46.252, constructing qm hash payload
Feb 28 13:41:29 [IKEv1]: IP = 216.203.46.252, IKE_DECODE SENDING Message (msgid=150b2ab3) with payloads : HDR + HASH (8) + SA (1) + NONCE (10) + ID (5) + ID (5) + NONE (0) total length : 168
Feb 28 13:41:29 [IKEv1]: IP = 216.203.46.252, IKE_DECODE RECEIVED Message (msgid=cabc11c) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 224
Feb 28 13:41:29 [IKEv1 DEBUG]: Group = 216.203.46.252, IP = 216.203.46.252, processing hash payload
Feb 28 13:41:29 [IKEv1 DEBUG]: Group = 216.203.46.252, IP = 216.203.46.252, processing notify payload
Feb 28 13:41:29 [IKEv1]: Group = 216.203.46.252, IP = 216.203.46.252, Received non-routine Notify message: Invalid ID info (18)
I suspect the configs don't match on both sides, but getting info from the other side of the tunnel is like pulling teeth.

MSI K8N Diamond stable at 2800 for weeks, not now with new folding units

Hi chaps.
I have been running my Opteron 170 for 7 weeks now folding 24/7 without so much as a twitch.
However, since the new "5 way melt" work units have been issued it is almost impossible for either core to finish a unit...either that or the machine reboots randomly.
It re-gains stability ONLY if I run the CPU at 10x268MHz=2680 MHz
Other types of work units finish stably and very quickly still so no change there.
So I have to assume that the machine was never REALLY stable, despite lots of testing with OCCT and Memtest etc to the contrary.
Now does anyone know of any reason why the HT limit might be 268MHz?
I have tried 3 sets of different RAM, to the point where I am using a "fresh" set of OCZ PC4800 units at 2.85v ...and still getting the same problems.
I am beginning to suspect the motherboard, so if anyone has any advice, I would be glad to hear it.
Would the VRM circuitry be degrading already? All caps look like new and the Mobo/case temp is always lower than 25°C. Even the VRM heatsinks are only warm to the touch.
I gained no stability by raising the CPU voltage to 1.54v, it was still unstable when folding the same type of units.
so I have put it back to 1.4v+3.3%
BIOS 1.8/3.8 as in sig.
As I said, all other types of units complete very swiftly and without error,as does OCCT etc.
Any help would be appreciated.
Otherwise it is goodbye MSI and another board hits Ebay!
Regards and thanks
K6dude

Hi,
Well I have tried the 5.0a BIOS and no luck at all. It is even more unstable and will not work as well as the one that I have despite giving higher RAM volts.
I just downloaded a new version of A64 tweaker and happily found that this version (0.6 beta) has a different range of tweakable components. They now include Skew controls and drive strength. This is important, as most TCCD and TCC5 based ram runs faster with a "weak" drive strength rather than the default "strong" setting that the MSI BIOS defaults to.
This could help get better stability at higher clocks for some of us. Also, setting the Skew to 248 (max setting) can help a little....just like on the DFi boards...though their max settings exceed 255!
I ran my CPU and RAM in my friend's DFi Expert last weekend for a total of 2 days running all sorts of tests and benches. I got her stable at 3150MHz for at least 8 hours folding 2 independent work units (5 way melt units). voltage was 1.42v with the RAM at 315MHz (DDR630) 1:1 at 2.85v. CPU temp Maxed out at 41°C on air whilst folding
Sandra exceeded 28,500 on the CPU test and 7890 on the bandwidth and the thing really flew along. Memtest was stable over 1200% and Prime95 ran perfectly over several hours too...no crashes, CMOS resets/BSODs, lockups/shutdowns...nothing at all wrong. Even OCCT ran a successful test or two.
This was with my own CPU cooler and in the same case as mine.
Now I REALLY know what my CPU and RAM is capable of. I just need a capable BIOS to help me out with my MSI. I think realistically though, that I will have to admit defeat and be happy with 2810MHz on this board with a 183 divider for RAM.
Thanks for all your help guys...so very much appreciated. (aicjofs, you are a saint)
Meanwhile if anyone needs help here, I hope I can be of use to at least a few of you.
K6dude
PS Sorry to say that the Benches results are not saved as his rig was under construction and were lost as he reformatted with win64 before I could copy them to USB drive. I will duplicate the results as and when I can get a DFi board late summer.

Home Network Woes With New E2500

I replaced an EA1000 Wi-Fi router with a E2500, and my internet is faster, so that is a good thing. What's not-so-good is that my computers don't see each other on the network like they did before. I have 2 laptops running Windows 7 and a tablet running Windows 8.1. My main Win7 laptop does not see either of the other 2 PCs; The 2nd Win7 laptop may or may not see the other 2; and my Win8 tablet sees only the main Win7 laptop. I've gone through everything in all 3 PCs as far as Network and Sharing Center Settings. I've tried different security settings in the router setup. I would really like all 3 PCs to see each other like they did on the old router. Any suggestions on where to look, and what to look for?

Guest network is off. Both PCs that are here (1 is on a road trip) are connected to the 5 GHz band.
Both are set for Automatic IP Address.
To add to the mystery, my Dell tablet sees itself AND my Dell latop on the network, and can access files on the laptop, while the laptop itself does not even recognize itself as being on the network, i.e. when I click on network in Windows Explorer, nothing shows up. I would immediately suspect the Dell laptop as being the issue, since it doesn't even see itself on the network, except for that little fact that I can put the old router back online and each computer will see the others and they play happily together. This wackiness only happens on the new router.
Any other ideas? (and I do appreciate your help!)

Receiving Error : Please set the Receivables system options for this operating unit and ensure that the MO: Operating Unit profile option is correctly set with an operating unit that is set up in Receivables. while trying to create a new Customer.

Hi All,
We have set up a new Operating Unit in Oracle Apps. Now when I am trying to create a new Customer in that Operating Unit, I am receiving following error:
ERROR MESSAGE:-Please set the Receivables system options for this operating unit and ensure that the MO: Operating Unit profile option is correctly set with an operating unit that is set up in Receivables.
We do have MO: Operating Unit and MO: Default Operating Unit set properly at Responsibility level for the Responsibility through which I am accessing this form.
Your help is appreciated!
Thanks in advance,
SKA

You can refer this thread and check your MO operating unit is set or not https://community.oracle.com/message/3937028 thanks

PO with New unit of conversion

Hi,
We have the situation is PO is not update the new unit of measure conversion. As the PO was created with reference to the contract. The contract donu2019t have the unit of conversion. I know the PO is picking from the contract. Iam not able to change the contract with new unit of conversion. Pl advice how the PO will pick the new unit of conversion.
Regards,
Kumar

Hi
Thanks for the info.. i did the same but it taking unit conversion from the contract not from material master
Kumar

IPod Touch no longer working with car Head Unit since update

Hi there, I have a problem with using my iPod Touch with my car's head unit.
I've been using my iPod Touch with the Alpine IDA X001 Head unit fitted in my car for the last 3 months without any problems, however I installed the latest software update for the Touch (v4.0) and now the head unit connects and then says no USB device. At first I thought it was the cable as the cable supplied with the head unit is pretty fragile, so I've replaced it with a new one but it still doesn't work.
I've tested with my iPod Nano and it works perfectly so its not a problem with the head unit or lead (I plugged the Touch in and it didn't work, plugged the Nano in and worked perfectly and then plugged the Touch in and didn't work).
Can anyone help or is it gonna be a case of Restoring the iPod Touch back to factory settings ????

I was also having this problem with my Kenwood car stereo. I went into the store and they did a complete restore. I didn't think it worked but the next time I plugged it into my usb to connect with my car stereo it worked. So you might try doing a restore.

TS3899 Cannot send email with new iPad air. Works fine with old iPad and iPhone.

Cannot send email with new iPad air. Works fine with old iPad and iPhone. I have deleted account and reinstalled.

Thanks. I got the problem fixed. Spent time with the Apple folks and was kicked up to a senior advisor. It seems the problem was with my internet provider - Tmie Warner. Remember I could use the old ipad and the iphone to send mail. I checked all the specifics between the three units. It seems that TW is changing over from the RR.com to TWC.com. Since the new ipad air was just set up, it fell under the new TWC mail specifics.

Follow up material with different base unit of measure

Hi all,
I have the BOM with material Mat1 as a component. The base unit of measure of Mat1 is KG.
Is it possible to replace Mat1 with Mat 2 material in MRP once the Mat1 warehouse stock is depleted.
The base unit of measure of Mat 2 is KGK.
The required quantity of MAT1 should be recalculated from KG to KGK accordanly unit ratio.
Please, expain, where does it maintain?
Thanks,
Peter

Hello Peter,
You can use follow-up setting (set Mat2 as follow-up of Mat1 in MRP 4 view of material master if this follow-up scenario is valid for all BOM) with discontinuation indicator '1', w/o effective-out date. In this case Mat1's stock will run out (no PldOrd, PR, etc) will be created, and from the date, when Mat1's stock runs out, MRP will calculate with Mat2.
As I told you, according to my best knowledge, you cannot realize this with different base unit of measures. (you have to change the buom of one of the related material masters or create a new material master if you cannot cope with buom-change).
Follow-up group scenario can also be used but I guess different buoms will be a problem in that case as well.
Maybe there are better solution but I'm not aware of it...
BR
Csaba

Wifi problems with new ipad

I'm trying to learn how to correct wifi problems with new iPad. It is the wifi only, 64GB model. I want to be able to use it at work, where we have a great wifi network. I can usually connect to our network with no problem, but after an hour or so my iPad loses the network. When I try to reconnect, I see that the network is showing full strength reception, but I get the error message from the iPad that I am "Unable to join" the network. My iPhone connects to the same network seamlessly, as do all of the other iPhones of my co-workers and the older generation iPads that some of our staff has.
At other locations, I typically have no problems (home, apple store, etc.) but I have had the same situation pop up at a coffee shop where I could see that there was a wifi network available, but I could not join it even though it was the shop's free wifi.
I have tried turning the iPad off, turning off wifi and turning it back on again, and forgetting the wifi network in question. I can't think of any other methods that are available to an end user to correct the problem.
I have already gone to the Apple store to swap out the unit, and the newer one is having the same symptoms.
Can anyone offer any advice here? This is quite frustrating.

No problem! Have a read at this most interesting article which has special significance as regards your models!
http://edition.cnn.com/2012/04/05/tech/gaming-gadgets/ipad-wi-fi-issues/index.ht ml
However, I attach an extract from another thread for your perusal. You can disregard any suggestions/links you have already explored -
created by Texas Mac Man in Using iPad - View the full discussion
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
 Cheers, Tom ;)

How to link ECC Company code with BCS Consolidation unit

I have to create new consolidation unit in BCS, parallelly in SAP R/3 also I have created a company code.
I could read following in the forum :-
The Company Codes from ECC are assigned to the characteristic Company in BCS, thus creating a one to one relationship between ECC & BCS company codes.
BUT HOW TO DO THE SAME.
Also any advise on Profit centre and cost centre etc in BCS in line with ECC. This is first time I am configuring in BCS,

Typically in ECC company codes are assigned to a company. The company is typically used for cons unit in BCS, but it is not uncommon for company code to be used as cons unit.
When company code is used, it is an attribute of the characteristic company and thus in the load mapping, the company is mapped to the attribute company code. This results in company code being mapped to company.
Otherwise, if company code is in the databasis as the cons unit role, then it is simply mapped to company code to company code.
For profit center and cost center, these are typically assigned the role subassignment, but it is not uncommon for profit center to be a cons unit for a matrix consolidation. However, these characteristics must first be included in the totals/databasis infocube.

Instances not displaying in the workspace with new version

Platform: ALBPM 6.0.4 Enterprise StandAlone on AIX.
We had a project deployed and set up with users assigned to two different roles: analyst and support.
There were views that were associated with both roles that allowed them to see all completed instances or In process instances no matter who the instances were assigned to.
This version was 1.1.1 and everthing was working fine.
When a new project version was deployed the version number changed to 1.2.0.
People with the support role can not see the new instances created in the new version - even if they do a search.
People with only the analyst role can see all instances - old and new versions.
People with both roles can only see the old version, even if they do a search.
Any ideas?

We may have found the problem. The participant who was assgined to the Support role did not have the same organization as what was associated with the new version of the project when it was deployed. Also, the previous version of the project was not associated with any organizational unit. We added the organization unit to the participant and now it works.

New Operating Unit creation - GL or HRMS

Dears,
Please i ve a great doubt, please advice which is right approach....
Using General Ledger -Accounting Setup manager under Primary ledger there is a option to create new Operating unit by attaching LE and BG.
If i do so i get new OU and my other sub modules in Financials(AP,AR,CM.FA) are operational ...
using HRMS - organization i can designate any Company organization as Operating unit,so that New operating unit would be created this way also.
Kindly advice which is the best way to create new Operating Unit...
and also in Projects implementation setup ...starting organization LOV represent OU from HRMS or org Hierarchy...
Kindly clarify...
Thanks a lot n advance...

I create 3 OUs this using GL > Accounting Setup Manager ... under the primary Ledger (by attaching LE and BG).....but I am not able to find/search that in HR under Work structures > Organization > Description. Although it is available in the LOV while defining the profile option "MO: Operating Unit" ....and it is present in the Database table '*hr_all_organization_units*' too with the 'Type' column as empty (ideally it should be 'OU').
It makes me feel that in any case I would have to create the OU in HR as a mandatory setup!....am I correct?

How to create a new Business Unit

Hello,
I have problem.
Can anyone tell me
1 : How to create a new Business Unit, New Company from Jd Edwards screen means webpage.
2 : Can i find the User Defined Codes means UDC in jd edwards screen.
Thanks,
Shakti Prasad Priyakumar.

First, let me confirm that you are on JDE World, and not JDE Enterprise One/One World. They are very different environments. JDE World is normally a green screen, IBM Client Access based system.
If you are on a JDE World menu and you have the proper security access, just type in UDC on the command line and hit <ENTER>. You hopefully are in a test environment when you do this, since it sounds like you have very little knowledge of JDE. The UDC screen will come up. If you know the system code and code of the UDC table you want to look at, you can key them in and bring up that table. Otherwise, do F5. That will let you search by system code and see what table codes are available in each system. If you are not sure what UDC table you need, you can look at the JDE data dictionary for the data item you are interested in and that will tell you the UDC table, if the data item is UDC based.
As for setting up new business units and company, get to the main general ledger menu. Don't remember the exact path, but you want to get into the setup/define menu for general ledger accounts. There will be separate options there for maintaining companies and for maintaining business units. You want to play with this in a test environment before you do anything for real.
Hope this helps a bit.
John Dickey

VPN Woes with new AP unit

Similar Messages

Maybe you are looking for