VRRP Issue on CSS 11501 !!Plz help
Hi, I have configured the VRRP on CSS properly and it had worked previously without any problem. The only change is i have moved the box from the old location to the new and have change the vlan and ip address rest everything is same.
Now the problem is both CSS are becoming Master kindly some one help me if i have to change anything back to work properly.
Output from the CSS-
CSS A# show virtual-routers
Virrtual-Routers:
Interface Address: 1.1.1.1 VRID: 2
Priority: 120 Config. Priority: 110
State: Master Master IP: 1.1.1.1
State Changes: 10 Last Change: 18/11/2008 00:31:21
Preempt: True Last Fail Reason: IF Down
CSS B# show virtual-routers
Virtual-Routers:
Interface Address: 1.1.1.2 VRID: 2
Priority: 80 Config. Priority: 90
State: Master Master IP: 1.1.1.2
State Changes: 8 Last Change: 18/11/2008 01:18:18
Preempt: False Last Fail Reason: IF Down
Anyhelp would be appriciated.
Thanks
Neha
Hi neha,
Plz find the procedure below for your query:-
After disabling the access-list reconfigure the access-list as mentioned below :-
acl 01
clause 10 permit any x.x.x.x x.x.x.x destination any sourcegroup NATvip
clause 20 permit any any destination any
apply circuit-(VLANabc)
This should solve your issue.
Plz rate if this help.
Regards
Shariff
Similar Messages
-
Wifi Not catching signal iphone 6 , disgusting
ok i understand , then help me out rather judging ....see again i had a chat with the customer executive saying they passed all the test hardware is fine ...okay the guided me to recovery mode restore then the problem remains the same wifi no signal to catch .....so they concluded eventhough the test shows no hardware issues ..still software is okay ..hardware is the issue....
y th **** is happening in such a sophisticated iphone ..they asked me to ship n get rpaired ..imagine i used it without a scratch or a fall for a month ..and this is payed off ..pity on -
am not able to log in to my user account after installation of OSXLion,have called up the support centre many times,but was left in vain ...i belief its a simple problem ,but why is apple support center not able to help me out ...have given them all the required information with respect to everything...somebody plz help me to log in as am not able to access my docs and do any work...
My phone works all fine when am in mumbai but as soon s i leave mumbai I am not able to make an otgoing call
This is entirely a carrier issue. If your carrier (airtel) doesn't provide service outside of Mumbia, this has nothing to do with your iPhone.
i feel i need to change my brand
This is a user-to-user tech support forum, not Apple. No one here cares at all about your threats.
NEVER post personal info in this public forum -
Plz help me solving following issues
Hi SD experts,
Plz help me solving following issues
1) What do you mean by POD(proof of delivery) what is the use of pod? What are the con figuration you done in your project?
2) When I am punching order after entering data like material No and quantity system should pop-up a screen of delivery date and status and invoice data and details, How can we configure this?
3) Client requirement is he want horizon period in days format. but standard sap system It's in months format(gray mode). how can we change months to days?
4) Quotation has been created for product-D, 10 quantities, sales order is created with reference to the quotation, system copies 10 quantities in sales order. How do you restrict in sales order end user should not change quantities, system should not allow for changes by en user?
5) when i creating the sales order the system show error "No customer master record exist for sold to party". How to rectify it?
suitable solutions will be rewarded
thansx & regardshi,
Proof of delivery (POD) is an instrument involved in business processes in which an invoice is issued only after the customer has confirmed the delivery's arrival. In addition to the proof of delivery itself, you can also record the POD date, POD time, the actual quantity that arrived and the reason for possible differences in quantities. This is especially important for deliveries where the delivery quantity varies because of the nature of the goods or for which the exact delivery quantity is unknown from the start.
You are now in a position to issue an accurate invoice based on the customer's confirmation of goods received. You no longer need to create credit memos. The reasons for deviation that occur most frequently in "real world" scenarios such as stock shrinkage, theft, certain characteristics of goods (volatility, for example), and transportation damage are recorded and analyzed in the system. This analysis is especially valuable when you are negotiating with forwarding agents, vendors, or customers, since all deviations can be reflected
With regards
Rajesh -
Plz help production issue(smartform)
hi experts plz help its a production issue
i have a box in my smartform in which in one line i can only show 50 characters .and i have a text of 70 characters but i only have to show 50 characters from 70 characters .
now wat i did i stored 70 characters variable into 50 char variable abd displaying it .
but the issue is
if i want to print .
hi this is sdn and here u can get all the information about sap .
now lets say
i of information is the 46th character of my line
now what is happening it is coming like
hi this is sdn and here u can get all the
infor
its showing 50 character only but if word is not completed it is printing it in next line.
it should print like
hi this is sdn and here u can get all the infor
plz help how to do it
thanx in advance .code i am using is ::::::::::::::::::::::::::::::::::::::::::::::::
data : TEXT_3I56(50) type c .
move is_bil_invoice-hd_gen-bil_number TO textname.
CALL FUNCTION 'READ_TEXT'
EXPORTING
CLIENT = SY-MANDT
id = '0002'
language = is_nast-spras
name = textname
object = 'VBBK'
ARCHIVE_HANDLE = 0
LOCAL_CAT = ' '
IMPORTING
HEADER =
tables
lines = t_lines_3156
EXCEPTIONS
ID = 1
LANGUAGE = 2
NAME = 3
NOT_FOUND = 4
OBJECT = 5
REFERENCE_CHECK = 6
WRONG_ACCESS_TO_ARCHIVE = 7
OTHERS = 8.
IF sy-subrc <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
*describe table t_lines lines n.
*if not n is initial.
*bank_note = 'X'.
*endif.
READ TABLE T_LINES_3156 INDEX 1 .
IF SY-SUBRC = 0 .
TEXT_3I56 = T_LINES_3156-TDLINE .
ENDIF. -
Plz help upgrade issue moving data from char type structure to non char typ
Hi Experts
plz help its very urgent
Data :workout(5000) .
FIELD-SYMBOLS : <FS_WORKOUT> TYPE ANY.
workout = ' u' .
ASSIGN WORKOUT TO <FS_WORKOUT> CASTING TYPE C .
BAPISDITM = <FS_WORKOUT>.
i am getting dump after BAPISDITM = <FS_WORKOUT>.
i think i am getting the dump bcoz i am moving character type structure to non character type structure but i think with field symbols we can remove this issue thats y i used it but its not working plz help me
its very urgent
*dump is :*
Short text
Data objects in Unicode programs cannot be converted.
What happened?
Error in the ABAP Application Program
The current ABAP program "ZSDR0009" had to be terminated because it has
come across a statement that unfortunately cannot be executed.
How to correct the error
Use only convertible operands "dst" and "src" for the statement
"MOVE src TO dst"
If the error occures in a non-modified SAP program, you may be able to
find an interim solution in an SAP Note.
If you have access to SAP Notes, carry out a search with the following
keywords:
"UC_OBJECTS_NOT_CONVERTIBLE" " "
"ZSDR0009" or "ZSDR0009_I02"
"USER_COMMAND"
thanx in advancei got d solution in this thread
Hi all,
data: gv_line(6000) type c.
Bvbapkom = gv_line.
But i am getting the Error like : gv_line and Bvbapkom are not mutually convertable.
Note: Bvbapkom is a Structure
How do i solve this ?
Mahesh
KR
Posts: 210
Registered: 11/24/06
Forum Points: 0
Re: gv_line and Bvbapkom are not mutually convertable.
Posted: Nov 30, 2007 8:40 AM in response to: KR Reply
Hi ,
i got the solution
ANSWER:
Field-symbols: <X_Bvbapkom> type x,
<X_gv_line> type x.
Assign: Bvbapkom to <X_Bvbapkom> casting,
gv_line to <X_gv_line> casting.
<X_Bvbapkom> = <X_gv_line>.
Nasaka Ramakris...
Posts: 4
Registered: 1/19/08
Forum Points: 20
Re: gv_line and Bvbapkom are not mutually convertable.
Posted: Jan 19, 2008 7:42 AM in response to: KR Reply
Hi Check this answer.
ANSWER:
Field-symbols: <X_Bvbapkom> type x,
<X_gv_line> type x.
Assign: Bvbapkom to <X_Bvbapkom> casting,
gv_line to <X_gv_line> casting.
<X_Bvbapkom> = <X_gv_line>. -
CSS 11501 Load Balancing Issue
Hi,
We are facing some issue in load balancing in cisco CSS 11501 as we are not able to access the application through virtual IP. Below is the ruuning configuration of the CSS:
CSS11501# sh running-config
!Generated on 10/06/2010 16:51:34
!Active version: sg0810106
configure
!*************************** GLOBAL ***************************
ip route 0.0.0.0 0.0.0.0 132.186.199.1 1
!************************** CIRCUIT **************************
circuit VLAN1
ip address 132.186.199.145 255.255.255.0
!************************** SERVICE **************************
service Server1
ip address 132.186.199.243
port 5001
protocol tcp
keepalive port 5001
active
service Server2
ip address 132.186.199.246
protocol tcp
port 5001
keepalive port 5001
active
!*************************** OWNER ***************************
owner L5_Owner
content L3_Rule
vip address 132.186.199.146
protocol tcp
port 5001
add service Server1
add service Server2
active
content L5_Rule
vip address 132.186.199.146
add service Server1
add service Server2
protocol tcp
port 5001
url "//132.186.199.146:5001/emi"
active
CSS11501#
Observation : We are able to telnet on VIP: 132.186.199.146 on port 5001, but not able to access the application.
In Actual scenarion customer access application by accessing URL: http://132.186.199.243:5001/emi and once he enter this URL in web browser the request redirects ( by server itself) to URL: https://132.186.199.44:6002/cas/login?service=http%3A%2F%2F132.186.199.243%3A5001%2Femi%2Findex.jsp&acceptStrength=BASIC on backend server for user authenticaton and once user is authenticated then it again redirect to main URL ( http://132.186.199.243:5001/emi ) to access the application but when we are trying to access the application through VIP ( URL: http://132.186.199.146:5001/emi) we are not getting the login page as the request is not gettting redirected to backend server for user authentication.
Please suggest a solution here.The problem is that you are in one-armed mode.
So you need to configure client nat.
Without nating the client ip address, the server response goes back directly to the client and bypasses the CSS.
Therefore the client receives a response from an unknown server ip address (not the vip).
So configure a group.
For example
group Client
vip address 132.186.199.146
add destination service Server1
add destination service Server2
active
Also, remove the url command from your content rule.
It is useless in your case and will just make performance worst.
Gilles. -
Hi iam using IPHONE4 , when i coonect it to my PC , itunes get hang and don't detect my iphone , how i can sort out this issue plz help me
iPhone, iPad, or iPod touch not appearing in iTunes
-
CSS 11501 - Network reconnection issue
Using a CSS 11501 switch to configure both Load balancing and server hot standby between two servers (of same config). Clients are connecting to the server using tcp/ip sessions.
The configuration used is shown below:
=========================================
configure
ip route 0.0.0.0 0.0.0.0 10.167.50.1 1
!************************* INTERFACE
interface e2
bridge vlan 9
interface e3
bridge vlan 9
!************************** CIRCUIT
circuit VLAN1
ip address 10.167.50.108 255.255.254.0
circuit VLAN9
ip address 10.167.70.1 255.255.254.0
!************************** SERVICE
service abc_service1
ip address 10.167.70.2
protocol tcp
port 6300
keepalive type tcp
active
service abc_service2
ip address 10.167.70.3
protocol tcp
port 6300
keepalive type tcp
active
!*************************** OWNER
owner xxxxx
content abc_crule
vip address 10.167.50.109
add service abc_service1
add service abc_service2
protocol tcp
port 6300
balance aca
active
===============================
We conducted three tests to verify the hot standby while client sending the data to server app thro tcp/ip.
1) Brought down the service on one server 2) Restarted the OS (Windows 2003) on one server 3) Removed a network cable of one of the server connecting to CSS.
client app lost the conn to the service/server, but when it tried reconnecting to the alternate server, it was successful.
CSS status reflected the actual status of the service/server.
But in third test (removing network conn) the service state changed from "Alive" to "Down" and client app lost conn to the server. Client app tried reconnecting and it was successful connecting to the alternate server.
But when we connected the network cable back, the CSS state was continue to be in "Down". Also,the network connection between CSS and server was not available after reconnection. Also, the status of alternate server changed to "Down", but still client app was successfully transmitting to the alternate server. Stopping the client app and tried reconnecting,
the connection was not going thro.
The connection could be established between CSS and server boxes only after restarting the OS(running windows 2003).
Issues:
1. Service status in CSS continue to be down even after reconnecting the cable with the service running.
2. CSS status of the first service also went down after reconnecting the other server.
3. Client app could not reconnect to any of the servers.
Are we missing any configuration parameter in CSS which will address the above?
regards
ParamParam,
what software version for the CSS ?
Did you see an ARP entry on the server for the CSS ?
Did you see an ARP entry on the CSS for the server ?
is the server directly connected to the CSS or is there an L2 switch inbetween ?
Could you configure 'bridge spanning-tree disabled' on the CSS and see if this improves the situation.
Regards,
Gilles. -
Issue with tables :( Plz Help!
Hey all!
Never posted before on this forum and pretty new with
dreamweaver. So I'm having the strangest issue with dreamweaver
tables. I bought a template that I'm modifying by my self which
isnt all that hard haha. But Here's what I ran into. Whenever I put
one table and then another one under it and another one under it
and I insert txt or pics in there and save it, after I upload it
and preview it, I can only see the info from the first table.
Everything else under it, wont show up.
So no matter where and on what page I do it from that
template, if I put more than 1 table down, it'll only show the info
from the first and top table and everything else in other tables
under it, wont show up at all (after I upload it) even thou it
looks good on dreamweaver itself :(
Is there an option to enable or disable something? Plz help,
thank you all!"Unknown7" <[email protected]> wrote:
> So no matter where and on what page I do it from that
template, if I put more
>than 1 table down, it'll only show the info from the
first and top table and
>everything else in other tables under it, wont show up at
all :(
>
> Is there an option to enable or disable something? Plz
help, thank you all!
The bad news is that if you want to do anything remotely
complicated with
Dreamweaver you will have to learn a fair amount about HTML.
I would virtually
guarantee that when you put your new table in something is
going wrong so that
one or other table is not being defined correctly.
As you are modifying someone else's template there is
virtually no way to find
out what is happening other than to examine the HTML. It is
unlikely that
fiddling with any Dreamweaver settings will make any
difference.
Every table should start with something like:
<table width="100%" border="0" cellspacing="0"
cellpadding="5"
bgcolor="#e0e0ff">
<tr align="center" valign="middle">
<td width="9%"><a href="#Bottom">
and end with:
</td>
</tr>
</table>
You can have more or less as many columns as you like in a
table, (<td> ...
</td>
And more or less as many rows ( <tr><td> ...
</td></tr>) as you like, but
unless you get up to special tricks you should have the same
number of columns
in every row. You can put anything you like -- images, more
tables, whatever --
inside a cell e.g.:
<td> image, blah, table </td>,
but you mustn't put any content anywhere else, and every
opening definition
(<table>, <tr>, <td> must have a matching
closing definition in the correct
order.
You can nest tables more or less indefinitely, but
Dreamweaver Design View
sometimes blows its top if you go more than three deep.
HTML usually doesn't produce any error messages, but the
effect of omitting any
of the steps in building a page is quite unpredictable.
Sometimes a major error
will not produce any visible effect, but on other occasions a
minor error will
send the page completely haywire.
You may care to have a look at:
http://www.corybas.com/Technical/Wrapping.htm
This has a series of demonstration pages illustrating what
happens when you try
to display increasingly complicated page layouts on narrow
screens.
Once you have learnt to interpret HTML, you can often learn a
lot by inspecting
the source code for the page (in IE click view, then Source).
This works with
anybody's page, so you can look at the source code for my
pages if you wish.
Clancy -
When the user Miro Generating:-
1. Give the Ref.No.Business places,
service Sheet No.
and the G/L No.. its take in production server,
But here actual its upated Medical Aid,G/l
But its comes in Rawmaterial exemption,account i.e not relevant account
actual Here its comes in G/L medical account
How its overthe issue plz help for me.
2.In before indevelopment server do that same thing in DEvelopment server, its Give the Error mesage i.e DELIVRY NOT SERIVICE ETNRY SHEET ..............(number) doest not exitHello,
There are several public KB articles that may apply to your situation. But, rather than try and list them all here for you, I suggest you go here:
http://btsc.webapps.blackberry.com/btsc/microsites/microsite.do
Search on the exact error message and see any of the resulting articles are on point to your situation.
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code -
Plz help guys
Hi Suren7669,
Welcome to the Support Communities!
To resolve this issue, I would suggest updating your iOS to the latest, which is 7.0.3.
iOS 7.0.3
http://support.apple.com/kb/DL1691
iOS: How to update your iPhone, iPad, or iPod touch
http://support.apple.com/kb/HT4623
Cheers,
- Judy -
my ios is 5.1.1 but still im facing to this issue, this is very annoying... plz help me
You need to tell us what "this issue" is if you want help.
-
Lsmw issue plz help its urgent
Hi Experts ,
i need to create a LSMW using batch input .
but the requirement is on the basis of conditions my recording need to be changed .
dat means
3127POL09 3127POL09-1 CTR 3127-1003E 100 FUL
3127POL09 3127POL09-2 WBS 3127POL01 60 FUL
for ctr i ill have to post data in screen number 200
and for wbs i ill have to post data in screen number 400 .
can we put some conditions in recording in lsmw ?
i no we can create multiple recording but how can we use them to fullfill my requirement .
plz help its urgent
thanx in advanceHi,
Within LSMW, there is an option to write our own code wherein this code can be incorporated.
This is in the Field Mapping Option...
Just go to the Menu Extras->Layout
and click on the check box Form Routines
Global Data.
Here you can define Global Variables and also perform your ABAP Coding.
Regards,
Balaji. -
Function group issue in upgrade plz help very urgent
hi gurus,
plz help me
in a big trouble.
deadline is today.
when i activated the function group i found this error in an include
LSVARCLS
and when i clicked to this field it took me to another include
LSVARTOP
here i found
data: f4_params type onf4_event_parameters_type.
FYI:
types: begin of onf4_event_parameters_type.
types: c_fieldname type lvc_fname.
types: cs_row_no type lvc_s_roid.
types: cr_event_data type ref to cl_alv_event_data.
types: ct_bad_cells type lvc_t_modi.
types: c_display type char01.
types: end of onf4_event_parameters_type.
data: f4_params type onf4_event_parameters_type.
error is :
Field "F4_PARAMS-C_FIELDNAME" is unknown. It is neither in one of the
specified tables nor defined by a "DATA" statement . . . . . . . . . .
thanks in advanceFUNCTION-POOL ZVAR MESSAGE-ID DB.
TABLES:
TADIR, " Entwicklungsklasse
TRDIR, " Reportcatalog
LDBD, " logical databases
VARID, " variant properties
RSVAVA, " Variable data in
" variants( sy-datum)
RSVAR, " new RALDB structure
RSVARDESC, " Report, Variante, Dynnr
VARIT, " variants texts
VARIS, " screennr per variant
DD23T, "
DFIES, "DD-Schnittstelle, get_field
TPARAT, "Texte zu Memory-Ids
TVARUVN, "#EC NEEDED
SSCRFIELDS,
t000.
DATA CHOOSE like sy-ucomm value 'PICK'.
DATA G_STATUS like sy-pfkey.
*Includes für Icons
INCLUDE .
Include für Symbole
INCLUDE .
*Equates für SSCR
INCLUDE RSDBCOM2.
*Typen für dynamische Selektionen, verwendet bei RS_REFRESH_...DYNAMICAL
TYPE-POOLS: RSDS, SYLDB, sydb0.
data: GS_TOOLBAR TYPE STB_BUTTON.
include lsvarcls.
Key um unnoetige Datenbankzugriffe zu vermeiden
DATA: BEGIN OF CHECK_KEY,
REPORT LIKE RSVAR-REPORT,
VARIANT LIKE RSVAR-VARIANT.
DATA: END OF CHECK_KEY.
key für get_description
*DATA: old_key LIKE check_key.
CATALOG OF VARIANTS, OLD STRUCTURE. WILL BE DELETED BY FIRST
CALL OF VARIANTS OUT OF FUNCTIONPOOL SVAR.
INFORMATION WILL BE TRANSFERED TO VARID AND VARIT.
DATA: VARCAT LIKE RSVARC OCCURS 20 WITH HEADER LINE.
TEXT (=> VARIT)
DATA: VARCATT LIKE RVART OCCURS 20 WITH HEADER LINE.
SAVE INFORMATION ABOUT VARIANTS
DATA: BEGIN OF SAVEINFO OCCURS 20,
NAME LIKE RVARI-NAME,
NUMB LIKE RVARI-NUMB,
PROTECTED LIKE RVARI-PROTECTED,
FIELDTEXT LIKE RSVAR-FIELDTEXT,
KIND LIKE RVARI-KIND,
TYPE LIKE RVARI-TYPE,
VTYPE LIKE RVARI-VTYPE,
VNAME LIKE RVARI-VNAME,
appendage I= Matchcode, C=Checkbox etc
APPENDAGE LIKE RSVAR-INVISIBLE,
VARIS(1), " TVARV, FUBAU
N= Ausgeblendet von Report,X ausgeblendet in Variante
INVISIBLE,
USER,
MEMORYID LIKE RSSCR-SPAGPA,
nur auf einem Bild vorhanden
GLOBAL,
NO_IMPORT,
SPAGPA,
NOINTERVALS,
OBLIGATORY LIKE RSVAR-OBLIGATORY,
RADIO,
END OF SAVEINFO.
DATA: BEGIN OF SAVEINFO_DYN OCCURS 10,
TABLENAME LIKE RSDSTABS-PRIM_TAB,
FIELDNAME LIKE RSDSTABS-PRIM_FNAME,
FIELDTEXT LIKE RSVAR-FIELDTEXT,
TYPE LIKE RVARI-TYPE,
VTYPE LIKE RVARI-VTYPE,
VNAME LIKE RVARI-VNAME,
VARIS(1),
PROTECTED LIKE RVARI-PROTECTED,
GLOBAL(1).
DATA: END OF SAVEINFO_DYN.
data: saveinfo_sav like saveinfo occurs 0 with header line.
data: saveinfo_dyn_sav like saveinfo_dyn occurs 0 with header line.
key for import of variants from VARI
DATA: BEGIN OF $RKEY,
REPORT LIKE RSVAR-REPORT,
VARIANT LIKE RSVAR-VARIANT,
END OF $RKEY.
vari
DATA: L_VARI LIKE RVARI OCCURS 20 WITH HEADER LINE.
%_SSCR
DATA SELCTAB LIKE RSSCR OCCURS 20 WITH HEADER LINE.
DATA GLOB_SUBMODE(2).
DATA LOC_SUBMODE(2).
screenfields
DATA: XCODE(4).
DATA: FCODE(4) TYPE C,
FUNC(4) TYPE C.
DATA: BEGIN OF INFO OCCURS 20,
FLAG,
OLENGTH TYPE X,
LINE LIKE RSVAR-INFOLINE,
END OF INFO.
DATA: VALUTAB LIKE RSPARAMSL OCCURS 40 WITH HEADER LINE.
Zur allgemeinen Verwendung
FIELD-SYMBOLS: .
DATA ILLEGAL_CHAR. " Wrong sign in variant
copy
DATA: VARIANT2 LIKE RSVAR-VARIANT,
VARIANT1 LIKE RSVAR-VARIANT.
*list of parameters and select-options, screenobjects
DATA: L_SELOP LIKE VANZ OCCURS 20 WITH HEADER LINE.
DATA: L_SELOP_NONV LIKE VANZ OCCURS 20 WITH HEADER LINE."nonv = non visi
DATA: L_PARAMS LIKE VANZ OCCURS 20 WITH HEADER LINE.
DATA: L_PARAMS_NONV LIKE VANZ OCCURS 20 WITH HEADER LINE.
DATA: SCREENOBJECTS LIKE VANZ OCCURS 20 WITH HEADER LINE.
list of all variants concerning one report
DATA: BEGIN OF VARI_LIST OCCURS 40,
MARKFIELD LIKE RSVAR-MARKFIELD,
VARIANT LIKE RSVAR-VARIANT,
TEXT LIKE RVART-VTEXT,
ENAME LIKE RSVARC-ENAME,
AENAME LIKE RSVARC-AENAME,
PROTECTED LIKE RSVARC-PROTECTED,
ENVIRONMT LIKE RSVARC-ENVIRONMT,
XFLAG1 LIKE VARID-XFLAG1.
DATA: END OF VARI_LIST.
*Variablen für das Blättern auf den Dynpros 1303 und 306.
DATA: VARI_LIST_SCROLL LIKE SY-STEPL VALUE '1'.
DATA: SAVE_OKCODE(4).
table for Dynpro 306 (delete variants)
DATA: BEGIN OF H_VARILIST OCCURS 30,
MARKFIELD LIKE RSVAR-MARKFIELD,
FLAG1 LIKE RSVAR-FLAG1,
FLAG2 LIKE RSVAR-FLAG2,
FLAG3 LIKE RSVAR-FLAG3,
VARIANT LIKE RSVAR-VARIANT.
DATA: END OF H_VARILIST.
CONSTANTS: C_PDLIST_WIDTH TYPE I VALUE '24',
C_VARILIST TYPE I VALUE '10'.
DATA: CATTOP LIKE SY-TABIX VALUE '3'. "lines top-of-page in CATALOG.
*data: listtop like sy-tabix value '3'. "lines top-of-page in Delete
"vari
DATA: PRINT_ALL_VAR. "alle Varianten drucken
DATA: PRINT_CAT_VAR. "Katalog drucken
Systemumgebung
DATA ENVIRONMENT. " S: SAP, C: Customer
Dynpro 320
DATA : TEXT0(59).
*Tables and fields for fitting variants
*table of variants which must be fitted
DATA: BEGIN OF FIT_VAR OCCURS 50,
VARIANT LIKE RSVAR-VARIANT,
FLAG(1). " flag = 'X' => Variante can't be
DATA: END OF FIT_VAR. "fitted.
DATA: BEGIN OF SINGLE_OPTIONS OCCURS 8,
OPTION(2),
TEXT(18).
DATA: END OF SINGLE_OPTIONS.
variants which contain variables
internal table, per line select-options and parameters which
use variables
DATA: BEGIN OF VARIVAR OCCURS 20,
SELNAME LIKE RSSCR-NAME,
SELTEXT LIKE RSVAR-FIELDTEXT,
KIND LIKE RVARI-KIND,
TYPE LIKE RVARI-TYPE,
VTYPE LIKE RSVAR-VTYPE,
VTEXT LIKE RSVAVA-VTEXT,
FB,
TVARV,
VNAME LIKE RSVAR-VNAME,
OPTION LIKE RSVAR-OPTION,
SIGN(1),
INFO_TABIX LIKE SY-TABIX,
DATES_TABIX LIKE SY-TABIX,
USER,
MEMORYID LIKE TPARA-PARAMID,
END OF VARIVAR.
DATA: BEGIN OF VARIVAR_DYN OCCURS 20,
TABLENAME LIKE RSDSTABS-PRIM_TAB,
FIELDNAME LIKE RSDSTABS-PRIM_FNAME,
KIND LIKE RVARI-KIND,
TYPE LIKE RVARI-TYPE,
VTYPE LIKE RSVAR-VTYPE,
VTEXT LIKE RSVAVA-VTEXT,
FB,
TVARV,
VNAME LIKE RSVAR-VNAME,
OPTION LIKE RSVAR-OPTION,
SIGN(1),
INFO_TABIX LIKE SY-TABIX,
DATES_TABIX LIKE SY-TABIX,
END OF VARIVAR_DYN.
DATA: VARIDATE_S LIKE RSVARIVAR OCCURS 20 WITH HEADER LINE.
Tabelle der möglichen Datumsberechnungen für Variablen in Varianten
Parameter
DATA: VARIDATE_P LIKE RSVARIVAR OCCURS 20 WITH HEADER LINE.
table of possible TVARV-variables (parameters)
DATA: TVARV_P LIKE TVARV OCCURS 20 WITH HEADER LINE.
table of possible TVARV-variables (select-options)
DATA: TVARV_S LIKE TVARV OCCURS 20 WITH HEADER LINE.
description of fields VARIDATES
DATA: FIDESC_DATES LIKE RSVBFIDESC OCCURS 5 WITH HEADER LINE.
description of fields TVARV
DATA: FIDESC_TVARV LIKE RSVBFIDESC OCCURS 5 WITH HEADER LINE.
description of fields OPTION
DATA: FIDESC_OPTION LIKE RSVBFIDESC OCCURS 5 WITH HEADER LINE.
description of fields OPTION
Feldtabelle für DYNP_VALUES_READ/UPDATE
DATA DYNPFIELDS LIKE DYNPREAD OCCURS 50 WITH HEADER LINE.
*desctab
DATA: DESCTAB LIKE RSBREPI OCCURS 20 WITH HEADER LINE.
*Hilfsfelder für Übergabeparameter
DATA:G_SUBRC LIKE SY-SUBRC,
L_RC LIKE SY-SUBRC.
*Hilfsfelder für Sperren
DATA: G_ENQSUB LIKE SY-SUBRC.
*Hilfsfeld für mandantenabhängiges Löschen von Varianten
DATA: DEL_ALL_VAR. "=X alle Mandanten, =' ' nur aktueller Mandant
select variant form list.
DATA: BEGIN OF VARIANT_TABLE OCCURS 30,
VARIANT LIKE RSVAR-VARIANT,
TEXT LIKE VARIT-VTEXT,
ENVIR LIKE VARID-ENVIRONMNT,
ENAME LIKE VARID-ENAME,
AENAME LIKE VARID-AENAME,
aedat like varid-aedat,
MLANGU LIKE VARID-MLANGU,
protected like varid-protected,
SELSCREEN(80). "<= 20 Bilder
DATA: END OF VARIANT_TABLE.
DATA: CALL_FLAG. "screen 305.
DATA: MODE_FLAG.
Print variants screen 308
DATA: PRINT_LIST LIKE RSREPVAR OCCURS 30 WITH HEADER LINE.
parameters in variables
DATA: BEGIN OF VARIVDAT OCCURS 5,
SELNAME LIKE RVARI-NAME.
INCLUDE STRUCTURE RSINTRANGE.
DATA: END OF VARIVDAT.
DATA: VARIVDAT_WORK LIKE VARIVDAT OCCURS 10 WITH HEADER LINE.
DATA:EXC_SUBC LIKE SY-SUBRC.
DATA: BEGIN OF LDB_VARIVAR OCCURS 10,
MARKFIELD LIKE RSVAR-MARKFIELD,
VTEXT LIKE RSVARIVAR-TEXT,
VTYPE LIKE RSVAR-VTYPE.
DATA: END OF LDB_VARIVAR.
*generate subroutinepool
DATA: BEGIN OF REPDAT_TAB OCCURS 40,
LINE(72),
END OF REPDAT_TAB.
*Tabelle zur Übergabe der alten Selektionswerte wenn sich
*Parameter oder Select-Options geändert haben.
*Wird von rs_variant_obsolet benötigt.
DATA: OLD_SELECTIONS LIKE RSPARAMSL OCCURS 20 WITH HEADER LINE.
*Flag für Aufruf aus QUERY und Report-Writer.
*Reportname auf Einstiegsbild nicht sichtbar (not_visible = x)
DATA: NOT_VISIBLE.
*Varianten für Query
DATA: QUERY_SYSVAR.
*Einstiegsbild mit anderem Titel aufrufen.
DATA: N_TITLE(40).
*F4 Hilfe RS_VARIANT_CATALOG mit anderem Titel aufrufen
DATA: G_TITLE like sy-title.
*Unterscheidung auf Listdynpro (hauptsächlich 307)
DATA: CALLER(4).
*sy-subrc Felder für Import und Export.
DATA: EXP_SUBRC LIKE SY-SUBRC,
IMP_SUBRC LIKE SY-SUBRC.
*Tabellen für dynamische Selektionen
DATA: DYNSEL_DESC LIKE RSDYNBREPI OCCURS 5 WITH HEADER LINE.
DATA: DYNS_FIELDS LIKE RSDSFIELDS OCCURS 5 WITH HEADER LINE.
DATA: DYNSEL_VALUE LIKE RSSELDYN OCCURS 5 WITH HEADER LINE.
*tabellen für matchcodeselection
DATA: BEGIN OF MC_DESC OCCURS 5,
NAME LIKE RSSCR-NAME,
ID LIKE MCPARAMS-MCID,
OBJECT(10),
S_STRING LIKE MCPARAMS-STRING,
D_TEXT LIKE DD23T-MCTEXT,
FROM LIKE VANZ-FROM,
TO LIKE VANZ-TO.
DATA: END OF MC_DESC.
*Tabelle für Umsetzung dynamische Selektionen
*flag = space -> umgesetzt
*flag = G -> Variante z.Z gesperrt
*flag = I -> Fehler beim Import
DATA: BEGIN OF CHANGED_VARIANTS OCCURS 10,
NAME LIKE RSVAR-VARIANT,
FLAG.
DATA: END OF CHANGED_VARIANTS.
*Feld für Ikonen auf Dynpros.
DATA: IKON(8).
*Konstanten für Ikonen
CONSTANTS: POP_WARNING(8) VALUE '@1A@',
POP_ERROR(8) VALUE '@1B@',
POP_INFO(8) VALUE '@19@',
POP_COPY(8) VALUE '@14@',
c_icon_enter_more(15) value 'ICON_ENTER_MORE',
C_ICON_DISPLAY_MORE(17) VALUE 'ICON_DISPLAY_MORE'.
DATA: MORE_ICON LIKE RSSELINT-OPTI_PUSH.
*Konstanten für Variante ändern, Werte oder Attribute
CONSTANTS: C_VAL VALUE 'V'.
Interne Tabelle für Transport
DATA: BEGIN OF REP_VAR OCCURS 10,
MARKFIELD.
INCLUDE STRUCTURE $RKEY.
DATA: END OF REP_VAR.
DATA: REP_VAR_CURSOR LIKE SY-INDEX VALUE 0.
Tabelle für RS_SELOPT_INFO -> BBS
DATA: DEFAULTS LIKE RSPARAMSL OCCURS 10 WITH HEADER LINE.
Tabelle für Werteanzeige Tvarv.
DATA: TVARVTAB LIKE TVARV OCCURS 10 WITH HEADER LINE.
SUBTY-Equates
INCLUDE RSDBCSTY.
Textfeld für Dynpro 317.
DATA: TEXT(4).
Konstante für Namenskonvention Systemvariante
CONSTANTS: SYS_VNAME(4) VALUE 'SAP&'.
CONSTANTS: CUS_VNAME(4) VALUE 'CUS&'.
Flag für Systemvariante gewünscht.
DATA: C_SYSVAR.
data vari_mandt like sy-mandt.
data sysvar_mandt like sy-mandt value '000'.
Check für Systemvariante
DATA: SYSVAR_FLAG.
Flag für Entwicklungsklasse , Werte Y oder N (aus get_devcalss)
DATA: NON_LOCAL VALUE 'Y'.
DATA: TABIX LIKE SY-TABIX.
*Strutur für freie Abgrenzungen.
DATA: VARIDYN LIKE RSVARIDYN OCCURS 10 WITH HEADER LINE.
DATA: VDATDYN LIKE RSVDATDYN OCCURS 10 WITH HEADER LINE.
DATA: VARIVDAT_DYN LIKE RSVDATDYN OCCURS 10 WITH HEADER LINE.
DATA: BEGIN OF VARIVDAT_DYN_WORK OCCURS 10,
TABLENAME LIKE RSVARIDYN-TABLENAME,
FIELDNAME LIKE RSVARIDYN-FIELDNAME.
INCLUDE STRUCTURE RSINTRANGE.
DATA: END OF VARIVDAT_DYN_WORK.
CONSTANTS: NO_IMPORT VALUE SPACE.
Teilt IM/EXPORT_VARIANT_STATIC mit, welche übergebeneb Objekte
im/exportiert werden sollen.
DATA: BEGIN OF IMEX,
VARI,
DYNS,
END OF IMEX.
Tabelle für Selektionsbildnummern
DATA: DYNNR LIKE RSDYNNR OCCURS 10 WITH HEADER LINE.
DATA: BEGIN OF CHOOSE_DYNNR OCCURS 10,
MARKFIELD.
INCLUDE STRUCTURE RSDYNNR.
DATA: END OF CHOOSE_DYNNR.
Sichern vom Selektionsbild, RSVAR_VARIANTT zurücksetzen
DATA: FLAG_FIRST. "#EC NEEDED
DATA: FLAG_PROTECTED. "#EC NEEDED
Daten für CALL SELECTION SCREEN Varianten
DATA: HIDE_FLAG.
DATA: LINE_NUMBER LIKE SY-TABIX.
DATA: VARISCREENS LIKE RSDYNNR OCCURS 10 WITH HEADER LINE.
data: variscreens_sav like rsdynnr occurs 10 with header line.
DATA: FLAG_1000.
DATA: DYNNR_TFILL LIKE SY-TFILL.
DATA: VARISCREENS_TFILL LIKE SY-TFILL.
DATA: DMORE_ICON(40).
DATA: BEGIN OF GLOBAL_OBJECTS OCCURS 10,
NAME LIKE RSSCR-NAME,
END OF GLOBAL_OBJECTS.
DATA: BEGIN OF DYN_TAB OCCURS 10,
DBFIELD LIKE RSSCR-DBFIELD,
END OF DYN_TAB.
CONSTANTS: C_P_COLUMN TYPE I VALUE 38,
C_I_COLUMN TYPE I VALUE 41,
C_N_COLUMN TYPE I VALUE 44,
C_S_COLUMN TYPE I VALUE 47,
C_W_COLUMN TYPE I VALUE 50,
C_M_COLUMN TYPE I VALUE 53,
C_O_COLUMN TYPE I VALUE 56,
MAX_WIDTH_ATTR TYPE I VALUE 77.
CONSTANTS: MAX_WIDTH_SELVAR TYPE I VALUE 57.
DATA: FLAG_NOIMPORT.
DATA: CURR_STATUS(4).
DATA: SCREEN_TITLES LIKE RSSCRITLE OCCURS 10 WITH HEADER LINE.
RANGES V_RANGE FOR VARID-VARIANT OCCURS 10.
DATA: FLAG_ALL_SCREENS.
CONSTANTS: C_LOW TYPE I VALUE 34,
C_HIGH TYPE I VALUE 58,
C_TO TYPE I VALUE 54,
C_OUTPUT_LENGTH TYPE I VALUE 26,
C_DISPLAY_LENGTH TYPE I VALUE 87,
C_DISPLAY_LENGTH_ATTR TYPE I VALUE 104,
C_DISPLAY_LENGTH_CAT TYPE I VALUE 118,
C_NO VALUE '0',
C_DYNNR LIKE SCREEN-NAME VALUE 'RSVAR-DYNNR',
C_ICON_MORE LIKE SCREEN-NAME VALUE 'DMORE_ICON',
C_SCREEN_1000 LIKE SY-DYNNR VALUE '1000'.
DATA: BELONGING_DYNNR LIKE RSDYNNR OCCURS 10 WITH HEADER LINE.
DATA: PREFIX(20).
DATA: D_320_TEXT(35).
DATA: OLD_VARI LIKE RSVAR-VARIANT.
DATA: L_SUBMODE LIKE GLOB_SUBMODE.
DATA: ICON_1(40), ICON_2(40), ICON_3(40).
DATA: FLAG_ICON_1, FLAG_ICON_2, FLAG_ICON_3.
DATA: FLAG_CALLED_FROM_SELSCREEN.
DATA: VARIVAR_TEXT LIKE RSVAVA-VTEXT.
DATA: VARIVAR_KIND LIKE RSSCR-KIND.
DATA: LIST_LINE LIKE SY-LILLI.
DATA: MOD_LINE LIKE SY-LILLI.
DATA: G_SP TYPE SYLDB_SP.
DATA: G_RANGE TYPE RSDS_RANGE,
G_FRANGE TYPE RSDS_FRANGE,
G_RSDSSELOPT LIKE RSDSSELOPT.
DATA: G_ILL_CHAR.
DATA: FLAG_CHANGE_VARIANT.
DATA: EXIT_FLAG.
DATA: COMP_NODI_NAME LIKE RSSCR-NAME.
DATA: EXCLUDE LIKE RSEXFCODE OCCURS 0 WITH HEADER LINE.
hidefelder für Attributebild.
DATA: HIDE(10).
Feldbeschreibung aufgeklappt oder zugeklappt
DATA: STATE(4).
DATA: NO_DISPLAY_VISIBLE TYPE BOOLEAN VALUE 'F'.
DATA: READ_LINE LIKE SY-INDEX.
CONSTANTS: C_COLLAPSE(4) VALUE 'COLL',
C_EXPAND(4) VALUE 'EXPA',
C_TRUE VALUE 'T',
C_FALSE VALUE 'F'.
CONSTANTS: CAT_LINE_SIZE TYPE I VALUE '127'.
DATA: G_EXPOREP TYPE SY-REPID.
DATA: SUBSCREENPROG LIKE SY-REPID,
SUBSCREENDYNNR LIKE SY-DYNNR.
data: g_subc like trdir-subc.
data: status_for_subscreens.
Data for subscreen processing
data: begin of g_subscreen,
ucomm type syucomm,
submode(2),
total type i,
current type i,
exclude type rsexfcode occurs 0,
rkey type rsvarkey,
variscreens type rsdynnr occurs 0,
sscr type rsscr occurs 0,
end of g_subscreen.
INCLUDE SVARSELO.
Daten für ALV-GRID
data:
GT_TOOLBAR_EXCLUDING TYPE UI_FUNCTIONS,
GRID1 TYPE REF TO CL_GUI_ALV_GRID,
GRID2 TYPE REF TO CL_GUI_ALV_GRID,
alv_fieldcat TYPE LVC_T_FCAT WITH HEADER LINE,
EVENT_RECEIVER1 TYPE REF TO CL_EVENT_RECEIVEr1,
selected value 'X',
alv_layout TYPE LVC_S_LAYO,
alv_STABLE type LVC_S_STBL,
ROW_TABLE TYPE LVC_T_ROW WITH HEADER LINE,
alv_container_1 type REF TO CL_GUI_CUSTOM_CONTAINER,
alv_container_2 type REF TO CL_GUI_CUSTOM_CONTAINER.
constants: c_search value 'S'.
Maybe you are looking for
-
I bought a season of shows and i can't seem to watch some. It wont let me on my computer or Ipad.It will only let me wath like 30 seconds of it.
-
Order of songs in playlist?
Hi there, I have imported playlist "THE VERY BEST" from my dad's CD with cca 165 mp3's. They are properly labeled, with song name, artist and even album, but since it's compilation, they obviously do differ. They have proper track number, like 1 of 1
-
Update with dynamic top value in CTE
Hi, Scenario : I have 2 main tables. One is header level and another is detail level. Each header table records have multiple detail entries based on the header table Quantity. Eg: The header have Quantity 50, detail table have 50 receords. Likwise e
-
All of a sudden my weblogic server is giving error while I am trying to run startWeblogic.cmd The admin server log trace is : D:\Middleware\SOASuite11g\user_projects\domains\SOAOSBDevDomain\servers\AdminServer\data\ldap\XACMLRoleMappermyrealmInit.ini
-
Hi please help me, In perform and form what i have to pass please help me , The logic is here,Please help me CLEAR sel_list. CLEAR t_table. SORT t_table. DELETE ADJACENT DUPLICATES FROM t_table. PERFORM extract_table_a700 tables t_table .